diff options
Diffstat (limited to 'drivers/net/sky2.h')
-rw-r--r-- | drivers/net/sky2.h | 191 |
1 files changed, 149 insertions, 42 deletions
diff --git a/drivers/net/sky2.h b/drivers/net/sky2.h index 5efb5afc45ba..dce4d276d443 100644 --- a/drivers/net/sky2.h +++ b/drivers/net/sky2.h @@ -14,6 +14,8 @@ enum { PCI_DEV_REG3 = 0x80, PCI_DEV_REG4 = 0x84, PCI_DEV_REG5 = 0x88, + PCI_CFG_REG_0 = 0x90, + PCI_CFG_REG_1 = 0x94, }; enum { @@ -28,6 +30,7 @@ enum { enum pci_dev_reg_1 { PCI_Y2_PIG_ENA = 1<<31, /* Enable Plug-in-Go (YUKON-2) */ PCI_Y2_DLL_DIS = 1<<30, /* Disable PCI DLL (YUKON-2) */ + PCI_SW_PWR_ON_RST= 1<<30, /* SW Power on Reset (Yukon-EX) */ PCI_Y2_PHY2_COMA = 1<<29, /* Set PHY 2 to Coma Mode (YUKON-2) */ PCI_Y2_PHY1_COMA = 1<<28, /* Set PHY 1 to Coma Mode (YUKON-2) */ PCI_Y2_PHY2_POWD = 1<<27, /* Set PHY 2 to Power Down (YUKON-2) */ @@ -67,6 +70,80 @@ enum pci_dev_reg_4 { | P_ASPM_CLKRUN_REQUEST | P_ASPM_INT_FIFO_EMPTY, }; +/* PCI_OUR_REG_5 32 bit Our Register 5 (Yukon-ECU only) */ +enum pci_dev_reg_5 { + /* Bit 31..27: for A3 & later */ + P_CTL_DIV_CORE_CLK_ENA = 1<<31, /* Divide Core Clock Enable */ + P_CTL_SRESET_VMAIN_AV = 1<<30, /* Soft Reset for Vmain_av De-Glitch */ + P_CTL_BYPASS_VMAIN_AV = 1<<29, /* Bypass En. for Vmain_av De-Glitch */ + P_CTL_TIM_VMAIN_AV_MSK = 3<<27, /* Bit 28..27: Timer Vmain_av Mask */ + /* Bit 26..16: Release Clock on Event */ + P_REL_PCIE_RST_DE_ASS = 1<<26, /* PCIe Reset De-Asserted */ + P_REL_GPHY_REC_PACKET = 1<<25, /* GPHY Received Packet */ + P_REL_INT_FIFO_N_EMPTY = 1<<24, /* Internal FIFO Not Empty */ + P_REL_MAIN_PWR_AVAIL = 1<<23, /* Main Power Available */ + P_REL_CLKRUN_REQ_REL = 1<<22, /* CLKRUN Request Release */ + P_REL_PCIE_RESET_ASS = 1<<21, /* PCIe Reset Asserted */ + P_REL_PME_ASSERTED = 1<<20, /* PME Asserted */ + P_REL_PCIE_EXIT_L1_ST = 1<<19, /* PCIe Exit L1 State */ + P_REL_LOADER_NOT_FIN = 1<<18, /* EPROM Loader Not Finished */ + P_REL_PCIE_RX_EX_IDLE = 1<<17, /* PCIe Rx Exit Electrical Idle State */ + P_REL_GPHY_LINK_UP = 1<<16, /* GPHY Link Up */ + + /* Bit 10.. 