9 files changed, 90 insertions, 107 deletions

diff --git a/drivers/mmc/host/Kconfig b/drivers/mmc/host/Kconfig
index f0cb7aeabbc4..31481c9fcc2e 100644
--- a/drivers/mmc/host/Kconfig
+++ b/drivers/mmc/host/Kconfig
@@ -302,7 +302,7 @@ config MMC_SDHCI_TEGRA
 config MMC_SDHCI_S3C
 	tristate "SDHCI support on Samsung S3C SoC"
 	depends on MMC_SDHCI
-	depends on PLAT_SAMSUNG || COMPILE_TEST
+	depends on PLAT_SAMSUNG || ARCH_S5PV210 || ARCH_EXYNOS || COMPILE_TEST
 	help
 	  This selects the Secure Digital Host Controller Interface (SDHCI)
 	  often referrered to as the HSMMC block in some of the Samsung S3C
diff --git a/drivers/mmc/host/renesas_sdhi_core.c b/drivers/mmc/host/renesas_sdhi_core.c
index 414314151d0a..acb9c81a4e45 100644
--- a/drivers/mmc/host/renesas_sdhi_core.c
+++ b/drivers/mmc/host/renesas_sdhi_core.c
@@ -572,17 +572,6 @@ static void renesas_sdhi_reset(struct tmio_mmc_host *host)
 					     TMIO_MASK_INIT_RCAR2);
 }
 
-/*
- * This is a temporary workaround! This driver used 'hw_reset' wrongly and the
- * fix for that showed a regression. So, we mimic the old behaviour until the
- * proper solution is found.
- */
-static void renesas_sdhi_hw_reset(struct mmc_host *mmc)
-{
-	struct tmio_mmc_host *host = mmc_priv(mmc);
-	renesas_sdhi_reset(host);
-}
-
 #define SH_MOBILE_SDHI_MIN_TAP_ROW 3
 
 static int renesas_sdhi_select_tuning(struct tmio_mmc_host *host)
@@ -1020,8 +1009,6 @@ int renesas_sdhi_probe(struct platform_device *pdev,
 		if (of_data && of_data->scc_offset) {
 			priv->scc_ctl = host->ctl + of_data->scc_offset;
 			host->reset = renesas_sdhi_reset;
-			host->ops.hw_reset = renesas_sdhi_hw_reset;
-			host->mmc->caps |= MMC_CAP_HW_RESET;
 		}
 	}
 
@@ -1160,6 +1147,7 @@ int renesas_sdhi_remove(struct platform_device *pdev)
 
 	tmio_mmc_host_remove(host);
 	renesas_sdhi_clk_disable(host);
+	tmio_mmc_host_free(host);
 
 	return 0;
 }
diff --git a/drivers/mmc/host/s3cmci.c b/drivers/mmc/host/s3cmci.c
index e3698aba8dd3..643d54eceef6 100644
--- a/drivers/mmc/host/s3cmci.c
+++ b/drivers/mmc/host/s3cmci.c
@@ -24,11 +24,6 @@
 #include <linux/of.h>
 #include <linux/of_device.h>
 #include <linux/mmc/slot-gpio.h>
-
-#include <plat/gpio-cfg.h>
-#include <mach/dma.h>
-#include <mach/gpio-samsung.h>
-
 #include <linux/platform_data/mmc-s3cmci.h>
 
 #include "s3cmci.h"
@@ -305,7 +300,8 @@ static inline void clear_imask(struct s3cmci_host *host)
 static void s3cmci_check_sdio_irq(struct s3cmci_host *host)
 {
 	if (host->sdio_irqen) {
-		if (gpio_get_value(S3C2410_GPE(8)) == 0) {
+		if (host->pdata->bus[3] &&
+		    gpiod_get_value(host->pdata->bus[3]) == 0) {
 			pr_debug("%s: signalling irq\n", __func__);
 			mmc_signal_sdio_irq(host->mmc);
 		}
@@ -1201,33 +1197,20 @@ static void s3cmci_set_ios(struct mmc_host *mmc, struct mmc_ios *ios)
 	switch (ios->power_mode) {
 	case MMC_POWER_ON:
 	case MMC_POWER_UP:
-		/* Configure GPE5...GPE10 pins in SD mode */
-		if (!host->pdev->dev.of_node)
-			s3c_gpio_cfgall_range(S3C2410_GPE(5), 6, S3C_GPIO_SFN(2),
-					      S3C_GPIO_PULL_NONE);
-
-		if (host->pdata->set_power)
-			host->pdata->set_power(ios->power_mode, ios->vdd);
-
 		if (!host->is2440)
 			mci_con |= S3C2410_SDICON_FIFORESET;
-
 		break;
 
