diff options
Diffstat (limited to 'drivers/net/wireless/intel/iwlwifi/iwl-config.h')
| -rw-r--r-- | drivers/net/wireless/intel/iwlwifi/iwl-config.h | 53 |
1 files changed, 36 insertions, 17 deletions
diff --git a/drivers/net/wireless/intel/iwlwifi/iwl-config.h b/drivers/net/wireless/intel/iwlwifi/iwl-config.h index 1c1bf1b281cd..214495a7165f 100644 --- a/drivers/net/wireless/intel/iwlwifi/iwl-config.h +++ b/drivers/net/wireless/intel/iwlwifi/iwl-config.h @@ -161,7 +161,8 @@ static inline u8 num_of_ant(u8 mask) !!((mask) & ANT_C); } -/* +/** + * struct iwl_base_params - params not likely to change within a device family * @max_ll_items: max number of OTP blocks * @shadow_ram_support: shadow support for OTP memory * @led_compensation: compensate on the led on/off time per HW according @@ -331,7 +332,36 @@ struct iwl_csr_params { }; /** + * struct iwl_cfg_trans - information needed to start the trans + * + * These values cannot be changed when multiple configs are used for a + * single PCI ID, because they are needed before the HW REV or RFID + * can be read. + * + * @base_params: pointer to basic parameters + * @csr: csr flags and addresses that are different across devices + * @device_family: the device family + * @umac_prph_offset: offset to add to UMAC periphery address + * @rf_id: need to read rf_id to determine the firmware image + * @use_tfh: use TFH + * @gen2: 22000 and on transport operation + * @mq_rx_supported: multi-queue rx support + */ +struct iwl_cfg_trans_params { + const struct iwl_base_params *base_params; + const struct iwl_csr_params *csr; + enum iwl_device_family device_family; + u32 umac_prph_offset; + u32 rf_id:1, + use_tfh:1, + gen2:1, + mq_rx_supported:1, + bisr_workaround:1; +}; + +/** * struct iwl_cfg + * @trans: the trans-specific configuration part * @name: Official name of the device * @fw_name_pre: Firmware filename prefix. The api version and extension * (.ucode) will be added to filename before loading from disk. The @@ -346,10 +376,10 @@ struct iwl_csr_params { * @nvm_ver: NVM version * @nvm_calib_ver: NVM calibration version * @lib: pointer to the lib ops - * @base_params: pointer to basic parameters * @ht_params: point to ht parameters * @led_mode: 0=blinking, 1=On(RF On)/Off(RF Off) * @rx_with_siso_diversity: 1x1 device with rx antenna diversity + * @tx_with_siso_diversity: 1x1 device with tx antenna diversity * @internal_wimax_coex: internal wifi/wimax combo device * @high_temp: Is this NIC is designated to be in high temperature. * @host_interrupt_operation_mode: device needs host interrupt operation @@ -358,7 +388,6 @@ struct iwl_csr_params { * @mac_addr_from_csr: read HW address from CSR registers * @features: hw features, any combination of feature_whitelist * @pwr_tx_backoffs: translation table between power limits and backoffs - * @csr: csr flags and addresses that are different across devices * @max_rx_agg_size: max RX aggregation size of the ADDBA request/response * @max_tx_agg_size: max TX aggregation size of the ADDBA request/response * @max_ht_ampdu_factor: the exponent of the max length of A-MPDU that the @@ -371,18 +400,14 @@ struct iwl_csr_params { * @dccm2_len: length of the second DCCM * @smem_offset: offset from which the SMEM begins * @smem_len: the length of SMEM - * @mq_rx_supported: multi-queue rx support * @vht_mu_mimo_supported: VHT MU-MIMO support - * @rf_id: need to read rf_id to determine the firmware image * @integrated: discrete or integrated - * @gen2: 22000 and on transport operation * @cdb: CDB support * @nvm_type: see &enum iwl_nvm_type * @d3_debug_data_base_addr: base address where D3 debug data is stored * @d3_debug_data_length: length of the D3 debug data * @bisr_workaround: BISR hardware workaround (for 22260 series devices) * @min_txq_size: minimum number of slots required in a TX queue - * @umac_prph_offset: offset to add to UMAC periphery address * @uhb_supported: ultra high band channels supported * @min_256_ba_txq_size: minimum number of slots required in a TX queue which * supports 256 BA aggregation @@ -392,19 +417,16 @@ struct iwl_csr_params { * and/or the uCode API version instead. */ struct iwl_cfg { + struct iwl_cfg_trans_params trans; /* params specific to an individual device within a device family */ const char *name; const char *fw_name_pre; - /* params not likely to change within a device family */ - const struct iwl_base_params *base_params; /* params likely to change within a device family */ const struct iwl_ht_params *ht_params; const struct iwl_eeprom_params *eeprom_params; const struct iwl_pwr_tx_backoff *pwr_tx_backoffs; const char *default_nvm_file_C_step; const struct iwl_tt_params *thermal_params; - const struct iwl_csr_params *csr; - enum iwl_device_family device_family; enum iwl_led_mode led_mode; enum iwl_nvm_type nvm_type; u32 max_data_size; @@ -420,6 +442,7 @@ struct iwl_cfg { u16 nvm_ver; u16 nvm_calib_ver; u32 rx_with_siso_diversity:1, + tx_with_siso_diversity:1, bt_shared_single_ant:1, internal_wimax_coex:1, host_interrupt_operation_mode:1, @@ -428,15 +451,10 @@ struct iwl_cfg { lp_xtal_workaround:1, disable_dummy_notification:1, apmg_not_supported:1, - mq_rx_supported:1, vht_mu_mimo_supported:1, - rf_id:1, integrated:1, - use_tfh:1, - gen2:1, cdb:1, dbgc_supported:1, - bisr_workaround:1, uhb_supported:1; u8 valid_tx_ant; u8 valid_rx_ant; @@ -453,7 +471,6 @@ struct iwl_cfg { u32 d3_debug_data_base_addr; u32 d3_debug_data_length; u32 min_txq_size; - u32 umac_prph_offset; u32 fw_mon_smem_write_ptr_addr; u32 fw_mon_smem_write_ptr_msk; u32 fw_mon_smem_cycle_cnt_ptr_addr; @@ -577,6 +594,8 @@ extern const struct iwl_cfg iwl_ax1650i_cfg_quz_hr; extern const struct iwl_cfg iwl_ax1650s_cfg_quz_hr; extern const struct iwl_cfg killer1650s_2ax_cfg_qu_b0_hr_b0; extern const struct iwl_cfg killer1650i_2ax_cfg_qu_b0_hr_b0; +extern const struct iwl_cfg killer1650s_2ax_cfg_qu_c0_hr_b0; +extern const struct iwl_cfg killer1650i_2ax_cfg_qu_c0_hr_b0; extern const struct iwl_cfg killer1650x_2ax_cfg; extern const struct iwl_cfg killer1650w_2ax_cfg; extern const struct iwl_cfg iwl9461_2ac_cfg_qu_b0_jf_b0; |