diff options
Diffstat (limited to 'Documentation/devicetree')
57 files changed, 2276 insertions, 13 deletions
diff --git a/Documentation/devicetree/bindings/arm/arm-boards b/Documentation/devicetree/bindings/arm/arm-boards index 91f26148af79..fc81a7d6b0f1 100644 --- a/Documentation/devicetree/bindings/arm/arm-boards +++ b/Documentation/devicetree/bindings/arm/arm-boards @@ -1,3 +1,15 @@ +ARM Integrator/AP (Application Platform) and Integrator/CP (Compact Platform) +----------------------------------------------------------------------------- +ARM's oldest Linux-supported platform with connectors for different core +tiles of ARMv4, ARMv5 and ARMv6 type. + +Required properties (in root node): + compatible = "arm,integrator-ap"; /* Application Platform */ + compatible = "arm,integrator-cp"; /* Compact Platform */ + +FPGA type interrupt controllers, see the versatile-fpga-irq binding doc. + + ARM Versatile Application and Platform Baseboards ------------------------------------------------- ARM's development hardware platform with connectors for customizable diff --git a/Documentation/devicetree/bindings/arm/davinci/nand.txt b/Documentation/devicetree/bindings/arm/davinci/nand.txt new file mode 100644 index 000000000000..e37241f1fdd8 --- /dev/null +++ b/Documentation/devicetree/bindings/arm/davinci/nand.txt @@ -0,0 +1,51 @@ +* Texas Instruments Davinci NAND + +This file provides information, what the device node for the +davinci nand interface contain. + +Required properties: +- compatible: "ti,davinci-nand"; +- reg : contain 2 offset/length values: + - offset and length for the access window + - offset and length for accessing the aemif control registers +- ti,davinci-chipselect: Indicates on the davinci_nand driver which + chipselect is used for accessing the nand. + +Recommended properties : +- ti,davinci-mask-ale: mask for ale +- ti,davinci-mask-cle: mask for cle +- ti,davinci-mask-chipsel: mask for chipselect +- ti,davinci-ecc-mode: ECC mode valid values for davinci driver: + - "none" + - "soft" + - "hw" +- ti,davinci-ecc-bits: used ECC bits, currently supported 1 or 4. +- ti,davinci-nand-buswidth: buswidth 8 or 16 +- ti,davinci-nand-use-bbt: use flash based bad block table support. + +Example (enbw_cmc board): +aemif@60000000 { + compatible = "ti,davinci-aemif"; + #address-cells = <2>; + #size-cells = <1>; + reg = <0x68000000 0x80000>; + ranges = <2 0 0x60000000 0x02000000 + 3 0 0x62000000 0x02000000 + 4 0 0x64000000 0x02000000 + 5 0 0x66000000 0x02000000 + 6 0 0x68000000 0x02000000>; + nand@3,0 { + compatible = "ti,davinci-nand"; + reg = <3 0x0 0x807ff + 6 0x0 0x8000>; + #address-cells = <1>; + #size-cells = <1>; + ti,davinci-chipselect = <1>; + ti,davinci-mask-ale = <0>; + ti,davinci-mask-cle = <0>; + ti,davinci-mask-chipsel = <0>; + ti,davinci-ecc-mode = "hw"; + ti,davinci-ecc-bits = <4>; + ti,davinci-nand-use-bbt; + }; +}; diff --git a/Documentation/devicetree/bindings/arm/versatile-fpga-irq.txt b/Documentation/devicetree/bindings/arm/versatile-fpga-irq.txt new file mode 100644 index 000000000000..9989eda755d9 --- /dev/null +++ b/Documentation/devicetree/bindings/arm/versatile-fpga-irq.txt @@ -0,0 +1,31 @@ +* ARM Versatile FPGA interrupt controller + +One or more FPGA IRQ controllers can be synthesized in an ARM reference board +such as the Integrator or Versatile family. The output of these different +controllers are OR:ed together and fed to the CPU tile's IRQ input. Each +instance can handle up to 32 interrupts. + +Required properties: +- compatible: "arm,versatile-fpga-irq" +- interrupt-controller: Identifies the node as an interrupt controller +- #interrupt-cells: The number of cells to define the interrupts. Must be 1 + as the FPGA IRQ controller has no configuration options for interrupt + sources. The cell is a u32 and defines the interrupt number. +- reg: The register bank for the FPGA interrupt controller. +- clear-mask: a u32 number representing the mask written to clear all IRQs + on the controller at boot for example. +- valid-mask: a u32 number representing a bit mask determining which of + the interrupts are valid. Unconnected/unused lines are set to 0, and + the system till not make it possible for devices to request these + interrupts. + +Example: + +pic: pic@14000000 { + compatible = "arm,versatile-fpga-irq"; + #interrupt-cells = <1>; + interrupt-controller; + reg = <0x14000000 0x100>; + clear-mask = <0xffffffff>; + valid-mask = <0x003fffff>; +}; diff --git a/Documentation/devicetree/bindings/arm/xen.txt b/Documentation/devicetree/bindings/arm/xen.txt new file mode 100644 index 000000000000..0f7b9c2109f8 --- /dev/null +++ b/Documentation/devicetree/bindings/arm/xen.txt @@ -0,0 +1,25 @@ +* Xen hypervisor device tree bindings + +Xen ARM virtual platforms shall have a top-level "hypervisor" node with +the following properties: + +- compatible: + compatible = "xen,xen-<version>", "xen,xen"; + where <version> is the version of the Xen ABI of the platform. + +- reg: specifies the base physical address and size of a region in + memory where the grant table should be mapped to, using an + HYPERVISOR_memory_op hypercall. The memory region is large enough to map + the whole grant table (it is larger or equal to gnttab_max_grant_frames()). + +- interrupts: the interrupt used by Xen to inject event notifications. + A GIC node is also required. + + +Example (assuming #address-cells = <2> and #size-cells = <2>): + +hypervisor { + compatible = "xen,xen-4.3", "xen,xen"; + reg = <0 0xb0000000 0 0x20000>; + interrupts = <1 15 0xf08>; +}; diff --git a/Documentation/devicetree/bindings/crypto/fsl-sec4.txt b/Documentation/devicetree/bindings/crypto/fsl-sec4.txt index bf57ecd5d73a..bd7ce120bc13 100644 --- a/Documentation/devicetree/bindings/crypto/fsl-sec4.txt +++ b/Documentation/devicetree/bindings/crypto/fsl-sec4.txt @@ -9,6 +9,7 @@ Copyright (C) 2008-2011 Freescale Semiconductor Inc. -Run Time Integrity Check (RTIC) Node -Run Time Integrity Check (RTIC) Memory Node -Secure Non-Volatile Storage (SNVS) Node + -Secure Non-Volatile Storage (SNVS) Low Power (LP) RTC Node -Full Example NOTE: the SEC 4 is also known as Freescale's Cryptographic Accelerator @@ -294,6 +295,27 @@ Secure Non-Volatile Storage (SNVS) Node address and length of the SEC4 configuration registers. + - #address-cells + Usage: required + Value type: <u32> + Definition: A standard property. Defines the number of cells + for representing physical addresses in child nodes. Must + have a value of 1. + + - #size-cells + Usage: required + Value type: <u32> + Definition: A standard property. Defines the number of cells + for representing the size of physical addresses in + child nodes. Must have a value of 1. + + - ranges + Usage: required + Value type: <prop-encoded-array> + Definition: A standard property. Specifies the physical address + range of the SNVS register space. A triplet that includes + the child address, parent address, & length. + - interrupts Usage: required Value type: <prop_encoded-array> @@ -314,11 +336,34 @@ EXAMPLE sec_mon@314000 { compatible = "fsl,sec-v4.0-mon"; reg = <0x314000 0x1000>; + ranges = <0 0x314000 0x1000>; interrupt-parent = <&mpic>; interrupts = <93 2>; }; ===================================================================== +Secure Non-Volatile Storage (SNVS) Low Power (LP) RTC Node + + A SNVS child node that defines SNVS LP RTC. + + - compatible + Usage: required + Value type: <string> + Definition: Must include "fsl,sec-v4.0-mon-rtc-lp". + + - reg + Usage: required + Value type: <prop-encoded-array> + Definition: A standard property. Specifies the physical + address and length of the SNVS LP configuration registers. + +EXAMPLE + sec_mon_rtc_lp@314000 { + compatible = "fsl,sec-v4.0-mon-rtc-lp"; + reg = <0x34 0x58>; + }; + +===================================================================== FULL EXAMPLE crypto: crypto@300000 { @@ -390,8 +435,14 @@ FULL EXAMPLE sec_mon: sec_mon@314000 { compatible = "fsl,sec-v4.0-mon"; reg = <0x314000 0x1000>; + ranges = <0 0x314000 0x1000>; interrupt-parent = <&mpic>; interrupts = <93 2>; + + sec_mon_rtc_lp@34 { + compatible = "fsl,sec-v4.0-mon-rtc-lp"; + reg = <0x34 0x58>; + }; }; ===================================================================== diff --git a/Documentation/devicetree/bindings/crypto/mv_cesa.txt b/Documentation/devicetree/bindings/crypto/mv_cesa.txt new file mode 100644 index 000000000000..47229b1a594b --- /dev/null +++ b/Documentation/devicetree/bindings/crypto/mv_cesa.txt @@ -0,0 +1,20 @@ +Marvell Cryptographic Engines And Security Accelerator + +Required properties: +- compatible : should be "marvell,orion-crypto" +- reg : base physical address of the engine and length of memory mapped + region, followed by base physical address of sram and its memory + length +- reg-names : "regs" , "sram"; +- interrupts : interrupt number + +Examples: + + crypto@30000 { + compatible = "marvell,orion-crypto"; + reg = <0x30000 0x10000>, + <0x4000000 0x800>; + reg-names = "regs" , "sram"; + interrupts = <22>; + status = "okay"; + }; diff --git a/Documentation/devicetree/bindings/gpio/gpio-fan.txt b/Documentation/devicetree/bindings/gpio/gpio-fan.txt new file mode 100644 index 000000000000..2dd457a3469a --- /dev/null +++ b/Documentation/devicetree/bindings/gpio/gpio-fan.txt @@ -0,0 +1,25 @@ +Bindings for fan connected to GPIO lines + +Required properties: +- compatible : "gpio-fan" +- gpios: Specifies the pins that map to bits in the control value, + ordered MSB-->LSB. +- gpio-fan,speed-map: A mapping of possible fan RPM speeds and the + control value that should be set to achieve them. This array + must have the RPM values in ascending order. + +Optional properties: +- alarm-gpios: This pin going active indicates something is wrong with + the fan, and a udev event will be fired. + +Examples: + + gpio_fan { + compatible = "gpio-fan"; + gpios = <&gpio1 14 1 + &gpio1 13 1>; + gpio-fan,speed-map = <0 0 + 3000 1 + 6000 2>; + alarm-gpios = <&gpio1 15 1>; + }; diff --git a/Documentation/devicetree/bindings/gpio/gpio-mvebu.txt b/Documentation/devicetree/bindings/gpio/gpio-mvebu.txt new file mode 100644 index 000000000000..a6f3bec1da7d --- /dev/null +++ b/Documentation/devicetree/bindings/gpio/gpio-mvebu.txt @@ -0,0 +1,53 @@ +* Marvell EBU GPIO controller + +Required properties: + +- compatible : Should be "marvell,orion-gpio", "marvell,mv78200-gpio" + or "marvell,armadaxp-gpio". "marvell,orion-gpio" should be used for + Orion, Kirkwood, Dove, Discovery (except MV78200) and Armada + 370. "marvell,mv78200-gpio" should be used for the Discovery + MV78200. "marvel,armadaxp-gpio" should be used for all Armada XP + SoCs (MV78230, MV78260, MV78460). + +- reg: Address and length of the register set for the device. Only one + entry is expected, except for the "marvell,armadaxp-gpio" variant + for which two entries are expected: one for the general registers, + one for the per-cpu registers. + +- interrupts: The list of interrupts that are used for all the pins + managed by this GPIO bank. There can be more than one interrupt + (example: 1 interrupt per 8 pins on Armada XP, which means 4 + interrupts per bank of 32 GPIOs). + +- interrupt-controller: identifies the node as an interrupt controller + +- #interrupt-cells: specifies the number of cells needed to encode an + interrupt source. Should be two. + The first cell is the GPIO number. + The second cell is used to specify flags: + bits[3:0] trigger type and level flags: + 1 = low-to-high edge triggered. + 2 = high-to-low edge triggered. + 4 = active high level-sensitive. + 8 = active low level-sensitive. + +- gpio-controller: marks the device node as a gpio controller + +- ngpios: number of GPIOs this controller has + +- #gpio-cells: Should be two. The first cell is the pin number. The + second cell is reserved for flags, unused at the moment. + +Example: + + gpio0: gpio@d0018100 { + compatible = "marvell,armadaxp-gpio"; + reg = <0xd0018100 0x40>, + <0xd0018800 0x30>; + ngpios = <32>; + gpio-controller; + #gpio-cells = <2>; + interrupt-controller; + #interrupt-cells = <2>; + interrupts = <16>, <17>, <18>, <19>; + }; diff --git a/Documentation/devicetree/bindings/i2c/atmel-i2c.txt b/Documentation/devicetree/bindings/i2c/atmel-i2c.txt new file mode 100644 index 000000000000..b689a0d9441c --- /dev/null +++ b/Documentation/devicetree/bindings/i2c/atmel-i2c.txt @@ -0,0 +1,30 @@ +I2C for Atmel platforms + +Required properties : +- compatible : Must be "atmel,at91rm9200-i2c", "atmel,at91sam9261-i2c", + "atmel,at91sam9260-i2c", "atmel,at91sam9g20-i2c", "atmel,at91sam9g10-i2c" + or "atmel,at91sam9x5-i2c" +- reg: physical base address of the controller and length of memory mapped + region. +- interrupts: interrupt number to the cpu. +- #address-cells = <1>; +- #size-cells = <0>; + +Optional properties: +- Child nodes conforming to i2c bus binding + +Examples : + +i2c0: i2c@fff84000 { + compatible = "atmel,at91sam9g20-i2c"; + reg = <0xfff84000 0x100>; + interrupts = <12 4 6>; + #address-cells = <1>; + #size-cells = <0>; + + 24c512@50 { + compatible = "24c512"; + reg = <0x50>; + pagesize = <128>; + } +} diff --git a/Documentation/devicetree/bindings/i2c/davinci.txt b/Documentation/devicetree/bindings/i2c/davinci.txt new file mode 100644 index 000000000000..2dc935b4113d --- /dev/null +++ b/Documentation/devicetree/bindings/i2c/davinci.txt @@ -0,0 +1,28 @@ +* Texas Instruments Davinci I2C + +This file provides information, what the device node for the +davinci i2c interface contain. + +Required properties: +- compatible: "ti,davinci-i2c"; +- reg : Offset and length of the register set for the device + +Recommended properties : +- interrupts : standard interrupt property. +- clock-frequency : desired I2C bus clock frequency in Hz. + +Example (enbw_cmc board): + i2c@1c22000 { + compatible = "ti,davinci-i2c"; + reg = <0x22000 0x1000>; + clock-frequency = <100000>; + interrupts = <15>; + interrupt-parent = <&intc>; + #address-cells = <1>; + #size-cells = <0>; + + dtt@48 { + compatible = "national,lm75"; + reg = <0x48>; + }; + }; diff --git a/Documentation/devicetree/bindings/i2c/i2c-mxs.txt b/Documentation/devicetree/bindings/i2c/i2c-mxs.txt index 30ac3a0557f7..7a3fe9e5f4cb 100644 --- a/Documentation/devicetree/bindings/i2c/i2c-mxs.txt +++ b/Documentation/devicetree/bindings/i2c/i2c-mxs.txt @@ -6,6 +6,7 @@ Required properties: - interrupts: Should contain ERROR and DMA interrupts - clock-frequency: Desired I2C bus clock frequency in Hz. Only 100000Hz and 400000Hz modes are supported. +- fsl,i2c-dma-channel: APBX DMA channel for the I2C Examples: @@ -16,4 +17,5 @@ i2c0: i2c@80058000 { reg = <0x80058000 2000>; interrupts = <111 68>; clock-frequency = <100000>; + fsl,i2c-dma-channel = <6>; }; diff --git a/Documentation/devicetree/bindings/i2c/nomadik.txt b/Documentation/devicetree/bindings/i2c/nomadik.txt new file mode 100644 index 000000000000..72065b0ff680 --- /dev/null +++ b/Documentation/devicetree/bindings/i2c/nomadik.txt @@ -0,0 +1,23 @@ +I2C for Nomadik based systems + +Required (non-standard) properties: + - Nil + +Recommended (non-standard) properties: + - clock-frequency : Maximum bus clock frequency for the device + +Optional (non-standard) properties: + - Nil + +Example : + +i2c@80004000 { + compatible = "stericsson,db8500-i2c", "st,nomadik-i2c"; + reg = <0x80004000 0x1000>; + interrupts = <0 21 0x4>; + #address-cells = <1>; + #size-cells = <0>; + v-i2c-supply = <&db8500_vape_reg>; + + clock-frequency = <400000>; +}; diff --git a/Documentation/devicetree/bindings/interrupt-controller/brcm,bcm2835-armctrl-ic.txt b/Documentation/devicetree/bindings/interrupt-controller/brcm,bcm2835-armctrl-ic.txt index 548892c08c59..7da578d72123 100644 --- a/Documentation/devicetree/bindings/interrupt-controller/brcm,bcm2835-armctrl-ic.txt +++ b/Documentation/devicetree/bindings/interrupt-controller/brcm,bcm2835-armctrl-ic.txt @@ -7,7 +7,7 @@ as "armctrl" in the SoC documentation, hence naming of this binding. Required properties: -- compatible : should be "brcm,bcm2835-armctrl-ic.txt" +- compatible : should be "brcm,bcm2835-armctrl-ic" - reg : Specifies base physical address and size of the registers. - interrupt-controller : Identifies the node as an interrupt controller - #interrupt-cells : Specifies the number of cells needed to encode an diff --git a/Documentation/devicetree/bindings/mfd/88pm860x.txt b/Documentation/devicetree/bindings/mfd/88pm860x.txt new file mode 100644 index 000000000000..63f3ee33759c --- /dev/null +++ b/Documentation/devicetree/bindings/mfd/88pm860x.txt @@ -0,0 +1,85 @@ +* Marvell 88PM860x Power Management IC + +Required parent device properties: +- compatible : "marvell,88pm860x" +- reg : the I2C slave address for the 88pm860x chip +- interrupts : IRQ line for the 88pm860x chip +- interrupt-controller: describes the 88pm860x as an interrupt controller (has its own domain) +- #interrupt-cells : should be 1. + - The cell is the 88pm860x local IRQ number + +Optional parent device properties: +- marvell,88pm860x-irq-read-clr: inicates whether interrupt status is cleared by read +- marvell,88pm860x-slave-addr: 88pm860x are two chips solution. <reg> stores the I2C address + of one chip, and this property stores the I2C address of + another chip. + +88pm860x consists of a large and varied group of sub-devices: + +Device Supply Names Description +------ ------------ ----------- +88pm860x-onkey : : On key +88pm860x-rtc : : RTC +88pm8607 : : Regulators +88pm860x-backlight : : Backlight +88pm860x-led : : Led +88pm860x-touch : : Touchscreen + +Example: + + pmic: 88pm860x@34 { + compatible = "marvell,88pm860x"; + reg = <0x34>; + interrupts = <4>; + interrupt-parent = <&intc>; + interrupt-controller; + #interrupt-cells = <1>; + + marvell,88pm860x-irq-read-clr; + marvell,88pm860x-slave-addr = <0x11>; + + regulators { + BUCK1 { + regulator-min-microvolt = <1000000>; + regulator-max-microvolt = <1500000>; + regulator-boot-on; + regulator-always-on; + }; + LDO1 { + regulator-min-microvolt = <1200000>; + regulator-max-microvolt = <2800000>; + regulator-boot-on; + regulator-always-on; + }; + }; + rtc { + marvell,88pm860x-vrtc = <1>; + }; + touch { + marvell,88pm860x-gpadc-prebias = <1>; + marvell,88pm860x-gpadc-slot-cycle = <1>; + marvell,88pm860x-tsi-prebias = <6>; + marvell,88pm860x-pen-prebias = <16>; + marvell,88pm860x-pen-prechg = <2>; + marvell,88pm860x-resistor-X = <300>; + }; + backlights { + backlight-0 { + marvell,88pm860x-iset = <4>; + marvell,88pm860x-pwm = <3>; + }; + backlight-2 { + }; + }; + leds { + led0-red { + marvell,88pm860x-iset = <12>; + }; + led0-green { + marvell,88pm860x-iset = <12>; + }; + led0-blue { + marvell,88pm860x-iset = <12>; + }; + }; + }; diff --git a/Documentation/devicetree/bindings/mfd/syscon.txt b/Documentation/devicetree/bindings/mfd/syscon.txt new file mode 100644 index 000000000000..fe8150bb3248 --- /dev/null +++ b/Documentation/devicetree/bindings/mfd/syscon.txt @@ -0,0 +1,20 @@ +* System Controller Registers R/W driver + +System controller node represents a register region containing a set +of miscellaneous registers. The registers are not cohesive enough to +represent as any specific type of device. The typical use-case is for +some other node's driver, or platform-specific code, to acquire a +reference to the syscon node (e.g. by phandle, node path, or search +using a specific compatible value), interrogate the node (or associated +OS driver) to determine the location of the registers, and access the +registers directly. + +Required properties: +- compatible: Should contain "syscon". +- reg: the register region can be accessed from syscon + +Examples: +gpr: iomuxc-gpr@020e0000 { + compatible = "fsl,imx6q-iomuxc-gpr", "syscon"; + reg = <0x020e0000 0x38>; +}; diff --git a/Documentation/devicetree/bindings/mfd/tps65910.txt b/Documentation/devicetree/bindings/mfd/tps65910.txt index db03599ae4dc..2e3304888ffc 100644 --- a/Documentation/devicetree/bindings/mfd/tps65910.txt +++ b/Documentation/devicetree/bindings/mfd/tps65910.txt @@ -59,6 +59,8 @@ Optional properties: in TPS6591X datasheet) - ti,en-gpio-sleep: enable sleep control for gpios There should be 9 entries here, one for each gpio. +- ti,system-power-controller: Telling whether or not this pmic is controlling + the system power. Regulator Optional properties: - ti,regulator-ext-sleep-control: enable external sleep @@ -79,6 +81,8 @@ Example: #interrupt-cells = <2>; interrupt-controller; + ti,system-power-controller; + ti,vmbch-threshold = 0; ti,vmbch2-threshold = 0; ti,en-ck32k-xtal; diff --git a/Documentation/devicetree/bindings/mfd/twl4030-audio.txt b/Documentation/devicetree/bindings/mfd/twl4030-audio.txt new file mode 100644 index 000000000000..414d2ae0adf6 --- /dev/null +++ b/Documentation/devicetree/bindings/mfd/twl4030-audio.txt @@ -0,0 +1,46 @@ +Texas Instruments TWL family (twl4030) audio module + +The audio module inside the TWL family consist of an audio codec and a vibra +driver. + +Required properties: +- compatible : must be "ti,twl4030-audio" + +Optional properties, nodes: + +Audio functionality: +- codec { }: Need to be present if the audio functionality is used. Within this + section the following options can be used: +- ti,digimic_delay: Delay need after enabling the digimic to reduce artifacts + from the start of the recorded sample (in ms) +-ti,ramp_delay_value: HS ramp delay configuration to reduce pop noise +-ti,hs_extmute: Use external mute for HS pop reduction +-ti,hs_extmute_gpio: Use external GPIO to control the external mute +-ti,offset_cncl_path: Offset cancellation path selection, refer to TRM for the + valid values. + +Vibra functionality +- ti,enable-vibra: Need to be set to <1> if the vibra functionality is used. if + missing or it is 0, the vibra functionality is disabled. + +Example: +&i2c1 { + clock-frequency = <2600000>; + + twl: twl@48 { + reg = <0x48>; + interrupts = <7>; /* SYS_NIRQ cascaded to intc */ + interrupt-parent = <&intc>; + + twl_audio: audio { + compatible = "ti,twl4030-audio"; + + ti,enable-vibra = <1>; + + codec { + ti,ramp_delay_value = <3>; + }; + + }; + }; +}; diff --git a/Documentation/devicetree/bindings/mfd/twl6040.txt b/Documentation/devicetree/bindings/mfd/twl6040.txt index c855240f3a0e..0f5dd709d752 100644 --- a/Documentation/devicetree/bindings/mfd/twl6040.txt +++ b/Documentation/devicetree/bindings/mfd/twl6040.txt @@ -1,7 +1,7 @@ Texas Instruments TWL6040 family -The TWL6040s are 8-channel high quality low-power audio codecs providing audio -and vibra functionality on OMAP4+ platforms. +The TWL6040s are 8-channel high quality low-power audio codecs providing audio, +vibra and GPO functionality on OMAP4+ platforms. They are connected ot the host processor via i2c for commands, McPDM for audio data and commands. @@ -10,6 +10,8 @@ Required properties: - reg: must be 0x4b for i2c address - interrupts: twl6040 has one interrupt line connecteded to the main SoC - interrupt-parent: The parent interrupt controller +- gpio-controller: +- #gpio-cells = <1>: twl6040 provides GPO lines. - twl6040,audpwron-gpio: Power on GPIO line for the twl6040 - vio-supply: Regulator for the twl6040 VIO supply @@ -37,7 +39,6 @@ Example: &i2c1 { twl6040: twl@4b { compatible = "ti,twl6040"; - reg = <0x4b>; interrupts = <0 119 4>; interrupt-parent = <&gic>; @@ -60,3 +61,5 @@ Example: }; }; }; + +/include/ "twl6040.dtsi" diff --git a/Documentation/devicetree/bindings/misc/ifm-csi.txt b/Documentation/devicetree/bindings/misc/ifm-csi.txt new file mode 100644 index 000000000000..5bdfffb0b9f7 --- /dev/null +++ b/Documentation/devicetree/bindings/misc/ifm-csi.txt @@ -0,0 +1,41 @@ +IFM camera sensor interface on mpc5200 LocalPlus bus + +Required properties: +- compatible: "ifm,o2d-csi" +- reg: specifies sensor chip select number and associated address range +- interrupts: external interrupt line number and interrupt sense mode + of the interrupt line signaling frame valid events +- gpios: three gpio-specifiers for "capture", "reset" and "master enable" + GPIOs (strictly in this order). +- ifm,csi-clk-handle: the phandle to a node in the DT describing the sensor + clock generator. This node is usually a general purpose timer controller. +- ifm,csi-addr-bus-width: address bus width (valid values