summaryrefslogtreecommitdiff
AgeCommit message (Collapse)AuthorFilesLines
2008-07-03ARM: OMAP2: Clock: New OMAP2/3 DPLL rate rounding algorithmPaul Walmsley6-19/+258
This patch adds a new rate rounding algorithm for DPLL clocks on the OMAP2/3 architecture. For a desired DPLL target rate, there may be several multiplier/divider (M, N) values which will generate a sufficiently close rate. Lower N values result in greater power economy. However, lower N values can cause the difference between the rounded rate and the target rate ("rate error") to be larger than it would be with a higher N. This can cause downstream devices to run more slowly than they otherwise would. This DPLL rate rounding algorithm: - attempts to find the lowest possible N (DPLL divider) to reach the target_rate (since, according to Richard Woodruff <r-woodruff@ti.com>, lower N values save more power than higher N values). - allows developers to set an upper bound on the error between the rounded rate and the desired target rate ("rate tolerance"), so an appropriate balance between rate fidelity and power savings can be set. This maximum rate error tolerance is set via omap2_set_dpll_rate_tolerance(). - never returns a rounded rate higher than the target rate. The rate rounding algorithm caches the last rounded M, N, and rate computation to avoid rounding the rate twice for each clk_set_rate() call. (This patch does not yet implement set_rate for DPLLs; that follows in a future patch.) The algorithm trades execution speed for rate accuracy. It will find the (M, N) set that results in the least rate error, within a specified rate tolerance. It does this by evaluating each divider setting - on OMAP3, this involves 128 steps. Another approach to DPLL rate rounding would be to bail out as soon as a valid rate is found within the rate tolerance, which would trade rate accuracy for execution speed. Alternate implementations welcome. This code is not yet used by the OMAP24XX DPLL clock, since it is currently defined as a composite clock, fusing the DPLL M,N and the M2 output divider. This patch also renames the existing OMAP24xx DPLL programming functions to highlight that they program both the DPLL and the DPLL's output multiplier. Signed-off-by: Paul Walmsley <paul@pwsan.com> Signed-off-by: Tony Lindgren <tony@atomide.com>
2008-07-03ARM: OMAP2: Clock: Add OMAP3 DPLL autoidle functionsPaul Walmsley5-30/+376
This patch adds support for DPLL autoidle control to the OMAP3 clock framework. These functions will be used by the noncore DPLL enable and disable code - this is because, according to the CDP code, the DPLL autoidle status must be saved and restored across DPLL lock/bypass/off transitions. N.B.: the CORE DPLL (DPLL3) has three autoidle mode options, rather than just two. This code currently does not support the third option, low-power bypass autoidle. Signed-off-by: Paul Walmsley <paul@pwsan.com> Signed-off-by: Tony Lindgren <tony@atomide.com>
2008-07-03ARM: OMAP: Add OMAP chip type structure; clean up mach-omap2/id.cPaul Walmsley2-29/+205
Add a new OMAP chip identification interface, omap_chip_id. omap_chip_id is a structure which contains one bit for each OMAP2/3 CPU type, and on 3430, ES level. For example, the CHIP_IS_OMAP2420 bit is set in omap_chip at boot on an OMAP2420. On OMAP3430ES2, both CHIP_IS_OMAP3430 and CHIP_IS_OMAP3430ES2 bits are set. omap_chip is set in mach-omap2/id.c by _set_omap_chip(). Other code should use the omap_chip_is() function to test against omap_chip. Also, clean up id.c by splitting some code out of omap_check_revision() into its own function, _set_system_rev(); and converting some debug printk()s into pr_debug(). Second revision. Signed-off-by: Paul Walmsley <paul@pwsan.com> Signed-off-by: Tony Lindgren <tony@atomide.com>
