diff options
Diffstat (limited to 'drivers/mmc/host/sdhci-of-at91.c')
| -rw-r--r-- | drivers/mmc/host/sdhci-of-at91.c | 76 |
1 files changed, 73 insertions, 3 deletions
diff --git a/drivers/mmc/host/sdhci-of-at91.c b/drivers/mmc/host/sdhci-of-at91.c index 2703aa90d018..d4cef713d246 100644 --- a/drivers/mmc/host/sdhci-of-at91.c +++ b/drivers/mmc/host/sdhci-of-at91.c @@ -15,8 +15,10 @@ */ #include <linux/clk.h> +#include <linux/delay.h> #include <linux/err.h> #include <linux/io.h> +#include <linux/kernel.h> #include <linux/mmc/host.h> #include <linux/mmc/slot-gpio.h> #include <linux/module.h> @@ -31,14 +33,60 @@ #define SDMMC_CACR_CAPWREN BIT(0) #define SDMMC_CACR_KEY (0x46 << 8) +#define SDHCI_AT91_PRESET_COMMON_CONF 0x400 /* drv type B, programmable clock mode */ + struct sdhci_at91_priv { struct clk *hclock; struct clk *gck; struct clk *mainck; }; +static void sdhci_at91_set_clock(struct sdhci_host *host, unsigned int clock) +{ + u16 clk; + unsigned long timeout; + + host->mmc->actual_clock = 0; + + /* + * There is no requirement to disable the internal clock before + * changing the SD clock configuration. Moreover, disabling the + * internal clock, changing the configuration and re-enabling the + * internal clock causes some bugs. It can prevent to get the internal + * clock stable flag ready and an unexpected switch to the base clock + * when using presets. + */ + clk = sdhci_readw(host, SDHCI_CLOCK_CONTROL); + clk &= SDHCI_CLOCK_INT_EN; + sdhci_writew(host, clk, SDHCI_CLOCK_CONTROL); + + if (clock == 0) + return; + + clk = sdhci_calc_clk(host, clock, &host->mmc->actual_clock); + + clk |= SDHCI_CLOCK_INT_EN; + sdhci_writew(host, clk, SDHCI_CLOCK_CONTROL); + + /* Wait max 20 ms */ + timeout = 20; + while (!((clk = sdhci_readw(host, SDHCI_CLOCK_CONTROL)) + & SDHCI_CLOCK_INT_STABLE)) { + if (timeout == 0) { + pr_err("%s: Internal clock never stabilised.\n", + mmc_hostname(host->mmc)); + return; + } + timeout--; + mdelay(1); + } + + clk |= SDHCI_CLOCK_CARD_EN; + sdhci_writew(host, clk, SDHCI_CLOCK_CONTROL); +} + static const struct sdhci_ops sdhci_at91_sama5d2_ops = { - .set_clock = sdhci_set_clock, + .set_clock = sdhci_at91_set_clock, .set_bus_width = sdhci_set_bus_width, .reset = sdhci_reset, .set_uhs_signaling = sdhci_set_uhs_signaling, @@ -46,7 +94,6 @@ static const struct sdhci_ops sdhci_at91_sama5d2_ops = { static const struct sdhci_pltfm_data soc_data_sama5d2 = { .ops = &sdhci_at91_sama5d2_ops, - .quirks2 = SDHCI_QUIRK2_NEED_DELAY_AFTER_INT_CLK_RST, }; static const struct of_device_id sdhci_at91_dt_match[] = { @@ -119,6 +166,7 @@ static int sdhci_at91_probe(struct platform_device *pdev) unsigned int clk_base, clk_mul; unsigned int gck_rate, real_gck_rate; int ret; + unsigned int preset_div; match = of_match_device(sdhci_at91_dt_match, &pdev->dev); if (!match) @@ -186,6 +234,28 @@ static int sdhci_at91_probe(struct platform_device *pdev) clk_mul, real_gck_rate); } + /* + * We have to set preset values because it depends on the clk_mul + * value. Moreover, SDR104 is supported in a degraded mode since the + * maximum sd clock value is 120 MHz instead of 208 MHz. For that + * reason, we need to use presets to support SDR104. + */ + preset_div = DIV_ROUND_UP(real_gck_rate, 24000000) - 1; + writew(SDHCI_AT91_PRESET_COMMON_CONF | preset_div, + host->ioaddr + SDHCI_PRESET_FOR_SDR12); + preset_div = DIV_ROUND_UP(real_gck_rate, 50000000) - 1; + writew(SDHCI_AT91_PRESET_COMMON_CONF | preset_div, + host->ioaddr + SDHCI_PRESET_FOR_SDR25); + preset_div = DIV_ROUND_UP(real_gck_rate, 100000000) - 1; + writew(SDHCI_AT91_PRESET_COMMON_CONF | preset_div, + host->ioaddr + SDHCI_PRESET_FOR_SDR50); + preset_div = DIV_ROUND_UP(real_gck_rate, 120000000) - 1; + writew(SDHCI_AT91_PRESET_COMMON_CONF | preset_div, + host->ioaddr + SDHCI_PRESET_FOR_SDR104); + preset_div = DIV_ROUND_UP(real_gck_rate, 50000000) - 1; + writew(SDHCI_AT91_PRESET_COMMON_CONF | preset_div, + host->ioaddr + SDHCI_PRESET_FOR_DDR50); + clk_prepare_enable(priv->mainck); clk_prepare_enable(priv->gck); @@ -219,7 +289,7 @@ static int sdhci_at91_probe(struct platform_device *pdev) * to enable polling via device tree with broken-cd property. */ if (!(host->mmc->caps & MMC_CAP_NONREMOVABLE) && - IS_ERR_VALUE(mmc_gpio_get_cd(host->mmc))) { + mmc_gpio_get_cd(host->mmc) < 0) { host->mmc->caps |= MMC_CAP_NEEDS_POLL; host->quirks &= ~SDHCI_QUIRK_BROKEN_CARD_DETECTION; } |