diff options
Diffstat (limited to 'Documentation/devicetree/bindings')
4 files changed, 174 insertions, 8 deletions
diff --git a/Documentation/devicetree/bindings/media/i2c/adv7604.txt b/Documentation/devicetree/bindings/media/i2c/adv7604.txt index c27cede3bd68..8337f75c75da 100644 --- a/Documentation/devicetree/bindings/media/i2c/adv7604.txt +++ b/Documentation/devicetree/bindings/media/i2c/adv7604.txt @@ -1,15 +1,17 @@ -* Analog Devices ADV7604/11 video decoder with HDMI receiver +* Analog Devices ADV7604/11/12 video decoder with HDMI receiver -The ADV7604 and ADV7611 are multiformat video decoders with an integrated HDMI -receiver. The ADV7604 has four multiplexed HDMI inputs and one analog input, -and the ADV7611 has one HDMI input and no analog input. +The ADV7604 and ADV7611/12 are multiformat video decoders with an integrated +HDMI receiver. The ADV7604 has four multiplexed HDMI inputs and one analog +input, and the ADV7611 has one HDMI input and no analog input. The 7612 is +similar to the 7611 but has 2 HDMI inputs. -These device tree bindings support the ADV7611 only at the moment. +These device tree bindings support the ADV7611/12 only at the moment. Required Properties: - compatible: Must contain one of the following - "adi,adv7611" for the ADV7611 + - "adi,adv7612" for the ADV7612 - reg: I2C slave address @@ -22,10 +24,10 @@ port, in accordance with the video interface bindings defined in Documentation/devicetree/bindings/media/video-interfaces.txt. The port nodes are numbered as follows. - Port ADV7611 + Port ADV7611 ADV7612 ------------------------------------------------------------ - HDMI 0 - Digital output 1 + HDMI 0 0, 1 + Digital output 1 2 The digital output port node must contain at least one endpoint. @@ -45,6 +47,7 @@ Optional Endpoint Properties: If none of hsync-active, vsync-active and pclk-sample is specified the endpoint will use embedded BT.656 synchronization. + - default-input: Select which input is selected after reset. Example: @@ -58,6 +61,8 @@ Example: #address-cells = <1>; #size-cells = <0>; + default-input = <0>; + port@0 { reg = <0>; }; diff --git a/Documentation/devicetree/bindings/media/i2c/tc358743.txt b/Documentation/devicetree/bindings/media/i2c/tc358743.txt new file mode 100644 index 000000000000..5218921629ed --- /dev/null +++ b/Documentation/devicetree/bindings/media/i2c/tc358743.txt @@ -0,0 +1,48 @@ +* Toshiba TC358743 HDMI-RX to MIPI CSI2-TX Bridge + +The Toshiba TC358743 HDMI-RX to MIPI CSI2-TX (H2C) is a bridge that converts +a HDMI stream to MIPI CSI-2 TX. It is programmable through I2C. + +Required Properties: + +- compatible: value should be "toshiba,tc358743" +- clocks, clock-names: should contain a phandle link to the reference clock + source, the clock input is named "refclk". + +Optional Properties: + +- reset-gpios: gpio phandle GPIO connected to the reset pin +- interrupts, interrupt-parent: GPIO connected to the interrupt pin +- data-lanes: should be <1 2 3 4> for four-lane operation, + or <1 2> for two-lane operation +- clock-lanes: should be <0> +- clock-noncontinuous: Presence of this boolean property decides whether the + MIPI CSI-2 clock is continuous or non-continuous. +- link-frequencies: List of allowed link frequencies in Hz. Each frequency is + expressed as a 64-bit big-endian integer. The frequency + is half of the bps per lane due to DDR transmission. + +For further information on the MIPI CSI-2 endpoint node properties, see +Documentation/devicetree/bindings/media/video-interfaces.txt. + +Example: + + tc358743@0f { + compatible = "toshiba,tc358743"; + reg = <0x0f>; + clocks = <&hdmi_osc>; + clock-names = "refclk"; + reset-gpios = <&gpio6 9 GPIO_ACTIVE_LOW>; + interrupt-parent = <&gpio2>; + interrupts = <5 IRQ_TYPE_LEVEL_HIGH>; + + port { + tc358743_out: endpoint { + remote-endpoint = <&mipi_csi2_in>; + data-lanes = <1 2 3 4>; + clock-lanes = <0>; + clock-noncontinuous; + link-frequencies = /bits/ 64 <297000000>; + }; + }; + }; diff --git a/Documentation/devicetree/bindings/media/renesas,jpu.txt b/Documentation/devicetree/bindings/media/renesas,jpu.txt new file mode 100644 index 000000000000..0cb94201bf92 --- /dev/null +++ b/Documentation/devicetree/bindings/media/renesas,jpu.txt @@ -0,0 +1,24 @@ +* Renesas JPEG Processing Unit + +The JPEG processing unit (JPU) incorporates