diff options
Diffstat (limited to 'drivers/usb')
61 files changed, 577 insertions, 397 deletions
diff --git a/drivers/usb/Kconfig b/drivers/usb/Kconfig index e4405e088589..76316a33061b 100644 --- a/drivers/usb/Kconfig +++ b/drivers/usb/Kconfig @@ -2,21 +2,13 @@ # USB device configuration # -menuconfig USB_SUPPORT - bool "USB support" - depends on HAS_IOMEM - default y - ---help--- - This option adds core support for Universal Serial Bus (USB). - You will also need drivers from the following menu to make use of it. - # many non-PCI SOC chips embed OHCI config USB_ARCH_HAS_OHCI boolean # ARM: default y if SA1111 default y if ARCH_OMAP - default y if ARCH_S3C2410 + default y if ARCH_S3C24XX default y if PXA27x default y if PXA3xx default y if ARCH_EP93XX @@ -44,7 +36,7 @@ config USB_ARCH_HAS_EHCI default y if PPC_MPC512x default y if ARCH_IXP4XX default y if ARCH_W90X900 - default y if ARCH_AT91SAM9G45 + default y if ARCH_AT91 default y if ARCH_MXC default y if ARCH_OMAP3 default y if ARCH_CNS3XXX @@ -63,6 +55,14 @@ config USB_ARCH_HAS_XHCI boolean default PCI +menuconfig USB_SUPPORT + bool "USB support" + depends on HAS_IOMEM + default y + ---help--- + This option adds core support for Universal Serial Bus (USB). + You will also need drivers from the following menu to make use of it. + if USB_SUPPORT config USB_COMMON diff --git a/drivers/usb/core/driver.c b/drivers/usb/core/driver.c index f8e2d6d52e5c..9a56635dc19c 100644 --- a/drivers/usb/core/driver.c +++ b/drivers/usb/core/driver.c @@ -1189,8 +1189,13 @@ static int usb_suspend_both(struct usb_device *udev, pm_message_t msg) if (status == 0) { status = usb_suspend_device(udev, msg); - /* Again, ignore errors during system sleep transitions */ - if (!PMSG_IS_AUTO(msg)) + /* + * Ignore errors from non-root-hub devices during + * system sleep transitions. For the most part, + * these devices should go to low power anyway when + * the entire bus is suspended. + */ + if (udev->parent && !PMSG_IS_AUTO(msg)) status = 0; } diff --git a/drivers/usb/core/hcd.c b/drivers/usb/core/hcd.c index 9d7fc9a39933..140d3e11f212 100644 --- a/drivers/usb/core/hcd.c +++ b/drivers/usb/core/hcd.c @@ -1978,6 +1978,18 @@ int hcd_bus_suspend(struct usb_device *rhdev, pm_message_t msg) if (status == 0) { usb_set_device_state(rhdev, USB_STATE_SUSPENDED); hcd->state = HC_STATE_SUSPENDED; + + /* Did we race with a root-hub wakeup event? */ + if (rhdev->do_remote_wakeup) { + char buffer[6]; + + status = hcd->driver->hub_status_data(hcd, buffer); + if (status != 0) { + dev_dbg(&rhdev->dev, "suspend raced with wakeup event\n"); + hcd_bus_resume(rhdev, PMSG_AUTO_RESUME); + status = -EBUSY; + } + } } else { spin_lock_irq(&hcd_root_hub_lock); if (!HCD_DEAD(hcd)) { diff --git a/drivers/usb/core/hub.c b/drivers/usb/core/hub.c index 28664eb7f555..a2aa9d652c67 100644 --- a/drivers/usb/core/hub.c +++ b/drivers/usb/core/hub.c @@ -3163,6 +3163,22 @@ hub_port_init (struct usb_hub *hub, struct usb_device *udev, int port1, if (retval) goto fail; + /* + * Some superspeed devices have finished the link training process + * and attached to a superspeed hub port, but the device descriptor + * got from those devices show they aren't superspeed devices. Warm + * reset the port attached by the devices can fix them. + */ + if ((udev->speed == USB_SPEED_SUPER) && + (le16_to_cpu(udev->descriptor.bcdUSB) < 0x0300)) { + dev_err(&udev->dev, "got a wrong device descriptor, " + "warm reset device\n"); + hub_port_reset(hub, port1, udev, + HUB_BH_RESET_TIME, true); + retval = -EINVAL; + goto fail; + } + if (udev->descriptor.bMaxPacketSize0 == 0xff || udev->speed == USB_SPEED_SUPER) i = 512; diff --git a/drivers/usb/core/inode.c b/drivers/usb/core/inode.c index 9e186f3da839..d2b9af59cba9 100644 --- a/drivers/usb/core/inode.c +++ b/drivers/usb/core/inode.c @@ -50,7 +50,6 @@ static const struct file_operations default_file_operations; static struct vfsmount *usbfs_mount; static int usbfs_mount_count; /* = 0 */ -static int ignore_mount = 0; static struct dentry *devices_usbfs_dentry; static int num_buses; /* = 0 */ @@ -256,7 +255,7 @@ static int remount(struct super_block *sb, int *flags, char *data) * i.e. it's a simple_pin_fs from create_special_files, * then ignore it. */ - if (ignore_mount) + if (*flags & MS_KERNMOUNT) return 0; if (parse_options(sb, data)) { @@ -429,18 +428,10 @@ static loff_t default_file_lseek (struct file *file, loff_t offset, int orig) return retval; } -static int default_open (struct inode *inode, struct file *file) -{ - if (inode->i_private) - file->private_data = inode->i_private; - - return 0; -} - static const struct file_operations default_file_operations = { .read = default_read_file, .write = default_write_file, - .open = default_open, + .open = simple_open, .llseek = default_file_lseek, }; @@ -454,7 +445,6 @@ static const struct super_operations usbfs_ops = { static int usbfs_fill_super(struct super_block *sb, void *data, int silent) { struct inode *inode; - struct dentry *root; sb->s_blocksize = PAGE_CACHE_SIZE; sb->s_blocksize_bits = PAGE_CACHE_SHIFT; @@ -462,19 +452,11 @@ static int usbfs_fill_super(struct super_block *sb, void *data, int silent) sb->s_op = &usbfs_ops; sb->s_time_gran = 1; inode = usbfs_get_inode(sb, S_IFDIR | 0755, 0); - - if (!inode) { - dbg("%s: could not get inode!",__func__); - return -ENOMEM; - } - - root = d_alloc_root(inode); - if (!root) { + sb->s_root = d_make_root(inode); + if (!sb->s_root) { dbg("%s: could not get root dentry!",__func__); - iput(inode); return -ENOMEM; } - sb->s_root = root; return 0; } @@ -591,11 +573,6 @@ static int create_special_files (void) struct dentry *parent; int retval; - /* the simple_pin_fs calls will call remount with no options - * without this flag that would overwrite the real mount options (if any) - */ - ignore_mount = 1; - /* create the devices special file */ retval = simple_pin_fs(&usb_fs_type, &usbfs_mount, &usbfs_mount_count); if (retval) { @@ -603,8 +580,6 @@ static int create_special_files (void) goto exit; } - ignore_mount = 0; - parent = usbfs_mount->mnt_root; devices_usbfs_dentry = fs_create_file ("devices", listmode | S_IFREG, parent, diff --git a/drivers/usb/core/message.c b/drivers/usb/core/message.c index b3bdfede45e6..aed3e07942d4 100644 --- a/drivers/usb/core/message.c +++ b/drivers/usb/core/message.c @@ -308,7 +308,8 @@ static void sg_complete(struct urb *urb) retval = usb_unlink_urb(io->urbs [i]); if (retval != -EINPROGRESS && retval != -ENODEV && - retval != -EBUSY) + retval != -EBUSY && + retval != -EIDRM) dev_err(&io->dev->dev, "%s, unlink --> %d\n", __func__, retval); @@ -317,7 +318,6 @@ static void sg_complete(struct urb *urb) } spin_lock(&io->lock); } - urb->dev = NULL; /* on the last completion, signal usb_sg_wait() */ io->bytes += urb->actual_length; @@ -524,7 +524,6 @@ void usb_sg_wait(struct usb_sg_request *io) case -ENXIO: /* hc didn't queue this one */ case -EAGAIN: case -ENOMEM: - io->urbs[i]->dev = NULL; retval = 0; yield(); break; @@ -542,7 +541,6 @@ void usb_sg_wait(struct usb_sg_request *io) /* fail any uncompleted urbs */ default: - io->urbs[i]->dev = NULL; io->urbs[i]->status = retval; dev_dbg(&io->dev->dev, "%s, submit --> %d\n", __func__, retval); @@ -593,7 +591,10 @@ void usb_sg_cancel(struct usb_sg_request *io) if (!io->urbs [i]->dev) continue; retval = usb_unlink_urb(io->urbs [i]); - if (retval != -EINPROGRESS && retval != -EBUSY) + if (retval != -EINPROGRESS + && retval != -ENODEV + && retval != -EBUSY + && retval != -EIDRM) dev_warn(&io->dev->dev, "%s, unlink --> %d\n", __func__, retval); } diff --git a/drivers/usb/core/urb.c b/drivers/usb/core/urb.c index 7239a73c1b8c..cd9b3a2cd8a7 100644 --- a/drivers/usb/core/urb.c +++ b/drivers/usb/core/urb.c @@ -539,6 +539,10 @@ EXPORT_SYMBOL_GPL(usb_submit_urb); * never submitted, or it was unlinked before, or the hardware is already * finished with it), even if the completion handler has not yet run. * + * The URB must not be deallocated while this routine is running. In + * particular, when a driver calls this routine, it must insure that the + * completion handler cannot deallocate the URB. + * * Unlinking and Endpoint Queues: * * [The behaviors and guarantees described below do not apply to virtual @@ -603,6 +607,10 @@ EXPORT_SYMBOL_GPL(usb_unlink_urb); * with error -EPERM. Thus even if the URB's completion handler always * tries to resubmit, it will not succeed and the URB will become idle. * + * The URB must not be deallocated while this routine is running. In + * particular, when a driver calls this routine, it must insure that the + * completion handler cannot deallocate the URB. + * * This routine may not be used in an interrupt context (such as a bottom * half or a completion handler), or when holding a spinlock, or in other * situations where the caller can't schedule(). @@ -640,6 +648,10 @@ EXPORT_SYMBOL_GPL(usb_kill_urb); * with error -EPERM. Thus even if the URB's completion handler always * tries to resubmit, it will not succeed and the URB will become idle. * + * The URB must not be deallocated while this routine is running. In + * particular, when a driver calls this routine, it must insure that the + * completion