diff options
Diffstat (limited to 'Documentation/devicetree/bindings/clock')
23 files changed, 670 insertions, 657 deletions
diff --git a/Documentation/devicetree/bindings/clock/altr_socfpga.txt b/Documentation/devicetree/bindings/clock/altr_socfpga.txt index 0045433eae1f..5dfd145d3ccf 100644 --- a/Documentation/devicetree/bindings/clock/altr_socfpga.txt +++ b/Documentation/devicetree/bindings/clock/altr_socfpga.txt @@ -23,3 +23,8 @@ Optional properties: and the bit index. - div-reg : For "socfpga-gate-clk", div-reg contains the divider register, bit shift, and width. +- clk-phase : For the sdmmc_clk, contains the value of the clock phase that controls + the SDMMC CIU clock. The first value is the clk_sample(smpsel), and the second + value is the cclk_in_drv(drvsel). The clk-phase is used to enable the correct + hold/delay times that is needed for the SD/MMC CIU clock. The values of both + can be 0-315 degrees, in 45 degree increments. diff --git a/Documentation/devicetree/bindings/clock/arm-integrator.txt b/Documentation/devicetree/bindings/clock/arm-integrator.txt new file mode 100644 index 000000000000..652914b17b95 --- /dev/null +++ b/Documentation/devicetree/bindings/clock/arm-integrator.txt @@ -0,0 +1,34 @@ +Clock bindings for ARM Integrator Core Module clocks + +Auxilary Oscillator Clock + +This is a configurable clock fed from a 24 MHz chrystal, +used for generating e.g. video clocks. It is located on the +core module and there is only one of these. + +This clock node *must* be a subnode of the core module, since +it obtains the base address for it's address range from its +parent node. + + +Required properties: +- compatible: must be "arm,integrator-cm-auxosc" +- #clock-cells: must be <0> + +Optional properties: +- clocks: parent clock(s) + +Example: + +core-module@10000000 { + xtal24mhz: xtal24mhz@24M { + #clock-cells = <0>; + compatible = "fixed-clock"; + clock-frequency = <24000000>; + }; + auxosc: cm_aux_osc@25M { + #clock-cells = <0>; + compatible = "arm,integrator-cm-auxosc"; + clocks = <&xtal24mhz>; + }; +}; diff --git a/Documentation/devicetree/bindings/clock/axi-clkgen.txt b/Documentation/devicetree/bindings/clock/axi-clkgen.txt index 028b493e97ff..20e1704e7df2 100644 --- a/Documentation/devicetree/bindings/clock/axi-clkgen.txt +++ b/Documentation/devicetree/bindings/clock/axi-clkgen.txt @@ -5,7 +5,7 @@ This binding uses the common clock binding[1]. [1] Documentation/devicetree/bindings/clock/clock-bindings.txt Required properties: -- compatible : shall be "adi,axi-clkgen". +- compatible : shall be "adi,axi-clkgen-1.00.a" or "adi,axi-clkgen-2.00.a". - #clock-cells : from common clock binding; Should always be set to 0. - reg : Address and length of the axi-clkgen register set. - clocks : Phandle and clock specifier for the parent clock. diff --git a/Documentation/devicetree/bindings/clock/clock-bindings.txt b/Documentation/devicetree/bindings/clock/clock-bindings.txt index 7c52c29d99fa..700e7aac3717 100644 --- a/Documentation/devicetree/bindings/clock/clock-bindings.txt +++ b/Documentation/devicetree/bindings/clock/clock-bindings.txt @@ -44,6 +44,23 @@ For example: clocks by index. The names should reflect the clock output signal names for the device. +clock-indices: If the identifyng number for the clocks in the node + is not linear from zero, then the this mapping allows + the mapping of identifiers into the clock-output-names + array. + +For example, if we have two clocks <&oscillator 1> and <&oscillator 3>: + + oscillator { + compatible = "myclocktype"; + #clock-cells = <1>; + clock-indices = <1>, <3>; + clock-output-names = "clka", "clkb"; + } + + This ensures we do not have any empty nodes in clock-output-names + + ==Clock consumers== Required properties: diff --git a/Documentation/devicetree/bindings/clock/exynos4-clock.txt b/Documentation/devicetree/bindings/clock/exynos4-clock.txt index a2ac2d9ac71a..f5a5b19ed3b2 100644 --- a/Documentation/devicetree/bindings/clock/exynos4-clock.txt +++ b/Documentation/devicetree/bindings/clock/exynos4-clock.txt @@ -15,259 +15,12 @@ Required Properties: - #clock-cells: should be 1. -The following is the list of clocks generated by the controller. Each clock is -assigned an identifier and client nodes use this identifier to specify the -clock which they consume. Some of the clocks are available only on a particular -Exynos4 SoC and this is specified where applicable. - - - [Core Clocks] - - Clock ID SoC (if specific) - ----------------------------------------------- - - xxti 1 - xusbxti 2 - fin_pll 3 - fout_apll 4 - fout_mpll 5 - fout_epll 6 - fout_vpll 7 - sclk_apll 8 - sclk_mpll 9 - sclk_epll 10 - sclk_vpll 11 - arm_clk 12 - aclk200 13 - aclk100 14 - aclk160 15 - aclk133 16 - mout_mpll_user_t 17 Exynos4x12 - mout_mpll_user_c 18 Exynos4x12 - mout_core 19 - mout_apll 20 - - - [Clock Gate for Special Clocks] - - Clock ID SoC (if specific) - ----------------------------------------------- - - sclk_fimc0 128 - sclk_fimc1 129 - sclk_fimc2 130 - sclk_fimc3 131 - sclk_cam0 132 - sclk_cam1 133 - sclk_csis0 134 - sclk_csis1 135 - sclk_hdmi 136 - sclk_mixer 137 - sclk_dac 138 - sclk_pixel 139 - sclk_fimd0 140 - sclk_mdnie0 141 Exynos4412 - sclk_mdnie_pwm0 12 142 Exynos4412 - sclk_mipi0 143 - sclk_audio0 144 - sclk_mmc0 145 - sclk_mmc1 146 - sclk_mmc2 147 - sclk_mmc3 148 - sclk_mmc4 149 - sclk_sata 150 Exynos4210 - sclk_uart0 151 - sclk_uart1 152 - sclk_uart2 153 - sclk_uart3 154 - sclk_uart4 155 - sclk_audio1 156 - sclk_audio2 157 - sclk_spdif 158 - sclk_spi0 159 - sclk_spi1 160 - sclk_spi2 161 - sclk_slimbus 162 - sclk_fimd1 163 Exynos4210 - sclk_mipi1 164 Exynos4210 - sclk_pcm1 165 - sclk_pcm2 166 - sclk_i2s1 