1 files changed, 341 insertions, 0 deletions
diff --git a/drivers/media/i2c/max9271.c b/drivers/media/i2c/max9271.c
new file mode 100644
index 000000000000..0f6f7a092a46
--- /dev/null
+++ b/drivers/media/i2c/max9271.c
@@ -0,0 +1,341 @@
+// SPDX-License-Identifier: GPL-2.0+
+/*
+ * Copyright (C) 2017-2020 Jacopo Mondi
+ * Copyright (C) 2017-2020 Kieran Bingham
+ * Copyright (C) 2017-2020 Laurent Pinchart
+ * Copyright (C) 2017-2020 Niklas Söderlund
+ * Copyright (C) 2016 Renesas Electronics Corporation
+ * Copyright (C) 2015 Cogent Embedded, Inc.
+ *
+ * This file exports functions to control the Maxim MAX9271 GMSL serializer
+ * chip. This is not a self-contained driver, as MAX9271 is usually embedded in
+ * camera modules with at least one image sensor and optional additional
+ * components, such as uController units or ISPs/DSPs.
+ *
+ * Drivers for the camera modules (i.e. rdacm20/21) are expected to use
+ * functions exported from this library driver to maximize code re-use.
+ */
+
+#include <linux/delay.h>
+#include <linux/i2c.h>
+
+#include "max9271.h"
+
+static int max9271_read(struct max9271_device *dev, u8 reg)
+{
+	int ret;
+
+	dev_dbg(&dev->client->dev, "%s(0x%02x)\n", __func__, reg);
+
+	ret = i2c_smbus_read_byte_data(dev->client, reg);
+	if (ret < 0)
+		dev_dbg(&dev->client->dev,
+			"%s: register 0x%02x read failed (%d)\n",
+			__func__, reg, ret);
+
+	return ret;
+}
+
+static int max9271_write(struct max9271_device *dev, u8 reg, u8 val)
+{
+	int ret;
+
+	dev_dbg(&dev->client->dev, "%s(0x%02x, 0x%02x)\n", __func__, reg, val);
+
+	ret = i2c_smbus_write_byte_data(dev->client, reg, val);
+	if (ret < 0)
+		dev_err(&dev->client->dev,
+			"%s: register 0x%02x write failed (%d)\n",
+			__func__, reg, ret);
+
+	return ret;
+}
+
+/*
+ * max9271_pclk_detect() - Detect valid pixel clock from image sensor
+ *
+ * Wait up to 10ms for a valid pixel clock.
+ *
+ * Returns 0 for success, < 0 for pixel clock not properly detected
+ */
+static int max9271_pclk_detect(struct max9271_device *dev)
+{
+	unsigned int i;
+	int ret;
+
+	for (i = 0; i < 100; i++) {
+		ret = max9271_read(dev, 0x15);
+		if (ret < 0)
+			return ret;
+
+		if (ret & MAX9271_PCLKDET)
+			return 0;
+
+		usleep_range(50, 100);
+	}
+
+	dev_err(&dev->client->dev, "Unable to detect valid pixel clock\n");
+
+	return -EIO;
+}
+
+int max9271_set_serial_link(struct max9271_device *dev, bool enable)
+{
+	int ret;
+	u8 val = MAX9271_REVCCEN | MAX9271_FWDCCEN;
+
+	if (enable) {
+		ret = max9271_pclk_detect(dev);
+		if (ret)
+			return ret;
+
+		val |= MAX9271_SEREN;
+	} else {
+		val |= MAX9271_CLINKEN;
+	}
+
+	/*
+	 * The serializer temporarily disables the reverse control channel for
+	 * 350µs after starting/stopping the forward serial link, but the
+	 * deserializer synchronization time isn't clearly documented.
+	 *
+	 * According to the serializer datasheet we should wait 3ms, while
+	 * according to the deserializer datasheet we should wait 5ms.
+	 *
+	 * Short delays here appear to show bit-errors in the writes following.
+	 * Therefore a conservative delay seems best here.
+	 */
+	max9271_write(dev, 0x04, val);
+	usleep_range(5000, 8000);
+
+	return 0;
+}
+EXPORT_SYMBOL_GPL(max9271_set_serial_link);
+
+int max9271_configure_i2c(struct max9271_device *dev, u8 i2c_config)
+{
+	int ret;
+
+	ret = max9271_write(dev, 0x0d, i2c_config);
+	if (ret)
+		return ret;
+
+	/* The delay required after an I2C bus configuration change is not
+	 * characterized in the serializer manual. Sleep up to 5msec to
+	 * stay safe.
+	 */
+	usleep_range(3500, 5000);
+
+	return 0;
+}
+EXPORT_SYMBOL_GPL(max9271_configure_i2c);
+
+int max9271_set_high_threshold(struct max9271_device *dev, bool enable)
+{
+	int ret;
+
+	ret = max9271_read(dev, 0x08);
+	if (ret < 0)
+		return ret;
+
+	/*
+	 * Enable or disable reverse channel high threshold to increase
+	 * immunity to power supply noise.
+	 */
+	max9271_write(dev, 0x08, enable ? ret | BIT(0) : ret & ~BIT(0));
+	usleep_range(2000, 2500);
+
+	return 0;
+}
+EXPORT_SYMBOL_GPL(max9271_set_high_threshold);
+
+int max9271_configure_gmsl_link(struct max9271_device *dev)
+{
+	/*
+	 * Configure the GMSL link:
+	 *
+	 * - Double input mode, high data rate, 24-bit mode
+	 * - Latch input data on PCLKIN rising edge
+	 * - Enable HS/VS encoding
+	 * - 1-bit parity error detection
+	 *
+	 * TODO: Make the GMSL link configuration parametric.
+	 */
+	max9271_write(dev, 0x07, MAX9271_DBL | MAX9271_HVEN |
+		      MAX9271_EDC_1BIT_PARITY);
+	usleep_range(5000, 8000);
+
+	/*
+	 * Adjust spread spectrum to +4% and auto-detect pixel clock
+	 * and serial link rate.
+	 */
+	max9271_write(dev, 0x02, MAX9271_SPREAD_SPECT_4 | MAX9271_R02_RES |
+		      MAX9271_PCLK_AUTODETECT | MAX9271_SERIAL_AUTODETECT);
+	usleep_range(5000, 8000);
+
+	return 0;
+}
+EXPORT_SYMBOL_GPL(max9271_configure_gmsl_link);
+
+int max9271_set_gpios(struct max9271_device *dev, u8 gpio_mask)
+{
+	int ret;
+
+	ret = max9271_read(dev, 0x0f);
+	if (ret < 0)
+		return 0;
+
+	ret |= gpio_mask;
+	ret = max9271_write(dev, 0x0f, ret);
+	if (ret < 0) {
+		dev_err(&dev->client->dev, "Failed to set gpio (%d)\n", ret);
+		return ret;
+	}
+
+	usleep_range(3500, 5000);
+
+	return 0;
+}
+EXPORT_SYMBOL_GPL(max9271_set_gpios);
+
+int max9271_clear_gpios(struct max9271_device *dev, u8 gpio_mask)
+{
+	int ret;
+
+	ret = max9271_read(dev, 0x0f);
+	if (ret < 0)
+		return 0;
+
+	ret &= ~gpio_mask;
+	ret = max9271_write(dev, 0x0f, ret);
+	if (ret < 0) {
+		dev_err(&dev->client->dev, "Failed to clear gpio (%d)\n", ret);
+		return ret;
+	}
+
+	usleep_range(3500, 5000);
+
+	return 0;
+}
+EXPORT_SYMBOL_GPL(max9271_clear_gpios);
+
+int max9271_enable_gpios(struct max9271_device *dev, u8 gpio_mask)
+{
+	int ret;
+
+	ret = max9271_read(dev, 0x0f);
+	if (ret < 0)
+		return 0;
+
+	/* BIT(0) reserved: GPO is always enabled. */
+	ret |= gpio_mask | BIT(0);
+	ret = max9271_write(dev, 0x0e, ret);
+	if (ret < 0) {
+		dev_err(&dev->client->dev, "Failed to enable gpio (%d)\n", ret);
+		return ret;
+	}
+
+	usleep_range(3500, 5000);
+
+	return 0;
+}
+EXPORT_SYMBOL_GPL(max9271_enable_gpios);
+
+int max9271_disable_gpios(struct max9271_device *dev, u8 gpio_mask)
+{
+	int ret;
+
+	ret = max9271_read(dev, 0x0f);
+	if (ret < 0)
+		return 0;
+
+	/* BIT(0) reserved: GPO cannot be disabled */
+	ret &= (~gpio_mask | BIT(0));
+	ret = max9271_write(dev, 0x0e, ret);
+	if (ret < 0) {
+		dev_err(&dev->client->dev, "Failed to disable gpio (%d)\n", ret);
+		return ret;
+	}
+
+	usleep_range(3500, 5000);
+
+	return 0;
+}
+EXPORT_SYMBOL_GPL(max9271_disable_gpios);
+
+int max9271_verify_id(struct max9271_device *dev)
+{
+	int ret;
+
+	ret = max9271_read(dev, 0x1e);
+	if (ret < 0) {
+		dev_err(&dev->client->dev, "MAX9271 ID read failed (%d)\n",
+			ret);
+		return ret;
+	}
+
+	if (ret != MAX9271_ID) {
+		dev_err(&dev->client->dev, "MAX9271 ID mismatch (0x%02x)\n",
+			ret);
+		return -ENXIO;
+	}
+
+	return 0;
+}
+EXPORT_SYMBOL_GPL(max9271_verify_id);
+
+int max9271_set_address(struct max9271_device *dev, u8 addr)
+{
+	int ret;
+
+	ret = max9271_write(dev, 0x00, addr << 1);
+	if (ret < 0) {
+		dev_err(&dev->client->dev,
+			"MAX9271 I2C address change failed (%d)\n", ret);
+		return ret;
+	}
+	usleep_range(3500, 5000);
+
+	return 0;
+}
+EXPORT_SYMBOL_GPL(max9271_set_address);
+
+int max9271_set_deserializer_address(struct max9271_device *dev, u8 addr)
+{
+	int ret;
+
+	ret = max9271_write(dev, 0x01, addr << 1);
+	if (ret < 0) {
+		dev_err(&dev->client->dev,
+			"MAX9271 deserializer address set failed (%d)\n", ret);
+		return ret;
+	}
+	usleep_range(3500, 5000);
+
+	return 0;
+}
+EXPORT_SYMBOL_GPL(max9271_set_deserializer_address);
+
+int max9271_set_translation(struct max9271_device *dev, u8 source, u8 dest)
+{
+	int ret;
+
+	ret = max9271_write(dev, 0x09, source << 1);
+	if (ret < 0) {
+		dev_err(&dev->client->dev,
+			"MAX9271 I2C translation setup failed (%d)\n", ret);
+		return ret;
+	}
+	usleep_range(3500, 5000);
+
+	ret = max9271_write(dev, 0x0a, dest << 1);
+	if (ret < 0) {
+		dev_err(&dev->client->dev,
+			"MAX9271 I2C translation setup failed (%d)\n", ret);
+		return ret;
+	}
+	usleep_range(3500, 5000);
+
+	return 0;
+}
+EXPORT_SYMBOL_GPL(max9271_set_translation);