are 16, 24, 25) +- ifm,csi-data-bus-width: data bus width (valid values are 8 and 16) +- ifm,csi-wait-cycles: sensor bus wait cycles + +Optional properties: +- ifm,csi-byte-swap: if this property is present, the byte swapping on + the bus will be enabled. + +Example: + + csi@3,0 { + compatible = "ifm,o2d-csi"; + reg = <3 0 0x00100000>; /* CS 3, 1 MiB range */ + interrupts = <1 1 2>; /* IRQ1, edge falling */ + + ifm,csi-clk-handle = <&timer7>; + gpios = <&gpio_simple 23 0 /* image_capture */ + &gpio_simple 26 0 /* image_reset */ + &gpio_simple 29 0>; /* image_master_en */ + + ifm,csi-addr-bus-width = <24>; + ifm,csi-data-bus-width = <8>; + ifm,csi-wait-cycles = <0>; + }; + +The base address of the used chip select is specified in the +ranges property of the parent localbus node, for example: + + ranges = <0 0 0xff000000 0x01000000 + 3 0 0xe3000000 0x00100000>; diff --git a/Documentation/devicetree/bindings/mmc/atmel-hsmci.txt b/Documentation/devicetree/bindings/mmc/atmel-hsmci.txt new file mode 100644 index 000000000000..0a85c70cd30a --- /dev/null +++ b/Documentation/devicetree/bindings/mmc/atmel-hsmci.txt @@ -0,0 +1,68 @@ +* Atmel High Speed MultiMedia Card Interface + +This controller on atmel products provides an interface for MMC, SD and SDIO +types of memory cards. + +This file documents differences between the core properties described +by mmc.txt and the properties used by the atmel-mci driver. + +1) MCI node + +Required properties: +- compatible: should be "atmel,hsmci" +- #address-cells: should be one. The cell is the slot id. +- #size-cells: should be zero. +- at least one slot node + +The node contains child nodes for each slot that the platform uses + +Example MCI node: + +mmc0: mmc@f0008000 { + compatible = "atmel,hsmci"; + reg = <0xf0008000 0x600>; + interrupts = <12 4>; + #address-cells = <1>; + #size-cells = <0>; + + [ child node definitions...] +}; + +2) slot nodes + +Required properties: +- reg: should contain the slot id. +- bus-width: number of data lines connected to the controller + +Optional properties: +- cd-gpios: specify GPIOs for card detection +- cd-inverted: invert the value of external card detect gpio line +- wp-gpios: specify GPIOs for write protection + +Example slot node: + +slot@0 { + reg = <0>; + bus-width = <4>; + cd-gpios = <&pioD 15 0> + cd-inverted; +}; + +Example full MCI node: +mmc0: mmc@f0008000 { + compatible = "atmel,hsmci"; + reg = <0xf0008000 0x600>; + interrupts = <12 4>; + #address-cells = <1>; + #size-cells = <0>; + slot@0 { + reg = <0>; + bus-width = <4>; + cd-gpios = <&pioD 15 0> + cd-inverted; + }; + slot@1 { + reg = <1>; + bus-width = <4>; + }; +}; diff --git a/Documentation/devicetree/bindings/mmc/exynos-dw-mshc.txt b/Documentation/devicetree/bindings/mmc/exynos-dw-mshc.txt new file mode 100644 index 000000000000..792768953330 --- /dev/null +++ b/Documentation/devicetree/bindings/mmc/exynos-dw-mshc.txt @@ -0,0 +1,87 @@ +* Samsung Exynos specific extensions to the Synopsis Designware Mobile + Storage Host Controller + +The Synopsis designware mobile storage host controller is used to interface +a SoC with storage medium such as eMMC or SD/MMC cards. This file documents +differences between the core Synopsis dw mshc controller properties described +by synposis-dw-mshc.txt and the properties used by the Samsung Exynos specific +extensions to the Synopsis Designware Mobile Storage Host Controller. + +Required Properties: + +* compatible: should be + - "samsung,exynos4210-dw-mshc": for controllers with Samsung Exynos4210 + specific extentions. + - "samsung,exynos4412-dw-mshc": for controllers with Samsung Exynos4412 + specific extentions. + - "samsung,exynos5250-dw-mshc": for controllers with Samsung Exynos5250 + specific extentions. + +* samsung,dw-mshc-ciu-div: Specifies the divider value for the card interface + unit (ciu) clock. This property is applicable only for Exynos5 SoC's and + ignored for Exynos4 SoC's. The valid range of divider value is 0 to 7. + +* samsung,dw-mshc-sdr-timing: Specifies the value of CIU clock phase shift value + in transmit mode and CIU clock phase shift value in receive mode for single + data rate mode operation. Refer notes below for the order of the cells and the + valid values. + +* samsung,dw-mshc-ddr-timing: Specifies the value of CUI clock phase shift value + in transmit mode and CIU clock phase shift value in receive mode for double + data rate mode operation. Refer notes below for the order of the cells and the + valid values. + + Notes for the sdr-timing and ddr-timing values: + + The order of the cells should be + - First Cell: CIU clock phase shift value for tx mode. + - Second Cell: CIU clock phase shift value for rx mode. + + Valid values for SDR and DDR CIU clock timing for Exynos5250: + - valid value for tx phase shift and rx phase shift is 0 to 7. + - when CIU clock divider value is set to 3, all possible 8 phase shift + values can be used. + - if CIU clock divider value is 0 (that is divide by 1), both tx and rx + phase shift clocks should be 0. + +Required properties for a slot: + +* gpios: specifies a list of gpios used for command, clock and data bus. The + first gpio is the command line and the second gpio is the clock line. The + rest of the gpios (depending on the bus-width property) are the data lines in + no particular order. The format of the gpio specifier depends on the gpio + controller. + +Example: + + The MSHC controller node can be split into two portions, SoC specific and + board specific portions as listed below. + + dwmmc0@12200000 { + compatible = "samsung,exynos5250-dw-mshc"; + reg = <0x12200000 0x1000>; + interrupts = <0 75 0>; + #address-cells = <1>; + #size-cells = <0>; + }; + + dwmmc0@12200000 { + num-slots = <1>; + supports-highspeed; + broken-cd; + fifo-depth = <0x80>; + card-detect-delay = <200>; + samsung,dw-mshc-ciu-div = <3>; + samsung,dw-mshc-sdr-timing = <2 3>; + samsung,dw-mshc-ddr-timing = <1 2>; + + slot@0 { + reg = <0>; + bus-width = <8>; + gpios = <&gpc0 0 2 0 3>, <&gpc0 1 2 0 3>, + <&gpc1 0 2 3 3>, <&gpc1 1 2 3 3>, + <&gpc1 2 2 3 3>, <&gpc1 3 2 3 3>, + <&gpc0 3 2 3 3>, <&gpc0 4 2 3 3>, + <&gpc0 5 2 3 3>, <&gpc0 6 2 3 3>; + }; + }; diff --git a/Documentation/devicetree/bindings/mmc/mmc.txt b/Documentation/devicetree/bindings/mmc/mmc.txt index 8a6811f4a02f..8e2e0ba2f486 100644 --- a/Documentation/devicetree/bindings/mmc/mmc.txt +++ b/Documentation/devicetree/bindings/mmc/mmc.txt @@ -9,12 +9,17 @@ Interpreted by the OF core: Required properties: - bus-width: Number of data lines, can be <1>, <4>, or <8> +Card detection: +If no property below is supplied, standard SDHCI card detect is used. +Only one of the properties in this section should be supplied: + - broken-cd: There is no card detection available; polling must be used. + - cd-gpios: Specify GPIOs for card detection, see gpio binding + - non-removable: non-removable slot (like eMMC); assume always present. + Optional properties: -- cd-gpios: Specify GPIOs for card detection, see gpio binding - wp-gpios: Specify GPIOs for write protection, see gpio binding - cd-inverted: when present, polarity on the cd gpio line is inverted - wp-inverted: when present, polarity on the wp gpio line is inverted -- non-removable: non-removable slot (like eMMC) - max-frequency: maximum operating clock frequency Example: diff --git a/Documentation/devicetree/bindings/mmc/pxa-mmc.txt b/Documentation/devicetree/bindings/mmc/pxa-mmc.txt new file mode 100644 index 000000000000..b7025de7dced --- /dev/null +++ b/Documentation/devicetree/bindings/mmc/pxa-mmc.txt @@ -0,0 +1,25 @@ +* PXA MMC drivers + +Driver bindings for the PXA MCI (MMC/SDIO) interfaces + +Required properties: +- compatible: Should be "marvell,pxa-mmc". +- vmmc-supply: A regulator for VMMC + +Optional properties: +- marvell,detect-delay-ms: sets the detection delay timeout in ms. +- marvell,gpio-power: GPIO spec for the card power enable pin + +This file documents differences between the core properties in mmc.txt +and the properties used by the pxa-mmc driver. + +Examples: + +mmc0: mmc@41100000 { + compatible = "marvell,pxa-mmc"; + reg = <0x41100000 0x1000>; + interrupts = <23>; + cd-gpios = <&gpio 23 0>; + wp-gpios = <&gpio 24 0>; +}; + diff --git a/Documentation/devicetree/bindings/mmc/samsung-sdhci.txt b/Documentation/devicetree/bindings/mmc/samsung-sdhci.txt new file mode 100644 index 000000000000..630a7d7f4718 --- /dev/null +++ b/Documentation/devicetree/bindings/mmc/samsung-sdhci.txt @@ -0,0 +1,53 @@ +* Samsung's SDHCI Controller device tree bindings + +Samsung's SDHCI controller is used as a connectivity interface with external +MMC, SD and eMMC storage mediums. This file documents differences between the +core mmc properties described by mmc.txt and the properties used by the +Samsung implmentation of the SDHCI controller. + +Note: The mmc core bindings documentation states that if none of the core +card-detect bindings are used, then the standard sdhci card detect mechanism +is used. The Samsung's SDHCI controller bindings extends this as listed below. + +[A] The property "samsung,cd-pinmux-gpio" can be used as stated in the + "Optional Board Specific Properties" section below. + +[B] If core card-detect bindings and "samsung,cd-pinmux-gpio" property + is not specified, it is assumed that there is no card detection + mechanism used. + +Required SoC Specific Properties: +- compatible: should be one of the following + - "samsung,s3c6410-sdhci": For controllers compatible with s3c6410 sdhci + controller. + - "samsung,exynos4210-sdhci": For controllers compatible with Exynos4 sdhci + controller. + +Required Board Specific Properties: +- gpios: Should specify the gpios used for clock, command and data lines. The + gpio specifier format depends on the gpio controller. + +Optional Board Specific Properties: +- samsung,cd-pinmux-gpio: Specifies the card detect line that is routed + through a pinmux to the card-detect pin of the card slot. This property + should be used only if none of the mmc core card-detect properties are + used. + +Example: + sdhci@12530000 { + compatible = "samsung,exynos4210-sdhci"; + reg = <0x12530000 0x100>; + interrupts = <0 75 0>; + bus-width = <4>; + cd-gpios = <&gpk2 2 2 3 3>; + gpios = <&gpk2 0 2 0 3>, /* clock line */ + <&gpk2 1 2 0 3>, /* command line */ + <&gpk2 3 2 3 3>, /* data line 0 */ + <&gpk2 4 2 3 3>, /* data line 1 */ + <&gpk2 5 2 3 3>, /* data line 2 */ + <&gpk2 6 2 3 3>; /* data line 3 */ + }; + + Note: This example shows both SoC specific and board specific properties + in a single device node. The properties can be actually be seperated + into SoC specific node and board specific node. diff --git a/Documentation/devicetree/bindings/mmc/sdhci-dove.txt b/Documentation/devicetree/bindings/mmc/sdhci-dove.txt new file mode 100644 index 000000000000..ae9aab9abcd7 --- /dev/null +++ b/Documentation/devicetree/bindings/mmc/sdhci-dove.txt @@ -0,0 +1,14 @@ +* Marvell sdhci-dove controller + +This file documents differences between the core properties in mmc.txt +and the properties used by the sdhci-pxav2 and sdhci-pxav3 drivers. + +- compatible: Should be "marvell,dove-sdhci". + +Example: + +sdio0: sdio@92000 { + compatible = "marvell,dove-sdhci"; + reg = <0x92000 0x100>; + interrupts = <35>; +}; diff --git a/Documentation/devicetree/bindings/mmc/sdhci-spear.txt b/Documentation/devicetree/bindings/mmc/sdhci-spear.txt new file mode 100644 index 000000000000..fd3643e7e467 --- /dev/null +++ b/Documentation/devicetree/bindings/mmc/sdhci-spear.txt @@ -0,0 +1,18 @@ +* SPEAr SDHCI Controller + +This file documents differences between the core properties in mmc.txt +and the properties used by the sdhci-spear driver. + +Required properties: +- compatible: "st,spear300-sdhci" + +Optional properties: +- cd-gpios: card detect gpio, with zero flags. + +Example: + + sdhci@fc000000 { + compatible = "st,spear300-sdhci"; + reg = <0xfc000000 0x1000>; + cd-gpios = <&gpio0 6 0>; + }; diff --git a/Documentation/devicetree/bindings/mmc/synposis-dw-mshc.txt b/Documentation/devicetree/bindings/mmc/synposis-dw-mshc.txt new file mode 100644 index 