| Age | Commit message (Collapse) | Author | Files | Lines |
|---|
|
The initial control port tx status patch assumed, that
we have IEEE 802.11 frames, but actually ethernet frames
are stored in the ack skb. Fix this by checking for the
correct ethertype and skb protocol 802.3.
Also allow tx status reports for ETH_P_PREAUTH, as preauth
frames can also be send over the nl80211 control port.
Fixes: a7528198add8 ("mac80211: support control port TX status reporting")
Reported-by: Jouni Malinen <j@w1.fi>
Signed-off-by: Markus Theil <markus.theil@tu-ilmenau.de>
Reported-by: kernel test robot <lkp@intel.com>
Link: https://lore.kernel.org/r/20200622123542.173695-1-markus.theil@tu-ilmenau.de
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
|
|
Add the definitions for missing AKM selectors defined in
IEEE P802.11-REVmd/D3.0, table 9-151. These definitions will
be used by various drivers that support these new AKM suites.
Signed-off-by: Veerendranath Jakkam <vjakkam@codeaurora.org>
Link: https://lore.kernel.org/r/20200617113132.13477-1-vjakkam@codeaurora.org
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
|
|
Doug Berger says:
====================
net: bcmgenet: use hardware padding of runt frames
Now that scatter-gather and tx-checksumming are enabled by default
it revealed a packet corruption issue that can occur for very short
fragmented packets.
When padding these frames to the minimum length it is possible for
the non-linear (fragment) data to be added to the end of the linear
header in an SKB. Since the number of fragments is read before the
padding and used afterward without reloading, the fragment that
should have been consumed can be tacked on in place of part of the
padding.
The third commit in this set corrects this by removing the software
padding and allowing the hardware to add the pad bytes if necessary.
The first two commits resolve warnings observed by the kbuild test
robot and are included here for simplicity of application.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
When commit 474ea9cafc45 ("net: bcmgenet: correctly pad short
packets") added the call to skb_padto() it should have been
located before the nr_frags parameter was read since that value
could be changed when padding packets with lengths between 55
and 59 bytes (inclusive).
The use of a stale nr_frags value can cause corruption of the
pad data when tx-scatter-gather is enabled. This corruption of
the pad can cause invalid checksum computation when hardware
offload of tx-checksum is also enabled.
Since the original reason for the padding was corrected by
commit 7dd399130efb ("net: bcmgenet: fix skb_len in
bcmgenet_xmit_single()") we can remove the software padding all
together and make use of hardware padding of short frames as
long as the hardware also always appends the FCS value to the
frame.
Fixes: 474ea9cafc45 ("net: bcmgenet: correctly pad short packets")
Signed-off-by: Doug Berger <opendmb@gmail.com>
Acked-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The 16-bit value that holds a short in network byte order should
be declared as a restricted big endian type to allow type checks
to succeed during assignment.
Fixes: 3e370952287c ("net: bcmgenet: add support for ethtool rxnfc flows")
Reported-by: kbuild test robot <lkp@intel.com>
Signed-off-by: Doug Berger <opendmb@gmail.com>
Acked-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This function was originally removed by Baoyou Xie in
commit e2072600a241 ("net: bcmgenet: remove unused function in
bcmgenet.c") to prevent a build warning.
Some of the functions removed by Baoyou Xie are now used for
WAKE_FILTER support so his commit was reverted, but this function
is still unused and the kbuild test robot dutifully reported the
warning.
This commit once again removes the remaining unused hfb functions.
Fixes: 14da1510fedc ("Revert "net: bcmgenet: remove unused function in bcmgenet.c"")
Reported-by: kbuild test robot <lkp@intel.com>
Signed-off-by: Doug Berger <opendmb@gmail.com>
Acked-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The error DBG_STATUS_NO_MATCHING_FRAMING_MODE was added to the enum
enum dbg_status however there is a missing corresponding entry for
this in the array s_status_str. This causes an out-of-bounds read when
indexing into the last entry of s_status_str. Fix this by adding in
the missing entry.