handler cannot deallocate the URB. + * * This routine may not be used in an interrupt context (such as a bottom * half or a completion handler), or when holding a spinlock, or in other * situations where the caller can't schedule(). diff --git a/drivers/usb/gadget/Kconfig b/drivers/usb/gadget/Kconfig index c14a3972953a..2633f7595116 100644 --- a/drivers/usb/gadget/Kconfig +++ b/drivers/usb/gadget/Kconfig @@ -137,7 +137,7 @@ choice config USB_AT91 tristate "Atmel AT91 USB Device Port" - depends on ARCH_AT91 && !ARCH_AT91SAM9RL && !ARCH_AT91CAP9 && !ARCH_AT91SAM9G45 + depends on ARCH_AT91 help Many Atmel AT91 processors (such as the AT91RM2000) have a full speed USB Device Port with support for five configurable @@ -150,7 +150,7 @@ config USB_AT91 config USB_ATMEL_USBA tristate "Atmel USBA" select USB_GADGET_DUALSPEED - depends on AVR32 || ARCH_AT91CAP9 || ARCH_AT91SAM9RL || ARCH_AT91SAM9G45 + depends on AVR32 || ARCH_AT91SAM9RL || ARCH_AT91SAM9G45 help USBA is the integrated high-speed USB Device controller on the AT32AP700x, some AT91SAM9 and AT91CAP9 processors from Atmel. @@ -284,7 +284,7 @@ config USB_IMX config USB_S3C2410 tristate "S3C2410 USB Device Controller" - depends on ARCH_S3C2410 + depends on ARCH_S3C24XX help Samsung's S3C2410 is an ARM-4 processor with an integrated full speed USB 1.1 device controller. It has 4 configurable @@ -299,7 +299,7 @@ config USB_S3C2410_DEBUG config USB_S3C_HSUDC tristate "S3C2416, S3C2443 and S3C2450 USB Device Controller" - depends on ARCH_S3C2410 + depends on ARCH_S3C24XX select USB_GADGET_DUALSPEED help Samsung's S3C2416, S3C2443 and S3C2450 is an ARM9 based SoC diff --git a/drivers/usb/gadget/amd5536udc.c b/drivers/usb/gadget/amd5536udc.c index 2204a4c68d85..77779271f487 100644 --- a/drivers/usb/gadget/amd5536udc.c +++ b/drivers/usb/gadget/amd5536udc.c @@ -54,7 +54,6 @@ #include <linux/prefetch.h> #include <asm/byteorder.h> -#include <asm/system.h> #include <asm/unaligned.h> /* gadget stack */ diff --git a/drivers/usb/gadget/at91_udc.c b/drivers/usb/gadget/at91_udc.c index 15a8cdb2ded5..0c935d7c65bd 100644 --- a/drivers/usb/gadget/at91_udc.c +++ b/drivers/usb/gadget/at91_udc.c @@ -29,17 +29,19 @@ #include <linux/clk.h> #include <linux/usb/ch9.h> #include <linux/usb/gadget.h> +#include <linux/of.h> +#include <linux/of_gpio.h> #include <asm/byteorder.h> #include <mach/hardware.h> #include <asm/io.h> #include <asm/irq.h> -#include <asm/system.h> #include <asm/gpio.h> #include <mach/board.h> #include <mach/cpu.h> #include <mach/at91sam9261_matrix.h> +#include <mach/at91_matrix.h> #include "at91_udc.h" @@ -910,9 +912,9 @@ static void pullup(struct at91_udc *udc, int is_on) } else if (cpu_is_at91sam9261() || cpu_is_at91sam9g10()) { u32 usbpucr; - usbpucr = at91_sys_read(AT91_MATRIX_USBPUCR); + usbpucr = at91_matrix_read(AT91_MATRIX_USBPUCR); usbpucr |= AT91_MATRIX_USBPUCR_PUON; - at91_sys_write(AT91_MATRIX_USBPUCR, usbpucr); + at91_matrix_write(AT91_MATRIX_USBPUCR, usbpucr); } } else { stop_activity(udc); @@ -928,9 +930,9 @@ static void pullup(struct at91_udc *udc, int is_on) } else if (cpu_is_at91sam9261() || cpu_is_at91sam9g10()) { u32 usbpucr; - usbpucr = at91_sys_read(AT91_MATRIX_USBPUCR); + usbpucr = at91_matrix_read(AT91_MATRIX_USBPUCR); usbpucr &= ~AT91_MATRIX_USBPUCR_PUON; - at91_sys_write(AT91_MATRIX_USBPUCR, usbpucr); + at91_matrix_write(AT91_MATRIX_USBPUCR, usbpucr); } clk_off(udc); } @@ -1706,7 +1708,27 @@ static void at91udc_shutdown(struct platform_device *dev) spin_unlock_irqrestore(&udc->lock, flags); } -static int __init at91udc_probe(struct platform_device *pdev) +static void __devinit at91udc_of_init(struct at91_udc *udc, + struct device_node *np) +{ + struct at91_udc_data *board = &udc->board; + u32 val; + enum of_gpio_flags flags; + + if (of_property_read_u32(np, "atmel,vbus-polled", &val) == 0) + board->vbus_polled = 1; + + board->vbus_pin = of_get_named_gpio_flags(np, "atmel,vbus-gpio", 0, + &flags); + board->vbus_active_low = (flags & OF_GPIO_ACTIVE_LOW) ? 1 : 0; + + board->pullup_pin = of_get_named_gpio_flags(np, "atmel,pullup-gpio", 0, + &flags); + + board->pullup_active_low = (flags & OF_GPIO_ACTIVE_LOW) ? 1 : 0; +} + +static int __devinit at91udc_probe(struct platform_device *pdev) { struct device *dev = &pdev->dev; struct at91_udc *udc; @@ -1741,7 +1763,11 @@ static int __init at91udc_probe(struct platform_device *pdev) /* init software state */ udc = &controller; udc->gadget.dev.parent = dev; - udc->board = *(struct at91_udc_data *) dev->platform_data; + if (pdev->dev.of_node) + at91udc_of_init(udc, pdev->dev.of_node); + else + memcpy(&udc->board, dev->platform_data, + sizeof(struct at91_udc_data)); udc->pdev = pdev; udc->enabled = 0; spin_lock_init(&udc->lock); @@ -1970,6 +1996,15 @@ static int at91udc_resume(struct platform_device *pdev) #define at91udc_resume NULL #endif +#if defined(CONFIG_OF) +static const struct of_device_id at91_udc_dt_ids[] = { + { .compatible = "atmel,at91rm9200-udc" }, + { /* sentinel */ } +}; + +MODULE_DEVICE_TABLE(of, at91_udc_dt_ids); +#endif + static struct platform_driver at91_udc_driver = { .remove = __exit_p(at91udc_remove), .shutdown = at91udc_shutdown, @@ -1978,6 +2013,7 @@ static struct platform_driver at91_udc_driver = { .driver = { .name = (char *) driver_name, .owner = THIS_MODULE, + .of_match_table = of_match_ptr(at91_udc_dt_ids), }, }; diff --git a/drivers/usb/gadget/atmel_usba_udc.c b/drivers/usb/gadget/atmel_usba_udc.c index 5e10f651ad63..9f98508966d1 100644 --- a/drivers/usb/gadget/atmel_usba_udc.c +++ b/drivers/usb/gadget/atmel_usba_udc.c @@ -332,12 +332,12 @@ static int vbus_is_present(struct usba_udc *udc) static void toggle_bias(int is_on) { - unsigned int uckr = at91_sys_read(AT91_CKGR_UCKR); + unsigned int uckr = at91_pmc_read(AT91_CKGR_UCKR); if (is_on) - at91_sys_write(AT91_CKGR_UCKR, uckr | AT91_PMC_BIASEN); + at91_pmc_write(AT91_CKGR_UCKR, uckr | AT91_PMC_BIASEN); else - at91_sys_write(AT91_CKGR_UCKR, uckr & ~(AT91_PMC_BIASEN)); + at91_pmc_write(AT91_CKGR_UCKR, uckr & ~(AT91_PMC_BIASEN)); } #else diff --git a/drivers/usb/gadget/dummy_hcd.c b/drivers/usb/gadget/dummy_hcd.c index e1cd56c5e2a8..a6dfd2164166 100644 --- a/drivers/usb/gadget/dummy_hcd.c +++ b/drivers/usb/gadget/dummy_hcd.c @@ -44,7 +44,6 @@ #include <asm/byteorder.h> #include <linux/io.h> #include <asm/irq.h> -#include <asm/system.h> #include <asm/unaligned.h> #define DRIVER_DESC "USB Host+Gadget Emulator" diff --git a/drivers/usb/gadget/f_fs.c b/drivers/usb/gadget/f_fs.c index 7f445ec723bc..1cbba70836bc 100644 --- a/drivers/usb/gadget/f_fs.c +++ b/drivers/usb/gadget/f_fs.c @@ -1063,13 +1063,9 @@ static int ffs_sb_fill(struct super_block *sb, void *_data, int silent) &simple_dir_operations, &simple_dir_inode_operations, &data->perms); - if (unlikely(!inode)) + sb->s_root = d_make_root(inode); + if (unlikely(!sb->s_root)) goto Enomem; - sb->s_root = d_alloc_root(inode); - if (unlikely(!sb->s_root)) { - iput(inode); - goto Enomem; - } /* EP0 file */ if (unlikely(!ffs_sb_create_file(sb, "ep0", ffs, diff --git a/drivers/usb/gadget/f_phonet.c b/drivers/usb/gadget/f_phonet.c index 7cdcb63b21ff..965a6293206a 100644 --- a/drivers/usb/gadget/f_phonet.c +++ b/drivers/usb/gadget/f_phonet.c @@ -345,7 +345,7 @@ static void pn_rx_complete(struct usb_ep *ep, struct usb_request *req) } skb_add_rx_frag(skb, skb_shinfo(skb)->nr_frags, page, - skb->len <= 1, req->actual); + skb->len <= 1, req->actual, PAGE_SIZE); page = NULL; if (req->actual < req->length) { /* Last fragment */ diff --git a/drivers/usb/gadget/fsl_udc_core.c b/drivers/usb/gadget/fsl_udc_core.c index b30e21fdbb1b..5f94e79cd6b9 100644 --- a/drivers/usb/gadget/fsl_udc_core.c +++ b/drivers/usb/gadget/fsl_udc_core.c @@ -43,7 +43,6 @@ #include <asm/byteorder.h> #include <asm/io.h> -#include <asm/system.h> #include <asm/unaligned.h> #include <asm/dma.h> diff --git a/drivers/usb/gadget/goku_udc.c b/drivers/usb/gadget/goku_udc.c index e1dfd32dc805..e151d6b87dee 100644 --- a/drivers/usb/gadget/goku_udc.c +++ b/drivers/usb/gadget/goku_udc.c @@ -43,7 +43,6 @@ #include <asm/byteorder.h> #include <asm/io.h> #include <asm/irq.h> -#include <asm/system.h> #include <asm/unaligned.h> diff --git a/drivers/usb/gadget/inode.c b/drivers/usb/gadget/inode.c index 4f18a0e46070..e58b16442971 100644 --- a/drivers/usb/gadget/inode.c +++ b/drivers/usb/gadget/inode.c @@ -1571,20 +1571,17 @@ delegate: static void destroy_ep_files (struct dev_data *dev) { - struct list_head *entry, *tmp; - DBG (dev, "%s %d\n", __func__, dev->state); /* dev->state must prevent interference */ -restart: spin_lock_irq (&dev->lock); - list_for_each_safe (entry, tmp, &dev->epfiles) { + while (!list_empty(&dev->epfiles)) { struct ep_data *ep; struct inode *parent; struct dentry *dentry; /* break link to FS */ - ep = list_entry (entry, struct ep_data, epfiles); + ep = list_first_entry (&dev->epfiles, struct ep_data, epfiles); list_del_init (&ep->epfiles); dentry = ep->dentry; ep->dentry = NULL; @@ -1607,8 +1604,7 @@ restart: dput (dentry); mutex_unlock (&parent->i_mutex); - /* fds may still be open */ - goto restart; + spin_lock_irq (&dev->lock); } spin_unlock_irq (&dev->lock); } @@ -2061,10 +2057,8 @@ gadgetfs_fill_super (struct super_block *sb, void *opts, int silent) if (!inode) goto Enomem; inode->i_op = &simple_dir_inode_operations; - if (!