diff options
Diffstat (limited to 'drivers')
| -rw-r--r-- | drivers/ata/libata-core.c | 78 | ||||
| -rw-r--r-- | drivers/ata/libata-eh.c | 95 |
2 files changed, 0 insertions, 173 deletions
diff --git a/drivers/ata/libata-core.c b/drivers/ata/libata-core.c index 81898036dbca..1584164e7704 100644 --- a/drivers/ata/libata-core.c +++ b/drivers/ata/libata-core.c @@ -2581,81 +2581,6 @@ void sata_print_link_status(struct ata_link *link) } /** - * __sata_phy_reset - Wake/reset a low-level SATA PHY - * @ap: SATA port associated with target SATA PHY. - * - * This function issues commands to standard SATA Sxxx - * PHY registers, to wake up the phy (and device), and - * clear any reset condition. - * - * LOCKING: - * PCI/etc. bus probe sem. - * - */ -void __sata_phy_reset(struct ata_port *ap) -{ - struct ata_link *link = &ap->link; - unsigned long timeout = jiffies + (HZ * 5); - u32 sstatus; - - if (ap->flags & ATA_FLAG_SATA_RESET) { - /* issue phy wake/reset */ - sata_scr_write_flush(link, SCR_CONTROL, 0x301); - /* Couldn't find anything in SATA I/II specs, but - * AHCI-1.1 10.4.2 says at least 1 ms. */ - mdelay(1); - } - /* phy wake/clear reset */ - sata_scr_write_flush(link, SCR_CONTROL, 0x300); - - /* wait for phy to become ready, if necessary */ - do { - msleep(200); - sata_scr_read(link, SCR_STATUS, &sstatus); - if ((sstatus & 0xf) != 1) - break; - } while (time_before(jiffies, timeout)); - - /* print link status */ - sata_print_link_status(link); - - /* TODO: phy layer with polling, timeouts, etc. */ - if (!ata_link_offline(link)) - ata_port_probe(ap); - else - ata_port_disable(ap); - - if (ap->flags & ATA_FLAG_DISABLED) - return; - - if (ata_busy_sleep(ap, ATA_TMOUT_BOOT_QUICK, ATA_TMOUT_BOOT)) { - ata_port_disable(ap); - return; - } - - ap->cbl = ATA_CBL_SATA; -} - -/** - * sata_phy_reset - Reset SATA bus. - * @ap: SATA port associated with target SATA PHY. - * - * This function resets the SATA bus, and then probes - * the bus for devices. - * - * LOCKING: - * PCI/etc. bus probe sem. - * - */ -void sata_phy_reset(struct ata_port *ap) -{ - __sata_phy_reset(ap); - if (ap->flags & ATA_FLAG_DISABLED) - return; - ata_bus_reset(ap); -} - -/** * ata_dev_pair - return other device on cable * @adev: device * @@ -7653,8 +7578,6 @@ EXPORT_SYMBOL_GPL(ata_dev_disable); EXPORT_SYMBOL_GPL(sata_set_spd); EXPORT_SYMBOL_GPL(sata_link_debounce); EXPORT_SYMBOL_GPL(sata_link_resume); -EXPORT_SYMBOL_GPL(sata_phy_reset); -EXPORT_SYMBOL_GPL(__sata_phy_reset); EXPORT_SYMBOL_GPL(ata_bus_reset); EXPORT_SYMBOL_GPL(ata_std_prereset); EXPORT_SYMBOL_GPL(ata_std_softreset); @@ -7725,7 +7648,6 @@ EXPORT_SYMBOL_GPL(ata_port_desc); #ifdef CONFIG_PCI EXPORT_SYMBOL_GPL(ata_port_pbar_desc); #endif /* CONFIG_PCI */ -EXPORT_SYMBOL_GPL(ata_eng_timeout); EXPORT_SYMBOL_GPL(ata_port_schedule_eh); EXPORT_SYMBOL_GPL(ata_link_abort); EXPORT_SYMBOL_GPL(ata_port_abort); diff --git a/drivers/ata/libata-eh.c b/drivers/ata/libata-eh.c index ed8813b222a0..0dac69db1fdf 100644 --- a/drivers/ata/libata-eh.c +++ b/drivers/ata/libata-eh.c @@ -559,101 +559,6 @@ void ata_port_wait_eh(struct ata_port *ap) } } -/** - * ata_qc_timeout - Handle timeout of queued command - * @qc: Command that timed out - * - * Some part of the kernel (currently, only the SCSI layer) - * has noticed that the active command on port @ap has not - * completed after a specified length of time. Handle this - * condition by disabling DMA (if necessary) and completing - * transactions, with error if necessary. - * - * This also handles the case of the "lost interrupt", where - * for some reason (possibly hardware bug, possibly driver bug) - * an interrupt was not delivered to the driver, even though the - * transaction completed successfully. - * - * TODO: kill this function once old EH is gone. - * - * LOCKING: - * Inherited from SCSI layer (none, can sleep) - */ -static void ata_qc_timeout(struct ata_queued_cmd *qc) -{ - struct ata_port *ap = qc->ap; - u8 host_stat = 0, drv_stat; - unsigned long flags; - - DPRINTK("ENTER\n"); - - ap->hsm_task_state = HSM_ST_IDLE; - - spin_lock_irqsave(ap->lock, flags); - - switch (qc->tf.protocol) { - - case ATA_PROT_DMA: - case ATA_PROT_ATAPI_DMA: - host_stat = ap->ops->bmdma_status(ap); - - /* before we do anything else, clear DMA-Start bit */ - ap->ops->bmdma_stop(qc); - - /* fall through */ - - default: - ata_altstatus(ap); - drv_stat = ata_chk_status(ap); - - /* ack bmdma irq events */ - ap->ops->irq_clear(ap); - - ata_dev_printk(qc->dev, KERN_ERR, "command 0x%x timeout, " - "stat 0x%x host_stat 0x%x\n", - qc->tf.command, drv_stat, host_stat); - - /* complete taskfile transaction */ - qc->err_mask |= AC_ERR_TIMEOUT; - break; - } - - spin_unlock_irqrestore(ap->lock, flags); - - ata_eh_qc_complete(qc); - - DPRINTK("EXIT\n"); -} - -/** - * ata_eng_timeout - Handle timeout of queued command - * @ap: Port on which timed-out command is active - * - * Some part of the kernel (currently, only the SCSI layer) - * has noticed that the active command on port @ap has not - * completed after a specified length of time. Handle this - * condition by disabling DMA (if necessary) and completing - * transactions, with error if necessary. - * - * This also handles the case of the "lost interrupt", where - * for some reason (possibly hardware bug, possibly driver bug) - * an interrupt was not delivered to the driver, even though the - * transaction completed successfully. - * - * TODO: kill this function once old EH is gone. - * - * LOCKING: - * Inherited from SCSI layer (none, can sleep) - */ -void ata_eng_timeout(struct ata_port *ap) -{ - DPRINTK("ENTER\n"); - - ata_qc_timeout(ata_qc_from_tag(ap, ap->link.active_tag)); - - DPRINTK("EXIT\n"); -} - static int ata_eh_nr_in_flight(struct ata_port *ap) { unsigned int tag; |