000000000000..06cd32d08052 --- /dev/null +++ b/Documentation/devicetree/bindings/mmc/synposis-dw-mshc.txt @@ -0,0 +1,79 @@ +* Synopsis Designware Mobile Storage Host Controller + +The Synopsis designware mobile storage host controller is used to interface +a SoC with storage medium such as eMMC or SD/MMC cards. This file documents +differences between the core mmc properties described by mmc.txt and the +properties used by the Synopsis Designware Mobile Storage Host Controller. + +Required Properties: + +* compatible: should be + - snps,dw-mshc: for controllers compliant with synopsis dw-mshc. +* #address-cells: should be 1. +* #size-cells: should be 0. + +# Slots: The slot specific information are contained within child-nodes with + each child-node representing a supported slot. There should be atleast one + child node representing a card slot. The name of the child node representing + the slot is recommended to be slot@n where n is the unique number of the slot + connnected to the controller. The following are optional properties which + can be included in the slot child node. + + * reg: specifies the physical slot number. The valid values of this + property is 0 to (num-slots -1), where num-slots is the value + specified by the num-slots property. + + * bus-width: as documented in mmc core bindings. + + * wp-gpios: specifies the write protect gpio line. The format of the + gpio specifier depends on the gpio controller. If the write-protect + line is not available, this property is optional. + +Optional properties: + +* num-slots: specifies the number of slots supported by the controller. + The number of physical slots actually used could be equal or less than the + value specified by num-slots. If this property is not specified, the value + of num-slot property is assumed to be 1. + +* fifo-depth: The maximum size of the tx/rx fifo's. If this property is not + specified, the default value of the fifo size is determined from the + controller registers. + +* card-detect-delay: Delay in milli-seconds before detecting card after card + insert event. The default value is 0. + +* supports-highspeed: Enables support for high speed cards (upto 50MHz) + +* broken-cd: as documented in mmc core bindings. + +Aliases: + +- All the MSHC controller nodes should be represented in the aliases node using + the following format 'mshc{n}' where n is a unique number for the alias. + +Example: + +The MSHC controller node can be split into two portions, SoC specific and +board specific portions as listed below. + + dwmmc0@12200000 { + compatible = "snps,dw-mshc"; + reg = <0x12200000 0x1000>; + interrupts = <0 75 0>; + #address-cells = <1>; + #size-cells = <0>; + }; + + dwmmc0@12200000 { + num-slots = <1>; + supports-highspeed; + broken-cd; + fifo-depth = <0x80>; + card-detect-delay = <200>; + + slot@0 { + reg = <0>; + bus-width = <8>; + }; + }; diff --git a/Documentation/devicetree/bindings/mtd/atmel-nand.txt b/Documentation/devicetree/bindings/mtd/atmel-nand.txt index a20069502f5a..d555421ea49f 100644 --- a/Documentation/devicetree/bindings/mtd/atmel-nand.txt +++ b/Documentation/devicetree/bindings/mtd/atmel-nand.txt @@ -3,7 +3,9 @@ Atmel NAND flash Required properties: - compatible : "atmel,at91rm9200-nand". - reg : should specify localbus address and size used for the chip, - and if availlable the ECC. + and hardware ECC controller if available. + If the hardware ECC is PMECC, it should contain address and size for + PMECC, PMECC Error Location controller and ROM which has lookup tables. - atmel,nand-addr-offset : offset for the address latch. - atmel,nand-cmd-offset : offset for the command latch. - #address-cells, #size-cells : Must be present if the device has sub-nodes @@ -16,6 +18,15 @@ Optional properties: - nand-ecc-mode : String, operation mode of the NAND ecc mode, soft by default. Supported values are: "none", "soft", "hw", "hw_syndrome", "hw_oob_first", "soft_bch". +- atmel,has-pmecc : boolean to enable Programmable Multibit ECC hardware. + Only supported by at91sam9x5 or later sam9 product. +- atmel,pmecc-cap : error correct capability for Programmable Multibit ECC + Controller. Supported values are: 2, 4, 8, 12, 24. +- atmel,pmecc-sector-size : sector size for ECC computation. Supported values + are: 512, 1024. +- atmel,pmecc-lookup-table-offset : includes two offsets of lookup table in ROM + for different sector size. First one is for sector size 512, the next is for + sector size 1024. - nand-bus-width : 8 or 16 bus width if not present 8 - nand-on-flash-bbt: boolean to enable on flash bbt option if not present false @@ -39,3 +50,30 @@ nand0: nand@40000000,0 { ... }; }; + +/* for PMECC supported chips */ +nand0: nand@40000000 { + compatible = "atmel,at91rm9200-nand"; + #address-cells = <1>; + #size-cells = <1>; + reg = < 0x40000000 0x10000000 /* bus addr & size */ + 0xffffe000 0x00000600 /* PMECC addr & size */ + 0xffffe600 0x00000200 /* PMECC ERRLOC addr & size */ + 0x00100000 0x00100000 /* ROM addr & size */ + >; + atmel,nand-addr-offset = <21>; /* ale */ + atmel,nand-cmd-offset = <22>; /* cle */ + nand-on-flash-bbt; + nand-ecc-mode = "hw"; + atmel,has-pmecc; /* enable PMECC */ + atmel,pmecc-cap = <2>; + atmel,pmecc-sector-size = <512>; + atmel,pmecc-lookup-table-offset = <0x8000 0x10000>; + gpios = <&pioD 5 0 /* rdy */ + &pioD 4 0 /* nce */ + 0 /* cd */ + >; + partition@0 { + ... + }; +}; diff --git a/Documentation/devicetree/bindings/mtd/gpmi-nand.txt b/Documentation/devicetree/bindings/mtd/gpmi-nand.txt index 1a5bbd346d22..3fb3f9015365 100644 --- a/Documentation/devicetree/bindings/mtd/gpmi-nand.txt +++ b/Documentation/devicetree/bindings/mtd/gpmi-nand.txt @@ -12,6 +12,10 @@ Required properties: - interrupt-names : The interrupt names "gpmi-dma", "bch"; - fsl,gpmi-dma-channel : Should contain the dma channel it uses. +Optional properties: + - nand-on-flash-bbt: boolean to enable on flash bbt option if not + present false + The device tree may optionally contain sub-nodes describing partitions of the address space. See partition.txt for more detail. diff --git a/Documentation/devicetree/bindings/mtd/lpc32xx-mlc.txt b/Documentation/devicetree/bindings/mtd/lpc32xx-mlc.txt new file mode 100644 index 000000000000..d0a37252eb22 --- /dev/null +++ b/Documentation/devicetree/bindings/mtd/lpc32xx-mlc.txt @@ -0,0 +1,50 @@ +NXP LPC32xx SoC NAND MLC controller + +Required properties: +- compatible: "nxp,lpc3220-mlc" +- reg: Address and size of the controller +- interrupts: The NAND interrupt specification +- gpios: GPIO specification for NAND write protect + +The following required properties are very controller specific. See the LPC32xx +User Manual 7.5.14 MLC NAND Timing Register (the values here are specified in +Hz, to make them independent of actual clock speed and to provide for good +accuracy:) +- nxp,tcea_delay: TCEA_DELAY +- nxp,busy_delay: BUSY_DELAY +- nxp,nand_ta: NAND_TA +- nxp,rd_high: RD_HIGH +- nxp,rd_low: RD_LOW +- nxp,wr_high: WR_HIGH +- nxp,wr_low: WR_LOW + +Optional subnodes: +- Partitions, see Documentation/devicetree/bindings/mtd/partition.txt + +Example: + + mlc: flash@200A8000 { + compatible = "nxp,lpc3220-mlc"; + reg = <0x200A8000 0x11000>; + interrupts = <11 0>; + #address-cells = <1>; + #size-cells = <1>; + + nxp,tcea-delay = <333333333>; + nxp,busy-delay = <10000000>; + nxp,nand-ta = <18181818>; + nxp,rd-high = <31250000>; + nxp,rd-low = <45454545>; + nxp,wr-high = <40000000>; + nxp,wr-low = <83333333>; + gpios = <&gpio 5 19 1>; /* GPO_P3 19, active low */ + + mtd0@00000000 { + label = "boot"; + reg = <0x00000000 0x00064000>; + read-only; + }; + + ... + + }; diff --git a/Documentation/devicetree/bindings/mtd/lpc32xx-slc.txt b/Documentation/devicetree/bindings/mtd/lpc32xx-slc.txt new file mode 100644 index 000000000000..d94edc0fc554 --- /dev/null +++ b/Documentation/devicetree/bindings/mtd/lpc32xx-slc.txt @@ -0,0 +1,52 @@ +NXP LPC32xx SoC NAND SLC controller + +Required properties: +- compatible: "nxp,lpc3220-slc" +- reg: Address and size of the controller +- nand-on-flash-bbt: Use bad block table on flash +- gpios: GPIO specification for NAND write protect + +The following required properties are very controller specific. See the LPC32xx +User Manual: +- nxp,wdr-clks: Delay before Ready signal is tested on write (W_RDY) +- nxp,rdr-clks: Delay before Ready signal is tested on read (R_RDY) +(The following values are specified in Hz, to make them independent of actual +clock speed:) +- nxp,wwidth: Write pulse width (W_WIDTH) +- nxp,whold: Write hold time (W_HOLD) +- nxp,wsetup: Write setup time (W_SETUP) +- nxp,rwidth: Read pulse width (R_WIDTH) +- nxp,rhold: Read hold time (R_HOLD) +- nxp,rsetup: Read setup time (R_SETUP) + +Optional subnodes: +- Partitions, see Documentation/devicetree/bindings/mtd/partition.txt + +Example: + + slc: flash@20020000 { + compatible = "nxp,lpc3220-slc"; + reg = <0x20020000 0x1000>; + #address-cells = <1>; + #size-cells = <1>; + + nxp,wdr-clks = <14>; + nxp,wwidth = <40000000>; + nxp,whold = <100000000>; + nxp,wsetup = <100000000>; + nxp,rdr-clks = <14>; + nxp,rwidth = <40000000>; + nxp,rhold = <66666666>; + nxp,rsetup = <100000000>; + nand-on-flash-bbt; + gpios = <&gpio 5 19 1>; /* GPO_P3 19, active low */ + + mtd0@00000000 { + label = "phy3250-boot"; + reg = <0x00000000 0x00064000>; + read-only; + }; + + ... + + }; diff --git a/Documentation/devicetree/bindings/mtd/mtd-physmap.txt b/Documentation/devicetree/bindings/mtd/mtd-physmap.txt index a63c2bd7de2b..94de19b8f16b 100644 --- a/Documentation/devicetree/bindings/mtd/mtd-physmap.txt +++ b/Documentation/devicetree/bindings/mtd/mtd-physmap.txt @@ -16,6 +16,13 @@ file systems on embedded devices. - #address-cells, #size-cells : Must be present if the device has sub-nodes representing partitions (see below). In this case both #address-cells and #size-cells must be equal to 1. + - no-unaligned-direct-access: boolean to disable the default direct + mapping of the flash. + On some platforms (e.g. MPC5200) a direct 1:1 mapping may cause + problems with JFFS2 usage, as the local bus (LPB) doesn't support + unaligned accesses as implemented in the JFFS2 code via memcpy(). + By defining "no-unaligned-direct-access", the flash will not be + exposed directly to the MTD users (e.g. JFFS2) any more. For JEDEC compatible devices, the following additional properties are defined: diff --git a/Documentation/devicetree/bindings/pinctrl/lantiq,falcon-pinumx.txt b/Documentation/devicetree/bindings/pinctrl/lantiq,falcon-pinumx.txt new file mode 100644 index 000000000000..daa768956069 --- /dev/null +++ b/Documentation/devicetree/bindings/pinctrl/lantiq,falcon-pinumx.txt @@ -0,0 +1,83 @@ +Lantiq FALCON pinmux controller + +Required properties: +- compatible: "lantiq,pinctrl-falcon" +- reg: Should contain the physical address and length of the gpio/pinmux + register range + +Please refer to pinctrl-bindings.txt in this directory for details of the +common pinctrl bindings used by client devices, including the meaning of the +phrase "pin configuration node". + +Lantiq's pin configuration nodes act as a container for an abitrary number of +subnodes. Each of these subnodes represents some desired configuration for a +pin, a group, or a list of pins or groups. This configuration can include the +mux function to select on those group(s), and two pin configuration parameters: +pull-up and open-drain + +The name of each subnode is not important as long as it is unique; all subnodes +should be enumerated and processed purely based on their content. + +Each subnode only affects those parameters that are explicitly listed. In +other words, a subnode that lists a mux function but no pin configuration +parameters implies no information about any pin configuration parameters. +Similarly, a pin subnode that describes a pullup parameter implies no +information about e.g. the mux function. + +We support 2 types of nodes. + +Definition of mux function groups: + +Required subnode-properties: +- lantiq,groups : An array of strings. Each string contains the name of a group. + Valid values for these names are listed below. +- lantiq,function: A string containing the name of the function to mux to the + group. Valid values for function names are listed below. + +Valid values for group and function names: + + mux groups: + por, ntr, ntr8k, hrst, mdio, bootled, asc0, spi, spi cs0, spi cs1, i2c, + jtag, slic, pcm, asc1 + + functions: + rst, ntr, mdio, led, asc, spi, i2c, jtag, slic, pcm + + +Definition of pin configurations: + +Required subnode-properties: +- lantiq,pins : An array of strings. Each string contains the name of a pin. + Valid values for these names are listed below. + +Optional subnode-properties: +- lantiq,pull: Integer, representing the pull-down/up to apply to the pin. + 0: none, 1: down +- lantiq,drive-current: Boolean, enables drive-current +- lantiq,slew-rate: Boolean, enables slew-rate + +Example: + pinmux0 { + compatible = "lantiq,pinctrl-falcon"; + pinctrl-names = "default"; + pinctrl-0 = <&state_default>; + + state_default: pinmux { + asc0 { + lantiq,groups = "asc0"; + lantiq,function = "asc"; + }; + ntr { + lantiq,groups = "ntr8k"; + lantiq,function = "ntr"; + }; + i2c { + lantiq,groups = "i2c"; + lantiq,function = "i2c"; + }; + hrst { + lantiq,groups = "hrst"; + lantiq,function = "rst"; + }; + }; + }; diff --git a/Documentation/devicetree/bindings/pinctrl/lantiq,xway-pinumx.txt b/Documentation/devicetree/bindings/pinctrl/lantiq,xway-pinumx.txt new file mode 100644 index 000000000000..b5469db1d7ad --- /dev/null +++ b/Documentation/devicetree/bindings/pinctrl/lantiq,xway-pinumx.txt @@ -0,0 +1,97 @@ +Lantiq XWAY pinmux controller + +Required properties: +- compatible: "lantiq,pinctrl-xway" or "lantiq,pinctrl-xr9" +- reg: Should contain the physical address and length of the gpio/pinmux + register range + +Please refer to pinctrl-bindings.txt in this directory for details of the +common pinctrl bindings used by client devices, including the meaning of the +phrase "pin configuration node". + +Lantiq's pin configuration nodes act as a container for an abitrary number of +subnodes. Each of these subnodes represents some desired configuration for a +pin, a group, or a list of pins or groups. This configuration can include the +mux function to select on those group(s), and two pin configuration parameters: +pull-up and open-drain + +The name of each subnode is not important as long as it is unique; all subnodes +should be enumerated and processed purely based on their content. + +Each subnode only affects those parameters that are explicitly listed. In +other words, a subnode that lists a mux function but no pin configuration +parameters implies no information about any pin configuration parameters. +Similarly, a pin subnode that describes a pullup parameter implies no +information about e.g. the mux function. + +We support 2 types of nodes. + +Definition of mux function groups: + +Required subnode-properties: +- lantiq,groups : An array of strings. Each string contains the name of a group. + Valid values for these names are listed below. +- lantiq,function: A string containing the name of the function to mux to the + group. Valid values for function names are listed below. + +Valid values for group and function names: + + mux groups: + exin0, exin1, exin2, jtag, ebu a23, ebu a24, ebu a25, ebu clk, ebu cs1, + ebu wait, nand ale, nand cs1, nand cle, spi, spi_cs1, spi_cs2, spi_cs3, + spi_cs4, spi_cs5, spi_cs6, asc0, asc0 cts rts, stp, nmi , gpt1, gpt2, + gpt3, clkout0, clkout1, clkout2, clkout3, gnt1, gnt2, gnt3, req1, req2, + req3 + + additional mux groups (XR9 only): + mdio, nand rdy, nand rd, exin3, exin4, gnt4, req4 + + functions: + spi, asc, cgu, jtag, exin, stp, gpt, nmi, pci, ebu, mdio + + + +Definition of pin configurations: + +Required subnode-properties: +- lantiq,pins : An array of strings. Each string contains the name of a pin. + Valid values for these names are listed below. + +Optional subnode-properties: +- lantiq,pull: Integer, representing the pull-down/up to apply to the pin. + 0: none, 1: down, 2: up. +- lantiq,open-drain: Boolean, enables open-drain on the defined pin. + +Valid values for XWAY pin names: + Pinconf pins can be referenced via the names io0-io31. + +Valid values for XR9 pin names: + Pinconf pins can be referenced via the names io0-io55. + +Example: + gpio: pinmux@E100B10 { + compatible = "lantiq,pinctrl-xway"; + pinctrl-names = "default"; + pinctrl-0 = <&state_default>; + + #gpio-cells = <2>; + gpio-controller; + reg = <0xE100B10 0xA0>; + + state_default: pinmux { + stp { + lantiq,groups = "stp"; + lantiq,function = "stp"; + }; + pci { + lantiq,groups = "gnt1"; + lantiq,function = "pci"; + }; + conf_out { + lantiq,pins = "io4", "io5", "io6"; /* stp */ + lantiq,open-drain; + lantiq,pull = <0>; + }; + }; + }; + diff --git a/Documentation/devicetree/bindings/pinctrl/marvell,armada-370-pinctrl.txt b/Documentation/devicetree/bindings/pinctrl/marvell,armada-370-pinctrl.txt new file mode 100644 index 000000000000..01ef408e205f --- /dev/null +++ b/Documentation/devicetree/bindings/pinctrl/marvell,armada-370-pinctrl.txt @@ -0,0 +1,95 @@ +* Marvell Armada 370 SoC pinctrl driver for mpp + +Please refer to marvell,mvebu-pinctrl.txt in this directory for common binding +part and usage. + +Required properties: +- compatible: "marvell,88f6710-pinctrl" + +Available mpp pins/groups and functions: +Note: brackets (x) are not part of the mpp name for marvell,function and given +only for more detailed description in this document. + +name pins functions +================================================================================ +mpp0 0 gpio, uart0(rxd) +mpp1 1 gpo, uart0(txd) +mpp2 2 gpio, i2c0(sck), uart0(txd) +mpp3 3 gpio, i2c0(sda), uart0(rxd) +mpp4 4 gpio, cpu_pd(vdd) +mpp5 5 gpo, ge0(txclko), uart1(txd), spi1(clk), audio(mclk) +mpp6 6 gpio, ge0(txd0), sata0(prsnt), tdm(rst), audio(sdo) +mpp7 7 gpo, ge0(txd1), tdm(tdx), audio(lrclk) +mpp8 8 gpio, ge0(txd2), uart0(rts), tdm(drx), audio(bclk) +mpp9 9 gpo, ge0(txd3), uart1(txd), sd0(clk), audio(spdifo) +mpp10 10 gpio, ge0(txctl), uart0(cts), tdm(fsync), audio(sdi) +mpp11 11 gpio, ge0(rxd0), uart1(rxd), sd0(cmd), spi0(cs1), + sata1(prsnt), spi1(cs1) +mpp12 12 gpio, ge0(rxd1), i2c1(sda), sd0(d0), spi1(cs0), + audio(spdifi) +mpp13 13 gpio, ge0(rxd2), i2c1(sck), sd0(d1), tdm(pclk), + audio(rmclk) +mpp14 14 gpio, ge0(rxd3), pcie(clkreq0), sd0(d2), spi1(mosi), + spi0(cs2) +mpp15 15 gpio, ge0(rxctl), pcie(clkreq1), sd0(d3), spi1(miso), + spi0(cs3) +mpp16 16 gpio, ge0(rxclk), uart1(rxd), tdm(int), audio(extclk) +mpp17 17 gpo, ge(mdc) +mpp18 18 gpio, ge(mdio) +mpp19 19 gpio, ge0(txclk), ge1(txclkout), tdm(pclk) +mpp20 20 gpo, ge0(txd4), ge1(txd0) +mpp21 21 gpo, ge0(txd5), ge1(txd1), uart1(txd) +mpp22 22 gpo, ge0(txd6), ge1(txd2), uart0(rts) +mpp23 23 gpo, ge0(txd7), ge1(txd3), spi1(mosi) +mpp24 24 gpio, ge0(col), ge1(txctl), spi1(cs0) +mpp25 25 gpio, ge0(rxerr), ge1(rxd0), uart1(rxd) +mpp26 26 gpio, ge0(crs), ge1(rxd1), spi1(miso) +mpp27 27 gpio, ge0(rxd4), ge1(rxd2), uart0(cts) +mpp28 28 gpio, ge0(rxd5), ge1(rxd3) +mpp29 29 gpio, ge0(rxd6), ge1(rxctl), i2c1(sda) +mpp30 30 gpio, ge0(rxd7), ge1(rxclk), i2c1(sck) +mpp31 31 gpio, tclk, ge0(txerr) +mpp32 32 gpio, spi0(cs0) +mpp33 33 gpio, dev(bootcs), spi0(cs0) +mpp34 34 gpo, dev(wen0), spi0(mosi) +mpp35 35 gpo, dev(oen), spi0(sck) +mpp36 36 gpo, dev(a1), spi0(miso) +mpp37 37 gpo, dev(a0), sata0(prsnt) +mpp38 38 gpio, dev(ready), uart1(cts), uart0(cts) +mpp39 39 gpo, dev(ad0), audio(spdifo) +mpp40 40 gpio, dev(ad1), uart1(rts), uart0(rts) +mpp41 41 gpio, dev(ad2), uart1(rxd) +mpp42 42 gpo, dev(ad3), uart1(txd) +mpp43 43 gpo, dev(ad4), audio(bclk) +mpp44 44 gpo, dev(ad5), audio(mclk) +mpp45 45 gpo, dev(ad6), audio(lrclk) +mpp46 46 gpo, dev(ad7), audio(sdo) +mpp47 47 gpo, dev(ad8), sd0(clk), audio(spdifo) +mpp48 48 gpio, dev(ad9), uart0(rts), sd0(cmd), sata1(prsnt), + spi0(cs1) +mpp49 49 gpio, dev(ad10), pcie(clkreq1), sd0(d0), spi1(cs0), + audio(spdifi) +mpp50 50 gpio, dev(ad11), uart0(cts), sd0(d1), spi1(miso), + audio(rmclk) +mpp51 51 gpio, dev(ad12), i2c1(sda), sd0(d2), spi1(mosi) +mpp52 52 gpio, dev(ad13), i2c1(sck), sd0(d3), spi1(sck) +mpp53 53 gpio, dev(ad14), sd0(clk), tdm(pclk), spi0(cs2), + pcie(clkreq1) +mpp54 54 gpo, dev(ad15), tdm(dtx) +mpp55 55 gpio, dev(cs1), uart1(txd), tdm(rst), sata1(prsnt), + sata0(prsnt) +mpp56 56 gpio, dev(cs2), uart1(cts), uart0(cts), spi0(cs3), + pcie(clkreq0), spi1(cs1) +mpp57 57 gpio, dev(cs3), uart1(rxd), tdm(fsync), sata0(prsnt), + audio(sdo) +mpp58 58 gpio, dev(cs0), uart1(rts), tdm(int), audio(extclk), + uart0(rts) +mpp59 59 gpo, dev(ale0), uart1(rts), uart0(rts), audio(bclk) +mpp60 60 gpio, dev(ale1), uart1(rxd), sata0(prsnt), pcie(rst-out), + audio(sdi) +mpp61 61 gpo, dev(wen1), uart1(txd), audio(rclk) +mpp62 62 gpio, dev(a2), uart1(cts), tdm(drx), pcie(clkreq0), + audio(mclk), uart0(cts) +mpp63 63 gpo, spi0(sck), tclk +mpp64 64 gpio, spi0(miso), spi0-1(cs1) +mpp65 65 gpio, spi0(mosi), spi0-1(cs2) diff --git a/Documentation/devicetree/bindings/pinctrl/marvell,armada-xp-pinctrl.txt b/Documentation/devicetree/bindings/pinctrl/marvell,armada-xp-pinctrl.txt new file mode 100644 index 000000000000..bfa0a2e5e0cb --- /dev/null +++ b/Documentation/devicetree/bindings/pinctrl/marvell,armada-xp-pinctrl.txt @@ -0,0 +1,100 @@ +* Marvell Armada XP SoC pinctrl driver for mpp + +Please refer to marvell,mvebu-pinctrl.txt in this directory for common binding +part and usage. + +Required properties: +- compatible: "marvell,mv78230-pinctrl", "marvell,mv78260-pinctrl", + "marvell,mv78460-pinctrl" + +This driver supports all Armada XP variants, i.e. mv78230, mv78260, and mv78460. + +Available mpp pins/groups and functions: +Note: brackets (x) are not part of the mpp name for marvell,function and given +only for more detailed description in this document. + +* Marvell Armada XP (all variants) + +name pins functions +================================================================================ +mpp0 0 gpio, ge0(txclko), lcd(d0) +mpp1 1 gpio, ge0(txd0), lcd(d1) +mpp2 2 gpio, ge0(txd1), lcd(d2) +mpp3 3 gpio, ge0(txd2), lcd(d3) +mpp4 4 gpio, ge0(txd3), lcd(d4) +mpp5 5 gpio, ge0(txctl), lcd(d5) +mpp6 6 gpio, ge0(rxd0), lcd(d6) +mpp7 7 gpio, ge0(rxd1), lcd(d7) +mpp8 8 gpio, ge0(rxd2), lcd(d8) +mpp9 9 gpio, ge0(rxd3), lcd(d9) +mpp10 10 gpio, ge0(rxctl), lcd(d10) +mpp11 11 gpio, ge0(rxclk), lcd(d11) +mpp12 12 gpio, ge0(txd4), ge1(txd0), lcd(d12) +mpp13 13 gpio, ge0(txd5), ge1(txd1), lcd(d13) +mpp14 14 gpio, ge0(txd6), ge1(txd2), lcd(d15) +mpp15 15 gpio, ge0(txd7), ge1(txd3), lcd(d16) +mpp16 16 gpio, ge0(txd7), ge1(txd3), lcd(d16) +mpp17 17 gpio, ge0(col), ge1(txctl), lcd(d17) +mpp18 18 gpio, ge0(rxerr), ge1(rxd0), lcd(d18), ptp(trig) +mpp19 19 gpio, ge0(crs), ge1(rxd1), lcd(d19), ptp(evreq) +mpp20 20 gpio, ge0(rxd4), ge1(rxd2), lcd(d20), ptp(clk) +mpp21 21 gpio, ge0(rxd5), ge1(rxd3), lcd(d21), mem(bat) +mpp22 22 gpio, ge0(rxd6), ge1(rxctl), lcd(d22), sata0(prsnt) +mpp23 23 gpio, ge0(rxd7), ge1(rxclk), lcd(d23), sata1(prsnt) +mpp24 24 gpio, lcd(hsync), sata1(prsnt), nf(bootcs-re), tdm(rst) +mpp25 25 gpio, lcd(vsync), sata0(prsnt), nf(bootcs-we), tdm(pclk) +mpp26 26 gpio, lcd(clk), tdm(fsync), vdd(cpu1-pd) +mpp27 27 gpio, lcd(e), tdm(dtx), ptp(trig) +mpp28 28 gpio, lcd(pwm), tdm(drx), ptp(evreq) +mpp29 29 gpio, lcd(ref-clk), tdm(int0), ptp(clk), vdd(cpu0-pd) +mpp30 30 gpio, tdm(int1), sd0(clk) +mpp31 31 gpio, tdm(int2), sd0(cmd), vdd(cpu0-pd) +mpp32 32 gpio, tdm(int3), sd0(d0), vdd(cpu1-pd) +mpp33 33 gpio, tdm(int4), sd0(d1), mem(bat) +mpp34 34 gpio, tdm(int5), sd0(d2), sata0(prsnt) +mpp35 35 gpio, tdm(int6), sd0(d3), sata1(prsnt) +mpp36 36 gpio, spi(mosi) +mpp37 37 gpio, spi(miso) +mpp38 38 gpio, spi(sck) +mpp39 39 gpio, spi(cs0) +mpp40 40 gpio, spi(cs1), uart2(cts), lcd(vga-hsync), vdd(cpu1-pd), + pcie(clkreq0) +mpp41 41 gpio, spi(cs2), uart2(rts), lcd(vga-vsync), sata1(prsnt), + pcie(clkreq1) +mpp42 42 gpio, uart2(rxd), uart0(cts), tdm(int7), tdm-1(timer), + vdd(cpu0-pd) +mpp43 43 gpio, uart2(txd), uart0(rts), spi(cs3), pcie(rstout), + vdd(cpu2-3-pd){1} +mpp44 44 gpio, uart2(cts), uart3(rxd), spi(cs4), pcie(clkreq2), + mem(bat) +mpp45 45 gpio, uart2(rts), uart3(txd), spi(cs5), sata1(prsnt) +mpp46 