 	case MMC_POWER_OFF:
 	default:
-		if (!host->pdev->dev.of_node)
-			gpio_direction_output(S3C2410_GPE(5), 0);
-
 		if (host->is2440)
 			mci_con |= S3C2440_SDICON_SDRESET;
-
-		if (host->pdata->set_power)
-			host->pdata->set_power(ios->power_mode, ios->vdd);
-
 		break;
 	}
 
+	if (host->pdata->set_power)
+		host->pdata->set_power(ios->power_mode, ios->vdd);
+
 	s3cmci_set_clk(host, ios);
 
 	/* Set CLOCK_ENABLE */
@@ -1305,13 +1288,6 @@ static const struct mmc_host_ops s3cmci_ops = {
 	.enable_sdio_irq = s3cmci_enable_sdio_irq,
 };
 
-static struct s3c24xx_mci_pdata s3cmci_def_pdata = {
-	/* This is currently here to avoid a number of if (host->pdata)
-	 * checks. Any zero fields to ensure reasonable defaults are picked. */
-	 .no_wprotect = 1,
-	 .no_detect = 1,
-};
-
 #ifdef CONFIG_ARM_S3C24XX_CPUFREQ
 
 static int s3cmci_cpufreq_transition(struct notifier_block *nb,
@@ -1465,24 +1441,21 @@ static int s3cmci_probe_pdata(struct s3cmci_host *host)
 	int i, ret;
 
 	host->is2440 = platform_get_device_id(pdev)->driver_data;
+	pdata = pdev->dev.platform_data;
+	if (!pdata) {
+		dev_err(&pdev->dev, "need platform data");
+		return -ENXIO;
+	}
 
-	for (i = S3C2410_GPE(5); i <= S3C2410_GPE(10); i++) {
-		ret = gpio_request(i, dev_name(&pdev->dev));
-		if (ret) {
+	for (i = 0; i < 6; i++) {
+		pdata->bus[i] = devm_gpiod_get_index(&pdev->dev, "bus", i,
+						     GPIOD_OUT_LOW);
+		if (IS_ERR(pdata->bus[i])) {
 			dev_err(&pdev->dev, "failed to get gpio %d\n", i);
-
-			for (i--; i >= S3C2410_GPE(5); i--)
-				gpio_free(i);
-
-			return ret;
+			return PTR_ERR(pdata->bus[i]);
 		}
 	}
 
-	if (!pdev->dev.platform_data)
-		pdev->dev.platform_data = &s3cmci_def_pdata;
-
-	pdata = pdev->dev.platform_data;
-
 	if (pdata->no_wprotect)
 		mmc->caps2 |= MMC_CAP2_NO_WRITE_PROTECT;
 
@@ -1537,7 +1510,6 @@ static int s3cmci_probe(struct platform_device *pdev)
 	struct s3cmci_host *host;
 	struct mmc_host	*mmc;
 	int ret;
-	int i;
 
 	mmc = mmc_alloc_host(sizeof(struct s3cmci_host), &pdev->dev);
 	if (!mmc) {
@@ -1581,7 +1553,7 @@ static int s3cmci_probe(struct platform_device *pdev)
 			"failed to get io memory region resource.\n");
 
 		ret = -ENOENT;
-		goto probe_free_gpio;
+		goto probe_free_host;
 	}
 
 	host->mem = request_mem_region(host->mem->start,
@@ -1590,7 +1562,7 @@ static int s3cmci_probe(struct platform_device *pdev)
 	if (!host->mem) {
 		dev_err(&pdev->dev, "failed to request io memory region.\n");
 		ret = -ENOENT;
-		goto probe_free_gpio;
+		goto probe_free_host;
 	}
 
 	host->base = ioremap(host->mem->start, resource_size(host->mem));
@@ -1714,11 +1686,6 @@ static int s3cmci_probe(struct platform_device *pdev)
  probe_free_mem_region:
 	release_mem_region(host->mem->start, resource_size(host->mem));
 