the JPEG codec with an encoding +and decoding function conforming to the JPEG baseline process, so that the JPU +can encode image data and decode JPEG data quickly. + +Required properties: + - compatible: should containg one of the following: + - "renesas,jpu-r8a7790" for R-Car H2 + - "renesas,jpu-r8a7791" for R-Car M2-W + - "renesas,jpu-r8a7792" for R-Car V2H + - "renesas,jpu-r8a7793" for R-Car M2-N + + - reg: Base address and length of the registers block for the JPU. + - interrupts: JPU interrupt specifier. + - clocks: A phandle + clock-specifier pair for the JPU functional clock. + +Example: R8A7790 (R-Car H2) JPU node + jpeg-codec@fe980000 { + compatible = "renesas,jpu-r8a7790"; + reg = <0 0xfe980000 0 0x10300>; + interrupts = <0 272 IRQ_TYPE_LEVEL_HIGH>; + clocks = <&mstp1_clks R8A7790_CLK_JPU>; + }; diff --git a/Documentation/devicetree/bindings/media/stih407-c8sectpfe.txt b/Documentation/devicetree/bindings/media/stih407-c8sectpfe.txt new file mode 100644 index 000000000000..d4def767bdfe --- /dev/null +++ b/Documentation/devicetree/bindings/media/stih407-c8sectpfe.txt @@ -0,0 +1,89 @@ +STMicroelectronics STi c8sectpfe binding +============================================ + +This document describes the c8sectpfe device bindings that is used to get transport +stream data into the SoC on the TS pins, and into DDR for further processing. + +It is typically used in conjunction with one or more demodulator and tuner devices +which converts from the RF to digital domain. Demodulators and tuners are usually +located on an external DVB frontend card connected to SoC TS input pins. + +Currently 7 TS input (tsin) channels are supported on the stih407 family SoC. + +Required properties (controller (parent) node): +- compatible : Should be "stih407-c8sectpfe" + +- reg : Address and length of register sets for each device in + "reg-names" + +- reg-names : The names of the register addresses corresponding to the + registers filled in "reg": + - c8sectpfe: c8sectpfe registers + - c8sectpfe-ram: c8sectpfe internal sram + +- clocks : phandle list of c8sectpfe clocks +- clock-names : should be "c8sectpfe" +See: Documentation/devicetree/bindings/clock/clock-bindings.txt + +- pinctrl-names : a pinctrl state named tsin%d-serial or tsin%d-parallel (where %d is tsin-num) + must be defined for each tsin child node. +- pinctrl-0 : phandle referencing pin configuration for this tsin configuration +See: Documentation/devicetree/bindings/pinctrl/pinctrl-binding.txt + + +Required properties (tsin (child) node): + +- tsin-num : tsin id of the InputBlock (must be between 0 to 6) +- i2c-bus : phandle to the I2C bus DT node which the demodulators & tuners on this tsin channel are connected. +- rst-gpio : reset gpio for this tsin channel. + +Optional properties (tsin (child) node): + +- invert-ts-clk : Bool property to control sense of ts input clock (data stored on falling edge of clk). +- serial-not-parallel : Bool property to configure input bus width (serial on ts_data<7>). +- async-not-sync : Bool property to control if data is received in asynchronous mode + (all bits/bytes with ts_valid or ts_packet asserted are valid). + +- dvb-card : Describes the NIM card connected to this tsin channel. + +Example: + +/* stih410 SoC b2120 + b2004a + stv0367-pll(NIMB) + stv0367-tda18212 (NIMA) DT example) */ + + c8sectpfe@08a20000 { + compatible = "st,stih407-c8sectpfe"; + status = "okay"; + reg = <0x08a20000 0x10000>, <0x08a00000 0x4000>; + reg-names = "stfe", "stfe-ram"; + interrupts = <0 34 0>, <0 35 0>; + interrupt-names = "stfe-error-irq", "stfe-idle-irq"; + + pinctrl-names = "tsin0-serial", "tsin0-parallel", "tsin3-serial", + "tsin4-serial", "tsin5-serial"; + + pinctrl-0 = <&pinctrl_tsin0_serial>; + pinctrl-1 = <&pinctrl_tsin0_parallel>; + pinctrl-2 = <&pinctrl_tsin3_serial>; + pinctrl-3 = <&pinctrl_tsin4_serial_alt3>; + pinctrl-4 = <&pinctrl_tsin5_serial_alt1>; + + clocks = <&clk_s_c0_flexgen CLK_PROC_STFE>; + clock-names = "stfe"; + + /* tsin0 is TSA on NIMA */ + tsin0: port@0 { + tsin-num = <0>; + serial-not-parallel; + i2c-bus = <&ssc2>; + rst-gpio = <&pio15 4 0>; + dvb-card = <STV0367_TDA18212_NIMA_1>; + }; + + tsin3: port@3 { + tsin-num = <3>; + serial-not-parallel; + i2c-bus = <&ssc3>; + rst-gpio = <&pio15 7 0>; + dvb-card = <STV0367_TDA18212_NIMB_1>; + }; + }; |