diff options
Diffstat (limited to 'Documentation')
65 files changed, 1522 insertions, 408 deletions
diff --git a/Documentation/ABI/testing/debugfs-hyperv b/Documentation/ABI/testing/debugfs-hyperv new file mode 100644 index 000000000000..9185e1b06bba --- /dev/null +++ b/Documentation/ABI/testing/debugfs-hyperv @@ -0,0 +1,23 @@ +What: /sys/kernel/debug/hyperv/<UUID>/fuzz_test_state +Date: October 2019 +KernelVersion: 5.5 +Contact: Branden Bonaby <brandonbonaby94@gmail.com> +Description: Fuzz testing status of a vmbus device, whether its in an ON + state or a OFF state +Users: Debugging tools + +What: /sys/kernel/debug/hyperv/<UUID>/delay/fuzz_test_buffer_interrupt_delay +Date: October 2019 +KernelVersion: 5.5 +Contact: Branden Bonaby <brandonbonaby94@gmail.com> +Description: Fuzz testing buffer interrupt delay value between 0 - 1000 + microseconds (inclusive). +Users: Debugging tools + +What: /sys/kernel/debug/hyperv/<UUID>/delay/fuzz_test_message_delay +Date: October 2019 +KernelVersion: 5.5 +Contact: Branden Bonaby <brandonbonaby94@gmail.com> +Description: Fuzz testing message delay value between 0 - 1000 microseconds + (inclusive). +Users: Debugging tools diff --git a/Documentation/ABI/testing/ima_policy b/Documentation/ABI/testing/ima_policy index 29ebe9afdac4..29aaedf33246 100644 --- a/Documentation/ABI/testing/ima_policy +++ b/Documentation/ABI/testing/ima_policy @@ -25,6 +25,7 @@ Description: lsm: [[subj_user=] [subj_role=] [subj_type=] [obj_user=] [obj_role=] [obj_type=]] option: [[appraise_type=]] [template=] [permit_directio] + [appraise_flag=] base: func:= [BPRM_CHECK][MMAP_CHECK][CREDS_CHECK][FILE_CHECK][MODULE_CHECK] [FIRMWARE_CHECK] [KEXEC_KERNEL_CHECK] [KEXEC_INITRAMFS_CHECK] @@ -38,6 +39,9 @@ Description: fowner:= decimal value lsm: are LSM specific option: appraise_type:= [imasig] [imasig|modsig] + appraise_flag:= [check_blacklist] + Currently, blacklist check is only for files signed with appended + signature. template:= name of a defined IMA template type (eg, ima-ng). Only valid when action is "measure". pcr:= decimal value diff --git a/Documentation/ABI/testing/sysfs-class-led-driver-el15203000 b/Documentation/ABI/testing/sysfs-class-led-driver-el15203000 new file mode 100644 index 000000000000..f520ece9b64c --- /dev/null +++ b/Documentation/ABI/testing/sysfs-class-led-driver-el15203000 @@ -0,0 +1,139 @@ +What: /sys/class/leds/<led>/hw_pattern +Date: September 2019 +KernelVersion: 5.5 +Description: + Specify a hardware pattern for the EL15203000 LED. + The LEDs board supports only predefined patterns by firmware + for specific LEDs. + + Breathing mode for Screen frame light tube: + "0 4000 1 4000" + + ^ + | + Max-| --- + | / \ + | / \ + | / \ / + | / \ / + Min-|- --- + | + 0------4------8--> time (sec) + + Cascade mode for Pipe LED: + "1 800 2 800 4 800 8 800 16 800" + + ^ + | + 0 On -|----+ +----+ +--- + | | | | | + Off-| +-------------------+ +-------------------+ + | + 1 On -| +----+ +----+ + | | | | | + Off |----+ +-------------------+ +------------------ + | + 2 On -| +----+ +----+ + | | | | | + Off-|---------+ +-------------------+ +------------- + | + 3 On -| +----+ +----+ + | | | | | + Off-|--------------+ +-------------------+ +-------- + | + 4 On -| +----+ +----+ + | | | | | + Off-|-------------------+ +-------------------+ +--- + | + 0---0.8--1.6--2.4--3.2---4---4.8--5.6--6.4--7.2---8--> time (sec) + + Inverted cascade mode for Pipe LED: + "30 800 29 800 27 800 23 800 15 800" + + ^ + | + 0 On -| +-------------------+ +-------------------+ + | | | | | + Off-|----+ +----+ +--- + | + 1 On -|----+ +-------------------+ +------------------ + | | | | | + Off | +----+ +----+ + | + 2 On -|---------+ +-------------------+ +------------- + | | | | | + Off-| +----+ +----+ + | + 3 On -|--------------+ +-------------------+ +-------- + | | | | | + Off-| +----+ +----+ + | + 4 On -|-------------------+ +-------------------+ +--- + | | | | | + Off-| +----+ +----+ + | + 0---0.8--1.6--2.4--3.2---4---4.8--5.6--6.4--7.2---8--> time (sec) + + Bounce mode for Pipe LED: + "1 800 2 800 4 800 8 800 16 800 16 800 8 800 4 800 2 800 1 800" + + ^ + | + 0 On -|----+ +-------- + | | | + Off-| +---------------------------------------+ + | + 1 On -| +----+ +----+ + | | | | | + Off |----+ +-----------------------------+ +-------- + | + 2 On -| +----+ +----+ + | | | | | + Off-|---------+ +-------------------+ +------------- + | + 3 On -| +----+ +----+ + | | | | | + Off-|--------------+ +---------+ +------------------ + | + 4 On -| +---------+ + | | | + Off-|-------------------+ +----------------------- + | + 0---0.8--1.6--2.4--3.2---4---4.8--5.6--6.4--7.2---8--> time (sec) + + Inverted bounce mode for Pipe LED: + "30 800 29 800 27 800 23 800 15 800 15 800 23 800 27 800 29 800 30 800" + + ^ + | + 0 On -| +---------------------------------------+ + | | | + Off-|----+ +-------- + | + 1 On -|----+ +-----------------------------+ +-------- + | | | | | + Off | +----+ +----+ + | + 2 On -|---------+ +-------------------+ +------------- + | | | | | + Off-| +----+ +----+ + | + 3 On -|--------------+ +---------+ +------------------ + | | | | | + Off-| +----+ +----+ + | + 4 On -|-------------------+ +----------------------- + | | | + Off-| +---------+ + | + 0---0.8--1.6--2.4--3.2---4---4.8--5.6--6.4--7.2---8--> time (sec) + +What: /sys/class/leds/<led>/repeat +Date: September 2019 +KernelVersion: 5.5 +Description: + EL15203000 supports only indefinitely patterns, + so this file should always store -1. + + For more info, please see: + Documentation/ABI/testing/sysfs-class-led-trigger-pattern diff --git a/Documentation/ABI/testing/sysfs-class-watchdog b/Documentation/ABI/testing/sysfs-class-watchdog index 675f9b537661..9860a8b2ba75 100644 --- a/Documentation/ABI/testing/sysfs-class-watchdog +++ b/Documentation/ABI/testing/sysfs-class-watchdog @@ -17,8 +17,13 @@ What: /sys/class/watchdog/watchdogn/nowayout Date: August 2015 Contact: Wim Van Sebroeck <wim@iguana.be> Description: - It is a read only file. While reading, it gives '1' if that - device supports nowayout feature else, it gives '0'. + It is a read/write file. While reading, it gives '1' + if the device has the nowayout feature set, otherwise + it gives '0'. Writing a '1' to the file enables the + nowayout feature. Once set, the nowayout feature + cannot be disabled, so writing a '0' either has no + effect (if the feature was already disabled) or + results in a permission error. What: /sys/class/watchdog/watchdogn/state Date: August 2015 diff --git a/Documentation/ABI/testing/sysfs-platform-mellanox-bootctl b/Documentation/ABI/testing/sysfs-platform-mellanox-bootctl new file mode 100644 index 000000000000..c65a80574869 --- /dev/null +++ b/Documentation/ABI/testing/sysfs-platform-mellanox-bootctl @@ -0,0 +1,58 @@ +What: /sys/bus/platform/devices/MLNXBF04:00/driver/lifecycle_state +Date: Oct 2019 +KernelVersion: 5.5 +Contact: "Liming Sun <lsun@mellanox.com>" +Description: + The Life-cycle state of the SoC, which could be one of the + following values. + Production - Production state and can be updated to secure + GA Secured - Secure chip and not able to change state + GA Non-Secured - Non-Secure chip and not able to change state + RMA - Return Merchandise Authorization + +What: /sys/bus/platform/devices/MLNXBF04:00/driver/post_reset_wdog +Date: Oct 2019 +KernelVersion: 5.5 +Contact: "Liming Sun <lsun@mellanox.com>" +Description: + The watchdog setting in seconds for the next booting. It's used + to reboot the chip and recover it to the old state if the new + boot partition fails. + +What: /sys/bus/platform/devices/MLNXBF04:00/driver/reset_action +Date: Oct 2019 +KernelVersion: 5.5 +Contact: "Liming Sun <lsun@mellanox.com>" +Description: + The source of the boot stream for the next reset. It could be + one of the following values. + external - boot from external source (USB or PCIe) + emmc - boot from the onchip eMMC + emmc_legacy - boot from the onchip eMMC in legacy (slow) mode + +What: /sys/bus/platform/devices/MLNXBF04:00/driver/second_reset_action +Date: Oct 2019 +KernelVersion: 5.5 +Contact: "Liming Sun <lsun@mellanox.com>" +Description: + Update the source of the boot stream after next reset. It could + be one of the following values and will be applied after next + reset. + external - boot from external source (USB or PCIe) + emmc - boot from the onchip eMMC + emmc_legacy - boot from the onchip eMMC in legacy (slow) mode + swap_emmc - swap the primary / secondary boot partition + none - cancel the action + +What: /sys/bus/platform/devices/MLNXBF04:00/driver/secure_boot_fuse_state +Date: Oct 2019 +KernelVersion: 5.5 +Contact: "Liming Sun <lsun@mellanox.com>" +Description: + The state of eFuse versions with the following values. + InUse - burnt, valid and currently in use + Used - burnt and valid + Free - not burnt and free to use + Skipped - not burnt but not free (skipped) + Wasted - burnt and invalid + Invalid - not burnt but marked as valid (error state). diff --git a/Documentation/ABI/testing/sysfs-secvar b/Documentation/ABI/testing/sysfs-secvar new file mode 100644 index 000000000000..feebb8c57294 --- /dev/null +++ b/Documentation/ABI/testing/sysfs-secvar @@ -0,0 +1,46 @@ +What: /sys/firmware/secvar +Date: August 2019 +Contact: Nayna Jain <nayna@linux.ibm.com> +Description: This directory is created if the POWER firmware supports OS + secureboot, thereby secure variables. It exposes interface + for reading/writing the secure variables + +What: /sys/firmware/secvar/vars +Date: August 2019 +Contact: Nayna Jain <nayna@linux.ibm.com> +Description: This directory lists all the secure variables that are supported + by the firmware. + +What: /sys/firmware/secvar/format +Date: August 2019 +Contact: Nayna Jain <nayna@linux.ibm.com> +Description: A string indicating which backend is in use by the firmware. + This determines the format of the variable and the accepted + format of variable updates. + +What: /sys/firmware/secvar/vars/<variable name> +Date: August 2019 +Contact: Nayna Jain <nayna@linux.ibm.com> +Description: Each secure variable is represented as a directory named as + <variable_name>. The variable name is unique and is in ASCII + representation. The data and size can be determined by reading + their respective attribute files. + +What: /sys/firmware/secvar/vars/<variable_name>/size +Date: August 2019 +Contact: Nayna Jain <nayna@linux.ibm.com> +Description: An integer representation of the size of the content of the + variable. In other words, it represents the size of the data. + +What: /sys/firmware/secvar/vars/<variable_name>/data +Date: August 2019 +Contact: Nayna Jain h<nayna@linux.ibm.com> +Description: A read-only file containing the value of the variable. The size + of the file represents the maximum size of the variable data. + +What: /sys/firmware/secvar/vars/<variable_name>/update +Date: August 2019 +Contact: Nayna Jain <nayna@linux.ibm.com> +Description: A write-only file that is used to submit the new value for the + variable. The size of the file represents the maximum size of + the variable data that can be written. diff --git a/Documentation/devicetree/bindings/arm/freescale/fsl,scu.txt b/Documentation/devicetree/bindings/arm/freescale/fsl,scu.txt index c149fadc6f47..70c1a624486d 100644 --- a/Documentation/devicetree/bindings/arm/freescale/fsl,scu.txt +++ b/Documentation/devicetree/bindings/arm/freescale/fsl,scu.txt @@ -157,6 +157,15 @@ Required properties: Optional properties: - timeout-sec: contains the watchdog timeout in seconds. +SCU key bindings based on SCU Message Protocol +------------------------------------------------------------ + +Required properties: +- compatible: should be: + "fsl,imx8qxp-sc-key" + followed by "fsl,imx-sc-key"; +- linux,keycodes: See Documentation/devicetree/bindings/input/keys.txt + Example (imx8qxp): ------------- aliases { @@ -220,6 +229,11 @@ firmware { compatible = "fsl,imx8qxp-sc-rtc"; }; + scu_key: scu-key { + compatible = "fsl,imx8qxp-sc-key", "fsl,imx-sc-key"; + linux,keycodes = <KEY_POWER>; + }; + watchdog { compatible = "fsl,imx8qxp-sc-wdt", "fsl,imx-sc-wdt"; timeout-sec = <60>; diff --git a/Documentation/devicetree/bindings/board/fsl-board.txt b/Documentation/devicetree/bindings/board/fsl-board.txt index eb52f6b35159..9cde57015921 100644 --- a/Documentation/devicetree/bindings/board/fsl-board.txt +++ b/Documentation/devicetree/bindings/board/fsl-board.txt @@ -47,36 +47,6 @@ Example (LS2080A-RDB): reg = <0x3 0 0x10000>; }; -* Freescale BCSR GPIO banks - -Some BCSR registers act as simple GPIO controllers, each such -register can be represented by the gpio-controller node. - -Required properities: -- compatible : Should be "fsl,<board>-bcsr-gpio". -- reg : Should contain the address and the length of the GPIO bank - register. -- #gpio-cells : Should be two. The first cell is the pin number and the - second cell is used to specify optional parameters (currently unused). -- gpio-controller : Marks the port as GPIO controller. - -Example: - - bcsr@1,0 { - #address-cells = <1>; - #size-cells = <1>; - compatible = "fsl,mpc8360mds-bcsr"; - reg = <1 0 0x8000>; - ranges = <0 1 0 0x8000>; - - bcsr13: gpio-controller@d { - #gpio-cells = <2>; - compatible = "fsl,mpc8360mds-bcsr-gpio"; - reg = <0xd 1>; - gpio-controller; - }; - }; - * Freescale on-board FPGA connected on I2C bus Some Freescale boards like BSC9132QDS have on board FPGA connected on diff --git a/Documentation/devicetree/bindings/clock/amlogic,axg-audio-clkc.txt b/Documentation/devicetree/bindings/clock/amlogic,axg-audio-clkc.txt index b3957d10d241..3a8948c04bc9 100644 --- a/Documentation/devicetree/bindings/clock/amlogic,axg-audio-clkc.txt +++ b/Documentation/devicetree/bindings/clock/amlogic,axg-audio-clkc.txt @@ -7,7 +7,8 @@ devices. Required Properties: - compatible : should be "amlogic,axg-audio-clkc" for the A113X and A113D, - "amlogic,g12a-audio-clkc" for G12A. + "amlogic,g12a-audio-clkc" for G12A, + "amlogic,sm1-audio-clkc" for S905X3. - reg : physical base address of the clock controller and length of memory mapped region. - clocks : a list of phandle + clock-specifier pairs for the clocks listed diff --git a/Documentation/devicetree/bindings/clock/armada3700-periph-clock.txt b/Documentation/devicetree/bindings/clock/armada3700-periph-clock.txt index 1e3370ba189f..fbf58c443c04 100644 --- a/Documentation/devicetree/bindings/clock/armada3700-periph-clock.txt +++ b/Documentation/devicetree/bindings/clock/armada3700-periph-clock.txt @@ -9,7 +9,7 @@ bridge. The peripheral clock consumer should specify the desired clock by having the clock ID in its "clocks" phandle cell. -The following is a list of provided IDs for Armada 370 North bridge clocks: +The following is a list of provided IDs for Armada 3700 North bridge clocks: ID Clock name Description ----------------------------------- 0 mmc MMC controller @@ -30,7 +30,7 @@ ID Clock name Description 15 eip97 EIP 97 16 cpu CPU -The following is a list of provided IDs for Armada 370 South bridge clocks: +The following is a list of provided IDs for Armada 3700 South bridge clocks: ID Clock name Description ----------------------------------- 0 gbe-50 50 MHz parent clock for Gigabit Ethernet @@ -46,6 +46,7 @@ ID Clock name Description 10 sdio SDIO 11 usb32-sub2-sys USB 2 clock 12 usb32-ss-sys USB 3 clock +13 pcie PCIe controller Required properties: diff --git a/Documentation/devicetree/bindings/clock/bitmain,bm1880-clk.yaml b/Documentation/devicetree/bindings/clock/bitmain,bm1880-clk.yaml new file mode 100644 index 000000000000..e63827399c1a --- /dev/null +++ b/Documentation/devicetree/bindings/clock/bitmain,bm1880-clk.yaml @@ -0,0 +1,76 @@ +# SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause) +%YAML 1.2 +--- +$id: http://devicetree.org/schemas/bindings/clock/bitmain,bm1880-clk.yaml# +$schema: http://devicetree.org/meta-schemas/core.yaml# + +title: Bitmain BM1880 Clock Controller + +maintainers: + - Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org> + +description: | + The Bitmain BM1880 clock controller generates and supplies clock to + various peripherals within the SoC. + + This binding uses common clock bindings + [1] Documentation/devicetree/bindings/clock/clock-bindings.txt + +properties: + compatible: + const: bitmain,bm1880-clk + + reg: + items: + - description: pll registers + - description: system registers + + reg-names: + items: + - const: pll + - const: sys + + clocks: + maxItems: 1 + + clock-names: + const: osc + + '#clock-cells': + const: 1 + +required: + - compatible + - reg + - reg-names + - clocks + - clock-names + - '#clock-cells' + +additionalProperties: false + +examples: + # Clock controller node: + - | + clk: clock-controller@e8 { + compatible = "bitmain,bm1880-clk"; + reg = <0xe8 0x0c>, <0x800 0xb0>; + reg-names = "pll", "sys"; + clocks = <&osc>; + clock-names = "osc"; + #clock-cells = <1>; + }; + + # Example UART controller node that consumes clock generated by the clock controller: + - | + uart0: serial@58018000 { + compatible = "snps,dw-apb-uart"; + reg = <0x0 0x58018000 0x0 0x2000>; + clocks = <&clk 45>, <&clk 46>; + clock-names = "baudclk", "apb_pclk"; + interrupts = <0 9 4>; + reg-shift = <2>; + reg-io-width = <4>; + }; + +... diff --git a/Documentation/devicetree/bindings/clock/imx7ulp-clock.txt b/Documentation/devicetree/bindings/clock/imx7ulp-clock.txt index a4f8cd478f92..93d89adb7afe 100644 --- a/Documentation/devicetree/bindings/clock/imx7ulp-clock.txt +++ b/Documentation/devicetree/bindings/clock/imx7ulp-clock.txt @@ -82,7 +82,6 @@ pcc2: pcc2@403f0000 { <&scg1 IMX7ULP_CLK_APLL_PFD0>, <&scg1 IMX7ULP_CLK_UPLL>, <&scg1 IMX7ULP_CLK_SOSC_BUS_CLK>, - <&scg1 IMX7ULP_CLK_MIPI_PLL>, <&scg1 IMX7ULP_CLK_FIRC_BUS_CLK>, <&scg1 IMX7ULP_CLK_ROSC>, <&scg1 IMX7ULP_CLK_SPLL_BUS_CLK>; diff --git a/Documentation/devicetree/bindings/clock/ingenic,cgu.txt b/Documentation/devicetree/bindings/clock/ingenic,cgu.txt index ba5a442026b7..75598e655067 100644 --- a/Documentation/devicetree/bindings/clock/ingenic,cgu.txt +++ b/Documentation/devicetree/bindings/clock/ingenic,cgu.txt @@ -11,6 +11,7 @@ Required properties: * ingenic,jz4725b-cgu * ingenic,jz4770-cgu * ingenic,jz4780-cgu + * ingenic,x1000-cgu - reg : The address & length of the CGU registers. - clocks : List of phandle & clock specifiers for clocks external to the CGU. Two such external clocks should be specified - first the external crystal diff --git a/Documentation/devicetree/bindings/clock/qcom,gcc.txt b/Documentation/devicetree/bindings/clock/qcom,gcc.txt deleted file mode 100644 index d14362ad4132..000000000000 --- a/Documentation/devicetree/bindings/clock/qcom,gcc.txt +++ /dev/null @@ -1,94 +0,0 @@ -Qualcomm Global Clock & Reset Controller Binding ------------------------------------------------- - -Required properties : -- compatible : shall contain only one of the following: - - "qcom,gcc-apq8064" - "qcom,gcc-apq8084" - "qcom,gcc-ipq8064" - "qcom,gcc-ipq4019" - "qcom,gcc-ipq8074" - "qcom,gcc-msm8660" - "qcom,gcc-msm8916" - "qcom,gcc-msm8960" - "qcom,gcc-msm8974" - "qcom,gcc-msm8974pro" - "qcom,gcc-msm8974pro-ac" - "qcom,gcc-msm8994" - "qcom,gcc-msm8996" - "qcom,gcc-msm8998" - "qcom,gcc-mdm9615" - "qcom,gcc-qcs404" - "qcom,gcc-sdm630" - "qcom,gcc-sdm660" - "qcom,gcc-sdm845" - "qcom,gcc-sm8150" - -- reg : shall contain base register location and length -- #clock-cells : shall contain 1 -- #reset-cells : shall contain 1 - -Optional properties : -- #power-domain-cells : shall contain 1 -- Qualcomm TSENS (thermal sensor device) on some devices can -be part of GCC and hence the TSENS properties can also be -part of the GCC/clock-controller node. -For more details on the TSENS properties please refer -Documentation/devicetree/bindings/thermal/qcom-tsens.txt -- protected-clocks : Protected clock specifier list as per common clock - binding. - -For SM8150 only: - - clocks: a list of phandles and clock-specifier pairs, - one for each entry in clock-names. - - clock-names: "bi_tcxo" (required) - "sleep_clk" (optional) - "aud_ref_clock" (optional) - -Example: - clock-controller@900000 { - compatible = "qcom,gcc-msm8960"; - reg = <0x900000 0x4000>; - #clock-cells = <1>; - #reset-cells = <1>; - #power-domain-cells = <1>; - }; - -Example of GCC with TSENS properties: - clock-controller@900000 { - compatible = "qcom,gcc-apq8064"; - reg = <0x00900000 0x4000>; - nvmem-cells = <&tsens_calib>, <&tsens_backup>; - nvmem-cell-names = "calib", "calib_backup"; - #clock-cells = <1>; - #reset-cells = <1>; - #thermal-sensor-cells = <1>; - }; - -Example of GCC with protected-clocks properties: - clock-controller@100000 { - compatible = "qcom,gcc-sdm845"; - reg = <0x100000 0x1f0000>; - #clock-cells = <1>; - #reset-cells = <1>; - #power-domain-cells = <1>; - protected-clocks = <GCC_QSPI_CORE_CLK>, - <GCC_QSPI_CORE_CLK_SRC>, - <GCC_QSPI_CNOC_PERIPH_AHB_CLK>, - <GCC_LPASS_Q6_AXI_CLK>, - <GCC_LPASS_SWAY_CLK>; - }; - -Example of GCC with clocks - gcc: clock-controller@100000 { - compatible = "qcom,gcc-sm8150"; - reg = <0x00100000 0x1f0000>; - #clock-cells = <1>; - #reset-cells = <1>; - #power-domain-cells = <1>; - clock-names = "bi_tcxo", - "sleep_clk"; - clocks = <&rpmcc RPM_SMD_XO_CLK_SRC>, - <&sleep_clk>; - }; diff --git a/Documentation/devicetree/bindings/clock/qcom,gcc.yaml b/Documentation/devicetree/bindings/clock/qcom,gcc.yaml new file mode 100644 index 000000000000..e73a56fb60ca --- /dev/null +++ b/Documentation/devicetree/bindings/clock/qcom,gcc.yaml @@ -0,0 +1,188 @@ +# SPDX-License-Identifier: GPL-2.0-only +%YAML 1.2 +--- +$id: http://devicetree.org/schemas/bindings/clock/qcom,gcc.yaml# +$schema: http://devicetree.org/meta-schemas/core.yaml# + +title: Qualcomm Global Clock & Reset Controller Binding + +maintainers: + - Stephen Boyd <sboyd@kernel.org> + - Taniya Das <tdas@codeaurora.org> + +description: | + Qualcomm global clock control module which supports the clocks, resets and + power domains. + +properties: + compatible : + enum: + - qcom,gcc-apq8064 + - qcom,gcc-apq8084 + - qcom,gcc-ipq8064 + - qcom,gcc-ipq4019 + - qcom,gcc-ipq8074 + - qcom,gcc-msm8660 + - qcom,gcc-msm8916 + - qcom,gcc-msm8960 + - qcom,gcc-msm8974 + - qcom,gcc-msm8974pro + - qcom,gcc-msm8974pro-ac + - qcom,gcc-msm8994 + - qcom,gcc-msm8996 + - qcom,gcc-msm8998 + - qcom,gcc-mdm9615 + - qcom,gcc-qcs404 + - qcom,gcc-sc7180 + - qcom,gcc-sdm630 + - qcom,gcc-sdm660 + - qcom,gcc-sdm845 + - qcom,gcc-sm8150 + + clocks: + minItems: 1 + maxItems: 3 + items: + - description: Board XO source + - description: Board active XO source + - description: Sleep clock source + + clock-names: + minItems: 1 + maxItems: 3 + items: + - const: bi_tcxo + - const: bi_tcxo_ao + - const: sleep_clk + + '#clock-cells': + const: 1 + + '#reset-cells': + const: 1 + + '#power-domain-cells': + const: 1 + + reg: + maxItems: 1 + + nvmem-cells: + minItems: 1 + maxItems: 2 + description: + Qualcomm TSENS (thermal sensor device) on some devices can + be part of GCC and hence the TSENS properties can also be part + of the GCC/clock-controller node. + For more details on the TSENS properties please refer + Documentation/devicetree/bindings/thermal/qcom-tsens.txt + + nvmem-cell-names: + minItems: 1 + maxItems: 2 + description: + Names for each nvmem-cells specified. + items: + - const: calib + - const: calib_backup + + 'thermal-sensor-cells': + const: 1 + + protected-clocks: + description: + Protected clock specifier list as per common clock binding + +required: + - compatible + - reg + - '#clock-cells' + - '#reset-cells' + - '#power-domain-cells' + +if: + properties: + compatible: + contains: + const: qcom,gcc-apq8064 + +then: + required: + - nvmem-cells + - nvmem-cell-names + - '#thermal-sensor-cells' + +else: + if: + properties: + compatible: + contains: + enum: + - qcom,gcc-sm8150 + - qcom,gcc-sc7180 + then: + required: + - clocks + - clock-names + + +examples: + # Example for GCC for MSM8960: + - | + clock-controller@900000 { + compatible = "qcom,gcc-msm8960"; + reg = <0x900000 0x4000>; + #clock-cells = <1>; + #reset-cells = <1>; + #power-domain-cells = <1>; + }; + + + # Example of GCC with TSENS properties: + - | + clock-controller@900000 { + compatible = "qcom,gcc-apq8064"; + reg = <0x00900000 0x4000>; + nvmem-cells = <&tsens_calib>, <&tsens_backup>; + nvmem-cell-names = "calib", "calib_backup"; + #clock-cells = <1>; + #reset-cells = <1>; + #power-domain-cells = <1>; + #thermal-sensor-cells = <1>; + }; + + # Example of GCC with protected-clocks properties: + - | + clock-controller@100000 { + compatible = "qcom,gcc-sdm845"; + reg = <0x100000 0x1f0000>; + protected-clocks = <187>, <188>, <189>, <190>, <191>; + #clock-cells = <1>; + #reset-cells = <1>; + #power-domain-cells = <1>; + }; + + # Example of GCC with clock node properties for SM8150: + - | + clock-controller@100000 { + compatible = "qcom,gcc-sm8150"; + reg = <0x00100000 0x1f0000>; + clocks = <&rpmhcc 0>, <&rpmhcc 1>, <&sleep_clk>; + clock-names = "bi_tcxo", "bi_tcxo_ao", "sleep_clk"; + #clock-cells = <1>; + #reset-cells = <1>; + #power-domain-cells = <1>; + }; + + # Example of GCC with clock nodes properties for SC7180: + - | + clock-controller@100000 { + compatible = "qcom,gcc-sc7180"; + reg = <0x100000 0x1f0000>; + clocks = <&rpmhcc 0>, <&rpmhcc 1>; + clock-names = "bi_tcxo", "bi_tcxo_ao"; + #clock-cells = <1>; + #reset-cells = <1>; + #power-domain-cells = <1>; + }; +... diff --git a/Documentation/devicetree/bindings/clock/qcom,q6sstopcc.yaml b/Documentation/devicetree/bindings/clock/qcom,q6sstopcc.yaml new file mode 100644 index 000000000000..bbaaf1e2a203 --- /dev/null +++ b/Documentation/devicetree/bindings/clock/qcom,q6sstopcc.yaml @@ -0,0 +1,43 @@ +# SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause) +%YAML 1.2 +--- +$id: http://devicetree.org/schemas/clock/qcom,q6sstopcc.yaml# +$schema: http://devicetree.org/meta-schemas/core.yaml# + +title: Q6SSTOP clock Controller + +maintainers: + - Govind Singh <govinds@codeaurora.org> + +properties: + compatible: + const: "qcom,qcs404-q6sstopcc" + + reg: + items: + - description: Q6SSTOP clocks register region + - description: Q6SSTOP_TCSR register region + + clocks: + items: + - description: ahb clock for the q6sstopCC + + '#clock-cells': + const: 1 + +required: + - compatible + - reg + - clocks + - '#clock-cells' + +additionalProperties: false + +examples: + - | + q6sstopcc: clock-controller@7500000 { + compatible = "qcom,qcs404-q6sstopcc"; + reg = <0x07500000 0x4e000>, <0x07550000 0x10000>; + clocks = <&gcc 141>; + #clock-cells = <1>; + }; diff --git a/Documentation/devicetree/bindings/clock/qcom,rpmh-clk.txt b/Documentation/devicetree/bindings/clock/qcom,rpmh-clk.txt deleted file mode 100644 index 365bbde599b1..000000000000 --- a/Documentation/devicetree/bindings/clock/qcom,rpmh-clk.txt +++ /dev/null @@ -1,27 +0,0 @@ -Qualcomm Technologies, Inc. RPMh Clocks -------------------------------------------------------- - -Resource Power Manager Hardened (RPMh) manages shared resources on -some Qualcomm Technologies Inc. SoCs. It accepts clock requests from -other hardware subsystems via RSC to control clocks. - -Required properties : -- compatible : must be one of: - "qcom,sdm845-rpmh-clk" - "qcom,sm8150-rpmh-clk" - -- #clock-cells : must contain 1 -- clocks: a list of phandles and clock-specifier pairs, - one for each entry in clock-names. -- clock-names: Parent board clock: "xo". - -Example : - -#include <dt-bindings/clock/qcom,rpmh.h> - - &apps_rsc { - rpmhcc: clock-controller { - compatible = "qcom,sdm845-rpmh-clk"; - #clock-cells = <1>; - }; - }; diff --git a/Documentation/devicetree/bindings/clock/qcom,rpmhcc.yaml b/Documentation/devicetree/bindings/clock/qcom,rpmhcc.yaml new file mode 100644 index 000000000000..94e2f14eb967 --- /dev/null +++ b/Documentation/devicetree/bindings/clock/qcom,rpmhcc.yaml @@ -0,0 +1,49 @@ +# SPDX-License-Identifier: GPL-2.0-only +%YAML 1.2 +--- +$id: http://devicetree.org/schemas/bindings/clock/qcom,rpmhcc.yaml# +$schema: http://devicetree.org/meta-schemas/core.yaml# + +title: Qualcomm Technologies, Inc. RPMh Clocks Bindings + +maintainers: + - Taniya Das <tdas@codeaurora.org> + +description: | + Resource Power Manager Hardened (RPMh) manages shared resources on + some Qualcomm Technologies Inc. SoCs. It accepts clock requests from + other hardware subsystems via RSC to control clocks. + +properties: + compatible: + enum: + - qcom,sc7180-rpmh-clk + - qcom,sdm845-rpmh-clk + - qcom,sm8150-rpmh-clk + + clocks: + maxItems: 1 + + clock-names: + items: + - const: xo + + '#clock-cells': + const: 1 + +required: + - compatible + - '#clock-cells' + +examples: + # Example for GCC for SDM845: The below node should be defined inside + # &apps_rsc node. + - | + #include <dt-bindings/clock/qcom,rpmh.h> + rpmhcc: clock-controller { + compatible = "qcom,sdm845-rpmh-clk"; + clocks = <&xo_board>; + clock-names = "xo"; + #clock-cells = <1>; + }; +... diff --git a/Documentation/devicetree/bindings/clock/renesas,cpg-mssr.txt b/Documentation/devicetree/bindings/clock/renesas,cpg-mssr.txt index 916a601b76a7..d67f57e0dfd2 100644 --- a/Documentation/devicetree/bindings/clock/renesas,cpg-mssr.txt +++ b/Documentation/devicetree/bindings/clock/renesas,cpg-mssr.txt @@ -19,6 +19,7 @@ Required Properties: - "renesas,r8a7745-cpg-mssr" for the r8a7745 SoC (RZ/G1E) - "renesas,r8a77470-cpg-mssr" for the r8a77470 SoC (RZ/G1C) - "renesas,r8a774a1-cpg-mssr" for the r8a774a1 SoC (RZ/G2M) + - "renesas,r8a774b1-cpg-mssr" for the r8a774a1 SoC (RZ/G2N) - "renesas,r8a774c0-cpg-mssr" for the r8a774c0 SoC (RZ/G2E) - "renesas,r8a7790-cpg-mssr" for the r8a7790 SoC (R-Car H2) - "renesas,r8a7791-cpg-mssr" for the r8a7791 SoC (R-Car M2-W) @@ -26,7 +27,8 @@ Required Properties: - "renesas,r8a7793-cpg-mssr" for the r8a7793 SoC (R-Car M2-N) - "renesas,r8a7794-cpg-mssr" for the r8a7794 SoC (R-Car E2) - "renesas,r8a7795-cpg-mssr" for the r8a7795 SoC (R-Car H3) - - "renesas,r8a7796-cpg-mssr" for the r8a7796 SoC (R-Car M3-W) + - "renesas,r8a7796-cpg-mssr" for the r8a77960 SoC (R-Car M3-W) + - "renesas,r8a77961-cpg-mssr" for the r8a77961 SoC (R-Car M3-W+) - "renesas,r8a77965-cpg-mssr" for the r8a77965 SoC (R-Car M3-N) - "renesas,r8a77970-cpg-mssr" for the r8a77970 SoC (R-Car V3M) - "renesas,r8a77980-cpg-mssr" for the r8a77980 SoC (R-Car V3H) @@ -40,10 +42,11 @@ Required Properties: clock-names - clock-names: List of external parent clock names. Valid names are: - "extal" (r7s9210, r8a7743, r8a7744, r8a7745, r8a77470, r8a774a1, - r8a774c0, r8a7790, r8a7791, r8a7792, r8a7793, r8a7794, - r8a7795, r8a7796, r8a77965, r8a77970, r8a77980, r8a77990, - r8a77995) - - "extalr" (r8a774a1, r8a7795, r8a7796, r8a77965, r8a77970, r8a77980) + r8a774b1, r8a774c0, r8a7790, r8a7791, r8a7792, r8a7793, + r8a7794, r8a7795, r8a77960, r8a77961, r8a77965, r8a77970, + r8a77980, r8a77990, r8a77995) + - "extalr" (r8a774a1, r8a774b1, r8a7795, r8a77960, r8a77961, r8a77965, + r8a77970, r8a77980) - "usb_extal" (r8a7743, r8a7744, r8a7745, r8a77470, r8a7790, r8a7791, r8a7793, r8a7794) diff --git a/Documentation/devicetree/bindings/clock/renesas,rcar-gen2-cpg-clocks.txt b/Documentation/devicetree/bindings/clock/renesas,rcar-gen2-cpg-clocks.txt deleted file mode 100644 index f8c05bb4116e..000000000000 --- a/Documentation/devicetree/bindings/clock/renesas,rcar-gen2-cpg-clocks.txt +++ /dev/null @@ -1,60 +0,0 @@ -* Renesas R-Car Gen2 Clock Pulse Generator (CPG) - -The CPG generates core clocks for the R-Car Gen2 SoCs. It includes three PLLs -and several fixed ratio dividers. -The CPG also provides a Clock Domain for SoC devices, in combination with the -CPG Module Stop (MSTP) Clocks. - -Required Properties: - - - compatible: Must be one of - - "renesas,r8a7790-cpg-clocks" for the r8a7790 CPG - - "renesas,r8a7791-cpg-clocks" for the r8a7791 CPG - - "renesas,r8a7792-cpg-clocks" for the r8a7792 CPG - - "renesas,r8a7793-cpg-clocks" for the r8a7793 CPG - - "renesas,r8a7794-cpg-clocks" for the r8a7794 CPG - and "renesas,rcar-gen2-cpg-clocks" as a fallback. - - - reg: Base address and length of the memory resource used by the CPG - - - clocks: References to the parent clocks: first to the EXTAL clock, second - to the USB_EXTAL clock - - #clock-cells: Must be 1 - - clock-output-names: The names of the clocks. Supported clocks are "main", - "pll0", "pll1", "pll3", "lb", "qspi", "sdh", "sd0", "sd1", "z", "rcan", and - "adsp" - - #power-domain-cells: Must be 0 - -SoC devices that are part of the CPG/MSTP Clock Domain and can be power-managed -through an MSTP clock should refer to the CPG device node in their -"power-domains" property, as documented by the generic PM domain bindings in -Documentation/devicetree/bindings/power/power_domain.txt. - - -Examples --------- - - - CPG device node: - - cpg_clocks: cpg_clocks@e6150000 { - compatible = "renesas,r8a7790-cpg-clocks", - "renesas,rcar-gen2-cpg-clocks"; - reg = <0 0xe6150000 0 0x1000>; - clocks = <&extal_clk &usb_extal_clk>; - #clock-cells = <1>; - clock-output-names = "main", "pll0, "pll1", "pll3", - "lb", "qspi", "sdh", "sd0", "sd1", "z", - "rcan", "adsp"; - #power-domain-cells = <0>; - }; - - - - CPG/MSTP Clock Domain member device node: - - thermal@e61f0000 { - compatible = "renesas,thermal-r8a7790", "renesas,rcar-thermal"; - reg = <0 0xe61f0000 0 0x14>, <0 0xe61f0100 0 0x38>; - interrupts = <0 69 IRQ_TYPE_LEVEL_HIGH>; - clocks = <&mstp5_clks R8A7790_CLK_THERMAL>; - power-domains = <&cpg_clocks>; - }; diff --git a/Documentation/devicetree/bindings/clock/renesas,rcar-usb2-clock-sel.txt b/Documentation/devicetree/bindings/clock/renesas,rcar-usb2-clock-sel.txt index e96e085271c1..83f6c6a7c41c 100644 --- a/Documentation/devicetree/bindings/clock/renesas,rcar-usb2-clock-sel.txt +++ b/Documentation/devicetree/bindings/clock/renesas,rcar-usb2-clock-sel.txt @@ -46,7 +46,7 @@ Required properties: Example (R-Car H3): usb2_clksel: clock-controller@e6590630 { - compatible = "renesas,r8a77950-rcar-usb2-clock-sel", + compatible = "renesas,r8a7795-rcar-usb2-clock-sel", "renesas,rcar-gen3-usb2-clock-sel"; reg = <0 0xe6590630 0 0x02>; clocks = <&cpg CPG_MOD 703>, <&usb_extal>, <&usb_xtal>; diff --git a/Documentation/devicetree/bindings/gpio/brcm,xgs-iproc-gpio.yaml b/Documentation/devicetree/bindings/gpio/brcm,xgs-iproc-gpio.yaml new file mode 100644 index 000000000000..64e279a4bc10 --- /dev/null +++ b/Documentation/devicetree/bindings/gpio/brcm,xgs-iproc-gpio.yaml @@ -0,0 +1,70 @@ +# SPDX-License-Identifier: (GPL-2.0 OR BSD-2-Clause) +%YAML 1.2 +--- +$id: http://devicetree.org/schemas/gpio/brcm,xgs-iproc-gpio.yaml# +$schema: http://devicetree.org/meta-schemas/core.yaml# + +title: Broadcom XGS iProc GPIO controller + +maintainers: + - Chris Packham <chris.packham@alliedtelesis.co.nz> + +description: | + This controller is the Chip Common A GPIO present on a number of Broadcom + switch ASICs with integrated SoCs. + +properties: + compatible: + const: brcm,iproc-gpio-cca + + reg: + items: + - description: the I/O address containing the GPIO controller + registers. + - description: the I/O address containing the Chip Common A interrupt + registers. + + gpio-controller: true + + '#gpio-cells': + const: 2 + + ngpios: + minimum: 0 + maximum: 32 + + interrupt-controller: true + + '#interrupt-cells': + const: 2 + + interrupts: + maxItems: 1 + +required: + - compatible + - reg + - "#gpio-cells" + - gpio-controller + +dependencies: + interrupt-controller: [ interrupts ] + +examples: + - | + #include <dt-bindings/interrupt-controller/irq.h> + #include <dt-bindings/interrupt-controller/arm-gic.h> + gpio@18000060 { + compatible = "brcm,iproc-gpio-cca"; + #gpio-cells = <2>; + reg = <0x18000060 0x50>, + <0x18000000 0x50>; + ngpios = <12>; + gpio-controller; + interrupt-controller; + #interrupt-cells = <2>; + interrupts = <GIC_SPI 91 IRQ_TYPE_LEVEL_HIGH>; + }; + + +... diff --git a/Documentation/devicetree/bindings/gpio/gpio-rda.yaml b/Documentation/devicetree/bindings/gpio/gpio-rda.yaml new file mode 100644 index 000000000000..6ece555f074f --- /dev/null +++ b/Documentation/devicetree/bindings/gpio/gpio-rda.yaml @@ -0,0 +1,50 @@ +# SPDX-License-Identifier: (GPL-2.0 OR BSD-2-Clause) +%YAML 1.2 +--- +$id: http://devicetree.org/schemas/gpio/gpio-rda.yaml# +$schema: http://devicetree.org/meta-schemas/core.yaml# + +title: RDA Micro GPIO controller + +maintainers: + - Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org> + +properties: + compatible: + const: rda,8810pl-gpio + + reg: + maxItems: 1 + + gpio-controller: true + + "#gpio-cells": + const: 2 + + ngpios: + description: + Number of available gpios in a bank. + minimum: 1 + maximum: 32 + + interrupt-controller: true + + "#interrupt-cells": + const: 2 + + interrupts: + maxItems: 1 + +required: + - compatible + - reg + - gpio-controller + - "#gpio-cells" + - ngpios + - interrupt-controller + - "#interrupt-cells" + - interrupts + +additionalProperties: false + +... diff --git a/Documentation/devicetree/bindings/gpio/renesas,gpio-rcar.txt b/Documentation/devicetree/bindings/gpio/renesas,gpio-rcar.txt index f3f2c468c1b6..41e5fed0f842 100644 --- a/Documentation/devicetree/bindings/gpio/renesas,gpio-rcar.txt +++ b/Documentation/devicetree/bindings/gpio/renesas,gpio-rcar.txt @@ -8,6 +8,7 @@ Required Properties: - "renesas,gpio-r8a7745": for R8A7745 (RZ/G1E) compatible GPIO controller. - "renesas,gpio-r8a77470": for R8A77470 (RZ/G1C) compatible GPIO controller. - "renesas,gpio-r8a774a1": for R8A774A1 (RZ/G2M) compatible GPIO controller. + - "renesas,gpio-r8a774b1": for R8A774B1 (RZ/G2N) compatible GPIO controller. - "renesas,gpio-r8a774c0": for R8A774C0 (RZ/G2E) compatible GPIO controller. - "renesas,gpio-r8a7778": for R8A7778 (R-Car M1) compatible GPIO controller. - "renesas,gpio-r8a7779": for R8A7779 (R-Car H1) compatible GPIO controller. diff --git a/Documentation/devicetree/bindings/i2c/amlogic,meson6-i2c.yaml b/Documentation/devicetree/bindings/i2c/amlogic,meson6-i2c.yaml new file mode 100644 index 000000000000..49cad273c8e5 --- /dev/null +++ b/Documentation/devicetree/bindings/i2c/amlogic,meson6-i2c.yaml @@ -0,0 +1,53 @@ +# SPDX-License-Identifier: (GPL-2.0 OR BSD-2-Clause) +# Copyright 2019 BayLibre, SAS +%YAML 1.2 +--- +$id: "http://devicetree.org/schemas/i2c/amlogic,meson6-i2c.yaml#" +$schema: "http://devicetree.org/meta-schemas/core.yaml#" + +title: Amlogic Meson I2C Controller + +maintainers: + - Neil Armstrong <narmstrong@baylibre.com> + - Beniamino Galvani <b.galvani@gmail.com> + +allOf: + - $ref: /schemas/i2c/i2c-controller.yaml# + +properties: + compatible: + enum: + - amlogic,meson6-i2c # Meson6, Meson8 and compatible SoCs + - amlogic,meson-gxbb-i2c # GXBB and compatible SoCs + - amlogic,meson-axg-i2c # AXG and compatible SoCs + + reg: + maxItems: 1 + + interrupts: + maxItems: 1 + + clocks: + minItems: 1 + +required: + - compatible + - reg + - interrupts + - clocks + +examples: + - | + i2c@c8100500 { + compatible = "amlogic,meson6-i2c"; + reg = <0xc8100500 0x20>; + interrupts = <92>; + clocks = <&clk81>; + #address-cells = <1>; + #size-cells = <0>; + + eeprom@52 { + compatible = "atmel,24c32"; + reg = <0x52>; + }; + }; diff --git a/Documentation/devicetree/bindings/i2c/i2c-aspeed.txt b/Documentation/devicetree/bindings/i2c/i2c-aspeed.txt index 8fbd8633a387..b47f6ccb196a 100644 --- a/Documentation/devicetree/bindings/i2c/i2c-aspeed.txt +++ b/Documentation/devicetree/bindings/i2c/i2c-aspeed.txt @@ -1,4 +1,4 @@ -Device tree configuration for the I2C busses on the AST24XX and AST25XX SoCs. +Device tree configuration for the I2C busses on the AST24XX, AST25XX, and AST26XX SoCs. Required Properties: - #address-cells : should be 1 @@ -6,6 +6,7 @@ Required Properties: - reg : address offset and range of bus - compatible : should be "aspeed,ast2400-i2c-bus" or "aspeed,ast2500-i2c-bus" + or "aspeed,ast2600-i2c-bus" - clocks : root clock of bus, should reference the APB clock in the second cell - resets : phandle to reset controller with the reset number in diff --git a/Documentation/devicetree/bindings/i2c/i2c-at91.txt b/Documentation/devicetree/bindings/i2c/i2c-at91.txt index b7cec17c3daf..2210f4359c45 100644 --- a/Documentation/devicetree/bindings/i2c/i2c-at91.txt +++ b/Documentation/devicetree/bindings/i2c/i2c-at91.txt @@ -3,7 +3,8 @@ I2C for Atmel platforms Required properties : - compatible : Must be "atmel,at91rm9200-i2c", "atmel,at91sam9261-i2c", "atmel,at91sam9260-i2c", "atmel,at91sam9g20-i2c", "atmel,at91sam9g10-i2c", - "atmel,at91sam9x5-i2c", "atmel,sama5d4-i2c" or "atmel,sama5d2-i2c" + "atmel,at91sam9x5-i2c", "atmel,sama5d4-i2c", "atmel,sama5d2-i2c" or + "microchip,sam9x60-i2c" - reg: physical base address of the controller and length of memory mapped region. - interrupts: interrupt number to the cpu. diff --git a/Documentation/devicetree/bindings/i2c/i2c-meson.txt b/Documentation/devicetree/bindings/i2c/i2c-meson.txt deleted file mode 100644 index 13d410de077c..000000000000 --- a/Documentation/devicetree/bindings/i2c/i2c-meson.txt +++ /dev/null @@ -1,30 +0,0 @@ -Amlogic Meson I2C controller - -Required properties: - - compatible: must be: - "amlogic,meson6-i2c" for Meson8 and compatible SoCs - "amlogic,meson-gxbb-i2c" for GXBB and compatible SoCs - "amlogic,meson-axg-i2c"for AXG and compatible SoCs - - - reg: physical address and length of the device registers - - interrupts: a single interrupt specifier - - clocks: clock for the device - - #address-cells: should be <1> - - #size-cells: should be <0> - -For details regarding the following core I2C bindings see also i2c.txt. - -Optional properties: -- clock-frequency: the desired I2C bus clock frequency in Hz; in - absence of this property the default value is used (100 kHz). - -Examples: - - i2c@c8100500 { - compatible = "amlogic,meson6-i2c"; - reg = <0xc8100500 0x20>; - interrupts = <0 92 1>; - clocks = <&clk81>; - #address-cells = <1>; - #size-cells = <0>; - }; diff --git a/Documentation/devicetree/bindings/i2c/i2c.txt b/Documentation/devicetree/bindings/i2c/i2c.txt index 44efafdfd7f5..9a53df4243c6 100644 --- a/Documentation/devicetree/bindings/i2c/i2c.txt +++ b/Documentation/devicetree/bindings/i2c/i2c.txt @@ -55,6 +55,24 @@ wants to support one of the below features, it should adapt the bindings below. Number of nanoseconds the SDA signal takes to fall; t(f) in the I2C specification. +- i2c-analog-filter + Enable