0: Mask for Gate Clock */ + P_GAT_PCIE_RST_ASSERTED = 1<<10,/* PCIe Reset Asserted */ + P_GAT_GPHY_N_REC_PACKET = 1<<9, /* GPHY Not Received Packet */ + P_GAT_INT_FIFO_EMPTY = 1<<8, /* Internal FIFO Empty */ + P_GAT_MAIN_PWR_N_AVAIL = 1<<7, /* Main Power Not Available */ + P_GAT_CLKRUN_REQ_REL = 1<<6, /* CLKRUN Not Requested */ + P_GAT_PCIE_RESET_ASS = 1<<5, /* PCIe Reset Asserted */ + P_GAT_PME_DE_ASSERTED = 1<<4, /* PME De-Asserted */ + P_GAT_PCIE_ENTER_L1_ST = 1<<3, /* PCIe Enter L1 State */ + P_GAT_LOADER_FINISHED = 1<<2, /* EPROM Loader Finished */ + P_GAT_PCIE_RX_EL_IDLE = 1<<1, /* PCIe Rx Electrical Idle State */ + P_GAT_GPHY_LINK_DOWN = 1<<0, /* GPHY Link Down */ + + PCIE_OUR5_EVENT_CLK_D3_SET = P_REL_GPHY_REC_PACKET | + P_REL_INT_FIFO_N_EMPTY | + P_REL_PCIE_EXIT_L1_ST | + P_REL_PCIE_RX_EX_IDLE | + P_GAT_GPHY_N_REC_PACKET | + P_GAT_INT_FIFO_EMPTY | + P_GAT_PCIE_ENTER_L1_ST | + P_GAT_PCIE_RX_EL_IDLE, +}; + +#/* PCI_CFG_REG_1 32 bit Config Register 1 (Yukon-Ext only) */ +enum pci_cfg_reg1 { + P_CF1_DIS_REL_EVT_RST = 1<<24, /* Dis. Rel. Event during PCIE reset */ + /* Bit 23..21: Release Clock on Event */ + P_CF1_REL_LDR_NOT_FIN = 1<<23, /* EEPROM Loader Not Finished */ + P_CF1_REL_VMAIN_AVLBL = 1<<22, /* Vmain available */ + P_CF1_REL_PCIE_RESET = 1<<21, /* PCI-E reset */ + /* Bit 20..18: Gate Clock on Event */ + P_CF1_GAT_LDR_NOT_FIN = 1<<20, /* EEPROM Loader Finished */ + P_CF1_GAT_PCIE_RX_IDLE = 1<<19, /* PCI-E Rx Electrical idle */ + P_CF1_GAT_PCIE_RESET = 1<<18, /* PCI-E Reset */ + P_CF1_PRST_PHY_CLKREQ = 1<<17, /* Enable PCI-E rst & PM2PHY gen. CLKREQ */ + P_CF1_PCIE_RST_CLKREQ = 1<<16, /* Enable PCI-E rst generate CLKREQ */ + + P_CF1_ENA_CFG_LDR_DONE = 1<<8, /* Enable core level Config loader done */ + + P_CF1_ENA_TXBMU_RD_IDLE = 1<<1, /* Enable TX BMU Read IDLE for ASPM */ + P_CF1_ENA_TXBMU_WR_IDLE = 1<<0, /* Enable TX BMU Write IDLE for ASPM */ + + PCIE_CFG1_EVENT_CLK_D3_SET = P_CF1_DIS_REL_EVT_RST | + P_CF1_REL_LDR_NOT_FIN | + P_CF1_REL_VMAIN_AVLBL | + P_CF1_REL_PCIE_RESET | + P_CF1_GAT_LDR_NOT_FIN | + P_CF1_GAT_PCIE_RESET | + P_CF1_PRST_PHY_CLKREQ | + P_CF1_ENA_CFG_LDR_DONE | + P_CF1_ENA_TXBMU_RD_IDLE | + P_CF1_ENA_TXBMU_WR_IDLE, +}; + #define PCI_STATUS_ERROR_BITS (PCI_STATUS_DETECTED_PARITY | \ PCI_STATUS_SIG_SYSTEM_ERROR | \ @@ -364,6 +441,20 @@ enum { TST_CFG_WRITE_OFF= 1<<0, /* Disable Config Reg WR */ }; +/* B2_GPIO */ +enum { + GLB_GPIO_CLK_DEB_ENA = 1<<31, /* Clock Debug Enable */ + GLB_GPIO_CLK_DBG_MSK = 0xf<<26, /* Clock Debug */ + + GLB_GPIO_INT_RST_D3_DIS = 1<<15, /* Disable Internal Reset After D3 to D0 */ + GLB_GPIO_LED_PAD_SPEED_UP = 1<<14, /* LED PAD Speed Up */ + GLB_GPIO_STAT_RACE_DIS = 1<<13, /* Status Race Disable */ + GLB_GPIO_TEST_SEL_MSK = 3<<11, /* Testmode Select */ + GLB_GPIO_TEST_SEL_BASE = 1<<11, + GLB_GPIO_RAND_ENA = 1<<10, /* Random Enable */ + GLB_GPIO_RAND_BIT_1 = 1<<9, /* Random Bit 1 */ +}; + /* B2_MAC_CFG 8 bit MAC Configuration / Chip Revision */ enum { CFG_CHIP_R_MSK = 0xf<<4, /* Bit 7.. 