Addresses-Coverity: ("Out-of-bounds read").
Fixes: 2d22bc8354b1 ("qed: FW 8.42.2.0 debug features")
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Jisheng Zhang says:
====================
net: phy: call phy_disable_interrupts() in phy_init_hw()
We face an issue with rtl8211f, a pin is shared between INTB and PMEB,
and the PHY Register Accessible Interrupt is enabled by default, so
the INTB/PMEB pin is always active in polling mode case.
As Heiner pointed out "I was thinking about calling
phy_disable_interrupts() in phy_init_hw(), to have a defined init
state as we don't know in which state the PHY is if the PHY driver is
loaded. We shouldn't assume that it's the chip power-on defaults, BIOS
or boot loader could have changed this. Or in case of dual-boot
systems the other OS could leave the PHY in whatever state."
patch1 makes phy_disable_interrupts() non-static so that it could be used
in phy_init_hw() to have a defined init state.
patch2 calls phy_disable_interrupts() in phy_init_hw() to have a
defined init state.
Since v3:
- call phy_disable_interrupts() have interrupts disabled first then
config_init, thank Florian
Since v2:
- Don't export phy_disable_interrupts() but just make it non-static
Since v1:
- EXPORT the correct symbol
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Call phy_disable_interrupts() in phy_init_hw() to "have a defined init
state as we don't know in which state the PHY is if the PHY driver is
loaded. We shouldn't assume that it's the chip power-on defaults, BIOS
or boot loader could have changed this. Or in case of dual-boot
systems the other OS could leave the PHY in whatever state." as pointed
out by Heiner.
Suggested-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: Jisheng Zhang <Jisheng.Zhang@synaptics.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
We face an issue with rtl8211f, a pin is shared between INTB and PMEB,
and the PHY Register Accessible Interrupt is enabled by default, so
the INTB/PMEB pin is always active in polling mode case.
As Heiner pointed out "I was thinking about calling
phy_disable_interrupts() in phy_init_hw(), to have a defined init
state as we don't know in which state the PHY is if the PHY driver is
loaded. We shouldn't assume that it's the chip power-on defaults, BIOS
or boot loader could have changed this. Or in case of dual-boot
systems the other OS could leave the PHY in whatever state."
Make phy_disable_interrupts() non-static so that it could be used in
phy_init_hw() to have a defined init state.
Suggested-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: Jisheng Zhang <Jisheng.Zhang@synaptics.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
When writing the serdes configuration register was moved to
mvneta_config_interface() the whole code block was removed from
mvneta_port_power_up() in the assumption that its only purpose was to
write the serdes configuration register. As mentioned by Russell King
its purpose was also to check for valid interface modes early so that
later in the driver we do not have to care for unexpected interface
modes.
Add back the test to let the driver bail out early on unhandled
interface modes.
Fixes: b4748553f53f ("net: ethernet: mvneta: Fix Serdes configuration for SoCs without comphy")
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Reviewed-by: Russell King <rmk+kernel@armlinux.org.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
In mvneta_config_interface() the RGMII modes are catched by the default
case which is an error return. The RGMII modes are valid modes for the
driver, so instead of returning an error add a break statement to return
successfully.
This avoids this warning for non comphy SoCs which use RGMII, like
SolidRun Clearfog:
WARNING: CPU: 0 PID: 268 at drivers/net/ethernet/marvell/mvneta.c:3512 mvneta_start_dev+0x220/0x23c
Fixes: b4748553f53f ("net: ethernet: mvneta: Fix Serdes configuration for SoCs without comphy")
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Reviewed-by: Russell King <rmk+kernel@armlinux.org.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The driver for Marvell switches puts all ports in IGMP snooping mode
which results in all IGMP/MLD frames that ingress on the ports to be
forwarded to the CPU only.