- probe_free_gpio:
-	if (!pdev->dev.of_node)
-		for (i = S3C2410_GPE(5); i <= S3C2410_GPE(10); i++)
-			gpio_free(i);
-
  probe_free_host:
 	mmc_free_host(mmc);
 
@@ -1744,7 +1711,6 @@ static int s3cmci_remove(struct platform_device *pdev)
 {
 	struct mmc_host		*mmc  = platform_get_drvdata(pdev);
 	struct s3cmci_host	*host = mmc_priv(mmc);
-	int i;
 
 	s3cmci_shutdown(pdev);
 
@@ -1757,10 +1723,6 @@ static int s3cmci_remove(struct platform_device *pdev)
 
 	free_irq(host->irq, host);
 
-	if (!pdev->dev.of_node)
-		for (i = S3C2410_GPE(5); i <= S3C2410_GPE(10); i++)
-			gpio_free(i);
-
 	iounmap(host->base);
 	release_mem_region(host->mem->start, resource_size(host->mem));
 
diff --git a/drivers/mmc/host/sdhci-esdhc.h b/drivers/mmc/host/sdhci-esdhc.h
index a30796e79b1c..6de02f09c322 100644
--- a/drivers/mmc/host/sdhci-esdhc.h
+++ b/drivers/mmc/host/sdhci-esdhc.h
@@ -5,6 +5,7 @@
  * Copyright (c) 2007 Freescale Semiconductor, Inc.
  * Copyright (c) 2009 MontaVista Software, Inc.
  * Copyright (c) 2010 Pengutronix e.K.
+ * Copyright 2020 NXP
  *   Author: Wolfram Sang <kernel@pengutronix.de>
  */
 
@@ -88,6 +89,7 @@
 /* DLL Config 0 Register */
 #define ESDHC_DLLCFG0			0x160
 #define ESDHC_DLL_ENABLE		0x80000000
+#define ESDHC_DLL_RESET			0x40000000
 #define ESDHC_DLL_FREQ_SEL		0x08000000
 
 /* DLL Config 1 Register */
diff --git a/drivers/mmc/host/sdhci-of-arasan.c b/drivers/mmc/host/sdhci-of-arasan.c
index 829ccef87426..d25a4b50c2f3 100644
--- a/drivers/mmc/host/sdhci-of-arasan.c
+++ b/drivers/mmc/host/sdhci-of-arasan.c
@@ -30,7 +30,10 @@
 #define SDHCI_ARASAN_VENDOR_REGISTER	0x78
 
 #define SDHCI_ARASAN_ITAPDLY_REGISTER	0xF0F8
+#define SDHCI_ARASAN_ITAPDLY_SEL_MASK	0xFF
+
 #define SDHCI_ARASAN_OTAPDLY_REGISTER	0xF0FC
+#define SDHCI_ARASAN_OTAPDLY_SEL_MASK	0x3F
 
 #define SDHCI_ARASAN_CQE_BASE_ADDR	0x200
 #define VENDOR_ENHANCED_STROBE		BIT(0)
@@ -600,14 +603,8 @@ static int sdhci_zynqmp_sdcardclk_set_phase(struct clk_hw *hw, int degrees)
 	u8 tap_delay, tap_max = 0;
 	int ret;
 
-	/*
-	 * This is applicable for SDHCI_SPEC_300 and above
-	 * ZynqMP does not set phase for <=25MHz clock.
-	 * If degrees is zero, no need to do anything.
-	 */
-	if (host->version < SDHCI_SPEC_300 ||
-	    host->timing == MMC_TIMING_LEGACY ||
-	    host->timing == MMC_TIMING_UHS_SDR12 || !degrees)
+	/* This is applicable for SDHCI_SPEC_300 and above */
+	if (host->version < SDHCI_SPEC_300)
 		return 0;
 
 	switch (host->timing) {
@@ -638,6 +635,9 @@ static int sdhci_zynqmp_sdcardclk_set_phase(struct clk_hw *hw, int degrees)
 	if (ret)
 		pr_err("Error setting Output Tap Delay\n");
 