4: Chip Revision */ @@ -392,6 +483,11 @@ enum { CHIP_REV_YU_FE_A2 = 2, }; +enum yukon_ex_rev { + CHIP_REV_YU_EX_A0 = 1, + CHIP_REV_YU_EX_B0 = 2, +}; + /* B2_Y2_CLK_GATE 8 bit Clock Gating (Yukon-2 only) */ enum { @@ -515,23 +611,15 @@ enum { enum { B8_Q_REGS = 0x0400, /* base of Queue registers */ Q_D = 0x00, /* 8*32 bit Current Descriptor */ - Q_DA_L = 0x20, /* 32 bit Current Descriptor Address Low dWord */ - Q_DA_H = 0x24, /* 32 bit Current Descriptor Address High dWord */ + Q_VLAN = 0x20, /* 16 bit Current VLAN Tag */ + Q_DONE = 0x24, /* 16 bit Done Index */ Q_AC_L = 0x28, /* 32 bit Current Address Counter Low dWord */ Q_AC_H = 0x2c, /* 32 bit Current Address Counter High dWord */ Q_BC = 0x30, /* 32 bit Current Byte Counter */ Q_CSR = 0x34, /* 32 bit BMU Control/Status Register */ - Q_F = 0x38, /* 32 bit Flag Register */ - Q_T1 = 0x3c, /* 32 bit Test Register 1 */ - Q_T1_TR = 0x3c, /* 8 bit Test Register 1 Transfer SM */ - Q_T1_WR = 0x3d, /* 8 bit Test Register 1 Write Descriptor SM */ - Q_T1_RD = 0x3e, /* 8 bit Test Register 1 Read Descriptor SM */ - Q_T1_SV = 0x3f, /* 8 bit Test Register 1 Supervisor SM */ - Q_T2 = 0x40, /* 32 bit Test Register 2 */ - Q_T3 = 0x44, /* 32 bit Test Register 3 */ + Q_TEST = 0x38, /* 32 bit Test/Control Register */ /* Yukon-2 */ - Q_DONE = 0x24, /* 16 bit Done Index (Yukon-2 only) */ Q_WM = 0x40, /* 16 bit FIFO Watermark */ Q_AL = 0x42, /* 8 bit FIFO Alignment */ Q_RSP = 0x44, /* 16 bit FIFO Read Shadow Pointer */ @@ -545,15 +633,16 @@ enum { }; #define Q_ADDR(reg, offs) (B8_Q_REGS + (reg) + (offs)) -/* Q_F 32 bit Flag Register */ +/* Q_TEST 32 bit Test Register */ enum { - F_ALM_FULL = 1<<27, /* Rx FIFO: almost full */ - F_EMPTY = 1<<27, /* Tx FIFO: empty flag */ - F_FIFO_EOF = 1<<26, /* Tag (EOF Flag) bit in FIFO */ - F_WM_REACHED = 1<<25, /* Watermark reached */ + /* Transmit */ + F_TX_CHK_AUTO_OFF = 1<<31, /* Tx checksum auto calc off (Yukon EX) */ + F_TX_CHK_AUTO_ON = 1<<30, /* Tx checksum auto calc off (Yukon EX) */ + + /* Receive */ F_M_RX_RAM_DIS = 1<<24, /* MAC Rx RAM Read Port disable */ - F_FIFO_LEVEL = 0x1fL<<16, /* Bit 23..16: # of Qwords in FIFO */ - F_WATER_MARK = 0x0007ffL, /* Bit 10.. 