The bridge code in the kernel can then interpret these frames and act
upon them, for instance by updating the mdb in the switch to reflect
multicast memberships of stations connected to the ports. However,
the IGMP/MLD frames must then also be forwarded to other ports of the
bridge so external IGMP queriers can track membership reports, and
external multicast clients can receive query reports from foreign IGMP
queriers.
Currently, this is impossible as the EDSA tagger sets offload_fwd_mark
on the skb when it unwraps the tagged frames, and that will make the
switchdev layer prevent the skb from egressing on any other port of
the same switch.
To fix that, look at the To_CPU code in the DSA header and make
forwarding of the frame possible for trapped IGMP packets.
Introduce some #defines for the frame types to make the code a bit more
comprehensive.
This was tested on a Marvell 88E6352 variant.
Signed-off-by: Daniel Mack <daniel@zonque.org>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Tested-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
execute_check_pkt_len
ovs connection tracking module performs de-fragmentation on incoming
fragmented traffic. Take info account if traffic has been de-fragmented
in execute_check_pkt_len action otherwise we will perform the wrong
nested action considering the original packet size. This issue typically
occurs if ovs-vswitchd adds a rule in the pipeline that requires connection
tracking (e.g. OVN stateful ACLs) before execute_check_pkt_len action.
Moreover take into account GSO fragment size for GSO packet in
execute_check_pkt_len routine
Fixes: 4d5ec89fc8d14 ("net: openvswitch: Add a new action check_pkt_len")
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Russell King says:
====================
Two phylink pause fixes
While testing, I discovered two issues with ethtool -A with phylink.
First, if there is a PHY bound to the network device, we hit a
deadlock when phylib tries to notify us of the link changing as a
result of triggering a renegotiation.
Second, when we are manually forcing the pause settings, and there
is no renegotiation triggered, we do not update the MAC via the new
mac_link_up approach.
These two patches solve both problems, and will need to be backported
to v5.7; they do not apply cleanly there due to the introduction of
PCS in the v5.8 merge window.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
We have been relying on link events and mac_config() when the manual
pause modes are changed. With recent developments, such as moving
the programming of link state to mac_link_up(), this no longer works.
To ensure that we update the MAC, we must generate a link-down followed
by a link-up event; we can do that by setting mac_link_dropped and
triggering a resolve.
Fixes: 91a208f2185a ("net: phylink: propagate resolved link config via mac_link_up()")
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Fix a phylink's ethtool set_pauseparam support deadlock caused by phylib
interacting with phylink: we must not hold the state lock while calling
phylib functions that may call into phylink_phy_change().
Fixes: f904f15ea9b5 ("net: phylink: allow ethtool -A to change flow control advertisement")
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Clearing the sock TX queue in sk_set_socket() might cause unexpected
out-of-order transmit when called from sock_orphan(), as outstanding
packets can pick a different TX queue and bypass the ones already queued.
This is undesired in general. More specifically, it breaks the in-order
scheduling property guarantee for device-offloaded TLS sockets.
Remove the call to sk_tx_queue_clear() in sk_set_socket(), and add it
explicitly only where needed.
Fixes: e022f0b4a03f ("net: Introduce sk_tx_queue_mapping")
Signed-off-by: Tariq Toukan <tariqt@mellanox.com>
Reviewed-by: Boris Pismenny <borisp@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
A last minute change put the TDR cable test parameters into a nest.
The validation is not sufficient, resulting in an oops if the nest is
missing. Set default values first, then update them if the nest is
provided.
Fixes: f2bc8ad31a7f ("net: ethtool: Allow PHY cable test TDR data to configured")
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Michael Chan says:
====================
bnxt_en: Bug fixes.
The first patch stores the firmware version code which is needed by the
next 2 patches to determine some worarounds based on the firmware version.
The workarounds are to disable legacy TX push mode and to clear the
hardware statistics during ifdown. The last patch checks that it is
a PF before reading the VPD.
Please also queue these for -stable. Thanks.
====================
Reviewed-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Virtual functions does not have VPD information. This patch modifies
calling bnxt_read_vpd_info() only for PFs and avoids an unnecessary
error log.
