diff options
Diffstat (limited to 'arch/x86/pci/irq.c')
| -rw-r--r-- | arch/x86/pci/irq.c | 279 |
1 files changed, 276 insertions, 3 deletions
diff --git a/arch/x86/pci/irq.c b/arch/x86/pci/irq.c index d3a73f9335e1..97b63e35e152 100644 --- a/arch/x86/pci/irq.c +++ b/arch/x86/pci/irq.c @@ -13,9 +13,13 @@ #include <linux/dmi.h> #include <linux/io.h> #include <linux/smp.h> +#include <linux/spinlock.h> #include <asm/io_apic.h> #include <linux/irq.h> #include <linux/acpi.h> + +#include <asm/i8259.h> +#include <asm/pc-conf-reg.h> #include <asm/pci_x86.h> #define PIRQ_SIGNATURE (('$' << 0) + ('P' << 8) + ('I' << 16) + ('R' << 24)) @@ -47,6 +51,8 @@ struct irq_router { int (*get)(struct pci_dev *router, struct pci_dev *dev, int pirq); int (*set)(struct pci_dev *router, struct pci_dev *dev, int pirq, int new); + int (*lvl)(struct pci_dev *router, struct pci_dev *dev, int pirq, + int irq); }; struct irq_router_handler { @@ -153,7 +159,7 @@ static void __init pirq_peer_trick(void) void elcr_set_level_irq(unsigned int irq) { unsigned char mask = 1 << (irq & 7); - unsigned int port = 0x4d0 + (irq >> 3); + unsigned int port = PIC_ELCR1 + (irq >> 3); unsigned char val; static u16 elcr_irq_mask; @@ -170,6 +176,139 @@ void elcr_set_level_irq(unsigned int irq) } /* + * PIRQ routing for the M1487 ISA Bus Controller (IBC) ASIC used + * with the ALi FinALi 486 chipset. The IBC is not decoded in the + * PCI configuration space, so we identify it by the accompanying + * M1489 Cache-Memory PCI Controller (CMP) ASIC. + * + * There are four 4-bit mappings provided, spread across two PCI + * INTx Routing Table Mapping Registers, available in the port I/O + * space accessible indirectly via the index/data register pair at + * 0x22/0x23, located at indices 0x42 and 0x43 for the INT1/INT2 + * and INT3/INT4 lines respectively. The INT1/INT3 and INT2/INT4 + * lines are mapped in the low and the high 4-bit nibble of the + * corresponding register as follows: + * + * 0000 : Disabled + * 0001 : IRQ9 + * 0010 : IRQ3 + * 0011 : IRQ10 + * 0100 : IRQ4 + * 0101 : IRQ5 + * 0110 : IRQ7 + * 0111 : IRQ6 + * 1000 : Reserved + * 1001 : IRQ11 + * 1010 : Reserved + * 1011 : IRQ12 + * 1100 : Reserved + * 1101 : IRQ14 + * 1110 : Reserved + * 1111 : IRQ15 + * + * In addition to the usual ELCR register pair there is a separate + * PCI INTx Sensitivity Register at index 0x44 in the same port I/O + * space, whose bits 3:0 select the trigger mode for INT[4:1] lines + * respectively. Any bit set to 1 causes interrupts coming on the + * corresponding line to be passed to ISA as edge-triggered and + * otherwise they are passed as level-triggered. Manufacturer's + * documentation says this register has to be set consistently with + * the relevant ELCR register. + * + * Accesses to the port I/O space concerned here need to be unlocked + * by writing the value of 0xc5 to the Lock Register at index 0x03 + * beforehand. Any other value written to said register prevents + * further accesses from reaching the register file, except for the + * Lock Register being written with 0xc5 again. + * + * References: + * + * "M1489/M1487: 486 PCI Chip Set", Version 1.2, Acer Laboratories + * Inc., July 1997 + */ + +#define PC_CONF_FINALI_LOCK 0x03u +#define PC_CONF_FINALI_PCI_INTX_RT1 0x42u +#define PC_CONF_FINALI_PCI_INTX_RT2 0x43u +#define PC_CONF_FINALI_PCI_INTX_SENS 0x44u + +#define PC_CONF_FINALI_LOCK_KEY 0xc5u + +static u8 read_pc_conf_nybble(u8 base, u8 index) +{ + u8 reg = base + (index >> 1); + u8 x; + + x = pc_conf_get(reg); + return index & 1 ? x >> 4 : x & 0xf; +} + +static void write_pc_conf_nybble(u8 base, u8 index, u8 val) +{ + u8 reg = base + (index >> 1); + u8 x; + + x = pc_conf_get(reg); + x = index & 1 ? (x & 0x0f) | (val << 4) : (x & 0xf0) | val; + pc_conf_set(reg, x); +} + +static int pirq_finali_get(struct pci_dev *router, struct pci_dev *dev, + int pirq) +{ + static const u8 irqmap[16] = { + 0, 9, 3, 10, 4, 5, 7, 6, 0, 11, 0, 12, 0, 14, 0, 15 + }; + unsigned long flags; + u8 x; + + raw_spin_lock_irqsave(&pc_conf_lock, flags); + pc_conf_set(PC_CONF_FINALI_LOCK, PC_CONF_FINALI_LOCK_KEY); + x = irqmap[read_pc_conf_nybble(PC_CONF_FINALI_PCI_INTX_RT1, pirq - 1)]; + pc_conf_set(PC_CONF_FINALI_LOCK, 0); + raw_spin_unlock_irqrestore(&pc_conf_lock, flags); + return x; +} + +static int pirq_finali_set(struct pci_dev *router, struct pci_dev *dev, + int pirq, int irq) +{ + static const u8 irqmap[16] = { + 0, 0, 0, 2, 4, 5, 7, 6, 0, 1, 3, 9, 11, 0, 13, 15 + }; + u8 val = irqmap[irq]; + unsigned long flags; + + if (!val) + return 0; + + raw_spin_lock_irqsave(&pc_conf_lock, flags); + pc_conf_set(PC_CONF_FINALI_LOCK, PC_CONF_FINALI_LOCK_KEY); + write_pc_conf_nybble(PC_CONF_FINALI_PCI_INTX_RT1, pirq - 1, val); + pc_conf_set(PC_CONF_FINALI_LOCK, 0); + raw_spin_unlock_irqrestore(&pc_conf_lock, flags); + return 1; +} + +static int pirq_finali_lvl(struct pci_dev *router, struct pci_dev *dev, + int pirq, int irq) +{ + u8 mask = ~(1u << (pirq - 1)); + unsigned long flags; + u8 trig; + + elcr_set_level_irq(irq); + raw_spin_lock_irqsave(&pc_conf_lock, flags); + pc_conf_set(PC_CONF_FINALI_LOCK, PC_CONF_FINALI_LOCK_KEY); + trig = pc_conf_get(PC_CONF_FINALI_PCI_INTX_SENS); + trig &= mask; + pc_conf_set(PC_CONF_FINALI_PCI_INTX_SENS, trig); + pc_conf_set(PC_CONF_FINALI_LOCK, 0); + raw_spin_unlock_irqrestore(&pc_conf_lock, flags); + return 1; +} + +/* * Common IRQ routing practice: nibbles in config space, * offset by some magic constant. */ @@ -220,6 +359,74 @@ static int pirq_ali_set(struct pci_dev *router, struct pci_dev *dev, int pirq, i } /* + * PIRQ routing for the 82374EB/82374SB EISA System Component (ESC) + * ASIC used with the Intel 82420 and 82430 PCIsets. The ESC is not + * decoded in the PCI configuration space, so we identify it by the + * accompanying 82375EB/82375SB PCI-EISA Bridge (PCEB) ASIC. + * + * There are four PIRQ Route Control registers, available in the + * port I/O space accessible indirectly via the index/data register + * pair at 0x22/0x23, located at indices 0x60/0x61/0x62/0x63 for the + * PIRQ0/1/2/3# lines respectively. The semantics is the same as + * with the PIIX router. + * + * Accesses to the port I/O space concerned here need to be unlocked + * by writing the value of 0x0f to the ESC ID Register at index 0x02 + * beforehand. Any other value written to said register prevents + * further accesses from reaching the register file, except for the + * ESC ID Register being written with 0x0f again. + * + * References: + * + * "82374EB/82374SB EISA System Component (ESC)", Intel Corporation, + * Order Number: 290476-004, March 1996 + * + * "82375EB/82375SB PCI-EISA Bridge (PCEB)", Intel Corporation, Order + * Number: 290477-004, March 1996 + */ + +#define PC_CONF_I82374_ESC_ID 0x02u +#define PC_CONF_I82374_PIRQ_ROUTE_CONTROL 0x60u + +#define PC_CONF_I82374_ESC_ID_KEY 0x0fu + +static int pirq_esc_get(struct pci_dev *router, struct pci_dev *dev, int pirq) +{ + unsigned long flags; + int reg; + u8 x; + + reg = pirq; + if (reg >= 1 && reg <= 4) + reg += PC_CONF_I82374_PIRQ_ROUTE_CONTROL - 1; + + raw_spin_lock_irqsave(&pc_conf_lock, flags); + pc_conf_set(PC_CONF_I82374_ESC_ID, PC_CONF_I82374_ESC_ID_KEY); + x = pc_conf_get(reg); + pc_conf_set(PC_CONF_I82374_ESC_ID, 0); + raw_spin_unlock_irqrestore(&pc_conf_lock, flags); + return (x < 16) ? x : 0; +} + +static int pirq_esc_set(struct