2 files changed, 291 insertions, 24 deletions

diff --git a/drivers/tty/serial/msm_serial.c b/drivers/tty/serial/msm_serial.c
index 2315a614ff45..7006d979d9d2 100644
--- a/drivers/tty/serial/msm_serial.c
+++ b/drivers/tty/serial/msm_serial.c
@@ -20,6 +20,8 @@
 #endif
 
 #include <linux/atomic.h>
+#include <linux/dma-mapping.h>
+#include <linux/dmaengine.h>
 #include <linux/hrtimer.h>
 #include <linux/module.h>
 #include <linux/io.h>
@@ -39,6 +41,10 @@
 
 #include "msm_serial.h"
 
+#define UARTDM_BURST_SIZE	16   /* in bytes */
+#define UARTDM_TX_AIGN(x)	((x) & ~0x3) /* valid for > 1p3 */
+#define UARTDM_TX_MAX		256   /* in bytes, valid for <= 1p3 */
+
 enum {
 	UARTDM_1P1 = 1,
 	UARTDM_1P2,
@@ -46,6 +52,17 @@ enum {
 	UARTDM_1P4,
 };
 
+struct msm_dma {
+	struct dma_chan		*chan;
+	enum dma_data_direction dir;
+	dma_addr_t		phys;
+	unsigned char		*virt;
+	dma_cookie_t		cookie;
+	u32			enable_bit;
+	unsigned int		count;
+	struct dma_async_tx_descriptor	*desc;
+};
+
 struct msm_port {
 	struct uart_port	uart;
 	char			name[16];
@@ -55,8 +72,93 @@ struct msm_port {
 	int			is_uartdm;
 	unsigned int		old_snap_state;
 	bool			break_detected;
+	struct msm_dma		tx_dma;
 };
 
+static void msm_handle_tx(struct uart_port *port);
+
+void msm_stop_dma(struct uart_port *port, struct msm_dma *dma)
+{
+	struct device *dev = port->dev;
+	unsigned int mapped;
+	u32 val;
+
+	mapped = dma->count;
+	dma->count = 0;
+
+	dmaengine_terminate_all(dma->chan);
+
+	/*
+	 * DMA Stall happens if enqueue and flush command happens concurrently.
+	 * For example before changing the baud rate/protocol configuration and
+	 * sending flush command to ADM, disable the channel of UARTDM.
+	 * Note: should not reset the receiver here immediately as it is not
+	 * suggested to do disable/reset or reset/disable at the same time.
+	 */
+	val = msm_read(port, UARTDM_DMEN);
+	val &= ~dma->enable_bit;
+	msm_write(port, val, UARTDM_DMEN);
+
+	if (mapped)
+		dma_unmap_single(dev, dma->phys, mapped, dma->dir);
+}
+
+static void msm_release_dma(struct msm_port *msm_port)
+{
+	struct msm_dma *dma;
+
+	dma = &msm_port->tx_dma;
+	if (dma->chan) {
+		msm_stop_dma(&msm_port->uart, dma);
+		dma_release_channel(dma->chan);