2008-07-03ARM: OMAP: Turn CM and PRM access into functionsTony Lindgren4-7/+62
Otherwise compiling in omap2 and omap3 will not work. Signed-off-by: Tony Lindgren <tony@atomide.com>
2008-07-03ARM: OMAP: Introduce omap_globals and prcm access functions for multi-omapTony Lindgren11-58/+150
New struct omap_globals contains the omap processor specific module bases. Use omap_globals to set the various base addresses to make detecting omap chip type simpler. Also introduce OMAP1_IO_ADDRESS and OMAP2_IO_ADDRESS for future multi-omap patches. Signed-off-by: Tony Lindgren <tony@atomide.com>
2008-07-03ARM: OMAP: Remove __REG access for multi-omapTony Lindgren1-23/+0
This does not play nicely with multi-omap as it cannot be replaced by a function in io.c for omaps with different IO bases. Signed-off-by: Tony Lindgren <tony@atomide.com>
2008-07-03ARM: OMAP: USB: Change omap USB code to use omap_read/write instead of __REGTony Lindgren7-357/+499
Change omap USB code to use omap_read/write instead of __REG for multi-omap Cc: David Brownell <david-b@pacbell.net> Cc: linux-usb@vger.kernel.org Cc: i2c@lm-sensors.org Signed-off-by: Tony Lindgren <tony@atomide.com>
2008-07-03ARM: OMAP: Change omap_cf.c and omap_nor.c to use omap_readw/writew instead ↵Tony Lindgren4-28/+43
of __REG Change omap_cf.c and omap_nor.c to use omap_readw/writew instead of __REG. This is needed for multi-omap in the future. Cc: David Brownell <david-b@pacbell.net> Cc: linux-pcmcia@lists.infradead.org Cc: linux-mtd@lists.infradead.org Signed-off-by: Tony Lindren <tony@atomide.com>
2008-07-03ARM: OMAP: CLKFW: Initial debugfs support for omap clock frameworkHiroshi DOYU2-36/+95
debugfs can provide the infrastructure to trace the dependencies of clock tree hierarchy quite visibly. This patch enables to keep track of clock tree hierarchy and expose their attributes under each clock directry as below: omap:~# tree -d -L 2 /debug/clock/omap_32k_fck/ /debug/clock/omap_32k_fck/ |-- gpt10_fck |-- gpt11_fck |-- gpt1_fck |-- per_32k_alwon_fck | |-- gpio2_fck | |-- gpio3_fck | |-- gpio4_fck | |-- gpio5_fck | |-- gpio6_fck | `-- wdt3_fck |-- ts_fck `-- wkup_32k_fck |-- gpio1_fck `-- wdt2_fck 14 directories omap:~# tree /debug/clock/omap_32k_fck/gpt10_fck/ /debug/clock/omap_32k_fck/gpt10_fck/ |-- flags |-- rate `-- usecount 0 directories, 3 files Although, compared with David Brownell's small patch, this may look bit overkilling, I expect that this debugfs can deal with other PRCM complexities at the same time. For example, powerdomain dependencies can be expressed by using symbolic links of these clocks if powerdomain supports dubgfs as well. Signed-off-by: Hiroshi DOYU <Hiroshi.DOYU@nokia.com> Signed-off-by: Tony Lindgren <tony@atomide.com>
2008-07-03ARM: OMAP: Clean up interrupt lines to fix warnings for multi-omapTony Lindgren7-59/+64
If boards with different NR_IRQS are compiled together, tons of compiler warnings are emitted about redefining NR_IRQS. This patch fixes the problem by adding up NR_IRQS in a common place. Patch also removes quite a bit of now unnecessary code. Signed-off-by: Tony Lindgren <tony@atomide.com>
2008-07-03ARM: OMAP: McBSP: Add support for mcbsp on mach-omap2Eduardo Valentin3-10/+230
This patch adds support for mach-omap2 based on current mcbsp platform driver. Signed-off-by: Eduardo Valentin <eduardo.valentin@indt.org.br> Signed-off-by: Tony Lindgren <tony@atomide.com>
2008-07-03ARM: OMAP: McBSP: Add support for mcbsp on mach-omap1Eduardo Valentin3-10/+302