pci_dev *router, struct pci_dev *dev, int pirq, + int irq) +{ + unsigned long flags; + int reg; + + reg = pirq; + if (reg >= 1 && reg <= 4) + reg += PC_CONF_I82374_PIRQ_ROUTE_CONTROL - 1; + + raw_spin_lock_irqsave(&pc_conf_lock, flags); + pc_conf_set(PC_CONF_I82374_ESC_ID, PC_CONF_I82374_ESC_ID_KEY); + pc_conf_set(reg, irq); + pc_conf_set(PC_CONF_I82374_ESC_ID, 0); + raw_spin_unlock_irqrestore(&pc_conf_lock, flags); + return 1; +} + +/* * The Intel PIIX4 pirq rules are fairly simple: "pirq" is * just a pointer to the config space. */ @@ -238,6 +445,50 @@ static int pirq_piix_set(struct pci_dev *router, struct pci_dev *dev, int pirq, } /* + * PIRQ routing for the 82426EX ISA Bridge (IB) ASIC used with the + * Intel 82420EX PCIset. + * + * There are only two PIRQ Route Control registers, available in the + * combined 82425EX/82426EX PCI configuration space, at 0x66 and 0x67 + * for the PIRQ0# and PIRQ1# lines respectively. The semantics is + * the same as with the PIIX router. + * + * References: + * + * "82420EX PCIset Data Sheet, 82425EX PCI System Controller (PSC) + * and 82426EX ISA Bridge (IB)", Intel Corporation, Order Number: + * 290488-004, December 1995 + */ + +#define PCI_I82426EX_PIRQ_ROUTE_CONTROL 0x66u + +static int pirq_ib_get(struct pci_dev *router, struct pci_dev *dev, int pirq) +{ + int reg; + u8 x; + + reg = pirq; + if (reg >= 1 && reg <= 2) + reg += PCI_I82426EX_PIRQ_ROUTE_CONTROL - 1; + + pci_read_config_byte(router, reg, &x); + return (x < 16) ? x : 0; +} + +static int pirq_ib_set(struct pci_dev *router, struct pci_dev *dev, int pirq, + int irq) +{ + int reg; + + reg = pirq; + if (reg >= 1 && reg <= 2) + reg += PCI_I82426EX_PIRQ_ROUTE_CONTROL - 1; + + pci_write_config_byte(router, reg, irq); + return 1; +} + +/* * The VIA pirq rules are nibble-based, like ALI, * but without the ugly irq number munging. * However, PIRQD is in the upper instead of lower 4 bits. @@ -549,6 +800,11 @@ static __init int intel_router_probe(struct irq_router *r, struct pci_dev *route return 0; switch (device) { + case PCI_DEVICE_ID_INTEL_82375: + r->name = "PCEB/ESC"; + r->get = pirq_esc_get; + r->set = pirq_esc_set; + return 1; case PCI_DEVICE_ID_INTEL_82371FB_0: case PCI_DEVICE_ID_INTEL_82371SB_0: case PCI_DEVICE_ID_INTEL_82371AB_0: @@ -594,6 +850,11 @@ static __init int intel_router_probe(struct irq_router *r, struct pci_dev *route r->get = pirq_piix_get; r->set = pirq_piix_set; return 1; + case PCI_DEVICE_ID_INTEL_82425: + r->name = "PSC/IB"; + r->get = pirq_ib_get; + r->set = pirq_ib_set; + return 1; } if ((device >= PCI_DEVICE_ID_INTEL_5_3400_SERIES_LPC_MIN && @@ -745,6 +1006,12 @@ static __init int ite_router_probe(struct irq_router *r, struct pci_dev *router, static __init int ali_router_probe(struct irq_router *r, struct pci_dev *router, u16 device) { switch (device) { + case PCI_DEVICE_ID_AL_M1489: + r->name = "FinALi"; + r->get = pirq_finali_get; + r->set = pirq_finali_set; + r->lvl = pirq_finali_lvl; + return 1; case PCI_DEVICE_ID_AL_M1533: case PCI_DEVICE_ID_AL_M1563: r->name = "ALI"; @@ -968,11 +1235,17 @@ static int pcibios_lookup_irq(struct pci_dev *dev, int assign) } else if (r->get && (irq = r->get(pirq_router_dev, dev, pirq)) && \ ((!(pci_probe & PCI_USE_PIRQ_MASK)) || ((1 << irq) & mask))) { msg = "found"; - elcr_set_level_irq(irq); + if (r->lvl) + r->lvl(pirq_router_dev, dev, pirq, irq); + else + elcr_set_level_irq(irq); } else if (newirq && r->set && (dev->class >> 8) != PCI_CLASS_DISPLAY_VGA) { if (r->set(pirq_router_dev, dev, pirq, newirq)) { - elcr_set_level_irq(newirq); + if (r->lvl) + r->lvl(pirq_router_dev, dev, pirq, newirq); + else + elcr_set_level_irq(newirq); msg = "assigned"; irq = newirq; } |