analog filter for i2c lines. + +- i2c-digital-filter + Enable digital filter for i2c lines. + +- i2c-digital-filter-width-ns + Width of spikes which can be filtered by digital filter + (i2c-digital-filter). This width is specified in nanoseconds. + +- i2c-analog-filter-cutoff-frequency + Frequency that the analog filter (i2c-analog-filter) uses to distinguish + which signal to filter. Signal with higher frequency than specified will + be filtered out. Only lower frequency will pass (this is applicable to + a low-pass analog filter). Typical value should be above the normal + i2c bus clock frequency (clock-frequency). + Specified in Hz. + - interrupts interrupts used by the device. diff --git a/Documentation/devicetree/bindings/i2c/renesas,i2c.txt b/Documentation/devicetree/bindings/i2c/renesas,i2c.txt index 3ee5e8f6ee01..0660a3eb2547 100644 --- a/Documentation/devicetree/bindings/i2c/renesas,i2c.txt +++ b/Documentation/devicetree/bindings/i2c/renesas,i2c.txt @@ -7,6 +7,7 @@ Required properties: "renesas,i2c-r8a7745" if the device is a part of a R8A7745 SoC. "renesas,i2c-r8a77470" if the device is a part of a R8A77470 SoC. "renesas,i2c-r8a774a1" if the device is a part of a R8A774A1 SoC. + "renesas,i2c-r8a774b1" if the device is a part of a R8A774B1 SoC. "renesas,i2c-r8a774c0" if the device is a part of a R8A774C0 SoC. "renesas,i2c-r8a7778" if the device is a part of a R8A7778 SoC. "renesas,i2c-r8a7779" if the device is a part of a R8A7779 SoC. diff --git a/Documentation/devicetree/bindings/i2c/renesas,iic.txt b/Documentation/devicetree/bindings/i2c/renesas,iic.txt index 202602e6e837..64d11ffb07c4 100644 --- a/Documentation/devicetree/bindings/i2c/renesas,iic.txt +++ b/Documentation/devicetree/bindings/i2c/renesas,iic.txt @@ -8,6 +8,7 @@ Required properties: - "renesas,iic-r8a7744" (RZ/G1N) - "renesas,iic-r8a7745" (RZ/G1E) - "renesas,iic-r8a774a1" (RZ/G2M) + - "renesas,iic-r8a774b1" (RZ/G2N) - "renesas,iic-r8a774c0" (RZ/G2E) - "renesas,iic-r8a7790" (R-Car H2) - "renesas,iic-r8a7791" (R-Car M2-W) diff --git a/Documentation/devicetree/bindings/input/fsl,mpr121-touchkey.yaml b/Documentation/devicetree/bindings/input/fsl,mpr121-touchkey.yaml new file mode 100644 index 000000000000..5b37be0be4e9 --- /dev/null +++ b/Documentation/devicetree/bindings/input/fsl,mpr121-touchkey.yaml @@ -0,0 +1,89 @@ +# SPDX-License-Identifier: (GPL-2.0 OR BSD-2-Clause) +%YAML 1.2 +--- +$id: http://devicetree.org/schemas/input/fsl,mpr121-touchkey.yaml# +$schema: http://devicetree.org/meta-schemas/core.yaml# + +title: Freescale MPR121 capacitive touch sensor controller + +maintainers: + - Dmitry Torokhov <dmitry.torokhov@gmail.com> + +description: | + The MPR121 supports up to 12 completely independent electrodes/capacitance + sensing inputs in which 8 are multifunctional for LED driving and GPIO. + https://www.nxp.com/docs/en/data-sheet/MPR121.pdf + +allOf: + - $ref: input.yaml# + +anyOf: + - required: [ interrupts ] + - required: [ poll-interval ] + +properties: + compatible: + const: fsl,mpr121-touchkey + + reg: + maxItems: 1 + + interrupts: + maxItems: 1 + + vdd-supply: + maxItems: 1 + + linux,keycodes: + minItems: 1 + maxItems: 12 + + wakeup-source: + description: Use any event on keypad as wakeup event. + type: boolean + +required: + - compatible + - reg + - vdd-supply + - linux,keycodes + +examples: + - | + // Example with interrupts + #include "dt-bindings/input/input.h" + i2c { + #address-cells = <1>; + #size-cells = <0>; + + mpr121@5a { + compatible = "fsl,mpr121-touchkey"; + reg = <0x5a>; + interrupt-parent = <&gpio1>; + interrupts = <28 2>; + autorepeat; + vdd-supply = <&ldo4_reg>; + linux,keycodes = <KEY_0>, <KEY_1>, <KEY_2>, <KEY_3>, + <KEY_4>, <KEY_5>, <KEY_6>, <KEY_7>, + <KEY_8>, <KEY_9>, <KEY_A>, <KEY_B>; + }; + }; + + - | + // Example with polling + #include "dt-bindings/input/input.h" + i2c { + #address-cells = <1>; + #size-cells = <0>; + + mpr121@5a { + compatible = "fsl,mpr121-touchkey"; + reg = <0x5a>; + poll-interval = <20>; + autorepeat; + vdd-supply = <&ldo4_reg>; + linux,keycodes = <KEY_0>, <KEY_1>, <KEY_2>, <KEY_3>, + <KEY_4>, <KEY_5>, <KEY_6>, <KEY_7>, + <KEY_8>, <KEY_9>, <KEY_A>, <KEY_B>; + }; + }; diff --git a/Documentation/devicetree/bindings/input/ilitek,ili2xxx.txt b/Documentation/devicetree/bindings/input/ilitek,ili2xxx.txt index b2a76301e632..dc194b2c151a 100644 --- a/Documentation/devicetree/bindings/input/ilitek,ili2xxx.txt +++ b/Documentation/devicetree/bindings/input/ilitek,ili2xxx.txt @@ -1,8 +1,9 @@ -Ilitek ILI210x/ILI251x touchscreen controller +Ilitek ILI210x/ILI2117/ILI251x touchscreen controller Required properties: - compatible: ilitek,ili210x for ILI210x + ilitek,ili2117 for ILI2117 ilitek,ili251x for ILI251x - reg: The I2C address of the device diff --git a/Documentation/devicetree/bindings/input/input.yaml b/Documentation/devicetree/bindings/input/input.yaml new file mode 100644 index 000000000000..6d519046b3af --- /dev/null +++ b/Documentation/devicetree/bindings/input/input.yaml @@ -0,0 +1,36 @@ +# SPDX-License-Identifier: (GPL-2.0 OR BSD-2-Clause) +%YAML 1.2 +--- +$id: http://devicetree.org/schemas/input/input.yaml# +$schema: http://devicetree.org/meta-schemas/core.yaml# + +title: Common input schema binding + +maintainers: + - Dmitry Torokhov <dmitry.torokhov@gmail.com> + +properties: + autorepeat: + description: Enable autorepeat when key is pressed and held down. + type: boolean + + linux,keycodes: + description: + Specifies an array of numeric keycode values to be used for reporting + button presses. + allOf: + - $ref: /schemas/types.yaml#/definitions/uint32-array + - items: + minimum: 0 + maximum: 0xff + + poll-interval: + description: Poll interval time in milliseconds. + $ref: /schemas/types.yaml#/definitions/uint32 + + power-off-time-sec: + description: + Duration in seconds which the key should be kept pressed for device to + power off automatically. Device with key pressed shutdown feature can + specify this property. + $ref: /schemas/types.yaml#/definitions/uint32 diff --git a/Documentation/devicetree/bindings/input/keys.txt b/Documentation/devicetree/bindings/input/keys.txt deleted file mode 100644 index f5a5ddde53f1..000000000000 --- a/Documentation/devicetree/bindings/input/keys.txt +++ /dev/null @@ -1,8 +0,0 @@ -General Keys Properties: - -Optional properties for Keys: -- power-off-time-sec: Duration in seconds which the key should be kept - pressed for device to power off automatically. Device with key pressed - shutdown feature can specify this property. -- linux,keycodes: Specifies the numeric keycode values to be used for - reporting key presses. diff --git a/Documentation/devicetree/bindings/input/mpr121-touchkey.txt b/Documentation/devicetree/bindings/input/mpr121-touchkey.txt deleted file mode 100644 index b7c61ee5841b..000000000000 --- a/Documentation/devicetree/bindings/input/mpr121-touchkey.txt +++ /dev/null @@ -1,30 +0,0 @@ -* Freescale MPR121 Controllor - -Required Properties: -- compatible: Should be "fsl,mpr121-touchkey" -- reg: The I2C slave address of the device. -- interrupts: The interrupt number to the cpu. -- vdd-supply: Phandle to the Vdd power supply. -- linux,keycodes: Specifies an array of numeric keycode values to - be used for reporting button presses. The array can - contain up to 12 entries. - -Optional Properties: -- wakeup-source: Use any event on keypad as wakeup event. -- autorepeat: Enable autorepeat feature. - -Example: - -#include "dt-bindings/input/input.h" - - touchkey: mpr121@5a { - compatible = "fsl,mpr121-touchkey"; - reg = <0x5a>; - interrupt-parent = <&gpio1>; - interrupts = <28 2>; - autorepeat; - vdd-supply = <&ldo4_reg>; - linux,keycodes = <KEY_0>, <KEY_1>, <KEY_2>, <KEY_3>, - <KEY_4> <KEY_5>, <KEY_6>, <KEY_7>, - <KEY_8>, <KEY_9>, <KEY_A>, <KEY_B>; - }; diff --git a/Documentation/devicetree/bindings/input/mtk-pmic-keys.txt b/Documentation/devicetree/bindings/input/mtk-pmic-keys.txt index 2888d07c2ef0..535d92885372 100644 --- a/Documentation/devicetree/bindings/input/mtk-pmic-keys.txt +++ b/Documentation/devicetree/bindings/input/mtk-pmic-keys.txt @@ -10,13 +10,13 @@ Documentation/devicetree/bindings/mfd/mt6397.txt Required properties: - compatible: "mediatek,mt6397-keys" or "mediatek,mt6323-keys" -- linux,keycodes: See Documentation/devicetree/bindings/input/keys.txt +- linux,keycodes: See Documentation/devicetree/bindings/input/input.yaml Optional Properties: - wakeup-source: See Documentation/devicetree/bindings/power/wakeup-source.txt - mediatek,long-press-mode: Long press key shutdown setting, 1 for pwrkey only, 2 for pwrkey/homekey together, others for disabled. -- power-off-time-sec: See Documentation/devicetree/bindings/input/keys.txt +- power-off-time-sec: See Documentation/devicetree/bindings/input/input.yaml Example: diff --git a/Documentation/devicetree/bindings/input/st,stpmic1-onkey.txt b/Documentation/devicetree/bindings/input/st,stpmic1-onkey.txt index 4494613ae7ad..eb8e83736c02 100644 --- a/Documentation/devicetree/bindings/input/st,stpmic1-onkey.txt +++ b/Documentation/devicetree/bindings/input/st,stpmic1-onkey.txt @@ -15,7 +15,7 @@ Optional properties: - st,onkey-pu-inactive: onkey pull up is not active - power-off-time-sec: Duration in seconds which the key should be kept pressed for device to power off automatically (from 1 to 16 seconds). - see See Documentation/devicetree/bindings/input/keys.txt + see See Documentation/devicetree/bindings/input/input.yaml Example: diff --git a/Documentation/devicetree/bindings/input/touchscreen/ad7879.txt b/Documentation/devicetree/bindings/input/touchscreen/ad7879.txt index cdd743a1f2d5..afa38dc069f0 100644 --- a/Documentation/devicetree/bindings/input/touchscreen/ad7879.txt +++ b/Documentation/devicetree/bindings/input/touchscreen/ad7879.txt @@ -38,7 +38,7 @@ Optional properties: Example: - ad7879@2c { + touchscreen0@2c { compatible = "adi,ad7879-1"; reg = <0x2c>; interrupt-parent = <&gpio1>; @@ -52,7 +52,7 @@ Example: adi,conversion-interval = /bits/ 8 <255>; }; - ad7879@1 { + touchscreen1@1 { compatible = "adi,ad7879"; spi-max-frequency = <5000000>; reg = <1>; diff --git a/Documentation/devicetree/bindings/input/touchscreen/edt-ft5x06.txt b/Documentation/devicetree/bindings/input/touchscreen/edt-ft5x06.txt index 870b8c5cce9b..0f6950073d6f 100644 --- a/Documentation/devicetree/bindings/input/touchscreen/edt-ft5x06.txt +++ b/Documentation/devicetree/bindings/input/touchscreen/edt-ft5x06.txt @@ -30,6 +30,7 @@ Required properties: Optional properties: - reset-gpios: GPIO specification for the RESET input - wake-gpios: GPIO specification for the WAKE input + - vcc-supply: Regulator that supplies the touchscreen - pinctrl-names: should be "default" - pinctrl-0: a phandle pointing to the pin settings for the diff --git a/Documentation/devicetree/bindings/leds/backlight/led-backlight.txt b/Documentation/devicetree/bindings/leds/backlight/led-backlight.txt new file mode 100644 index 000000000000..4c7dfbe7f67a --- /dev/null +++ b/Documentation/devicetree/bindings/leds/backlight/led-backlight.txt @@ -0,0 +1,28 @@ +led-backlight bindings + +This binding is used to describe a basic backlight device made of LEDs. +It can also be used to describe a backlight device controlled by the output of +a LED driver. + +Required properties: + - compatible: "led-backlight" + - leds: a list of LEDs + +Optional properties: + - brightness-levels: Array of distinct brightness levels. The levels must be + in the range accepted by the underlying LED devices. + This is used to translate a backlight brightness level + into a LED brightness level. If it is not provided, the + identity mapping is used. + + - default-brightness-level: The default brightness level. + +Example: + + backlight { + compatible = "led-backlight"; + + leds = <&led1>, <&led2>; + brightness-levels = <0 4 8 16 32 64 128 255>; + default-brightness-level = <6>; + }; diff --git a/Documentation/devicetree/bindings/leds/backlight/lm3630a-backlight.yaml b/Documentation/devicetree/bindings/leds/backlight/lm3630a-backlight.yaml index dc129d9a329e..08fe5cf8614a 100644 --- a/Documentation/devicetree/bindings/leds/backlight/lm3630a-backlight.yaml +++ b/Documentation/devicetree/bindings/leds/backlight/lm3630a-backlight.yaml @@ -29,6 +29,10 @@ properties: '#size-cells': const: 0 + enable-gpios: + description: GPIO to use to enable/disable the backlight (HWEN pin). + maxItems: 1 + required: - compatible - reg @@ -89,6 +93,7 @@ additionalProperties: false examples: - | + #include <dt-bindings/gpio/gpio.h> i2c { #address-cells = <1>; #size-cells = <0>; @@ -96,6 +101,7 @@ examples: led-controller@38 { compatible = "ti,lm3630a"; reg = <0x38>; + enable-gpios = <&gpio2 5 GPIO_ACTIVE_HIGH>; #address-cells = <1>; #size-cells = <0>; diff --git a/Documentation/devicetree/bindings/leds/backlight/pm8941-wled.txt b/Documentation/devicetree/bindings/leds/backlight/pm8941-wled.txt deleted file mode 100644 index e5b294dafc58..000000000000 --- a/Documentation/devicetree/bindings/leds/backlight/pm8941-wled.txt +++ /dev/null @@ -1,42 +0,0 @@ -Binding for Qualcomm PM8941 WLED driver - -Required properties: -- compatible: should be "qcom,pm8941-wled" -- reg: slave address - -Optional properties: -- default-brightness: brightness value on boot, value from: 0-4095 - default: 2048 -- label: The name of the backlight device -- qcom,cs-out: bool; enable current sink output -- qcom,cabc: bool; enable content adaptive backlight control -- qcom,ext-gen: bool; use externally generated modulator signal to dim -- qcom,current-limit: mA; per-string current limit; value from 0 to 25 - default: 20mA -- qcom,current-boost-limit: mA; boost current limit; one of: - 105, 385, 525, 805, 980, 1260, 1400, 1680 - default: 805mA -- qcom,switching-freq: kHz; switching frequency; one of: - 600, 640, 685, 738, 800, 872, 960, 1066, 1200, 1371, - 1600, 1920, 2400, 3200, 4800, 9600, - default: 1600kHz -- qcom,ovp: V; Over-voltage protection limit; one of: - 27, 29, 32, 35 - default: 29V -- qcom,num-strings: #; number of led strings attached; value from 1 to 3 - default: 2 - -Example: - -pm8941-wled@d800 { - compatible = "qcom,pm8941-wled"; - reg = <0xd800>; - label = "backlight"; - - qcom,cs-out; - qcom,current-limit = <20>; - qcom,current-boost-limit = <805>; - qcom,switching-freq = <1600>; - qcom,ovp = <29>; - qcom,num-strings = <2>; -}; diff --git a/Documentation/devicetree/bindings/leds/backlight/qcom-wled.txt b/Documentation/devicetree/bindings/leds/backlight/qcom-wled.txt new file mode 100644 index 000000000000..c06863badfbd --- /dev/null +++ b/Documentation/devicetree/bindings/leds/backlight/qcom-wled.txt @@ -0,0 +1,154 @@ +Binding for Qualcomm Technologies, Inc. WLED driver + +WLED (White Light Emitting Diode) driver is used for controlling display +backlight that is part of PMIC on Qualcomm Technologies, Inc. reference +platforms. The PMIC is connected to the host processor via SPMI bus. + +- compatible + Usage: required + Value type: <string> + Definition: should be one of: + "qcom,pm8941-wled" + "qcom,pmi8998-wled" + "qcom,pm660l-wled" + +- reg + Usage: required + Value type: <prop encoded array> + Definition: Base address of the WLED modules. + +- default-brightness + Usage: optional + Value type: <u32> + Definition: brightness value on boot, value from: 0-4095. + Default: 2048 + +- label + Usage: required + Value type: <string> + Definition: The name of the backlight device + +- qcom,cs-out + Usage: optional + Value type: <bool> + Definition: enable current sink output. + This property is supported only for PM8941. + +- qcom,cabc + Usage: optional + Value type: <bool> + Definition: enable content adaptive backlight control. + +- qcom,ext-gen + Usage: optional + Value type: <bool> + Definition: use externally generated modulator signal to dim. + This property is supported only for PM8941. + +- qcom,current-limit + Usage: optional + Value type: <u32> + Definition: mA; per-string current limit; value from 0 to 25 with + 1 mA step. Default 20 mA. + This property is supported only for pm8941. + +- qcom,current-limit-microamp + Usage: optional + Value type: <u32> + Definition: uA; per-string current limit; value from 0 to 30000 with + 2500 uA step. Default 25 mA. + +- qcom,current-boost-limit + Usage: optional + Value type: <u32> + Definition: mA; boost current limit. + For pm8941: one of: 105, 385, 525, 805, 980, 1260, 1400, + 1680. Default: 805 mA. + For pmi8998: one of: 105, 280, 450, 620, 970, 1150, 1300, + 1500. Default: 970 mA. + +- qcom,switching-freq + Usage: optional + Value type: <u32> + Definition: kHz; switching frequency; one of: 600, 640, 685, 738, + 800, 872, 960, 1066, 1200, 1371, 1600, 1920, 2400, 3200, + 4800, 9600. + Default: for pm8941: 1600 kHz + for pmi8998: 800 kHz + +- qcom,ovp + Usage: optional + Value type: <u32> + Definition: V; Over-voltage protection limit; one of: + 27, 29, 32, 35. Default: 29V + This property is supported only for PM8941. + +- qcom,ovp-millivolt + Usage: optional + Value type: <u32> + Definition: mV; Over-voltage protection limit; + For pmi8998: one of 18100, 19600, 29600, 31100. + Default 29600 mV. + If this property is not specified for PM8941, it + falls back to "qcom,ovp" property. + +- qcom,num-strings + Usage: optional + Value type: <u32> + Definition: #; number of led strings attached; + value: For PM8941 from 1 to 3. Default: 2 + For PMI8998 from 1 to 4. + +- interrupts + Usage: optional + Value type: <prop encoded array> + Definition: Interrupts associated with WLED. This should be + "short" and "ovp" interrupts. Interrupts can be + specified as per the encoding listed under + Documentation/devicetree/bindings/spmi/ + qcom,spmi-pmic-arb.txt. + +- interrupt-names + Usage: optional + Value type: <string> + Definition: Interrupt names associated with the interrupts. + Must be "short" and "ovp". The short circuit detection + is not supported for PM8941. + +- qcom,enabled-strings + Usage: optional + Value tyoe: <u32 array> + Definition: Array of the WLED strings numbered from 0 to 3. Each + string of leds are operated individually. Specify the + list of strings used by the device. Any combination of + led strings can be used. + +- qcom,external-pfet + Usage: optional + Value type: <bool> + Definition: Specify if external PFET control for short circuit + protection is used. This property is supported only + for PMI8998. + +- qcom,auto-string-detection + Usage: optional + Value type: <bool> + Definition: Enables auto-detection of the WLED string configuration. + This feature is not supported for PM8941. + + +Example: + +pm8941-wled@d800 { + compatible = "qcom,pm8941-wled"; + reg = <0xd800>; + label = "backlight"; + + qcom,cs-out; + qcom,current-limit = <20>; + qcom,current-boost-limit = <805>; + qcom,switching-freq = <1600>; + qcom,ovp = <29>; + qcom,num-strings = <2>; + qcom,enabled-strings = <0 1>; +}; diff --git a/Documentation/devicetree/bindings/leds/leds-el15203000.txt b/Documentation/devicetree/bindings/leds/leds-el15203000.txt new file mode 100644 index 000000000000..182f0035ed28 --- /dev/null +++ b/Documentation/devicetree/bindings/leds/leds-el15203000.txt @@ -0,0 +1,69 @@ +Crane Merchandising System - EL15203000 LED driver +-------------------------------------------------- + +This LED Board (aka RED LEDs board) is widely used in +coffee vending machines produced by Crane Merchandising Systems. +The board manages 3 LEDs and supports predefined blinking patterns +for specific leds. + +Vending area LED encoded with symbol 'V' (hex code 0x56). +Doesn't have any hardware blinking pattern. + +Screen light tube LED which surrounds vending machine screen and +encoded with symbol 'S' (hex code 0x53). Supports blinking breathing pattern. + +Water Pipe LED encoded with symbol 'P' (hex code 0x50) and +actually consists of 5 LEDs that exposed by protocol like one LED. +Supports next patterns: +- cascade pattern +- inversed cascade pattern +- bounce pattern +- inversed bounce pattern + +Required properties: +- compatible : "crane,el15203000" +- #address-cells : must be 1 +- #size-cells : must be 0 + +Property rules described in Documentation/devicetree/bindings/spi/spi-bus.txt +apply. In particular, "reg" and "spi-max-frequency" properties must be given. + +Optional LED sub-node properties: +- function: + see Documentation/devicetree/bindings/leds/common.txt +- color: + see Documentation/devicetree/bindings/leds/common.txt + +Example +------- + +#include <dt-bindings/leds/common.h> + +led-controller@0 { + compatible = "crane,el15203000"; + reg = <0>; + spi-max-frequency = <50000>; + #address-cells = <1>; + #size-cells = <0>; + + /* water pipe */ + led@50 { + reg = <0x50>; + function = "pipe"; + color = <LED_COLOR_ID_RED>; + }; + + /* screen frame */ + led@53 { + reg = <0x53>; + function = "screen"; + color = <LED_COLOR_ID_RED>; + }; + + /* vending area */ + led@56 { + reg = <0x56>; + function = "vend"; + color = <LED_COLOR_ID_RED>; + }; +}; diff --git a/Documentation/devicetree/bindings/mailbox/fsl,mu.txt b/Documentation/devicetree/bindings/mailbox/fsl,mu.txt index f3cf77eb5ab4..9c43357c5924 100644 --- a/Documentation/devicetree/bindings/mailbox/fsl,mu.txt +++ b/Documentation/devicetree/bindings/mailbox/fsl,mu.txt @@ -21,6 +21,8 @@ Required properties: imx6sx, imx7s, imx8qxp, imx8qm. The "fsl,imx6sx-mu" compatible is seen as generic and should be included together with SoC specific compatible. + There is a version 1.0 MU on imx7ulp, use "fsl,imx7ulp-mu" + compatible to support it. - reg : Should contain the registers location and length - interrupts : Interrupt number. The interrupt specifier format depends on the interrupt controller parent. diff --git a/Documentation/devicetree/bindings/mfd/madera.txt b/Documentation/devicetree/bindings/mfd/madera.txt index cad0f2800502..47e2b8bc6051 100644 --- a/Documentation/devicetree/bindings/mfd/madera.txt +++ b/Documentation/devicetree/bindings/mfd/madera.txt @@ -67,6 +67,14 @@ Optional properties: As defined in bindings/gpio.txt. Although optional, it is strongly recommended to use a hardware reset + - clocks: Should reference the clocks supplied on MCLK1, MCLK2 and MCLK3 + - clock-names: May contain up to three strings: + "mclk1" for the clock supplied on MCLK1, recommended to be a high + quality audio reference clock + "mclk2" for the clock supplied on MCLK2, required to be an always on + 32k clock + "mclk3" for the clock supplied on MCLK3 + - MICBIASx : Initial data for the MICBIAS regulators, as covered in Documentation/devicetree/bindings/regulator/regulator.txt. One for each MICBIAS generator (MICBIAS1, MICBIAS2, ...) diff --git a/Documentation/devicetree/bindings/mfd/max77650.txt b/Documentation/devicetree/bindings/mfd/max77650.txt deleted file mode 100644 index b529d8d19335..000000000000 --- a/Documentation/devicetree/bindings/mfd/max77650.txt +++ /dev/null @@ -1,46 +0,0 @@ -MAX77650 ultra low-power PMIC from Maxim Integrated. - -Required properties: -------------------- -- compatible: Must be "maxim,max77650" -- reg: I2C device address. -- interrupts: The interrupt on the parent the controller is - connected to. -- interrupt-controller: Marks the device node as an interrupt controller. -- #interrupt-cells: Must be <2>. - -- gpio-controller: Marks the device node as a gpio controller. -- #gpio-cells: Must be <2>. The first cell is the pin number and - the second cell is used to specify the gpio active - state. - -Optional properties: --------------------- -gpio-line-names: Single string containing the name of the GPIO line. - -The GPIO-controller module is represented as part of the top-level PMIC -node. The device exposes a single GPIO line. - -For device-tree bindings of other sub-modules (regulator, power supply, -LEDs and onkey) refer to the binding documents under the respective -sub-system directories. - -For more details on GPIO bindings, please refer to the generic GPIO DT -binding document <devicetree/bindings/gpio/gpio.txt>. - -Example: --------- - - pmic@48 { - compatible = "maxim,max77650"; - reg = <0x48>; - - interrupt-controller; - interrupt-parent = <&gpio2>; - #interrupt-cells = <2>; - interrupts = <3 IRQ_TYPE_LEVEL_LOW>; - - gpio-controller; - #gpio-cells = <2>; - gpio-line-names = "max77650-charger"; - }; diff --git a/Documentation/devicetree/bindings/mfd/max77650.yaml b/Documentation/devicetree/bindings/mfd/max77650.yaml new file mode 100644 index 000000000000..4a70f875a6eb --- /dev/null +++ b/Documentation/devicetree/bindings/mfd/max77650.yaml @@ -0,0 +1,149 @@ +# SPDX-License-Identifier: GPL-2.0 +%YAML 1.2 +--- +$id: http://devicetree.org/schemas/mfd/max77650.yaml# +$schema: http://devicetree.org/meta-schemas/core.yaml# + +title: MAX77650 ultra low-power PMIC from Maxim Integrated. + +maintainers: + - Bartosz Golaszewski <bgolaszewski@baylibre.com> + +description: | + MAX77650 is an ultra-low power PMIC providing battery charging and power + supply for low-power IoT and wearable applications. + + The GPIO-controller module is represented as part of the top-level PMIC + node. The device exposes a single GPIO line. + + For device-tree bindings of other sub-modules (regulator, power supply, + LEDs and onkey) refer to the binding documents under the respective + sub-system directories. + +properties: + compatible: + const: maxim,max77650 + + reg: + description: + I2C device address. + maxItems: 1 + + interrupts: + maxItems: 1 + + interrupt-controller: true + + "#interrupt-cells": + const: 2 + description: + The first cell is the IRQ number, the second cell is the trigger type. + + gpio-controller: true + + "#gpio-cells": + const: 2 + description: + The first cell is the pin number and the second cell is used to specify + the gpio active state. + + gpio-line-names: + maxItems: 1 + description: + Single string containing the name of the GPIO line. + + regulators: + $ref: ../regulator/max77650-regulator.yaml + + charger: + $ref: ../power/supply/max77650-charger.yaml + + leds: + $ref: ../leds/leds-max77650.yaml + + onkey: + $ref: ../input/max77650-onkey.yaml + +required: + - compatible + - reg + - interrupts + - interrupt-controller + - "#interrupt-cells" + - gpio-controller + - "#gpio-cells" + +examples: + - | + #include <dt-bindings/interrupt-controller/irq.h> + #include <dt-bindings/input/linux-event-codes.h> + i2c { + #address-cells = <1>; + #size-cells = <0>; + + pmic@48 { + compatible = "maxim,max77650"; + reg = <0x48>; + + interrupt-controller; + interrupt-parent = <&gpio2>; + #interrupt-cells = <2>; + interrupts = <3 IRQ_TYPE_LEVEL_LOW>; + + gpio-controller; + #gpio-cells = <2>; + gpio-line-names = "max77650-charger"; + + regulators { + compatible = "maxim,max77650-regulator"; + + max77650_ldo: regulator@0 { + regulator-compatible = "ldo"; + regulator-name = "max77650-ldo"; + regulator-min-microvolt = <1350000>; + regulator-max-microvolt = <2937500>; + }; + + max77650_sbb0: regulator@1 { + regulator-compatible = "sbb0"; + regulator-name = "max77650-sbb0"; + regulator-min-microvolt = <800000>; + regulator-max-microvolt = <1587500>; + }; + }; + + charger { + compatible = "maxim,max77650-charger"; + input-voltage-min-microvolt = <4200000>; + input-current-limit-microamp = <285000>; + }; + + leds { + compatible = "maxim,max77650-led"; + #address-cells = <1>; + #size-cells = <0>; + + led@0 { + reg = <0>; + label = "blue:usr0"; + }; + + led@1 { + reg = <1>; + label = "red:usr1"; + linux,default-trigger = "heartbeat"; + }; + + led@2 { + reg = <2>; + label = "green:usr2"; + }; + }; + + onkey { + compatible = "maxim,max77650-onkey"; + linux,code = <KEY_END>; + maxim,onkey-slide; + }; + }; + }; diff --git a/Documentation/devicetree/bindings/mfd/max77693.txt b/Documentation/devicetree/bindings/mfd/max77693.txt index a3c60a7a3be1..0ced96e16c16 100644 --- a/Documentation/devicetree/bindings/mfd/max77693.txt +++ b/Documentation/devicetree/bindings/mfd/max77693.txt @@ -175,6 +175,7 @@ Example: maxim,thermal-regulation-celsius = <75>; maxim,battery-overcurrent-microamp = <3000000>; maxim,charge-input-threshold-microvolt = <4300000>; + }; led { compatible = "maxim,max77693-led"; diff --git a/Documentation/devicetree/bindings/mfd/qcom,spmi-pmic.txt b/Documentation/devicetree/bindings/mfd/qcom,spmi-pmic.txt index 143706222a51..fffc8fde3302 100644 --- a/Documentation/devicetree/bindings/mfd/qcom,spmi-pmic.txt +++ b/Documentation/devicetree/bindings/mfd/qcom,spmi-pmic.txt @@ -29,6 +29,8 @@ Required properties: "qcom,pm8916", "qcom,pm8004", "qcom,pm8909", + "qcom,pm8950", + "qcom,pmi8950", "qcom,pm8998", "qcom,pmi8998", "qcom,pm8005", diff --git a/Documentation/devicetree/bindings/remoteproc/qcom,q6v5.txt b/Documentation/devicetree/bindings/remoteproc/qcom,q6v5.txt index 41ca5df5be5a..c416746f93cf 100644 --- a/Documentation/devicetree/bindings/remoteproc/qcom,q6v5.txt +++ b/Documentation/devicetree/bindings/remoteproc/qcom,q6v5.txt @@ -12,6 +12,7 @@ on the Qualcomm Hexagon core. "qcom,msm8916-mss-pil", "qcom,msm8974-mss-pil" "qcom,msm8996-mss-pil" + "qcom,msm8998-mss-pil" "qcom,sdm845-mss-pil" - reg: @@ -41,6 +42,7 @@ on the Qualcomm Hexagon core. qcom,msm8974-mss-pil: must be "wdog", "fatal", "ready", "handover", "stop-ack" qcom,msm8996-mss-pil: + qcom,msm8998-mss-pil: qcom,sdm845-mss-pil: must be "wdog", "fatal", "ready", "handover", "stop-ack", "shutdown-ack" @@ -70,6 +72,9 @@ on the Qualcomm Hexagon core. qcom,msm8996-mss-pil: must be "iface", "bus", "mem", "xo", "gpll0_mss", "snoc_axi", "mnoc_axi", "pnoc", "qdss" + qcom,msm8998-mss-pil: + must be "iface", "bus", "mem", "xo", "gpll0_mss", + "snoc_axi", "mnoc_axi", "qdss" qcom,sdm845-mss-pil: must be "iface", "bus", "mem", "xo", "gpll0_mss", "snoc_axi", "mnoc_axi", "prng" @@ -137,6 +142,7 @@ For the compatible string below the following supplies are required: qcom,msm8974-mss-pil: no power-domain names required qcom,msm8996-mss-pil: + qcom,msm8998-mss-pil: must be "cx", "mx" qcom,sdm845-mss-pil: must be "cx", "mx", "mss", "load_state" diff --git a/Documentation/devicetree/bindings/rtc/rtc-mt6397.txt b/Documentation/devicetree/bindings/rtc/rtc-mt6397.txt new file mode 100644 index 000000000000..55a0c8874c03 --- /dev/null +++ b/Documentation/devicetree/bindings/rtc/rtc-mt6397.txt @@ -0,0 +1,29 @@ +Device-Tree bindings for MediaTek PMIC based RTC + +MediaTek PMIC based RTC is an independent function of MediaTek PMIC that works +as a type of multi-function device (MFD). The RTC can be configured and set up +with PMIC wrapper bus which is a common resource shared with the other +functions found on the same PMIC. + +For MediaTek PMIC MFD bindings, see: +../mfd/mt6397.txt + +For MediaTek PMIC wrapper bus bindings, see: +../soc/mediatek/pwrap.txt + +Required properties: +- compatible: Should be one of follows + "mediatek,mt6323-rtc": for MT6323 PMIC + "mediatek,mt6397-rtc": for MT6397 PMIC + +Example: + + pmic { + compatible = "mediatek,mt6323"; + + ... + + rtc { + compatible = "mediatek,mt6323-rtc"; + }; + }; diff --git a/Documentation/devicetree/bindings/watchdog/atmel-sama5d4-wdt.txt b/Documentation/devicetree/bindings/watchdog/atmel-sama5d4-wdt.txt index 4fec1e3725b4..44727fcc2729 100644 --- a/Documentation/devicetree/bindings/watchdog/atmel-sama5d4-wdt.txt +++ b/Documentation/devicetree/bindings/watchdog/atmel-sama5d4-wdt.txt @@ -1,7 +1,7 @@ * Atmel SAMA5D4 Watchdog Timer (WDT) Controller Required properties: -- compatible: "atmel,sama5d4-wdt" +- compatible: "atmel,sama5d4-wdt" or "microchip,sam9x60-wdt" - reg: base physical address and length of memory mapped region. Optional properties: diff --git a/Documentation/driver-api/driver-model/devres.rst b/Documentation/driver-api/driver-model/devres.rst index 4ab193319d8c..13046fcf0a5d 100644 --- a/Documentation/driver-api/driver-model/devres.rst +++ b/Documentation/driver-api/driver-model/devres.rst @@ -314,6 +314,7 @@ IOMAP devm_ioport_unmap() devm_ioremap() devm_ioremap_nocache() + devm_ioremap_uc() devm_ioremap_wc() devm_ioremap_resource() : checks resource, requests memory region, ioremaps devm_ioremap_resource_wc() diff --git a/Documentation/driver-api/bt8xxgpio.rst b/Documentation/driver-api/gpio/bt8xxgpio.rst index a845feb074de..d7e75f1234e7 100644 --- a/Documentation/driver-api/bt8xxgpio.rst +++ b/Documentation/driver-api/gpio/bt8xxgpio.rst @@ -2,7 +2,7 @@ A driver for a selfmade cheap BT8xx based PCI GPIO-card (bt8xxgpio) =================================================================== -For advanced documentation, see http://www.bu3sch.de/btgpio.php +For advanced documentation, see https://bues.ch/cms/unmaintained/btgpio.html A generic digital 24-port PCI GPIO card can be built out of an ordinary Brooktree bt848, bt849, bt878 or bt879 based analog TV tuner card. The diff --git a/Documentation/driver-api/gpio/driver.rst b/Documentation/driver-api/gpio/driver.rst index 3fdb32422f8a..10ef357ef658 100644 --- a/Documentation/driver-api/gpio/driver.rst +++ b/Documentation/driver-api/gpio/driver.rst @@ -5,7 +5,7 @@ GPIO Driver Interface This document serves as a guide for writers of GPIO chip drivers. Each GPIO controller driver needs to include the following header, which defines -the structures used to define a GPIO driver: +the structures used to define a GPIO driver:: #include <linux/gpio/driver.h> @@ -398,12 +398,15 @@ provided. A big portion of overhead code will be managed by gpiolib, under the assumption that your interrupts are 1-to-1-mapped to the GPIO line index: - GPIO line offset Hardware IRQ - 0 0 - 1 1 - 2 2 - ... ... - ngpio-1 ngpio-1 +.. csv-table:: + :header: GPIO line offset, Hardware IRQ + + 0,0 + 1,1 + 2,2 + ...,... + ngpio-1, ngpio-1 + If some GPIO lines do not have corresponding IRQs, the bitmask valid_mask and the flag need_valid_mask in gpio_irq_chip can be used to mask off some @@ -413,7 +416,9 @@ The preferred way to set up the helpers is to fill in the struct gpio_irq_chip inside struct gpio_chip before adding the gpio_chip. If you do this, the additional irq_chip will be set up by gpiolib at the same time as setting up the rest of the GPIO functionality. The following -is a typical example of a cascaded interrupt handler using gpio_irq_chip: +is a typical example of a cascaded interrupt handler using gpio_irq_chip:: + +.. code-block:: c /* Typical state container with dynamic irqchip */ struct my_gpio { @@ -448,7 +453,9 @@ is a typical example of a cascaded interrupt handler using gpio_irq_chip: return devm_gpiochip_add_data(dev, &g->gc, g); The helper support using hierarchical interrupt controllers as well. -In this case the typical set-up will look like this: +In this case the typical set-up will look like this:: + +.. code-block:: c /* Typical state container with dynamic irqchip */ struct my_gpio { diff --git a/Documentation/driver-api/gpio/index.rst b/Documentation/driver-api/gpio/index.rst index c5b8467f9104..5b61032aa4ea 100644 --- a/Documentation/driver-api/gpio/index.rst +++ b/Documentation/driver-api/gpio/index.rst @@ -13,6 +13,7 @@ Contents: board drivers-on-gpio legacy + bt8xxgpio Core ==== diff --git a/Documentation/driver-api/index.rst b/Documentation/driver-api/index.rst index d0efa35052e3..3bcd9a13fbb3 100644 --- a/Documentation/driver-api/index.rst +++ b/Documentation/driver-api/index.rst @@ -70,7 +70,6 @@ available subsections can be seen below. fpga/index acpi/index backlight/lp855x-driver.rst - bt8xxgpio connector console dcdbas diff --git a/Documentation/i2c/busses/i2c-i801.rst b/Documentation/i2c/busses/i2c-i801.rst index 2a570c214880..b83da0e94184 100644 --- a/Documentation/i2c/busses/i2c-i801.rst +++ b/Documentation/i2c/busses/i2c-i801.rst @@ -42,6 +42,7 @@ Supported adapters: * Intel Comet Lake (PCH) * Intel Elkhart Lake (PCH) * Intel Tiger Lake (PCH) + * Intel Jasper Lake (SOC) Datasheets: Publicly available at the Intel website diff --git a/Documentation/i2c/instantiating-devices.rst b/Documentation/i2c/instantiating-devices.rst index 1238f1fa3382..875ebe9e78e3 100644 --- a/Documentation/i2c/instantiating-devices.rst +++ b/Documentation/i2c/instantiating-devices.rst @@ -123,7 +123,7 @@ present or not (for example for an optional feature which is not present on cheap variants of a board but you have no way to tell them apart), or it may have different addresses from one board to the next (manufacturer changing its design without notice). In this case, you can call -i2c_new_probed_device() instead of i2c_new_device(). +i2c_new_scanned_device() instead of i2c_new_device(). Example (from the nxp OHCI driver):: @@ -139,8 +139,8 @@ Example (from the nxp OHCI driver):: i2c_adap = i2c_get_adapter(2); memset(&i2c_info, 0, sizeof(struct i2c_board_info)); strscpy(i2c_info.type, "isp1301_nxp", sizeof(i2c_info.type)); - isp1301_i2c_client = i2c_new_probed_device(i2c_adap, &i2c_info, - normal_i2c, NULL); + isp1301_i2c_client = i2c_new_scanned_device(i2c_adap, &i2c_info, + normal_i2c, NULL); i2c_put_adapter(i2c_adap); (...) } @@ -153,14 +153,14 @@ simply gives up. The driver which instantiated the I2C device is responsible for destroying it on cleanup. This is done by calling i2c_unregister_device() on the pointer that was earlier returned by i2c_new_device() or -i2c_new_probed_device(). +i2c_new_scanned_device(). Method 3: Probe an I2C bus for certain devices ---------------------------------------------- Sometimes you do not have enough information about an I2C device, not even -to call i2c_new_probed_device(). The typical case is hardware monitoring +to call i2c_new_scanned_device(). The typical case is hardware monitoring chips on PC mainboards. There are several dozen models, which can live at 25 different addresses. Given the huge number of mainboards out there, it is next to impossible to build an exhaustive list of the hardware diff --git a/Documentation/i2c/writing-clients.rst b/Documentation/i2c/writing-clients.rst index dddf0a14ab7c..ced309b5e0cc 100644 --- a/Documentation/i2c/writing-clients.rst +++ b/Documentation/i2c/writing-clients.rst @@ -185,14 +185,14 @@ Sometimes you know that a device is connected to a given I2C bus, but you don't know the exact address it uses. This happens on TV adapters for example, where the same driver supports dozens of slightly different models, and I2C device addresses change from one model to the next. In -that case, you can use the i2c_new_probed_device() variant, which is +that case, you can use the i2c_new_scanned_device() variant, which is similar to i2c_new_device(), except that it takes an additional list of possible I2C addresses to probe. A device is created for the first responsive address in the list. If you expect more than one device to be -present in the address range, simply call i2c_new_probed_device() that +present in the address range, simply call i2c_new_scanned_device() that many times. -The call to i2c_new_device() or i2c_new_probed_device() typically happens +The call to i2c_new_device() or i2c_new_scanned_device() typically happens in the I2C bus driver. You may want to save the returned i2c_client reference for later use. @@ -237,7 +237,7 @@ Device Deletion --------------- Each I2C device which has been created using i2c_new_device() or -i2c_new_probed_device() can be unregistered by calling +i2c_new_scanned_device() can be unregistered by calling i2c_unregister_device(). If you don't call it explicitly, it will be called automatically before the underlying I2C bus itself is removed, as a device can't survive its parent in the device driver model. diff --git a/Documentation/networking/ppp_generic.txt b/Documentation/networking/ppp_generic.txt index 61daf4b39600..fd563aff5fc9 100644 --- a/Documentation/networking/ppp_generic.txt +++ b/Documentation/networking/ppp_generic.txt @@ -378,6 +378,8 @@ an interface unit are: CONFIG_PPP_FILTER option is enabled, the set of packets which reset the transmit and receive idle timers is restricted to those which pass the `active' packet filter. + Two versions of this command exist, to deal with user space + expecting times as either 32-bit or 64-bit time_t seconds. * PPPIOCSMAXCID sets the maximum connection-ID parameter (and thus the number of connection slots) for the TCP header compressor and diff --git a/Documentation/powerpc/index.rst b/Documentation/powerpc/index.rst index db7b6a880f52..ba5edb3211c0 100644 --- a/Documentation/powerpc/index.rst +++ b/Documentation/powerpc/index.rst @@ -19,6 +19,7 @@ powerpc firmware-assisted-dump hvcs isa-versions + kaslr-booke32 mpc52xx pci_iov_resource_on_powernv pmu-ebb diff --git a/Documentation/powerpc/kaslr-booke32.rst b/Documentation/powerpc/kaslr-booke32.rst new file mode 100644 index 000000000000..8b259fdfdf03 --- /dev/null +++ b/Documentation/powerpc/kaslr-booke32.rst @@ -0,0 +1,42 @@ +.. SPDX-License-Identifier: GPL-2.0 + +=========================== +KASLR for Freescale BookE32 +=========================== + +The word KASLR stands for Kernel Address Space Layout Randomization. + +This document tries to explain the implementation of the KASLR for +Freescale BookE32. KASLR is a security feature that deters exploit +attempts relying on knowledge of the location of kernel internals. + +Since CONFIG_RELOCATABLE has already supported, what we need to do is +map or copy kernel to a proper place and relocate. Freescale Book-E +parts expect lowmem to be mapped by fixed TLB entries(TLB1). The TLB1 +entries are not suitable to map the kernel directly in a randomized +region, so we chose to copy the kernel to a proper place and restart to +relocate. + +Entropy is derived from the banner and timer base, which will change every +build and boot. This not so much safe so additionally the bootloader may +pass entropy via the /chosen/kaslr-seed node in device tree. + +We will use the first 512M of the low memory to randomize the kernel +image. The memory will be split in 64M zones. We will use the lower 8 +bit of the entropy to decide the index of the 64M zone. Then we chose a +16K aligned offset inside the 64M zone to put the kernel in:: + + KERNELBASE + + |--> 64M <--| + | | + +---------------+ +----------------+---------------+ + | |....| |kernel| | | + +---------------+ +----------------+---------------+ + | | + |-----> offset <-----| + + kernstart_virt_addr + +To enable KASLR, set CONFIG_RANDOMIZE_BASE = y. If KASLR is enable and you +want to disable it at runtime, add "nokaslr" to the kernel cmdline. |