+	}
+
+	memset(dma, 0, sizeof(*dma));
+}
+
+static void msm_request_tx_dma(struct msm_port *msm_port, resource_size_t base)
+{
+	struct device *dev = msm_port->uart.dev;
+	struct dma_slave_config conf;
+	struct msm_dma *dma;
+	u32 crci = 0;
+	int ret;
+
+	dma = &msm_port->tx_dma;
+
+	/* allocate DMA resources, if available */
+	dma->chan = dma_request_slave_channel_reason(dev, "tx");
+	if (IS_ERR(dma->chan))
+		goto no_tx;
+
+	of_property_read_u32(dev->of_node, "qcom,tx-crci", &crci);
+
+	memset(&conf, 0, sizeof(conf));
+	conf.direction = DMA_MEM_TO_DEV;
+	conf.device_fc = true;
+	conf.dst_addr = base + UARTDM_TF;
+	conf.dst_maxburst = UARTDM_BURST_SIZE;
+	conf.slave_id = crci;
+
+	ret = dmaengine_slave_config(dma->chan, &conf);
+	if (ret)
+		goto rel_tx;
+
+	dma->dir = DMA_TO_DEVICE;
+
+	if (msm_port->is_uartdm < UARTDM_1P4)
+		dma->enable_bit = UARTDM_DMEN_TX_DM_ENABLE;
+	else
+		dma->enable_bit = UARTDM_DMEN_TX_BAM_ENABLE;
+
+	return;
+
+rel_tx:
+	dma_release_channel(dma->chan);
+no_tx:
+	memset(dma, 0, sizeof(*dma));
+}
+
 static inline void msm_wait_for_xmitr(struct uart_port *port)
 {
 	while (!(msm_read(port, UART_SR) & UART_SR_TX_EMPTY)) {
@@ -78,11 +180,132 @@ static void msm_stop_tx(struct uart_port *port)
 static void msm_start_tx(struct uart_port *port)
 {
 	struct msm_port *msm_port = UART_TO_MSM(port);
+	struct msm_dma *dma = &msm_port->tx_dma;
+
+	/* Already started in DMA mode */
+	if (dma->count)
+		return;
+
+	msm_port->imr |= UART_IMR_TXLEV;
+	msm_write(port, msm_port->imr, UART_IMR);
+}
+
+static void msm_reset_dm_count(struct uart_port *port, int count)
+{
+	msm_wait_for_xmitr(port);
+	msm_write(port, count, UARTDM_NCF_TX);
+	msm_read(port, UARTDM_NCF_TX);
+}
+
+static void msm_complete_tx_dma(void *args)
+{
+	struct msm_port *msm_port = args;
+	struct uart_port *port = &msm_port->uart;
+	struct circ_buf *xmit = &port->state->xmit;
+	struct msm_dma *dma = &msm_port->tx_dma;
+	struct dma_tx_state state;
+	enum dma_status status;
+	unsigned long flags;
+	unsigned int count;
+	u32 val;
+
+	spin_lock_irqsave(&port->lock, flags);
+
+	/* Already stopped */
+	if (!dma->count)
+		goto done;
+
+	status = dmaengine_tx_status(dma->chan, dma->cookie, &state);
 
