diff options
Diffstat (limited to 'include/net/mac80211.h')
| -rw-r--r-- | include/net/mac80211.h | 156 |
1 files changed, 126 insertions, 30 deletions
diff --git a/include/net/mac80211.h b/include/net/mac80211.h index 66e2bfd165e8..dcdba96814a2 100644 --- a/include/net/mac80211.h +++ b/include/net/mac80211.h @@ -317,6 +317,9 @@ struct ieee80211_vif_chanctx_switch { * @BSS_CHANGED_TWT: TWT status changed * @BSS_CHANGED_HE_OBSS_PD: OBSS Packet Detection status changed. * @BSS_CHANGED_HE_BSS_COLOR: BSS Color has changed + * @BSS_CHANGED_FILS_DISCOVERY: FILS discovery status changed. + * @BSS_CHANGED_UNSOL_BCAST_PROBE_RESP: Unsolicited broadcast probe response + * status changed. * */ enum ieee80211_bss_change { @@ -350,6 +353,8 @@ enum ieee80211_bss_change { BSS_CHANGED_TWT = 1<<27, BSS_CHANGED_HE_OBSS_PD = 1<<28, BSS_CHANGED_HE_BSS_COLOR = 1<<29, + BSS_CHANGED_FILS_DISCOVERY = 1<<30, + BSS_CHANGED_UNSOL_BCAST_PROBE_RESP = 1<<31, /* when adding here, make sure to change ieee80211_reconfig */ }; @@ -491,6 +496,18 @@ struct ieee80211_ftm_responder_params { }; /** + * struct ieee80211_fils_discovery - FILS discovery parameters from + * IEEE Std 802.11ai-2016, Annex C.3 MIB detail. + * + * @min_interval: Minimum packet interval in TUs (0 - 10000) + * @max_interval: Maximum packet interval in TUs (0 - 10000) + */ +struct ieee80211_fils_discovery { + u32 min_interval; + u32 max_interval; +}; + +/** * struct ieee80211_bss_conf - holds the BSS's changing parameters * * This structure keeps information about a BSS (and an association @@ -607,6 +624,12 @@ struct ieee80211_ftm_responder_params { * @he_oper: HE operation information of the AP we are connected to * @he_obss_pd: OBSS Packet Detection parameters. * @he_bss_color: BSS coloring settings, if BSS supports HE + * @fils_discovery: FILS discovery configuration + * @unsol_bcast_probe_resp_interval: Unsolicited broadcast probe response + * interval. + * @s1g: BSS is S1G BSS (affects Association Request format). + * @beacon_tx_rate: The configured beacon transmit rate that needs to be passed + * to driver when rate control is offloaded to firmware. */ struct ieee80211_bss_conf { const u8 *bssid; @@ -674,6 +697,10 @@ struct ieee80211_bss_conf { } he_oper; struct ieee80211_he_obss_pd he_obss_pd; struct cfg80211_he_bss_color he_bss_color; + struct ieee80211_fils_discovery fils_discovery; + u32 unsol_bcast_probe_resp_interval; + bool s1g; + struct cfg80211_bitrate_mask beacon_tx_rate; }; /** @@ -720,9 +747,8 @@ struct ieee80211_bss_conf { * @IEEE80211_TX_INTFL_OFFCHAN_TX_OK: Internal to mac80211. Used to indicate * that a frame can be transmitted while the queues are stopped for * off-channel operation. - * @IEEE80211_TX_INTFL_NEED_TXPROCESSING: completely internal to mac80211, - * used to indicate that a pending frame requires TX processing before - * it can be sent out. + * @IEEE80211_TX_CTL_HW_80211_ENCAP: This frame uses hardware encapsulation + * (header conversion) * @IEEE80211_TX_INTFL_RETRIED: completely internal to mac80211, * used to indicate that a frame was already retried due to PS * @IEEE80211_TX_INTFL_DONT_ENCRYPT: completely internal to mac80211, @@ -791,7 +817,7 @@ enum mac80211_tx_info_flags { IEEE80211_TX_STAT_AMPDU_NO_BACK = BIT(11), IEEE80211_TX_CTL_RATE_CTRL_PROBE = BIT(12), IEEE80211_TX_INTFL_OFFCHAN_TX_OK = BIT(13), - IEEE80211_TX_INTFL_NEED_TXPROCESSING = BIT(14), + IEEE80211_TX_CTL_HW_80211_ENCAP = BIT(14), IEEE80211_TX_INTFL_RETRIED = BIT(15), IEEE80211_TX_INTFL_DONT_ENCRYPT = BIT(16), IEEE80211_TX_CTL_NO_PS_BUFFER = BIT(17), @@ -812,6 +838,8 @@ enum mac80211_tx_info_flags { #define IEEE80211_TX_CTL_STBC_SHIFT 23 +#define IEEE80211_TX_RC_S1G_MCS IEEE80211_TX_RC_VHT_MCS + /** * enum mac80211_tx_control_flags - flags to describe transmit control * @@ -823,8 +851,9 @@ enum mac80211_tx_info_flags { * @IEEE80211_TX_CTRL_AMSDU: This frame is an A-MSDU frame * @IEEE80211_TX_CTRL_FAST_XMIT: This frame is going through the fast_xmit path * @IEEE80211_TX_CTRL_SKIP_MPATH_LOOKUP: This frame skips mesh path lookup - * @IEEE80211_TX_CTRL_HW_80211_ENCAP: This frame uses hardware encapsulation - * (header conversion) + * @IEEE80211_TX_INTCFL_NEED_TXPROCESSING: completely internal to mac80211, + * used to indicate that a pending frame requires TX processing before + * it can be sent out. * @IEEE80211_TX_CTRL_NO_SEQNO: Do not overwrite the sequence number that * has already been assigned to this frame. * @@ -837,7 +866,7 @@ enum mac80211_tx_control_flags { IEEE80211_TX_CTRL_AMSDU = BIT(3), IEEE80211_TX_CTRL_FAST_XMIT = BIT(4), IEEE80211_TX_CTRL_SKIP_MPATH_LOOKUP = BIT(5), - IEEE80211_TX_CTRL_HW_80211_ENCAP = BIT(6), + IEEE80211_TX_INTCFL_NEED_TXPROCESSING = BIT(6), IEEE80211_TX_CTRL_NO_SEQNO = BIT(7), }; @@ -1002,7 +1031,8 @@ ieee80211_rate_get_vht_nss(const struct ieee80211_tx_rate *rate) * @status.ampdu_ack_len: AMPDU ack length * @status.ampdu_len: AMPDU length * @status.antenna: (legacy, kept only for iwlegacy) - * @status.tx_time: airtime consumed for transmission + * @status.tx_time: airtime consumed for transmission; note this is only + * used for WMM AC, not for airtime fairness * @status.is_valid_ack_signal: ACK signal is valid * @status.status_driver_data: driver use area * @ack: union part for pure ACK data @@ -1095,12 +1125,14 @@ ieee80211_info_get_tx_time_est(struct ieee80211_tx_info *info) * @info: Basic tx status information * @skb: Packet skb (can be NULL if not provided by the driver) * @rate: The TX rate that was used when sending the packet + * @free_list: list where processed skbs are stored to be free'd by the driver */ struct ieee80211_tx_status { struct ieee80211_sta *sta; struct ieee80211_tx_info *info; struct sk_buff *skb; struct rate_info *rate; + struct list_head *free_list; }; /** @@ -1606,6 +1638,21 @@ enum ieee80211_vif_flags { IEEE80211_VIF_GET_NOA_UPDATE = BIT(3), }; + +/** + * enum ieee80211_offload_flags - virtual interface offload flags + * + * @IEEE80211_OFFLOAD_ENCAP_ENABLED: tx encapsulation offload is enabled + * The driver supports sending frames passed as 802.3 frames by mac80211. + * It must also support sending 802.11 packets for the same interface. + * @IEEE80211_OFFLOAD_ENCAP_4ADDR: support 4-address mode encapsulation offload + */ + +enum ieee80211_offload_flags { + IEEE80211_OFFLOAD_ENCAP_ENABLED = BIT(0), + IEEE80211_OFFLOAD_ENCAP_4ADDR = BIT(1), +}; + /** * struct ieee80211_vif - per-interface data * @@ -1626,6 +1673,11 @@ enum ieee80211_vif_flags { * these need to be set (or cleared) when the interface is added * or, if supported by the driver, the interface type is changed * at runtime, mac80211 will never touch this field + * @offloaad_flags: hardware offload