(sb->s_root = d_alloc_root (inode))) { - iput(inode); + if (!(sb->s_root = d_make_root (inode))) goto Enomem; - } /* the ep0 file is named after the controller we expect; * user mode code can use it for sanity checks, like we do. diff --git a/drivers/usb/gadget/langwell_udc.c b/drivers/usb/gadget/langwell_udc.c index edd52d963f14..f9cedd52cf20 100644 --- a/drivers/usb/gadget/langwell_udc.c +++ b/drivers/usb/gadget/langwell_udc.c @@ -32,7 +32,6 @@ #include <linux/pm.h> #include <linux/io.h> #include <linux/irq.h> -#include <asm/system.h> #include <asm/unaligned.h> #include "langwell_udc.h" diff --git a/drivers/usb/gadget/mv_udc_core.c b/drivers/usb/gadget/mv_udc_core.c index 19bbe80c2f8c..a73cf406e2a4 100644 --- a/drivers/usb/gadget/mv_udc_core.c +++ b/drivers/usb/gadget/mv_udc_core.c @@ -34,7 +34,6 @@ #include <linux/platform_device.h> #include <linux/clk.h> #include <linux/platform_data/mv_usb.h> -#include <asm/system.h> #include <asm/unaligned.h> #include "mv_udc.h" diff --git a/drivers/usb/gadget/net2272.c b/drivers/usb/gadget/net2272.c index 01ae56f47174..43ac7482fa91 100644 --- a/drivers/usb/gadget/net2272.c +++ b/drivers/usb/gadget/net2272.c @@ -42,7 +42,6 @@ #include <linux/usb/gadget.h> #include <asm/byteorder.h> -#include <asm/system.h> #include <asm/unaligned.h> #include "net2272.h" diff --git a/drivers/usb/gadget/net2280.c b/drivers/usb/gadget/net2280.c index a5ccabc37f30..ac335af154ba 100644 --- a/drivers/usb/gadget/net2280.c +++ b/drivers/usb/gadget/net2280.c @@ -59,7 +59,6 @@ #include <asm/byteorder.h> #include <asm/io.h> #include <asm/irq.h> -#include <asm/system.h> #include <asm/unaligned.h> diff --git a/drivers/usb/gadget/omap_udc.c b/drivers/usb/gadget/omap_udc.c index b44830df593e..3b4b6dd0f95a 100644 --- a/drivers/usb/gadget/omap_udc.c +++ b/drivers/usb/gadget/omap_udc.c @@ -40,7 +40,6 @@ #include <asm/byteorder.h> #include <asm/io.h> #include <asm/irq.h> -#include <asm/system.h> #include <asm/unaligned.h> #include <asm/mach-types.h> diff --git a/drivers/usb/gadget/printer.c b/drivers/usb/gadget/printer.c index d83134b0f78a..4e4dc1f5f388 100644 --- a/drivers/usb/gadget/printer.c +++ b/drivers/usb/gadget/printer.c @@ -34,7 +34,6 @@ #include <asm/byteorder.h> #include <linux/io.h> #include <linux/irq.h> -#include <asm/system.h> #include <linux/uaccess.h> #include <asm/unaligned.h> diff --git a/drivers/usb/gadget/pxa25x_udc.c b/drivers/usb/gadget/pxa25x_udc.c index 1b33634f2736..41ed69c96d8c 100644 --- a/drivers/usb/gadget/pxa25x_udc.c +++ b/drivers/usb/gadget/pxa25x_udc.c @@ -41,7 +41,6 @@ #include <asm/byteorder.h> #include <asm/dma.h> #include <asm/gpio.h> -#include <asm/system.h> #include <asm/mach-types.h> #include <asm/unaligned.h> diff --git a/drivers/usb/gadget/rndis.c b/drivers/usb/gadget/rndis.c index d3cdffea9c8a..73a934a170d1 100644 --- a/drivers/usb/gadget/rndis.c +++ b/drivers/usb/gadget/rndis.c @@ -34,7 +34,6 @@ #include <asm/io.h> #include <asm/byteorder.h> -#include <asm/system.h> #include <asm/unaligned.h> diff --git a/drivers/usb/gadget/s3c2410_udc.c b/drivers/usb/gadget/s3c2410_udc.c index ab9c65e2c1d5..195524cde6c3 100644 --- a/drivers/usb/gadget/s3c2410_udc.c +++ b/drivers/usb/gadget/s3c2410_udc.c @@ -37,7 +37,6 @@ #include <asm/byteorder.h> #include <asm/io.h> #include <asm/irq.h> -#include <asm/system.h> #include <asm/unaligned.h> #include <mach/irqs.h> diff --git a/drivers/usb/host/ehci-atmel.c b/drivers/usb/host/ehci-atmel.c index a5a3ef1f0096..cf14c95a6700 100644 --- a/drivers/usb/host/ehci-atmel.c +++ b/drivers/usb/host/ehci-atmel.c @@ -13,6 +13,8 @@ #include <linux/clk.h> #include <linux/platform_device.h> +#include <linux/of.h> +#include <linux/of_platform.h> /* interface and function clocks */ static struct clk *iclk, *fclk; @@ -115,6 +117,8 @@ static const struct hc_driver ehci_atmel_hc_driver = { .clear_tt_buffer_complete = ehci_clear_tt_buffer_complete, }; +static u64 at91_ehci_dma_mask = DMA_BIT_MASK(32); + static int __devinit ehci_atmel_drv_probe(struct platform_device *pdev) { struct usb_hcd *hcd; @@ -137,6 +141,13 @@ static int __devinit ehci_atmel_drv_probe(struct platform_device *pdev) goto fail_create_hcd; } + /* Right now device-tree probed devices don't get dma_mask set. + * Since shared usb code relies on it, set it here for now. + * Once we have dma capability bindings this can go away. + */ + if (!pdev->dev.dma_mask) + pdev->dev.dma_mask = &at91_ehci_dma_mask; + hcd = usb_create_hcd(driver, &pdev->dev, dev_name(&pdev->dev)); if (!hcd) { retval = -ENOMEM; @@ -225,9 +236,21 @@ static int __devexit ehci_atmel_drv_remove(struct platform_device *pdev) return 0; } +#ifdef CONFIG_OF +static const struct of_device_id atmel_ehci_dt_ids[] = { + { .compatible = "atmel,at91sam9g45-ehci" }, + { /* sentinel */ } +}; + +MODULE_DEVICE_TABLE(of, atmel_ehci_dt_ids); +#endif + static struct platform_driver ehci_atmel_driver = { .probe = ehci_atmel_drv_probe, .remove = __devexit_p(ehci_atmel_drv_remove), .shutdown = usb_hcd_platform_shutdown, - .driver.name = "atmel-ehci", + .driver = { + .name = "atmel-ehci", + .of_match_table = of_match_ptr(atmel_ehci_dt_ids), + }, }; diff --git a/drivers/usb/host/ehci-dbg.c b/drivers/usb/host/ehci-dbg.c index fd9109d7eb0e..680e1a31fb87 100644 --- a/drivers/usb/host/ehci-dbg.c +++ b/drivers/usb/host/ehci-dbg.c @@ -352,7 +352,6 @@ static int debug_async_open(struct inode *, struct file *); static int debug_periodic_open(struct inode *, struct file *); static int debug_registers_open(struct inode *, struct file *); static int debug_async_open(struct inode *, struct file *); -static int debug_lpm_open(struct inode *, struct file *); static ssize_t debug_lpm_read(struct file *file, char __user *user_buf, size_t count, loff_t *ppos); static ssize_t debug_lpm_write(struct file *file, const char __user *buffer, @@ -385,7 +384,7 @@ static const struct file_operations debug_registers_fops = { }; static const struct file_operations debug_lpm_fops = { .owner = THIS_MODULE, - .open = debug_lpm_open, + .open = simple_open, .read = debug_lpm_read, .write = debug_lpm_write, .release = debug_lpm_close, @@ -970,12 +969,6 @@ static int debug_registers_open(struct inode *inode, struct file *file) return file->private_data ? 0 : -ENOMEM; } -static int debug_lpm_open(struct inode *inode, struct file *file) -{ - file->private_data = inode->i_private; - return 0; -} - static int debug_lpm_close(struct inode *inode, struct file *file) { return 0; diff --git a/drivers/usb/host/ehci-hcd.c b/drivers/usb/host/ehci-hcd.c index aede6374e4b6..806cc95317aa 100644 --- a/drivers/usb/host/ehci-hcd.c +++ b/drivers/usb/host/ehci-hcd.c @@ -45,7 +45,6 @@ #include <asm/byteorder.h> #include <asm/io.h> #include <asm/irq.h> -#include <asm/system.h> #include <asm/unaligned.h> #if defined(CONFIG_PPC_PS3) @@ -348,6 +347,8 @@ static int ehci_reset (struct ehci_hcd *ehci) if (ehci->debug) dbgp_external_startup(); + ehci->port_c_suspend = ehci->suspended_ports = + ehci->resuming_ports = 0; return retval; } @@ -940,6 +941,7 @@ static irqreturn_t ehci_irq (struct usb_hcd *hcd) * like usb_port_resume() does. */ ehci->reset_done[i] = jiffies + msecs_to_jiffies(25); + set_bit(i, &ehci->resuming_ports); ehci_dbg (ehci, "port %d remote wakeup\n", i + 1); mod_timer(&hcd->rh_timer, ehci->reset_done[i]); } diff --git a/drivers/usb/host/ehci-hub.c b/drivers/usb/host/ehci-hub.c index 256fbd42e48c..38fe07623152 100644 --- a/drivers/usb/host/ehci-hub.c +++ b/drivers/usb/host/ehci-hub.c @@ -223,15 +223,10 @@ static int ehci_bus_suspend (struct usb_hcd *hcd) * remote wakeup, we must fail the suspend. */ if (hcd->self.root_hub->do_remote_wakeup) { - port = HCS_N_PORTS(ehci->hcs_params); - while (port--) { - if (ehci->reset_done[port] != 0) { - spin_unlock_irq(&ehci->lock); - ehci_dbg(ehci, "suspend failed because " - "port %d is resuming\n", - port + 1); - return -EBUSY; - } + if (ehci->resuming_ports) { + spin_unlock_irq(&ehci->lock); + ehci_dbg(ehci, "suspend failed because a port is resuming\n"); + return -EBUSY; } } @@ -554,16 +549,12 @@ static int ehci_hub_status_data (struct usb_hcd *hcd, char *buf) { struct ehci_hcd *ehci = hcd_to_ehci (hcd); - u32 temp, status = 0; + u32 temp, status; u32 mask; int ports, i, retval = 1; unsigned long flags; u32 ppcd = 0; - /* if !USB_SUSPEND, root hub timers won't get shut down ... */ - if (ehci->rh_state != EHCI_RH_RUNNING) - return 0; - /* init status to no-changes */ buf [0] = 0; ports = HCS_N_PORTS (ehci->hcs_params); @@ -572,6 +563,11 @@ ehci_hub_status_data (struct usb_hcd *hcd, char *buf) retval++; } + /* Inform the core about resumes-in-progress by returning + * a non-zero value even if there are no status changes. + */ + status = ehci->resuming_ports; + /* Some boards (mostly VIA?) report bogus overcurrent indications, * causing massive log spam unless we completely ignore them. It * may be relevant that VIA VT8235 controllers, where PORT_POWER is @@ -846,6 +842,7 @@ static int ehci_hub_control ( ehci_writel(ehci, temp & ~(PORT_RWC_BITS | PORT_RESUME), status_reg); + clear_bit(wIndex, &ehci->resuming_ports); retval = handshake(ehci, status_reg, PORT_RESUME, 0, 2000 /* 2msec */); if (retval != 0) { @@ -864,6 +861,7 @@ static int ehci_hub_control ( ehci->reset_done[wIndex])) { status |= USB_PORT_STAT_C_RESET << 16; ehci->reset_done [wIndex] = 0; + clear_bit(wIndex, &ehci->resuming_ports); /* force reset to complete */ ehci_writel(ehci, temp & ~(PORT_RWC_BITS | PORT_RESET), @@ -884,8 +882,10 @@ static int ehci_hub_control ( ehci_readl(ehci, status_reg)); } - if (!