+	/* Release DLL Reset */
+	zynqmp_pm_sd_dll_reset(node_id, PM_DLL_RESET_RELEASE);
+
 	return ret;
 }
 
@@ -668,16 +668,13 @@ static int sdhci_zynqmp_sampleclk_set_phase(struct clk_hw *hw, int degrees)
 	u8 tap_delay, tap_max = 0;
 	int ret;
 
-	/*
-	 * This is applicable for SDHCI_SPEC_300 and above
-	 * ZynqMP does not set phase for <=25MHz clock.
-	 * If degrees is zero, no need to do anything.
-	 */
-	if (host->version < SDHCI_SPEC_300 ||
-	    host->timing == MMC_TIMING_LEGACY ||
-	    host->timing == MMC_TIMING_UHS_SDR12 || !degrees)
+	/* This is applicable for SDHCI_SPEC_300 and above */
+	if (host->version < SDHCI_SPEC_300)
 		return 0;
 
+	/* Assert DLL Reset */
+	zynqmp_pm_sd_dll_reset(node_id, PM_DLL_RESET_ASSERT);
+
 	switch (host->timing) {
 	case MMC_TIMING_MMC_HS:
 	case MMC_TIMING_SD_HS:
@@ -733,14 +730,8 @@ static int sdhci_versal_sdcardclk_set_phase(struct clk_hw *hw, int degrees)
 	struct sdhci_host *host = sdhci_arasan->host;
 	u8 tap_delay, tap_max = 0;
 
-	/*
-	 * This is applicable for SDHCI_SPEC_300 and above
-	 * Versal does not set phase for <=25MHz clock.
-	 * If degrees is zero, no need to do anything.
-	 */
-	if (host->version < SDHCI_SPEC_300 ||
-	    host->timing == MMC_TIMING_LEGACY ||
-	    host->timing == MMC_TIMING_UHS_SDR12 || !degrees)
+	/* This is applicable for SDHCI_SPEC_300 and above */
+	if (host->version < SDHCI_SPEC_300)
 		return 0;
 
 	switch (host->timing) {
@@ -773,6 +764,7 @@ static int sdhci_versal_sdcardclk_set_phase(struct clk_hw *hw, int degrees)
 		regval = sdhci_readl(host, SDHCI_ARASAN_OTAPDLY_REGISTER);
 		regval |= SDHCI_OTAPDLY_ENABLE;
 		sdhci_writel(host, regval, SDHCI_ARASAN_OTAPDLY_REGISTER);
+		regval &= ~SDHCI_ARASAN_OTAPDLY_SEL_MASK;
 		regval |= tap_delay;
 		sdhci_writel(host, regval, SDHCI_ARASAN_OTAPDLY_REGISTER);
 	}
@@ -804,14 +796,8 @@ static int sdhci_versal_sampleclk_set_phase(struct clk_hw *hw, int degrees)
 	struct sdhci_host *host = sdhci_arasan->host;
 	u8 tap_delay, tap_max = 0;
 
-	/*
-	 * This is applicable for SDHCI_SPEC_300 and above
-	 * Versal does not set phase for <=25MHz clock.
-	 * If degrees is zero, no need to do anything.
-	 */
-	if (host->version < SDHCI_SPEC_300 ||
-	    host->timing == MMC_TIMING_LEGACY ||
-	    host->timing == MMC_TIMING_UHS_SDR12 || !degrees)
+	/* This is applicable for SDHCI_SPEC_300 and above */
+	if (host->version < SDHCI_SPEC_300)
 		return 0;
 