This patch adds support for mach-omap1 based on current mcbsp platform driver. Signed-off-by: Eduardo Valentin <eduardo.valentin@indt.org.br> Signed-off-by: Tony Lindgren <tony@atomide.com>
2008-07-03ARM: OMAP: McBSP: Prepare for splitting into omap1 and omap2 codeEduardo Valentin3-411/+361
This patch transform mcbsp code to use platform data from arch/arm/plat-omap/devices.c It also gets ride of ifdefs on mcbsp.c code. To do it, a platform data structure was defined. Signed-off-by: Eduardo Valentin <eduardo.valentin@indt.org.br> Signed-off-by: Tony Lindgren <tony@atomide.com>
2008-07-03ARM: OMAP: McBSP: Coding style cleanup on arch/arm/plat-omap/mcbsp.cEduardo Valentin1-95/+102
This patch fix lots of warnings and errors reported by scripts/checkpatch.pl on arch/arm/plat-omap/mcbsp.c. Signed-off-by: Eduardo Valentin <eduardo.valentin@indt.org.br> Acked-by: Felipe Balbi <felipe.balbi@nokia.com> Signed-off-by: Tony Lindgren <tony@atomide.com>
2008-07-03ARM: OMAP: SRAM: Split sram24xx.S into sram242x.S and sram243x.STony Lindgren9-104/+604
Split sram24xx.S into sram242x.S and sram243x.S Signed-off-by: Tony Lindgren <tony@atomide.com>
2008-07-03ARM: OMAP: SRAM: Move omap2 sram-fn.S to sram242x.STony Lindgren2-1/+1
This file will get split between sram242x.S and sram243x.S in following patch. Signed-off-by: Tony Lindgren <tony@atomide.com>
2008-07-03ARM: OMAP: SRAM: Move sram-fn.S from plat-omap to mach-omap1Tony Lindgren3-2/+2
This file is omap1 specific. Signed-off-by: Tony Lindgren <tony@atomide.com>
2008-07-03ARM: OMAP: DMA: Clean-up codeTony Lindgren2-181/+235
DMA clean-up, mostly checkpatch.pl fixes. Signed-off-by: Tony Lindgren <tony@atomide.com>
2008-07-03ARM: OMAP: DMA: Remove __REG accessTony Lindgren3-305/+450
Remove __REG access in DMA code, use dma_read/write instead: - dynamically set the omap_dma_base based on the omap type - omap_read/write becomes dma_read/write - dma channel registers are read with dma_ch_read/write Cc: David Brownell <david-b@pacbell.net> Cc: linux-usb@vger.kernel.org Signed-off-by: Tony Lindgren <tony@atomide.com>
2008-07-03ARM: OMAP: DMA: Make channels dynamic for multi-bootTony Lindgren2-25/+44
Make DMA channels dynamic for multi-boot Signed-off-by: Tony Lindgren <tony@atomide.com>
2008-07-03ARM: OMAP: Add OMAP3430 base definesPaul Walmsley2-0/+73
Add symbolic constants for OMAP3430 base addresses; include that file in hardware.h. Signed-off-by: Paul Walmsley <paul@pwsan.com> Signed-off-by: Tony Lindgren <tony@atomide.com>
2008-07-03ARM: OMAP: DMTimer: Optimize by adding load and startRichard Woodruff3-7/+22
This patch optimizes the timer load and start sequence. By combining the load and start a needless posted wait can be removed from the system timer execution path. * Before patch register writes are taking up .078% @ 500MHz during idle. Address |total |min |max |avr |count|ratio% old\process\default_idle|7.369s |0.0us|999.902ms|14.477ms|509. |62.661% ld\Global\cpu_v7_do_idle|4.265s |0.0us|375.786ms|24.374ms|175. |36.270% (UNKNOWN)|17.503ms|0.us|531.080us|5.119us|3419. |0.148% r\omap_dm_timer_set_load|8.135ms|0.0us|79.887us|15.065us|540. |0.069% <-- \vmlinux-old\Global\_end|2.023ms|0.0us|4.000us|0.560us|3613. |0.017% -old\Global\__raw_readsw|1.962ms|0.0us|108.610us|9.167us|214. |0.016% old\smc91x\smc_interrupt|1.353ms|0.0us|10.212us|2.348us|576. |0.011% s/namei\__link_path_walk|1.161ms|0.0us|4.310us|0.762us| 1524. |0.009% \omap_dm_timer_write_reg|1.085ms|0.0us|126.150us|2.153us|504. |0.009% <-- * After patch timer functions do not show up in top listings for long captures. Signed-off-by: Richard Woodruff <r-woodruff2@ti.com> Signed-off-by: Tony Lindgren <tony@atomide.com>
