diff options
Diffstat (limited to 'drivers/gpu/drm')
| -rw-r--r-- | drivers/gpu/drm/panel/Kconfig | 10 | ||||
| -rw-r--r-- | drivers/gpu/drm/panel/Makefile | 1 | ||||
| -rw-r--r-- | drivers/gpu/drm/panel/panel-sitronix-st7701.c | 426 |
3 files changed, 437 insertions, 0 deletions
diff --git a/drivers/gpu/drm/panel/Kconfig b/drivers/gpu/drm/panel/Kconfig index a71f44191273..1aeb4a901d06 100644 --- a/drivers/gpu/drm/panel/Kconfig +++ b/drivers/gpu/drm/panel/Kconfig @@ -196,6 +196,16 @@ config DRM_PANEL_SHARP_LS043T1LE01 Say Y here if you want to enable support for Sharp LS043T1LE01 qHD (540x960) DSI panel as found on the Qualcomm APQ8074 Dragonboard +config DRM_PANEL_SITRONIX_ST7701 + tristate "Sitronix ST7701 panel driver" + depends on OF + depends on DRM_MIPI_DSI + depends on BACKLIGHT_CLASS_DEVICE + help + Say Y here if you want to enable support for the Sitronix + ST7701 controller for 480X864 LCD panels with MIPI/RGB/SPI + system interfaces. + config DRM_PANEL_SITRONIX_ST7789V tristate "Sitronix ST7789V panel" depends on OF && SPI diff --git a/drivers/gpu/drm/panel/Makefile b/drivers/gpu/drm/panel/Makefile index cd14ca39c6e0..999d27311490 100644 --- a/drivers/gpu/drm/panel/Makefile +++ b/drivers/gpu/drm/panel/Makefile @@ -20,6 +20,7 @@ obj-$(CONFIG_DRM_PANEL_SAMSUNG_S6E8AA0) += panel-samsung-s6e8aa0.o obj-$(CONFIG_DRM_PANEL_SEIKO_43WVF1G) += panel-seiko-43wvf1g.o obj-$(CONFIG_DRM_PANEL_SHARP_LQ101R1SX01) += panel-sharp-lq101r1sx01.o obj-$(CONFIG_DRM_PANEL_SHARP_LS043T1LE01) += panel-sharp-ls043t1le01.o +obj-$(CONFIG_DRM_PANEL_SITRONIX_ST7701) += panel-sitronix-st7701.o obj-$(CONFIG_DRM_PANEL_SITRONIX_ST7789V) += panel-sitronix-st7789v.o obj-$(CONFIG_DRM_PANEL_TPO_TPG110) += panel-tpo-tpg110.o obj-$(CONFIG_DRM_PANEL_TRULY_NT35597_WQXGA) += panel-truly-nt35597.o diff --git a/drivers/gpu/drm/panel/panel-sitronix-st7701.c b/drivers/gpu/drm/panel/panel-sitronix-st7701.c new file mode 100644 index 000000000000..63f9a1c7fb1b --- /dev/null +++ b/drivers/gpu/drm/panel/panel-sitronix-st7701.c @@ -0,0 +1,426 @@ +// SPDX-License-Identifier: GPL-2.0+ +/* + * Copyright (C) 2019, Amarula Solutions. + * Author: Jagan Teki <jagan@amarulasolutions.com> + */ + +#include <drm/drm_mipi_dsi.h> +#include <drm/drm_modes.h> +#include <drm/drm_panel.h> +#include <drm/drm_print.h> + +#include <linux/backlight.h> +#include <linux/gpio/consumer.h> +#include <linux/delay.h> +#include <linux/module.h> +#include <linux/of_device.h> +#include <linux/regulator/consumer.h> + +#include <video/mipi_display.h> + +/* Command2 BKx