Fixes: a0d0fd70fed5 ("bnxt_en: Read partno and serialno of the board from VPD")
Signed-off-by: Vasundhara Volam <vasundhara-v.volam@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
On older firmware, the hardware statistics are not cleared when the
driver frees the hardware stats contexts during ifdown. The driver
expects these stats to be cleared and saves a copy before freeing
the stats contexts. During the next ifup, the driver will likely
allocate the same hardware stats contexts and this will cause a big
increase in the counters as the old counters are added back to the
saved counters.
We fix it by making an additional firmware call to clear the counters
before freeing the hw stats contexts when the firmware is the older
20.x firmware.
Fixes: b8875ca356f1 ("bnxt_en: Save ring statistics before reset.")
Reported-by: Jakub Kicinski <kicinski@fb.com>
Reviewed-by: Vasundhara Volam <vasundhara-v.volam@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Tested-by: Jakub Kicinski <kicinski@fb.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Older firmware may not support legacy TX push properly and may not
be disabling it. So we check certain firmware versions that may
have this problem and disable legacy TX push unconditionally.
Fixes: c0c050c58d84 ("bnxt_en: New Broadcom ethernet driver.")
Reviewed-by: Edwin Peer <edwin.peer@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
We currently only store the firmware version as a string for ethtool
and devlink info. Store it also as a version code. The next 2
patches will need to check the firmware major version to determine
some workarounds.
We also use the 16-bit firmware version fields if the firmware is newer
and provides the 16-bit fields.
Reviewed-by: Edwin Peer <edwin.peer@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Rahul Lakkireddy says:
====================
cxgb4/cxgb4vf: fix warnings reported by sparse
This series of patches fix various warnings reported by the sparse
tool.
Patches 1 and 2 fix lock context imbalance warnings.
Patch 3 fixes cast to restricted __be64 warning when fetching
timestamp in PTP path.
Patch 4 fixes several cast to restricted __be32 warnings in TC-U32
offload parser.
Patch 5 fixes several cast from restricted __be16 warnings in parsing
L4 ports for filters.
Patch 6 fixes several restricted __be32 degrades to integer warnings
when comparing IP address masks for exact-match filters.
Patch 7 fixes cast to restricted __be64 warning when fetching SGE
queue contexts in device dump collection.
Patch 8 fixes cast from restricted __sum16 warning when saving IPv4
partial checksum.
Patch 9 fixes issue with string array scope in DCB path.
Patch 10 fixes a set but unused variable warning when DCB is disabled.
Patch 11 fixes several kernel-doc comment warnings in cxgb4 driver.
Patch 12 fixes several kernel-doc comment warnings in cxgb4vf driver.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Update several kernel-doc line comments to fix warnings reported by
make W=1.
Fixes following class of warnings reported by make W=1 in several
places:
cxgb4vf_main.c:275: warning: Function parameter or member 'persistent'
not described in 'cxgb4vf_change_mac'
cxgb4vf_main.c:275: warning: Excess function parameter 'persist'
description in 'cxgb4vf_change_mac'
Fixes: 16f8bd4be754 ("cxgb4vf: Add core T4 PCI-E SR-IOV Virtual Function hardware definitions and device communication code")
Fixes: c6e0d91464da ("cxgb4vf: Add T4 Virtual Function Scatter-Gather Engine DMA code")
Fixes: e0a8b34a9cc4 ("cxgb4vf: Add and initialize some sge params for VF driver")
Fixes: c3168cabe1af ("cxgb4/cxgbvf: Handle 32-bit fw port capabilities")
Fixes: 0e23daeb6407 ("drivers/net: chelsio/cxgb*: Convert timers to use timer_setup()")
Fixes: 3f8cfd0d95e6 ("cxgb4/cxgb4vf: Program hash region for {t4/t4vf}_change_mac()")
Signed-off-by: Rahul Lakkireddy <rahul.lakkireddy@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Update several kernel-doc line comments to fix warnings reported by
make W=1.