2008-07-03ARM: OMAP: DMTimer: Use posted modeRichard Woodruff1-42/+151
This patch adds the use of write posting for the timer. Previously, every write could lock the requestor for almost 3x32KHz cycles. This patch only synchronizes before writes and reads instead of after them and it does it on per register basis. Doing it this way there is some chance to hide some of the sync latency. It also removes some needless reads when non-posted mode is there. With out this fix the read/writes take almost 2% CPU load @500MHz just waiting on tick timer registers. Also define new 34xx only registers. Signed-off-by: Richard Woodruff <r-woodruff2@ti.com> Signed-off-by: Tony Lindgren <tony@atomide.com>
2008-07-03ARM: OMAP: Correcting the gpmc prefetch control register addressThara Gopinath0-0/+0
Correcting the GPMC_PREFETCH_CONTROL register address Signed-off-by: Thara Gopinath <thara@ti.com> Signed-off-by: Tony Lindgren <tony@atomide.com>
2008-07-03ARM: OMAP: DMA: Don't mark channel active in omap_enable_channel_irqJarkko Nikula0-0/+0
Channel should be marked active only when DMA is really started. Otherwise just omap_request_dma, omap_dma_link_lch and omap_dma_unlink_lch will cause incorrect dump_stack(). Signed-off-by: Jarkko Nikula <jarkko.nikula@nokia.com> Signed-off-by: Tony Lindgren <tony@atomide.com>
2008-07-03Merge branch 'for-linus' of ↵Linus Torvalds5-16/+63
git://git.kernel.org/pub/scm/linux/kernel/git/jbarnes/pci-2.6 * 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jbarnes/pci-2.6: PCI: acpiphp: cleanup notify handler on all root bridges PCI: Limit VPD read/write lengths for Broadcom 5706, 5708, 5709 rev. PCI: Restrict VPD read permission to root
2008-07-03Merge branch 'i2c-fix' of git://aeryn.fluff.org.uk/bjdooks/linuxLinus Torvalds1-14/+14
* 'i2c-fix' of git://aeryn.fluff.org.uk/bjdooks/linux: I2C: S3C2410: Add MODULE_ALIAS() for s3c2440 device. I2C: S3C2410: Fixup error codes returned rom a transfer. I2C: S3C2410: Check ACK on byte transmission
2008-07-03Merge branch 'for-2.6.26' of git://git.kernel.dk/linux-2.6-blockLinus Torvalds3-5/+11
* 'for-2.6.26' of git://git.kernel.dk/linux-2.6-block: Properly notify block layer of sync writes block: Fix the starving writes bug in the anticipatory IO scheduler
2008-07-03Merge branch 'release' of ↵Linus Torvalds2-1/+3
git://git.kernel.org/pub/scm/linux/kernel/git/aegl/linux-2.6 * 'release' of git://git.kernel.org/pub/scm/linux/kernel/git/aegl/linux-2.6: [IA64] export account_system_vtime [IA64] Bugfix for system with 32 cpus
2008-07-03Merge git://git.kernel.org/pub/scm/linux/kernel/git/mchehab/v4l-dvbLinus Torvalds12-0/+6885
* git://git.kernel.org/pub/scm/linux/kernel/git/mchehab/v4l-dvb: V4L/DVB (8178): uvc: Fix compilation breakage for the other drivers, if uvc is selected V4L/DVB (8145a): USB Video Class driver
2008-07-03Merge git://git.kernel.org/pub/scm/linux/kernel/git/bart/ide-2.6Linus Torvalds4-1/+99
* git://git.kernel.org/pub/scm/linux/kernel/git/bart/ide-2.6: ide: fix /proc/ide/ide?/mate reporting Revert "BAST: Remove old IDE driver"
2008-07-03Merge master.kernel.org:/home/rmk/linux-2.6-armLinus Torvalds6-25/+40
* master.kernel.org:/home/rmk/linux-2.6-arm: [ARM] 5131/1: Annotate platform_secondary_init with trace_hardirqs_off [ARM] 5117/1: pxafb: fix __devinit/exit annotations [ARM] Export dma_sync_sg_for_device() [ARM] 5109/1: Mark rtc sa1100 driver as wakeup source before registering it [ARM] 5116/1: pxafb: cleanup and fix order of failure handling [ARM] 5115/1: pxafb: fix ifdef for command line option handling ARM: OMAP: Correcting the gpmc prefetch control register address ARM: OMAP: DMA: Don't mark channel active in omap_enable_channel_irq