selection command */ +#define DSI_CMD2BKX_SEL 0xFF + +/* Command2, BK0 commands */ +#define DSI_CMD2_BK0_PVGAMCTRL 0xB0 /* Positive Voltage Gamma Control */ +#define DSI_CMD2_BK0_NVGAMCTRL 0xB1 /* Negative Voltage Gamma Control */ +#define DSI_CMD2_BK0_LNESET 0xC0 /* Display Line setting */ +#define DSI_CMD2_BK0_PORCTRL 0xC1 /* Porch control */ +#define DSI_CMD2_BK0_INVSEL 0xC2 /* Inversion selection, Frame Rate Control */ + +/* Command2, BK1 commands */ +#define DSI_CMD2_BK1_VRHS 0xB0 /* Vop amplitude setting */ +#define DSI_CMD2_BK1_VCOM 0xB1 /* VCOM amplitude setting */ +#define DSI_CMD2_BK1_VGHSS 0xB2 /* VGH Voltage setting */ +#define DSI_CMD2_BK1_TESTCMD 0xB3 /* TEST Command Setting */ +#define DSI_CMD2_BK1_VGLS 0xB5 /* VGL Voltage setting */ +#define DSI_CMD2_BK1_PWCTLR1 0xB7 /* Power Control 1 */ +#define DSI_CMD2_BK1_PWCTLR2 0xB8 /* Power Control 2 */ +#define DSI_CMD2_BK1_SPD1 0xC1 /* Source pre_drive timing set1 */ +#define DSI_CMD2_BK1_SPD2 0xC2 /* Source EQ2 Setting */ +#define DSI_CMD2_BK1_MIPISET1 0xD0 /* MIPI Setting 1 */ + +/** + * Command2 with BK function selection. + * + * BIT[4, 0]: [CN2, BKXSEL] + * 10 = CMD2BK0, Command2 BK0 + * 11 = CMD2BK1, Command2 BK1 + * 00 = Command2 disable + */ +#define DSI_CMD2BK1_SEL 0x11 +#define DSI_CMD2BK0_SEL 0x10 +#define DSI_CMD2BKX_SEL_NONE 0x00 + +/* Command2, BK0 bytes */ +#define DSI_LINESET_LINE 0x69 +#define DSI_LINESET_LDE_EN BIT(7) +#define DSI_LINESET_LINEDELTA GENMASK(1, 0) +#define DSI_CMD2_BK0_LNESET_B1 DSI_LINESET_LINEDELTA +#define DSI_CMD2_BK0_LNESET_B0 (DSI_LINESET_LDE_EN | DSI_LINESET_LINE) +#define DSI_INVSEL_DEFAULT GENMASK(5, 4) +#define DSI_INVSEL_NLINV GENMASK(2, 0) +#define DSI_INVSEL_RTNI GENMASK(2, 1) +#define DSI_CMD2_BK0_INVSEL_B1 DSI_INVSEL_RTNI +#define DSI_CMD2_BK0_INVSEL_B0 (DSI_INVSEL_DEFAULT | DSI_INVSEL_NLINV) +#define DSI_CMD2_BK0_PORCTRL_B0(m) ((m)->vtotal - (m)->vsync_end) +#define DSI_CMD2_BK0_PORCTRL_B1(m) ((m)->vsync_start - (m)->vdisplay) + +/* Command2, BK1 bytes */ +#define DSI_CMD2_BK1_VRHA_SET 0x45 +#define DSI_CMD2_BK1_VCOM_SET 0x13 +#define DSI_CMD2_BK1_VGHSS_SET GENMASK(2, 0) +#define DSI_CMD2_BK1_TESTCMD_VAL BIT(7) +#define DSI_VGLS_DEFAULT BIT(6) +#define DSI_VGLS_SEL GENMASK(2, 0) +#define DSI_CMD2_BK1_VGLS_SET (DSI_VGLS_DEFAULT | DSI_VGLS_SEL) +#define DSI_PWCTLR1_AP BIT(7) /* Gamma OP bias, max */ +#define DSI_PWCTLR1_APIS BIT(2) /* Source OP input bias, min */ +#define DSI_PWCTLR1_APOS BIT(0) /* Source OP output bias, min */ +#define DSI_CMD2_BK1_PWCTLR1_SET (DSI_PWCTLR1_AP | DSI_PWCTLR1_APIS | \ + DSI_PWCTLR1_APOS) +#define DSI_PWCTLR2_AVDD BIT(5) /* AVDD 6.6v */ +#define DSI_PWCTLR2_AVCL 0x0 /* AVCL -4.4v */ +#define DSI_CMD2_BK1_PWCTLR2_SET (DSI_PWCTLR2_AVDD | DSI_PWCTLR2_AVCL) +#define DSI_SPD1_T2D BIT(3) +#define DSI_CMD2_BK1_SPD1_SET (GENMASK(6, 4) | DSI_SPD1_T2D) +#define DSI_CMD2_BK1_SPD2_SET DSI_CMD2_BK1_SPD1_SET +#define DSI_MIPISET1_EOT_EN BIT(3) +#define DSI_CMD2_BK1_MIPISET1_SET (BIT(7) | DSI_MIPISET1_EOT_EN) + +struct st7701_panel_desc { + const struct drm_display_mode *mode; + unsigned int lanes; + unsigned long flags; + enum mipi_dsi_pixel_format format; + const char *const *supply_names; + unsigned int num_supplies; + unsigned int panel_sleep_delay; +}; + +struct st7701 { + struct drm_panel panel; + struct mipi_dsi_device *dsi; + const struct st7701_panel_desc *desc; + + struct backlight_device *backlight; + struct regulator_bulk_data *supplies; + struct gpio_desc *reset; + unsigned int sleep_delay; +}; + +static inline struct st7701 *panel_to_st7701(struct drm_panel *panel) +{ + return container_of(panel, struct st7701, panel); +} + +static inline int st7701_dsi_write(struct st7701 *st7701, const void *seq, + size_t len) +{ + return mipi_dsi_dcs_write_buffer(st7701->dsi, seq, len); +} + +#define ST7701_DSI(st7701, seq...) \ + { \ + const u8 d[] = { seq }; \ + st7701_dsi_write(st7701, d, ARRAY_SIZE(d)); \ + } + +static void st7701_init_sequence(struct st7701 *st7701) +{ + const struct drm_display_mode *mode = st7701->desc->mode; + + ST7701_DSI(st7701, MIPI_DCS_SOFT_RESET, 0x00); + + /* We need to wait 5ms before sending new commands */ + msleep(5); + + ST7701_DSI(st7701, MIPI_DCS_EXIT_SLEEP_MODE, 0x00); + + msleep(st7701->sleep_delay); + + /* Command2, BK0 */ + ST7701_DSI(st7701, DSI_CMD2BKX_SEL, + 0x77, 0x01, 0x00, 0x00, DSI_CMD2BK0_SEL); + ST7701_DSI(st7701, DSI_CMD2_BK0_PVGAMCTRL, 0x00, 0x0E, 0x15, 0x0F, + 0x11, 0x08, 0x08, 0x08, 0x08, 0x23, 0x04, 0x13, 0x12, + 0x2B, 0x34, 0x1F); + ST7701_DSI(st7701, DSI_CMD2_BK0_NVGAMCTRL, 0x00, 0x0E, 0x95, 0x0F, + 0x13, 0x07, 0x09, 0x08, 0x08, 0x22, 0x04, 0x10, 0x0E, + 0x2C, 0x34, 0x1F); + ST7701_DSI(st7701, DSI_CMD2_BK0_LNESET, + DSI_CMD2_BK0_LNESET_B0, DSI_CMD2_BK0_LNESET_B1); + ST7701_DSI(st7701, DSI_CMD2_BK0_PORCTRL, + DSI_CMD2_BK0_PORCTRL_B0(mode), + DSI_CMD2_BK0_PORCTRL_B1(mode)); + ST7701_DSI(st7701, DSI_CMD2_BK0_INVSEL, + DSI_CMD2_BK0_INVSEL_B0, DSI_CMD2_BK0_INVSEL_B1); + + /* Command2, BK1 */ + ST7701_DSI(st7701, DSI_CMD2BKX_SEL, + 0x77, 0x01, 0x00, 