Fixes following class of warnings reported by make W=1 in several
places:
l2t.c:616: warning: Cannot understand * @dev: net_device pointer
t4_hw.c:3175: warning: Function parameter or member 'adap' not
described in 't4_get_exprom_version'
t4_hw.c:3175: warning: Excess function parameter 'adapter' description
in 't4_get_exprom_version'
Fixes: 56d36be4dd5f ("cxgb4: Add HW and FW support code")
Fixes: fd3a47900b6f ("cxgb4: Add packet queues and packet DMA code")
Fixes: 26f7cbc0a5a4 ("cxgb4: Don't attempt to upgrade T4 firmware when cxgb4 will end up as a slave")
Fixes: 793dad94e745 ("RDMA/cxgb4: Fix bug for active and passive LE hash collision path")
Fixes: ba3f8cd55f2a ("cxgb4: Add support in cxgb4 to get expansion rom version via ethtool")
Fixes: f7502659cec8 ("cxgb4: Add API to alloc l2t entry; also update existing ones")
Fixes: ddc7740d9a7c ("cxgb4: Decode link down reason code obtained from firmware")
Fixes: 193c4c2845f7 ("cxgb4: Update T6 Buffer Group and Channel Mappings")
Fixes: 8f46d46715a1 ("cxgb4: Use Firmware params to get buffer-group map")
Fixes: a456950445a0 ("cxgb4: time stamping interface for PTP")
Fixes: 9c33e4208bce ("cxgb4: Add PTP Hardware Clock (PHC) support")
Fixes: c3168cabe1af ("cxgb4/cxgbvf: Handle 32-bit fw port capabilities")
Fixes: 5ccf9d049615 ("cxgb4: update API for TP indirect register access")
Fixes: 3bdb376e6944 ("cxgb4: introduce SMT ops to prepare for SMAC rewrite support")
Fixes: 736c3b94474e ("cxgb4: collect egress and ingress SGE queue contexts")
Fixes: f56ec6766dcf ("cxgb4: Add support for ethtool i2c dump")
Fixes: 9d5fd927d20b ("cxgb4/cxgb4vf: add support for ndo_set_vf_vlan")
Fixes: 98f3697f8d41 ("cxgb4: add tc flower match support for tunnel VNI")
Fixes: 02d805dc5fe3 ("cxgb4: use new fw interface to get the VIN and smt index")
Fixes: 3f8cfd0d95e6 ("cxgb4/cxgb4vf: Program hash region for {t4/t4vf}_change_mac()")
Fixes: d429005fdf2c ("cxgb4/cxgb4vf: Add support for SGE doorbell queue timer")
Fixes: 0e395b3cb1fb ("cxgb4: add FLOWC based QoS offload")
Signed-off-by: Rahul Lakkireddy <rahul.lakkireddy@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Remove the set but unused variable when DCB is disabled. Instead,
do the calculation directly inline.
Fixes following warning in make W=1:
cxgb4_main.c: In function 'cfg_queues':
cxgb4_main.c:5380:29: warning: variable 'n1g' set but not used
[-Wunused-but-set-variable]
u32 i, n10g = 0, qidx = 0, n1g = 0;
^
Fixes: 116ca924aea6 ("cxgb4: fix checks for max queues to allocate")
Signed-off-by: Rahul Lakkireddy <rahul.lakkireddy@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Move the DCB version string array extern to header file.
Fixes following sparse warning:
cxgb4_dcb.c:13:12: warning: symbol 'dcb_ver_array' was not declared.
Should it be static?
Fixes: ebddd97afb89 ("cxgb4: add support to display DCB info")
Signed-off-by: Rahul Lakkireddy <rahul.lakkireddy@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The checksum field in IPv4 header is in __sum16 and ip_fast_csum()
also returns __sum16. So, no need to cast it to u16.