46 gpio, uart3(rts), uart1(rts), spi(cs6), sata0(prsnt) +mpp47 47 gpio, uart3(cts), uart1(cts), spi(cs7), pcie(clkreq3), + ref(clkout) +mpp48 48 gpio, tclk, dev(burst/last) + +* Marvell Armada XP (mv78260 and mv78460 only) + +name pins functions +================================================================================ +mpp49 49 gpio, dev(we3) +mpp50 50 gpio, dev(we2) +mpp51 51 gpio, dev(ad16) +mpp52 52 gpio, dev(ad17) +mpp53 53 gpio, dev(ad18) +mpp54 54 gpio, dev(ad19) +mpp55 55 gpio, dev(ad20), vdd(cpu0-pd) +mpp56 56 gpio, dev(ad21), vdd(cpu1-pd) +mpp57 57 gpio, dev(ad22), vdd(cpu2-3-pd){1} +mpp58 58 gpio, dev(ad23) +mpp59 59 gpio, dev(ad24) +mpp60 60 gpio, dev(ad25) +mpp61 61 gpio, dev(ad26) +mpp62 62 gpio, dev(ad27) +mpp63 63 gpio, dev(ad28) +mpp64 64 gpio, dev(ad29) +mpp65 65 gpio, dev(ad30) +mpp66 66 gpio, dev(ad31) + +Notes: +* {1} vdd(cpu2-3-pd) only available on mv78460. diff --git a/Documentation/devicetree/bindings/pinctrl/marvell,dove-pinctrl.txt b/Documentation/devicetree/bindings/pinctrl/marvell,dove-pinctrl.txt new file mode 100644 index 000000000000..a648aaad6110 --- /dev/null +++ b/Documentation/devicetree/bindings/pinctrl/marvell,dove-pinctrl.txt @@ -0,0 +1,72 @@ +* Marvell Dove SoC pinctrl driver for mpp + +Please refer to marvell,mvebu-pinctrl.txt in this directory for common binding +part and usage. + +Required properties: +- compatible: "marvell,dove-pinctrl" +- clocks: (optional) phandle of pdma clock + +Available mpp pins/groups and functions: +Note: brackets (x) are not part of the mpp name for marvell,function and given +only for more detailed description in this document. + +name pins functions +================================================================================ +mpp0 0 gpio, pmu, uart2(rts), sdio0(cd), lcd0(pwm) +mpp1 1 gpio, pmu, uart2(cts), sdio0(wp), lcd1(pwm) +mpp2 2 gpio, pmu, uart2(txd), sdio0(buspwr), sata(prsnt), + uart1(rts) +mpp3 3 gpio, pmu, uart2(rxd), sdio0(ledctrl), sata(act), + uart1(cts), lcd-spi(cs1) +mpp4 4 gpio, pmu, uart3(rts), sdio1(cd), spi1(miso) +mpp5 5 gpio, pmu, uart3(cts), sdio1(wp), spi1(cs) +mpp6 6 gpio, pmu, uart3(txd), sdio1(buspwr), spi1(mosi) +mpp7 7 gpio, pmu, uart3(rxd), sdio1(ledctrl), spi1(sck) +mpp8 8 gpio, pmu, watchdog(rstout) +mpp9 9 gpio, pmu, pex1(clkreq) +mpp10 10 gpio, pmu, ssp(sclk) +mpp11 11 gpio, pmu, sata(prsnt), sata-1(act), sdio0(ledctrl), + sdio1(ledctrl), pex0(clkreq) +mpp12 12 gpio, pmu, uart2(rts), audio0(extclk), sdio1(cd), sata(act) +mpp13 13 gpio, pmu, uart2(cts), audio1(extclk), sdio1(wp), + ssp(extclk) +mpp14 14 gpio, pmu, uart2(txd), sdio1(buspwr), ssp(rxd) +mpp15 15 gpio, pmu, uart2(rxd), sdio1(ledctrl), ssp(sfrm) +mpp16 16 gpio, uart3(rts), sdio0(cd), ac97(sdi1), lcd-spi(cs1) +mpp17 17 gpio, uart3(cts), sdio0(wp), ac97(sdi2), twsi(sda), + ac97-1(sysclko) +mpp18 18 gpio, uart3(txd), sdio0(buspwr), ac97(sdi3), lcd0(pwm) +mpp19 19 gpio, uart3(rxd), sdio0(ledctrl), twsi(sck) +mpp20 20 gpio, sdio0(cd), sdio1(cd), spi1(miso), lcd-spi(miso), + ac97(sysclko) +mpp21 21 gpio, sdio0(wp), sdio1(wp), spi1(cs), lcd-spi(cs0), + uart1(cts), ssp(sfrm) +mpp22 22 gpio, sdio0(buspwr), sdio1(buspwr), spi1(mosi), + lcd-spi(mosi), uart1(cts), ssp(txd) +mpp23 23 gpio, sdio0(ledctrl), sdio1(ledctrl), spi1(sck), + lcd-spi(sck), ssp(sclk) +mpp_camera 24-39 gpio, camera +mpp_sdio0 40-45 gpio, sdio0 +mpp_sdio1 46-51 gpio, sdio1 +mpp_audio1 52-57 gpio, i2s1/spdifo, i2s1, spdifo, twsi, ssp/spdifo, ssp, + ssp/twsi +mpp_spi0 58-61 gpio, spi0 +mpp_uart1 62-63 gpio, uart1 +mpp_nand 64-71 gpo, nand +audio0 - i2s, ac97 +twsi - none, opt1, opt2, opt3 + +Notes: +* group "mpp_audio1" allows the following functions and gpio pins: + - gpio : gpio on pins 52-57 + - i2s1/spdifo : audio1 i2s on pins 52-55 and spdifo on 57, no gpios + - i2s1 : audio1 i2s on pins 52-55, gpio on pins 56,57 + - spdifo : spdifo on pin 57, gpio on pins 52-55 + - twsi : twsi on pins 56,57, gpio on pins 52-55 + - ssp/spdifo : ssp on pins 52-55, spdifo on pin 57, no gpios + - ssp : ssp on pins 52-55, gpio on pins 56,57 + - ssp/twsi : ssp on pins 52-55, twsi on pins 56,57, no gpios +* group "audio0" internally muxes i2s0 or ac97 controller to the dedicated + audio0 pins. +* group "twsi" internally muxes twsi controller to the dedicated or option pins. diff --git a/Documentation/devicetree/bindings/pinctrl/marvell,kirkwood-pinctrl.txt b/Documentation/devicetree/bindings/pinctrl/marvell,kirkwood-pinctrl.txt new file mode 100644 index 000000000000..361bccb7ec89 --- /dev/null +++ b/Documentation/devicetree/bindings/pinctrl/marvell,kirkwood-pinctrl.txt @@ -0,0 +1,279 @@ +* Marvell Kirkwood SoC pinctrl driver for mpp + +Please refer to marvell,mvebu-pinctrl.txt in this directory for common binding +part and usage. + +Required properties: +- compatible: "marvell,88f6180-pinctrl", + "marvell,88f6190-pinctrl", "marvell,88f6192-pinctrl", + "marvell,88f6281-pinctrl", "marvell,88f6282-pinctrl" + +This driver supports all kirkwood variants, i.e. 88f6180, 88f619x, and 88f628x. + +Available mpp pins/groups and functions: +Note: brackets (x) are not part of the mpp name for marvell,function and given +only for more detailed description in this document. + +* Marvell Kirkwood 88f6180 + +name pins functions +================================================================================ +mpp0 0 gpio, nand(io2), spi(cs) +mpp1 1 gpo, nand(io3), spi(mosi) +mpp2 2 gpo, nand(io4), spi(sck) +mpp3 3 gpo, nand(io5), spi(miso) +mpp4 4 gpio, nand(io6), uart0(rxd), ptp(clk) +mpp5 5 gpo, nand(io7), uart0(txd), ptp(trig) +mpp6 6 sysrst(out), spi(mosi), ptp(trig) +mpp7 7 gpo, pex(rsto), spi(cs), ptp(trig) +mpp8 8 gpio, twsi0(sda), uart0(rts), uart1(rts), ptp(clk), + mii(col) +mpp9 9 gpio, twsi(sck), uart0(cts), uart1(cts), ptp(evreq), + mii(crs) +mpp10 10 gpo, spi(sck), uart0(txd), ptp(trig) +mpp11 11 gpio, spi(miso), uart0(rxd), ptp(clk), ptp-1(evreq), + ptp-2(trig) +mpp12 12 gpo, sdio(clk) +mpp13 13 gpio, sdio(cmd), uart1(txd) +mpp14 14 gpio, sdio(d0), uart1(rxd), mii(col) +mpp15 15 gpio, sdio(d1), uart0(rts), uart1(txd) +mpp16 16 gpio, sdio(d2), uart0(cts), uart1(rxd), mii(crs) +mpp17 17 gpio, sdio(d3) +mpp18 18 gpo, nand(io0) +mpp19 19 gpo, nand(io1) +mpp20 20 gpio, mii(rxerr) +mpp21 21 gpio, audio(spdifi) +mpp22 22 gpio, audio(spdifo) +mpp23 23 gpio, audio(rmclk) +mpp24 24 gpio, audio(bclk) +mpp25 25 gpio, audio(sdo) +mpp26 26 gpio, audio(lrclk) +mpp27 27 gpio, audio(mclk) +mpp28 28 gpio, audio(sdi) +mpp29 29 gpio, audio(extclk) + +* Marvell Kirkwood 88f6190 + +name pins functions +================================================================================ +mpp0 0 gpio, nand(io2), spi(cs) +mpp1 1 gpo, nand(io3), spi(mosi) +mpp2 2 gpo, nand(io4), spi(sck) +mpp3 3 gpo, nand(io5), spi(miso) +mpp4 4 gpio, nand(io6), uart0(rxd), ptp(clk) +mpp5 5 gpo, nand(io7), uart0(txd), ptp(trig), sata0(act) +mpp6 6 sysrst(out), spi(mosi), ptp(trig) +mpp7 7 gpo, pex(rsto), spi(cs), ptp(trig) +mpp8 8 gpio, twsi0(sda), uart0(rts), uart1(rts), ptp(clk), + mii(col), mii-1(rxerr) +mpp9 9 gpio, twsi(sck), uart0(cts), uart1(cts), ptp(evreq), + mii(crs), sata0(prsnt) +mpp10 10 gpo, spi(sck), uart0(txd), ptp(trig) +mpp11 11 gpio, spi(miso), uart0(rxd), ptp(clk), ptp-1(evreq), + ptp-2(trig), sata0(act) +mpp12 12 gpo, sdio(clk) +mpp13 13 gpio, sdio(cmd), uart1(txd) +mpp14 14 gpio, sdio(d0), uart1(rxd), mii(col) +mpp15 15 gpio, sdio(d1), uart0(rts), uart1(txd), sata0(act) +mpp16 16 gpio, sdio(d2), uart0(cts), uart1(rxd), mii(crs) +mpp17 17 gpio, sdio(d3), sata0(prsnt) +mpp18 18 gpo, nand(io0) +mpp19 19 gpo, nand(io1) +mpp20 20 gpio, ge1(txd0) +mpp21 21 gpio, ge1(txd1), sata0(act) +mpp22 22 gpio, ge1(txd2) +mpp23 23 gpio, ge1(txd3), sata0(prsnt) +mpp24 24 gpio, ge1(rxd0) +mpp25 25 gpio, ge1(rxd1) +mpp26 26 gpio, ge1(rxd2) +mpp27 27 gpio, ge1(rxd3) +mpp28 28 gpio, ge1(col) +mpp29 29 gpio, ge1(txclk) +mpp30 30 gpio, ge1(rxclk) +mpp31 31 gpio, ge1(rxclk) +mpp32 32 gpio, ge1(txclko) +mpp33 33 gpo, ge1(txclk) +mpp34 34 gpio, ge1(txen) +mpp35 35 gpio, ge1(rxerr), sata0(act), mii(rxerr) + +* Marvell Kirkwood 88f6192 + +name pins functions +================================================================================ +mpp0 0 gpio, nand(io2), spi(cs) +mpp1 1 gpo, nand(io3), spi(mosi) +mpp2 2 gpo, nand(io4), spi(sck) +mpp3 3 gpo, nand(io5), spi(miso) +mpp4 4 gpio, nand(io6), uart0(rxd), ptp(clk), sata1(act) +mpp5 5 gpo, nand(io7), uart0(txd), ptp(trig), sata0(act) +mpp6 6 sysrst(out), spi(mosi), ptp(trig) +mpp7 7 gpo, pex(rsto), spi(cs), ptp(trig) +mpp8 8 gpio, twsi0(sda), uart0(rts), uart1(rts), ptp(clk), + mii(col), mii-1(rxerr), sata1(prsnt) +mpp9 9 gpio, twsi(sck), uart0(cts), uart1(cts), ptp(evreq), + mii(crs), sata0(prsnt) +mpp10 10 gpo, spi(sck), uart0(txd), ptp(trig), sata1(act) +mpp11 11 gpio, spi(miso), uart0(rxd), ptp(clk), ptp-1(evreq), + ptp-2(trig), sata0(act) +mpp12 12 gpo, sdio(clk) +mpp13 13 gpio, sdio(cmd), uart1(txd) +mpp14 14 gpio, sdio(d0), uart1(rxd), mii(col), sata1(prsnt) +mpp15 15 gpio, sdio(d1), uart0(rts), uart1(txd), sata0(act) +mpp16 16 gpio, sdio(d2), uart0(cts), uart1(rxd), mii(crs), + sata1(act) +mpp17 17 gpio, sdio(d3), sata0(prsnt) +mpp18 18 gpo, nand(io0) +mpp19 19 gpo, nand(io1) +mpp20 20 gpio, ge1(txd0), ts(mp0), tdm(tx0ql), audio(spdifi), + sata1(act) +mpp21 21 gpio, ge1(txd1), sata0(act), ts(mp1), tdm(rx0ql), + audio(spdifo) +mpp22 22 gpio, ge1(txd2), ts(mp2), tdm(tx2ql), audio(rmclk), + sata1(prsnt) +mpp23 23 gpio, ge1(txd3), sata0(prsnt), ts(mp3), tdm(rx2ql), + audio(bclk) +mpp24 24 gpio, ge1(rxd0), ts(mp4), tdm(spi-cs0), audio(sdo) +mpp25 25 gpio, ge1(rxd1), ts(mp5), tdm(spi-sck), audio(lrclk) +mpp26 26 gpio, ge1(rxd2), ts(mp6), tdm(spi-miso), audio(mclk) +mpp27 27 gpio, ge1(rxd3), ts(mp7), tdm(spi-mosi), audio(sdi) +mpp28 28 gpio, ge1(col), ts(mp8), tdm(int), audio(extclk) +mpp29 29 gpio, ge1(txclk), ts(mp9), tdm(rst) +mpp30 30 gpio, ge1(rxclk), ts(mp10), tdm(pclk) +mpp31 31 gpio, ge1(rxclk), ts(mp11), tdm(fs) +mpp32 32 gpio, ge1(txclko), ts(mp12), tdm(drx) +mpp33 33 gpo, ge1(txclk), tdm(drx) +mpp34 34 gpio, ge1(txen), tdm(spi-cs1) +mpp35 35 gpio, ge1(rxerr), sata0(act), mii(rxerr), tdm(tx0ql) + +* Marvell Kirkwood 88f6281 + +name pins functions +================================================================================ +mpp0 0 gpio, nand(io2), spi(cs) +mpp1 1 gpo, nand(io3), spi(mosi) +mpp2 2 gpo, nand(io4), spi(sck) +mpp3 3 gpo, nand(io5), spi(miso) +mpp4 4 gpio, nand(io6), uart0(rxd), ptp(clk), sata1(act) +mpp5 5 gpo, nand(io7), uart0(txd), ptp(trig), sata0(act) +mpp6 6 sysrst(out), spi(mosi), ptp(trig) +mpp7 7 gpo, pex(rsto), spi(cs), ptp(trig) +mpp8 8 gpio, twsi0(sda), uart0(rts), uart1(rts), ptp(clk), + mii(col), mii-1(rxerr), sata1(prsnt) +mpp9 9 gpio, twsi(sck), uart0(cts), uart1(cts), ptp(evreq), + mii(crs), sata0(prsnt) +mpp10 10 gpo, spi(sck), uart0(txd), ptp(trig), sata1(act) +mpp11 11 gpio, spi(miso), uart0(rxd), ptp(clk), ptp-1(evreq), + ptp-2(trig), sata0(act) +mpp12 12 gpio, sdio(clk) +mpp13 13 gpio, sdio(cmd), uart1(txd) +mpp14 14 gpio, sdio(d0), uart1(rxd), mii(col), sata1(prsnt) +mpp15 15 gpio, sdio(d1), uart0(rts), uart1(txd), sata0(act) +mpp16 16 gpio, sdio(d2), uart0(cts), uart1(rxd), mii(crs), + sata1(act) +mpp17 17 gpio, sdio(d3), sata0(prsnt) +mpp18 18 gpo, nand(io0) +mpp19 19 gpo, nand(io1) +mpp20 20 gpio, ge1(txd0), ts(mp0), tdm(tx0ql), audio(spdifi), + sata1(act) +mpp21 21 gpio, ge1(txd1), sata0(act), ts(mp1), tdm(rx0ql), + audio(spdifo) +mpp22 22 gpio, ge1(txd2), ts(mp2), tdm(tx2ql), audio(rmclk), + sata1(prsnt) +mpp23 23 gpio, ge1(txd3), sata0(prsnt), ts(mp3), tdm(rx2ql), + audio(bclk) +mpp24 24 gpio, ge1(rxd0), ts(mp4), tdm(spi-cs0), audio(sdo) +mpp25 25 gpio, ge1(rxd1), ts(mp5), tdm(spi-sck), audio(lrclk) +mpp26 26 gpio, ge1(rxd2), ts(mp6), tdm(spi-miso), audio(mclk) +mpp27 27 gpio, ge1(rxd3), ts(mp7), tdm(spi-mosi), audio(sdi) +mpp28 28 gpio, ge1(col), ts(mp8), tdm(int), audio(extclk) +mpp29 29 gpio, ge1(txclk), ts(mp9), tdm(rst) +mpp30 30 gpio, ge1(rxclk), ts(mp10), tdm(pclk) +mpp31 31 gpio, ge1(rxclk), ts(mp11), tdm(fs) +mpp32 32 gpio, ge1(txclko), ts(mp12), tdm(drx) +mpp33 33 gpo, ge1(txclk), tdm(drx) +mpp34 34 