167 - sclk_i2s2 168 - sclk_mipihsi 169 Exynos4412 - sclk_mfc 170 - sclk_pcm0 171 - sclk_g3d 172 - sclk_pwm_isp 173 Exynos4x12 - sclk_spi0_isp 174 Exynos4x12 - sclk_spi1_isp 175 Exynos4x12 - sclk_uart_isp 176 Exynos4x12 - sclk_fimg2d 177 - - [Peripheral Clock Gates] - - Clock ID SoC (if specific) - ----------------------------------------------- - - fimc0 256 - fimc1 257 - fimc2 258 - fimc3 259 - csis0 260 - csis1 261 - jpeg 262 - smmu_fimc0 263 - smmu_fimc1 264 - smmu_fimc2 265 - smmu_fimc3 266 - smmu_jpeg 267 - vp 268 - mixer 269 - tvenc 270 Exynos4210 - hdmi 271 - smmu_tv 272 - mfc 273 - smmu_mfcl 274 - smmu_mfcr 275 - g3d 276 - g2d 277 - rotator 278 Exynos4210 - mdma 279 Exynos4210 - smmu_g2d 280 Exynos4210 - smmu_rotator 281 Exynos4210 - smmu_mdma 282 Exynos4210 - fimd0 283 - mie0 284 - mdnie0 285 Exynos4412 - dsim0 286 - smmu_fimd0 287 - fimd1 288 Exynos4210 - mie1 289 Exynos4210 - dsim1 290 Exynos4210 - smmu_fimd1 291 Exynos4210 - pdma0 292 - pdma1 293 - pcie_phy 294 - sata_phy 295 Exynos4210 - tsi 296 - sdmmc0 297 - sdmmc1 298 - sdmmc2 299 - sdmmc3 300 - sdmmc4 301 - sata 302 Exynos4210 - sromc 303 - usb_host 304 - usb_device 305 - pcie 306 - onenand 307 - nfcon 308 - smmu_pcie 309 - gps 310 - smmu_gps 311 - uart0 312 - uart1 313 - uart2 314 - uart3 315 - uart4 316 - i2c0 317 - i2c1 318 - i2c2 319 - i2c3 320 - i2c4 321 - i2c5 322 - i2c6 323 - i2c7 324 - i2c_hdmi 325 - tsadc 326 - spi0 327 - spi1 328 - spi2 329 - i2s1 330 - i2s2 331 - pcm0 332 - i2s0 333 - pcm1 334 - pcm2 335 - pwm 336 - slimbus 337 - spdif 338 - ac97 339 - modemif 340 - chipid 341 - sysreg 342 - hdmi_cec 343 - mct 344 - wdt 345 - rtc 346 - keyif 347 - audss 348 - mipi_hsi 349 Exynos4210 - mdma2 350 Exynos4210 - pixelasyncm0 351 - pixelasyncm1 352 - fimc_lite0 353 Exynos4x12 - fimc_lite1 354 Exynos4x12 - ppmuispx 355 Exynos4x12 - ppmuispmx 356 Exynos4x12 - fimc_isp 357 Exynos4x12 - fimc_drc 358 Exynos4x12 - fimc_fd 359 Exynos4x12 - mcuisp 360 Exynos4x12 - gicisp 361 Exynos4x12 - smmu_isp 362 Exynos4x12 - smmu_drc 363 Exynos4x12 - smmu_fd 364 Exynos4x12 - smmu_lite0 365 Exynos4x12 - smmu_lite1 366 Exynos4x12 - mcuctl_isp 367 Exynos4x12 - mpwm_isp 368 Exynos4x12 - i2c0_isp 369 Exynos4x12 - i2c1_isp 370 Exynos4x12 - mtcadc_isp 371 Exynos4x12 - pwm_isp 372 Exynos4x12 - wdt_isp 373 Exynos4x12 - uart_isp 374 Exynos4x12 - asyncaxim 375 Exynos4x12 - smmu_ispcx 376 Exynos4x12 - spi0_isp 377 Exynos4x12 - spi1_isp 378 Exynos4x12 - pwm_isp_sclk 379 Exynos4x12 - spi0_isp_sclk 380 Exynos4x12 - spi1_isp_sclk 381 Exynos4x12 - uart_isp_sclk 382 Exynos4x12 - tmu_apbif 383 - - [Mux Clocks] - - Clock ID SoC (if specific) - ----------------------------------------------- - - mout_fimc0 384 - mout_fimc1 385 - mout_fimc2 386 - mout_fimc3 387 - mout_cam0 388 - mout_cam1 389 - mout_csis0 390 - mout_csis1 391 - mout_g3d0 392 - mout_g3d1 393 - mout_g3d 394 - aclk400_mcuisp 395 Exynos4x12 - - [Div Clocks] - - Clock ID SoC (if specific) - ----------------------------------------------- - - div_isp0 450 Exynos4x12 - div_isp1 451 Exynos4x12 - div_mcuisp0 452 Exynos4x12 - div_mcuisp1 453 Exynos4x12 - div_aclk200 454 Exynos4x12 - div_aclk400_mcuisp 455 Exynos4x12 +Each clock is assigned an identifier and client nodes can use this identifier +to specify the clock which they consume. +All available clocks are defined as preprocessor macros in +dt-bindings/clock/exynos4.h header and can be used in device +tree sources. Example 1: An example of a clock controller node is listed below. @@ -285,6 +38,6 @@ Example 2: UART controller node that consumes the clock generated by the clock compatible = "samsung,exynos4210-uart"; reg = <0x13820000 0x100>; interrupts = <0 54 0>; - clocks = <&clock 314>, <&clock 153>; + clocks = <&clock CLK_UART2>, <&clock CLK_SCLK_UART2>; clock-names = "uart", "clk_uart_baud0"; }; diff --git a/Documentation/devicetree/bindings/clock/exynos5250-clock.txt b/Documentation/devicetree/bindings/clock/exynos5250-clock.txt index 72ce617dea82..536eacd1063f 100644 --- a/Documentation/devicetree/bindings/clock/exynos5250-clock.txt +++ b/Documentation/devicetree/bindings/clock/exynos5250-clock.txt @@ -13,163 +13,12 @@ Required Properties: - #clock-cells: should be 1. -The following is the list of clocks generated by the controller. Each clock is -assigned an identifier and client nodes use this identifier to specify the -clock which they consume. - - - [Core Clocks] - - Clock ID - ---------------------------- - - fin_pll 1 - - [Clock Gate for Special Clocks] - - Clock ID - ---------------------------- - - sclk_cam_bayer 128 - sclk_cam0 129 - sclk_cam1 130 - sclk_gscl_wa 131 - sclk_gscl_wb 132 - sclk_fimd1 133 - sclk_mipi1 134 - sclk_dp 135 - sclk_hdmi 136 - sclk_pixel 137 - sclk_audio0 138 - sclk_mmc0 139 - sclk_mmc1 140 - sclk_mmc2 141 - sclk_mmc3 142 - sclk_sata 143 - sclk_usb3 144 - sclk_jpeg 145 - sclk_uart0 146 - sclk_uart1 147 - sclk_uart2 148 - sclk_uart3 149 - sclk_pwm 150 - sclk_audio1 151 - sclk_audio2 152 - sclk_spdif 153 - sclk_spi0 154 - sclk_spi1 155 - sclk_spi2 156 - div_i2s1 157 - div_i2s2 158 - sclk_hdmiphy 159 - div_pcm0 160 - - - [Peripheral Clock Gates] - - Clock ID - ---------------------------- - - gscl0 256 - gscl1 257 - gscl2 258 - gscl3 259 - gscl_wa 260 - gscl_wb 261 - smmu_gscl0 262 - smmu_gscl1 263 - smmu_gscl2 264 - smmu_gscl3 265 - mfc 266 - smmu_mfcl 267 - smmu_mfcr 268 - rotator 269 - jpeg 270 - mdma1 271 - smmu_rotator 272 - smmu_jpeg 273 - smmu_mdma1 274 - pdma0 275 - pdma1 276 - sata 277 - usbotg 278 - mipi_hsi 279 - sdmmc0 280 - sdmmc1 281 - sdmmc2 282 - sdmmc3 283 - sromc 284 - usb2 285 - usb3 286 - sata_phyctrl 287 - sata_phyi2c 288 - uart0 289 - uart1 290 - uart2 291 - uart3 292 - uart4 293 - i2c0 294 - i2c1 295 - i2c2 296 - i2c3 297 - i2c4 298 - i2c5 299 - i2c6 300 - i2c7 301 - i2c_hdmi 302 - adc 303 - spi0 304 - spi1 305 - spi2 306 - i2s1 307 - i2s2 308 - pcm1 309 - pcm2 310 - pwm 311 - spdif 312 - ac97 313 - hsi2c0 314 - hsi2c1 315 - hs12c2 316 - hs12c3 317 - chipid 318 - sysreg 319 - pmu 320 - cmu_top 321 - cmu_core 322 - cmu_mem 323 - tzpc0 324 - tzpc1 325 - tzpc2 326 - tzpc3 327 - tzpc4 328 - tzpc5 329 - tzpc6 330 - tzpc7 331 - tzpc8 332 - tzpc9 333 - hdmi_cec 334 - mct 335 - wdt 336 - rtc 337 - tmu 338 - fimd1 339 - mie1 340 - dsim0 341 - dp 342 - mixer 343 - hdmi 344 - g2d 345 - mdma0 346 - smmu_mdma0 347 - - - [Clock Muxes] - - Clock ID - ---------------------------- - mout_hdmi 1024 +Each clock is assigned an identifier and client nodes can use this identifier +to specify the clock which they consume. +All available clocks are defined as preprocessor macros in +dt-bindings/clock/exynos5250.h header and can be used in device +tree sources. Example 1: An example of a clock controller node is listed below. @@ -187,6 +36,6 @@ Example 2: UART controller node that consumes the clock generated by the clock compatible = "samsung,exynos4210-uart"; reg = <0x13820000 0x100>; interrupts = <0 54 0>; - clocks = <&clock 314>, <&clock 153>; + clocks = <&clock CLK_UART2>, <&clock CLK_SCLK_UART2>; clock-names = "uart", "clk_uart_baud0"; }; diff --git a/Documentation/devicetree/bindings/clock/exynos5420-clock.txt b/Documentation/devicetree/bindings/clock/exynos5420-clock.txt index 458f34789e5d..ca88c97a8562 100644 --- a/Documentation/devicetree/bindings/clock/exynos5420-clock.txt +++ b/Documentation/devicetree/bindings/clock/exynos5420-clock.txt @@ -13,184 +13,12 @@ Required Properties: - #clock-cells: should be 1. -The following is the list of clocks generated by the controller. Each clock is -assigned an identifier and client nodes use this identifier to specify the -clock which they consume. +Each clock is assigned an identifier and client nodes can use this identifier +to specify the clock which they consume. - - [Core Clocks] - - Clock ID - ---------------------------- - - fin_pll 1 - - [Clock Gate for Special Clocks] - - Clock ID - ---------------------------- - sclk_uart0 128 - sclk_uart1 129 - sclk_uart2 130 - sclk_uart3 131 - sclk_mmc0 132 - sclk_mmc1 133 - sclk_mmc2 134 - sclk_spi0 135 - sclk_spi1 136 - sclk_spi2 137 - sclk_i2s1 138 - sclk_i2s2 139 - sclk_pcm1 140 - sclk_pcm2 141 - sclk_spdif 142 - sclk_hdmi 143 - sclk_pixel 144 - sclk_dp1 145 - sclk_mipi1 146 - sclk_fimd1 147 - sclk_maudio0 148 - sclk_maupcm0 149 - sclk_usbd300 150 - sclk_usbd301 151 - sclk_usbphy300 152 - sclk_usbphy301 153 - sclk_unipro 154 - sclk_pwm 155 - sclk_gscl_wa 156 - sclk_gscl_wb 157 - sclk_hdmiphy 158 - - [Peripheral Clock Gates] - - Clock ID - ---------------------------- - - aclk66_peric 256 - uart0 257 - uart1 258 - uart2 259 - uart3 260 - i2c0 261 - i2c1 262 - i2c2 263 - i2c3 264 - i2c4 265 - i2c5 266 - i2c6 267 - i2c7 268 - i2c_hdmi 269 - tsadc 270 - spi0 271 - spi1 272 - spi2 273 - keyif 274 - i2s1 275 - i2s2 276 - pcm1 277 - pcm2 278 - pwm 279 - spdif 280 - i2c8 281 - i2c9 282 - i2c10 283 - aclk66_psgen 300 - chipid 301 - sysreg 302 - tzpc0 303 - tzpc1 304 - tzpc2 305 - tzpc3 306 - tzpc4 307 - tzpc5 308 - tzpc6 309 - tzpc7 310 - tzpc8 311 - tzpc9 312 - hdmi_cec 313 - seckey 314 - mct 315 - wdt 316 - rtc 317 - tmu 318 - tmu_gpu 319 - pclk66_gpio 330 - aclk200_fsys2 350 - mmc0 351 - mmc1 352 - mmc2 353 - sromc 354 - ufs 355 - aclk200_fsys 360 - tsi 361 - pdma0 362 - pdma1 363 - rtic 364 - usbh20 365 - usbd300 366 - usbd301 377 - aclk400_mscl 380 - mscl0 381 - mscl1 382 - mscl2 383 - smmu_mscl0 384 - smmu_mscl1 385 - smmu_mscl2 386 - aclk333 400 - mfc 401 - smmu_mfcl 402 - smmu_mfcr 403 - aclk200_disp1 410 - dsim1 411 - dp1 412 - hdmi 413 - aclk300_disp1 420 - fimd1 421 - smmu_fimd1 422 - aclk166 430 - mixer 431 - aclk266 440 - rotator 441 - mdma1 442 - smmu_rotator 443 - smmu_mdma1 444 - aclk300_jpeg 450 - jpeg 451 - jpeg2 452 - smmu_jpeg 453 - aclk300_gscl 460 - smmu_gscl0 461 - smmu_gscl1 462 - gscl_wa 463 - gscl_wb 464 - gscl0 465 - gscl1 466 - clk_3aa 467 - aclk266_g2d 470 - sss 471 - slim_sss 472 - mdma0 473 - aclk333_g2d 480 - g2d 481 - aclk333_432_gscl 490 - smmu_3aa 491 - smmu_fimcl0 492 - smmu_fimcl1 493 - smmu_fimcl3 494 - fimc_lite3 495 - aclk_g3d 500 - g3d 501 - smmu_mixer 502 - - Mux ID - ---------------------------- - - mout_hdmi 640 - - Divider ID - ---------------------------- - - dout_pixel 768 +All available clocks are defined as preprocessor macros in +dt-bindings/clock/exynos5420.h header and can be used in device +tree sources. Example 1: An example of a clock controller node is listed below. @@ -208,6 +36,6 @@ Example 2: UART controller node that consumes the clock generated by the clock compatible = "samsung,exynos4210-uart"; reg = <0x13820000 0x100>; interrupts = <0 54 0>; - clocks = <&clock 259>, <&clock 130>; + clocks = <&clock CLK_UART2>, <&clock CLK_SCLK_UART2>; clock-names = "uart", "clk_uart_baud0"; }; diff --git a/Documentation/devicetree/bindings/clock/exynos5440-clock.txt b/Documentation/devicetree/bindings/clock/exynos5440-clock.txt index 9955dc9c7d96..5f7005f73058 100644 --- a/Documentation/devicetree/bindings/clock/exynos5440-clock.txt +++ b/Documentation/devicetree/bindings/clock/exynos5440-clock.txt @@ -12,45 +12,12 @@ Required Properties: - #clock-cells: should be 1. -The following is the list of clocks generated by the controller. Each clock is -assigned an identifier and client nodes use this identifier to specify the -clock which they consume. - - - [Core Clocks] - - Clock ID - ---------------------------- - - xtal 