Fixes following sparse warning:
sge.c:1539:47: warning: cast from restricted __sum16
sge.c:1539:44: warning: incorrect type in assignment (different base types)
sge.c:1539:44: expected restricted __sum16 [usertype] check
sge.c:1539:44: got unsigned short [usertype]
Fixes: d0a1299c6bf7 ("cxgb4: add support for vxlan segmentation offload")
Signed-off-by: Rahul Lakkireddy <rahul.lakkireddy@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The data in destination buffer is expected to be be parsed in big
endian. So, use the right context.
Fixes following sparse warning:
cudbg_lib.c:2041:44: warning: incorrect type in assignment (different
base types)
cudbg_lib.c:2041:44: expected unsigned long long [usertype]
cudbg_lib.c:2041:44: got restricted __be64 [usertype]
Fixes: 736c3b94474e ("cxgb4: collect egress and ingress SGE queue contexts")
Signed-off-by: Rahul Lakkireddy <rahul.lakkireddy@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Use correct type to check for all-mask exact match IP addresses.
Fixes following sparse warnings due to big endian value checks
against 0xffffffff in is_addr_all_mask():
cxgb4_filter.c:977:25: warning: restricted __be32 degrades to integer
cxgb4_filter.c:983:37: warning: restricted __be32 degrades to integer
cxgb4_filter.c:984:37: warning: restricted __be32 degrades to integer
cxgb4_filter.c:985:37: warning: restricted __be32 degrades to integer
cxgb4_filter.c:986:37: warning: restricted __be32 degrades to integer
Fixes: 3eb8b62d5a26 ("cxgb4: add support to create hash-filters via tc-flower offload")
Signed-off-by: Rahul Lakkireddy <rahul.lakkireddy@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The source and destination L4 ports in filter offload need to be
in CPU endian. They will finally be converted to Big Endian after
all operations are done and before giving them to hardware. The
L4 ports for NAT are expected to be passed as a byte stream TCB.
So, treat them as such.
Fixes following sparse warnings in several places:
cxgb4_tc_flower.c:159:33: warning: cast from restricted __be16
cxgb4_tc_flower.c:159:33: warning: incorrect type in argument 1 (different
base types)
cxgb4_tc_flower.c:159:33: expected unsigned short [usertype] val
cxgb4_tc_flower.c:159:33: got restricted __be16 [usertype] dst
Fixes: dca4faeb812f ("cxgb4: Add LE hash collision bug fix path in LLD driver")
Fixes: 62488e4b53ae ("cxgb4: add basic tc flower offload support")
Fixes: 557ccbf9dfa8 ("cxgb4: add tc flower support for L3/L4 rewrite")
Signed-off-by: Rahul Lakkireddy <rahul.lakkireddy@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
TC-U32 passes all keys values and masks in __be32 format. The parser
already expects this and hence pass the value and masks in __be32
natively to the parser.
Fixes following sparse warnings in several places:
cxgb4_tc_u32.c:57:21: warning: incorrect type in assignment (different base
types)
cxgb4_tc_u32.c:57:21: expected unsigned int [usertype] val
cxgb4_tc_u32.c:57:21: got restricted __be32 [usertype] val
cxgb4_tc_u32_parse.h:48:24: warning: cast to restricted __be32
Fixes: 2e8aad7bf203 ("cxgb4: add parser to translate u32 filters to internal spec")
Signed-off-by: Rahul Lakkireddy <rahul.lakkireddy@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Use get_unaligned_be64() to fetch the timestamp needed for ns_to_ktime()
conversion.
Fixes following sparse warning:
sge.c:3282:43: warning: cast to restricted __be64
Fixes: a456950445a0 ("cxgb4: time stamping interface for PTP")
Signed-off-by: Rahul Lakkireddy <rahul.lakkireddy@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Check for whether PTP is enabled or not at the caller and perform
locking/unlocking at the caller.
Fixes following sparse warning:
sge.c:1641:26: warning: context imbalance in 'cxgb4_eth_xmit' -
different lock contexts for basic block
Fixes: a456950445a0 ("cxgb4: time stamping interface for PTP")
Signed-off-by: Rahul Lakkireddy <rahul.lakkireddy@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Move code handling L2T ARP failures to the only caller.
