diff options
Diffstat (limited to 'drivers/net/ethernet/intel/e1000/e1000_hw.c')
| -rw-r--r-- | drivers/net/ethernet/intel/e1000/e1000_hw.c | 558 |
1 files changed, 309 insertions, 249 deletions
diff --git a/drivers/net/ethernet/intel/e1000/e1000_hw.c b/drivers/net/ethernet/intel/e1000/e1000_hw.c index 8fedd2451538..2879b9631e15 100644 --- a/drivers/net/ethernet/intel/e1000/e1000_hw.c +++ b/drivers/net/ethernet/intel/e1000/e1000_hw.c @@ -164,8 +164,9 @@ static void e1000_phy_init_script(struct e1000_hw *hw) if (hw->phy_init_script) { msleep(20); - /* Save off the current value of register 0x2F5B to be restored at - * the end of this routine. */ + /* Save off the current value of register 0x2F5B to be restored + * at the end of this routine. + */ ret_val = e1000_read_phy_reg(hw, 0x2F5B, &phy_saved_data); /* Disabled the PHY transmitter */ @@ -466,7 +467,8 @@ s32 e1000_reset_hw(struct e1000_hw *hw) case e1000_82541: case e1000_82541_rev_2: /* These controllers can't ack the 64-bit write when issuing the - * reset, so use IO-mapping as a workaround to issue the reset */ + * reset, so use IO-mapping as a workaround to issue the reset + */ E1000_WRITE_REG_IO(hw, CTRL, (ctrl | E1000_CTRL_RST)); break; case e1000_82545_rev_3: @@ -480,9 +482,9 @@ s32 e1000_reset_hw(struct e1000_hw *hw) break; } - /* After MAC reset, force reload of EEPROM to restore power-on settings to - * device. Later controllers reload the EEPROM automatically, so just wait - * for reload to complete. + /* After MAC reset, force reload of EEPROM to restore power-on settings + * to device. Later controllers reload the EEPROM automatically, so + * just wait for reload to complete. */ switch (hw->mac_type) { case e1000_82542_rev2_0: @@ -591,8 +593,8 @@ s32 e1000_init_hw(struct e1000_hw *hw) msleep(5); } - /* Setup the receive address. This involves initializing all of the Receive - * Address Registers (RARs 0 - 15). + /* Setup the receive address. This involves initializing all of the + * Receive Address Registers (RARs 0 - 15). */ e1000_init_rx_addrs(hw); @@ -611,7 +613,8 @@ s32 e1000_init_hw(struct e1000_hw *hw) for (i = 0; i < mta_size; i++) { E1000_WRITE_REG_ARRAY(hw, MTA, i, 0); /* use write flush to prevent Memory Write Block (MWB) from - * occurring when accessing our register space */ + * occurring when accessing our register space + */ E1000_WRITE_FLUSH(); } @@ -630,7 +633,9 @@ s32 e1000_init_hw(struct e1000_hw *hw) case e1000_82546_rev_3: break; default: - /* Workaround for PCI-X problem when BIOS sets MMRBC incorrectly. */ + /* Workaround for PCI-X problem when BIOS sets MMRBC + * incorrectly. + */ if (hw->bus_type == e1000_bus_type_pcix && e1000_pcix_get_mmrbc(hw) > 2048) e1000_pcix_set_mmrbc(hw, 2048); @@ -660,7 +665,8 @@ s32 e1000_init_hw(struct e1000_hw *hw) hw->device_id == E1000_DEV_ID_82546GB_QUAD_COPPER_KSP3) { ctrl_ext = er32(CTRL_EXT); /* Relaxed ordering must be disabled to avoid a parity - * error crash in a PCI slot. */ + * error crash in a PCI slot. + */ ctrl_ext |= E1000_CTRL_EXT_RO_DIS; ew32(CTRL_EXT, ctrl_ext); } @@ -810,8 +816,9 @@ s32 e1000_setup_link(struct e1000_hw *hw) ew32(FCRTL, 0); ew32(FCRTH, 0); } else { - /* We need to set up the Receive Threshold high and low water marks - * as well as (optionally) enabling the transmission of XON frames. + /* We need to set up the Receive Threshold high and low water + * marks as well as (optionally) enabling the transmission of + * XON frames. */ if (hw->fc_send_xon) { ew32(FCRTL, (hw->fc_low_water | E1000_FCRTL_XONE)); @@ -868,42 +875,46 @@ static s32 e1000_setup_fiber_serdes_link(struct e1000_hw *hw) e1000_config_collision_dist(hw); /* Check for a software override of the flow control settings, and setup - * the device accordingly. If auto-negotiation is enabled, then software - * will have to set the "PAUSE" bits to the correct value in the Tranmsit - * Config Word Register (TXCW) and re-start auto-negotiation. However, if - * auto-negotiation is disabled, then software will have to manually - * configure the two flow control enable bits in the CTRL register. + * the device accordingly. If auto-negotiation is enabled, then + * software will have to set the "PAUSE" bits to the correct value in + * the Tranmsit Config Word Register (TXCW) and re-start + * auto-negotiation. However, if auto-negotiation is disabled, then + * software will have to manually configure the two flow control enable + * bits in the CTRL register. * * The possible values of the "fc" parameter are: - * 0: Flow control is completely disabled - * 1: Rx flow control is enabled (we can receive pause frames, but - * not send pause frames). - * 2: Tx flow control is enabled (we can send pause frames but we do - * not support receiving pause frames). - * 3: Both Rx and TX flow control (symmetric) are enabled. + * 0: Flow control is completely disabled + * 1: Rx flow control is enabled (we can receive pause frames, but + * not send pause frames). + * 2: Tx flow control is enabled (we can send pause frames but we do + * not support receiving pause frames). + * 3: Both Rx and TX flow control (symmetric) are enabled. */ switch (hw->fc) { case E1000_FC_NONE: - /* Flow control is completely disabled by a software over-ride. */ + /* Flow ctrl is completely disabled by a software over-ride */ txcw = (E1000_TXCW_ANE | E1000_TXCW_FD); break; case E1000_FC_RX_PAUSE: - /* RX Flow control is enabled and TX Flow control is disabled by a - * software over-ride. Since there really isn't a way to advertise - * that we are capable of RX Pause ONLY, we will advertise that we - * support both symmetric and asymmetric RX PAUSE. Later, we will - * disable the adapter's ability to send PAUSE frames. + /* Rx Flow control is enabled and Tx Flow control is disabled by + * a software over-ride. Since there really isn't a way to + * advertise that we are capable of Rx Pause ONLY, we will + * advertise that we support both symmetric and asymmetric Rx + * PAUSE. Later, we will disable the adapter's ability to send + * PAUSE frames. */ txcw = (E1000_TXCW_ANE | E1000_TXCW_FD | E1000_TXCW_PAUSE_MASK); break; case E1000_FC_TX_PAUSE: - /* TX Flow control is enabled, and RX Flow control is disabled, by a - * software