0x00, DSI_CMD2BK1_SEL); + ST7701_DSI(st7701, DSI_CMD2_BK1_VRHS, DSI_CMD2_BK1_VRHA_SET); + ST7701_DSI(st7701, DSI_CMD2_BK1_VCOM, DSI_CMD2_BK1_VCOM_SET); + ST7701_DSI(st7701, DSI_CMD2_BK1_VGHSS, DSI_CMD2_BK1_VGHSS_SET); + ST7701_DSI(st7701, DSI_CMD2_BK1_TESTCMD, DSI_CMD2_BK1_TESTCMD_VAL); + ST7701_DSI(st7701, DSI_CMD2_BK1_VGLS, DSI_CMD2_BK1_VGLS_SET); + ST7701_DSI(st7701, DSI_CMD2_BK1_PWCTLR1, DSI_CMD2_BK1_PWCTLR1_SET); + ST7701_DSI(st7701, DSI_CMD2_BK1_PWCTLR2, DSI_CMD2_BK1_PWCTLR2_SET); + ST7701_DSI(st7701, DSI_CMD2_BK1_SPD1, DSI_CMD2_BK1_SPD1_SET); + ST7701_DSI(st7701, DSI_CMD2_BK1_SPD2, DSI_CMD2_BK1_SPD2_SET); + ST7701_DSI(st7701, DSI_CMD2_BK1_MIPISET1, DSI_CMD2_BK1_MIPISET1_SET); + + /** + * ST7701_SPEC_V1.2 is unable to provide enough information above this + * specific command sequence, so grab the same from vendor BSP driver. + */ + ST7701_DSI(st7701, 0xE0, 0x00, 0x00, 0x02); + ST7701_DSI(st7701, 0xE1, 0x0B, 0x00, 0x0D, 0x00, 0x0C, 0x00, 0x0E, + 0x00, 0x00, 0x44, 0x44); + ST7701_DSI(st7701, 0xE2, 0x33, 0x33, 0x44, 0x44, 0x64, 0x00, 0x66, + 0x00, 0x65, 0x00, 0x67, 0x00, 0x00); + ST7701_DSI(st7701, 0xE3, 0x00, 0x00, 0x33, 0x33); + ST7701_DSI(st7701, 0xE4, 0x44, 0x44); + ST7701_DSI(st7701, 0xE5, 0x0C, 0x78, 0x3C, 0xA0, 0x0E, 0x78, 0x3C, + 0xA0, 0x10, 0x78, 0x3C, 0xA0, 0x12, 0x78, 0x3C, 0xA0); + ST7701_DSI(st7701, 0xE6, 0x00, 0x00, 0x33, 0x33); + ST7701_DSI(st7701, 0xE7, 0x44, 0x44); + ST7701_DSI(st7701, 0xE8, 0x0D, 0x78, 0x3C, 0xA0, 0x0F, 0x78, 0x3C, + 0xA0, 0x11, 0x78, 0x3C, 0xA0, 0x13, 0x78, 0x3C, 0xA0); + ST7701_DSI(st7701, 0xEB, 0x02, 0x02, 0x39, 0x39, 0xEE, 0x44, 0x00); + ST7701_DSI(st7701, 0xEC, 0x00, 0x00); + ST7701_DSI(st7701, 0xED, 0xFF, 0xF1, 0x04, 0x56, 0x72, 0x3F, 0xFF, + 0xFF, 0xFF, 0xFF, 0xF3, 0x27, 0x65, 0x40, 0x1F, 0xFF); + + /* disable Command2 */ + ST7701_DSI(st7701, DSI_CMD2BKX_SEL, + 0x77, 0x01, 0x00, 0x00, DSI_CMD2BKX_SEL_NONE); +} + +static int st7701_prepare(struct drm_panel *panel) +{ + struct st7701 *st7701 = panel_to_st7701(panel); + int ret; + + gpiod_set_value(st7701->reset, 0); + + ret = regulator_bulk_enable(st7701->desc->num_supplies, + st7701->supplies); + if (ret < 0) + return ret; + msleep(20); + + gpiod_set_value(st7701->reset, 1); + msleep(150); + + st7701_init_sequence(st7701); + + return 0; +} + +static int st7701_enable(struct drm_panel *panel) +{ + struct st7701 *st7701 = panel_to_st7701(panel); + + ST7701_DSI(st7701, MIPI_DCS_SET_DISPLAY_ON, 0x00); + backlight_enable(st7701->backlight); + + return 0; +} + +static int st7701_disable(struct drm_panel *panel) +{ + struct st7701 *st7701 = panel_to_st7701(panel); + + backlight_disable(st7701->backlight); + ST7701_DSI(st7701, MIPI_DCS_SET_DISPLAY_OFF, 0x00); + + return 0; +} + +static int st7701_unprepare(struct drm_panel *panel) +{ + struct st7701 *st7701 = panel_to_st7701(panel); + + ST7701_DSI(st7701, MIPI_DCS_ENTER_SLEEP_MODE, 0x00); + + msleep(st7701->sleep_delay); + + gpiod_set_value(st7701->reset, 0); + + /** + * During the Resetting period, the display will be blanked + * (The display is entering blanking sequence, which maximum + * time is 120 ms, when Reset Starts in Sleep Out –mode. The + * display remains the blank state in Sleep In –mode.) and + * then return to Default condition for Hardware Reset. + * + * So we need wait sleep_delay time to make sure reset completed. + */ + msleep(st7701->sleep_delay); + + regulator_bulk_disable(st7701->desc->num_supplies, st7701->supplies); + + return 0; +} + +static int st7701_get_modes(struct drm_panel *panel) +{ + struct st7701 *st7701 = panel_to_st7701(panel); + const struct drm_display_mode *desc_mode = st7701->desc->mode; + struct drm_display_mode *mode; + + mode = drm_mode_duplicate(panel->drm, desc_mode); + if (!mode) { + DRM_DEV_ERROR(&st7701->dsi->dev, + "failed to add mode %ux%ux@%u\n", + desc_mode->hdisplay, desc_mode->vdisplay, + desc_mode->vrefresh); + return -ENOMEM; + } + + drm_mode_set_name(mode); + drm_mode_probed_add(panel->connector, mode); + + panel->connector->display_info.width_mm = desc_mode->width_mm; + panel->connector->display_info.height_mm = desc_mode->height_mm; + + return 1; +} + +static const struct drm_panel_funcs st7701_funcs = { + .disable = st7701_disable, + .unprepare = st7701_unprepare, + .prepare = st7701_prepare, + .enable = st7701_enable, + .get_modes = st7701_get_modes, +}; + +static const struct drm_display_mode ts8550b_mode = { + .clock = 27500, + + .hdisplay = 480, + .hsync_start = 480 + 38, + .hsync_end = 480 + 38 + 12, + .htotal = 480 + 38 + 12 + 12, + + .vdisplay = 854, + .vsync_start = 854 + 4, + .vsync_end = 854 + 4 + 8, + .vtotal = 854 + 4 + 8 + 18, + + .width_mm = 69, + .height_mm = 139, + + .type = DRM_MODE_TYPE_DRIVER | DRM_MODE_TYPE_PREFERRED, +}; + +static const char * const ts8550b_supply_names[] = { + "VCC", + "IOVCC", +}; + +static const struct st7701_panel_desc ts8550b_desc = { + .mode = &ts8550b_mode, + .lanes = 2, + .flags = MIPI_DSI_MODE_VIDEO, + .format = MIPI_DSI_FMT_RGB888, + .supply_names = ts8550b_supply_names, + .num_supplies = ARRAY_SIZE(ts8550b_supply_names), + .panel_sleep_delay = 80, /* panel need extra 80ms for sleep out cmd */ +}; + +static int st7701_dsi_probe(struct