Fixes following sparse warning:
skbuff.h:2091:29: warning: context imbalance in
'handle_failed_resolution' - unexpected unlock
Fixes: 749cb5fe48bb ("cxgb4: Replace arpq_head/arpq_tail with SKB double link-list code")
Signed-off-by: Rahul Lakkireddy <rahul.lakkireddy@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Alexander Lobakin says:
====================
net: qed/qede: various stability fixes
This set addresses several near-critical issues that were observed
and reproduced on different test and production configurations.
v2:
- don't split the "Fixes:" tag across several lines in patch 9;
- no functional changes.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Variable 'abs_ppfid' in qed_dev.c:qed_llh_add_mac_filter() always gets
printed, but is initialized only under 'ref_cnt == 1' condition. This
results in:
In file included from ./include/linux/kernel.h:15:0,
from ./include/asm-generic/bug.h:19,
from ./arch/x86/include/asm/bug.h:86,
from ./include/linux/bug.h:5,
from ./include/linux/io.h:11,
from drivers/net/ethernet/qlogic/qed/qed_dev.c:35:
drivers/net/ethernet/qlogic/qed/qed_dev.c: In function 'qed_llh_add_mac_filter':
./include/linux/printk.h:358:2: warning: 'abs_ppfid' may be used uninitialized
in this function [-Wmaybe-uninitialized]
printk(KERN_NOTICE pr_fmt(fmt), ##__VA_ARGS__)
^~~~~~
drivers/net/ethernet/qlogic/qed/qed_dev.c:983:17: note: 'abs_ppfid' was declared
here
u8 filter_idx, abs_ppfid;
^~~~~~~~~
...under W=1+.
Fix this by initializing it with zero.
Fixes: 79284adeb99e ("qed: Add llh ppfid interface and 100g support for offload protocols")
Signed-off-by: Alexander Lobakin <alobakin@marvell.com>
Signed-off-by: Igor Russkikh <irusskikh@marvell.com>
Signed-off-by: Michal Kalderon <michal.kalderon@marvell.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Sizes of all ILT blocks must be reset before ILT recomputing when
disabling clients, or memory allocation may exceed ILT shadow array
and provoke system crashes.
Fixes: 1408cc1fa48c ("qed: Introduce VFs")
Signed-off-by: Alexander Lobakin <alobakin@marvell.com>
Signed-off-by: Igor Russkikh <irusskikh@marvell.com>
Signed-off-by: Michal Kalderon <michal.kalderon@marvell.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Set edev->cdev pointer to NULL after calling remove() callback to avoid
using of already freed object.
Fixes: ccc67ef50b90 ("qede: Error recovery process")
Signed-off-by: Alexander Lobakin <alobakin@marvell.com>
Signed-off-by: Igor Russkikh <irusskikh@marvell.com>
Signed-off-by: Michal Kalderon <michal.kalderon@marvell.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Currently PTP cyclecounter and timecounter are initialized only on
the first probing and are cleaned up during removal. This means that
PTP becomes non-functional after device recovery.
Fix this by unconditional PTP initialization on probing and clearing
Tx pending bit on exiting.
Fixes: ccc67ef50b90 ("qede: Error recovery process")
Signed-off-by: Alexander Lobakin <alobakin@marvell.com>
Signed-off-by: Igor Russkikh <irusskikh@marvell.com>
Signed-off-by: Michal Kalderon <michal.kalderon@marvell.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This is likely a copy'n'paste mistake. The amount of ILT lines to
reserve for a single VF was being multiplied by the total VFs count.
This led to a huge redundancy in reservation and potential lines
drainouts.
Fixes: 1408cc1fa48c ("qed: Introduce VFs")
Signed-off-by: Alexander Lobakin <alobakin@marvell.com>
Signed-off-by: Igor Russkikh <irusskikh@marvell.com>
Signed-off-by: Michal Kalderon <michal.kalderon@marvell.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
25ms sleep cycles in waiting for PF response are excessive and may lead
to different timeout failures.
