diff options
Diffstat (limited to 'drivers/pinctrl/pinctrl-coh901.c')
| -rw-r--r-- | drivers/pinctrl/pinctrl-coh901.c | 220 |
1 files changed, 43 insertions, 177 deletions
diff --git a/drivers/pinctrl/pinctrl-coh901.c b/drivers/pinctrl/pinctrl-coh901.c index cc0f00d73d15..b446c9641212 100644 --- a/drivers/pinctrl/pinctrl-coh901.c +++ b/drivers/pinctrl/pinctrl-coh901.c @@ -1,11 +1,8 @@ /* * U300 GPIO module. * - * Copyright (C) 2007-2011 ST-Ericsson AB + * Copyright (C) 2007-2012 ST-Ericsson AB * License terms: GNU General Public License (GPL) version 2 - * This can driver either of the two basic GPIO cores - * available in the U300 platforms: - * COH 901 335 - Used in DB3150 (U300 1.0) and DB3200 (U330 1.0) * COH 901 571/3 - Used in DB3210 (U365 2.0) and DB3350 (U335 1.0) * Author: Linus Walleij <linus.walleij@linaro.org> * Author: Jonas Aaberg <jonas.aberg@stericsson.com> @@ -24,19 +21,22 @@ #include <linux/slab.h> #include <linux/pinctrl/consumer.h> #include <linux/pinctrl/pinconf-generic.h> -#include <mach/gpio-u300.h> +#include <linux/platform_data/pinctrl-coh901.h> #include "pinctrl-coh901.h" +#define U300_GPIO_PORT_STRIDE (0x30) /* - * Register definitions for COH 901 335 variant + * Control Register 32bit (R/W) + * bit 15-9 (mask 0x0000FE00) contains the number of cores. 8*cores + * gives the number of GPIO pins. + * bit 8-2 (mask 0x000001FC) contains the core version ID. */ -#define U300_335_PORT_STRIDE (0x1C) -/* Port X Pin Data Register 32bit, this is both input and output (R/W) */ -#define U300_335_PXPDIR (0x00) -#define U300_335_PXPDOR (0x00) -/* Port X Pin Config Register 32bit (R/W) */ -#define U300_335_PXPCR (0x04) -/* This register layout is the same in both blocks */ +#define U300_GPIO_CR (0x00) +#define U300_GPIO_CR_SYNC_SEL_ENABLE (0x00000002UL) +#define U300_GPIO_CR_BLOCK_CLKRQ_ENABLE (0x00000001UL) +#define U300_GPIO_PXPDIR (0x04) +#define U300_GPIO_PXPDOR (0x08) +#define U300_GPIO_PXPCR (0x0C) #define U300_GPIO_PXPCR_ALL_PINS_MODE_MASK (0x0000FFFFUL) #define U300_GPIO_PXPCR_PIN_MODE_MASK (0x00000003UL) #define U300_GPIO_PXPCR_PIN_MODE_SHIFT (0x00000002UL) @@ -44,53 +44,17 @@ #define U300_GPIO_PXPCR_PIN_MODE_OUTPUT_PUSH_PULL (0x00000001UL) #define U300_GPIO_PXPCR_PIN_MODE_OUTPUT_OPEN_DRAIN (0x00000002UL) #define U300_GPIO_PXPCR_PIN_MODE_OUTPUT_OPEN_SOURCE (0x00000003UL) -/* Port X Interrupt Event Register 32bit (R/W) */ -#define U300_335_PXIEV (0x08) -/* Port X Interrupt Enable Register 32bit (R/W) */ -#define U300_335_PXIEN (0x0C) -/* Port X Interrupt Force Register 32bit (R/W) */ -#define U300_335_PXIFR (0x10) -/* Port X Interrupt Config Register 32bit (R/W) */ -#define U300_335_PXICR (0x14) -/* This register layout is the same in both blocks */ +#define U300_GPIO_PXPER (0x10) +#define U300_GPIO_PXPER_ALL_PULL_UP_DISABLE_MASK (0x000000FFUL) +#define U300_GPIO_PXPER_PULL_UP_DISABLE (0x00000001UL) +#define U300_GPIO_PXIEV (0x14) +#define U300_GPIO_PXIEN (0x18) +#define U300_GPIO_PXIFR (0x1C) +#define U300_GPIO_PXICR (0x20) #define U300_GPIO_PXICR_ALL_IRQ_CONFIG_MASK (0x000000FFUL) #define U300_GPIO_PXICR_IRQ_CONFIG_MASK (0x00000001UL) #define U300_GPIO_PXICR_IRQ_CONFIG_FALLING_EDGE (0x00000000UL) #define U300_GPIO_PXICR_IRQ_CONFIG_RISING_EDGE (0x00000001UL) -/* Port X Pull-up Enable Register 32bit (R/W) */ -#define U300_335_PXPER (0x18) -/* This register layout is the same in both blocks */ -#define U300_GPIO_PXPER_ALL_PULL_UP_DISABLE_MASK (0x000000FFUL) -#define U300_GPIO_PXPER_PULL_UP_DISABLE (0x00000001UL) -/* Control Register 32bit (R/W) */ -#define U300_335_CR (0x54) -#define U300_335_CR_BLOCK_CLOCK_ENABLE (0x00000001UL) - -/* - * Register definitions for COH 901 571 / 3 variant - */ -#define U300_571_PORT_STRIDE (0x30) -/* - * Control Register 32bit (R/W) - * bit 15-9 (mask 0x0000FE00) contains the number of cores. 