+	dma_unmap_single(port->dev, dma->phys, dma->count, dma->dir);
+
+	val = msm_read(port, UARTDM_DMEN);
+	val &= ~dma->enable_bit;
+	msm_write(port, val, UARTDM_DMEN);
+
+	if (msm_port->is_uartdm > UARTDM_1P3) {
+		msm_write(port, UART_CR_CMD_RESET_TX, UART_CR);
+		msm_write(port, UART_CR_TX_ENABLE, UART_CR);
+	}
+
+	count = dma->count - state.residue;
+	port->icount.tx += count;
+	dma->count = 0;
+
+	xmit->tail += count;
+	xmit->tail &= UART_XMIT_SIZE - 1;
+
+	/* Restore "Tx FIFO below watermark" interrupt */
 	msm_port->imr |= UART_IMR_TXLEV;
 	msm_write(port, msm_port->imr, UART_IMR);
+
+	if (uart_circ_chars_pending(xmit) < WAKEUP_CHARS)
+		uart_write_wakeup(port);
+
+	msm_handle_tx(port);
+done:
+	spin_unlock_irqrestore(&port->lock, flags);
 }
 
+static int msm_handle_tx_dma(struct msm_port *msm_port, unsigned int count)
+{
+	struct circ_buf *xmit = &msm_port->uart.state->xmit;
+	struct uart_port *port = &msm_port->uart;
+	struct msm_dma *dma = &msm_port->tx_dma;
+	void *cpu_addr;
+	int ret;
+	u32 val;
+
+	cpu_addr = &xmit->buf[xmit->tail];
+
+	dma->phys = dma_map_single(port->dev, cpu_addr, count, dma->dir);
+	ret = dma_mapping_error(port->dev, dma->phys);
+	if (ret)
+		return ret;
+
+	dma->desc = dmaengine_prep_slave_single(dma->chan, dma->phys,
+						count, DMA_MEM_TO_DEV,
+						DMA_PREP_INTERRUPT |
+						DMA_PREP_FENCE);
+	if (!dma->desc) {
+		ret = -EIO;
+		goto unmap;
+	}
+
+	dma->desc->callback = msm_complete_tx_dma;
+	dma->desc->callback_param = msm_port;
+
+	dma->cookie = dmaengine_submit(dma->desc);
+	ret = dma_submit_error(dma->cookie);
+	if (ret)
+		goto unmap;
+
+	/*
+	 * Using DMA complete for Tx FIFO reload, no need for
+	 * "Tx FIFO below watermark" one, disable it
+	 */
+	msm_port->imr &= ~UART_IMR_TXLEV;
+	msm_write(port, msm_port->imr, UART_IMR);
+
+	dma->count = count;
+
+	val = msm_read(port, UARTDM_DMEN);
+	val |= dma->enable_bit;
+
+	if (msm_port->is_uartdm < UARTDM_1P4)
+		msm_write(port, val, UARTDM_DMEN);
+
+	msm_reset_dm_count(port, count);
+
+	if (msm_port->is_uartdm > UARTDM_1P3)
+		msm_write(port, val, UARTDM_DMEN);
+
+	dma_async_issue_pending(dma->chan);
+	return 0;
+unmap:
+	dma_unmap_single(port->dev, dma->phys, count, dma->dir);
+	return ret;
+}
 static void msm_stop_rx(struct uart_port *port)
 {
 	struct msm_port *msm_port = UART_TO_MSM(port);
@@ -224,18 +447,11 @@ static void msm_handle_rx(struct uart_port *port)
 	spin_lock(&port->lock);
 }
 
-static void msm_reset_dm_count(struct uart_port *port, int count)
-{
-	msm_wait_for_xmitr(port);
-	msm_write(port, count, UARTDM_NCF_TX);
-	msm_read(port, UARTDM_NCF_TX);
-}
-
-static void msm_handle_tx(struct uart_port *port)
+static void msm_handle_tx_pio(struct uart_port *port, unsigned int tx_count)
 {
 	struct circ_buf *xmit = &port->state->xmit;
 	struct msm_port *msm_port = UART_TO_MSM(port);
-	unsigned int tx_count, num_chars;
+	unsigned int num_chars;
 	unsigned int tf_pointer = 0;
 	void __iomem *tf;
 
@@ -244,20 +460,8 @@ static void msm_handle_tx(struct uart_port *port)
 	else
 		tf = port->membase + UART_TF;
 
-	tx_count = uart_circ_chars_pending(xmit);
-	tx_count = min3(tx_count, (unsigned int)UART_XMIT_SIZE - xmit->tail,
-			port->fifosize);
-
-	if (port->x_char) {
-		if (msm_port->is_uartdm)
-			msm_reset_dm_count(port, tx_count + 1);
-
-		iowrite8_rep(tf, &port->x_char, 1);
-		port->icount.tx++;
-		port->x_char = 0;
-	} else if (tx_count && msm_port->is_uartdm) {
+	if (tx_count && msm_port->is_uartdm)
 		msm_reset_dm_count(port, tx_count);
-	}
 
 	while (tf_pointer < tx_count) {
 		int i;
@@ -290,6 +494,59 @@ static void msm_handle_tx(struct uart_port *port)
 		uart_write_wakeup(port);
 }
 