Start to wait with short udelays, and in most cases polling will end
here. If the time was not sufficient, switch to msleeps.
usleep_range() may go far beyond 100us depending on platform and tick
configuration, hence atomic udelays for consistency.
Also add explicit DMA barriers since 'done' always comes from a shared
request-response DMA pool, and note that in the comment nearby.
Fixes: 1408cc1fa48c ("qed: Introduce VFs")
Signed-off-by: Alexander Lobakin <alobakin@marvell.com>
Signed-off-by: Igor Russkikh <irusskikh@marvell.com>
Signed-off-by: Michal Kalderon <michal.kalderon@marvell.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Set rdma_wq pointer to NULL after destroying the workqueue and check
for it when adding new events to fix crashes on driver unload.
Fixes: cee9fbd8e2e9 ("qede: Add qedr framework")
Signed-off-by: Alexander Lobakin <alobakin@marvell.com>
Signed-off-by: Igor Russkikh <irusskikh@marvell.com>
Signed-off-by: Michal Kalderon <michal.kalderon@marvell.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
qed_spq_unregister_async_cb() should be called before
qed_rdma_info_free() to avoid crash-spawning uses-after-free.
Instead of calling it from each subsystem exit code, do it in one place
on PF down.
Fixes: 291d57f67d24 ("qed: Fix rdma_info structure allocation")
Signed-off-by: Alexander Lobakin <alobakin@marvell.com>
Signed-off-by: Igor Russkikh <irusskikh@marvell.com>
Signed-off-by: Michal Kalderon <michal.kalderon@marvell.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
qed_chain_get_element_left{,_u32} returned 0 when the difference
between producer and consumer page count was equal to the total
page count.
Fix this by conditional expanding of producer value (vs
unconditional). This allowed to eliminate normalizaton against
total page count, which was the cause of this bug.
Misc: replace open-coded constants with common defines.
Fixes: a91eb52abb50 ("qed: Revisit chain implementation")
Signed-off-by: Alexander Lobakin <alobakin@marvell.com>
Signed-off-by: Igor Russkikh <irusskikh@marvell.com>
Signed-off-by: Michal Kalderon <michal.kalderon@marvell.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Commit e585f2363637 ("udp: Changes to udp_offload to support remote
checksum offload") added new GSO type and a corresponding netdev
feature, but missed Ethtool's 'netdev_features_strings' table.
Give it a name so it will be exposed to userspace and become available
for manual configuration.
v3:
- decouple from "netdev_features_strings[] cleanup" series;
- no functional changes.
v2:
- don't split the "Fixes:" tag across lines;
- no functional changes.
Fixes: e585f2363637 ("udp: Changes to udp_offload to support remote checksum offload")
Signed-off-by: Alexander Lobakin <alobakin@pm.me>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Jason A. Donenfeld says:
====================
wireguard fixes for 5.8-rc3
This series contains two fixes, one cosmetic and one quite important:
1) Avoid the `if ((x = f()) == y)` pattern, from Frank
Werner-Krippendorf.
2) Mitigate a potential memory leak by creating circular netns
references, while also making the netns semantics a bit more
robust.
Patch (2) has a "Fixes:" line and should be backported to stable.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Before, we took a reference to the creating netns if the new netns was
different. This caused issues with circular references, with two
wireguard interfaces swapping namespaces. The solution is to rather not
take any extra references at all, but instead simply invalidate the
creating netns pointer when that netns is deleted.
In order to prevent this from happening again, this commit improves the
rough object leak tracking by allowing it to account for created and
destroyed interfaces, aside from just peers and keys. That then makes it
possible to check for the object leak when having two interfaces take a
reference to each others' namespaces.
Fixes: e7096c131e51 ("net: WireGuard secure network tunnel")
Signed-off-by: Jason A. Donenfeld <Jason@zx2c4.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
