diff options
Diffstat (limited to 'Documentation/devicetree/bindings/mtd/qcom_nandc.txt')
| -rw-r--r-- | Documentation/devicetree/bindings/mtd/qcom_nandc.txt | 142 |
1 files changed, 0 insertions, 142 deletions
diff --git a/Documentation/devicetree/bindings/mtd/qcom_nandc.txt b/Documentation/devicetree/bindings/mtd/qcom_nandc.txt deleted file mode 100644 index 5647913d8837..000000000000 --- a/Documentation/devicetree/bindings/mtd/qcom_nandc.txt +++ /dev/null @@ -1,142 +0,0 @@ -* Qualcomm NAND controller - -Required properties: -- compatible: must be one of the following: - * "qcom,ipq806x-nand" - for EBI2 NAND controller being used in IPQ806x - SoC and it uses ADM DMA - * "qcom,ipq4019-nand" - for QPIC NAND controller v1.4.0 being used in - IPQ4019 SoC and it uses BAM DMA - * "qcom,ipq6018-nand" - for QPIC NAND controller v1.5.0 being used in - IPQ6018 SoC and it uses BAM DMA - * "qcom,ipq8074-nand" - for QPIC NAND controller v1.5.0 being used in - IPQ8074 SoC and it uses BAM DMA - * "qcom,sdx55-nand" - for QPIC NAND controller v2.0.0 being used in - SDX55 SoC and it uses BAM DMA - -- reg: MMIO address range -- clocks: must contain core clock and always on clock -- clock-names: must contain "core" for the core clock and "aon" for the - always on clock - -EBI2 specific properties: -- dmas: DMA specifier, consisting of a phandle to the ADM DMA - controller node and the channel number to be used for - NAND. Refer to dma.txt and qcom_adm.txt for more details -- dma-names: must be "rxtx" -- qcom,cmd-crci: must contain the ADM command type CRCI block instance - number specified for the NAND controller on the given - platform -- qcom,data-crci: must contain the ADM data type CRCI block instance - number specified for the NAND controller on the given - platform - -QPIC specific properties: -- dmas: DMA specifier, consisting of a phandle to the BAM DMA - and the channel number to be used for NAND. Refer to - dma.txt, qcom_bam_dma.txt for more details -- dma-names: must contain all 3 channel names : "tx", "rx", "cmd" -- #address-cells: <1> - subnodes give the chip-select number -- #size-cells: <0> - -* NAND chip-select - -Each controller may contain one or more subnodes to represent enabled -chip-selects which (may) contain NAND flash chips. Their properties are as -follows. - -Required properties: -- reg: a single integer representing the chip-select - number (e.g., 0, 1, 2, etc.) -- #address-cells: see partition.txt -- #size-cells: see partition.txt - -Optional properties: -- nand-bus-width: see nand-controller.yaml -- nand-ecc-strength: see nand-controller.yaml. If not specified, then ECC strength will - be used according to chip requirement and available - OOB size. - -Each nandcs device node may optionally contain a 'partitions' sub-node, which -further contains sub-nodes describing the flash partition mapping. See -partition.txt for more detail. - -Example: - -nand-controller@1ac00000 { - compatible = "qcom,ipq806x-nand"; - reg = <0x1ac00000 0x800>; - - clocks = <&gcc EBI2_CLK>, - <&gcc EBI2_AON_CLK>; - clock-names = "core", "aon"; - - dmas = <&adm_dma 3>; - dma-names = "rxtx"; - qcom,cmd-crci = <15>; - qcom,data-crci = <3>; - - #address-cells = <1>; - #size-cells = <0>; - - nand@0 { - reg = <0>; - - nand-ecc-strength = <4>; - nand-bus-width = <8>; - - partitions { - compatible = "fixed-partitions"; - #address-cells = <1>; - #size-cells = <1>; - - partition@0 { - label = "boot-nand"; - reg = <0 0x58a0000>; - }; - - partition@58a0000 { - label = "fs-nand"; - reg = <0x58a0000 0x4000000>; - }; - }; - }; -}; - -nand-controller@79b0000 { - compatible = "qcom,ipq4019-nand"; - reg = <0x79b0000 0x1000>; - - clocks = <&gcc GCC_QPIC_CLK>, - <&gcc GCC_QPIC_AHB_CLK>; - clock-names = "core", "aon"; - - dmas = <&qpicbam 0>, - <&qpicbam 1>, - <&qpicbam 2>; - dma-names = "tx", "rx", "cmd"; - - #address-cells = <1>; - #size-cells = <0>; - - nand@0 { - reg = <0>; - nand-ecc-strength = <4>; - nand-bus-width = <8>; - - partitions { - compatible = "fixed-partitions"; - #address-cells = <1>; - #size-cells = <1>; - - partition@0 { - label = "boot-nand"; - reg = <0 0x58a0000>; - }; - - partition@58a0000 { - label = "fs-nand"; - reg = <0x58a0000 0x4000000>; - }; - }; - }; -}; |