0: Watermark */ + + /* Hardware testbits not used */ }; /* Queue Prefetch Unit Offsets, use Y2_QADDR() to address (Yukon-2 only)*/ @@ -1149,7 +1238,7 @@ enum { PHY_M_IS_JABBER = 1<<0, /* Jabber */ PHY_M_DEF_MSK = PHY_M_IS_LSP_CHANGE | PHY_M_IS_LST_CHANGE - | PHY_M_IS_FIFO_ERROR, + | PHY_M_IS_DUP_CHANGE, PHY_M_AN_MSK = PHY_M_IS_AN_ERROR | PHY_M_IS_AN_COMPL, }; @@ -1608,6 +1697,16 @@ enum { RX_VLAN_STRIP_ON = 1<<25, /* enable VLAN stripping */ RX_VLAN_STRIP_OFF = 1<<24, /* disable VLAN stripping */ + RX_MACSEC_FLUSH_ON = 1<<23, + RX_MACSEC_FLUSH_OFF = 1<<22, + RX_MACSEC_ASF_FLUSH_ON = 1<<21, + RX_MACSEC_ASF_FLUSH_OFF = 1<<20, + + GMF_RX_OVER_ON = 1<<19, /* enable flushing on receive overrun */ + GMF_RX_OVER_OFF = 1<<18, /* disable flushing on receive overrun */ + GMF_ASF_RX_OVER_ON = 1<<17, /* enable flushing of ASF when overrun */ + GMF_ASF_RX_OVER_OFF = 1<<16, /* disable flushing of ASF when overrun */ + GMF_WP_TST_ON = 1<<14, /* Write Pointer Test On */ GMF_WP_TST_OFF = 1<<13, /* Write Pointer Test Off */ GMF_WP_STEP = 1<<12, /* Write Pointer Step/Increment */ @@ -1720,6 +1819,15 @@ enum { /* GMAC_CTRL 32 bit GMAC Control Reg (YUKON only) */ enum { + GMC_SET_RST = 1<<15,/* MAC SEC RST */ + GMC_SEC_RST_OFF = 1<<14,/* MAC SEC RSt OFF */ + GMC_BYP_MACSECRX_ON = 1<<13,/* Bypass macsec RX */ + GMC_BYP_MACSECRX_OFF= 1<<12,/* Bypass macsec RX off */ + GMC_BYP_MACSECTX_ON = 1<<11,/* Bypass macsec TX */ + GMC_BYP_MACSECTX_OFF= 1<<10,/* Bypass macsec TX off*/ + GMC_BYP_RETR_ON = 1<<9, /* Bypass retransmit FIFO On */ + GMC_BYP_RETR_OFF= 1<<8, /* Bypass retransmit FIFO Off */ + GMC_H_BURST_ON = 1<<7, /* Half Duplex Burst Mode On */ GMC_H_BURST_OFF = 1<<6, /* Half Duplex Burst Mode Off */ GMC_F_LOOPB_ON = 1<<5, /* FIFO Loopback On */ @@ -1732,28 +1840,6 @@ enum { /* GPHY_CTRL 32 bit GPHY Control Reg (YUKON only) */ enum { - GPC_SEL_BDT = 1<<28, /* Select Bi-Dir. Transfer for MDC/MDIO */ - GPC_INT_POL_HI = 1<<27, /* IRQ Polarity is Active HIGH */ - GPC_75_OHM = 1<<26, /* Use 75 Ohm Termination instead of 50 */ - GPC_DIS_FC = 1<<25, /* Disable Automatic Fiber/Copper Detection */ - GPC_DIS_SLEEP = 1<<24, /* Disable Energy Detect */ - GPC_HWCFG_M_3 = 1<<23, /* HWCFG_MODE[3] */ - GPC_HWCFG_M_2 = 1<<22, /* HWCFG_MODE[2] */ - GPC_HWCFG_M_1 = 1<<21, /* HWCFG_MODE[1] */ - GPC_HWCFG_M_0 = 1<<20, /* HWCFG_MODE[0] */ - GPC_ANEG_0 = 1<<19, /* ANEG[0] */ - GPC_ENA_XC = 1<<18, /* Enable MDI crossover */ - GPC_DIS_125 = 1<<17, /* Disable 125 MHz clock */ - GPC_ANEG_3 = 1<<16, /* ANEG[3] */ - GPC_ANEG_2 = 1<<15, /* ANEG[2] */ - GPC_ANEG_1 = 1<<14, /* ANEG[1] */ - GPC_ENA_PAUSE = 1<<13, /* Enable Pause (SYM_OR_REM) */ - GPC_PHYADDR_4 = 1<<12, /* Bit 4 of Phy Addr */ - GPC_PHYADDR_3 = 1<<11, /* Bit 3 of Phy Addr */ - GPC_PHYADDR_2 = 1<<10, /* Bit 2 of Phy Addr */ - GPC_PHYADDR_1 = 1<<9, /* Bit 1 of Phy Addr */ - GPC_PHYADDR_0 = 1<<8, /* Bit 0 of Phy Addr */ - /* Bits 7..2: reserved */ GPC_RST_CLR = 1<<1, /* Clear GPHY Reset */ GPC_RST_SET = 1<<0, /* Set GPHY Reset */ }; @@ -1827,9 +1913,13 @@ enum { OP_ADDR64VLAN = OP_ADDR64 | OP_VLAN, OP_LRGLEN = 0x24, OP_LRGLENVLAN = OP_LRGLEN | OP_VLAN, + OP_MSS = 0x28, + OP_MSSVLAN = OP_MSS | OP_VLAN, + OP_BUFFER = 0x40, OP_PACKET = 0x41, OP_LARGESEND = 0x43, + OP_LSOV2 = 0x45, /* YUKON-2 STATUS opcodes defines */ OP_RXSTAT = 0x60, @@ -1840,6 +1930,19 @@ enum { OP_RXTIMEVLAN = OP_RXTIMESTAMP | OP_RXVLAN, OP_RSS_HASH = 0x65, OP_TXINDEXLE = 0x68, + OP_MACSEC = 0x6c, + OP_PUTIDX = 0x70, +}; + +enum status_css { + CSS_TCPUDPCSOK = 1<<7, /* TCP / UDP checksum is ok */ + CSS_ISUDP = 1<<6, /* packet is a UDP packet */ + CSS_ISTCP = 1<<5, /* packet is a TCP packet */ + CSS_ISIPFRAG = 1<<4, /* packet is a TCP/UDP frag, CS calc not done */ + CSS_ISIPV6 = 1<<3, /* packet is a IPv6 packet */ + CSS_IPV4CSUMOK = 1<<2, /* IP v4: TCP header checksum is ok */ + CSS_ISIPV4 = 1<<1, /* packet is a IPv4 packet */ + CSS_LINK_BIT = 1<<0, /* port number (legacy) */ }; /* Yukon 2 hardware interface */ @@ -1860,7 +1963,7 @@ struct sky2_rx_le { struct sky2_status_le { __le32 status; /* also checksum */ __le16 length; /* also vlan tag */ - u8 link; + u8 css; u8 opcode; } __attribute((packed)); @@ -1895,6 +1998,7 @@ struct sky2_port { struct sky2_tx_le *tx_le; u16 tx_cons; /* next le to check */ u16 tx_prod; /* next le to use */ + u16 tx_next; /* debug only */ u32 tx_addr64; u16 tx_pending; u16 tx_last_mss; @@ -1925,6 +2029,9 @@ struct sky2_port { enum flow_control flow_mode; enum flow_control flow_status; +#ifdef CONFIG_SKY2_DEBUG + struct dentry *debugfs; +#endif struct net_device_stats net_stats; }; |