+static void msm_handle_tx(struct uart_port *port)
+{
+	struct msm_port *msm_port = UART_TO_MSM(port);
+	struct circ_buf *xmit = &msm_port->uart.state->xmit;
+	struct msm_dma *dma = &msm_port->tx_dma;
+	unsigned int pio_count, dma_count, dma_min;
+	void __iomem *tf;
+	int err = 0;
+
+	if (port->x_char) {
+		if (msm_port->is_uartdm)
+			tf = port->membase + UARTDM_TF;
+		else
+			tf = port->membase + UART_TF;
+
+		if (msm_port->is_uartdm)
+			msm_reset_dm_count(port, 1);
+
+		iowrite8_rep(tf, &port->x_char, 1);
+		port->icount.tx++;
+		port->x_char = 0;
+		return;
+	}
+
+	if (uart_circ_empty(xmit) || uart_tx_stopped(port)) {
+		msm_stop_tx(port);
+		return;
+	}
+
+	pio_count = CIRC_CNT(xmit->head, xmit->tail, UART_XMIT_SIZE);
+	dma_count = CIRC_CNT_TO_END(xmit->head, xmit->tail, UART_XMIT_SIZE);
+
+	dma_min = 1;	/* Always DMA */
+	if (msm_port->is_uartdm > UARTDM_1P3) {
+		dma_count = UARTDM_TX_AIGN(dma_count);
+		dma_min = UARTDM_BURST_SIZE;
+	} else {
+		if (dma_count > UARTDM_TX_MAX)
+			dma_count = UARTDM_TX_MAX;
+	}
+
+	if (pio_count > port->fifosize)
+		pio_count = port->fifosize;
+
+	if (!dma->chan || dma_count < dma_min)
+		msm_handle_tx_pio(port, pio_count);
+	else
+		err = msm_handle_tx_dma(msm_port, dma_count);
+
+	if (err)	/* fall back to PIO mode */
+		msm_handle_tx_pio(port, pio_count);
+}
+
 static void msm_handle_delta_cts(struct uart_port *port)
 {
 	msm_write(port, UART_CR_CMD_RESET_CTS, UART_CR);
@@ -301,9 +558,10 @@ static irqreturn_t msm_uart_irq(int irq, void *dev_id)
 {
 	struct uart_port *port = dev_id;
 	struct msm_port *msm_port = UART_TO_MSM(port);
+	unsigned long flags;
 	unsigned int misr;
 
-	spin_lock(&port->lock);
+	spin_lock_irqsave(&port->lock, flags);
 	misr = msm_read(port, UART_MISR);
 	msm_write(port, 0, UART_IMR); /* disable interrupt */
 
@@ -324,7 +582,7 @@ static irqreturn_t msm_uart_irq(int irq, void *dev_id)
 		msm_handle_delta_cts(port);
 
 	msm_write(port, msm_port->imr, UART_IMR); /* restore interrupt */
-	spin_unlock(&port->lock);
+	spin_unlock_irqrestore(&port->lock, flags);
 
 	return IRQ_HANDLED;
 }
@@ -515,6 +773,9 @@ static int msm_startup(struct uart_port *port)
 	data |= UART_MR1_AUTO_RFR_LEVEL0 & rfr_level;
 	msm_write(port, data, UART_MR1);
 
+	if (msm_port->is_uartdm)
+		msm_request_tx_dma(msm_port, msm_port->uart.mapbase);
+
 	return 0;
 }
 
@@ -525,6 +786,9 @@ static void msm_shutdown(struct uart_port *port)
 	msm_port->imr = 0;
 	msm_write(port, 0, UART_IMR); /* disable interrupts */
 
+	if (msm_port->is_uartdm)
+		msm_release_dma(msm_port);
+
 	clk_disable_unprepare(msm_port->clk);
 
 	free_irq(port->irq, port);
diff --git a/drivers/tty/serial/msm_serial.h b/drivers/tty/serial/msm_serial.h
index 60917d30c6b5..103ae61b9d06 100644
--- a/drivers/tty/serial/msm_serial.h
+++ b/drivers/tty/serial/msm_serial.h
@@ -121,6 +121,9 @@
 #define UARTDM_DMEN_RX_SC_ENABLE BIT(5)
 #define UARTDM_DMEN_TX_SC_ENABLE BIT(4)
 
+#define UARTDM_DMEN_TX_BAM_ENABLE BIT(2)	/* UARTDM_1P4 */
+#define UARTDM_DMEN_TX_DM_ENABLE  BIT(0)	/* < UARTDM_1P4 */
+
 #define UARTDM_DMRX		0x34
 #define UARTDM_NCF_TX		0x40
 #define UARTDM_RX_TOTAL_SNAP	0x38