2008-07-03tty: Fix inverted logic in send_breakAlan Cox1-1/+1
Not sure how this came to get inverted but it appears to have been my mess up. Signed-off-by: Alan Cox <alan@redhat.com> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2008-07-03Merge branch 'sched-fixes-for-linus' of ↵Linus Torvalds1-0/+3
git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip * 'sched-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip: sched: fix divide error when trying to configure rt_period to zero
2008-07-03Merge branch 'i2c-for-linus' of git://jdelvare.pck.nerim.net/jdelvare-2.6Linus Torvalds2-5/+15
* 'i2c-for-linus' of git://jdelvare.pck.nerim.net/jdelvare-2.6: i2c: Fix bad hint about irqs in i2c.h i2c: Documentation: fix device matching description
2008-07-03Merge branch 'core-fixes-for-linus' of ↵Linus Torvalds1-1/+15
git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip * 'core-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip: rcu: fix hotplug vs rcu race
2008-07-03Merge branch 'x86-fixes-for-linus' of ↵Linus Torvalds1-2/+2
git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip * 'x86-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip: x86: fix NODES_SHIFT Kconfig range
2008-07-03Merge git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi-rc-fixes-2.6Linus Torvalds2-3/+21
* git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi-rc-fixes-2.6: [SCSI] esp: tidy up target reference counting [SCSI] esp: Fix OOPS in esp_reset_cleanup(). [SCSI] ses: Fix timeout
2008-07-03Merge git://git.kernel.org/pub/scm/linux/kernel/git/agk/linux-2.6-dmLinus Torvalds1-0/+1
* git://git.kernel.org/pub/scm/linux/kernel/git/agk/linux-2.6-dm: dm crypt: use cond_resched
2008-07-03Merge branch 'for-2.6.26' of git://neil.brown.name/mdLinus Torvalds3-3/+12
* 'for-2.6.26' of git://neil.brown.name/md: Fix error paths if md_probe fails. Don't acknowlege that stripe-expand is complete until it really is. Ensure interrupted recovery completed properly (v1 metadata plus bitmap)
2008-07-03Merge branch 'merge' of ↵Linus Torvalds3-2/+20
git://git.kernel.org/pub/scm/linux/kernel/git/paulus/powerpc * 'merge' of git://git.kernel.org/pub/scm/linux/kernel/git/paulus/powerpc: powerpc/mpc5200: Fix lite5200b suspend/resume powerpc/legacy_serial: Bail if reg-offset/shift properties are present powerpc/bootwrapper: update for initrd with simpleImage
2008-07-03Merge git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-2.6Linus Torvalds76-272/+411
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-2.6: (55 commits) net: fib_rules: fix error code for unsupported families netdevice: Fix wrong string handle in kernel command line parsing net: Tyop of sk_filter() comment netlink: Unneeded local variable net-sched: fix filter destruction in atm/hfsc qdisc destruction net-sched: change tcf_destroy_chain() to clear start of filter list ipv4: fix sysctl documentation of time related values mac80211: don't accept WEP keys other than WEP40 and WEP104 hostap: fix sparse warnings hostap: don't report useless WDS frames by default textsearch: fix Boyer-Moore text search bug netfilter: nf_conntrack_tcp: fixing to check the lower bound of valid ACK ipv6 route: Convert rt6_device_match() to use RT6_LOOKUP_F_xxx flags. netlabel: Fix a problem when dumping the default IPv6 static labels net/inet_lro: remove setting skb->ip_summed when not LRO-able inet fragments: fix race between inet_frag_find and inet_frag_secret_rebuild CONNECTOR: add a proc entry to list connectors netlink: Fix some doc comments in net/netlink/attr.c tcp: /proc/net/tcp rto,ato values not scaled properly (v2) include/linux/netdevice.h: don't export MAX_HEADER to userspace ...