over-ride. + /* Tx Flow control is enabled, and Rx Flow control is disabled, + * by a software over-ride. */ txcw = (E1000_TXCW_ANE | E1000_TXCW_FD | E1000_TXCW_ASM_DIR); break; case E1000_FC_FULL: - /* Flow control (both RX and TX) is enabled by a software over-ride. */ + /* Flow control (both Rx and Tx) is enabled by a software + * over-ride. + */ txcw = (E1000_TXCW_ANE | E1000_TXCW_FD | E1000_TXCW_PAUSE_MASK); break; default: @@ -912,11 +923,11 @@ static s32 e1000_setup_fiber_serdes_link(struct e1000_hw *hw) break; } - /* Since auto-negotiation is enabled, take the link out of reset (the link - * will be in reset, because we previously reset the chip). This will - * restart auto-negotiation. If auto-negotiation is successful then the - * link-up status bit will be set and the flow control enable bits (RFCE - * and TFCE) will be set according to their negotiated value. + /* Since auto-negotiation is enabled, take the link out of reset (the + * link will be in reset, because we previously reset the chip). This + * will restart auto-negotiation. If auto-negotiation is successful + * then the link-up status bit will be set and the flow control enable + * bits (RFCE and TFCE) will be set according to their negotiated value. */ e_dbg("Auto-negotiation enabled\n"); @@ -927,11 +938,12 @@ static s32 e1000_setup_fiber_serdes_link(struct e1000_hw *hw) hw->txcw = txcw; msleep(1); - /* If we have a signal (the cable is plugged in) then poll for a "Link-Up" - * indication in the Device Status Register. Time-out if a link isn't - * seen in 500 milliseconds seconds (Auto-negotiation should complete in - * less than 500 milliseconds even if the other end is doing it in SW). - * For internal serdes, we just assume a signal is present, then poll. + /* If we have a signal (the cable is plugged in) then poll for a + * "Link-Up" indication in the Device Status Register. Time-out if a + * link isn't seen in 500 milliseconds seconds (Auto-negotiation should + * complete in less than 500 milliseconds even if the other end is doing + * it in SW). For internal serdes, we just assume a signal is present, + * then poll. */ if (hw->media_type == e1000_media_type_internal_serdes || (er32(CTRL) & E1000_CTRL_SWDPIN1) == signal) { @@ -946,9 +958,9 @@ static s32 e1000_setup_fiber_serdes_link(struct e1000_hw *hw) e_dbg("Never got a valid link from auto-neg!!!\n"); hw->autoneg_failed = 1; /* AutoNeg failed to achieve a link, so we'll call - * e1000_check_for_link. This routine will force the link up if - * we detect a signal. This will allow us to communicate with - * non-autonegotiating link partners. + * e1000_check_for_link. This routine will force the + * link up if we detect a signal. This will allow us to + * communicate with non-autonegotiating link partners. */ ret_val = e1000_check_for_link(hw); if (ret_val) { @@ -1042,9 +1054,9 @@ static s32 e1000_copper_link_preconfig(struct e1000_hw *hw) e_dbg("e1000_copper_link_preconfig"); ctrl = er32(CTRL); - /* With 82543, we need to force speed and duplex on the MAC equal to what - * the PHY speed and duplex configuration is. In addition, we need to - * perform a hardware reset on the PHY to take it out of reset. + /* With 82543, we need to force speed and duplex on the MAC equal to + * what the PHY speed and duplex configuration is. In addition, we need + * to perform a hardware reset on the PHY to take it out of reset. */ if (hw->mac_type > e1000_82543) { ctrl |= E1000_CTRL_SLU; @@ -1175,7 +1187,8 @@ static s32 e1000_copper_link_igp_setup(struct e1000_hw *hw) /* when autonegotiation advertisement is only 1000Mbps then we * should disable SmartSpeed and enable Auto MasterSlave - * resolution as hardware default. */ + * resolution as hardware default. + */ if (hw->autoneg_advertised == ADVERTISE_1000_FULL) { /* Disable SmartSpeed */ ret_val = @@ -1485,13 +1498,15 @@ static s32 e1000_setup_copper_link(struct e1000_hw *hw) if (hw->autoneg) { /* Setup autoneg and flow control advertisement - * and perform autonegotiation */ + * and perform autonegotiation + */ ret_val = e1000_copper_link_autoneg(hw); if (ret_val) return ret_val; } else { /* PHY will be set to 10H, 10F, 100H,or 100F - * depending on value from forced_speed_duplex. */ + * depending on value from forced_speed_duplex. + */ e_dbg("Forcing speed and duplex\n"); ret_val = e1000_phy_force_speed_duplex(hw); if (ret_val) { @@ -1609,7 +1624,8 @@ s32 e1000_phy_setup_autoneg(struct e1000_hw *hw) * setup the PHY advertisement registers accordingly. If * auto-negotiation is enabled, then software will have to set the * "PAUSE" bits to the correct value in the Auto-Negotiation - * Advertisement Register (PHY_AUTONEG_ADV) and re-start auto-negotiation. + * Advertisement Register (PHY_AUTONEG_ADV) and re-start + * auto-negotiation. * * The possible values of the "fc" parameter are: * 0: Flow control is completely disabled @@ -1636,7 +1652,7 @@ s32 e1000_phy_setup_autoneg(struct e1000_hw *hw) * capable of RX Pause ONLY, we will advertise that we * support both symmetric and asymmetric RX PAUSE. Later * (in e1000_config_fc_after_link_up) we will disable the - *hw's ability to send PAUSE frames. + * hw's ability to send PAUSE frames. */ mii_autoneg_adv_reg |= (NWAY_AR_ASM_DIR | NWAY_AR_PAUSE); break; @@ -1720,15 +1736,15 @@ static s32 e1000_phy_force_speed_duplex(struct e1000_hw *hw) /* Are we forcing Full or Half Duplex? */ if (hw->forced_speed_duplex == e1000_100_full || hw->forced_speed_duplex == e1000_10_full) { - /* We want to force full duplex so we SET the full duplex bits in the - * Device and MII Control Registers. + /* We want to force full duplex so we SET the full duplex bits + * in the Device and MII Control Registers. */ ctrl |= E1000_CTRL_FD; mii_ctrl_reg |= MII_CR_FULL_DUPLEX; e_dbg("Full Duplex\n"); } else { - /* We want to force half duplex so we CLEAR the full duplex bits in - * the Device and MII Control Registers. + /* We want to force half duplex so we CLEAR the full duplex bits + * in the Device and MII Control Registers. */ ctrl &= ~E1000_CTRL_FD; mii_ctrl_reg &= ~MII_CR_FULL_DUPLEX; @@ -1762,8 +1778,8 @@ static s32 e1000_phy_force_speed_duplex(struct e1000_hw *hw) if (ret_val) return ret_val; - /* Clear Auto-Crossover to force MDI manually. M88E1000 requires MDI - * forced whenever speed are duplex are forced. + /* Clear Auto-Crossover to force MDI manually. M88E1000 requires + * MDI forced whenever speed are duplex are forced. */ phy_data &= ~M88E1000_PSCR_AUTO_X_MODE; ret_val = @@ -1814,10 +1830,10 @@ static s32 e1000_phy_force_speed_duplex(struct e1000_hw *hw) e_dbg("Waiting for forced speed/duplex link.\n"); mii_status_reg = 0; - /* We will wait for autoneg to complete or 4.5 seconds to expire. */ + /* Wait for autoneg to complete or 4.5 seconds to expire */ for (i = PHY_FORCE_TIME; i > 0; i--) { - /* Read the MII Status Register and wait for Auto-Neg Complete bit - * to be set. + /* Read the MII Status Register and wait for Auto-Neg + * Complete bit to be set. */ ret_val = e1000_read_phy_reg(hw, PHY_STATUS, &mii_status_reg); @@ -1834,20 +1850,24 @@ static s32 e1000_phy_force_speed_duplex(struct e1000_hw *hw) msleep(100); } if ((i == 0) && (hw->phy_type == e1000_phy_m88)) { - /* We didn't get link. Reset the DSP and wait again for link. */ + /* We didn't get link. Reset the DSP and wait again + * for link. + */ ret_val = e1000_phy_reset_dsp(hw); if (ret_val) { e_dbg("Error Resetting PHY DSP\n"); return ret_val; } } - /* This loop will early-out if the link condition has been met. */ + /* This loop will early-out if the link condition has been + * met + */ for (i = PHY_FORCE_TIME; i > 0; i--) { if (mii_status_reg & MII_SR_LINK_STATUS) break; msleep(100); - /* Read the MII Status Register and wait for Auto-Neg Complete bit - * to be set. + /* Read the MII Status Register and wait for Auto-Neg + * Complete bit to be set. */ ret_val = e1000_read_phy_reg(hw, PHY_STATUS, &mii_status_reg); @@ -1862,9 +1882,10 @@ static s32 e1000_phy_force_speed_duplex(struct e1000_hw *hw) } if (hw->phy_type == e1000_phy_m88) { - /* Because we reset the PHY above, we need to re-force TX_CLK in the - * Extended PHY Specific Control Register to 25MHz clock. This value - * defaults back to a 2.5MHz clock when the PHY is reset. + /* Because we reset the PHY above, we need to re-force TX_CLK in + * the Extended PHY Specific Control Register to 25MHz clock. + * This value defaults back to a 2.5MHz clock when the PHY is + * reset. */ ret_val = e1000_read_phy_reg(hw, M88E1000_EXT_PHY_SPEC_CTRL, @@ -1879,8 +1900,9 @@ static s32 e1000_phy_force_speed_duplex(struct e1000_hw *hw) if (ret_val) return ret_val; - /* In addition, because of the s/w reset above, we need to enable CRS on - * TX. This must be set for both full and half duplex operation. + /* In addition, because of the s/w reset above, we need to + * enable CRS on Tx. This must be set for both full and half + * duplex operation. */ ret_val = e1000_read_phy_reg(hw, M88E1000_PHY_SPEC_CTRL, &phy_data); @@ -1951,7 +1973,8 @@ static s32 e1000_config_mac_to_phy(struct e1000_hw *hw) e_dbg("e1000_config_mac_to_phy"); /* 82544 or newer MAC, Auto Speed Detection takes care of - * MAC speed/duplex configuration.*/ + * MAC speed/duplex configuration. + */ if ((hw->mac_type >= e1000_82544) && (hw->mac_type != e1000_ce4100)) return E1000_SUCCESS; @@ -1985,7 +2008,7 @@ static s32 e1000_config_mac_to_phy(struct e1000_hw *hw) * registers depending on negotiated values. */ ret_val = e1000_read_phy_reg(hw, M88E1000_PHY_SPEC_STATUS, - &phy_data); + &phy_data); if (ret_val) return ret_val; @@ -2002,7 +2025,7 @@ static s32 e1000_config_mac_to_phy(struct e1000_hw *hw) if ((phy_data & M88E1000_PSSR_SPEED) == M88E1000_PSSR_1000MBS) ctrl |= E1000_CTRL_SPD_1000; else if ((phy_data & M88E1000_PSSR_SPEED) == - M88E1000_PSSR_100MBS) + M88E1000_PSSR_100MBS) ctrl |= E1000_CTRL_SPD_100; } @@ -2135,9 +2158,9 @@ static s32 e1000_config_fc_after_link_up(struct e1000_hw *hw) if (mii_status_reg & MII_SR_AUTONEG_COMPLETE) { /* The AutoNeg process has completed, so we now need to * read both the Auto Negotiation Advertisement Register - * (Address 4) and the Auto_Negotiation Base Page Ability - * Register (Address 5) to determine how flow control was - * negotiated. + * (Address 4) and the Auto_Negotiation Base Page + * Ability Register (Address 5) to determine how flow + * control was negotiated. */ ret_val = e1000_read_phy_reg(hw, PHY_AUTONEG_ADV, &mii_nway_adv_reg); @@ -2148,18 +2171,19 @@ static s32 e1000_config_fc_after_link_up(struct e1000_hw *hw) if (ret_val) return ret_val; - /* Two bits in the Auto Negotiation Advertisement Register - * (Address 4) and two bits in the Auto Negotiation Base - * Page Ability Register (Address 5) determine flow control - * for both the PHY and the link partner. The following - * table, taken out of the IEEE 802.3ab/D6.0 dated March 25, - * 1999, describes these PAUSE resolution bits and how flow - * control is determined based upon these settings. + /* Two bits in the Auto Negotiation Advertisement + * Register (Address 4) and two bits in the Auto + * Negotiation Base Page Ability Register (Address 5) + * determine flow control for both the PHY and the link + * partner. The following table, taken out of the IEEE + * 802.3ab/D6.0 dated March 25, 1999, describes these + * PAUSE resolution bits and how flow control is + * determined based upon these settings. * NOTE: DC = Don't Care * * LOCAL DEVICE | LINK PARTNER * PAUSE | ASM_DIR | PAUSE | ASM_DIR | NIC Resolution - *-------|---------|-------|---------|-------------------- + *-------|---------|-------|---------|------------------ * 0 | 0 | DC | DC | E1000_FC_NONE * 0 | 1 | 0 | DC | E1000_FC_NONE * 0 | 1 | 1 | 0 | E1000_FC_NONE @@ -2178,17 +2202,18 @@ static s32 e1000_config_fc_after_link_up(struct e1000_hw *hw) * * LOCAL DEVICE | LINK PARTNER * PAUSE | ASM_DIR | PAUSE | ASM_DIR | Result - *-------|---------|-------|---------|-------------------- + *-------|---------|-------|---------|------------------ * 1 | DC | 1 | DC | E1000_FC_FULL * */ if ((mii_nway_adv_reg & NWAY_AR_PAUSE) && (mii_nway_lp_ability_reg & NWAY_LPAR_PAUSE)) { - /* Now we need to check if the user selected RX ONLY - * of pause frames. In this case, we had to advertise - * FULL flow control because we could not advertise RX - * ONLY. Hence, we must now check to see if we need to - * turn OFF the TRANSMISSION of PAUSE frames. + /* Now we need to check if the user selected Rx + * ONLY of pause frames. In this case, we had + * to advertise FULL flow control because we + * could not advertise Rx ONLY. Hence, we must + * now check to see if we need to turn OFF the + * TRANSMISSION of PAUSE frames. */ if (hw->original_fc == E1000_FC_FULL) { hw->fc = E1000_FC_FULL; @@ -2203,7 +2228,7 @@ static s32 e1000_config_fc_after_link_up(struct e1000_hw *hw) * * LOCAL DEVICE | LINK PARTNER * PAUSE | ASM_DIR | PAUSE | ASM_DIR | Result - *-------|---------|-------|---------|-------------------- + *-------|---------|-------|---------|------------------ * 0 | 1 | 1 | 1 | E1000_FC_TX_PAUSE * */ @@ -2220,7 +2245,7 @@ static s32 e1000_config_fc_after_link_up(struct e1000_hw *hw) * * LOCAL DEVICE | LINK PARTNER * PAUSE | ASM_DIR | PAUSE | ASM_DIR | Result - *-------|---------|-------|---------|-------------------- + *-------|---------|-------|---------|------------------ * 1 | 1 | 0 | 1 | E1000_FC_RX_PAUSE * */ @@ -2233,25 +2258,27 @@ static s32 e1000_config_fc_after_link_up(struct e1000_hw *hw) e_dbg ("Flow Control = RX PAUSE frames only.\n"); } - /* Per the IEEE spec, at this point flow control should be - * disabled. However, we want to consider that we could - * be connected to a legacy switch that doesn't advertise - * desired flow control, but can be forced on the link - * partner. So if we advertised no flow control, that is - * what we will resolve to. If we advertised some kind of - * receive capability (Rx Pause Only or Full Flow Control) - * and the link partner advertised none, we will configure - * ourselves to enable Rx Flow Control only. We can do - * this safely for two reasons: If the link partner really - * didn't want flow control enabled, and we enable Rx, no - * harm done since we won't be receiving any PAUSE frames - * anyway. If the intent on the link partner was to have - * flow control enabled, then by us enabling RX only, we - * can at least receive pause frames and process them. - * This is a good idea because in most cases, since we are - * predominantly a server NIC, more times than not we will - * be asked to delay transmission of packets than asking - * our link partner to pause transmission of frames. + /* Per the IEEE spec, at this point flow control should + * be disabled. However, we want to consider that we + * could be connected to a legacy switch that doesn't + * advertise desired flow control, but can be forced on + * the link partner. So if we advertised no flow + * control, that is what we will resolve to. If we + * advertised some kind of receive capability (Rx Pause + * Only or Full Flow Control) and the link partner + * advertised none, we will configure ourselves to + * enable Rx Flow Control only. We can do this safely + * for two reasons: If the link partner really + * didn't want flow control enabled, and we enable Rx, + * no harm done since we won't be receiving any PAUSE + * frames anyway. If the intent on the link partner was + * to have flow control enabled, then by us enabling Rx + * only, we can at least receive pause frames and + * process them. This is a good idea because in most + * cases, since we are predominantly a server NIC, more + * times than not we will be asked to delay transmission + * of packets than asking our link partner to pause + * transmission of frames. */ else if ((hw->original_fc == E1000_FC_NONE || hw->original_fc == E1000_FC_TX_PAUSE) || @@ -2316,8 +2343,7 @@ static s32 e1000_check_for_serdes_link_generic(struct e1000_hw *hw) status = er32(STATUS); rxcw = er32(RXCW); - /* - * If we don't have link (auto-negotiation failed or link partner + /* If we don't have link (auto-negotiation failed or link partner * cannot auto-negotiate), and our link partner is not trying to * auto-negotiate with us (we are receiving idles or data), * we need to force link up. We also need to give auto-negotiation @@ -2346,8 +2372,7 @@ static s32 e1000_check_for_serdes_link_generic(struct e1000_hw *hw) goto out; } } else if ((ctrl & E1000_CTRL_SLU) && (rxcw & E1000_RXCW_C)) { - /* - * If we are forcing link and we are receiving /C/ ordered + /* If we are forcing link and we are receiving /C/ ordered * sets, re-enable auto-negotiation in the TXCW register * and disable forced link in the Device Control register * in an attempt to auto-negotiate with our link partner. @@ -2358,8 +2383,7 @@ static s32 e1000_check_for_serdes_link_generic(struct e1000_hw *hw) hw->serdes_has_link = true; } else if (!(E1000_TXCW_ANE & er32(TXCW))) { - /* - * If we force link for non-auto-negotiation switch, check + /* If we force link for non-auto-negotiation switch, check * link status based on MAC synchronization for internal * serdes media type. */ @@ -2468,15 +2492,17 @@ s32 e1000_check_for_link(struct e1000_hw *hw) if (phy_data & MII_SR_LINK_STATUS) { hw->get_link_status = false; - /* Check if there was DownShift, must be checked immediately after - * link-up */ + /* Check if there was DownShift, must be checked + * immediately after link-up + */ e1000_check_downshift(hw); /* If we are on 82544 or 82543 silicon and speed/duplex - * are forced to 10H or 10F, then we will implement the polarity - * reversal workaround. We disable interrupts first, and upon - * returning, place the devices interrupt state to its previous - * value except for the link status change interrupt which will + * are forced to 10H or 10F, then we will implement the + * polarity reversal workaround. We disable interrupts + * first, and upon returning, place the devices + * interrupt state to its previous value except for the + * link status change interrupt which will * happen due to the execution of this workaround. */ @@ -2527,9 +2553,10 @@ s32 e1000_check_for_link(struct e1000_hw *hw) } } - /* Configure Flow Control now that Auto-Neg has completed. First, we - * need to restore the desired flow control settings because we may - * have had to re-autoneg with a different link partner. + /* Configure Flow Control now that Auto-Neg has completed. + * First, we need to restore the desired flow control settings + * because we may have had to re-autoneg with a different link + * partner. */ ret_val = e1000_config_fc_after_link_up(hw); if (ret_val) { @@ -2538,11 +2565,12 @@ s32 e1000_check_for_link(struct e1000_hw *hw) } /* At this point we know that we are on copper and we have - * auto-negotiated link. These are conditions for checking the link - * partner capability register. We use the link speed to determine if - * TBI compatibility needs to be turned on or off. If the link is not - * at gigabit speed, then TBI compatibility is not needed. If we are - * at gigabit speed, we turn on TBI compatibility. + * auto-negotiated link. These are conditions for checking the + * link partner capability register. We use the link speed to + * determine if TBI compatibility needs to be turned on or off. + * If the link is not at gigabit speed, then TBI compatibility + * is not needed. If we are at gigabit speed, we turn on TBI + * compatibility. */ if (hw->tbi_compatibility_en) { u16 speed, duplex; @@ -2554,20 +2582,23 @@ s32 e1000_check_for_link(struct e1000_hw *hw) return ret_val; } if (speed != SPEED_1000) { - /* If link speed is not set to gigabit speed, we do not need - * to enable TBI compatibility. + /* If link speed is not set to gigabit speed, we + * do not need to enable TBI compatibility. */ if (hw->tbi_compatibility_on) { - /* If we previously were in the mode, turn it off. */ + /* If we previously were in the mode, + * turn it off. + */ rctl = er32(RCTL); rctl &= ~E1000_RCTL_SBP; ew32(RCTL, rctl); hw->tbi_compatibility_on = false; } } else { - /* If TBI compatibility is was previously off, turn it on. For - * compatibility with a TBI link partner, we will store bad - * packets. Some frames have an additional byte on the end and + /* If TBI compatibility is was previously off, + * turn it on. For compatibility with a TBI link + * partner, we will store bad packets. Some + * frames have an additional byte on the end and * will look like CRC errors to to the hardware. */ if (!hw->tbi_compatibility_on) { @@ -2629,9 +2660,9 @@ s32 e1000_get_speed_and_duplex(struct e1000_hw *hw, u16 *speed, u16 *duplex) *duplex = FULL_DUPLEX; } - /* IGP01 PHY may advertise full duplex operation after speed downgrade even - * if it is operating at half duplex. Here we set the duplex settings to - * match the duplex in the link partner's capabilities. + /* IGP01 PHY may advertise full duplex operation after speed downgrade + * even if it is operating at half duplex. Here we set the duplex + * settings to match the duplex in the link partner's capabilities. */ if (hw->phy_type == e1000_phy_igp && hw->speed_downgraded) { ret_val = e1000_read_phy_reg(hw, PHY_AUTONEG_EXP, &phy_data); @@ -2697,8 +2728,8 @@ static s32 e1000_wait_autoneg(struct e1000_hw *hw) */ static void e1000_raise_mdi_clk(struct e1000_hw *hw, u32 *ctrl) { - /* Raise the clock input to the Management Data Clock (by setting the MDC - * bit), and then delay 10 microseconds. + /* Raise the clock input to the Management Data Clock (by setting the + * MDC bit), and then delay 10 microseconds. */ ew32(CTRL, (*ctrl | E1000_CTRL_MDC)); E1000_WRITE_FLUSH(); @@ -2712,8 +2743,8 @@ static void e1000_raise_mdi_clk(struct e1000_hw *hw, u32 *ctrl) */ static void e1000_lower_mdi_clk(struct e1000_hw *hw, u32 *ctrl) { - /* Lower the clock input to the Management Data Clock (by clearing the MDC - * bit), and then delay 10 microseconds. + /* Lower the clock input to the Management Data Clock (by clearing the + * MDC bit), and then delay 10 microseconds. */ ew32(CTRL, (*ctrl & ~E1000_CTRL_MDC)); E1000_WRITE_FLUSH(); @@ -2746,10 +2777,10 @@ static void e1000_shift_out_mdi_bits(struct e1000_hw *hw, u32 data, u16 count) ctrl |= (E1000_CTRL_MDIO_DIR | E1000_CTRL_MDC_DIR); while (mask) { - /* A "1" is shifted out to the PHY by setting the MDIO bit to "1" and - * then raising and lowering the Management Data Clock. A "0" is - * shifted out to the PHY by setting the MDIO bit to "0" and then - * raising and lowering the clock. + /* A "1" is shifted out to the PHY by setting the MDIO bit to + * "1" and then raising and lowering the Management Data Clock. + * A "0" is shifted out to the PHY by setting the MDIO bit to + * "0" and then raising and lowering the clock. */ if (data & mask) ctrl |= E1000_CTRL_MDIO; @@ -2781,24 +2812,26 @@ static u16 e1000_shift_in_mdi_bits(struct e1000_hw *hw) u8 i; /* In order to read a register from the PHY, we need to shift in a total - * of 18 bits from the PHY. The first two bit (turnaround) times are used - * to avoid contention on the MDIO pin when a read operation is performed. - * These two bits are ignored by us and thrown away. Bits are "shifted in" - * by raising the input to the Management Data Clock (setting the MDC bit), - * and then reading the value of the MDIO bit. + * of 18 bits from the PHY. The first two bit (turnaround) times are + * used to avoid contention on the MDIO pin when a read operation is + * performed. These two bits are ignored by us and thrown away. Bits are + * "shifted in" by raising the input to the Management Data Clock + * (setting the MDC bit), and then reading the value of the MDIO bit. */ ctrl = er32(CTRL); - /* Clear MDIO_DIR (SWDPIO1) to indicate this bit is to be used as input. */ + /* Clear MDIO_DIR (SWDPIO1) to indicate this bit is to be used as + * input. + */ ctrl &= ~E1000_CTRL_MDIO_DIR; ctrl &= ~E1000_CTRL_MDIO; ew32(CTRL, ctrl); E1000_WRITE_FLUSH(); - /* Raise and Lower the clock before reading in the data. This accounts for - * the turnaround bits. The first clock occurred when we clocked out the - * last bit of the Register Address. + /* Raise and Lower the clock before reading in the data. This accounts + * for the turnaround bits. The first clock occurred when we clocked out + * the last bit of the Register Address. */ e1000_raise_mdi_clk(hw, &ctrl); e1000_lower_mdi_clk(hw, &ctrl); @@ -2870,8 +2903,8 @@ static s32 e1000_read_phy_reg_ex(struct e1000_hw *hw, u32 reg_addr, if (hw->mac_type > e1000_82543) { /* Set up Op-code, Phy Address, and register address in the MDI - * Control register. The MAC will take care of interfacing with the - * PHY to retrieve the desired data. + * Control register. The MAC will take care of interfacing with + * the PHY to retrieve the desired data. */ if (hw->mac_type == e1000_ce4100) { mdic = ((reg_addr << E1000_MDIC_REG_SHIFT) | @@ -2929,31 +2962,32 @@ static s32 e1000_read_phy_reg_ex(struct e1000_hw *hw, u32 reg_addr, *phy_data = (u16) mdic; } } else { - /* We must first send a preamble through the MDIO pin to signal the - * beginning of an MII instruction. This is done by sending 32 - * consecutive "1" bits. + /* We must first send a preamble through the MDIO pin to signal + * the beginning of an MII instruction. This is done by sending + * 32 consecutive "1" bits. */ e1000_shift_out_mdi_bits(hw, PHY_PREAMBLE, PHY_PREAMBLE_SIZE); /* Now combine the next few fields that are required for a read * operation. We use this method instead of calling the - * e1000_shift_out_mdi_bits routine five different times. The format of - * a MII read instruction consists of a shift out of 14 bits and is - * defined as follows: + * e1000_shift_out_mdi_bits routine five different times. The + * format of a MII read instruction consists of a shift out of + * 14 bits and is defined as follows: * <Preamble><SOF><Op Code><Phy Addr><Reg Addr> - * followed by a shift in of 18 bits. This first two bits shifted in - * are TurnAround bits used to avoid contention on the MDIO pin when a - * READ operation is performed. These two bits are thrown away - * followed by a shift in of 16 bits which contains the desired data. + * followed by a shift in of 18 bits. This first two bits + * shifted in are TurnAround bits used to avoid contention on + * the MDIO pin when a READ operation is performed. These two + * bits are thrown away followed by a shift in of 16 bits which + * contains the desired data. */ mdic = ((reg_addr) | (phy_addr << 5) | (PHY_OP_READ << 10) | (PHY_SOF << 12)); e1000_shift_out_mdi_bits(hw, mdic, 14); - /* Now that we've shifted out the read command to the MII, we need to - * "shift in" the 16-bit value (18 total bits) of the requested PHY - * register address. + /* Now that we've shifted out the read command to the MII, we + * need to "shift in" the 16-bit value (18 total bits) of the + * requested PHY register address. */ *phy_data = e1000_shift_in_mdi_bits(hw); } @@ -3060,18 +3094,18 @@ static s32 e1000_write_phy_reg_ex(struct e1000_hw *hw, u32 reg_addr, } } } else { - /* We'll need to use the SW defined pins to shift the write command - * out to the PHY. We first send a preamble to the PHY to signal the - * beginning of the MII instruction. This is done by sending 32 - * consecutive "1" bits. + /* We'll need to use the SW defined pins to shift the write + * command out to the PHY. We first send a preamble to the PHY + * to signal the beginning of the MII instruction. This is done + * by sending 32 consecutive "1" bits. */ e1000_shift_out_mdi_bits(hw, PHY_PREAMBLE, PHY_PREAMBLE_SIZE); - /* Now combine the remaining required fields that will indicate a - * write operation. We use this method instead of calling the - * e1000_shift_out_mdi_bits routine for each field in the command. The - * format of a MII write instruction is as follows: - * <Preamble><SOF><Op Code><Phy Addr><Reg Addr><Turnaround><Data>. + /* Now combine the remaining required fields that will indicate + * a write operation. We use this method instead of calling the + * e1000_shift_out_mdi_bits routine for each field in the + * command. The format of a MII write instruction is as follows: + * <Preamble><SOF><OpCode><PhyAddr><RegAddr><Turnaround><Data>. */ mdic = ((PHY_TURNAROUND) | (reg_addr << 2) | (phy_addr << 7) | (PHY_OP_WRITE << 12) | (PHY_SOF << 14)); @@ -3100,10 +3134,10 @@ s32 e1000_phy_hw_reset(struct e1000_hw *hw) e_dbg("Resetting Phy...\n"); if (hw->mac_type > e1000_82543) { - /* Read the device control register and assert the E1000_CTRL_PHY_RST - * bit. Then, take it out of reset. + /* Read the device control register and assert the + * E1000_CTRL_PHY_RST bit. Then, take it out of reset. * For e1000 hardware, we delay for 10ms between the assert - * and deassert. + * and de-assert. */ ctrl = er32(CTRL); ew32(CTRL, ctrl | E1000_CTRL_PHY_RST); @@ -3115,8 +3149,9 @@ s32 e1000_phy_hw_reset(struct e1000_hw *hw) E1000_WRITE_FLUSH(); } else { - /* Read the Extended Device Control Register, assert the PHY_RESET_DIR - * bit to put the PHY into reset. Then, take it out of reset. + /* Read the Extended Device Control Register, assert the + * PHY_RESET_DIR bit to put the PHY into reset. Then, take it + * out of reset. */ ctrl_ext = er32(CTRL_EXT); ctrl_ext |= E1000_CTRL_EXT_SDP4_DIR; @@ -3301,7 +3336,8 @@ static s32 e1000_phy_igp_get_info(struct e1000_hw *hw, e_dbg("e1000_phy_igp_get_info"); /* The downshift status is checked only once, after link is established, - * and it stored in the hw->speed_downgraded parameter. */ + * and it stored in the hw->speed_downgraded parameter. + */ phy_info->downshift = (e1000_downshift) hw->speed_downgraded; /* IGP01E1000 does not need to support it. */ @@ -3327,7 +3363,9 @@ static s32 e1000_phy_igp_get_info(struct e1000_hw *hw, if ((phy_data & IGP01E1000_PSSR_SPEED_MASK) == IGP01E1000_PSSR_SPEED_1000MBPS) { - /* Local/Remote Receiver Information are only valid at 1000 Mbps */ + /* Local/Remote Receiver Information are only valid @ 1000 + * Mbps + */ ret_val = e1000_read_phy_reg(hw, PHY_1000T_STATUS, &phy_data); if (ret_val) return ret_val; @@ -3379,7 +3417,8 @@ static s32 e1000_phy_m88_get_info(struct e1000_hw *hw, e_dbg("e1000_phy_m88_get_info"); /* The downshift status is checked only once, after link is established, - * and it stored in the hw->speed_downgraded parameter. */ + * and it stored in the hw->speed_downgraded parameter. + */ phy_info->downshift = (e1000_downshift) hw->speed_downgraded; ret_val = e1000_read_phy_reg(hw, M88E1000_PHY_SPEC_CTRL, &phy_data); @@ -3574,8 +3613,8 @@ s32 e1000_init_eeprom_params(struct e1000_hw *hw) } if (eeprom->type == e1000_eeprom_spi) { - /* eeprom_size will be an enum [0..8] that maps to eeprom sizes 128B to - * 32KB (incremented by powers of 2). + /* eeprom_size will be an enum [0..8] that maps to eeprom sizes + * 128B to 32KB (incremented by powers of 2). */ /* Set to default value for initial eeprom read. */ eeprom->word_size = 64; @@ -3585,8 +3624,9 @@ s32 e1000_init_eeprom_params(struct e1000_hw *hw) eeprom_size = (eeprom_size & EEPROM_SIZE_MASK) >> EEPROM_SIZE_SHIFT; /* 256B eeprom size was not supported in earlier hardware, so we - * bump eeprom_size up one to ensure that "1" (which maps to 256B) - * is never the result used in the shifting logic below. */ + * bump eeprom_size up one to ensure that "1" (which maps to + * 256B) is never the result used in the shifting logic below. + */ if (eeprom_size) eeprom_size++; @@ -3618,8 +3658,8 @@ static void e1000_raise_ee_clk(struct e1000_hw *hw, u32 *eecd) */ static void e1000_lower_ee_clk(struct e1000_hw *hw, u32 *eecd) { - /* Lower the clock input to the EEPROM (by clearing the SK bit), and then - * wait 50 microseconds. + /* Lower the clock input to the EEPROM (by clearing the SK bit), and + * then wait 50 microseconds. */ *eecd = *eecd & ~E1000_EECD_SK; ew32(EECD, *eecd); @@ -3651,10 +3691,11 @@ static void e1000_shift_out_ee_bits(struct e1000_hw *hw, u16 data, u16 count) eecd |= E1000_EECD_DO; } do { - /* A "1" is shifted out to the EEPROM by setting bit "DI" to a "1", - * and then raising and then lowering the clock (the SK bit controls - * the clock input to the EEPROM). A "0" is shifted out to the EEPROM - * by setting "DI" to "0" and then raising and then lowering the clock. + /* A "1" is shifted out to the EEPROM by setting bit "DI" to a + * "1", and then raising and then lowering the clock (the SK bit + * controls the clock input to the EEPROM). A "0" is shifted + * out to the EEPROM by setting "DI" to "0" and then raising and + * then lowering the clock. */ eecd &= ~E1000_EECD_DI; @@ -3691,9 +3732,9 @@ static u16 e1000_shift_in_ee_bits(struct e1000_hw *hw, u16 count) /* In order to read a register from the EEPROM, we need to shift 'count' * bits in from the EEPROM. Bits are "shifted in" by raising the clock - * input to the EEPROM (setting the SK bit), and then reading the value of - * the "DO" bit. During this "shifting in" process the "DI" bit should - * always be clear. + * input to the EEPROM (setting the SK bit), and then reading the value + * of the "DO" bit. During this "shifting in" process the "DI" bit + * should always be clear. */ eecd = er32(EECD); @@ -3945,8 +3986,8 @@ static s32 e1000_do_read_eeprom(struct e1000_hw *hw, u16 offset, u16 words, if (eeprom->word_size == 0) e1000_init_eeprom_params(hw); - /* A check for invalid values: offset too large, too many words, and not - * enough words. + /* A check for invalid values: offset too large, too many words, and + * not enough words. */ if ((offset >= eeprom->word_size) || (words > eeprom->word_size - offset) || (words == 0)) { @@ -3964,7 +4005,8 @@ static s32 e1000_do_read_eeprom(struct e1000_hw *hw, u16 offset, u16 words, return -E1000_ERR_EEPROM; /* Set up the SPI or Microwire EEPROM for bit-bang reading. We have - * acquired the EEPROM at this point, so any returns should release it */ + * acquired the EEPROM at this point, so any returns should release it + */ if (eeprom->type == e1000_eeprom_spi) { u16 word_in; u8 read_opcode = EEPROM_READ_OPCODE_SPI; @@ -3976,7 +4018,9 @@ static s32 e1000_do_read_eeprom(struct e1000_hw *hw, u16 offset, u16 words, e1000_standby_eeprom(hw); - /* Some SPI eeproms use the 8th address bit embedded in the opcode */ + /* Some SPI eeproms use the 8th address bit embedded in the + * opcode + */ if ((eeprom->address_bits == 8) && (offset >= 128)) read_opcode |= EEPROM_A8_OPCODE_SPI; @@ -3985,11 +4029,13 @@ static s32 e1000_do_read_eeprom(struct e1000_hw *hw, u16 offset, u16 words, e1000_shift_out_ee_bits(hw, (u16) (offset * 2), eeprom->address_bits); - /* Read the data. The address of the eeprom internally increments with - * each byte (spi) being read, saving on the overhead of eeprom setup - * and tear-down. The address counter will roll over if reading beyond - * the size of the eeprom, thus allowing the entire memory to be read - * starting from any offset. */ + /* Read the data. The address of the eeprom internally + * increments with each byte (spi) being read, saving on the + * overhead of eeprom setup and tear-down. The address counter + * will roll over if reading beyond the size of the eeprom, thus + * allowing the entire memory to be read starting from any + * offset. + */ for (i = 0; i < words; i++) { word_in = e1000_shift_in_ee_bits(hw, 16); data[i] = (word_in >> 8) | (word_in << 8); @@ -4003,8 +4049,9 @@ static s32 e1000_do_read_eeprom(struct e1000_hw *hw, u16 offset, u16 words, e1000_shift_out_ee_bits(hw, (u16) (offset + i), eeprom->address_bits); - /* Read the data. For microwire, each word requires the overhead - * of eeprom setup and tear-down. */ + /* Read the data. For microwire, each word requires the + * overhead of eeprom setup and tear-down. + */ data[i] = e1000_shift_in_ee_bits(hw, 16); e1000_standby_eeprom(hw); } @@ -4119,8 +4166,8 @@ static s32 e1000_do_write_eeprom(struct e1000_hw *hw, u16 offset, u16 words, if (eeprom->word_size == 0) e1000_init_eeprom_params(hw); - /* A check for invalid values: offset too large, too many words, and not - * enough words. + /* A check for invalid values: offset too large, too many words, and + * not enough words. */ if ((offset >= eeprom->word_size) || (words > eeprom->word_size - offset) || (words == 0)) { @@ -4174,7 +4221,9 @@ static s32 e1000_write_eeprom_spi(struct e1000_hw *hw, u16 offset, u16 words, e1000_standby_eeprom(hw); - /* Some SPI eeproms use the 8th address bit embedded in the opcode */ + /* Some SPI eeproms use the 8th address bit embedded in the + * opcode + */ if ((eeprom->address_bits == 8) && (offset >= 128)) write_opcode |= EEPROM_A8_OPCODE_SPI; @@ -4186,16 +4235,19 @@ static s32 e1000_write_eeprom_spi(struct e1000_hw *hw, u16 offset, u16 words, /* Send the data */ - /* Loop to allow for up to whole page write (32 bytes) of eeprom */ + /* Loop to allow for up to whole page write (32 bytes) of + * eeprom + */ while (widx < words) { u16 word_out = data[widx]; word_out = (word_out >> 8) | (word_out << 8); e1000_shift_out_ee_bits(hw, word_out, 16); widx++; - /* Some larger eeprom sizes are capable of a 32-byte PAGE WRITE - * operation, while the smaller eeproms are capable of an 8-byte - * PAGE WRITE operation. Break the inner loop to pass new address + /* Some larger eeprom