diff options
Diffstat (limited to 'Documentation/x86/x86_64/boot-options.rst')
| -rw-r--r-- | Documentation/x86/x86_64/boot-options.rst | 335 |
1 files changed, 335 insertions, 0 deletions
diff --git a/Documentation/x86/x86_64/boot-options.rst b/Documentation/x86/x86_64/boot-options.rst new file mode 100644 index 000000000000..2f69836b8445 --- /dev/null +++ b/Documentation/x86/x86_64/boot-options.rst @@ -0,0 +1,335 @@ +.. SPDX-License-Identifier: GPL-2.0 + +=========================== +AMD64 Specific Boot Options +=========================== + +There are many others (usually documented in driver documentation), but +only the AMD64 specific ones are listed here. + +Machine check +============= +Please see Documentation/x86/x86_64/machinecheck for sysfs runtime tunables. + + mce=off + Disable machine check + mce=no_cmci + Disable CMCI(Corrected Machine Check Interrupt) that + Intel processor supports. Usually this disablement is + not recommended, but it might be handy if your hardware + is misbehaving. + Note that you'll get more problems without CMCI than with + due to the shared banks, i.e. you might get duplicated + error logs. + mce=dont_log_ce + Don't make logs for corrected errors. All events reported + as corrected are silently cleared by OS. + This option will be useful if you have no interest in any + of corrected errors. + mce=ignore_ce + Disable features for corrected errors, e.g. polling timer + and CMCI. All events reported as corrected are not cleared + by OS and remained in its error banks. + Usually this disablement is not recommended, however if + there is an agent checking/clearing corrected errors + (e.g. BIOS or hardware monitoring applications), conflicting + with OS's error handling, and you cannot deactivate the agent, + then this option will be a help. + mce=no_lmce + Do not opt-in to Local MCE delivery. Use legacy method + to broadcast MCEs. + mce=bootlog + Enable logging of machine checks left over from booting. + Disabled by default on AMD Fam10h and older because some BIOS + leave bogus ones. + If your BIOS doesn't do that it's a good idea to enable though + to make sure you log even machine check events that result + in a reboot. On Intel systems it is enabled by default. + mce=nobootlog + Disable boot machine check logging. + mce=tolerancelevel[,monarchtimeout] (number,number) + tolerance levels: + 0: always panic on uncorrected errors, log corrected errors + 1: panic or SIGBUS on uncorrected errors, log corrected errors + 2: SIGBUS or log uncorrected errors, log corrected errors + 3: never panic or SIGBUS, log all errors (for testing only) + Default is 1 + Can be also set using sysfs which is preferable. + monarchtimeout: + Sets the time in us to wait for other CPUs on machine checks. 0 + to disable. + mce=bios_cmci_threshold + Don't overwrite the bios-set CMCI threshold. This boot option + prevents Linux from overwriting the CMCI threshold set by the + bios. Without this option, Linux always sets the CMCI + threshold to 1. Enabling this may make memory predictive failure + analysis less effective if the bios sets thresholds for memory + errors since we will not see details for all errors. + mce=recovery + Force-enable recoverable machine check code paths + + nomce (for compatibility with i386) + same as mce=off + + Everything else is in sysfs now. + +APICs +===== + + apic + Use IO-APIC. Default + + noapic + Don't use the IO-APIC. + + disableapic + Don't use the local APIC + + nolapic + Don't use the local APIC (alias for i386 compatibility) + + pirq=... + See Documentation/x86/i386/IO-APIC.txt + + noapictimer + Don't set up the APIC timer + + no_timer_check + Don't check the IO-APIC timer. This can work around + problems with incorrect timer initialization on some boards. + + apicpmtimer + Do APIC timer calibration using the pmtimer. Implies + apicmaintimer. Useful when your PIT timer is totally broken. + +Timing +====== + + notsc + Deprecated, use tsc=unstable instead. + + nohpet + Don't use the HPET timer. + +Idle loop +========= + + idle=poll + Don't do power saving in the idle loop using HLT, but poll for rescheduling + event. This will make the CPUs eat a lot more power, but may be useful + to get slightly better performance in multiprocessor benchmarks. It also + makes some profiling using performance counters more accurate. + Please note that on systems with MONITOR/MWAIT support (like Intel EM64T + CPUs) this option has no performance advantage over the normal idle loop. + It may also interact badly with hyperthreading. + +Rebooting +========= + + reboot=b[ios] | t[riple] | k[bd] | a[cpi] | e[fi] [, [w]arm | [c]old] + bios + Use the CPU reboot vector for warm reset + warm + Don't set the cold reboot flag + cold + Set the cold reboot flag + triple + Force a triple fault (init) + kbd + Use the keyboard controller. cold reset (default) + acpi + Use the ACPI RESET_REG in the FADT. If ACPI is not configured or + the ACPI reset does not work, the reboot path attempts the reset + using the keyboard controller. + efi + Use efi reset_system runtime service. If EFI is not configured or + the EFI reset does not work, the reboot path attempts the reset using + the keyboard controller. + + Using warm reset will be much faster especially on big memory + systems because the BIOS will not go through the memory check. + Disadvantage is that not all hardware will be completely reinitialized + on reboot so there may be