diff options
Diffstat (limited to 'Documentation/kernel-parameters.txt')
| -rw-r--r-- | Documentation/kernel-parameters.txt | 45 |
1 files changed, 43 insertions, 2 deletions
diff --git a/Documentation/kernel-parameters.txt b/Documentation/kernel-parameters.txt index 736d45602886..fbcddc5abe25 100644 --- a/Documentation/kernel-parameters.txt +++ b/Documentation/kernel-parameters.txt @@ -54,6 +54,7 @@ parameter is applicable: IMA Integrity measurement architecture is enabled. IOSCHED More than one I/O scheduler is enabled. IP_PNP IP DHCP, BOOTP, or RARP is enabled. + IPV6 IPv6 support is enabled. ISAPNP ISA PnP code is enabled. ISDN Appropriate ISDN support is enabled. JOY Appropriate joystick support is enabled. @@ -199,6 +200,10 @@ and is between 256 and 4096 characters. It is defined in the file acpi_display_output=video See above. + acpi_early_pdc_eval [HW,ACPI] Evaluate processor _PDC methods + early. Needed on some platforms to properly + initialize the EC. + acpi_irq_balance [HW,ACPI] ACPI will balance active IRQs default in APIC mode @@ -311,6 +316,11 @@ and is between 256 and 4096 characters. It is defined in the file aic79xx= [HW,SCSI] See Documentation/scsi/aic79xx.txt. + alignment= [KNL,ARM] + Allow the default userspace alignment fault handler + behaviour to be specified. Bit 0 enables warnings, + bit 1 enables fixups, and bit 2 sends a segfault. + amd_iommu= [HW,X86-84] Pass parameters to the AMD IOMMU driver in the system. Possible values are: @@ -347,6 +357,9 @@ and is between 256 and 4096 characters. It is defined in the file Change the amount of debugging information output when initialising the APIC and IO-APIC components. + autoconf= [IPV6] + See Documentation/networking/ipv6.txt. + show_lapic= [APIC,X86] Advanced Programmable Interrupt Controller Limit apic dumping. The parameter defines the maximal number of local apics being dumped. Also it is possible @@ -629,6 +642,12 @@ and is between 256 and 4096 characters. It is defined in the file See drivers/char/README.epca and Documentation/serial/digiepca.txt. + disable= [IPV6] + See Documentation/networking/ipv6.txt. + + disable_ipv6= [IPV6] + See Documentation/networking/ipv6.txt. + disable_mtrr_cleanup [X86] The kernel tries to adjust MTRR layout from continuous to discrete, to make X server driver able to add WB @@ -1729,6 +1748,9 @@ and is between 256 and 4096 characters. It is defined in the file nomfgpt [X86-32] Disable Multi-Function General Purpose Timer usage (for AMD Geode machines). + nopat [X86] Disable PAT (page attribute table extension of + pagetables) support. + norandmaps Don't use address space randomization. Equivalent to echo 0 > /proc/sys/kernel/randomize_va_space @@ -1939,8 +1961,12 @@ and is between 256 and 4096 characters. It is defined in the file IRQ routing is enabled. noacpi [X86] Do not use ACPI for IRQ routing or for PCI scanning. - use_crs [X86] Use _CRS for PCI resource - allocation. + use_crs [X86] Use PCI host bridge window information + from ACPI. On BIOSes from 2008 or later, this + is enabled by default. If you need to use this, + please report a bug. + nocrs [X86] Ignore PCI host bridge windows from ACPI. + If you need to use this, please report a bug. routeirq Do IRQ routing for all PCI devices. This is normally done in pci_enable_device(), so this option is a temporary workaround @@ -1989,6 +2015,14 @@ and is between 256 and 4096 characters. It is defined in the file force Enable ASPM even on devices that claim not to support it. WARNING: Forcing ASPM on may cause system lockups. + pcie_pme= [PCIE,PM] Native PCIe PME signaling options: + off Do not use native PCIe PME signaling. + force Use native PCIe PME signaling even if the BIOS refuses + to allow the kernel to control the relevant PCIe config + registers. + nomsi Do not use MSI for native PCIe PME signaling (this makes + all PCIe root ports use INTx for everything). + pcmv= [HW,PCMCIA] BadgePAD 4 pd. [PARIDE] @@ -2694,6 +2728,13 @@ and is between 256 and 4096 characters. It is defined in the file medium is write-protected). Example: quirks=0419:aaf5:rl,0421:0433:rc + userpte= + [X86] Flags controlling user PTE allocations. + + nohigh = do not allocate PTE pages in + HIGHMEM regardless of setting + of CONFIG_HIGHPTE. + vdso= [X86,SH] vdso=2: enable compat VDSO (default with COMPAT_VDSO) vdso=1: enable VDSO (default) |