(temp & (PORT_RESUME|PORT_RESET))) + if (!(temp & (PORT_RESUME|PORT_RESET))) { ehci->reset_done[wIndex] = 0; + clear_bit(wIndex, &ehci->resuming_ports); + } /* transfer dedicated ports to the companion hc */ if ((temp & PORT_CONNECT) && @@ -920,6 +920,7 @@ static int ehci_hub_control ( status |= USB_PORT_STAT_SUSPEND; } else if (test_bit(wIndex, &ehci->suspended_ports)) { clear_bit(wIndex, &ehci->suspended_ports); + clear_bit(wIndex, &ehci->resuming_ports); ehci->reset_done[wIndex] = 0; if (temp & PORT_PE) set_bit(wIndex, &ehci->port_c_suspend); diff --git a/drivers/usb/host/ehci-tegra.c b/drivers/usb/host/ehci-tegra.c index 3de48a2d7955..73544bd440bd 100644 --- a/drivers/usb/host/ehci-tegra.c +++ b/drivers/usb/host/ehci-tegra.c @@ -224,6 +224,7 @@ static int tegra_ehci_hub_control( temp &= ~(PORT_RWC_BITS | PORT_WAKE_BITS); /* start resume signalling */ ehci_writel(ehci, temp | PORT_RESUME, status_reg); + set_bit(wIndex-1, &ehci->resuming_ports); spin_unlock_irqrestore(&ehci->lock, flags); msleep(20); @@ -236,6 +237,7 @@ static int tegra_ehci_hub_control( pr_err("%s: timeout waiting for SUSPEND\n", __func__); ehci->reset_done[wIndex-1] = 0; + clear_bit(wIndex-1, &ehci->resuming_ports); tegra->port_resuming = 1; goto done; diff --git a/drivers/usb/host/ehci.h b/drivers/usb/host/ehci.h index 8f9acbc96fde..2694ed6558d2 100644 --- a/drivers/usb/host/ehci.h +++ b/drivers/usb/host/ehci.h @@ -117,6 +117,8 @@ struct ehci_hcd { /* one per controller */ the change-suspend feature turned on */ unsigned long suspended_ports; /* which ports are suspended */ + unsigned long resuming_ports; /* which ports have + started to resume */ /* per-HC memory pools (could be per-bus, but ...) */ struct dma_pool *qh_pool; /* qh per active urb */ diff --git a/drivers/usb/host/isp116x-hcd.c b/drivers/usb/host/isp116x-hcd.c index 924880087a74..9e65e3091c8a 100644 --- a/drivers/usb/host/isp116x-hcd.c +++ b/drivers/usb/host/isp116x-hcd.c @@ -70,7 +70,6 @@ #include <asm/io.h> #include <asm/irq.h> -#include <asm/system.h> #include <asm/byteorder.h> #include "isp116x.h" diff --git a/drivers/usb/host/isp1362-hcd.c b/drivers/usb/host/isp1362-hcd.c index 9e63cdf1ab75..2ed112d3e159 100644 --- a/drivers/usb/host/isp1362-hcd.c +++ b/drivers/usb/host/isp1362-hcd.c @@ -84,7 +84,6 @@ #include <linux/prefetch.h> #include <asm/irq.h> -#include <asm/system.h> #include <asm/byteorder.h> #include <asm/unaligned.h> diff --git a/drivers/usb/host/ohci-at91.c b/drivers/usb/host/ohci-at91.c index 77afabc77f9b..09f597ad6e00 100644 --- a/drivers/usb/host/ohci-at91.c +++ b/drivers/usb/host/ohci-at91.c @@ -14,6 +14,8 @@ #include <linux/clk.h> #include <linux/platform_device.h> +#include <linux/of_platform.h> +#include <linux/of_gpio.h> #include <mach/hardware.h> #include <asm/gpio.h> @@ -25,6 +27,10 @@ #error "CONFIG_ARCH_AT91 must be defined." #endif +#define valid_port(index) ((index) >= 0 && (index) < AT91_MAX_USBH_PORTS) +#define at91_for_each_port(index) \ + for ((index) = 0; (index) < AT91_MAX_USBH_PORTS; (index)++) + /* interface and function clocks; sometimes also an AHB clock */ static struct clk *iclk, *fclk, *hclk; static int clocked; @@ -238,26 +244,26 @@ ohci_at91_start (struct usb_hcd *hcd) static void ohci_at91_usb_set_power(struct at91_usbh_data *pdata, int port, int enable) { - if (port < 0 || port >= 2) + if (!valid_port(port)) return; if (!gpio_is_valid(pdata->vbus_pin[port])) return; gpio_set_value(pdata->vbus_pin[port], - !pdata->vbus_pin_active_low[port] ^ enable); + pdata->vbus_pin_active_low[port] ^ enable); } static int ohci_at91_usb_get_power(struct at91_usbh_data *pdata, int port) { - if (port < 0 || port >= 2) + if (!valid_port(port)) return -EINVAL; if (!gpio_is_valid(pdata->vbus_pin[port])) return -EINVAL; return gpio_get_value(pdata->vbus_pin[port]) ^ - !pdata->vbus_pin_active_low[port]; + pdata->vbus_pin_active_low[port]; } /* @@ -269,9 +275,9 @@ static int ohci_at91_hub_status_data(struct usb_hcd *hcd, char *buf) int length = ohci_hub_status_data(hcd, buf); int port; - for (port = 0; port < ARRAY_SIZE(pdata->overcurrent_pin); port++) { + at91_for_each_port(port) { if (pdata->overcurrent_changed[port]) { - if (! length) + if (!length) length = 1; buf[0] |= 1 << (port + 1); } @@ -295,11 +301,17 @@ static int ohci_at91_hub_control(struct usb_hcd *hcd, u16 typeReq, u16 wValue, "ohci_at91_hub_control(%p,0x%04x,0x%04x,0x%04x,%p,%04x)\n", hcd, typeReq, wValue, wIndex, buf, wLength); + wIndex--; + switch (typeReq) { case SetPortFeature: if (wValue == USB_PORT_FEAT_POWER) { dev_dbg(hcd->self.controller, "SetPortFeat: POWER\n"); - ohci_at91_usb_set_power(pdata, wIndex - 1, 1); + if (valid_port(wIndex)) { + ohci_at91_usb_set_power(pdata, wIndex, 1); + ret = 0; + } + goto out; } break; @@ -310,9 +322,9 @@ static int ohci_at91_hub_control(struct usb_hcd *hcd, u16 typeReq, u16 wValue, dev_dbg(hcd->self.controller, "ClearPortFeature: C_OVER_CURRENT\n"); - if (wIndex == 1 || wIndex == 2) { - pdata->overcurrent_changed[wIndex-1] = 0; - pdata->overcurrent_status[wIndex-1] = 0; + if (valid_port(wIndex)) { + pdata->overcurrent_changed[wIndex] = 0; + pdata->overcurrent_status[wIndex] = 0; } goto out; @@ -321,9 +333,8 @@ static int ohci_at91_hub_control(struct usb_hcd *hcd, u16 typeReq, u16 wValue, dev_dbg(hcd->self.controller, "ClearPortFeature: OVER_CURRENT\n"); - if (wIndex == 1 || wIndex == 2) { - pdata->overcurrent_status[wIndex-1] = 0; - } + if (valid_port(wIndex)) + pdata->overcurrent_status[wIndex] = 0; goto out; @@ -331,15 +342,15 @@ static int ohci_at91_hub_control(struct usb_hcd *hcd, u16 typeReq, u16 wValue, dev_dbg(hcd->self.controller, "ClearPortFeature: POWER\n"); - if (wIndex == 1 || wIndex == 2) { - ohci_at91_usb_set_power(pdata, wIndex - 1, 0); + if (valid_port(wIndex)) { + ohci_at91_usb_set_power(pdata, wIndex, 0); return 0; } } break; } - ret = ohci_hub_control(hcd, typeReq, wValue, wIndex, buf, wLength); + ret = ohci_hub_control(hcd, typeReq, wValue, wIndex + 1, buf, wLength); if (ret) goto out; @@ -375,18 +386,15 @@ static int ohci_at91_hub_control(struct usb_hcd *hcd, u16 typeReq, u16 wValue, dev_dbg(hcd->self.controller, "GetPortStatus(%d)\n", wIndex); - if (wIndex == 1 || wIndex == 2) { - if (! ohci_at91_usb_get_power(pdata, wIndex-1)) { + if (valid_port(wIndex)) { + if (!ohci_at91_usb_get_power(pdata, wIndex)) *data &= ~cpu_to_le32(RH_PS_PPS); - } - if (pdata->overcurrent_changed[wIndex-1]) { + if (pdata->overcurrent_changed[wIndex]) *data |= cpu_to_le32(RH_PS_OCIC); - } - if (pdata->overcurrent_status[wIndex-1]) { + if (pdata->overcurrent_status[wIndex]) *data |= cpu_to_le32(RH_PS_POCI); - } } } @@ -448,13 +456,14 @@ static irqreturn_t ohci_hcd_at91_overcurrent_irq(int irq, void *data) /* From the GPIO notifying the over-current situation, find * out the corresponding port */ - gpio = irq_to_gpio(irq); - for (port = 0; port < ARRAY_SIZE(pdata->overcurrent_pin); port++) { - if (pdata->overcurrent_pin[port] == gpio) + at91_for_each_port(port) { + if (gpio_to_irq(pdata->overcurrent_pin[port]) == irq) { + gpio = pdata->overcurrent_pin[port]; break; + } } - if (port == ARRAY_SIZE(pdata->overcurrent_pin)) { + if (port == AT91_MAX_USBH_PORTS) { dev_err(& pdev->dev, "overcurrent interrupt from unknown GPIO\n"); return IRQ_HANDLED; } @@ -464,7 +473,7 @@ static irqreturn_t ohci_hcd_at91_overcurrent_irq(int irq, void *data) /* When notified of an over-current situation, disable power on the corresponding port, and mark this port in over-current. */ - if (! val) { + if (!val) { ohci_at91_usb_set_power(pdata, port, 0); pdata->overcurrent_status[port] = 1; pdata->overcurrent_changed[port] = 1; @@ -476,34 +485,133 @@ static irqreturn_t ohci_hcd_at91_overcurrent_irq(int irq, void *data) return IRQ_HANDLED; } +#ifdef CONFIG_OF +static const struct of_device_id at91_ohci_dt_ids[] = { + { .compatible = "atmel,at91rm9200-ohci" }, + { /* sentinel */ } +}; + +MODULE_DEVICE_TABLE(of, at91_ohci_dt_ids); + +static u64 at91_ohci_dma_mask = DMA_BIT_MASK(32); + +static int __devinit ohci_at91_of_init(struct platform_device *pdev) +{ + struct device_node *np = pdev->dev.of_node; + int i, gpio; + enum of_gpio_flags flags; + struct at91_usbh_data *pdata; + u32 ports; + + if (!np) + return 0; + + /* Right now device-tree probed devices don't get dma_mask set. + * Since shared usb code relies on it, set it here for now. + * Once we have dma capability bindings this can go away. + */ + if (!pdev->dev.dma_mask) + pdev->dev.dma_mask = &at91_ohci_dma_mask; + + pdata = devm_kzalloc(&pdev->dev, sizeof(*pdata), GFP_KERNEL); + if (!pdata) + return -ENOMEM; + + if (!of_property_read_u32(np, "num-ports", &ports)) + pdata->ports = ports; + + at91_for_each_port(i) { + gpio = of_get_named_gpio_flags(np, "atmel,vbus-gpio", i, &flags); + pdata->vbus_pin[i] = gpio; + if (!gpio_is_valid(gpio)) + continue; + pdata->vbus_pin_active_low[i] = flags & OF_GPIO_ACTIVE_LOW; + } + + at91_for_each_port(i) + pdata->overcurrent_pin[i] = + of_get_named_gpio_flags(np, "atmel,oc-gpio", i, &flags); + + pdev->dev.platform_data = pdata; + + return 0; +} +#else +static int __devinit ohci_at91_of_init(struct platform_device *pdev) +{ + return 0; +} +#endif + /*-------------------------------------------------------------------------*/ static int ohci_hcd_at91_drv_probe(struct platform_device *pdev) { - struct at91_usbh_data *pdata = pdev->dev.platform_data; + struct at91_usbh_data *pdata; int i; + int gpio; + int ret; + + ret = ohci_at91_of_init(pdev); + if (ret) + return ret; + + pdata = pdev->dev.platform_data; if (pdata) { - for (i = 0; i < ARRAY_SIZE(pdata->vbus_pin); i++) { + at91_for_each_port(i) { if (!gpio_is_valid(pdata->vbus_pin[i])) continue; - gpio_request(pdata->vbus_pin[i], "ohci_vbus"); + gpio = pdata->vbus_pin[i]; + + ret = gpio_request(gpio, "ohci_vbus"); + if (ret) { + dev_err(&pdev->dev, + "can't request vbus gpio %d\n", gpio); + continue; + } + ret = gpio_direction_output(gpio, + !pdata->vbus_pin_active_low[i]); + if (ret) { + dev_err(&pdev->dev, + "can't put vbus gpio %d as output %d\n", + gpio, !pdata->vbus_pin_active_low[i]); + gpio_free(gpio); + continue; + } + ohci_at91_usb_set_power(pdata, i, 1); } - for (i = 0; i < ARRAY_SIZE(pdata->overcurrent_pin); i++) { - int ret; - + at91_for_each_port(i) { if (!gpio_is_valid(pdata->overcurrent_pin[i])) continue; - gpio_request(pdata->overcurrent_pin[i], "ohci_overcurrent"); + gpio = pdata->overcurrent_pin[i]; + + ret = gpio_request(gpio, "ohci_overcurrent"); + if (ret) { + dev_err(&pdev->dev, + "can't request overcurrent gpio %d\n", + gpio); + continue; + } + + ret = gpio_direction_input(gpio); + if (ret) { + dev_err(&pdev->dev, + "can't configure overcurrent gpio %d as input\n", + gpio); + gpio_free(gpio); + continue; + } - ret = request_irq(gpio_to_irq(pdata->overcurrent_pin[i]), + ret = request_irq(gpio_to_irq(gpio), ohci_hcd_at91_overcurrent_irq, IRQF_SHARED, "ohci_overcurrent", pdev); if (ret) { - gpio_free(pdata->overcurrent_pin[i]); - dev_warn(& pdev->dev, "cannot get GPIO IRQ for overcurrent\n"); + gpio_free(gpio); + dev_err(&pdev->dev, + "can't get gpio IRQ for overcurrent\n"); } } } @@ -518,14 +626,14 @@ static int ohci_hcd_at91_drv_remove(struct platform_device *pdev) int i; if (pdata) { - for (i = 0; i < ARRAY_SIZE(pdata->vbus_pin); i++) { + at91_for_each_port(i) { if (!gpio_is_valid(pdata->vbus_pin[i])) continue; ohci_at91_usb_set_power(pdata, i, 0); gpio_free(pdata->vbus_pin[i]); } - for (i = 0; i < ARRAY_SIZE(pdata->overcurrent_pin); i++) { + at91_for_each_port(i) { if (!gpio_is_valid(pdata->overcurrent_pin[i])) continue; free_irq(gpio_to_irq(pdata->overcurrent_pin[i]), pdev); @@ -595,5 +703,6 @@ static struct platform_driver ohci_hcd_at91_driver = { .driver = { .name = "at91_ohci", .owner = THIS_MODULE, + .of_match_table = of_match_ptr(at91_ohci_dt_ids), }, }; diff --git a/drivers/usb/host/ohci-hcd.c b/drivers/usb/host/ohci-hcd.c index cd5e382db89c..235171f29460 100644 --- a/drivers/usb/host/ohci-hcd.c +++ b/drivers/usb/host/ohci-hcd.c @@ -42,7 +42,6 @@ #include <asm/io.h> #include <asm/irq.h> -#include <asm/system.h> #include <asm/unaligned.h> #include <asm/byteorder.h> @@ -1000,7 +999,7 @@ MODULE_LICENSE ("GPL"); #define SA1111_DRIVER ohci_hcd_sa1111_driver #endif -#if defined(CONFIG_ARCH_S3C2410) || defined(CONFIG_ARCH_S3C64XX) +#if defined(CONFIG_ARCH_S3C24XX) || defined(CONFIG_ARCH_S3C64XX) #include "ohci-s3c2410.c" #define PLATFORM_DRIVER ohci_hcd_s3c2410_driver #endif diff --git a/drivers/usb/host/ohci-sa1111.c b/drivers/usb/host/ohci-sa1111.c index 4bde4f9821ba..e1004fb37bd9 100644 --- a/drivers/usb/host/ohci-sa1111.c +++ b/drivers/usb/host/ohci-sa1111.c @@ -16,29 +16,115 @@ #include <mach/hardware.h> #include <asm/mach-types.h> #include <mach/assabet.h> -#include <mach/badge4.h> #include <asm/hardware/sa1111.h> #ifndef CONFIG_SA1111 #error "This file is SA-1111 bus glue. CONFIG_SA1111 must be defined." #endif -extern int usb_disabled(void); +#define USB_STATUS 0x0118 +#define USB_RESET 0x011c +#define USB_IRQTEST 0x0120 + +#define USB_RESET_FORCEIFRESET (1 << 0) +#define USB_RESET_FORCEHCRESET (1 << 1) +#define USB_RESET_CLKGENRESET (1 << 2) +#define USB_RESET_SIMSCALEDOWN (1 << 3) +#define USB_RESET_USBINTTEST (1 << 4) +#define USB_RESET_SLEEPSTBYEN (1 << 5) +#define USB_RESET_PWRSENSELOW (1 << 6) +#define USB_RESET_PWRCTRLLOW (1 << 7) + +#define USB_STATUS_IRQHCIRMTWKUP (1 << 7) +#define USB_STATUS_IRQHCIBUFFACC (1 << 8) +#define USB_STATUS_NIRQHCIM (1 << 9) +#define USB_STATUS_NHCIMFCLR (1 << 10) +#define USB_STATUS_USBPWRSENSE (1 << 11) -/*-------------------------------------------------------------------------*/ +#if 0 +static void dump_hci_status(struct usb_hcd *hcd, const char *label) +{ + unsigned long status = sa1111_readl(hcd->regs + USB_STATUS); + + dbg("%s USB_STATUS = { %s%s%s%s%s}", label, + ((status & USB_STATUS_IRQHCIRMTWKUP) ? "IRQHCIRMTWKUP " : ""), + ((status & USB_STATUS_IRQHCIBUFFACC) ? "IRQHCIBUFFACC " : ""), + ((status & USB_STATUS_NIRQHCIM) ? "" : "IRQHCIM "), + ((status & USB_STATUS_NHCIMFCLR) ? "" : "HCIMFCLR "), + ((status & USB_STATUS_USBPWRSENSE) ? "USBPWRSENSE " : "")); +} +#endif -static void sa1111_start_hc(struct sa1111_dev *dev) +static int ohci_sa1111_reset(struct usb_hcd *hcd) { - unsigned int usb_rst = 0; + struct ohci_hcd *ohci = hcd_to_ohci(hcd); + + ohci_hcd_init(ohci); + return ohci_init(ohci); +} - printk(KERN_DEBUG "%s: starting SA-1111 OHCI USB Controller\n", - __FILE__); +static int __devinit ohci_sa1111_start(struct usb_hcd *hcd) +{ + struct ohci_hcd *ohci = hcd_to_ohci(hcd); + int ret; -#ifdef CONFIG_SA1100_BADGE4 - if (machine_is_badge4()) { - badge4_set_5V(BADGE4_5V_USB, 1); + ret = ohci_run(ohci); + if (ret < 0) { + ohci_err(ohci, "can't start\n"); + ohci_stop(hcd); } + return ret; +} + +static const struct hc_driver ohci_sa1111_hc_driver = { + .description = hcd_name, + .product_desc = "SA-1111 OHCI", + .hcd_priv_size = sizeof(struct ohci_hcd), + + /* + * generic hardware linkage + */ + .irq = ohci_irq, + .flags = HCD_USB11 | HCD_MEMORY, + + /* + * basic lifecycle operations + */ + .reset = ohci_sa1111_reset, + .start = ohci_sa1111_start, + .stop = ohci_stop, + .shutdown = ohci_shutdown, + + /* + * managing i/o requests and associated device resources + */ + .urb_enqueue = ohci_urb_enqueue, + .urb_dequeue = ohci_urb_dequeue, + .endpoint_disable = ohci_endpoint_disable, + + /* + * scheduling support + */ + .get_frame_number = ohci_get_frame, + + /* + * root hub support + */ + .hub_status_data = ohci_hub_status_data, + .hub_control = ohci_hub_control, +#ifdef CONFIG_PM + .bus_suspend = ohci_bus_suspend, + .bus_resume = ohci_bus_resume, #endif + .start_port_reset = ohci_start_port_reset, +}; + +static int sa1111_start_hc(struct sa1111_dev *dev) +{ + unsigned int usb_rst = 0; + int ret; + + dev_dbg(&dev->dev, "starting SA-1111 OHCI USB Controller\n"); if (machine_is_xp860() || machine_has_neponset() || @@ -51,220 +137,121 @@ static void sa1111_start_hc(struct sa1111_dev *dev) * host controller in reset. */ sa1111_writel(usb_rst | USB_RESET_FORCEIFRESET | USB_RESET_FORCEHCRESET, - dev->mapbase + SA1111_USB_RESET); + dev->mapbase + USB_RESET); /* * Now, carefully enable the USB clock, and take * the USB host controller out of reset. */ - sa1111_enable_device(dev); - udelay(11); - sa1111_writel(usb_rst, dev->mapbase + SA1111_USB_RESET); + ret = sa1111_enable_device(dev); + if (ret == 0) { + udelay(11); + sa1111_writel(usb_rst, dev->mapbase + USB_RESET); + } + + return ret; } static void sa1111_stop_hc(struct sa1111_dev *dev) { unsigned int usb_rst; - printk(KERN_DEBUG "%s: stopping SA-1111 OHCI USB Controller\n", - __FILE__); + + dev_dbg(&dev->dev, "stopping SA-1111 OHCI USB Controller\n"); /* * Put the USB host controller into reset. */ - usb_rst = sa1111_readl(dev->mapbase + SA1111_USB_RESET); + usb_rst = sa1111_readl(dev->mapbase + USB_RESET); sa1111_writel(usb_rst | USB_RESET_FORCEIFRESET | USB_RESET_FORCEHCRESET, - dev->mapbase + SA1111_USB_RESET); + dev->mapbase + USB_RESET); /* * Stop the USB clock. */ sa1111_disable_device(dev); - -#ifdef CONFIG_SA1100_BADGE4 - if (machine_is_badge4()) { - /* Disable power to the USB bus */ - badge4_set_5V(BADGE4_5V_USB, 0); - } -#endif -} - - -/*-------------------------------------------------------------------------*/ - -#if 0 -static void dump_hci_status(struct usb_hcd *hcd, const char *label) -{ - unsigned long status = sa1111_readl(hcd->regs + SA1111_USB_STATUS); - - dbg ("%s USB_STATUS = { %s%s%s%s%s}", label, - ((status & USB_STATUS_IRQHCIRMTWKUP) ? "IRQHCIRMTWKUP " : ""), - ((status & USB_STATUS_IRQHCIBUFFACC) ? "IRQHCIBUFFACC " : ""), - ((status & USB_STATUS_NIRQHCIM) ? "" : "IRQHCIM "), - ((status & USB_STATUS_NHCIMFCLR) ? "" : "HCIMFCLR "), - ((status & USB_STATUS_USBPWRSENSE) ? "USBPWRSENSE " : "")); } -#endif - -/*-------------------------------------------------------------------------*/ - -/* configure so an HC device and id are always provided */ -/* always called with process context; sleeping is OK */ - /** - * usb_hcd_sa1111_probe - initialize SA-1111-based HCDs - * Context: !in_interrupt() + * ohci_hcd_sa1111_probe - initialize SA-1111-based HCDs * * Allocates basic resources for this USB host controller, and - * then invokes the start() method for the HCD associated with it - * through the hotplug entry's driver_data. - * - * Store this function in the HCD's struct pci_driver as probe(). + * then invokes the start() method for the HCD associated with it. */ -int usb_hcd_sa1111_probe (const struct hc_driver *driver, - struct sa1111_dev *dev) +static int ohci_hcd_sa1111_probe(struct sa1111_dev *dev) { struct usb_hcd *hcd; - int retval; + int ret; - hcd = usb_create_hcd (driver, &dev->dev, "sa1111"); + if (usb_disabled()) + return -ENODEV; + + hcd = usb_create_hcd(&ohci_sa1111_hc_driver, &dev->dev, "sa1111"); if (!hcd) return -ENOMEM; + hcd->rsrc_start = dev->res.start; hcd->rsrc_len = resource_size(&dev->res); if (!request_mem_region(hcd->rsrc_start, hcd->rsrc_len, hcd_name)) { dbg("request_mem_region failed"); - retval = -EBUSY; + ret = -EBUSY; goto err1; } + hcd->regs = dev->mapbase; - sa1111_start_hc(dev); - ohci_hcd_init(hcd_to_ohci(hcd)); + ret = sa1111_start_hc(dev); + if (ret) + goto err2; - retval = usb_add_hcd(hcd, dev->irq[1], 0); - if (retval == 0) - return retval; + ret = usb_add_hcd(hcd, dev->irq[1], 0); + if (ret == 0) + return ret; sa1111_stop_hc(dev); + err2: release_mem_region(hcd->rsrc_start, hcd->rsrc_len); err1: usb_put_hcd(hcd); - return retval; + return ret; } - -/* may be called without controller electrically present */ -/* may be called with controller, bus, and devices active */ - /** - * usb_hcd_sa1111_remove - shutdown processing for SA-1111-based HCDs + * ohci_hcd_sa1111_remove - shutdown processing for SA-1111-based HCDs * @dev: USB Host Controller being removed - * Context: !in_interrupt() - * - * Reverses the effect of usb_hcd_sa1111_probe(), first invoking - * the HCD's stop() method. It is always called from a thread - * context, normally "rmmod", "apmd", or something similar. * + * Reverses the effect of ohci_hcd_sa1111_probe(), first invoking + * the HCD's stop() method. */ -void usb_hcd_sa1111_remove (struct usb_hcd *hcd, struct sa1111_dev *dev) +static int ohci_hcd_sa1111_remove(struct sa1111_dev *dev) { + struct usb_hcd *hcd = sa1111_get_drvdata(dev); + usb_remove_hcd(hcd); sa1111_stop_hc(dev); release_mem_region(hcd->rsrc_start, hcd->rsrc_len); usb_put_hcd(hcd); -} - -/*-------------------------------------------------------------------------*/ -static int __devinit -ohci_sa1111_start (struct usb_hcd *hcd) -{ - struct ohci_hcd *ohci = hcd_to_ohci (hcd); - int ret; - - if ((ret = ohci_init(ohci)) < 0) - return ret; - - if ((ret = ohci_run (ohci)) < 0) { - err ("can't start %s", hcd->self.bus_name); - ohci_stop (hcd); - return ret; - } return 0; } -/*-------------------------------------------------------------------------*/ - -static const struct hc_driver ohci_sa1111_hc_driver = { - .description = hcd_name, - .product_desc = "SA-1111 OHCI", - .hcd_priv_size = sizeof(struct ohci_hcd), - - /* - * generic hardware linkage - */ - .irq = ohci_irq, - .flags = HCD_USB11 | HCD_MEMORY, - - /* - * basic lifecycle operations - */ - .start = ohci_sa1111_start, - .stop = ohci_stop, - - /* - * managing i/o requests and associated device resources - */ - .urb_enqueue = ohci_urb_enqueue, - .urb_dequeue = ohci_urb_dequeue, - .endpoint_disable = ohci_endpoint_disable, - - /* - * scheduling support - */ - .get_frame_number = ohci_get_frame, - - /* - * root hub support - */ - .hub_status_data = ohci_hub_status_data, - .hub_control = ohci_hub_control, -#ifdef CONFIG_PM - .bus_suspend = ohci_bus_suspend, - .bus_resume = ohci_bus_resume, -#endif - .start_port_reset = ohci_start_port_reset, -}; - -/*-------------------------------------------------------------------------*/ - -static int ohci_hcd_sa1111_drv_probe(struct sa1111_dev *dev) -{ - int ret; - - if (usb_disabled()) - return -ENODEV; - - ret = usb_hcd_sa1111_probe(&ohci_sa1111_hc_driver, dev); - return ret; -} - -static int ohci_hcd_sa1111_drv_remove(struct sa1111_dev *dev) +static void ohci_hcd_sa1111_shutdown(struct sa1111_dev *dev) { struct usb_hcd *hcd = sa1111_get_drvdata(dev); - usb_hcd_sa1111_remove(hcd, dev); - return 0; + if (test_bit(HCD_FLAG_HW_ACCESSIBLE, &hcd->flags)) { + hcd->driver->shutdown(hcd); + sa1111_stop_hc(dev); + } } static struct sa1111_driver ohci_hcd_sa1111_driver = { .drv = { .name = "sa1111-ohci", + .owner = THIS_MODULE, }, .devid = SA1111_DEVID_USB, - .probe = ohci_hcd_sa1111_drv_probe, - .remove = ohci_hcd_sa1111_drv_remove, + .probe = ohci_hcd_sa1111_probe, + .remove = ohci_hcd_sa1111_remove, + .shutdown = ohci_hcd_sa1111_shutdown, }; - diff --git a/drivers/usb/host/oxu210hp-hcd.c b/drivers/usb/host/oxu210hp-hcd.c index 015c7c62ed49..3b38030b02a8 100644 --- a/drivers/usb/host/oxu210hp-hcd.c +++ b/drivers/usb/host/oxu210hp-hcd.c @@ -40,7 +40,6 @@ #include <linux/io.h> #include <asm/irq.h> -#include <asm/system.h> #include <asm/unaligned.h> #include <linux/irq.h> diff --git a/drivers/usb/host/pci-quirks.c b/drivers/usb/host/pci-quirks.c index 7732d69e49e0..32dada8c8b4f 100644 --- a/drivers/usb/host/pci-quirks.c +++ b/drivers/usb/host/pci-quirks.c @@ -825,9 +825,13 @@ static void __devinit quirk_usb_handoff_xhci(struct pci_dev *pdev) } } - /* Disable any BIOS SMIs */ - writel(XHCI_LEGACY_DISABLE_SMI, - base + ext_cap_offset + XHCI_LEGACY_CONTROL_OFFSET); + val = readl(base + ext_cap_offset + XHCI_LEGACY_CONTROL_OFFSET); + /* Mask off (turn off) any enabled SMIs */ + val &= XHCI_LEGACY_DISABLE_SMI; + /* Mask all SMI events bits, RW1C */ + val |= XHCI_LEGACY_SMI_EVENTS; + /* Disable any BIOS SMIs and clear all SMI events*/ + writel(val, base + ext_cap_offset + XHCI_LEGACY_CONTROL_OFFSET); if (usb_is_intel_switchable_xhci(pdev)) usb_enable_xhci_ports(pdev); @@ -893,4 +897,5 @@ static void __devinit quirk_usb_early_handoff(struct pci_dev *pdev) quirk_usb_handoff_xhci(pdev); pci_disable_device(pdev); } -DECLARE_PCI_FIXUP_FINAL(PCI_ANY_ID, PCI_ANY_ID, quirk_usb_early_handoff); +DECLARE_PCI_FIXUP_CLASS_FINAL(PCI_ANY_ID, PCI_ANY_ID, + PCI_CLASS_SERIAL_USB, 8, quirk_usb_early_handoff); diff --git a/drivers/usb/host/sl811-hcd.c b/drivers/usb/host/sl811-hcd.c index 2a2cce2d2fa7..91ce1c02e617 100644 --- a/drivers/usb/host/sl811-hcd.c +++ b/drivers/usb/host/sl811-hcd.c @@ -51,7 +51,6 @@ #include <asm/io.h> #include <asm/irq.h> -#include <asm/system.h> #include <asm/byteorder.h> #include <asm/unaligned.h> diff --git a/drivers/usb/host/u132-hcd.c b/drivers/usb/host/u132-hcd.c index 16dd6a6abf00..dbbd1ba25224 100644 --- a/drivers/usb/host/u132-hcd.c +++ b/drivers/usb/host/u132-hcd.c @@ -55,7 +55,6 @@ #include <linux/mutex.h> #include <asm/io.h> #include <asm/irq.h> -#include <asm/system.h> #include <asm/byteorder.h> /* FIXME ohci.h is ONLY for internal use by the OHCI driver. diff --git a/drivers/usb/host/uhci-hcd.c b/drivers/usb/host/uhci-hcd.c index e37dea87bb56..e4db350602b8 100644 --- a/drivers/usb/host/uhci-hcd.c +++ b/drivers/usb/host/uhci-hcd.c @@ -45,7 +45,6 @@ #include <asm/uaccess.h> #include <asm/io.h> #include <asm/irq.h> -#include <asm/system.h> #include "uhci-hcd.h" diff --git a/drivers/usb/host/uhci-hub.c b/drivers/usb/host/uhci-hub.c index 045cde4cbc3d..768d54295a20 100644 --- a/drivers/usb/host/uhci-hub.c +++ b/drivers/usb/host/uhci-hub.c @@ -196,11 +196,12 @@ static int uhci_hub_status_data(struct usb_hcd *hcd, char *buf) status = get_hub_status_data(uhci, buf); switch (uhci->rh_state) { - case UHCI_RH_SUSPENDING: case UHCI_RH_SUSPENDED: /* if port change, ask to be resumed */ - if (status || uhci->resuming_ports) + if (status || uhci->resuming_ports) { + status = 1; usb_hcd_resume_root_hub(hcd); + } break; case UHCI_RH_AUTO_STOPPED: diff --git a/drivers/usb/host/xhci-dbg.c b/drivers/usb/host/xhci-dbg.c index e9b0f043455d..4b436f5a4171 100644 --- a/drivers/usb/host/xhci-dbg.c +++ b/drivers/usb/host/xhci-dbg.c @@ -119,7 +119,7 @@ static void xhci_print_command_reg(struct xhci_hcd *xhci) xhci_dbg(xhci, " Event Interrupts %s\n", (temp & CMD_EIE) ? "enabled " : "disabled"); xhci_dbg(xhci, " Host System Error Interrupts %s\n", - (temp & CMD_EIE) ? "enabled " : "disabled"); + (temp & CMD_HSEIE) ? "enabled " : "disabled"); xhci_dbg(xhci, " HC has %sfinished light reset\n", (temp & CMD_LRESET) ? "not " : ""); } diff --git a/drivers/usb/host/xhci-ext-caps.h b/drivers/usb/host/xhci-ext-caps.h index c7f33123d4c0..377f4242dabb 100644 --- a/drivers/usb/host/xhci-ext-caps.h +++ b/drivers/usb/host/xhci-ext-caps.h @@ -62,8 +62,9 @@ /* USB Legacy Support Control and Status Register - section 7.1.2 */ /* Add this offset, plus the value of xECP in HCCPARAMS to the base address */ #define XHCI_LEGACY_CONTROL_OFFSET (0x04) -/* bits 1:2, 5:12, and 17:19 need to be preserved; bits 21:28 should be zero */ -#define XHCI_LEGACY_DISABLE_SMI ((0x3 << 1) + (0xff << 5) + (0x7 << 17)) +/* bits 1:3, 5:12, and 17:19 need to be preserved; bits 21:28 should be zero */ +#define XHCI_LEGACY_DISABLE_SMI ((0x7 << 1) + (0xff << 5) + (0x7 << 17)) +#define XHCI_LEGACY_SMI_EVENTS (0x7 << 29) /* USB 2.0 xHCI 0.96 L1C capability - section 7.2.2.1.3.2 */ #define XHCI_L1C (1 << 16) diff --git a/drivers/usb/host/xhci-mem.c b/drivers/usb/host/xhci-mem.c index cae4c6f2845a..68eaa908ac8e 100644 --- a/drivers/usb/host/xhci-mem.c +++ b/drivers/usb/host/xhci-mem.c @@ -1796,11 +1796,6 @@ void xhci_mem_cleanup(struct xhci_hcd *xhci) int i; /* Free the Event Ring Segment Table and the actual Event Ring */ - if (xhci->ir_set) { - xhci_writel(xhci, 0, &xhci->ir_set->erst_size); - xhci_write_64(xhci, 0, &xhci->ir_set->erst_base); - xhci_write_64(xhci, 0, &xhci->ir_set->erst_dequeue); - } size = sizeof(struct xhci_erst_entry)*(xhci->erst.num_entries); if (xhci->erst.entries) dma_free_coherent(&pdev->dev, size, @@ -1812,7 +1807,6 @@ void xhci_mem_cleanup(struct xhci_hcd *xhci) xhci->event_ring = NULL; xhci_dbg(xhci, "Freed event ring\n"); - xhci_write_64(xhci, 0, &xhci->op_regs->cmd_ring); if (xhci->cmd_ring) xhci_ring_free(xhci, xhci->cmd_ring); xhci->cmd_ring = NULL; @@ -1841,7 +1835,6 @@ void xhci_mem_cleanup(struct xhci_hcd *xhci) xhci->medium_streams_pool = NULL; xhci_dbg(xhci, "Freed medium stream array pool\n"); - xhci_write_64(xhci, 0, &xhci->op_regs->dcbaa_ptr); if (xhci->dcbaa) dma_free_coherent(&pdev->dev, sizeof(*xhci->dcbaa), xhci->dcbaa, xhci->dcbaa->dma); @@ -2459,6 +2452,8 @@ int xhci_mem_init(struct xhci_hcd *xhci, gfp_t flags) fail: xhci_warn(xhci, "Couldn't initialize memory\n"); + xhci_halt(xhci); + xhci_reset(xhci); xhci_mem_cleanup(xhci); return -ENOMEM; } diff --git a/drivers/usb/host/xhci-pci.c b/drivers/usb/host/xhci-pci.c index ef98b38626fb..7a856a767e77 100644 --- a/drivers/usb/host/xhci-pci.c +++ b/drivers/usb/host/xhci-pci.c @@ -95,6 +95,8 @@ static void xhci_pci_quirks(struct device *dev, struct xhci_hcd *xhci) xhci->quirks |= XHCI_RESET_ON_RESUME; xhci_dbg(xhci, "QUIRK: Resetting on resume\n"); } + if (pdev->vendor == PCI_VENDOR_ID_VIA) + xhci->quirks |= XHCI_RESET_ON_RESUME; } /* called during probe() after chip reset completes */ @@ -326,7 +328,7 @@ int __init xhci_register_pci(void) return pci_register_driver(&xhci_pci_driver); } -void __exit xhci_unregister_pci(void) +void xhci_unregister_pci(void) { pci_unregister_driver(&xhci_pci_driver); } diff --git a/drivers/usb/host/xhci-ring.c b/drivers/usb/host/xhci-ring.c index 6bd9d53062eb..3d9422f16a20 100644 --- a/drivers/usb/host/xhci-ring.c +++ b/drivers/usb/host/xhci-ring.c @@ -2417,7 +2417,7 @@ hw_died: u32 irq_pending; /* Acknowledge the PCI interrupt */ irq_pending = xhci_readl(xhci, &xhci->ir_set->irq_pending); - irq_pending |= 0x3; + irq_pending |= IMAN_IP; xhci_writel(xhci, irq_pending, &xhci->ir_set->irq_pending); } @@ -2734,7 +2734,7 @@ int xhci_queue_intr_tx(struct xhci_hcd *xhci, gfp_t mem_flags, urb->dev->speed == USB_SPEED_FULL) urb->interval /= 8; } - return xhci_queue_bulk_tx(xhci, GFP_ATOMIC, urb, slot_id, ep_index); + return xhci_queue_bulk_tx(xhci, mem_flags, urb, slot_id, ep_index); } /* @@ -3514,7 +3514,7 @@ int xhci_queue_isoc_tx_prepare(struct xhci_hcd *xhci, gfp_t mem_flags, } ep_ring->num_trbs_free_temp = ep_ring->num_trbs_free; - return xhci_queue_isoc_tx(xhci, GFP_ATOMIC, urb, slot_id, ep_index); + return xhci_queue_isoc_tx(xhci, mem_flags, urb, slot_id, ep_index); } /**** Command Ring Operations ****/ diff --git a/drivers/usb/host/xhci.c b/drivers/usb/host/xhci.c index e1963d4a430f..36641a7f2371 100644 --- a/drivers/usb/host/xhci.c +++ b/drivers/usb/host/xhci.c @@ -106,6 +106,9 @@ int xhci_halt(struct xhci_hcd *xhci) STS_HALT, STS_HALT, XHCI_MAX_HALT_USEC); if (!ret) xhci->xhc_state |= XHCI_STATE_HALTED; + else + xhci_warn(xhci, "Host not halted after %u microseconds.\n", + XHCI_MAX_HALT_USEC); return ret; } @@ -664,11 +667,11 @@ static void xhci_save_registers(struct xhci_hcd *xhci) xhci->s3.dev_nt = xhci_readl(xhci, &xhci->op_regs->dev_notification); xhci->s3.dcbaa_ptr = xhci_read_64(xhci, &xhci->op_regs->dcbaa_ptr); xhci->s3.config_reg = xhci_readl(xhci, &xhci->op_regs->config_reg); - xhci->s3.irq_pending = xhci_readl(xhci, &xhci->ir_set->irq_pending); - xhci->s3.irq_control = xhci_readl(xhci, &xhci->ir_set->irq_control); xhci->s3.erst_size = xhci_readl(xhci, &xhci->ir_set->erst_size); xhci->s3.erst_base = xhci_read_64(xhci, &xhci->ir_set->erst_base); xhci->s3.erst_dequeue = xhci_read_64(xhci, &xhci->ir_set->erst_dequeue); + xhci->s3.irq_pending = xhci_readl(xhci, &xhci->ir_set->irq_pending); + xhci->s3.irq_control = xhci_readl(xhci, &xhci->ir_set->irq_control); } static void xhci_restore_registers(struct xhci_hcd *xhci) @@ -677,10 +680,11 @@ static void xhci_restore_registers(struct xhci_hcd *xhci) xhci_writel(xhci, xhci->s3.dev_nt, &xhci->op_regs->dev_notification); xhci_write_64(xhci, xhci->s3.dcbaa_ptr, &xhci->op_regs->dcbaa_ptr); xhci_writel(xhci, xhci->s3.config_reg, &xhci->op_regs->config_reg); - xhci_writel(xhci, xhci->s3.irq_pending, &xhci->ir_set->irq_pending); - xhci_writel(xhci, xhci->s3.irq_control, &xhci->ir_set->irq_control); xhci_writel(xhci, xhci->s3.erst_size, &xhci->ir_set->erst_size); xhci_write_64(xhci, xhci->s3.erst_base, &xhci->ir_set->erst_base); + xhci_write_64(xhci, xhci->s3.erst_dequeue, &xhci->ir_set->erst_dequeue); + xhci_writel(xhci, xhci->s3.irq_pending, &xhci->ir_set->irq_pending); + xhci_writel(xhci, xhci->s3.irq_control, &xhci->ir_set->irq_control); } static void xhci_set_cmd_ring_deq(struct xhci_hcd *xhci) diff --git a/drivers/usb/host/xhci.h b/drivers/usb/host/xhci.h index 91074fdab3eb..3d69c4b2b542 100644 --- a/drivers/usb/host/xhci.h +++ b/drivers/usb/host/xhci.h @@ -205,6 +205,10 @@ struct xhci_op_regs { #define CMD_PM_INDEX (1 << 11) /* bits 12:31 are reserved (and should be preserved on writes). */ +/* IMAN - Interrupt Management Register */ +#define IMAN_IP (1 << 1) +#define IMAN_IE (1 << 0) + /* USBSTS - USB status - status bitmasks */ /* HC not running - set to 1 when run/stop bit is cleared. */ #define STS_HALT XHCI_STS_HALT diff --git a/drivers/usb/musb/ux500_dma.c b/drivers/usb/musb/ux500_dma.c index 97cb45916c43..d05c7fbbb703 100644 --- a/drivers/usb/musb/ux500_dma.c +++ b/drivers/usb/musb/ux500_dma.c @@ -115,12 +115,12 @@ static bool ux500_configure_channel(struct dma_channel *channel, slave_conf.dst_addr = usb_fifo_addr; slave_conf.dst_addr_width = addr_width; slave_conf.dst_maxburst = 16; + slave_conf.device_fc = false; dma_chan->device->device_control(dma_chan, DMA_SLAVE_CONFIG, (unsigned long) &slave_conf); - dma_desc = dma_chan->device-> - device_prep_slave_sg(dma_chan, &sg, 1, direction, + dma_desc = dmaengine_prep_slave_sg(dma_chan, &sg, 1, direction, DMA_PREP_INTERRUPT | DMA_CTRL_ACK); if (!dma_desc) return false; diff --git a/drivers/usb/renesas_usbhs/fifo.c b/drivers/usb/renesas_usbhs/fifo.c index 3648c82a17fe..6ec7f838d7fa 100644 --- a/drivers/usb/renesas_usbhs/fifo.c +++ b/drivers/usb/renesas_usbhs/fifo.c @@ -786,9 +786,8 @@ static void xfer_work(struct work_struct *work) sg_dma_address(&sg) = pkt->dma + pkt->actual; sg_dma_len(&sg) = pkt->trans; - desc = chan->device->device_prep_slave_sg(chan, &sg, 1, dir, - DMA_PREP_INTERRUPT | - DMA_CTRL_ACK); + desc = dmaengine_prep_slave_sg(chan, &sg, 1, dir, + DMA_PREP_INTERRUPT | DMA_CTRL_ACK); if (!desc) return; diff --git a/drivers/usb/serial/bus.c b/drivers/usb/serial/bus.c index 7f547dc3a590..ed8adb052ca7 100644 --- a/drivers/usb/serial/bus.c +++ b/drivers/usb/serial/bus.c @@ -60,8 +60,6 @@ static int usb_serial_device_probe(struct device *dev) retval = -ENODEV; goto exit; } - if (port->dev_state != PORT_REGISTERING) - goto exit; driver = port->serial->type; if (driver->port_probe) { @@ -98,9 +96,6 @@ static int usb_serial_device_remove(struct device *dev) if (!port) return -ENODEV; - if (port->dev_state != PORT_UNREGISTERING) - return retval; - device_remove_file(&port->dev, &dev_attr_port_number); driver = port->serial->type; diff --git a/drivers/usb/serial/ftdi_sio.c b/drivers/usb/serial/ftdi_sio.c index 7c229d304684..02e7f2d32d52 100644 --- a/drivers/usb/serial/ftdi_sio.c +++ b/drivers/usb/serial/ftdi_sio.c @@ -75,7 +75,8 @@ struct ftdi_private { unsigned long last_dtr_rts; /* saved modem control outputs */ struct async_icount icount; wait_queue_head_t delta_msr_wait; /* Used for TIOCMIWAIT */ - char prev_status, diff_status; /* Used for TIOCMIWAIT */ + char prev_status; /* Used for TIOCMIWAIT */ + bool dev_gone; /* Used to abort TIOCMIWAIT */ char transmit_empty; /* If transmitter is empty or not */ struct usb_serial_port *port; __u16 interface; /* FT2232C, FT2232H or FT4232H port interface @@ -1681,6 +1682,7 @@ static int ftdi_sio_port_probe(struct usb_serial_port *port) init_waitqueue_head(&priv->delta_msr_wait); priv->flags = ASYNC_LOW_LATENCY; + priv->dev_gone = false; if (quirk && quirk->port_probe) quirk->port_probe(priv); @@ -1724,7 +1726,8 @@ static void ftdi_HE_TIRA1_setup(struct ftdi_private *priv) /* * Module parameter to control latency timer for NDI FTDI-based USB devices. - * If this value is not set in modprobe.conf.local its value will be set to 1ms. + * If this value is not set in /etc/modprobe.d/ its value will be set + * to 1ms. */ static int ndi_latency_timer = 1; @@ -1838,6 +1841,9 @@ static int ftdi_sio_port_remove(struct usb_serial_port *port) dbg("%s", __func__); + priv->dev_gone = true; + wake_up_interruptible_all(&priv->delta_msr_wait); + remove_sysfs_attrs(port); kref_put(&priv->kref, ftdi_sio_priv_release); @@ -1981,17 +1987,19 @@ static int ftdi_process_packet(struct tty_struct *tty, N.B. packet may be processed more than once, but differences are only processed once. */ status = packet[0] & FTDI_STATUS_B0_MASK; - if (status & FTDI_RS0_CTS) - priv->icount.cts++; - if (status & FTDI_RS0_DSR) - priv->icount.dsr++; - if (status & FTDI_RS0_RI) - priv->icount.rng++; - if (status & FTDI_RS0_RLSD) - priv->icount.dcd++; if (status != priv->prev_status) { - priv->diff_status |= status ^ priv->prev_status; - wake_up_interruptible(&priv->delta_msr_wait); + char diff_status = status ^ priv->prev_status; + + if (diff_status & FTDI_RS0_CTS) + priv->icount.cts++; + if (diff_status & FTDI_RS0_DSR) + priv->icount.dsr++; + if (diff_status & FTDI_RS0_RI) + priv->icount.rng++; + if (diff_status & FTDI_RS0_RLSD) + priv->icount.dcd++; + + wake_up_interruptible_all(&priv->delta_msr_wait); priv->prev_status = status; } @@ -2394,15 +2402,12 @@ static int ftdi_ioctl(struct tty_struct *tty, */ case TIOCMIWAIT: cprev = priv->icount; - while (1) { + while (!priv->dev_gone) { interruptible_sleep_on(&priv->delta_msr_wait); /* see if a signal did it */ if (signal_pending(current)) return -ERESTARTSYS; cnow = priv->icount; - if (cnow.rng == cprev.rng && cnow.dsr == cprev.dsr && - cnow.dcd == cprev.dcd && cnow.cts == cprev.cts) - return -EIO; /* no change => error */ if (((arg & TIOCM_RNG) && (cnow.rng != cprev.rng)) || ((arg & TIOCM_DSR) && (cnow.dsr != cprev.dsr)) || ((arg & TIOCM_CD) && (cnow.dcd != cprev.dcd)) || @@ -2411,7 +2416,7 @@ static int ftdi_ioctl(struct tty_struct *tty, } cprev = cnow; } - /* not reached */ + return -EIO; break; case TIOCSERGETLSR: return get_lsr_info(port, (struct serial_struct __user *)arg); diff --git a/drivers/usb/serial/metro-usb.c b/drivers/usb/serial/metro-usb.c index 6e1622f2a297..08d16e8c002d 100644 --- a/drivers/usb/serial/metro-usb.c +++ b/drivers/usb/serial/metro-usb.c @@ -27,8 +27,8 @@ /* Product information. */ #define FOCUS_VENDOR_ID 0x0C2E -#define FOCUS_PRODUCT_ID 0x0720 -#define FOCUS_PRODUCT_ID_UNI 0x0710 +#define FOCUS_PRODUCT_ID_BI 0x0720 +#define FOCUS_PRODUCT_ID_UNI 0x0700 #define METROUSB_SET_REQUEST_TYPE 0x40 #define METROUSB_SET_MODEM_CTRL_REQUEST 10 @@ -47,7 +47,7 @@ struct metrousb_private { /* Device table list. */ static struct usb_device_id id_table[] = { - { USB_DEVICE(FOCUS_VENDOR_ID, FOCUS_PRODUCT_ID) }, + { USB_DEVICE(FOCUS_VENDOR_ID, FOCUS_PRODUCT_ID_BI) }, { USB_DEVICE(FOCUS_VENDOR_ID, FOCUS_PRODUCT_ID_UNI) }, { }, /* Terminating entry. */ }; diff --git a/drivers/usb/serial/option.c b/drivers/usb/serial/option.c index 6815701cf656..f4465ccddc35 100644 --- a/drivers/usb/serial/option.c +++ b/drivers/usb/serial/option.c @@ -708,6 +708,7 @@ static const struct usb_device_id option_ids[] = { { USB_DEVICE(NOVATELWIRELESS_VENDOR_ID, NOVATELWIRELESS_PRODUCT_EVDO_EMBEDDED_FULLSPEED) }, { USB_DEVICE(NOVATELWIRELESS_VENDOR_ID, NOVATELWIRELESS_PRODUCT_HSPA_EMBEDDED_FULLSPEED) }, { USB_DEVICE(NOVATELWIRELESS_VENDOR_ID, NOVATELWIRELESS_PRODUCT_EVDO_HIGHSPEED) }, + { USB_DEVICE(NOVATELWIRELESS_VENDOR_ID, NOVATELWIRELESS_PRODUCT_HSPA_HIGHSPEED) }, { USB_DEVICE(NOVATELWIRELESS_VENDOR_ID, NOVATELWIRELESS_PRODUCT_HSPA_HIGHSPEED3) }, { USB_DEVICE(NOVATELWIRELESS_VENDOR_ID, NOVATELWIRELESS_PRODUCT_HSPA_HIGHSPEED4) }, { USB_DEVICE(NOVATELWIRELESS_VENDOR_ID, NOVATELWIRELESS_PRODUCT_HSPA_HIGHSPEED5) }, @@ -903,8 +904,10 @@ static const struct usb_device_id option_ids[] = { { USB_DEVICE_AND_INTERFACE_INFO(ZTE_VENDOR_ID, 0x0165, 0xff, 0xff, 0xff) }, { USB_DEVICE_AND_INTERFACE_INFO(ZTE_VENDOR_ID, 0x0167, 0xff, 0xff, 0xff), .driver_info = (kernel_ulong_t)&net_intf4_blacklist }, - { USB_DEVICE_AND_INTERFACE_INFO(ZTE_VENDOR_ID, 0x1008, 0xff, 0xff, 0xff) }, - { USB_DEVICE_AND_INTERFACE_INFO(ZTE_VENDOR_ID, 0x1010, 0xff, 0xff, 0xff) }, + { USB_DEVICE_AND_INTERFACE_INFO(ZTE_VENDOR_ID, 0x1008, 0xff, 0xff, 0xff), + .driver_info = (kernel_ulong_t)&net_intf4_blacklist }, + { USB_DEVICE_AND_INTERFACE_INFO(ZTE_VENDOR_ID, 0x1010, 0xff, 0xff, 0xff), + .driver_info = (kernel_ulong_t)&net_intf4_blacklist }, { USB_DEVICE_AND_INTERFACE_INFO(ZTE_VENDOR_ID, 0x1012, 0xff, 0xff, 0xff) }, { USB_DEVICE_AND_INTERFACE_INFO(ZTE_VENDOR_ID, 0x1057, 0xff, 0xff, 0xff) }, { USB_DEVICE_AND_INTERFACE_INFO(ZTE_VENDOR_ID, 0x1058, 0xff, 0xff, 0xff) }, diff --git a/drivers/usb/serial/pl2303.c b/drivers/usb/serial/pl2303.c index ff4a174fa5de..a1a9062954c4 100644 --- a/drivers/usb/serial/pl2303.c +++ b/drivers/usb/serial/pl2303.c @@ -420,7 +420,7 @@ static void pl2303_set_termios(struct tty_struct *tty, control = priv->line_control; if ((cflag & CBAUD) == B0) priv->line_control &= ~(CONTROL_DTR | CONTROL_RTS); - else + else if ((old_termios->c_cflag & CBAUD) == B0) priv->line_control |= (CONTROL_DTR | CONTROL_RTS); if (control != priv->line_control) { control = priv->line_control; diff --git a/drivers/usb/serial/sierra.c b/drivers/usb/serial/sierra.c index f14465a83dd1..fdd5aa2c8d82 100644 --- a/drivers/usb/serial/sierra.c +++ b/drivers/usb/serial/sierra.c @@ -289,6 +289,7 @@ static const struct usb_device_id id_table[] = { { USB_DEVICE(0x1199, 0x6856) }, /* Sierra Wireless AirCard 881 U */ { USB_DEVICE(0x1199, 0x6859) }, /* Sierra Wireless AirCard 885 E */ { USB_DEVICE(0x1199, 0x685A) }, /* Sierra Wireless AirCard 885 E */ + { USB_DEVICE(0x1199, 0x68A2) }, /* Sierra Wireless MC7710 */ /* Sierra Wireless C885 */ { USB_DEVICE_AND_INTERFACE_INFO(0x1199, 0x6880, 0xFF, 0xFF, 0xFF)}, /* Sierra Wireless C888, Air Card 501, USB 303, USB 304 */ diff --git a/drivers/usb/serial/usb-serial.c b/drivers/usb/serial/usb-serial.c index 69230f01056a..97355a15bbea 100644 --- a/drivers/usb/serial/usb-serial.c +++ b/drivers/usb/serial/usb-serial.c @@ -1059,6 +1059,12 @@ int usb_serial_probe(struct usb_interface *interface, serial->attached = 1; } + /* Avoid race with tty_open and serial_install by setting the + * disconnected flag and not clearing it until all ports have been + * registered. + */ + serial->disconnected = 1; + if (get_free_serial(serial, num_ports, &minor) == NULL) { dev_err(&interface->dev, "No more free serial devices\n"); goto probe_error; @@ -1070,19 +1076,16 @@ int usb_serial_probe(struct usb_interface *interface, port = serial->port[i]; dev_set_name(&port->dev, "ttyUSB%d", port->number); dbg ("%s - registering %s", __func__, dev_name(&port->dev)); - port->dev_state = PORT_REGISTERING; device_enable_async_suspend(&port->dev); retval = device_add(&port->dev); - if (retval) { + if (retval) dev_err(&port->dev, "Error registering port device, " "continuing\n"); - port->dev_state = PORT_UNREGISTERED; - } else { - port->dev_state = PORT_REGISTERED; - } } + serial->disconnected = 0; + usb_serial_console_init(debug, minor); exit: @@ -1124,22 +1127,8 @@ void usb_serial_disconnect(struct usb_interface *interface) } kill_traffic(port); cancel_work_sync(&port->work); - if (port->dev_state == PORT_REGISTERED) { - - /* Make sure the port is bound so that the - * driver's port_remove method is called. - */ - if (!port->dev.driver) { - int rc; - - port->dev.driver = - &serial->type->driver; - rc = device_bind_driver(&port->dev); - } - port->dev_state = PORT_UNREGISTERING; + if (device_is_registered(&port->dev)) device_del(&port->dev); - port->dev_state = PORT_UNREGISTERED; - } } } serial->type->disconnect(serial); diff --git a/drivers/usb/storage/Kconfig b/drivers/usb/storage/Kconfig index fe2d803a6347..7691c866637b 100644 --- a/drivers/usb/storage/Kconfig +++ b/drivers/usb/storage/Kconfig @@ -222,7 +222,7 @@ config USB_LIBUSUAL for usb-storage and ub drivers, and allows to switch binding of these devices without rebuilding modules. - Typical syntax of /etc/modprobe.conf is: + Typical syntax of /etc/modprobe.d/*conf is: options libusual bias="ub" diff --git a/drivers/usb/storage/usb.c b/drivers/usb/storage/usb.c index c18538e4a6db..2653e73db623 100644 --- a/drivers/usb/storage/usb.c +++ b/drivers/usb/storage/usb.c @@ -132,6 +132,35 @@ static struct us_unusual_dev for_dynamic_ids = #undef COMPLIANT_DEV #undef USUAL_DEV +#ifdef CONFIG_LOCKDEP + +static struct lock_class_key us_interface_key[USB_MAXINTERFACES]; + +static void us_set_lock_class(struct mutex *mutex, + struct usb_interface *intf) +{ + struct usb_device *udev = interface_to_usbdev(intf); + struct usb_host_config *config = udev->actconfig; + int i; + + for (i = 0; i < config->desc.bNumInterfaces; i++) { + if (config->interface[i] == intf) + break; + } + + BUG_ON(i == config->desc.bNumInterfaces); + + lockdep_set_class(mutex, &us_interface_key[i]); +} + +#else + +static void us_set_lock_class(struct mutex *mutex, + struct usb_interface *intf) +{ +} + +#endif #ifdef CONFIG_PM /* Minimal support for suspend and resume */ @@ -895,6 +924,7 @@ int usb_stor_probe1(struct us_data **pus, *pus = us = host_to_us(host); memset(us, 0, sizeof(struct us_data)); mutex_init(&(us->dev_mutex)); + us_set_lock_class(&us->dev_mutex, intf); init_completion(&us->cmnd_ready); init_completion(&(us->notify)); init_waitqueue_head(&us->delay_wait); |