diff options
Diffstat (limited to 'drivers/net/phy/at803x.c')
| -rw-r--r-- | drivers/net/phy/at803x.c | 312 |
1 files changed, 301 insertions, 11 deletions
diff --git a/drivers/net/phy/at803x.c b/drivers/net/phy/at803x.c index 1eb5d4fb8925..aee62610bade 100644 --- a/drivers/net/phy/at803x.c +++ b/drivers/net/phy/at803x.c @@ -2,7 +2,7 @@ /* * drivers/net/phy/at803x.c * - * Driver for Atheros 803x PHY + * Driver for Qualcomm Atheros AR803x PHY * * Author: Matus Ujhelyi <ujhelyi.m@gmail.com> */ @@ -13,7 +13,12 @@ #include <linux/netdevice.h> #include <linux/etherdevice.h> #include <linux/of_gpio.h> +#include <linux/bitfield.h> #include <linux/gpio/consumer.h> +#include <linux/regulator/of_regulator.h> +#include <linux/regulator/driver.h> +#include <linux/regulator/consumer.h> +#include <dt-bindings/net/qca-ar803x.h> #define AT803X_SPECIFIC_STATUS 0x11 #define AT803X_SS_SPEED_MASK (3 << 14) @@ -62,17 +67,60 @@ #define AT803X_DEBUG_REG_5 0x05 #define AT803X_DEBUG_TX_CLK_DLY_EN BIT(8) +#define AT803X_DEBUG_REG_1F 0x1F +#define AT803X_DEBUG_PLL_ON BIT(2) +#define AT803X_DEBUG_RGMII_1V8 BIT(3) + +/* AT803x supports either the XTAL input pad, an internal PLL or the + * DSP as clock reference for the clock output pad. The XTAL reference + * is only used for 25 MHz output, all other frequencies need the PLL. + * The DSP as a clock reference is used in synchronous ethernet + * applications. + * + * By default the PLL is only enabled if there is a link. Otherwise + * the PHY will go into low power state and disabled the PLL. You can + * set the PLL_ON bit (see debug register 0x1f) to keep the PLL always + * enabled. + */ +#define AT803X_MMD7_CLK25M 0x8016 +#define AT803X_CLK_OUT_MASK GENMASK(4, 2) +#define AT803X_CLK_OUT_25MHZ_XTAL 0 +#define AT803X_CLK_OUT_25MHZ_DSP 1 +#define AT803X_CLK_OUT_50MHZ_PLL 2 +#define AT803X_CLK_OUT_50MHZ_DSP 3 +#define AT803X_CLK_OUT_62_5MHZ_PLL 4 +#define AT803X_CLK_OUT_62_5MHZ_DSP 5 +#define AT803X_CLK_OUT_125MHZ_PLL 6 +#define AT803X_CLK_OUT_125MHZ_DSP 7 + +/* The AR8035 has another mask which is compatible with the AR8031/AR8033 mask + * but doesn't support choosing between XTAL/PLL and DSP. + */ +#define AT8035_CLK_OUT_MASK GENMASK(4, 3) + +#define AT803X_CLK_OUT_STRENGTH_MASK GENMASK(8, 7) +#define AT803X_CLK_OUT_STRENGTH_FULL 0 +#define AT803X_CLK_OUT_STRENGTH_HALF 1 +#define AT803X_CLK_OUT_STRENGTH_QUARTER 2 + +#define ATH9331_PHY_ID 0x004dd041 #define ATH8030_PHY_ID 0x004dd076 #define ATH8031_PHY_ID 0x004dd074 #define ATH8035_PHY_ID 0x004dd072 #define AT803X_PHY_ID_MASK 0xffffffef -MODULE_DESCRIPTION("Atheros 803x PHY driver"); +MODULE_DESCRIPTION("Qualcomm Atheros AR803x PHY driver"); MODULE_AUTHOR("Matus Ujhelyi"); MODULE_LICENSE("GPL"); struct at803x_priv { - bool phy_reset:1; + int flags; +#define AT803X_KEEP_PLL_ENABLED BIT(0) /* don't turn off internal PLL */ + u16 clk_25m_reg; + u16 clk_25m_mask; + struct regulator_dev *vddio_rdev; + struct regulator_dev *vddh_rdev; + struct regulator *vddio; }; struct at803x_context { @@ -240,6 +288,193 @@ static int at803x_resume(struct phy_device *phydev) return phy_modify(phydev, MII_BMCR, BMCR_PDOWN | BMCR_ISOLATE, 0); } +static int at803x_rgmii_reg_set_voltage_sel(struct regulator_dev *rdev, + unsigned int selector) +{ + struct phy_device *phydev = rdev_get_drvdata(rdev); + + if (selector) + return at803x_debug_reg_mask(phydev, AT803X_DEBUG_REG_1F, + 0, AT803X_DEBUG_RGMII_1V8); + else + return at803x_debug_reg_mask(phydev, AT803X_DEBUG_REG_1F, + AT803X_DEBUG_RGMII_1V8, 0); +} + +static int at803x_rgmii_reg_get_voltage_sel(struct regulator_dev *rdev) +{ + struct phy_device *phydev = rdev_get_drvdata(rdev); + int val; + + val = at803x_debug_reg_read(phydev, AT803X_DEBUG_REG_1F); + if (val < 0) + return val; + + return (val & AT803X_DEBUG_RGMII_1V8) ? 1 : 0; +} + +static struct regulator_ops vddio_regulator_ops = { + .list_voltage = regulator_list_voltage_table, + .set_voltage_sel = at803x_rgmii_reg_set_voltage_sel, + .get_voltage_sel = at803x_rgmii_reg_get_voltage_sel, +}; + +static const unsigned int vddio_voltage_table[] = { + 1500000, + 1800000, +}; + +static const struct regulator_desc vddio_desc = { + .name = "vddio", + .of_match = of_match_ptr("vddio-regulator"), + .n_voltages = ARRAY_SIZE(vddio_voltage_table), + .volt_table = vddio_voltage_table, + .ops = &vddio_regulator_ops, + .type = REGULATOR_VOLTAGE, + .owner = THIS_MODULE, +}; + +static struct regulator_ops vddh_regulator_ops = { +}; + +static const struct regulator_desc vddh_desc = { + .name = "vddh", + .of_match = of_match_ptr("vddh-regulator"), + .n_voltages = 1, + .fixed_uV = 2500000, + .ops = &vddh_regulator_ops, + .type = REGULATOR_VOLTAGE, + .owner = THIS_MODULE, +}; + +static int at8031_register_regulators(struct phy_device *phydev) +{ + struct at803x_priv *priv = phydev->priv; + struct device *dev = &phydev->mdio.dev; + struct regulator_config config = { }; + + config.dev = dev; + config.driver_data = phydev; + + priv->vddio_rdev = devm_regulator_register(dev, &vddio_desc, &config); + if (IS_ERR(priv->vddio_rdev)) { + phydev_err(phydev, "failed to register VDDIO regulator\n"); + return PTR_ERR(priv->vddio_rdev); + } + + priv->vddh_rdev = devm_regulator_register(dev, &vddh_desc, &config); + if (IS_ERR(priv->vddh_rdev)) { + phydev_err(phydev, "failed to register VDDH regulator\n"); + return PTR_ERR(priv->vddh_rdev); + } + + return 0; +} + +static bool at803x_match_phy_id(struct phy_device *phydev, u32 phy_id) +{ + return (phydev->phy_id & phydev->drv->phy_id_mask) + == (phy_id & phydev->drv->phy_id_mask); +} + +static int at803x_parse_dt(struct phy_device *phydev) +{ + struct device_node *node = phydev->mdio.dev.of_node; + struct at803x_priv *priv = phydev->priv; + unsigned int sel, mask; + u32 freq, strength; + int ret; + + if (!IS_ENABLED(CONFIG_OF_MDIO)) + return 0; + + ret = of_property_read_u32(node, "qca,clk-out-frequency", &freq); + if (!ret) { + mask = AT803X_CLK_OUT_MASK; + switch (freq) { + case 25000000: + sel = AT803X_CLK_OUT_25MHZ_XTAL; + break; + case 50000000: + sel = AT803X_CLK_OUT_50MHZ_PLL; + break; + case 62500000: + sel = AT803X_CLK_OUT_62_5MHZ_PLL; + break; + case 125000000: + sel = AT803X_CLK_OUT_125MHZ_PLL; + break; + default: + phydev_err(phydev, "invalid qca,clk-out-frequency\n"); + return -EINVAL; + } + + priv->clk_25m_reg |= FIELD_PREP(mask, sel); + priv->clk_25m_mask |= mask; + + /* Fixup for the AR8030/AR8035. This chip has another mask and + * doesn't support the DSP reference. Eg. the lowest bit of the + * mask. The upper two bits select the same frequencies. Mask + * the lowest bit here. + * + * Warning: + * There was no datasheet for the AR8030 available so this is + * just a guess. But the AR8035 is listed as pin compatible + * to the AR8030 so there might be a good chance it works on + * the AR8030 too. + */ + if (at803x_match_phy_id(phydev, ATH8030_PHY_ID) || + at803x_match_phy_id(phydev, ATH8035_PHY_ID)) { + priv->clk_25m_reg &= ~AT8035_CLK_OUT_MASK; + priv->clk_25m_mask &= ~AT8035_CLK_OUT_MASK; + } + } + + ret = of_property_read_u32(node, "qca,clk-out-strength", &strength); + if (!ret) { + priv->clk_25m_mask |= AT803X_CLK_OUT_STRENGTH_MASK; + switch (strength) { + case AR803X_STRENGTH_FULL: + priv->clk_25m_reg |= AT803X_CLK_OUT_STRENGTH_FULL; + break; + case AR803X_STRENGTH_HALF: + priv->clk_25m_reg |= AT803X_CLK_OUT_STRENGTH_HALF; + break; + case AR803X_STRENGTH_QUARTER: + priv->clk_25m_reg |= AT803X_CLK_OUT_STRENGTH_QUARTER; + break; + default: + phydev_err(phydev, "invalid qca,clk-out-strength\n"); + return -EINVAL; + } + } + + /* Only supported on AR8031/AR8033, the AR8030/AR8035 use strapping + * options. + */ + if (at803x_match_phy_id(phydev, ATH8031_PHY_ID)) { + if (of_property_read_bool(node, "qca,keep-pll-enabled")) + priv->flags |= AT803X_KEEP_PLL_ENABLED; + + ret = at8031_register_regulators(phydev); + if (ret < 0) + return ret; + + priv->vddio = devm_regulator_get_optional(&phydev->mdio.dev, + "vddio"); + if (IS_ERR(priv->vddio)) { + phydev_err(phydev, "failed to get VDDIO regulator\n"); + return PTR_ERR(priv->vddio); + } + + ret = regulator_enable(priv->vddio); + if (ret < 0) + return ret; + } + + return 0; +} + static int at803x_probe(struct phy_device *phydev) { struct device *dev = &phydev->mdio.dev; @@ -251,7 +486,40 @@ static int at803x_probe(struct phy_device *phydev) phydev->priv = priv; - return 0; + return at803x_parse_dt(phydev); +} + +static int at803x_clk_out_config(struct phy_device *phydev) +{ + struct at803x_priv *priv = phydev->priv; + int val; + + if (!priv->clk_25m_mask) + return 0; + + val = phy_read_mmd(phydev, MDIO_MMD_AN, AT803X_MMD7_CLK25M); + if (val < 0) + return val; + + val &= ~priv->clk_25m_mask; + val |= priv->clk_25m_reg; + + return phy_write_mmd(phydev, MDIO_MMD_AN, AT803X_MMD7_CLK25M, val); +} + +static int at8031_pll_config(struct phy_device *phydev) +{ + struct at803x_priv *priv = phydev->priv; + + /* The default after hardware reset is PLL OFF. After a soft reset, the + * values are retained. + */ + if (priv->flags & AT803X_KEEP_PLL_ENABLED) + return at803x_debug_reg_mask(phydev, AT803X_DEBUG_REG_1F, + 0, AT803X_DEBUG_PLL_ON); + else + return at803x_debug_reg_mask(phydev, AT803X_DEBUG_REG_1F, + AT803X_DEBUG_PLL_ON, 0); } static int at803x_config_init(struct phy_device *phydev) @@ -276,8 +544,20 @@ static int at803x_config_init(struct phy_device *phydev) ret = at803x_enable_tx_delay(phydev); else ret = at803x_disable_tx_delay(phydev); + if (ret < 0) + return ret; - return ret; + ret = at803x_clk_out_config(phydev); + if (ret < 0) + return ret; + + if (at803x_match_phy_id(phydev, ATH8031_PHY_ID)) { + ret = at8031_pll_config(phydev); + if (ret < 0) + return ret; + } + + return 0; } static int at803x_ack_interrupt(struct phy_device *phydev) @@ -426,9 +706,9 @@ static int at803x_read_status(struct phy_device *phydev) static struct phy_driver at803x_driver[] = { { - /* ATHEROS 8035 */ + /* Qualcomm Atheros AR8035 */ .phy_id = ATH8035_PHY_ID, - .name = "Atheros 8035 ethernet", + .name = "Qualcomm Atheros AR8035", .phy_id_mask = AT803X_PHY_ID_MASK, .probe = at803x_probe, .config_init = at803x_config_init, @@ -441,9 +721,9 @@ static struct phy_driver at803x_driver[] = { .ack_interrupt = at803x_ack_interrupt, .config_intr = at803x_config_intr, }, { - /* ATHEROS 8030 */ + /* Qualcomm Atheros AR8030 */ .phy_id = ATH8030_PHY_ID, - .name = "Atheros 8030 ethernet", + .name = "Qualcomm Atheros AR8030", .phy_id_mask = AT803X_PHY_ID_MASK, .probe = at803x_probe, .config_init = at803x_config_init, @@ -456,9 +736,9 @@ static struct phy_driver at803x_driver[] = { .ack_interrupt = at803x_ack_interrupt, .config_intr = at803x_config_intr, }, { - /* ATHEROS 8031 */ + /* Qualcomm Atheros AR8031/AR8033 */ .phy_id = ATH8031_PHY_ID, - .name = "Atheros 8031 ethernet", + .name = "Qualcomm Atheros AR8031/AR8033", .phy_id_mask = AT803X_PHY_ID_MASK, .probe = at803x_probe, .config_init = at803x_config_init, @@ -471,6 +751,15 @@ static struct phy_driver at803x_driver[] = { .aneg_done = at803x_aneg_done, .ack_interrupt = &at803x_ack_interrupt, .config_intr = &at803x_config_intr, +}, { + /* ATHEROS AR9331 */ + PHY_ID_MATCH_EXACT(ATH9331_PHY_ID), + .name = "Qualcomm Atheros AR9331 built-in PHY", + .suspend = at803x_suspend, + .resume = at803x_resume, + /* PHY_BASIC_FEATURES */ + .ack_interrupt = &at803x_ack_interrupt, + .config_intr = &at803x_config_intr, } }; module_phy_driver(at803x_driver); @@ -479,6 +768,7 @@ static struct mdio_device_id __maybe_unused atheros_tbl[] = { { ATH8030_PHY_ID, AT803X_PHY_ID_MASK }, { ATH8031_PHY_ID, AT803X_PHY_ID_MASK }, { ATH8035_PHY_ID, AT803X_PHY_ID_MASK }, + { PHY_ID_MATCH_EXACT(ATH9331_PHY_ID) }, { } }; |