 	switch (host->timing) {
@@ -846,6 +832,7 @@ static int sdhci_versal_sampleclk_set_phase(struct clk_hw *hw, int degrees)
 		sdhci_writel(host, regval, SDHCI_ARASAN_ITAPDLY_REGISTER);
 		regval |= SDHCI_ITAPDLY_ENABLE;
 		sdhci_writel(host, regval, SDHCI_ARASAN_ITAPDLY_REGISTER);
+		regval &= ~SDHCI_ARASAN_ITAPDLY_SEL_MASK;
 		regval |= tap_delay;
 		sdhci_writel(host, regval, SDHCI_ARASAN_ITAPDLY_REGISTER);
 		regval &= ~SDHCI_ITAPDLY_CHGWIN;
diff --git a/drivers/mmc/host/sdhci-of-esdhc.c b/drivers/mmc/host/sdhci-of-esdhc.c
index 0b45eff6fed4..ab5ab969f711 100644
--- a/drivers/mmc/host/sdhci-of-esdhc.c
+++ b/drivers/mmc/host/sdhci-of-esdhc.c
@@ -4,6 +4,7 @@
  *
  * Copyright (c) 2007, 2010, 2012 Freescale Semiconductor, Inc.
  * Copyright (c) 2009 MontaVista Software, Inc.
+ * Copyright 2020 NXP
  *
  * Authors: Xiaobo Xie <X.Xie@freescale.com>
  *	    Anton Vorontsov <avorontsov@ru.mvista.com>
@@ -19,6 +20,7 @@
 #include <linux/clk.h>
 #include <linux/ktime.h>
 #include <linux/dma-mapping.h>
+#include <linux/iopoll.h>
 #include <linux/mmc/host.h>
 #include <linux/mmc/mmc.h>
 #include "sdhci-pltfm.h"
@@ -743,6 +745,21 @@ static void esdhc_of_set_clock(struct sdhci_host *host, unsigned int clock)
 		if (host->mmc->actual_clock == MMC_HS200_MAX_DTR)
 			temp |= ESDHC_DLL_FREQ_SEL;
 		sdhci_writel(host, temp, ESDHC_DLLCFG0);
+
+		temp |= ESDHC_DLL_RESET;
+		sdhci_writel(host, temp, ESDHC_DLLCFG0);
+		udelay(1);
+		temp &= ~ESDHC_DLL_RESET;
+		sdhci_writel(host, temp, ESDHC_DLLCFG0);
+
+		/* Wait max 20 ms */
+		if (read_poll_timeout(sdhci_readl, temp,
+				      temp & ESDHC_DLL_STS_SLV_LOCK,
+				      10, 20000, false,
+				      host, ESDHC_DLLSTAT0))
+			pr_err("%s: timeout for delay chain lock.\n",
+			       mmc_hostname(host->mmc));
+
 		temp = sdhci_readl(host, ESDHC_TBCTL);
 		sdhci_writel(host, temp | ESDHC_HS400_WNDW_ADJUST, ESDHC_TBCTL);
 
@@ -1052,6 +1069,17 @@ static int esdhc_execute_tuning(struct mmc_host *mmc, u32 opcode)
 
 	esdhc_tuning_block_enable(host, true);
 
+	/*
+	 * The eSDHC controller takes the data timeout value into account
+	 * during tuning. If the SD card is too slow sending the response, the
+	 * timer will expire and a "Buffer Read Ready" interrupt without data
+	 * is triggered. This leads to tuning errors.
+	 *
+	 * Just set the timeout to the maximum value because the core will
+	 * already take care of it in sdhci_send_tuning().
+	 */
+	sdhci_writeb(host, 0xe, SDHCI_TIMEOUT_CONTROL);
+
 	hs400_tuning = host->flags & SDHCI_HS400_TUNING;
 
 	do {
@@ -1296,6 +1324,8 @@ static struct soc_device_attribute soc_fixup_sdhc_clkdivs[] = {
 
 static struct soc_device_attribute soc_unreliable_pulse_detection[] = {
 	{ .family = "QorIQ LX2160A", .revision = "1.0", },
+	{ .family = "QorIQ LX2160A", .revision = "2.0", },
+	{ .family = "QorIQ LS1028A", .revision = "1.0", },
 	{ },
 };
 
diff --git a/drivers/mmc/host/sdhci-pci-core.c b/drivers/mmc/host/sdhci-pci-core.c
index 23da7f7fe093..9552708846ca 100644
--- a/drivers/mmc/host/sdhci-pci-core.c
+++ b/drivers/mmc/host/sdhci-pci-core.c
@@ -665,6 +665,15 @@ static void sdhci_intel_set_power(struct sdhci_host *host, unsigned char mode,
 	}
 }
 