sizes are capable of a 32-byte + * PAGE WRITE operation, while the smaller eeproms are + * capable of an 8-byte PAGE WRITE operation. Break the + * inner loop to pass new address */ if ((((offset + widx) * 2) % eeprom->page_size) == 0) { e1000_standby_eeprom(hw); @@ -4249,14 +4301,15 @@ static s32 e1000_write_eeprom_microwire(struct e1000_hw *hw, u16 offset, /* Send the data */ e1000_shift_out_ee_bits(hw, data[words_written], 16); - /* Toggle the CS line. This in effect tells the EEPROM to execute - * the previous command. + /* Toggle the CS line. This in effect tells the EEPROM to + * execute the previous command. */ e1000_standby_eeprom(hw); - /* Read DO repeatedly until it is high (equal to '1'). The EEPROM will - * signal that the command has been completed by raising the DO signal. - * If DO does not go high in 10 milliseconds, then error out. + /* Read DO repeatedly until it is high (equal to '1'). The + * EEPROM will signal that the command has been completed by + * raising the DO signal. If DO does not go high in 10 + * milliseconds, then error out. */ for (i = 0; i < 200; i++) { eecd = er32(EECD); @@ -4483,7 +4536,8 @@ static void e1000_clear_vfta(struct e1000_hw *hw) for (offset = 0; offset < E1000_VLAN_FILTER_TBL_SIZE; offset++) { /* If the offset we want to clear is the same offset of the * manageability VLAN ID, then clear all bits except that of the - * manageability unit */ + * manageability unit + */ vfta_value = (offset == vfta_offset) ? vfta_bit_in_reg : 0; E1000_WRITE_REG_ARRAY(hw, VFTA, offset, vfta_value); E1000_WRITE_FLUSH(); @@ -4911,12 +4965,12 @@ void e1000_tbi_adjust_stats(struct e1000_hw *hw, struct e1000_hw_stats *stats, * counters overcount this packet as a CRC error and undercount * the packet as a good packet */ - /* This packet should not be counted as a CRC error. */ + /* This packet should not be counted as a CRC error. */ stats->crcerrs--; - /* This packet does count as a Good Packet Received. */ + /* This packet does count as a Good Packet Received. */ stats->gprc++; - /* Adjust the Good Octets received counters */ + /* Adjust the Good Octets received counters */ carry_bit = 0x80000000 & stats->gorcl; stats->gorcl += frame_len; /* If the high bit of Gorcl (the low 32 bits of the Good Octets @@ -5196,8 +5250,9 @@ static s32 e1000_check_polarity(struct e1000_hw *hw, if (ret_val) return ret_val; - /* If speed is 1000 Mbps, must read the IGP01E1000_PHY_PCS_INIT_REG to - * find the polarity status */ + /* If speed is 1000 Mbps, must read the + * IGP01E1000_PHY_PCS_INIT_REG to find the polarity status + */ if ((phy_data & IGP01E1000_PSSR_SPEED_MASK) == IGP01E1000_PSSR_SPEED_1000MBPS) { @@ -5213,8 +5268,9 @@ static s32 e1000_check_polarity(struct e1000_hw *hw, e1000_rev_polarity_reversed : e1000_rev_polarity_normal; } else { - /* For 10 Mbps, read the polarity bit in the status register. (for - * 100 Mbps this bit is always 0) */ + /* For 10 Mbps, read the polarity bit in the status + * register. (for 100 Mbps this bit is always 0) + */ *polarity = (phy_data & IGP01E1000_PSSR_POLARITY_REVERSED) ? e1000_rev_polarity_reversed : @@ -5374,8 +5430,9 @@ static s32 e1000_config_dsp_after_link_change(struct e1000_hw *hw, bool link_up) } } else { if (hw->dsp_config_state == e1000_dsp_config_activated) { - /* Save off the current value of register 0x2F5B to be restored at - * the end of the routines. */ + /* Save off the current value of register 0x2F5B to be + * restored at the end of the routines. + */ ret_val = e1000_read_phy_reg(hw, 0x2F5B, &phy_saved_data); @@ -5391,7 +5448,7 @@ static s32 e1000_config_dsp_after_link_change(struct e1000_hw *hw, bool link_up) msleep(20); ret_val = e1000_write_phy_reg(hw, 0x0000, - IGP01E1000_IEEE_FORCE_GIGA); + IGP01E1000_IEEE_FORCE_GIGA); if (ret_val) return ret_val; for (i = 0; i < IGP01E1000_PHY_CHANNEL_NUM; i++) { @@ -5412,7 +5469,7 @@ static s32 e1000_config_dsp_after_link_change(struct e1000_hw *hw, bool link_up) } ret_val = e1000_write_phy_reg(hw, 0x0000, - IGP01E1000_IEEE_RESTART_AUTONEG); + IGP01E1000_IEEE_RESTART_AUTONEG); if (ret_val) return ret_val; @@ -5429,8 +5486,9 @@ static s32 e1000_config_dsp_after_link_change(struct e1000_hw *hw, bool link_up) } if (hw->ffe_config_state == e1000_ffe_config_active) { - /* Save off the current value of register 0x2F5B to be restored at - * the end of the routines. */ + /* Save off the current value of register 0x2F5B to be + * restored at the end of the routines. + */ ret_val = e1000_read_phy_reg(hw, 0x2F5B, &phy_saved_data); @@ -5446,7 +5504,7 @@ static s32 e1000_config_dsp_after_link_change(struct e1000_hw *hw, bool link_up) msleep(20); ret_val = e1000_write_phy_reg(hw, 0x0000, - IGP01E1000_IEEE_FORCE_GIGA); + IGP01E1000_IEEE_FORCE_GIGA); if (ret_val) return ret_val; ret_val = @@ -5456,7 +5514,7 @@ static s32 e1000_config_dsp_after_link_change(struct e1000_hw *hw, bool link_up) return ret_val; ret_val = e1000_write_phy_reg(hw, 0x0000, - IGP01E1000_IEEE_RESTART_AUTONEG); + IGP01E1000_IEEE_RESTART_AUTONEG); if (ret_val) return ret_val; @@ -5542,8 +5600,9 @@ static s32 e1000_set_d3_lplu_state(struct e1000_hw *hw, bool active) return E1000_SUCCESS; /* During driver activity LPLU should not be used or it will attain link - * from the lowest speeds starting from 10Mbps. The capability is used for - * Dx transitions and states */ + * from the lowest speeds starting from 10Mbps. The capability is used + * for Dx transitions and states + */ if (hw->mac_type == e1000_82541_rev_2 || hw->mac_type == e1000_82547_rev_2) { ret_val = @@ -5563,10 +5622,11 @@ static s32 e1000_set_d3_lplu_state(struct e1000_hw *hw, bool active) return ret_val; } - /* LPLU and SmartSpeed are mutually exclusive. LPLU is used during - * Dx states where the power conservation is most important. During - * driver activity we should enable SmartSpeed, so performance is - * maintained. */ + /* LPLU and SmartSpeed are mutually exclusive. LPLU is used + * during Dx states where the power conservation is most + * important. During driver activity we should enable + * SmartSpeed, so performance is maintained. + */ if (hw->smart_speed == e1000_smart_speed_on) { ret_val = e1000_read_phy_reg(hw, IGP01E1000_PHY_PORT_CONFIG, |