diff options
Diffstat (limited to 'include/uapi/linux/nl80211.h')
| -rw-r--r-- | include/uapi/linux/nl80211.h | 152 |
1 files changed, 148 insertions, 4 deletions
diff --git a/include/uapi/linux/nl80211.h b/include/uapi/linux/nl80211.h index 47700a2b9af9..40832d13c2f1 100644 --- a/include/uapi/linux/nl80211.h +++ b/include/uapi/linux/nl80211.h @@ -757,7 +757,8 @@ * of any other interfaces, and other interfaces will again take * precedence when they are used. * - * @NL80211_CMD_SET_WDS_PEER: Set the MAC address of the peer on a WDS interface. + * @NL80211_CMD_SET_WDS_PEER: Set the MAC address of the peer on a WDS interface + * (no longer supported). * * @NL80211_CMD_SET_MULTICAST_TO_UNICAST: Configure if this AP should perform * multicast to unicast conversion. When enabled, all multicast packets @@ -1177,6 +1178,10 @@ * includes the contents of the frame. %NL80211_ATTR_ACK flag is included * if the recipient acknowledged the frame. * + * @NL80211_CMD_SET_SAR_SPECS: SAR power limitation configuration is + * passed using %NL80211_ATTR_SAR_SPEC. %NL80211_ATTR_WIPHY is used to + * specify the wiphy index to be applied to. + * * @NL80211_CMD_MAX: highest used command number * @__NL80211_CMD_AFTER_LAST: internal use */ @@ -1407,6 +1412,8 @@ enum nl80211_commands { NL80211_CMD_CONTROL_PORT_FRAME_TX_STATUS, + NL80211_CMD_SET_SAR_SPECS, + /* add new commands above here */ /* used to define NL80211_CMD_MAX below */ @@ -1750,8 +1757,9 @@ enum nl80211_commands { * specify just a single bitrate, which is to be used for the beacon. * The driver must also specify support for this with the extended * features NL80211_EXT_FEATURE_BEACON_RATE_LEGACY, - * NL80211_EXT_FEATURE_BEACON_RATE_HT and - * NL80211_EXT_FEATURE_BEACON_RATE_VHT. + * NL80211_EXT_FEATURE_BEACON_RATE_HT, + * NL80211_EXT_FEATURE_BEACON_RATE_VHT and + * NL80211_EXT_FEATURE_BEACON_RATE_HE. * * @NL80211_ATTR_FRAME_MATCH: A binary attribute which typically must contain * at least one byte, currently used with @NL80211_CMD_REGISTER_FRAME. @@ -2077,7 +2085,8 @@ enum nl80211_commands { * until the channel switch event. * @NL80211_ATTR_CH_SWITCH_BLOCK_TX: flag attribute specifying that transmission * must be blocked on the current channel (before the channel switch - * operation). + * operation). Also included in the channel switch started event if quiet + * was requested by the AP. * @NL80211_ATTR_CSA_IES: Nested set of attributes containing the IE information * for the time while performing a channel switch. * @NL80211_ATTR_CNTDWN_OFFS_BEACON: An array of offsets (u16) to the channel @@ -2527,6 +2536,20 @@ enum nl80211_commands { * override mask. Used with NL80211_ATTR_S1G_CAPABILITY in * NL80211_CMD_ASSOCIATE or NL80211_CMD_CONNECT. * + * @NL80211_ATTR_SAE_PWE: Indicates the mechanism(s) allowed for SAE PWE + * derivation in WPA3-Personal networks which are using SAE authentication. + * This is a u8 attribute that encapsulates one of the values from + * &enum nl80211_sae_pwe_mechanism. + * + * @NL80211_ATTR_SAR_SPEC: SAR power limitation specification when + * used with %NL80211_CMD_SET_SAR_SPECS. The message contains fields + * of %nl80211_sar_attrs which specifies the sar type and related + * sar specs. Sar specs contains array of %nl80211_sar_specs_attrs. + * + * @NL80211_ATTR_RECONNECT_REQUESTED: flag attribute, used with deauth and + * disassoc events to indicate that an immediate reconnect to the AP + * is desired. + * * @NUM_NL80211_ATTR: total number of nl80211_attrs available * @NL80211_ATTR_MAX: highest attribute number currently defined * @__NL80211_ATTR_AFTER_LAST: internal use @@ -3016,6 +3039,12 @@ enum nl80211_attrs { NL80211_ATTR_S1G_CAPABILITY, NL80211_ATTR_S1G_CAPABILITY_MASK, + NL80211_ATTR_SAE_PWE, + + NL80211_ATTR_RECONNECT_REQUESTED, + + NL80211_ATTR_SAR_SPEC, + /* add attributes here, update the policy in nl80211.c */ __NL80211_ATTR_AFTER_LAST, @@ -5896,6 +5925,9 @@ enum nl80211_feature_flags { * @NL80211_EXT_FEATURE_UNSOL_BCAST_PROBE_RESP: Driver/device supports * unsolicited broadcast probe response transmission * + * @NL80211_EXT_FEATURE_BEACON_RATE_HE: Driver supports beacon rate + * configuration (AP/mesh) with HE rates. + * * @NUM_NL80211_EXT_FEATURES: number of extended features. * @MAX_NL80211_EXT_FEATURES: highest extended feature index. */ @@ -5956,6 +5988,7 @@ enum nl80211_ext_feature_index { NL80211_EXT_FEATURE_SAE_OFFLOAD_AP, NL80211_EXT_FEATURE_FILS_DISCOVERY, NL80211_EXT_FEATURE_UNSOL_BCAST_PROBE_RESP, + NL80211_EXT_FEATURE_BEACON_RATE_HE, /* add new features before the definition below */ NUM_NL80211_EXT_FEATURES, @@ -7124,4 +7157,115 @@ enum nl80211_unsol_bcast_probe_resp_attributes { NL80211_UNSOL_BCAST_PROBE_RESP_ATTR_MAX = __NL80211_UNSOL_BCAST_PROBE_RESP_ATTR_LAST - 1 }; + +/** + * enum nl80211_sae_pwe_mechanism - The mechanism(s) allowed for SAE PWE + * derivation. Applicable only when WPA3-Personal SAE authentication is + * used. + * + * @NL80211_SAE_PWE_UNSPECIFIED: not specified, used internally to indicate that + * attribute is not present from userspace. + * @NL80211_SAE_PWE_HUNT_AND_PECK: hunting-and-pecking loop only + * @NL80211_SAE_PWE_HASH_TO_ELEMENT: hash-to-element only + * @NL80211_SAE_PWE_BOTH: both hunting-and-pecking loop and hash-to-element + * can be used. + */ +enum nl80211_sae_pwe_mechanism { + NL80211_SAE_PWE_UNSPECIFIED, + NL80211_SAE_PWE_HUNT_AND_PECK, + NL80211_SAE_PWE_HASH_TO_ELEMENT, + NL80211_SAE_PWE_BOTH, +}; + +/** + * enum nl80211_sar_type - type of SAR specs + * + * @NL80211_SAR_TYPE_POWER: power limitation specified in 0.25dBm unit + * + */ +enum nl80211_sar_type { + NL80211_SAR_TYPE_POWER, + + /* add new type here */ + + /* Keep last */ + NUM_NL80211_SAR_TYPE, +}; + +/** + * enum nl80211_sar_attrs - Attributes for SAR spec + * + * @NL80211_SAR_ATTR_TYPE: the SAR type as defined in &enum nl80211_sar_type. + * + * @NL80211_SAR_ATTR_SPECS: Nested array of SAR power + * limit specifications. Each specification contains a set + * of %nl80211_sar_specs_attrs. + * + * For SET operation, it contains array of %NL80211_SAR_ATTR_SPECS_POWER + * and %NL80211_SAR_ATTR_SPECS_RANGE_INDEX. + * + * For sar_capa dump, it contains array of + * %NL80211_SAR_ATTR_SPECS_START_FREQ + * and %NL80211_SAR_ATTR_SPECS_END_FREQ. + * + * @__NL80211_SAR_ATTR_LAST: Internal + * @NL80211_SAR_ATTR_MAX: highest sar attribute + * + * These attributes are used with %NL80211_CMD_SET_SAR_SPEC + */ +enum nl80211_sar_attrs { + __NL80211_SAR_ATTR_INVALID, + + NL80211_SAR_ATTR_TYPE, + NL80211_SAR_ATTR_SPECS, + + __NL80211_SAR_ATTR_LAST, + NL80211_SAR_ATTR_MAX = __NL80211_SAR_ATTR_LAST - 1, +}; + +/** + * enum nl80211_sar_specs_attrs - Attributes for SAR power limit specs + * + * @NL80211_SAR_ATTR_SPECS_POWER: Required (s32)value to specify the actual + * power limit value in units of 0.25 dBm if type is + * NL80211_SAR_TYPE_POWER. (i.e., a value of 44 represents 11 dBm). + * 0 means userspace doesn't have SAR limitation on this associated range. + * + * @NL80211_SAR_ATTR_SPECS_RANGE_INDEX: Required (u32) value to specify the + * index of exported freq range table and the associated power limitation + * is applied to this range. + * + * Userspace isn't required to set all the ranges advertised by WLAN driver, + * and userspace can skip some certain ranges. These skipped ranges don't + * have SAR limitations, and they are same as setting the + * %NL80211_SAR_ATTR_SPECS_POWER to any unreasonable high value because any + * value higher than regulatory allowed value just means SAR power + * limitation is removed, but it's required to set at least one range. + * It's not allowed to set duplicated range in one SET operation. + * + * Every SET operation overwrites previous SET operation. + * + * @NL80211_SAR_ATTR_SPECS_START_FREQ: Required (u32) value to specify the start + * frequency of this range edge when registering SAR capability to wiphy. + * It's not a channel center frequency. The unit is kHz. + * + * @NL80211_SAR_ATTR_SPECS_END_FREQ: Required (u32) value to specify the end + * frequency of this range edge when registering SAR capability to wiphy. + * It's not a channel center frequency. The unit is kHz. + * + * @__NL80211_SAR_ATTR_SPECS_LAST: Internal + * @NL80211_SAR_ATTR_SPECS_MAX: highest sar specs attribute + */ +enum nl80211_sar_specs_attrs { + __NL80211_SAR_ATTR_SPECS_INVALID, + + NL80211_SAR_ATTR_SPECS_POWER, + NL80211_SAR_ATTR_SPECS_RANGE_INDEX, + NL80211_SAR_ATTR_SPECS_START_FREQ, + NL80211_SAR_ATTR_SPECS_END_FREQ, + + __NL80211_SAR_ATTR_SPECS_LAST, + NL80211_SAR_ATTR_SPECS_MAX = __NL80211_SAR_ATTR_SPECS_LAST - 1, +}; + #endif /* __LINUX_NL80211_H */ |