diff options
Diffstat (limited to 'Documentation')
3 files changed, 103 insertions, 0 deletions
diff --git a/Documentation/devicetree/bindings/input/ti,drv260x.txt b/Documentation/devicetree/bindings/input/ti,drv260x.txt new file mode 100644 index 000000000000..ee09c8f4474a --- /dev/null +++ b/Documentation/devicetree/bindings/input/ti,drv260x.txt @@ -0,0 +1,50 @@ +* Texas Instruments - drv260x Haptics driver family + +Required properties: + - compatible - One of: + "ti,drv2604" - DRV2604 + "ti,drv2605" - DRV2605 + "ti,drv2605l" - DRV2605L + - reg - I2C slave address + - vbat-supply - Required supply regulator + - mode - Power up mode of the chip (defined in include/dt-bindings/input/ti-drv260x.h) + DRV260X_LRA_MODE - Linear Resonance Actuator mode (Piezoelectric) + DRV260X_LRA_NO_CAL_MODE - This is a LRA Mode but there is no calibration + sequence during init. And the device is configured for real + time playback mode (RTP mode). + DRV260X_ERM_MODE - Eccentric Rotating Mass mode (Rotary vibrator) + - library-sel - These are ROM based waveforms pre-programmed into the IC. + This should be set to set the library to use at power up. + (defined in include/dt-bindings/input/ti-drv260x.h) + DRV260X_LIB_EMPTY - Do not use a pre-programmed library + DRV260X_ERM_LIB_A - Pre-programmed Library + DRV260X_ERM_LIB_B - Pre-programmed Library + DRV260X_ERM_LIB_C - Pre-programmed Library + DRV260X_ERM_LIB_D - Pre-programmed Library + DRV260X_ERM_LIB_E - Pre-programmed Library + DRV260X_ERM_LIB_F - Pre-programmed Library + DRV260X_LIB_LRA - Pre-programmed LRA Library + +Optional properties: + - enable-gpio - gpio pin to enable/disable the device. + - vib-rated-mv - The rated voltage of the actuator in millivolts. + If this is not set then the value will be defaulted to + 3.2 v. + - vib-overdrive-mv - The overdrive voltage of the actuator in millivolts. + If this is not set then the value will be defaulted to + 3.2 v. +Example: + +haptics: haptics@5a { + compatible = "ti,drv2605l"; + reg = <0x5a>; + vbat-supply = <&vbat>; + enable-gpio = <&gpio1 28 GPIO_ACTIVE_HIGH>; + mode = <DRV260X_LRA_MODE>; + library-sel = <DRV260X_LIB_LRA>; + vib-rated-mv = <3200>; + vib-overdriver-mv = <3200>; +} + +For more product information please see the link below: +http://www.ti.com/product/drv2605 diff --git a/Documentation/devicetree/bindings/input/ti,drv2667.txt b/Documentation/devicetree/bindings/input/ti,drv2667.txt new file mode 100644 index 000000000000..996382cf994a --- /dev/null +++ b/Documentation/devicetree/bindings/input/ti,drv2667.txt @@ -0,0 +1,17 @@ +* Texas Instruments - drv2667 Haptics driver + +Required properties: + - compatible - "ti,drv2667" - DRV2667 + - reg - I2C slave address + - vbat-supply - Required supply regulator + +Example: + +haptics: haptics@59 { + compatible = "ti,drv2667"; + reg = <0x59>; + vbat-supply = <&vbat>; +}; + +For more product information please see the link below: +http://www.ti.com/product/drv2667 diff --git a/Documentation/devicetree/bindings/input/ti,palmas-pwrbutton.txt b/Documentation/devicetree/bindings/input/ti,palmas-pwrbutton.txt new file mode 100644 index 000000000000..a3dde8c30e67 --- /dev/null +++ b/Documentation/devicetree/bindings/input/ti,palmas-pwrbutton.txt @@ -0,0 +1,36 @@ +Texas Instruments Palmas family power button module + +This module is part of the Palmas family of PMICs. For more details +about the whole chip see: +Documentation/devicetree/bindings/mfd/palmas.txt. + +This module provides a simple power button event via an Interrupt. + +Required properties: +- compatible: should be one of the following + - "ti,palmas-pwrbutton": For Palmas compatible power on button +- interrupt-parent: Parent interrupt device, must be handle of palmas node. +- interrupts: Interrupt number of power button submodule on device. + +Optional Properties: + +- ti,palmas-long-press-seconds: Duration in seconds which the power + button should be kept pressed for Palmas to power off automatically. + NOTE: This depends on OTP support and POWERHOLD signal configuration + on platform. Valid values are 6, 8, 10 and 12. +- ti,palmas-pwron-debounce-milli-seconds: Duration in milliseconds + which the power button should be kept pressed for Palmas to register + a press for debouncing purposes. NOTE: This depends on specific + Palmas variation capability. Valid values are 15, 100, 500 and 1000. + +Example: + +&palmas { + palmas_pwr_button: pwrbutton { + compatible = "ti,palmas-pwrbutton"; + interrupt-parent = <&tps659038>; + interrupts = <1 IRQ_TYPE_EDGE_FALLING>; + ti,palmas-long-press-seconds = <12>; + ti,palmas-pwron-debounce-milli-seconds = <15>; + }; +}; |