capabilities/flags for this interface. + * These are initialized by mac80211 before calling .add_interface, + * .change_interface or .update_vif_offload and updated by the driver + * within these ops, based on supported features or runtime change + * restrictions. * @hw_queue: hardware queue for each AC * @cab_queue: content-after-beacon (DTIM beacon really) queue, AP mode only * @chanctx_conf: The channel context this interface is assigned to, or %NULL @@ -1645,6 +1697,8 @@ enum ieee80211_vif_flags { * @txq: the multicast data TX queue (if driver uses the TXQ abstraction) * @txqs_stopped: per AC flag to indicate that intermediate TXQs are stopped, * protected by fq->lock. + * @offload_flags: 802.3 -> 802.11 enapsulation offload flags, see + * &enum ieee80211_offload_flags. */ struct ieee80211_vif { enum nl80211_iftype type; @@ -1662,6 +1716,7 @@ struct ieee80211_vif { struct ieee80211_chanctx_conf __rcu *chanctx_conf; u32 driver_flags; + u32 offload_flags; #ifdef CONFIG_MAC80211_DEBUGFS struct dentry *debugfs_dir; @@ -2328,6 +2383,9 @@ struct ieee80211_txq { * aggregating MPDUs with the same keyid, allowing mac80211 to keep Tx * A-MPDU sessions active while rekeying with Extended Key ID. * + * @IEEE80211_HW_SUPPORTS_TX_ENCAP_OFFLOAD: Hardware supports tx encapsulation + * offload + * * @NUM_IEEE80211_HW_FLAGS: number of hardware flags, used for sizing arrays */ enum ieee80211_hw_flags { @@ -2380,6 +2438,7 @@ enum ieee80211_hw_flags { IEEE80211_HW_SUPPORTS_MULTI_BSSID, IEEE80211_HW_SUPPORTS_ONLY_HE_MULTI_BSSID, IEEE80211_HW_AMPDU_KEYBORDER_SUPPORT, + IEEE80211_HW_SUPPORTS_TX_ENCAP_OFFLOAD, /* keep last, obviously */ NUM_IEEE80211_HW_FLAGS @@ -3252,7 +3311,7 @@ enum ieee80211_roc_type { }; /** - * enum ieee80211_reconfig_complete_type - reconfig type + * enum ieee80211_reconfig_type - reconfig type * * This enum is used by the reconfig_complete() callback to indicate what * reconfiguration type was completed. @@ -3736,7 +3795,7 @@ enum ieee80211_reconfig_type { * decremented, and when they reach 1 the driver must call * ieee80211_csa_finish(). Drivers which use ieee80211_beacon_get() * get the csa counter decremented by mac80211, but must check if it is - * 1 using ieee80211_csa_is_complete() after the beacon has been + * 1 using ieee80211_beacon_counter_is_complete() after the beacon has been * transmitted and then call ieee80211_csa_finish(). * If the CSA count starts as zero or 1, this function will not be called, * since there won't be any time to beacon before the switch anyway. @@ -3814,6 +3873,10 @@ enum ieee80211_reconfig_type { * @set_tid_config: Apply TID specific configurations. This callback may sleep. * @reset_tid_config: Reset TID specific configuration for the peer. * This callback may sleep. + * @update_vif_offload: Update virtual interface offload flags + * This callback may sleep. + * @sta_set_4addr: Called to notify the driver when a station starts/stops using + * 4-address mode */ struct ieee80211_ops { void (*tx)(struct ieee80211_hw *hw, @@ -4125,6 +4188,10 @@ struct ieee80211_ops { int (*reset_tid_config)(struct ieee80211_hw *hw, struct ieee80211_vif *vif, struct ieee80211_sta *sta, u8 tids); + void (*update_vif_offload)(struct ieee80211_hw *hw, + struct ieee80211_vif *vif); + void (*sta_set_4addr)(struct ieee80211_hw *hw, struct ieee80211_vif *vif, + struct