+static void sdhci_intel_set_uhs_signaling(struct sdhci_host *host,
+					  unsigned int timing)
+{
+	/* Set UHS timing to SDR25 for High Speed mode */
+	if (timing == MMC_TIMING_MMC_HS || timing == MMC_TIMING_SD_HS)
+		timing = MMC_TIMING_UHS_SDR25;
+	sdhci_set_uhs_signaling(host, timing);
+}
+
 #define INTEL_HS400_ES_REG 0x78
 #define INTEL_HS400_ES_BIT BIT(0)
 
@@ -721,7 +730,7 @@ static const struct sdhci_ops sdhci_intel_byt_ops = {
 	.enable_dma		= sdhci_pci_enable_dma,
 	.set_bus_width		= sdhci_set_bus_width,
 	.reset			= sdhci_reset,
-	.set_uhs_signaling	= sdhci_set_uhs_signaling,
+	.set_uhs_signaling	= sdhci_intel_set_uhs_signaling,
 	.hw_reset		= sdhci_pci_hw_reset,
 };
 
@@ -731,7 +740,7 @@ static const struct sdhci_ops sdhci_intel_glk_ops = {
 	.enable_dma		= sdhci_pci_enable_dma,
 	.set_bus_width		= sdhci_set_bus_width,
 	.reset			= sdhci_cqhci_reset,
-	.set_uhs_signaling	= sdhci_set_uhs_signaling,
+	.set_uhs_signaling	= sdhci_intel_set_uhs_signaling,
 	.hw_reset		= sdhci_pci_hw_reset,
 	.irq			= sdhci_cqhci_irq,
 };
diff --git a/drivers/mmc/host/sdhci.c b/drivers/mmc/host/sdhci.c
index 592a55a34b58..3561ae8a481a 100644
--- a/drivers/mmc/host/sdhci.c
+++ b/drivers/mmc/host/sdhci.c
@@ -1384,9 +1384,11 @@ static inline void sdhci_auto_cmd_select(struct sdhci_host *host,
 	/*
 	 * In case of Version 4.10 or later, use of 'Auto CMD Auto
 	 * Select' is recommended rather than use of 'Auto CMD12
-	 * Enable' or 'Auto CMD23 Enable'.
+	 * Enable' or 'Auto CMD23 Enable'. We require Version 4 Mode
+	 * here because some controllers (e.g sdhci-of-dwmshc) expect it.
 	 */
-	if (host->version >= SDHCI_SPEC_410 && (use_cmd12 || use_cmd23)) {
+	if (host->version >= SDHCI_SPEC_410 && host->v4_mode &&
+	    (use_cmd12 || use_cmd23)) {
 		*mode |= SDHCI_TRNS_AUTO_SEL;
 
 		ctrl2 = sdhci_readw(host, SDHCI_HOST_CONTROL2);
diff --git a/drivers/mmc/host/tmio_mmc_core.c b/drivers/mmc/host/tmio_mmc_core.c
index 2fce0518632d..cb4149fd12e0 100644
--- a/drivers/mmc/host/tmio_mmc_core.c
+++ b/drivers/mmc/host/tmio_mmc_core.c
@@ -175,6 +175,8 @@ static void tmio_mmc_reset(struct tmio_mmc_host *host)
 	if (host->reset)
 		host->reset(host);
 
+	tmio_mmc_abort_dma(host);
+
 	if (host->pdata->flags & TMIO_MMC_SDIO_IRQ) {
 		sd_ctrl_write16(host, CTL_SDIO_IRQ_MASK, host->sdio_irq_mask);
 		sd_ctrl_write16(host, CTL_TRANSACTION_CTL, 0x0001);
@@ -223,8 +225,6 @@ static void tmio_mmc_reset_work(struct work_struct *work)
 
 	/* Ready for new calls */
 	host->mrq = NULL;
-
-	tmio_mmc_abort_dma(host);
 	mmc_request_done(host->mmc, mrq);
 }
 
@@ -927,6 +927,9 @@ static void tmio_mmc_set_ios(struct mmc_host *mmc, struct mmc_ios *ios)
 	switch (ios->power_mode) {
 	case MMC_POWER_OFF:
 		tmio_mmc_power_off(host);
+		/* Downgrade ensures a sane state for tuning HW (e.g. SCC) */
+		if (host->mmc->ops->hs400_downgrade)
+			host->mmc->ops->hs400_downgrade(host->mmc);
 		host->set_clock(host, 0);
 		break;
 	case MMC_POWER_UP: