diff options
Diffstat (limited to 'arch/arm/mach-gemini/include/mach/global_reg.h')
| -rw-r--r-- | arch/arm/mach-gemini/include/mach/global_reg.h | 278 |
1 files changed, 278 insertions, 0 deletions
diff --git a/arch/arm/mach-gemini/include/mach/global_reg.h b/arch/arm/mach-gemini/include/mach/global_reg.h new file mode 100644 index 000000000000..de7ff7e849fc --- /dev/null +++ b/arch/arm/mach-gemini/include/mach/global_reg.h @@ -0,0 +1,278 @@ +/* + * This file contains the hardware definitions for Gemini. + * + * Copyright (C) 2009 Paulius Zaleckas <paulius.zaleckas@teltonika.lt> + * + * This program is free software; you can redistribute it and/or modify + * it under the terms of the GNU General Public License as published by + * the Free Software Foundation; either version 2 of the License, or + * (at your option) any later version. + */ +#ifndef __MACH_GLOBAL_REG_H +#define __MACH_GLOBAL_REG_H + +/* Global Word ID Register*/ +#define GLOBAL_ID 0x00 + +#define CHIP_ID(reg) ((reg) >> 8) +#define CHIP_REVISION(reg) ((reg) & 0xFF) + +/* Global Status Register */ +#define GLOBAL_STATUS 0x04 + +#define CPU_BIG_ENDIAN (1 << 31) +#define PLL_OSC_30M (1 << 30) /* else 60MHz */ + +#define OPERATION_MODE_MASK (0xF << 26) +#define OPM_IDDQ (0xF << 26) +#define OPM_NAND (0xE << 26) +#define OPM_RING (0xD << 26) +#define OPM_DIRECT_BOOT (0xC << 26) +#define OPM_USB1_PHY_TEST (0xB << 26) +#define OPM_USB0_PHY_TEST (0xA << 26) +#define OPM_SATA1_PHY_TEST (0x9 << 26) +#define OPM_SATA0_PHY_TEST (0x8 << 26) +#define OPM_ICE_ARM (0x7 << 26) +#define OPM_ICE_FARADAY (0x6 << 26) +#define OPM_PLL_BYPASS (0x5 << 26) +#define OPM_DEBUG (0x4 << 26) +#define OPM_BURN_IN (0x3 << 26) +#define OPM_MBIST (0x2 << 26) +#define OPM_SCAN (0x1 << 26) +#define OPM_REAL (0x0 << 26) + +#define FLASH_TYPE_MASK (0x3 << 24) +#define FLASH_TYPE_NAND_2K (0x3 << 24) +#define FLASH_TYPE_NAND_512 (0x2 << 24) +#define FLASH_TYPE_PARALLEL (0x1 << 24) +#define FLASH_TYPE_SERIAL (0x0 << 24) +/* if parallel */ +#define FLASH_WIDTH_16BIT (1 << 23) /* else 8 bit */ +/* if serial */ +#define FLASH_ATMEL (1 << 23) /* else STM */ + +#define FLASH_SIZE_MASK (0x3 << 21) +#define NAND_256M (0x3 << 21) /* and more */ +#define NAND_128M (0x2 << 21) +#define NAND_64M (0x1 << 21) +#define NAND_32M (0x0 << 21) +#define ATMEL_16M (0x3 << 21) /* and more */ +#define ATMEL_8M (0x2 << 21) +#define ATMEL_4M_2M (0x1 << 21) +#define ATMEL_1M (0x0 << 21) /* and less */ +#define STM_32M (1 << 22) /* and more */ +#define STM_16M (0 << 22) /* and less */ + +#define FLASH_PARALLEL_HIGH_PIN_CNT (1 << 20) /* else low pin cnt */ + +#define CPU_AHB_RATIO_MASK (0x3 << 18) +#define CPU_AHB_1_1 (0x0 << 18) +#define CPU_AHB_3_2 (0x1 << 18) +#define CPU_AHB_24_13 (0x2 << 18) +#define CPU_AHB_2_1 (0x3 << 18) + +#define REG_TO_AHB_SPEED(reg) ((((reg) >> 15) & 0x7) * 10 + 130) +#define AHB_SPEED_TO_REG(x) ((((x - 130)) / 10) << 15) + +/* it is posible to override some settings, use >> OVERRIDE_xxxx_SHIFT */ +#define OVERRIDE_FLASH_TYPE_SHIFT 16 +#define OVERRIDE_FLASH_WIDTH_SHIFT 16 +#define OVERRIDE_FLASH_SIZE_SHIFT 16 +#define OVERRIDE_CPU_AHB_RATIO_SHIFT 15 +#define OVERRIDE_AHB_SPEED_SHIFT 15 + +/* Global PLL Control Register */ +#define GLOBAL_PLL_CTRL 0x08 + +#define PLL_BYPASS (1 << 31) +#define PLL_POWER_DOWN (1 << 8) +#define PLL_CONTROL_Q (0x1F << 0) + +/* Global Soft Reset Control Register */ +#define GLOBAL_RESET 0x0C + +#define RESET_GLOBAL (1 << 31) +#define RESET_CPU1 (1 << 30) +#define RESET_TVE (1 << 28) +#define RESET_SATA1 (1 << 27) +#define RESET_SATA0 (1 << 26) +#define RESET_CIR (1 << 25) +#define RESET_EXT_DEV (1 << 24) +#define RESET_WD (1 << 23) +#define RESET_GPIO2 (1 << 22) +#define RESET_GPIO1 (1 << 21) +#define RESET_GPIO0 (1 << 20) +#define RESET_SSP (1 << 19) +#define RESET_UART (1 << 18) +#define RESET_TIMER (1 << 17) +#define RESET_RTC (1 << 16) +#define RESET_INT1 (1 << 15) +#define RESET_INT0 (1 << 14) +#define RESET_LCD (1 << 13) +#define RESET_LPC (1 << 12) +#define RESET_APB (1 << 11) +#define RESET_DMA (1 << 10) +#define RESET_USB1 (1 << 9) +#define RESET_USB0 (1 << 8) +#define RESET_PCI (1 << 7) +#define RESET_GMAC1 (1 << 6) +#define RESET_GMAC0 (1 << 5) +#define RESET_SECURITY (1 << 4) +#define RESET_RAID (1 << 3) +#define RESET_IDE (1 << 2) +#define RESET_FLASH (1 << 1) +#define RESET_DRAM (1 << 0) + +/* Global IO Pad Driving Capability Control Register */ +#define GLOBAL_IO_DRIVING_CTRL 0x10 + +#define DRIVING_CURRENT_MASK 0x3 + +/* here 00-4mA, 01-8mA, 10-12mA, 11-16mA */ +#define GPIO1_PADS_31_28_SHIFT 28 +#define GPIO0_PADS_31_16_SHIFT 26 +#define GPIO0_PADS_15_0_SHIFT 24 +#define PCI_AND_EXT_RESET_PADS_SHIFT 22 +#define IDE_PADS_SHIFT 20 +#define GMAC1_PADS_SHIFT 18 +#define GMAC0_PADS_SHIFT 16 +/* DRAM is not in mA and poorly documented */ +#define DRAM_CLOCK_PADS_SHIFT 8 +#define DRAM_DATA_PADS_SHIFT 4 +#define DRAM_CONTROL_PADS_SHIFT 0 + +/* Global IO Pad Slew Rate Control Register */ +#define GLOBAL_IO_SLEW_RATE_CTRL 0x14 + +#define GPIO1_PADS_31_28_SLOW (1 << 10) +#define GPIO0_PADS_31_16_SLOW (1 << 9) +#define GPIO0_PADS_15_0_SLOW (1 << 8) +#define PCI_PADS_SLOW (1 << 7) +#define IDE_PADS_SLOW (1 << 6) +#define GMAC1_PADS_SLOW (1 << 5) +#define GMAC0_PADS_SLOW (1 << 4) +#define DRAM_CLOCK_PADS_SLOW (1 << 1) +#define DRAM_IO_PADS_SLOW (1 << 0) + +/* + * General skew control defines + * 16 steps, each step is around 0.2ns + */ +#define SKEW_MASK 0xF + +/* Global IDE PAD Skew Control Register */ +#define GLOBAL_IDE_SKEW_CTRL 0x18 + +#define IDE1_HOST_STROBE_DELAY_SHIFT 28 +#define IDE1_DEVICE_STROBE_DELAY_SHIFT 24 +#define IDE1_OUTPUT_IO_SKEW_SHIFT 20 +#define IDE1_INPUT_IO_SKEW_SHIFT 16 +#define IDE0_HOST_STROBE_DELAY_SHIFT 12 +#define IDE0_DEVICE_STROBE_DELAY_SHIFT 8 +#define IDE0_OUTPUT_IO_SKEW_SHIFT 4 +#define IDE0_INPUT_IO_SKEW_SHIFT 0 + +/* Global GMAC Control Pad Skew Control Register */ +#define GLOBAL_GMAC_CTRL_SKEW_CTRL 0x1C + +#define GMAC1_TXC_SKEW_SHIFT 28 +#define GMAC1_TXEN_SKEW_SHIFT 24 +#define GMAC1_RXC_SKEW_SHIFT 20 +#define GMAC1_RXDV_SKEW_SHIFT 16 +#define GMAC0_TXC_SKEW_SHIFT 12 +#define GMAC0_TXEN_SKEW_SHIFT 8 +#define GMAC0_RXC_SKEW_SHIFT 4 +#define GMAC0_RXDV_SKEW_SHIFT 0 + +/* Global GMAC0 Data PAD Skew Control Register */ +#define GLOBAL_GMAC0_DATA_SKEW_CTRL 0x20 +/* Global GMAC1 Data PAD Skew Control Register */ +#define GLOBAL_GMAC1_DATA_SKEW_CTRL 0x24 + +#define GMAC_TXD_SKEW_SHIFT(x) (((x) * 4) + 16) +#define GMAC_RXD_SKEW_SHIFT(x) ((x) * 4) + +/* CPU has two AHB busses. */ + +/* Global Arbitration0 Control Register */ +#define GLOBAL_ARBITRATION0_CTRL 0x28 + +#define BOOT_CONTROLLER_HIGH_PRIO (1 << 3) +#define DMA_BUS1_HIGH_PRIO (1 << 2) +#define CPU0_HIGH_PRIO (1 << 0) + +/* Global Arbitration1 Control Register */ +#define GLOBAL_ARBITRATION1_CTRL 0x2C + +#define TVE_HIGH_PRIO (1 << 9) +#define PCI_HIGH_PRIO (1 << 8) +#define USB1_HIGH_PRIO (1 << 7) +#define USB0_HIGH_PRIO (1 << 6) +#define GMAC1_HIGH_PRIO (1 << 5) +#define GMAC0_HIGH_PRIO (1 << 4) +#define SECURITY_HIGH_PRIO (1 << 3) +#define RAID_HIGH_PRIO (1 << 2) +#define IDE_HIGH_PRIO (1 << 1) +#define DMA_BUS2_HIGH_PRIO (1 << 0) + +/* Common bits for both arbitration registers */ +#define BURST_LENGTH_SHIFT 16 +#define BURST_LENGTH_MASK (0x3F << 16) + +/* Miscellaneous Control Register */ +#define GLOBAL_MISC_CTRL 0x30 + +#define MEMORY_SPACE_SWAP (1 << 31) +#define USB1_PLUG_MINIB (1 << 30) /* else plug is mini-A */ +#define USB0_PLUG_MINIB (1 << 29) +#define GMAC_GMII (1 << 28) +#define GMAC_1_ENABLE (1 << 27) +/* TODO: define ATA/SATA bits */ +#define USB1_VBUS_ON (1 << 23) +#define USB0_VBUS_ON (1 << 22) +#define APB_CLKOUT_ENABLE (1 << 21) +#define TVC_CLKOUT_ENABLE (1 << 20) +#define EXT_CLKIN_ENABLE (1 << 19) +#define PCI_66MHZ (1 << 18) /* else 33 MHz */ +#define PCI_CLKOUT_ENABLE (1 << 17) +#define LPC_CLKOUT_ENABLE (1 << 16) +#define USB1_WAKEUP_ON (1 << 15) +#define USB0_WAKEUP_ON (1 << 14) +/* TODO: define PCI idle detect bits */ +#define TVC_PADS_ENABLE (1 << 9) +#define SSP_PADS_ENABLE (1 << 8) +#define LCD_PADS_ENABLE (1 << 7) +#define LPC_PADS_ENABLE (1 << 6) +#define PCI_PADS_ENABLE (1 << 5) +#define IDE_PADS_ENABLE (1 << 4) +#define DRAM_PADS_POWER_DOWN (1 << 3) +#define NAND_PADS_DISABLE (1 << 2) +#define PFLASH_PADS_DISABLE (1 << 1) +#define SFLASH_PADS_DISABLE (1 << 0) + +/* Global Clock Control Register */ +#define GLOBAL_CLOCK_CTRL 0x34 + +#define POWER_STATE_G0 (1 << 31) +#define POWER_STATE_S1 (1 << 30) /* else it is S3/S4 state */ +#define SECURITY_APB_AHB (1 << 29) +/* else Security APB clk will be 0.75xAHB */ +/* TODO: TVC clock divider */ +#define PCI_CLKRUN_ENABLE (1 << 16) +#define BOOT_CLK_DISABLE (1 << 13) +#define TVC_CLK_DISABLE (1 << 12) +#define FLASH_CLK_DISABLE (1 << 11) +#define DDR_CLK_DISABLE (1 << 10) +#define PCI_CLK_DISABLE (1 << 9) +#define IDE_CLK_DISABLE (1 << 8) +#define USB1_CLK_DISABLE (1 << 7) +#define USB0_CLK_DISABLE (1 << 6) +#define SATA1_CLK_DISABLE (1 << 5) +#define SATA0_CLK_DISABLE (1 << 4) +#define GMAC1_CLK_DISABLE (1 << 3) +#define GMAC0_CLK_DISABLE (1 << 2) +#define SECURITY_CLK_DISABLE (1 << 1) + +/* TODO: other registers definitions if needed */ + +#endif /* __MACH_GLOBAL_REG_H */ |