diff options
Diffstat (limited to 'drivers/power/supply/ab8500-bm.h')
| -rw-r--r-- | drivers/power/supply/ab8500-bm.h | 278 |
1 files changed, 274 insertions, 4 deletions
diff --git a/drivers/power/supply/ab8500-bm.h b/drivers/power/supply/ab8500-bm.h index a1b31c971a45..41c69a4f2a1f 100644 --- a/drivers/power/supply/ab8500-bm.h +++ b/drivers/power/supply/ab8500-bm.h @@ -4,7 +4,6 @@ #define _AB8500_CHARGER_H_ #include <linux/kernel.h> -#include <linux/mfd/abx500.h> /* * System control 2 register offsets. @@ -268,6 +267,277 @@ enum bup_vch_sel { #define BUS_PP_PRECHG_CURRENT_MASK 0x0E #define BUS_POWER_PATH_PRECHG_ENA 0x01 +/* + * ADC for the battery thermistor. + * When using the ABx500_ADC_THERM_BATCTRL the battery ID resistor is combined + * with a NTC resistor to both identify the battery and to measure its + * temperature. Different phone manufactures uses different techniques to both + * identify the battery and to read its temperature. + */ +enum abx500_adc_therm { + ABx500_ADC_THERM_BATCTRL, + ABx500_ADC_THERM_BATTEMP, +}; + +/** + * struct abx500_res_to_temp - defines one point in a temp to res curve. To + * be used in battery packs that combines the identification resistor with a + * NTC resistor. + * @temp: battery pack temperature in Celsius + * @resist: NTC resistor net total resistance + */ +struct abx500_res_to_temp { + int temp; + int resist; +}; + +/** + * struct abx500_v_to_cap - Table for translating voltage to capacity + * @voltage: Voltage in mV + * @capacity: Capacity in percent + */ +struct abx500_v_to_cap { + int voltage; + int capacity; +}; + +/* Forward declaration */ +struct abx500_fg; + +/** + * struct abx500_fg_parameters - Fuel gauge algorithm parameters, in seconds + * if not specified + * @recovery_sleep_timer: Time between measurements while recovering + * @recovery_total_time: Total recovery time + * @init_timer: Measurement interval during startup + * @init_discard_time: Time we discard voltage measurement at startup + * @init_total_time: Total init time during startup + * @high_curr_time: Time current has to be high to go to recovery + * @accu_charging: FG accumulation time while charging + * @accu_high_curr: FG accumulation time in high current mode + * @high_curr_threshold: High current threshold, in mA + * @lowbat_threshold: Low battery threshold, in mV + * @overbat_threshold: Over battery threshold, in mV + * @battok_falling_th_sel0 Threshold in mV for battOk signal sel0 + * Resolution in 50 mV step. + * @battok_raising_th_sel1 Threshold in mV for battOk signal sel1 + * Resolution in 50 mV step. + * @user_cap_limit Capacity reported from user must be within this + * limit to be considered as sane, in percentage + * points. + * @maint_thres This is the threshold where we stop reporting + * battery full while in maintenance, in per cent + * @pcut_enable: Enable power cut feature in ab8505 + * @pcut_max_time: Max time threshold + * @pcut_flag_time: Flagtime threshold + * @pcut_max_restart: Max number of restarts + * @pcut_debounce_time: Sets battery debounce time + */ +struct abx500_fg_parameters { + int recovery_sleep_timer; + int recovery_total_time; + int init_timer; + int init_discard_time; + int init_total_time; + int high_curr_time; + int accu_charging; + int accu_high_curr; + int high_curr_threshold; + int lowbat_threshold; + int overbat_threshold; + int battok_falling_th_sel0; + int battok_raising_th_sel1; + int user_cap_limit; + int maint_thres; + bool pcut_enable; + u8 pcut_max_time; + u8 pcut_flag_time; + u8 pcut_max_restart; + u8 pcut_debounce_time; +}; + +/** + * struct abx500_charger_maximization - struct used by the board config. + * @use_maxi: Enable maximization for this battery type + * @maxi_chg_curr: Maximum charger current allowed + * @maxi_wait_cycles: cycles to wait before setting charger current + * @charger_curr_step delta between two charger current settings (mA) + */ +struct abx500_maxim_parameters { + bool ena_maxi; + int chg_curr; + int wait_cycles; + int charger_curr_step; +}; + +/** + * struct abx500_battery_type - different batteries supported + * @name: battery technology + * @resis_high: battery upper resistance limit + * @resis_low: battery lower resistance limit + * @charge_full_design: Maximum battery capacity in mAh + * @nominal_voltage: Nominal voltage of the battery in mV + * @termination_vol: max voltage upto which battery can be charged + * @termination_curr battery charging termination current in mA + * @recharge_cap battery capacity limit that will trigger a new + * full charging cycle in the case where maintenan- + * -ce charging has been disabled + * @normal_cur_lvl: charger current in normal state in mA + * @normal_vol_lvl: charger voltage in normal state in mV + * @maint_a_cur_lvl: charger current in maintenance A state in mA + * @maint_a_vol_lvl: charger voltage in maintenance A state in mV + * @maint_a_chg_timer_h: charge time in maintenance A state + * @maint_b_cur_lvl: charger current in maintenance B state in mA + * @maint_b_vol_lvl: charger voltage in maintenance B state in mV + * @maint_b_chg_timer_h: charge time in maintenance B state + * @low_high_cur_lvl: charger current in temp low/high state in mA + * @low_high_vol_lvl: charger voltage in temp low/high state in mV' + * @battery_resistance: battery inner resistance in mOhm. + * @n_r_t_tbl_elements: number of elements in r_to_t_tbl + * @r_to_t_tbl: table containing resistance to temp points + * @n_v_cap_tbl_elements: number of elements in v_to_cap_tbl + * @v_to_cap_tbl: Voltage to capacity (in %) table + * @n_batres_tbl_elements number of elements in the batres_tbl + * @batres_tbl battery internal resistance vs temperature table + */ +struct abx500_battery_type { + int name; + int resis_high; + int resis_low; + int charge_full_design; + int nominal_voltage; + int termination_vol; + int termination_curr; + int recharge_cap; + int normal_cur_lvl; + int normal_vol_lvl; + int maint_a_cur_lvl; + int maint_a_vol_lvl; + int maint_a_chg_timer_h; + int maint_b_cur_lvl; + int maint_b_vol_lvl; + int maint_b_chg_timer_h; + int low_high_cur_lvl; + int low_high_vol_lvl; + int battery_resistance; + int n_temp_tbl_elements; + const struct abx500_res_to_temp *r_to_t_tbl; + int n_v_cap_tbl_elements; + const struct abx500_v_to_cap *v_to_cap_tbl; + int n_batres_tbl_elements; + const struct batres_vs_temp *batres_tbl; +}; + +/** + * struct abx500_bm_capacity_levels - abx500 capacity level data + * @critical: critical capacity level in percent + * @low: low capacity level in percent + * @normal: normal capacity level in percent + * @high: high capacity level in percent + * @full: full capacity level in percent + */ +struct abx500_bm_capacity_levels { + int critical; + int low; + int normal; + int high; + int full; +}; + +/** + * struct abx500_bm_charger_parameters - Charger specific parameters + * @usb_volt_max: maximum allowed USB charger voltage in mV + * @usb_curr_max: maximum allowed USB charger current in mA + * @ac_volt_max: maximum allowed AC charger voltage in mV + * @ac_curr_max: maximum allowed AC charger current in mA + */ +struct abx500_bm_charger_parameters { + int usb_volt_max; + int usb_curr_max; + int ac_volt_max; + int ac_curr_max; +}; + +/** + * struct abx500_bm_data - abx500 battery management data + * @temp_under under this temp, charging is stopped + * @temp_low between this temp and temp_under charging is reduced + * @temp_high between this temp and temp_over charging is reduced + * @temp_over over this temp, charging is stopped + * @temp_now present battery temperature + * @temp_interval_chg temperature measurement interval in s when charging + * @temp_interval_nochg temperature measurement interval in s when not charging + * @main_safety_tmr_h safety timer for main charger + * @usb_safety_tmr_h safety timer for usb charger + * @bkup_bat_v voltage which we charge the backup battery with + * @bkup_bat_i current which we charge the backup battery with + * @no_maintenance indicates that maintenance charging is disabled + * @capacity_scaling indicates whether capacity scaling is to be used + * @abx500_adc_therm placement of thermistor, batctrl or battemp adc + * @chg_unknown_bat flag to enable charging of unknown batteries + * @enable_overshoot flag to enable VBAT overshoot control + * @auto_trig flag to enable auto adc trigger + * @fg_res resistance of FG resistor in 0.1mOhm + * @n_btypes number of elements in array bat_type + * @batt_id index of the identified battery in array bat_type + * @interval_charging charge alg cycle period time when charging (sec) + * @interval_not_charging charge alg cycle period time when not charging (sec) + * @temp_hysteresis temperature hysteresis + * @gnd_lift_resistance Battery ground to phone ground resistance (mOhm) + * @n_chg_out_curr number of elements in array chg_output_curr + * @n_chg_in_curr number of elements in array chg_input_curr + * @chg_output_curr charger output current level map + * @chg_input_curr charger input current level map + * @maxi maximization parameters + * @cap_levels capacity in percent for the different capacity levels + * @bat_type table of supported battery types + * @chg_params charger parameters + * @fg_params fuel gauge parameters + */ +struct abx500_bm_data { + int temp_under; + int temp_low; + int temp_high; + int temp_over; + int temp_now; + int temp_interval_chg; + int temp_interval_nochg; + int main_safety_tmr_h; + int usb_safety_tmr_h; + int bkup_bat_v; + int bkup_bat_i; + bool autopower_cfg; + bool ac_enabled; + bool usb_enabled; + bool no_maintenance; + bool capacity_scaling; + bool chg_unknown_bat; + bool enable_overshoot; + bool auto_trig; + enum abx500_adc_therm adc_therm; + int fg_res; + int n_btypes; + int batt_id; + int interval_charging; + int interval_not_charging; + int temp_hysteresis; + int gnd_lift_resistance; + int n_chg_out_curr; + int n_chg_in_curr; + int *chg_output_curr; + int *chg_input_curr; + const struct abx500_maxim_parameters *maxi; + const struct abx500_bm_capacity_levels *cap_levels; + struct abx500_battery_type *bat_type; + const struct abx500_bm_charger_parameters *chg_params; + const struct abx500_fg_parameters *fg_params; +}; + +enum { + NTC_EXTERNAL = 0, + NTC_INTERNAL, +}; + /** * struct res_to_temp - defines one point in a temp to res curve. To * be used in battery packs that combines the identification resistor with a @@ -447,9 +717,6 @@ struct ab8500_bm_data { const struct ab8500_fg_parameters *fg_params; }; -struct ab8500_btemp; -struct ab8500_fg; - extern struct abx500_bm_data ab8500_bm_data; void ab8500_charger_usb_state_changed(u8 bm_usb_state, u16 mA); @@ -459,5 +726,8 @@ int ab8500_fg_inst_curr_start(struct ab8500_fg *di); int ab8500_fg_inst_curr_finalize(struct ab8500_fg *di, int *res); int ab8500_fg_inst_curr_started(struct ab8500_fg *di); int ab8500_fg_inst_curr_done(struct ab8500_fg *di); +int ab8500_bm_of_probe(struct device *dev, + struct device_node *np, + struct abx500_bm_data *bm); #endif /* _AB8500_CHARGER_H_ */ |