ieee80211_sta *sta, bool enabled); }; /** @@ -4763,21 +4830,21 @@ void ieee80211_tx_status_8023(struct ieee80211_hw *hw, */ void ieee80211_report_low_ack(struct ieee80211_sta *sta, u32 num_packets); -#define IEEE80211_MAX_CSA_COUNTERS_NUM 2 +#define IEEE80211_MAX_CNTDWN_COUNTERS_NUM 2 /** * struct ieee80211_mutable_offsets - mutable beacon offsets * @tim_offset: position of TIM element * @tim_length: size of TIM element - * @csa_counter_offs: array of IEEE80211_MAX_CSA_COUNTERS_NUM offsets - * to CSA counters. This array can contain zero values which + * @cntdwn_counter_offs: array of IEEE80211_MAX_CNTDWN_COUNTERS_NUM offsets + * to countdown counters. This array can contain zero values which * should be ignored. */ struct ieee80211_mutable_offsets { u16 tim_offset; u16 tim_length; - u16 csa_counter_offs[IEEE80211_MAX_CSA_COUNTERS_NUM]; + u16 cntdwn_counter_offs[IEEE80211_MAX_CNTDWN_COUNTERS_NUM]; }; /** @@ -4846,31 +4913,31 @@ static inline struct sk_buff *ieee80211_beacon_get(struct ieee80211_hw *hw, } /** - * ieee80211_csa_update_counter - request mac80211 to decrement the csa counter + * ieee80211_beacon_update_cntdwn - request mac80211 to decrement the beacon countdown * @vif: &struct ieee80211_vif pointer from the add_interface callback. * - * The csa counter should be updated after each beacon transmission. + * The beacon counter should be updated after each beacon transmission. * This function is called implicitly when * ieee80211_beacon_get/ieee80211_beacon_get_tim are called, however if the * beacon frames are generated by the device, the driver should call this - * function after each beacon transmission to sync mac80211's csa counters. + * function after each beacon transmission to sync mac80211's beacon countdown. * - * Return: new csa counter value + * Return: new countdown value */ -u8 ieee80211_csa_update_counter(struct ieee80211_vif *vif); +u8 ieee80211_beacon_update_cntdwn(struct ieee80211_vif *vif); /** - * ieee80211_csa_set_counter - request mac80211 to set csa counter + * ieee80211_beacon_set_cntdwn - request mac80211 to set beacon countdown * @vif: &struct ieee80211_vif pointer from the add_interface callback. * @counter: the new value for the counter * - * The csa counter can be changed by the device, this API should be + * The beacon countdown can be changed by the device, this API should be * used by the device driver to update csa counter in mac80211. * - * It should never be used together with ieee80211_csa_update_counter(), + * It should never be used together with ieee80211_beacon_update_cntdwn(), * as it will cause a race condition around the counter value. */ -void ieee80211_csa_set_counter(struct ieee80211_vif *vif, u8 counter); +void ieee80211_beacon_set_cntdwn(struct ieee80211_vif *vif, u8 counter); /** * ieee80211_csa_finish - notify mac80211 about channel switch @@ -4883,13 +4950,12 @@ void ieee80211_csa_set_counter(struct ieee80211_vif *vif, u8 counter); void ieee80211_csa_finish(struct ieee80211_vif *vif); /** - * ieee80211_csa_is_complete - find out if counters reached 1 + * ieee80211_beacon_cntdwn_is_complete - find out if countdown reached 1 * @vif: &struct ieee80211_vif pointer from the add_interface callback. * - * This function returns whether the channel switch counters reached zero. + * This function returns whether the countdown reached