gpio, ge1(txen), tdm(spi-cs1), sata1(act) +mpp35 35 gpio, ge1(rxerr), sata0(act), mii(rxerr), tdm(tx0ql) +mpp36 36 gpio, ts(mp0), tdm(spi-cs1), audio(spdifi) +mpp37 37 gpio, ts(mp1), tdm(tx2ql), audio(spdifo) +mpp38 38 gpio, ts(mp2), tdm(rx2ql), audio(rmclk) +mpp39 39 gpio, ts(mp3), tdm(spi-cs0), audio(bclk) +mpp40 40 gpio, ts(mp4), tdm(spi-sck), audio(sdo) +mpp41 41 gpio, ts(mp5), tdm(spi-miso), audio(lrclk) +mpp42 42 gpio, ts(mp6), tdm(spi-mosi), audio(mclk) +mpp43 43 gpio, ts(mp7), tdm(int), audio(sdi) +mpp44 44 gpio, ts(mp8), tdm(rst), audio(extclk) +mpp45 45 gpio, ts(mp9), tdm(pclk) +mpp46 46 gpio, ts(mp10), tdm(fs) +mpp47 47 gpio, ts(mp11), tdm(drx) +mpp48 48 gpio, ts(mp12), tdm(dtx) +mpp49 49 gpio, ts(mp9), tdm(rx0ql), ptp(clk) + +* Marvell Kirkwood 88f6282 + +name pins functions +================================================================================ +mpp0 0 gpio, nand(io2), spi(cs) +mpp1 1 gpo, nand(io3), spi(mosi) +mpp2 2 gpo, nand(io4), spi(sck) +mpp3 3 gpo, nand(io5), spi(miso) +mpp4 4 gpio, nand(io6), uart0(rxd), sata1(act), lcd(hsync) +mpp5 5 gpo, nand(io7), uart0(txd), sata0(act), lcd(vsync) +mpp6 6 sysrst(out), spi(mosi) +mpp7 7 gpo, spi(cs), lcd(pwm) +mpp8 8 gpio, twsi0(sda), uart0(rts), uart1(rts), mii(col), + mii-1(rxerr), sata1(prsnt) +mpp9 9 gpio, twsi(sck), uart0(cts), uart1(cts), mii(crs), + sata0(prsnt) +mpp10 10 gpo, spi(sck), uart0(txd), sata1(act) +mpp11 11 gpio, spi(miso), uart0(rxd), sata0(act) +mpp12 12 gpo, sdio(clk), audio(spdifo), spi(mosi), twsi(sda) +mpp13 13 gpio, sdio(cmd), uart1(txd), audio(rmclk), lcd(pwm) +mpp14 14 gpio, sdio(d0), uart1(rxd), mii(col), sata1(prsnt), + audio(spdifi), audio-1(sdi) +mpp15 15 gpio, sdio(d1), uart0(rts), uart1(txd), sata0(act), + spi(cs) +mpp16 16 gpio, sdio(d2), uart0(cts), uart1(rxd), mii(crs), + sata1(act), lcd(extclk) +mpp17 17 gpio, sdio(d3), sata0(prsnt), sata1(act), twsi1(sck) +mpp18 18 gpo, nand(io0), pex(clkreq) +mpp19 19 gpo, nand(io1) +mpp20 20 gpio, ge1(txd0), ts(mp0), tdm(tx0ql), audio(spdifi), + sata1(act), lcd(d0) +mpp21 21 gpio, ge1(txd1), sata0(act), ts(mp1), tdm(rx0ql), + audio(spdifo), lcd(d1) +mpp22 22 gpio, ge1(txd2), ts(mp2), tdm(tx2ql), audio(rmclk), + sata1(prsnt), lcd(d2) +mpp23 23 gpio, ge1(txd3), sata0(prsnt), ts(mp3), tdm(rx2ql), + audio(bclk), lcd(d3) +mpp24 24 gpio, ge1(rxd0), ts(mp4), tdm(spi-cs0), audio(sdo), + lcd(d4) +mpp25 25 gpio, ge1(rxd1), ts(mp5), tdm(spi-sck), audio(lrclk), + lcd(d5) +mpp26 26 gpio, ge1(rxd2), ts(mp6), tdm(spi-miso), audio(mclk), + lcd(d6) +mpp27 27 gpio, ge1(rxd3), ts(mp7), tdm(spi-mosi), audio(sdi), + lcd(d7) +mpp28 28 gpio, ge1(col), ts(mp8), tdm(int), audio(extclk), + lcd(d8) +mpp29 29 gpio, ge1(txclk), ts(mp9), tdm(rst), lcd(d9) +mpp30 30 gpio, ge1(rxclk), ts(mp10), tdm(pclk), lcd(d10) +mpp31 31 gpio, ge1(rxclk), ts(mp11), tdm(fs), lcd(d11) +mpp32 32 gpio, ge1(txclko), ts(mp12), tdm(drx), lcd(d12) +mpp33 33 gpo, ge1(txclk), tdm(drx), lcd(d13) +mpp34 34 gpio, ge1(txen), tdm(spi-cs1), sata1(act), lcd(d14) +mpp35 35 gpio, ge1(rxerr), sata0(act), mii(rxerr), tdm(tx0ql), + lcd(d15) +mpp36 36 gpio, ts(mp0), tdm(spi-cs1), audio(spdifi), twsi1(sda) +mpp37 37 gpio, ts(mp1), tdm(tx2ql), audio(spdifo), twsi1(sck) +mpp38 38 gpio, ts(mp2), tdm(rx2ql), audio(rmclk), lcd(d18) +mpp39 39 gpio, ts(mp3), tdm(spi-cs0), audio(bclk), lcd(d19) +mpp40 40 gpio, ts(mp4), tdm(spi-sck), audio(sdo), lcd(d20) +mpp41 41 gpio, ts(mp5), tdm(spi-miso), audio(lrclk), lcd(d21) +mpp42 42 gpio, ts(mp6), tdm(spi-mosi), audio(mclk), lcd(d22) +mpp43 43 gpio, ts(mp7), tdm(int), audio(sdi), lcd(d23) +mpp44 44 gpio, ts(mp8), tdm(rst), audio(extclk), lcd(clk) +mpp45 45 gpio, ts(mp9), tdm(pclk), lcd(e) +mpp46 46 gpio, ts(mp10), tdm(fs), lcd(hsync) +mpp47 47 gpio, ts(mp11), tdm(drx), lcd(vsync) +mpp48 48 gpio, ts(mp12), tdm(dtx), lcd(d16) +mpp49 49 gpo, tdm(rx0ql), pex(clkreq), lcd(d17) diff --git a/Documentation/devicetree/bindings/pinctrl/marvell,mvebu-pinctrl.txt b/Documentation/devicetree/bindings/pinctrl/marvell,mvebu-pinctrl.txt new file mode 100644 index 000000000000..0a26c3aa4e6d --- /dev/null +++ b/Documentation/devicetree/bindings/pinctrl/marvell,mvebu-pinctrl.txt @@ -0,0 +1,46 @@ +* Marvell SoC pinctrl core driver for mpp + +The pinctrl driver enables Marvell SoCs to configure the multi-purpose pins +(mpp) to a specific function. For each SoC family there is a SoC specific +driver using this core driver. + +Please refer to pinctrl-bindings.txt in this directory for details of the +common pinctrl bindings used by client devices, including the meaning of the +phrase "pin configuration node". + +A Marvell SoC pin configuration node is a node of a group of pins which can +be used for a specific device or function. Each node requires one or more +mpp pins or group of pins and a mpp function common to all pins. + +Required properties for pinctrl driver: +- compatible: "marvell,<soc>-pinctrl" + Please refer to each marvell,<soc>-pinctrl.txt binding doc for supported SoCs. + +Required properties for pin configuration node: +- marvell,pins: string array of mpp pins or group of pins to be muxed. +- marvell,function: string representing a function to mux to for all + marvell,pins given in this pin configuration node. The function has to be + common for all marvell,pins. Please refer to marvell,<soc>-pinctrl.txt for + valid pin/pin group names and available function names for each SoC. + +Examples: + +uart1: serial@12100 { + compatible = "ns16550a"; + reg = <0x12100 0x100>; + reg-shift = <2>; + interrupts = <7>; + + pinctrl-0 = <&pmx_uart1_sw>; + pinctrl-names = "default"; +}; + +pinctrl: pinctrl@d0200 { + compatible = "marvell,dove-pinctrl"; + reg = <0xd0200 0x20>; + + pmx_uart1_sw: pmx-uart1-sw { + marvell,pins = "mpp_uart1"; + marvell,function = "uart1"; + }; +}; diff --git a/Documentation/devicetree/bindings/powerpc/fsl/ifc.txt b/Documentation/devicetree/bindings/powerpc/fsl/ifc.txt index 939a26d541f6..d5e370450ac0 100644 --- a/Documentation/devicetree/bindings/powerpc/fsl/ifc.txt +++ b/Documentation/devicetree/bindings/powerpc/fsl/ifc.txt @@ -12,9 +12,12 @@ Properties: - #size-cells : Either one or two, depending on how large each chipselect can be. - reg : Offset and length of the register set for the device -- interrupts : IFC has two interrupts. The first one is the "common" - interrupt(CM_EVTER_STAT), and second is the NAND interrupt - (NAND_EVTER_STAT). +- interrupts: IFC may have one or two interrupts. If two interrupt + specifiers are present, the first is the "common" + interrupt (CM_EVTER_STAT), and the second is the NAND + interrupt (NAND_EVTER_STAT). If there is only one, + that interrupt reports both types of event. + - ranges : Each range corresponds to a single chipselect, and covers the entire access window as configured. diff --git a/Documentation/devicetree/bindings/pwm/imx-pwm.txt b/Documentation/devicetree/bindings/pwm/imx-pwm.txt new file mode 100644 index 000000000000..8522bfbccfd7 --- /dev/null +++ b/Documentation/devicetree/bindings/pwm/imx-pwm.txt @@ -0,0 +1,17 @@ +Freescale i.MX PWM controller + +Required properties: +- compatible: should be "fsl,<soc>-pwm" +- reg: physical base address and length of the controller's registers +- #pwm-cells: should be 2. The first cell specifies the per-chip index + of the PWM to use and the second cell is the period in nanoseconds. +- interrupts: The interrupt for the pwm controller + +Example: + +pwm1: pwm@53fb4000 { + #pwm-cells = <2>; + compatible = "fsl,imx53-pwm", "fsl,imx27-pwm"; + reg = <0x53fb4000 0x4000>; + interrupts = <61>; +}; diff --git a/Documentation/devicetree/bindings/pwm/mxs-pwm.txt b/Documentation/devicetree/bindings/pwm/mxs-pwm.txt index 11963e4d6bc4..9e3f8f1d46a2 100644 --- a/Documentation/devicetree/bindings/pwm/mxs-pwm.txt +++ b/Documentation/devicetree/bindings/pwm/mxs-pwm.txt @@ -4,7 +4,7 @@ Required properties: - compatible: should be "fsl,imx23-pwm" - reg: physical base address and length of the controller's registers - #pwm-cells: should be 2. The first cell specifies the per-chip index - of the PWM to use and the second cell is the duty cycle in nanoseconds. + of the PWM to use and the second cell is the period in nanoseconds. - fsl,pwm-number: the number of PWM devices Example: diff --git a/Documentation/devicetree/bindings/pwm/nvidia,tegra20-pwm.txt b/Documentation/devicetree/bindings/pwm/nvidia,tegra20-pwm.txt index bbbeedb4ec05..01438ecd6628 100644 --- a/Documentation/devicetree/bindings/pwm/nvidia,tegra20-pwm.txt +++ b/Documentation/devicetree/bindings/pwm/nvidia,tegra20-pwm.txt @@ -7,7 +7,7 @@ Required properties: - reg: physical base address and length of the controller's registers - #pwm-cells: On Tegra the number of cells used to specify a PWM is 2. The first cell specifies the per-chip index of the PWM to use and the second - cell is the duty cycle in nanoseconds. + cell is the period in nanoseconds. Example: diff --git a/Documentation/devicetree/bindings/regulator/88pm860x.txt b/Documentation/devicetree/bindings/regulator/88pm860x.txt new file mode 100644 index 000000000000..1267b3e1a2cc --- /dev/null +++ b/Documentation/devicetree/bindings/regulator/88pm860x.txt @@ -0,0 +1,30 @@ +Marvell 88PM860x regulator + +Required properties: +- compatible: "marvell,88pm860x" +- reg: I2C slave address +- regulators: A node that houses a sub-node for each regulator within the + device. Each sub-node is identified using the regulator-compatible + property, with valid values listed below. + +Example: + + pmic: 88pm860x@34 { + compatible = "marvell,88pm860x"; + reg = <0x34>; + + regulators { + BUCK1 { + regulator-min-microvolt = <1000000>; + regulator-max-microvolt = <1500000>; + regulator-boot-on; + regulator-always-on; + }; + BUCK3 { + regulator-min-microvolt = <1000000>; + regulator-max-microvolt = <3000000>; + regulator-boot-on; + regulator-always-on; + }; + }; + }; diff --git a/Documentation/devicetree/bindings/regulator/max8907.txt b/Documentation/devicetree/bindings/regulator/max8907.txt new file mode 100644 index 000000000000..371eccd1cd68 --- /dev/null +++ b/Documentation/devicetree/bindings/regulator/max8907.txt @@ -0,0 +1,69 @@ +MAX8907 regulator + +Required properties: +- compatible: "maxim,max8907" +- reg: I2C slave address +- interrupts: The interrupt output of the controller +- mbatt-supply: The input supply for MBATT, BBAT, SDBY, VRTC. +- in-v1-supply: The input supply for SD1. +- in-v2-supply: The input supply for SD2. +- in-v3-supply: The input supply for SD3. +- in1-supply: The input supply for LDO1. +... +- in20-supply: The input supply for LDO20. +- regulators: A node that houses a sub-node for each regulator within the + device. Each sub-node is identified using the node's name (or the deprecated + regulator-compatible property if present), with valid values listed below. + The content of each sub-node is defined by the standard binding for + regulators; see regulator.txt. + +Optional properties: +- maxim,system-power-controller: Boolean property indicating that the PMIC + controls the overall system power. + +The valid names for regulators are: + + sd1, sd2, sd3, ldo1, ldo2, ldo3, ldo4, ldo5, ldo6, ldo7, ldo8, ldo9, ldo10, + ldo11, ldo12, ldo13, ldo14, ldo15, ldo16, ldo17, ldo18, ldo19, ldo20, out5v, + out33v, bbat, sdby, vrtc. + +Example: + + max8907@3c { + compatible = "maxim,max8907"; + reg = <0x3c>; + interrupts = <0 86 0x4>; + + maxim,system-power-controller; + + mbatt-supply = <&some_reg>; + in-v1-supply = <&mbatt_reg>; + ... + in1-supply = <&mbatt_reg>; + ... + + regulators { + mbatt_reg: mbatt { + regulator-name = "vbat_pmu"; + regulator-min-microvolt = <5000000>; + regulator-max-microvolt = <5000000>; + regulator-always-on; + }; + + sd1 { + regulator-name = "nvvdd_sv1,vdd_cpu_pmu"; + regulator-min-microvolt = <1000000>; + regulator-max-microvolt = <1000000>; + regulator-always-on; + }; + + sd2 { + regulator-name = "nvvdd_sv2,vdd_core"; + regulator-min-microvolt = <1200000>; + regulator-max-microvolt = <1200000>; + regulator-always-on; + }; +... + }; + }; + }; diff --git a/Documentation/devicetree/bindings/regulator/tps6586x.txt b/Documentation/devicetree/bindings/regulator/tps6586x.txt