8*cores - * gives the number of GPIO pins. - * bit 8-2 (mask 0x000001FC) contains the core version ID. - */ -#define U300_571_CR (0x00) -#define U300_571_CR_SYNC_SEL_ENABLE (0x00000002UL) -#define U300_571_CR_BLOCK_CLKRQ_ENABLE (0x00000001UL) -/* - * These registers have the same layout and function as the corresponding - * COH 901 335 registers, just at different offset. - */ -#define U300_571_PXPDIR (0x04) -#define U300_571_PXPDOR (0x08) -#define U300_571_PXPCR (0x0C) -#define U300_571_PXPER (0x10) -#define U300_571_PXIEV (0x14) -#define U300_571_PXIEN (0x18) -#define U300_571_PXIFR (0x1C) -#define U300_571_PXICR (0x20) /* 8 bits per port, no version has more than 7 ports */ #define U300_GPIO_PINS_PER_PORT 8 @@ -149,8 +113,6 @@ struct u300_gpio_confdata { /* BS335 has seven ports of 8 bits each = GPIO pins 0..55 */ #define BS335_GPIO_NUM_PORTS 7 -/* BS365 has five ports of 8 bits each = GPIO pins 0..39 */ -#define BS365_GPIO_NUM_PORTS 5 #define U300_FLOATING_INPUT { \ .bias_mode = PIN_CONFIG_BIAS_HIGH_IMPEDANCE, \ @@ -172,7 +134,6 @@ struct u300_gpio_confdata { .outval = 1, \ } - /* Initial configuration */ static const struct __initconst u300_gpio_confdata bs335_gpio_config[BS335_GPIO_NUM_PORTS][U300_GPIO_PINS_PER_PORT] = { @@ -255,66 +216,6 @@ bs335_gpio_config[BS335_GPIO_NUM_PORTS][U300_GPIO_PINS_PER_PORT] = { } }; -static const struct __initconst u300_gpio_confdata -bs365_gpio_config[BS365_GPIO_NUM_PORTS][U300_GPIO_PINS_PER_PORT] = { - /* Port 0, pins 0-7 */ - { - U300_FLOATING_INPUT, - U300_OUTPUT_LOW, - U300_FLOATING_INPUT, - U300_OUTPUT_LOW, - U300_OUTPUT_LOW, - U300_OUTPUT_LOW, - U300_PULL_UP_INPUT, - U300_FLOATING_INPUT, - }, - /* Port 1, pins 0-7 */ - { - U300_OUTPUT_LOW, - U300_FLOATING_INPUT, - U300_OUTPUT_LOW, - U300_FLOATING_INPUT, - U300_FLOATING_INPUT, - U300_OUTPUT_HIGH, - U300_OUTPUT_LOW, - U300_OUTPUT_LOW, - }, - /* Port 2, pins 0-7 */ - { - U300_FLOATING_INPUT, - U300_PULL_UP_INPUT, - U300_OUTPUT_LOW, - U300_OUTPUT_LOW, - U300_PULL_UP_INPUT, - U300_PULL_UP_INPUT, - U300_PULL_UP_INPUT, - U300_PULL_UP_INPUT, - }, - /* Port 3, pins 0-7 */ - { - U300_PULL_UP_INPUT, - U300_PULL_UP_INPUT, - U300_PULL_UP_INPUT, - U300_PULL_UP_INPUT, - U300_PULL_UP_INPUT, - U300_PULL_UP_INPUT, - U300_PULL_UP_INPUT, - U300_PULL_UP_INPUT, - }, - /* Port 4, pins 0-7 */ - { - U300_PULL_UP_INPUT, - U300_PULL_UP_INPUT, - U300_PULL_UP_INPUT, - U300_PULL_UP_INPUT, - /* These 4 pins doesn't exist on DB3210 */ - U300_OUTPUT_LOW, - U300_OUTPUT_LOW, - U300_OUTPUT_LOW, - U300_OUTPUT_LOW, - } -}; - /** * to_u300_gpio() - get the pointer to u300_gpio * @chip: the gpio chip member of the structure u300_gpio @@ -716,13 +617,7 @@ static void __init u300_gpio_init_coh901571(struct u300_gpio *gpio, const struct u300_gpio_confdata *conf; int offset = (i*8) + j; - if (plat->variant == U300_GPIO_COH901571_3_BS335) - conf = &bs335_gpio_config[i][j]; - else if (plat->variant == U300_GPIO_COH901571_3_BS365) - conf = &bs365_gpio_config[i][j]; - else - break; - + conf = &bs335_gpio_config[i][j]; u300_gpio_init_pin(gpio, offset, conf); } } @@ -796,50 +691,27 @@ static int __init u300_gpio_probe(struct platform_device *pdev) goto err_no_ioremap; } - if (plat->variant == U300_GPIO_COH901335) { - dev_info(gpio->dev, - "initializing GPIO Controller COH 901 335\n"); - gpio->stride = U300_335_PORT_STRIDE; - gpio->pcr = U300_335_PXPCR; - gpio->dor = U300_335_PXPDOR; - gpio->dir = U300_335_PXPDIR; - gpio->per = U300_335_PXPER; - gpio->icr = U300_335_PXICR; - gpio->ien = U300_335_PXIEN; - gpio->iev = U300_335_PXIEV; - ifr = U300_335_PXIFR; - - /* Turn on the GPIO block */ - writel(U300_335_CR_BLOCK_CLOCK_ENABLE, - gpio->base + U300_335_CR); - } else if (plat->variant == U300_GPIO_COH901571_3_BS335 || - plat->variant == U300_GPIO_COH901571_3_BS365) { - dev_info(gpio->dev, - "initializing GPIO Controller COH 901 571/3\n"); - gpio->stride = U300_571_PORT_STRIDE; - gpio->pcr = U300_571_PXPCR; - gpio->dor = U300_571_PXPDOR; - gpio->dir = U300_571_PXPDIR; - gpio->per = U300_571_PXPER; - gpio->icr = U300_571_PXICR; - gpio->ien = U300_571_PXIEN; - gpio->iev = U300_571_PXIEV; - ifr = U300_571_PXIFR; - - val = readl(gpio->base + U300_571_CR); - dev_info(gpio->dev, "COH901571/3 block version: %d, " \ - "number of cores: %d totalling %d pins\n", - ((val & 0x000001FC) >> 2), - ((val & 0x0000FE00) >> 9), - ((val & 0x0000FE00) >> 9) * 8); - writel(U300_571_CR_BLOCK_CLKRQ_ENABLE, - gpio->base + U300_571_CR); - u300_gpio_init_coh901571(gpio, plat); - } else { - dev_err(gpio->dev, "unknown block variant\n"); - err = -ENODEV; - goto err_unknown_variant; - } + dev_info(gpio->dev, + "initializing GPIO Controller COH 901 571/3\n"); + gpio->stride = U300_GPIO_PORT_STRIDE; + gpio->pcr = U300_GPIO_PXPCR; + gpio->dor = U300_GPIO_PXPDOR; + gpio->dir = U300_GPIO_PXPDIR; + gpio->per = U300_GPIO_PXPER; + gpio->icr = U300_GPIO_PXICR; + gpio->ien = U300_GPIO_PXIEN; + gpio->iev = U300_GPIO_PXIEV; + ifr = U300_GPIO_PXIFR; + + val = readl(gpio->base + U300_GPIO_CR); + dev_info(gpio->dev, "COH901571/3 block version: %d, " \ + "number of cores: %d totalling %d pins\n", + ((val & 0x000001FC) >> 2), + ((val & 0x0000FE00) >> 9), + ((val & 0x0000FE00) >> 9) * 8); + writel(U300_GPIO_CR_BLOCK_CLKRQ_ENABLE, + gpio->base + U300_GPIO_CR); + u300_gpio_init_coh901571(gpio, plat); /* Add each port with its IRQ separately */ INIT_LIST_HEAD(&gpio->port_list); @@ -906,7 +778,6 @@ err_no_pinctrl: err_no_chip: err_no_port: u300_gpio_free_ports(gpio); -err_unknown_variant: iounmap(gpio->base); err_no_ioremap: release_mem_region(gpio->memres->start, resource_size(gpio->memres)); @@ -923,16 +794,11 @@ err_no_clk: static int __exit u300_gpio_remove(struct platform_device *pdev) { - struct u300_gpio_platform *plat = dev_get_platdata(&pdev->dev); struct u300_gpio *gpio = platform_get_drvdata(pdev); int err; /* Turn off the GPIO block */ - if (plat->variant == U300_GPIO_COH901335) - writel(0x00000000U, gpio->base + U300_335_CR); - if (plat->variant == U300_GPIO_COH901571_3_BS335 || - plat->variant == U300_GPIO_COH901571_3_BS365) - writel(0x00000000U, gpio->base + U300_571_CR); + writel(0x00000000U, gpio->base + U300_GPIO_CR); err = gpiochip_remove(&gpio->chip); if (err < 0) { |