2008-07-03DRM/i915: only use tiled blits on 965+Jesse Barnes1-2/+2
When scheduled swaps occur, we need to blit between front & back buffers. If the buffers are tiled, we need to set the appropriate XY_SRC_COPY tile bit, but only on 965 chips, since it will cause corruption on pre-965 (e.g. 945). Bug reported by and fix tested by Tomas Janousek <tomi@nomi.cz>. Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org> Acked-by: Dave Airlie <airlied@linux.ie> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2008-07-03drivers/input/ff-core.c needs <linux/sched.h>Geert Uytterhoeven1-0/+1
Commit 656acd2bbc4ce7f224de499ee255698701396c48 ("Input: fix locking in force-feedback core") causes the following regression on m68k: | linux/drivers/input/ff-core.c: In function 'input_ff_upload': | linux/drivers/input/ff-core.c:172: error: dereferencing pointer to incomplete type | linux/drivers/input/ff-core.c: In function 'erase_effect': | linux/drivers/input/ff-core.c:197: error: dereferencing pointer to incomplete type | linux/drivers/input/ff-core.c:204: error: dereferencing pointer to incomplete type | make[4]: *** [drivers/input/ff-core.o] Error 1 As the incomplete type is `struct task_struct', including <linux/sched.h> fixes it. Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org> Acked-by: Dmitry Torokhov <dmitry.torokhov@gmail.com> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2008-07-03Merge branch 'for-2.6.26' of git://git.secretlab.ca/git/linux-2.6-mpc52xx ↵Paul Mackerras1-1/+13
into merge
2008-07-02PCI: acpiphp: cleanup notify handler on all root bridgesAlex Chiang1-3/+14
During the development of the physical PCI slot patch series, Gary Hade kept on reporting strange oopses due to interactions between pci_slot and acpiphp. http://lkml.org/lkml/2007/11/28/319 find_root_bridges() unconditionally installs handle_hotplug_event_bridge() as an ACPI_SYSTEM_NOTIFY handler for all root bridges. However, during module cleanup, remove_bridge() will only remove the notify handler iff the root bridge had a hot-pluggable slot directly underneath. That is: root bridge -> hotplug slot But, if the topology looks like either of the following: root bridge -> non-hotplug slot root bridge -> p2p bridge -> hotplug slot Then we currently do not remove the notify handler from that root bridge. This can cause a kernel oops if we modprobe acpiphp later and it gets loaded somewhere else in memory. If the root bridge then receives a hotplug event, it will then attempt to call a stale, non-existent notify handler and we blow up. Much thanks goes to Gary Hade for his persistent debugging efforts. Signed-off-by: Alex Chiang <achiang@hp.com> Signed-off-by: Gary Hade <garyhade@us.ibm.com> Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
2008-07-02PCI: Limit VPD read/write lengths for Broadcom 5706, 5708, 5709 rev.Benjamin Li4-12/+48
For Broadcom 5706, 5708, 5709 rev. A nics, any read beyond the VPD end tag will hang the device. This problem was initially observed when a vpd entry was created in sysfs ('/sys/bus/pci/devices/<id>/vpd'). A read to this sysfs entry will dump 32k of data. Reading a full 32k will cause an access beyond the VPD end tag causing the device to hang. Once the device is hung, the bnx2 driver will not be able to reset the device. We believe that it is legal to read beyond the end tag and therefore the solution is to limit the read/write length. A majority of this patch is from Matthew Wilcox who gave code for reworking the PCI vpd size information. A PCI quirk added for the Broadcom NIC's to limit the read/write's. Signed-off-by: Benjamin Li <benli@broadcom.com> Signed-off-by: Matthew Wilcox <willy@linux.intel.com> Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
2008-07-02V4L/DVB (8178): uvc: Fix compilation breakage for the other drivers, if uvc ↵Mauro Carvalho Chehab1-1/+1
is selected UVC makefile defines obj as: obj-$(CONFIG_USB_VIDEO_CLASS) := uvcvideo.o Instead of: obj-$(CONFIG_USB_VIDEO_CLASS) += uvcvideo.o Due to that, if uvc is selected, all obj-y or obj-m that were added to compilation were forget. This breaks a proper kernel build. Acked-by: Laurent Pinchart <laurent.pinchart@skynet.be> Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
2008-07-02dm crypt: use cond_reschedMilan Broz1-0/+1
Add cond_resched() to prevent monopolising CPU when processing large bios. dm-crypt processes encryption of bios in sector units. If the bio request is big it can spend a long time in the encryption call. Signed-off-by: Milan Broz <mbroz@redhat.com> Tested-by: Yan Li <elliot.li.tech@gmail.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Alasdair G Kergon <agk@redhat.com>
2008-07-02net: fib_rules: fix error code for unsupported familiesPatrick McHardy1-2/+2
The errno code returned must be negative. Fixes "RTNETLINK answers: Unknown error 18446744073709551519". Signed-off-by: Patrick McHardy <kaber@trash.net> Signed-off-by: David S. Miller <davem@davemloft.net>
generated by cgit v1.2.3 (git 2.39.0) at 2024-11-20 02:40:53 +0300