diff options
Diffstat (limited to 'Documentation/kernel-parameters.txt')
| -rw-r--r-- | Documentation/kernel-parameters.txt | 42 |
1 files changed, 39 insertions, 3 deletions
diff --git a/Documentation/kernel-parameters.txt b/Documentation/kernel-parameters.txt index 74339c57b914..eacb2e0397ae 100644 --- a/Documentation/kernel-parameters.txt +++ b/Documentation/kernel-parameters.txt @@ -1264,7 +1264,7 @@ bytes respectively. Such letter suffixes can also be entirely omitted. i8042.noloop [HW] Disable the AUX Loopback command while probing for the AUX port i8042.nomux [HW] Don't check presence of an active multiplexing - controller. Default: true. + controller i8042.nopnp [HW] Don't use ACPIPnP / PnPBIOS to discover KBD/AUX controllers i8042.notimeout [HW] Ignore timeout condition signalled by controller @@ -1307,6 +1307,18 @@ bytes respectively. Such letter suffixes can also be entirely omitted. .cdrom .chs .ignore_cable are additional options See Documentation/ide/ide.txt. + ide-generic.probe-mask= [HW] (E)IDE subsystem + Format: <int> + Probe mask for legacy ISA IDE ports. Depending on + platform up to 6 ports are supported, enabled by + setting corresponding bits in the mask to 1. The + default value is 0x0, which has a special meaning. + On systems that have PCI, it triggers scanning the + PCI bus for the first and the second port, which + are then probed. On systems without PCI the value + of 0x0 enables probing the two first ports as if it + was 0x3. + ide-pci-generic.all-generic-ide [HW] (E)IDE subsystem Claim all unknown PCI IDE storage controllers. @@ -1434,6 +1446,9 @@ bytes respectively. Such letter suffixes can also be entirely omitted. disable Do not enable intel_pstate as the default scaling driver for the supported processors + no_hwp + Do not enable hardware P state control (HWP) + if available. intremap= [X86-64, Intel-IOMMU] on enable Interrupt Remapping (default) @@ -1587,6 +1602,8 @@ bytes respectively. Such letter suffixes can also be entirely omitted. kmemleak= [KNL] Boot-time kmemleak enable/disable Valid arguments: on, off Default: on + Built with CONFIG_DEBUG_KMEMLEAK_DEFAULT_OFF=y, + the default is off. kmemcheck= [X86] Boot-time kmemcheck enable/disable/one-shot mode Valid arguments: 0, 1, 2 @@ -2495,6 +2512,9 @@ bytes respectively. Such letter suffixes can also be entirely omitted. timeout < 0: reboot immediately Format: <timeout> + panic_on_warn panic() instead of WARN(). Useful to cause kdump + on a WARN(). + crash_kexec_post_notifiers Run kdump after running panic-notifiers and dumping kmsg. This only for the users who doubt kdump always @@ -2926,6 +2946,13 @@ bytes respectively. Such letter suffixes can also be entirely omitted. quiescent states. Units are jiffies, minimum value is one, and maximum value is HZ. + rcutree.kthread_prio= [KNL,BOOT] + Set the SCHED_FIFO priority of the RCU + per-CPU kthreads (rcuc/N). This value is also + used for the priority of the RCU boost threads + (rcub/N). Valid values are 1-99 and the default + is 1 (the least-favored priority). + rcutree.rcu_nocb_leader_stride= [KNL] Set the number of NOCB kthread groups, which defaults to the square root of the number of @@ -3075,6 +3102,15 @@ bytes respectively. Such letter suffixes can also be entirely omitted. messages. Disable with a value less than or equal to zero. + rcupdate.rcu_self_test= [KNL] + Run the RCU early boot self tests + + rcupdate.rcu_self_test_bh= [KNL] + Run the RCU bh early boot self tests + + rcupdate.rcu_self_test_sched= [KNL] + Run the RCU sched early boot self tests + rdinit= [KNL] Format: <full_path> Run specified binary instead of /init from the ramdisk, @@ -3487,7 +3523,7 @@ bytes respectively. Such letter suffixes can also be entirely omitted. are saved. trace_buf_size=nn[KMG] - [FTRACE] will set tracing buffer size. + [FTRACE] will set tracing buffer size on each cpu. trace_event=[event-list] [FTRACE] Set and start specified trace events in order @@ -3607,7 +3643,7 @@ bytes respectively. Such letter suffixes can also be entirely omitted. usb-storage.delay_use= [UMS] The delay in seconds before a new device is - scanned for Logical Units (default 5). + scanned for Logical Units (default 1). usb-storage.quirks= [UMS] A list of quirks entries to supplement or |