boot problems on some systems. + + reboot=force + Don't stop other CPUs on reboot. This can make reboot more reliable + in some cases. + +Non Executable Mappings +======================= + + noexec=on|off + on + Enable(default) + off + Disable + +NUMA +==== + + numa=off + Only set up a single NUMA node spanning all memory. + + numa=noacpi + Don't parse the SRAT table for NUMA setup + + numa=fake=<size>[MG] + If given as a memory unit, fills all system RAM with nodes of + size interleaved over physical nodes. + + numa=fake=<N> + If given as an integer, fills all system RAM with N fake nodes + interleaved over physical nodes. + + numa=fake=<N>U + If given as an integer followed by 'U', it will divide each + physical node into N emulated nodes. + +ACPI +==== + + acpi=off + Don't enable ACPI + acpi=ht + Use ACPI boot table parsing, but don't enable ACPI interpreter + acpi=force + Force ACPI on (currently not needed) + acpi=strict + Disable out of spec ACPI workarounds. + acpi_sci={edge,level,high,low} + Set up ACPI SCI interrupt. + acpi=noirq + Don't route interrupts + acpi=nocmcff + Disable firmware first mode for corrected errors. This + disables parsing the HEST CMC error source to check if + firmware has set the FF flag. This may result in + duplicate corrected error reports. + +PCI +=== + + pci=off + Don't use PCI + pci=conf1 + Use conf1 access. + pci=conf2 + Use conf2 access. + pci=rom + Assign ROMs. + pci=assign-busses + Assign busses + pci=irqmask=MASK + Set PCI interrupt mask to MASK + pci=lastbus=NUMBER + Scan up to NUMBER busses, no matter what the mptable says. + pci=noacpi + Don't use ACPI to set up PCI interrupt routing. + +IOMMU (input/output memory management unit) +=========================================== +Multiple x86-64 PCI-DMA mapping implementations exist, for example: + + 1. <lib/dma-direct.c>: use no hardware/software IOMMU at all + (e.g. because you have < 3 GB memory). + Kernel boot message: "PCI-DMA: Disabling IOMMU" + + 2. <arch/x86/kernel/amd_gart_64.c>: AMD GART based hardware IOMMU. + Kernel boot message: "PCI-DMA: using GART IOMMU" + + 3. <arch/x86_64/kernel/pci-swiotlb.c> : Software IOMMU implementation. Used + e.g. if there is no hardware IOMMU in the system and it is need because + you have >3GB memory or told the kernel to us it (iommu=soft)) + Kernel boot message: "PCI-DMA: Using software bounce buffering + for IO (SWIOTLB)" + + 4. <arch/x86_64/pci-calgary.c> : IBM Calgary hardware IOMMU. Used in IBM + pSeries and xSeries servers. This hardware IOMMU supports DMA address + mapping with memory protection, etc. + Kernel boot message: "PCI-DMA: Using Calgary IOMMU" + +:: + + iommu=[<size>][,noagp][,off][,force][,noforce] + [,memaper[=<order>]][,merge][,fullflush][,nomerge] + [,noaperture][,calgary] + +General iommu options: + + off + Don't initialize and use any kind of IOMMU. + noforce + Don't force hardware IOMMU usage when it is not needed. (default). + force + Force the use of the hardware IOMMU even when it is + not actually needed (e.g. because < 3 GB memory). + soft + Use software bounce buffering (SWIOTLB) (default for + Intel machines). This can be used to prevent the usage + of an available hardware IOMMU. + +iommu options only relevant to the AMD GART hardware IOMMU: + + <size> + Set the size of the remapping area in bytes. + allowed + Overwrite iommu off workarounds for specific chipsets. + fullflush + Flush IOMMU on each allocation (default). + nofullflush + Don't use IOMMU fullflush. + memaper[=<order>] + Allocate an own aperture over RAM with size 32MB<<order. + (default: order=1, i.e. 64MB) + merge + Do scatter-gather (SG) merging. Implies "force" (experimental). + nomerge + Don't do scatter-gather (SG) merging. + noaperture + Ask the IOMMU not to touch the aperture for AGP. + noagp + Don't initialize the AGP driver and use full aperture. + panic + Always panic when IOMMU overflows. + calgary + Use the Calgary IOMMU if it is available + +iommu options only relevant to the software bounce buffering (SWIOTLB) IOMMU +implementation: + + swiotlb=<pages>[,force] + <pages> + Prereserve that many 128K pages for the software IO bounce buffering. + force + Force all IO through the software TLB. + +Settings for the IBM Calgary hardware IOMMU currently found in IBM +pSeries and xSeries machines + + calgary=[64k,128k,256k,512k,1M,2M,4M,8M] + Set the size of each PCI slot's translation table when using the + Calgary IOMMU. This is the size of the translation table itself + in main memory. The smallest table, 64k, covers an IO space of + 32MB; the largest, 8MB table, can cover an IO space of 4GB. + Normally the kernel will make the right choice by itself. + calgary=[translate_empty_slots] + Enable translation even on slots that have no devices attached to + them, in case a device will be hotplugged in the future. + calgary=[disable=<PCI bus number>] + Disable translation on a given PHB. For + example, the built-in graphics adapter resides on the first bridge + (PCI bus number 0); if translation (isolation) is enabled on this + bridge, X servers that access the hardware directly from user + space might stop working. Use this option if you have devices that + are accessed from userspace directly on some PCI host bridge. + panic + Always panic when IOMMU overflows + + +Miscellaneous +============= + + nogbpages + Do not use GB pages for kernel direct mappings. + gbpages + Use GB pages for kernel direct mappings. |