zero. */ -bool ieee80211_csa_is_complete(struct ieee80211_vif *vif); - +bool ieee80211_beacon_cntdwn_is_complete(struct ieee80211_vif *vif); /** * ieee80211_proberesp_get - retrieve a Probe Response template @@ -5344,11 +5410,15 @@ void ieee80211_sched_scan_stopped(struct ieee80211_hw *hw); * @IEEE80211_IFACE_ITER_RESUME_ALL: During resume, iterate over all * interfaces, even if they haven't been re-added to the driver yet. * @IEEE80211_IFACE_ITER_ACTIVE: Iterate only active interfaces (netdev is up). + * @IEEE80211_IFACE_SKIP_SDATA_NOT_IN_DRIVER: Skip any interfaces where SDATA + * is not in the driver. This may fix crashes during firmware recovery + * for instance. */ enum ieee80211_interface_iteration_flags { IEEE80211_IFACE_ITER_NORMAL = 0, IEEE80211_IFACE_ITER_RESUME_ALL = BIT(0), IEEE80211_IFACE_ITER_ACTIVE = BIT(1), + IEEE80211_IFACE_SKIP_SDATA_NOT_IN_DRIVER = BIT(2), }; /** @@ -5648,7 +5718,7 @@ void ieee80211_send_eosp_nullfunc(struct ieee80211_sta *pubsta, int tid); /** * ieee80211_sta_register_airtime - register airtime usage for a sta/tid * - * Register airtime usage for a given sta on a given tid. The driver can call + * Register airtime usage for a given sta on a given tid. The driver must call * this function to notify mac80211 that a station used a certain amount of * airtime. This information will be used by the TXQ scheduler to schedule * stations in a way that ensures airtime fairness. @@ -6264,7 +6334,8 @@ bool ieee80211_tx_prepare_skb(struct ieee80211_hw *hw, int band, struct ieee80211_sta **sta); /** - * Sanity-check and parse the radiotap header of injected frames + * ieee80211_parse_tx_radiotap - Sanity-check and parse the radiotap header + * of injected frames * @skb: packet injected by userspace * @dev: the &struct device of this 802.11 device */ @@ -6319,7 +6390,7 @@ int ieee80211_parse_p2p_noa(const struct ieee80211_p2p_noa_attr *attr, void ieee80211_update_p2p_noa(struct ieee80211_noa_data *data, u32 tsf); /** - * ieee80211_tdls_oper - request userspace to perform a TDLS operation + * ieee80211_tdls_oper_request - request userspace to perform a TDLS operation * @vif: virtual interface * @peer: the peer's destination address * @oper: the requested TDLS operation @@ -6594,4 +6665,29 @@ u32 ieee80211_calc_tx_airtime(struct ieee80211_hw *hw, */ bool ieee80211_set_hw_80211_encap(struct ieee80211_vif *vif, bool enable); +/** + * ieee80211_get_fils_discovery_tmpl - Get FILS discovery template. + * @hw: pointer obtained from ieee80211_alloc_hw(). + * @vif: &struct ieee80211_vif pointer from the add_interface callback. + * + * The driver is responsible for freeing the returned skb. + * + * Return: FILS discovery template. %NULL on error. + */ +struct sk_buff *ieee80211_get_fils_discovery_tmpl(struct ieee80211_hw *hw, + struct ieee80211_vif *vif); + +/** + * ieee80211_get_unsol_bcast_probe_resp_tmpl - Get unsolicited broadcast + * probe response template. + * @hw: pointer obtained from ieee80211_alloc_hw(). + * @vif: &struct ieee80211_vif pointer from the add_interface callback. + * + * The driver is responsible for freeing the returned skb. + * + * Return: Unsolicited broadcast probe response template. %NULL on error. + */ +struct sk_buff * +ieee80211_get_unsol_bcast_probe_resp_tmpl(struct ieee80211_hw *hw, + struct ieee80211_vif *vif); #endif /* MAC80211_H */ |