1 - arm_clk 2 - - [Peripheral Clock Gates] - - Clock ID - ---------------------------- - - spi_baud 16 - pb0_250 17 - pr0_250 18 - pr1_250 19 - b_250 20 - b_125 21 - b_200 22 - sata 23 - usb 24 - gmac0 25 - cs250 26 - pb0_250_o 27 - pr0_250_o 28 - pr1_250_o 29 - b_250_o 30 - b_125_o 31 - b_200_o 32 - sata_o 33 - usb_o 34 - gmac0_o 35 - cs250_o 36 +Each clock is assigned an identifier and client nodes can use this identifier +to specify the clock which they consume. + +All available clocks are defined as preprocessor macros in +dt-bindings/clock/exynos5440.h header and can be used in device +tree sources. Example: An example of a clock controller node is listed below. diff --git a/Documentation/devicetree/bindings/clock/hi3620-clock.txt b/Documentation/devicetree/bindings/clock/hi3620-clock.txt index 4b71ab41be53..dad6269f52c5 100644 --- a/Documentation/devicetree/bindings/clock/hi3620-clock.txt +++ b/Documentation/devicetree/bindings/clock/hi3620-clock.txt @@ -7,6 +7,7 @@ Required Properties: - compatible: should be one of the following. - "hisilicon,hi3620-clock" - controller compatible with Hi3620 SoC. + - "hisilicon,hi3620-mmc-clock" - controller specific for Hi3620 mmc. - reg: physical base address of the controller and length of memory mapped region. diff --git a/Documentation/devicetree/bindings/clock/moxa,moxart-clock.txt b/Documentation/devicetree/bindings/clock/moxa,moxart-clock.txt new file mode 100644 index 000000000000..fedea84314a1 --- /dev/null +++ b/Documentation/devicetree/bindings/clock/moxa,moxart-clock.txt @@ -0,0 +1,48 @@ +Device Tree Clock bindings for arch-moxart + +This binding uses the common clock binding[1]. + +[1] Documentation/devicetree/bindings/clock/clock-bindings.txt + +MOXA ART SoCs allow to determine PLL output and APB frequencies +by reading registers holding multiplier and divisor information. + + +PLL: + +Required properties: +- compatible : Must be "moxa,moxart-pll-clock" +- #clock-cells : Should be 0 +- reg : Should contain registers location and length +- clocks : Should contain phandle + clock-specifier for the parent clock + +Optional properties: +- clock-output-names : Should contain clock name + + +APB: + +Required properties: +- compatible : Must be "moxa,moxart-apb-clock" +- #clock-cells : Should be 0 +- reg : Should contain registers location and length +- clocks : Should contain phandle + clock-specifier for the parent clock + +Optional properties: +- clock-output-names : Should contain clock name + + +For example: + + clk_pll: clk_pll@98100000 { + compatible = "moxa,moxart-pll-clock"; + #clock-cells = <0>; + reg = <0x98100000 0x34>; + }; + + clk_apb: clk_apb@98100000 { + compatible = "moxa,moxart-apb-clock"; + #clock-cells = <0>; + reg = <0x98100000 0x34>; + clocks = <&clk_pll>; + }; diff --git a/Documentation/devicetree/bindings/clock/mvebu-core-clock.txt b/Documentation/devicetree/bindings/clock/mvebu-core-clock.txt index 1e662948661e..307a503c5db8 100644 --- a/Documentation/devicetree/bindings/clock/mvebu-core-clock.txt +++ b/Documentation/devicetree/bindings/clock/mvebu-core-clock.txt @@ -11,6 +11,18 @@ The following is a list of provided IDs and clock names on Armada 370/XP: 3 = hclk (DRAM control clock) 4 = dramclk (DDR clock) +The following is a list of provided IDs and clock names on Armada 375: + 0 = tclk (Internal Bus clock) + 1 = cpuclk (CPU clock) + 2 = l2clk (L2 Cache clock) + 3 = ddrclk (DDR clock) + +The following is a list of provided IDs and clock names on Armada 380/385: + 0 = tclk (Internal Bus clock) + 1 = cpuclk (CPU clock) + 2 = l2clk (L2 Cache clock) + 3 = ddrclk (DDR clock) + The following is a list of provided IDs and clock names on Kirkwood and Dove: 0 = tclk (Internal Bus clock) 1 = cpuclk (CPU0 clock) @@ -20,6 +32,8 @@ The following is a list of provided IDs and clock names on Kirkwood and Dove: Required properties: - compatible : shall be one of the following: "marvell,armada-370-core-clock" - For Armada 370 SoC core clocks + "marvell,armada-375-core-clock" - For Armada 375 SoC core clocks + "marvell,armada-380-core-clock" - For Armada 380/385 SoC core clocks "marvell,armada-xp-core-clock" - For Armada XP SoC core clocks "marvell,dove-core-clock" - for Dove SoC core clocks "marvell,kirkwood-core-clock" - for Kirkwood SoC (except mv88f6180) diff --git a/Documentation/devicetree/bindings/clock/mvebu-corediv-clock.txt b/Documentation/devicetree/bindings/clock/mvebu-corediv-clock.txt index c62391fc0e39..520562a7dc2a 100644 --- a/Documentation/devicetree/bindings/clock/mvebu-corediv-clock.txt +++ b/Documentation/devicetree/bindings/clock/mvebu-corediv-clock.txt @@ -4,7 +4,10 @@ The following is a list of provided IDs and clock names on Armada 370/XP: 0 = nand (NAND clock) Required properties: -- compatible : must be "marvell,armada-370-corediv-clock" +- compatible : must be "marvell,armada-370-corediv-clock", + "marvell,armada-375-corediv-clock", + "marvell,armada-380-corediv-clock", + - reg : must be the register address of Core Divider control register - #clock-cells : from common clock binding; shall be set to 1 - clocks : must be set to the parent's phandle diff --git a/Documentation/devicetree/bindings/clock/mvebu-gated-clock.txt b/Documentation/devicetree/bindings/clock/mvebu-gated-clock.txt index fc2910fa7e45..76477be742b2 100644 --- a/Documentation/devicetree/bindings/clock/mvebu-gated-clock.txt +++ b/Documentation/devicetree/bindings/clock/mvebu-gated-clock.txt @@ -1,9 +1,10 @@ * Gated Clock bindings for Marvell EBU SoCs -Marvell Armada 370/XP, Dove and Kirkwood allow some peripheral clocks to be -gated to save some power. The clock consumer should specify the desired clock -by