index 07b9ef6e49d5..8b40cac24d93 100644 --- a/Documentation/devicetree/bindings/regulator/tps6586x.txt +++ b/Documentation/devicetree/bindings/regulator/tps6586x.txt @@ -22,6 +22,10 @@ Required properties: - vinldo678-supply: The input supply for the LDO6, LDO7 and LDO8 - vinldo9-supply: The input supply for the LDO9 +Optional properties: +- ti,system-power-controller: Telling whether or not this pmic is controlling + the system power. + Each regulator is defined using the standard binding for regulators. Note: LDO5 and LDO_RTC is supplied by SYS regulator internally and driver @@ -37,6 +41,8 @@ Example: #gpio-cells = <2>; gpio-controller; + ti,system-power-controller; + sys-supply = <&some_reg>; vin-sm0-supply = <&some_reg>; vin-sm1-supply = <&some_reg>; diff --git a/Documentation/devicetree/bindings/rtc/snvs-rtc.txt b/Documentation/devicetree/bindings/rtc/snvs-rtc.txt new file mode 100644 index 000000000000..fb61ed77ada3 --- /dev/null +++ b/Documentation/devicetree/bindings/rtc/snvs-rtc.txt @@ -0,0 +1 @@ +See Documentation/devicetree/bindings/crypto/fsl-sec4.txt for details. diff --git a/Documentation/devicetree/bindings/sound/cs4270.txt b/Documentation/devicetree/bindings/sound/cs4270.txt new file mode 100644 index 000000000000..6b222f9b8ef5 --- /dev/null +++ b/Documentation/devicetree/bindings/sound/cs4270.txt @@ -0,0 +1,21 @@ +CS4270 audio CODEC + +The driver for this device currently only supports I2C. + +Required properties: + + - compatible : "cirrus,cs4270" + + - reg : the I2C address of the device for I2C + +Optional properties: + + - reset-gpio : a GPIO spec for the reset pin. If specified, it will be + deasserted before communication to the codec starts. + +Example: + +codec: cs4270@48 { + compatible = "cirrus,cs4270"; + reg = <0x48>; +}; diff --git a/Documentation/devicetree/bindings/sound/cs4271.txt b/Documentation/devicetree/bindings/sound/cs4271.txt new file mode 100644 index 000000000000..c81b5fd5a5bc --- /dev/null +++ b/Documentation/devicetree/bindings/sound/cs4271.txt @@ -0,0 +1,36 @@ +Cirrus Logic CS4271 DT bindings + +This driver supports both the I2C and the SPI bus. + +Required properties: + + - compatible: "cirrus,cs4271" + +For required properties on SPI, please consult +Documentation/devicetree/bindings/spi/spi-bus.txt + +Required properties on I2C: + + - reg: the i2c address + + +Optional properties: + + - reset-gpio: a GPIO spec to define which pin is connected to the chip's + !RESET pin + +Examples: + + codec_i2c: cs4271@10 { + compatible = "cirrus,cs4271"; + reg = <0x10>; + reset-gpio = <&gpio 23 0>; + }; + + codec_spi: cs4271@0 { + compatible = "cirrus,cs4271"; + reg = <0x0>; + reset-gpio = <&gpio 23 0>; + spi-max-frequency = <6000000>; + }; + diff --git a/Documentation/devicetree/bindings/sound/davinci-mcasp-audio.txt b/Documentation/devicetree/bindings/sound/davinci-mcasp-audio.txt new file mode 100644 index 000000000000..374e145c2ef1 --- /dev/null +++ b/Documentation/devicetree/bindings/sound/davinci-mcasp-audio.txt @@ -0,0 +1,45 @@ +Texas Instruments McASP controller + +Required properties: +- compatible : + "ti,dm646x-mcasp-audio" : for DM646x platforms + "ti,da830-mcasp-audio" : for both DA830 & DA850 platforms + "ti,omap2-mcasp-audio" : for OMAP2 platforms (TI81xx, AM33xx) + +- reg : Should contain McASP registers offset and length +- interrupts : Interrupt number for McASP +- op-mode : I2S/DIT ops mode. +- tdm-slots : Slots for TDM operation. +- num-serializer : Serializers used by McASP. +- serial-dir : A list of serializer pin mode. The list number should be equal + to "num-serializer" parameter. Each entry is a number indication + serializer pin direction. (0 - INACTIVE, 1 - TX, 2 - RX) + + +Optional properties: + +- ti,hwmods : Must be "mcasp<n>", n is controller instance starting 0 +- tx-num-evt : FIFO levels. +- rx-num-evt : FIFO levels. +- sram-size-playback : size of sram to be allocated during playback +- sram-size-capture : size of sram to be allocated during capture + +Example: + +mcasp0: mcasp0@1d00000 { + compatible = "ti,da830-mcasp-audio"; + #address-cells = <1>; + #size-cells = <0>; + reg = <0x100000 0x3000>; + interrupts = <82 83>; + op-mode = <0>; /* MCASP_IIS_MODE */ + tdm-slots = <2>; + num-serializer = <16>; + serial-dir = < + 0 0 0 0 /* 0: INACTIVE, 1: TX, 2: RX */ + 0 0 0 0 + 0 0 0 1 + 2 0 0 0 >; + tx-num-evt = <1>; + rx-num-evt = <1>; +}; diff --git a/Documentation/devicetree/bindings/sound/omap-abe-twl6040.txt b/Documentation/devicetree/bindings/sound/omap-abe-twl6040.txt new file mode 100644 index 000000000000..65dec876cb2d --- /dev/null +++ b/Documentation/devicetree/bindings/sound/omap-abe-twl6040.txt @@ -0,0 +1,91 @@ +* Texas Instruments OMAP4+ and twl6040 based audio setups + +Required properties: +- compatible: "ti,abe-twl6040" +- ti,model: Name of the sound card ( for example "SDP4430") +- ti,mclk-freq: MCLK frequency for HPPLL operation +- ti,mcpdm: phandle for the McPDM node +- ti,twl6040: phandle for the twl6040 core node +- ti,audio-routing: List of connections between audio components. + Each entry is a pair of strings, the first being the connection's sink, + the second being the connection's source. + +Optional properties: +- ti,dmic: phandle for the OMAP dmic node if the machine have it connected +- ti,jack_detection: Need to be set to <1> if the board capable to detect jack + insertion, removal. + +Available audio endpoints for the audio-routing table: + +Board connectors: + * Headset Stereophone + * Earphone Spk + * Ext Spk + * Line Out + * Vibrator + * Headset Mic + * Main Handset Mic + * Sub Handset Mic + * Line In + * Digital Mic + +twl6040 pins: + * HSOL + * HSOR + * EP + * HFL + * HFR + * AUXL + * AUXR + * VIBRAL + * VIBRAR + * HSMIC + * MAINMIC + * SUBMIC + * AFML + * AFMR + + * Headset Mic Bias + * Main Mic Bias + * Digital Mic1 Bias + * Digital Mic2 Bias + +Digital mic pins: + * DMic + +Example: + +sound { + compatible = "ti,abe-twl6040"; + ti,model = "SDP4430"; + + ti,jack-detection = <1>; + ti,mclk-freq = <38400000>; + + ti,mcpdm = <&mcpdm>; + ti,dmic = <&dmic>; + + ti,twl6040 = <&twl6040>; + + /* Audio routing */ + ti,audio-routing = + "Headset Stereophone", "HSOL", + "Headset Stereophone", "HSOR", + "Earphone Spk", "EP", + "Ext Spk", "HFL", + "Ext Spk", "HFR", + "Line Out", "AUXL", + "Line Out", "AUXR", + "Vibrator", "VIBRAL", + "Vibrator", "VIBRAR", + "HSMIC", "Headset Mic", + "Headset Mic", "Headset Mic Bias", + "MAINMIC", "Main Handset Mic", + "Main Handset Mic", "Main Mic Bias", + "SUBMIC", "Sub Handset Mic", + "Sub Handset Mic", "Main Mic Bias", + "AFML", "Line In", + "AFMR", "Line In", + "DMic", "Digital Mic", + "Digital Mic", "Digital Mic1 Bias"; +}; diff --git a/Documentation/devicetree/bindings/sound/omap-mcbsp.txt b/Documentation/devicetree/bindings/sound/omap-mcbsp.txt new file mode 100644 index 000000000000..17cce4490456 --- /dev/null +++ b/Documentation/devicetree/bindings/sound/omap-mcbsp.txt @@ -0,0 +1,37 @@ +* Texas Instruments OMAP2+ McBSP module + +Required properties: +- compatible: "ti,omap2420-mcbsp" for McBSP on OMAP2420 + "ti,omap2430-mcbsp" for McBSP on OMAP2430 + "ti,omap3-mcbsp" for McBSP on OMAP3 + "ti,omap4-mcbsp" for McBSP on OMAP4 and newer SoC +- reg: Register location and size, for OMAP4+ as an array: + <MPU access base address, size>, + <L3 interconnect address, size>; +- reg-names: Array of strings associated with the address space +- interrupts: Interrupt numbers for the McBSP port, as an array in case the + McBSP IP have more interrupt lines: + <OCP compliant irq>, + <TX irq>, + <RX irq>; +- interrupt-names: Array of strings associated with the interrupt numbers +- interrupt-parent: The parent interrupt controller +- ti,buffer-size: Size of the FIFO on the port (OMAP2430 and newer SoC) +- ti,hwmods: Name of the hwmod associated to the McBSP port + +Example: + +mcbsp2: mcbsp@49022000 { + compatible = "ti,omap3-mcbsp"; + reg = <0x49022000 0xff>, + <0x49028000 0xff>; + reg-names = "mpu", "sidetone"; + interrupts = <0 17 0x4>, /* OCP compliant interrupt */ + <0 62 0x4>, /* TX interrupt */ + <0 63 0x4>, /* RX interrupt */ + <0 4 0x4>; /* Sidetone */ + interrupt-names = "common", "tx", "rx", "sidetone"; + interrupt-parent = <&intc>; + ti,buffer-size = <1280>; + ti,hwmods = "mcbsp2"; +}; diff --git a/Documentation/devicetree/bindings/sound/omap-twl4030.txt b/Documentation/devicetree/bindings/sound/omap-twl4030.txt new file mode 100644 index 000000000000..6fae51c7f766 --- /dev/null +++ b/Documentation/devicetree/bindings/sound/omap-twl4030.txt @@ -0,0 +1,17 @@ +* Texas Instruments SoC with twl4030 based audio setups + +Required properties: +- compatible: "ti,omap-twl4030" +- ti,model: Name of the sound card (for example "omap3beagle") +- ti,mcbsp: phandle for the McBSP node +- ti,codec: phandle for the twl4030 audio node + +Example: + +sound { + compatible = "ti,omap-twl4030"; + ti,model = "omap3beagle"; + + ti,mcbsp = <&mcbsp2>; + ti,codec = <&twl_audio>; +}; diff --git a/Documentation/devicetree/bindings/sound/tlv320aic3x.txt b/Documentation/devicetree/bindings/sound/tlv320aic3x.txt new file mode 100644 index 000000000000..e7b98f41fa5f --- /dev/null +++ b/Documentation/devicetree/bindings/sound/tlv320aic3x.txt @@ -0,0 +1,20 @@ +Texas Instruments - tlv320aic3x Codec module + +The tlv320aic3x serial control bus communicates through I2C protocols + +Required properties: +- compatible - "string" - "ti,tlv320aic3x" +- reg - <int> - I2C slave address + + +Optional properties: + +- gpio-reset - gpio pin number used for codec reset +- ai3x-gpio-func - <array of 2 int> - AIC3X_GPIO1 & AIC3X_GPIO2 Functionality + +Example: + +tlv320aic3x: tlv320aic3x@1b { + compatible = "ti,tlv320aic3x"; + reg = <0x1b>; +}; diff --git a/Documentation/devicetree/bindings/spi/spi-octeon.txt b/Documentation/devicetree/bindings/spi/spi-octeon.txt new file mode 100644 index 000000000000..431add192342 --- /dev/null +++ b/Documentation/devicetree/bindings/spi/spi-octeon.txt @@ -0,0 +1,33 @@ +Cavium, Inc. OCTEON SOC SPI master controller. + +Required properties: +- compatible : "cavium,octeon-3010-spi" +- reg : The register base for the controller. +- interrupts : One interrupt, used by the controller. +- #address-cells : <1>, as required by generic SPI binding. +- #size-cells : <0>, also as required by generic SPI binding. + +Child nodes as per the generic SPI binding. + +Example: + + spi@1070000001000 { + compatible = "cavium,octeon-3010-spi"; + reg = <0x10700 0x00001000 0x0 0x100>; + interrupts = <0 58>; + #address-cells = <1>; + #size-cells = <0>; + + eeprom@0 { + compatible = "st,m95256", "atmel,at25"; + reg = <0>; + spi-max-frequency = <5000000>; + spi-cpha; + spi-cpol; + + pagesize = <64>; + size = <32768>; + address-width = <16>; + }; + }; + diff --git a/Documentation/devicetree/bindings/timer/brcm,bcm2835-system-timer.txt b/Documentation/devicetree/bindings/timer/brcm,bcm2835-system-timer.txt index 2de21c2acf55..844bd5fbd04c 100644 --- a/Documentation/devicetree/bindings/timer/brcm,bcm2835-system-timer.txt +++ b/Documentation/devicetree/bindings/timer/brcm,bcm2835-system-timer.txt @@ -7,7 +7,7 @@ free running counter values, and generates an interrupt. Required properties: -- compatible : should be "brcm,bcm2835-system-timer.txt" +- compatible : should be "brcm,bcm2835-system-timer" - reg : Specifies base physical address and size of the registers. - interrupts : A list of 4 interrupt sinks; one per timer channel. - clock-frequency : The frequency of the clock that drives the counter, in Hz. diff --git a/Documentation/devicetree/bindings/video/backlight/88pm860x.txt b/Documentation/devicetree/bindings/video/backlight/88pm860x.txt new file mode 100644 index 000000000000..261df2799315 --- /dev/null +++ b/Documentation/devicetree/bindings/video/backlight/88pm860x.txt @@ -0,0 +1,15 @@ +88pm860x-backlight bindings + +Optional properties: + - marvell,88pm860x-iset: Current supplies on backlight device. + - marvell,88pm860x-pwm: PWM frequency on backlight device. + +Example: + + backlights { + backlight-0 { + marvell,88pm860x-iset = <4>; + marvell,88pm860x-pwm = <3>; + }; + backlight-2 { + }; |