mipi_dsi_device *dsi) +{ + const struct st7701_panel_desc *desc; + struct st7701 *st7701; + int ret, i; + + st7701 = devm_kzalloc(&dsi->dev, sizeof(*st7701), GFP_KERNEL); + if (!st7701) + return -ENOMEM; + + desc = of_device_get_match_data(&dsi->dev); + dsi->mode_flags = desc->flags; + dsi->format = desc->format; + dsi->lanes = desc->lanes; + + st7701->supplies = devm_kcalloc(&dsi->dev, desc->num_supplies, + sizeof(*st7701->supplies), + GFP_KERNEL); + if (!st7701->supplies) + return -ENOMEM; + + for (i = 0; i < desc->num_supplies; i++) + st7701->supplies[i].supply = desc->supply_names[i]; + + ret = devm_regulator_bulk_get(&dsi->dev, desc->num_supplies, + st7701->supplies); + if (ret < 0) + return ret; + + st7701->reset = devm_gpiod_get(&dsi->dev, "reset", GPIOD_OUT_LOW); + if (IS_ERR(st7701->reset)) { + DRM_DEV_ERROR(&dsi->dev, "Couldn't get our reset GPIO\n"); + return PTR_ERR(st7701->reset); + } + + st7701->backlight = devm_of_find_backlight(&dsi->dev); + if (IS_ERR(st7701->backlight)) + return PTR_ERR(st7701->backlight); + + drm_panel_init(&st7701->panel); + + /** + * Once sleep out has been issued, ST7701 IC required to wait 120ms + * before initiating new commands. + * + * On top of that some panels might need an extra delay to wait, so + * add panel specific delay for those cases. As now this panel specific + * delay information is referenced from those panel BSP driver, example + * ts8550b and there is no valid documentation for that. + */ + st7701->sleep_delay = 120 + desc->panel_sleep_delay; + st7701->panel.funcs = &st7701_funcs; + st7701->panel.dev = &dsi->dev; + + ret = drm_panel_add(&st7701->panel); + if (ret < 0) + return ret; + + mipi_dsi_set_drvdata(dsi, st7701); + st7701->dsi = dsi; + st7701->desc = desc; + + return mipi_dsi_attach(dsi); +} + +static int st7701_dsi_remove(struct mipi_dsi_device *dsi) +{ + struct st7701 *st7701 = mipi_dsi_get_drvdata(dsi); + + mipi_dsi_detach(dsi); + drm_panel_remove(&st7701->panel); + + return 0; +} + +static const struct of_device_id st7701_of_match[] = { + { .compatible = "techstar,ts8550b", .data = &ts8550b_desc }, + { } +}; +MODULE_DEVICE_TABLE(of, st7701_of_match); + +static struct mipi_dsi_driver st7701_dsi_driver = { + .probe = st7701_dsi_probe, + .remove = st7701_dsi_remove, + .driver = { + .name = "st7701", + .of_match_table = st7701_of_match, + }, +}; +module_mipi_dsi_driver(st7701_dsi_driver); + +MODULE_AUTHOR("Jagan Teki <jagan@amarulasolutions.com>"); +MODULE_DESCRIPTION("Sitronix ST7701 LCD Panel Driver"); +MODULE_LICENSE("GPL"); |