having the clock ID in its "clocks" phandle cell. The clock ID is directly -mapped to the corresponding clock gating control bit in HW to ease manual clock +Marvell Armada 370/375/380/385/XP, Dove and Kirkwood allow some +peripheral clocks to be gated to save some power. The clock consumer +should specify the desired clock by having the clock ID in its +"clocks" phandle cell. The clock ID is directly mapped to the +corresponding clock gating control bit in HW to ease manual clock lookup in datasheet. The following is a list of provided IDs for Armada 370: @@ -22,6 +23,60 @@ ID Clock Peripheral 28 ddr DDR Cntrl 30 sata1 SATA Host 0 +The following is a list of provided IDs for Armada 375: +ID Clock Peripheral +----------------------------------- +2 mu Management Unit +3 pp Packet Processor +4 ptp PTP +5 pex0 PCIe 0 Clock out +6 pex1 PCIe 1 Clock out +8 audio Audio Cntrl +11 nd_clk Nand Flash Cntrl +14 sata0_link SATA 0 Link +15 sata0_core SATA 0 Core +16 usb3 USB3 Host +17 sdio SDHCI Host +18 usb USB Host +19 gop Gigabit Ethernet MAC +20 sata1_link SATA 1 Link +21 sata1_core SATA 1 Core +22 xor0 XOR DMA 0 +23 xor1 XOR DMA 0 +24 copro Coprocessor +25 tdm Time Division Mplx +28 crypto0_enc Cryptographic Unit Port 0 Encryption +29 crypto0_core Cryptographic Unit Port 0 Core +30 crypto1_enc Cryptographic Unit Port 1 Encryption +31 crypto1_core Cryptographic Unit Port 1 Core + +The following is a list of provided IDs for Armada 380/385: +ID Clock Peripheral +----------------------------------- +0 audio Audio +2 ge2 Gigabit Ethernet 2 +3 ge1 Gigabit Ethernet 1 +4 ge0 Gigabit Ethernet 0 +5 pex1 PCIe 1 +6 pex2 PCIe 2 +7 pex3 PCIe 3 +8 pex0 PCIe 0 +9 usb3h0 USB3 Host 0 +10 usb3h1 USB3 Host 1 +11 usb3d USB3 Device +13 bm Buffer Management +14 crypto0z Cryptographic 0 Z +15 sata0 SATA 0 +16 crypto1z Cryptographic 1 Z +17 sdio SDIO +18 usb2 USB 2 +21 crypto1 Cryptographic 1 +22 xor0 XOR 0 +23 crypto0 Cryptographic 0 +25 tdm Time Division Multiplexing +28 xor1 XOR 1 +30 sata1 SATA 1 + The following is a list of provided IDs for Armada XP: ID Clock Peripheral ----------------------------------- @@ -95,6 +150,8 @@ ID Clock Peripheral Required properties: - compatible : shall be one of the following: "marvell,armada-370-gating-clock" - for Armada 370 SoC clock gating + "marvell,armada-375-gating-clock" - for Armada 375 SoC clock gating + "marvell,armada-380-gating-clock" - for Armada 380/385 SoC clock gating "marvell,armada-xp-gating-clock" - for Armada XP SoC clock gating "marvell,dove-gating-clock" - for Dove SoC clock gating "marvell,kirkwood-gating-clock" - for Kirkwood SoC clock gating diff --git a/Documentation/devicetree/bindings/clock/renesas,rz-cpg-clocks.txt b/Documentation/devicetree/bindings/clock/renesas,rz-cpg-clocks.txt new file mode 100644 index 000000000000..98a257492522 --- /dev/null +++ b/Documentation/devicetree/bindings/clock/renesas,rz-cpg-clocks.txt @@ -0,0 +1,29 @@ +* Renesas RZ Clock Pulse Generator (CPG) + +The CPG generates core clocks for the RZ SoCs. It includes the PLL, variable +CPU and GPU clocks, and several fixed ratio dividers. + +Required Properties: + + - compatible: Must be one of + - "renesas,r7s72100-cpg-clocks" for the r7s72100 CPG + - "renesas,rz-cpg-clocks" for the generic RZ CPG + - reg: Base address and length of the memory resource used by the CPG + - clocks: References to possible parent clocks. Order must match clock modes + in the datasheet. For the r7s72100, this is extal, usb_x1. + - #clock-cells: Must be 1 + - clock-output-names: The names of the clocks. Supported clocks are "pll", + "i", and "g" + + +Example +------- + + cpg_clocks: cpg_clocks@fcfe0000 { + #clock-cells = <1>; + compatible = "renesas,r7s72100-cpg-clocks", + "renesas,rz-cpg-clocks"; + reg = <0xfcfe0000 0x18>; + clocks = <&extal_clk>, <&usb_x1_clk>; + clock-output-names = "pll", "i", "g"; + }; diff --git a/Documentation/devicetree/bindings/clock/st/st,clkgen-divmux.txt b/Documentation/devicetree/bindings/clock/st/st,clkgen-divmux.txt new file mode 100644 index 000000000000..ae56315fcec5 --- /dev/null +++ b/Documentation/devicetree/bindings/clock/st/st,clkgen-divmux.txt @@ -0,0 +1,49 @@ +Binding for a ST divider and multiplexer clock driver. + +This binding uses the common clock binding[1]. +Base address is located to the parent node. See clock binding[2] + +[1] Documentation/devicetree/bindings/clock/clock-bindings.txt +[2] Documentation/devicetree/bindings/clock/st/st,clkgen.txt + +Required properties: + +- compatible : shall be: + "st,clkgena-divmux-c65-hs", "st,clkgena-divmux" + "st,clkgena-divmux-c65-ls", "st,clkgena-divmux" + "st,clkgena-divmux-c32-odf0", "st,clkgena-divmux" + "st,clkgena-divmux-c32-odf1", "st,clkgena-divmux" + "st,clkgena-divmux-c32-odf2", "st,clkgena-divmux" + "st,clkgena-divmux-c32-odf3", "st,clkgena-divmux" + +- #clock-cells : From common clock binding; shall be set to 1. + +- clocks : From common clock binding + +- clock-output-names : From common clock binding. + +Example: + + clockgenA@fd345000 { + reg = <0xfd345000 0xb50>; + + CLK_M_A1_DIV1: CLK_M_A1_DIV1 { + #clock-cells = <1>; + compatible = "st,clkgena-divmux-c32-odf1", + "st,clkgena-divmux"; + + clocks = <&CLK_M_A1_OSC_PREDIV>, + <&CLK_M_A1_PLL0 1>, /* PLL0 PHI1 */ + <&CLK_M_A1_PLL1 1>; /* PLL1 PHI1 */ + + clock-output-names = "CLK_M_RX_ICN_TS", + "CLK_M_RX_ICN_VDP_0", + "", /* Unused */ + "CLK_M_PRV_T1_BUS", + "CLK_M_ICN_REG_12", + "CLK_M_ICN_REG_10", + "", /* Unused */ + "CLK_M_ICN_ST231"; + }; + }; + diff --git a/Documentation/devicetree/bindings/clock/st/st,clkgen-mux.txt b/Documentation/devicetree/bindings/clock/st/st,clkgen-mux.txt new file mode 100644 index 000000000000..943e0808e212 --- /dev/null +++ b/Documentation/devicetree/bindings/clock/st/st,clkgen-mux.txt @@ -0,0 +1,36 @@ +Binding for a ST multiplexed clock driver. + +This binding supports only simple indexed multiplexers, it does not +support table based parent index to hardware value translations. + +This binding uses the common clock binding[1]. + +[1] Documentation/devicetree/bindings/clock/clock-bindings.txt + +Required properties: + +- compatible : shall be: + "st,stih416-clkgenc-vcc-hd", "st,clkgen-mux" + "st,stih416-clkgenf-vcc-fvdp", "st,clkgen-mux" + "st,stih416-clkgenf-vcc-hva", "st,clkgen-mux" + "st,stih416-clkgenf-vcc-hd", "st,clkgen-mux" + "st,stih416-clkgenf-vcc-sd", "st,clkgen-mux" + "st,stih415-clkgen-a9-mux", "st,clkgen-mux" + "st,stih416-clkgen-a9-mux", "st,clkgen-mux" + + +- #clock-cells : from common clock binding; shall be set to 0. + +- reg : A Base address and length of the register set. + +- clocks : from common clock binding + +Example: + + CLK_M_HVA: CLK_M_HVA { + #clock-cells = <0>; + compatible = "st,stih416-clkgenf-vcc-hva", "st,clkgen-mux"; + reg = <0xfd690868 4>; + + clocks = <&CLOCKGEN_F 1>, <&CLK_M_A1_DIV0 3>; + }; diff --git a/Documentation/devicetree/bindings/clock/st/st,clkgen-pll.txt b/Documentation/devicetree/bindings/clock/st/st,clkgen-pll.txt new file mode 100644 index 000000000000..81eb3855ab92 --- /dev/null +++ b/Documentation/devicetree/bindings/clock/st/st,clkgen-pll.txt @@ -0,0 +1,48 @@ +Binding for a ST pll clock driver. + +This binding uses the common clock binding[1]. +Base address is located to the parent node. See clock binding[2] + +[1] Documentation/devicetree/bindings/clock/clock-bindings.txt +[2] Documentation/devicetree/bindings/clock/st/st,clkgen.txt + +Required properties: + +- compatible : shall be: + "st,clkgena-prediv-c65", "st,clkgena-prediv" + "st,clkgena-prediv-c32", "st,clkgena-prediv" + + "st,clkgena-plls-c65" + "st,plls-c32-a1x-0", "st,clkgen-plls-c32" + "st,plls-c32-a1x-1", "st,clkgen-plls-c32" + "st,stih415-plls-c32-a9", "st,clkgen-plls-c32" + "st,stih415-plls-c32-ddr", "st,clkgen-plls-c32" + "st,stih416-plls-c32-a9", "st,clkgen-plls-c32" + "st,stih416-plls-c32-ddr", "st,clkgen-plls-c32" + + "st,stih415-gpu-pll-c32", "st,clkgengpu-pll-c32" + "st,stih416-gpu-pll-c32", "st,clkgengpu-pll-c32" + + +- #clock-cells : From common clock binding; shall be set to 1. + +- clocks : From common clock binding + +- clock-output-names : From common clock binding. + +Example: + + clockgenA@fee62000 { + reg = <0xfee62000 0xb48>; + + CLK_S_A0_PLL: CLK_S_A0_PLL { + #clock-cells = <1>; + compatible = "st,clkgena-plls-c65"; + + clocks = <&CLK_SYSIN>; + + clock-output-names = "CLK_S_A0_PLL0_HS", + "CLK_S_A0_PLL0_LS", + "CLK_S_A0_PLL1"; + }; + }; diff --git a/Documentation/devicetree/bindings/clock/st/st,clkgen-prediv.txt b/Documentation/devicetree/bindings/clock/st/st,clkgen-prediv.txt new file mode 100644 index 000000000000..566c9d79ed32 --- /dev/null +++ b/Documentation/devicetree/bindings/clock/st/st,clkgen-prediv.txt @@ -0,0 +1,36 @@ +Binding for a ST pre-divider clock driver. + +This binding uses the common clock binding[1]. +Base address is located to the parent node. See clock binding[2] + +[1] Documentation/devicetree/bindings/clock/clock-bindings.txt +[2] Documentation/devicetree/bindings/clock/st/st,clkgen.txt + +Required properties: + +- compatible : shall be: + "st,clkgena-prediv-c65", "st,clkgena-prediv" + "st,clkgena-prediv-c32", "st,clkgena-prediv" + +- #clock-cells : From common clock binding; shall be set to 0. + +- clocks : From common clock binding + +- clock-output-names : From common clock binding. + +Example: + + clockgenA@fd345000 { + reg = <0xfd345000 0xb50>; + + CLK_M_A2_OSC_PREDIV: CLK_M_A2_OSC_PREDIV { + #clock-cells = <0>; + compatible = "st,clkgena-prediv-c32", + "st,clkgena-prediv"; + + clocks = <&CLK_SYSIN>; + + clock-output-names = "CLK_M_A2_OSC_PREDIV"; + }; + }; + diff --git a/Documentation/devicetree/bindings/clock/st/st,clkgen-vcc.txt b/Documentation/devicetree/bindings/clock/st/st,clkgen-vcc.txt new file mode 100644 index 000000000000..4e3ff28b04c3 --- /dev/null +++ b/Documentation/devicetree/bindings/clock/st/st,clkgen-vcc.txt @@ -0,0 +1,53 @@ +Binding for a type of STMicroelectronics clock crossbar (VCC). + +The crossbar can take up to 4 input clocks and control up to 16 +output clocks. Not all inputs or outputs have to be in use in a +particular instantiation. Each output can be individually enabled, +select any of the input clocks and apply a divide (by 1,2,4 or 8) to +that selected clock. + +This binding uses the common clock binding[1]. + +[1] Documentation/devicetree/bindings/clock/clock-bindings.txt + +Required properties: + +- compatible : shall be: + "st,stih416-clkgenc", "st,vcc" + "st,stih416-clkgenf", "st,vcc" + +- #clock-cells : from common clock binding; shall be set to 1. + +- reg : A Base address and length of the register set. + +- clocks : from common clock binding + +- clock-output-names : From common clock binding. The block has 16 + clock outputs but not all of them in a specific instance + have to be used in the SoC. If a clock name is left as + an empty string then no clock will be created for the + output associated with that string index. If fewer than + 16 strings are provided then no clocks will be created + for the remaining outputs. + +Example: + + CLOCKGEN_C_VCC: CLOCKGEN_C_VCC { + #clock-cells = <1>; + compatible = "st,stih416-clkgenc", "st,clkgen-vcc"; + reg = <0xfe8308ac 12>; + + clocks = <&CLK_S_VCC_HD>, <&CLOCKGEN_C 1>, + <&CLK_S_TMDS_FROMPHY>, <&CLOCKGEN_C 2>; + + clock-output-names = + "CLK_S_PIX_HDMI", "CLK_S_PIX_DVO", + "CLK_S_OUT_DVO", "CLK_S_PIX_HD", + "CLK_S_HDDAC", "CLK_S_DENC", + "CLK_S_SDDAC", "CLK_S_PIX_MAIN", + "CLK_S_PIX_AUX", "CLK_S_STFE_FRC_0", + "CLK_S_REF_MCRU", "CLK_S_SLAVE_MCRU", + "CLK_S_TMDS_HDMI", "CLK_S_HDMI_REJECT_PLL", + "CLK_S_THSENS"; + }; + diff --git a/Documentation/devicetree/bindings/clock/st/st,clkgen.txt b/Documentation/devicetree/bindings/clock/st/st,clkgen.txt new file mode 100644 index 000000000000..49ec5ae18b5b --- /dev/null +++ b/Documentation/devicetree/bindings/clock/st/st,clkgen.txt @@ -0,0 +1,83 @@ +Binding for a Clockgen hardware block found on +certain STMicroelectronics consumer electronics SoC devices. + +A Clockgen node can contain pll, diviser or multiplexer nodes. + +We will find only the base address of the Clockgen, this base +address is common of all subnode. + + clockgen_node { + reg = <>; + + pll_node { + ... + }; + + prediv_node { + ... + }; + + divmux_node { + ... + }; + + quadfs_node { + ... + }; + ... + }; + +This binding uses the common clock binding[1]. +Each subnode should use the binding discribe in [2]..[4] + +[1] Documentation/devicetree/bindings/clock/clock-bindings.txt +[2] Documentation/devicetree/bindings/clock/st,quadfs.txt +[3] Documentation/devicetree/bindings/clock/st,quadfs.txt +[4] Documentation/devicetree/bindings/clock/st,quadfs.txt + +Required properties: +- reg : A Base address and length of the register set. + +Example: + + clockgenA@fee62000 { + + reg = <0xfee62000 0xb48>; + + CLK_S_A0_PLL: CLK_S_A0_PLL { + #clock-cells = <1>; + compatible = "st,clkgena-plls-c65"; + + clocks = <&CLK_SYSIN>; + + clock-output-names = "CLK_S_A0_PLL0_HS", + "CLK_S_A0_PLL0_LS", + "CLK_S_A0_PLL1"; + }; + + CLK_S_A0_OSC_PREDIV: CLK_S_A0_OSC_PREDIV { + #clock-cells = <0>; + compatible = "st,clkgena-prediv-c65", + "st,clkgena-prediv"; + + clocks = <&CLK_SYSIN>; + + clock-output-names = "CLK_S_A0_OSC_PREDIV"; + }; + + CLK_S_A0_HS: CLK_S_A0_HS { + #clock-cells = <1>; + compatible = "st,clkgena-divmux-c65-hs", + "st,clkgena-divmux"; + + clocks = <&CLK_S_A0_OSC_PREDIV>, + <&CLK_S_A0_PLL 0>, /* PLL0 HS */ + <&CLK_S_A0_PLL 2>; /* PLL1 */ + + clock-output-names = "CLK_S_FDMA_0", + "CLK_S_FDMA_1", + ""; /* CLK_S_JIT_SENSE */ + /* Fourth output unused */ + }; + }; + diff --git a/Documentation/devicetree/bindings/clock/st/st,quadfs.txt b/Documentation/devicetree/bindings/clock/st/st,quadfs.txt new file mode 100644 index 000000000000..ec86d62ca283 --- /dev/null +++ b/Documentation/devicetree/bindings/clock/st/st,quadfs.txt @@ -0,0 +1,45 @@ +Binding for a type of quad channel digital frequency synthesizer found on +certain STMicroelectronics consumer electronics SoC devices. + +This version contains a programmable PLL which can generate up to 216, 432 +or 660MHz (from a 30MHz oscillator input) as the input to the digital +synthesizers. + +This binding uses the common clock binding[1]. + +[1] Documentation/devicetree/bindings/clock/clock-bindings.txt + +Required properties: +- compatible : shall be: + "st,stih416-quadfs216", "st,quadfs" + "st,stih416-quadfs432", "st,quadfs" + "st,stih416-quadfs660-E", "st,quadfs" + "st,stih416-quadfs660-F", "st,quadfs" + +- #clock-cells : from common clock binding; shall be set to 1. + +- reg : A Base address and length of the register set. + +- clocks : from common clock binding + +- clock-output-names : From common clock binding. The block has 4 + clock outputs but not all of them in a specific instance + have to be used in the SoC. If a clock name is left as + an empty string then no clock will be created for the + output associated with that string index. If fewer than + 4 strings are provided then no clocks will be created + for the remaining outputs. + +Example: + + CLOCKGEN_E: CLOCKGEN_E { + #clock-cells = <1>; + compatible = "st,stih416-quadfs660-E", "st,quadfs"; + reg = <0xfd3208bc 0xB0>; + + clocks = <&CLK_SYSIN>; + clock-output-names = "CLK_M_PIX_MDTP_0", + "CLK_M_PIX_MDTP_1", + "CLK_M_PIX_MDTP_2", + "CLK_M_MPELPC"; + }; diff --git a/Documentation/devicetree/bindings/clock/sunxi.txt b/Documentation/devicetree/bindings/clock/sunxi.txt index c2cb7621ad2d..a5160d8cbb5f 100644 --- a/Documentation/devicetree/bindings/clock/sunxi.txt +++ b/Documentation/devicetree/bindings/clock/sunxi.txt @@ -6,37 +6,41 @@ This binding uses the common clock binding[1]. Required properties: - compatible : shall be one of the following: - "allwinner,sun4i-osc-clk" - for a gatable oscillator - "allwinner,sun4i-pll1-clk" - for the main PLL clock and PLL4 + "allwinner,sun4i-a10-osc-clk" - for a gatable oscillator + "allwinner,sun4i-a10-pll1-clk" - for the main PLL clock and PLL4 "allwinner,sun6i-a31-pll1-clk" - for the main PLL clock on A31 - "allwinner,sun4i-pll5-clk" - for the PLL5 clock - "allwinner,sun4i-pll6-clk" - for the PLL6 clock - "allwinner,sun4i-cpu-clk" - for the CPU multiplexer clock - "allwinner,sun4i-axi-clk" - for the AXI clock - "allwinner,sun4i-axi-gates-clk" - for the AXI gates - "allwinner,sun4i-ahb-clk" - for the AHB clock - "allwinner,sun4i-ahb-gates-clk" - for the AHB gates on A10 + "allwinner,sun4i-a10-pll5-clk" - for the PLL5 clock + "allwinner,sun4i-a10-pll6-clk" - for the PLL6 clock + "allwinner,sun6i-a31-pll6-clk" - for the PLL6 clock on A31 + "allwinner,sun4i-a10-cpu-clk" - for the CPU multiplexer clock + "allwinner,sun4i-a10-axi-clk" - for the AXI clock + "allwinner,sun4i-a10-axi-gates-clk" - for the AXI gates + "allwinner,sun4i-a10-ahb-clk" - for the AHB clock + "allwinner,sun4i-a10-ahb-gates-clk" - for the AHB gates on A10 "allwinner,sun5i-a13-ahb-gates-clk" - for the AHB gates on A13 "allwinner,sun5i-a10s-ahb-gates-clk" - for the AHB gates on A10s "allwinner,sun7i-a20-ahb-gates-clk" - for the AHB gates on A20 "allwinner,sun6i-a31-ahb1-mux-clk" - for the AHB1 multiplexer on A31 "allwinner,sun6i-a31-ahb1-gates-clk" - for the AHB1 gates on A31 - "allwinner,sun4i-apb0-clk" - for the APB0 clock - "allwinner,sun4i-apb0-gates-clk" - for the APB0 gates on A10 + "allwinner,sun4i-a10-apb0-clk" - for the APB0 clock + "allwinner,sun4i-a10-apb0-gates-clk" - for the APB0 gates on A10 "allwinner,sun5i-a13-apb0-gates-clk" - for the APB0 gates on A13 "allwinner,sun5i-a10s-apb0-gates-clk" - for the APB0 gates on A10s "allwinner,sun7i-a20-apb0-gates-clk" - for the APB0 gates on A20 - "allwinner,sun4i-apb1-clk" - for the APB1 clock - "allwinner,sun4i-apb1-mux-clk" - for the APB1 clock muxing - "allwinner,sun4i-apb1-gates-clk" - for the APB1 gates on A10 + "allwinner,sun4i-a10-apb1-clk" - for the APB1 clock + "allwinner,sun4i-a10-apb1-mux-clk" - for the APB1 clock muxing + "allwinner,sun4i-a10-apb1-gates-clk" - for the APB1 gates on A10 "allwinner,sun5i-a13-apb1-gates-clk" - for the APB1 gates on A13 "allwinner,sun5i-a10s-apb1-gates-clk" - for the APB1 gates on A10s "allwinner,sun6i-a31-apb1-gates-clk" - for the APB1 gates on A31 "allwinner,sun7i-a20-apb1-gates-clk" - for the APB1 gates on A20 "allwinner,sun6i-a31-apb2-div-clk" - for the APB2 gates on A31 "allwinner,sun6i-a31-apb2-gates-clk" - for the APB2 gates on A31 - "allwinner,sun4i-mod0-clk" - for the module 0 family of clocks + "allwinner,sun4i-a10-mod0-clk" - for the module 0 family of clocks "allwinner,sun7i-a20-out-clk" - for the external output clocks + "allwinner,sun7i-a20-gmac-clk" - for the GMAC clock module on A20/A31 + "allwinner,sun4i-a10-usb-clk" - for usb gates + resets on A10 / A20 + "allwinner,sun5i-a13-usb-clk" - for usb gates + resets on A13 Required properties for all clocks: - reg : shall be the control register address for the clock. @@ -44,10 +48,17 @@ Required properties for all clocks: multiplexed clocks, the list order must match the hardware programming order. - #clock-cells : from common clock binding; shall be set to 0 except for - "allwinner,*-gates-clk" where it shall be set to 1 + "allwinner,*-gates-clk", "allwinner,sun4i-pll5-clk" and + "allwinner,sun4i-pll6-clk" where it shall be set to 1 +- clock-output-names : shall be the corresponding names of the outputs. + If the clock module only has one output, the name shall be the + module name. -Additionally, "allwinner,*-gates-clk" clocks require: -- clock-output-names : the corresponding gate names that the clock controls +And "allwinner,*-usb-clk" clocks also require: +- reset-cells : shall be set to 1 + +For "allwinner,sun7i-a20-gmac-clk", the parent clocks shall be fixed rate +dummy clocks at 25 MHz and 125 MHz, respectively. See example. Clock consumers should specify the desired clocks they use with a "clocks" phandle cell. Consumers that are using a gated clock should @@ -56,23 +67,68 @@ offset of the bit controlling this particular gate in the register. For example: -osc24M: osc24M@01c20050 { +osc24M: clk@01c20050 { #clock-cells = <0>; - compatible = "allwinner,sun4i-osc-clk"; + compatible = "allwinner,sun4i-a10-osc-clk"; reg = <0x01c20050 0x4>; clocks = <&osc24M_fixed>; + clock-output-names = "osc24M"; }; -pll1: pll1@01c20000 { +pll1: clk@01c20000 { #clock-cells = <0>; - compatible = "allwinner,sun4i-pll1-clk"; + compatible = "allwinner,sun4i-a10-pll1-clk"; reg = <0x01c20000 0x4>; clocks = <&osc24M>; + clock-output-names = "pll1"; +}; + +pll5: clk@01c20020 { + #clock-cells = <1>; + compatible = "allwinner,sun4i-pll5-clk"; + reg = <0x01c20020 0x4>; + clocks = <&osc24M>; + clock-output-names = "pll5_ddr", "pll5_other"; }; cpu: cpu@01c20054 { #clock-cells = <0>; - compatible = "allwinner,sun4i-cpu-clk"; + compatible = "allwinner,sun4i-a10-cpu-clk"; reg = <0x01c20054 0x4>; clocks = <&osc32k>, <&osc24M>, <&pll1>; + clock-output-names = "cpu"; +}; + +mmc0_clk: clk@01c20088 { + #clock-cells = <0>; + compatible = "allwinner,sun4i-mod0-clk"; + reg = <0x01c20088 0x4>; + clocks = <&osc24M>, <&pll6 1>, <&pll5 1>; + clock-output-names = "mmc0"; +}; + +mii_phy_tx_clk: clk@2 { + #clock-cells = <0>; + compatible = "fixed-clock"; + clock-frequency = <25000000>; + clock-output-names = "mii_phy_tx"; +}; + +gmac_int_tx_clk: clk@3 { + #clock-cells = <0>; + compatible = "fixed-clock"; + clock-frequency = <125000000>; + clock-output-names = "gmac_int_tx"; +}; + +gmac_clk: clk@01c20164 { + #clock-cells = <0>; + compatible = "allwinner,sun7i-a20-gmac-clk"; + reg = <0x01c20164 0x4>; + /* + * The first clock must be fixed at 25MHz; + * the second clock must be fixed at 125MHz + */ + clocks = <&mii_phy_tx_clk>, <&gmac_int_tx_clk>; + clock-output-names = "gmac"; }; diff --git a/Documentation/devicetree/bindings/clock/zynq-7000.txt b/Documentation/devicetree/bindings/clock/zynq-7000.txt index 17b4a94916d6..d93746cf2975 100644 --- a/Documentation/devicetree/bindings/clock/zynq-7000.txt +++ b/Documentation/devicetree/bindings/clock/zynq-7000.txt @@ -14,6 +14,7 @@ for all clock consumers of PS clocks. Required properties: - #clock-cells : Must be 1 - compatible : "xlnx,ps7-clkc" + - reg : SLCR offset and size taken via syscon < 0x100 0x100 > - ps-clk-frequency : Frequency of the oscillator providing ps_clk in HZ (usually 33 MHz oscillators are used for Zynq platforms) - clock-output-names : List of strings used to name the clock outputs. Shall be @@ -87,10 +88,11 @@ Clock outputs: 47: dbg_apb Example: - clkc: clkc { + clkc: clkc@100 { #clock-cells = <1>; compatible = "xlnx,ps7-clkc"; ps-clk-frequency = <33333333>; + reg = <0x100 0x100>; clock-output-names = "armpll", "ddrpll", "iopll", "cpu_6or4x", "cpu_3or2x", "cpu_2x", "cpu_1x", "ddr2x", "ddr3x", "dci", "lqspi", "smc", "pcap", "gem0", "gem1", |