diff options
Diffstat (limited to 'drivers/net/can/Kconfig')
| -rw-r--r-- | drivers/net/can/Kconfig | 66 |
1 files changed, 30 insertions, 36 deletions
diff --git a/drivers/net/can/Kconfig b/drivers/net/can/Kconfig index 6d04183ed955..0d40aef928e2 100644 --- a/drivers/net/can/Kconfig +++ b/drivers/net/can/Kconfig @@ -70,13 +70,6 @@ config CAN_AT91 This is a driver for the SoC CAN controller in Atmel's AT91SAM9263 and AT91SAM9X5 processors. -config CAN_TI_HECC - depends on ARM - tristate "TI High End CAN Controller" - ---help--- - Driver for TI HECC (High End CAN Controller) module found on many - TI devices. The device specifications are available from www.ti.com - config CAN_BFIN depends on BF534 || BF536 || BF537 || BF538 || BF539 || BF54x tristate "Analog Devices Blackfin on-chip CAN" @@ -86,30 +79,12 @@ config CAN_BFIN To compile this driver as a module, choose M here: the module will be called bfin_can. -config CAN_JANZ_ICAN3 - tristate "Janz VMOD-ICAN3 Intelligent CAN controller" - depends on MFD_JANZ_CMODIO - ---help--- - Driver for Janz VMOD-ICAN3 Intelligent CAN controller module, which - connects to a MODULbus carrier board. - - This driver can also be built as a module. If so, the module will be - called janz-ican3.ko. - config CAN_FLEXCAN tristate "Support for Freescale FLEXCAN based chips" depends on ARM || PPC ---help--- Say Y here if you want to support for Freescale FlexCAN. -config PCH_CAN - tristate "Intel EG20T PCH CAN controller" - depends on PCI && (X86_32 || COMPILE_TEST) - ---help--- - This driver is for PCH CAN of Topcliff (Intel EG20T PCH) which - is an IOH for x86 embedded processor (Intel Atom E6xx series). - This driver can access CAN bus. - config CAN_GRCAN tristate "Aeroflex Gaisler GRCAN and GRHCAN CAN devices" depends on OF && HAS_DMA @@ -119,9 +94,19 @@ config CAN_GRCAN endian syntheses of the cores would need some modifications on the hardware level to work. +config CAN_JANZ_ICAN3 + tristate "Janz VMOD-ICAN3 Intelligent CAN controller" + depends on MFD_JANZ_CMODIO + ---help--- + Driver for Janz VMOD-ICAN3 Intelligent CAN controller module, which + connects to a MODULbus carrier board. + + This driver can also be built as a module. If so, the module will be + called janz-ican3.ko. + config CAN_RCAR tristate "Renesas R-Car CAN controller" - depends on ARM + depends on ARCH_RENESAS || ARM ---help--- Say Y here if you want to use CAN controller found on Renesas R-Car SoCs. @@ -139,6 +124,13 @@ config CAN_SUN4I To compile this driver as a module, choose M here: the module will be called sun4i_can. +config CAN_TI_HECC + depends on ARM + tristate "TI High End CAN Controller" + ---help--- + Driver for TI HECC (High End CAN Controller) module found on many + TI devices. The device specifications are available from www.ti.com + config CAN_XILINXCAN tristate "Xilinx CAN" depends on ARCH_ZYNQ || ARM64 || MICROBLAZE || COMPILE_TEST @@ -147,22 +139,24 @@ config CAN_XILINXCAN Xilinx CAN driver. This driver supports both soft AXI CAN IP and Zynq CANPS IP. -source "drivers/net/can/mscan/Kconfig" - -source "drivers/net/can/sja1000/Kconfig" +config PCH_CAN + tristate "Intel EG20T PCH CAN controller" + depends on PCI && (X86_32 || COMPILE_TEST) + ---help--- + This driver is for PCH CAN of Topcliff (Intel EG20T PCH) which + is an IOH for x86 embedded processor (Intel Atom E6xx series). + This driver can access CAN bus. source "drivers/net/can/c_can/Kconfig" - -source "drivers/net/can/m_can/Kconfig" - source "drivers/net/can/cc770/Kconfig" - +source "drivers/net/can/ifi_canfd/Kconfig" +source "drivers/net/can/m_can/Kconfig" +source "drivers/net/can/mscan/Kconfig" +source "drivers/net/can/sja1000/Kconfig" +source "drivers/net/can/softing/Kconfig" source "drivers/net/can/spi/Kconfig" - source "drivers/net/can/usb/Kconfig" -source "drivers/net/can/softing/Kconfig" - endif config CAN_DEBUG_DEVICES |