diff options
Diffstat (limited to 'Documentation/admin-guide/perf/hisi-pcie-pmu.rst')
| -rw-r--r-- | Documentation/admin-guide/perf/hisi-pcie-pmu.rst | 112 |
1 files changed, 68 insertions, 44 deletions
diff --git a/Documentation/admin-guide/perf/hisi-pcie-pmu.rst b/Documentation/admin-guide/perf/hisi-pcie-pmu.rst index 294ebbdb22af..7e863662e2d4 100644 --- a/Documentation/admin-guide/perf/hisi-pcie-pmu.rst +++ b/Documentation/admin-guide/perf/hisi-pcie-pmu.rst @@ -15,10 +15,10 @@ HiSilicon PCIe PMU driver The PCIe PMU driver registers a perf PMU with the name of its sicl-id and PCIe Core id.:: - /sys/bus/event_source/hisi_pcie<sicl>_<core> + /sys/bus/event_source/hisi_pcie<sicl>_core<core> PMU driver provides description of available events and filter options in sysfs, -see /sys/bus/event_source/devices/hisi_pcie<sicl>_<core>. +see /sys/bus/event_source/devices/hisi_pcie<sicl>_core<core>. The "format" directory describes all formats of the config (events) and config1 (filter options) fields of the perf_event_attr structure. The "events" directory @@ -33,13 +33,13 @@ monitored by PMU. Example usage of perf:: $# perf list - hisi_pcie0_0/rx_mwr_latency/ [kernel PMU event] - hisi_pcie0_0/rx_mwr_cnt/ [kernel PMU event] + hisi_pcie0_core0/rx_mwr_latency/ [kernel PMU event] + hisi_pcie0_core0/rx_mwr_cnt/ [kernel PMU event] ------------------------------------------ - $# perf stat -e hisi_pcie0_0/rx_mwr_latency/ - $# perf stat -e hisi_pcie0_0/rx_mwr_cnt/ - $# perf stat -g -e hisi_pcie0_0/rx_mwr_latency/ -e hisi_pcie0_0/rx_mwr_cnt/ + $# perf stat -e hisi_pcie0_core0/rx_mwr_latency/ + $# perf stat -e hisi_pcie0_core0/rx_mwr_cnt/ + $# perf stat -g -e hisi_pcie0_core0/rx_mwr_latency/ -e hisi_pcie0_core0/rx_mwr_cnt/ The current driver does not support sampling. So "perf record" is unsupported. Also attach to a task is unsupported for PCIe PMU. @@ -48,59 +48,83 @@ Filter options -------------- 1. Target filter -PMU could only monitor the performance of traffic downstream target Root Ports -or downstream target Endpoint. PCIe PMU driver support "port" and "bdf" -interfaces for users, and these two interfaces aren't supported at the same -time. --port -"port" filter can be used in all PCIe PMU events, target Root Port can be -selected by configuring the 16-bits-bitmap "port". Multi ports can be selected -for AP-layer-events, and only one port can be selected for TL/DL-layer-events. + PMU could only monitor the performance of traffic downstream target Root + Ports or downstream target Endpoint. PCIe PMU driver support "port" and + "bdf" interfaces for users, and these two interfaces aren't supported at the + same time. -For example, if target Root Port is 0000:00:00.0 (x8 lanes), bit0 of bitmap -should be set, port=0x1; if target Root Port is 0000:00:04.0 (x4 lanes), -bit8 is set, port=0x100; if these two Root Ports are both monitored, port=0x101. + - port -Example usage of perf:: + "port" filter can be used in all PCIe PMU events, target Root Port can be + selected by configuring the 16-bits-bitmap "port". Multi ports can be + selected for AP-layer-events, and only one port can be selected for + TL/DL-layer-events. - $# perf stat -e hisi_pcie0_0/rx_mwr_latency,port=0x1/ sleep 5 + For example, if target Root Port is 0000:00:00.0 (x8 lanes), bit0 of + bitmap should be set, port=0x1; if target Root Port is 0000:00:04.0 (x4 + lanes), bit8 is set, port=0x100; if these two Root Ports are both + monitored, port=0x101. --bdf + Example usage of perf:: -"bdf" filter can only be used in bandwidth events, target Endpoint is selected -by configuring BDF to "bdf". Counter only counts the bandwidth of message -requested by target Endpoint. + $# perf stat -e hisi_pcie0_core0/rx_mwr_latency,port=0x1/ sleep 5 -For example, "bdf=0x3900" means BDF of target Endpoint is 0000:39:00.0. + - bdf -Example usage of perf:: + "bdf" filter can only be used in bandwidth events, target Endpoint is + selected by configuring BDF to "bdf". Counter only counts the bandwidth of + message requested by target Endpoint. + + For example, "bdf=0x3900" means BDF of target Endpoint is 0000:39:00.0. + + Example usage of perf:: - $# perf stat -e hisi_pcie0_0/rx_mrd_flux,bdf=0x3900/ sleep 5 + $# perf stat -e hisi_pcie0_core0/rx_mrd_flux,bdf=0x3900/ sleep 5 2. Trigger filter -Event statistics start when the first time TLP length is greater/smaller -than trigger condition. You can set the trigger condition by writing "trig_len", -and set the trigger mode by writing "trig_mode". This filter can only be used -in bandwidth events. -For example, "trig_len=4" means trigger condition is 2^4 DW, "trig_mode=0" -means statistics start when TLP length > trigger condition, "trig_mode=1" -means start when TLP length < condition. + Event statistics start when the first time TLP length is greater/smaller + than trigger condition. You can set the trigger condition by writing + "trig_len", and set the trigger mode by writing "trig_mode". This filter can + only be used in bandwidth events. -Example usage of perf:: + For example, "trig_len=4" means trigger condition is 2^4 DW, "trig_mode=0" + means statistics start when TLP length > trigger condition, "trig_mode=1" + means start when TLP length < condition. + + Example usage of perf:: - $# perf stat -e hisi_pcie0_0/rx_mrd_flux,trig_len=0x4,trig_mode=1/ sleep 5 + $# perf stat -e hisi_pcie0_core0/rx_mrd_flux,trig_len=0x4,trig_mode=1/ sleep 5 3. Threshold filter -Counter counts when TLP length within the specified range. You can set the -threshold by writing "thr_len", and set the threshold mode by writing -"thr_mode". This filter can only be used in bandwidth events. -For example, "thr_len=4" means threshold is 2^4 DW, "thr_mode=0" means -counter counts when TLP length >= threshold, and "thr_mode=1" means counts -when TLP length < threshold. + Counter counts when TLP length within the specified range. You can set the + threshold by writing "thr_len", and set the threshold mode by writing + "thr_mode". This filter can only be used in bandwidth events. -Example usage of perf:: + For example, "thr_len=4" means threshold is 2^4 DW, "thr_mode=0" means + counter counts when TLP length >= threshold, and "thr_mode=1" means counts + when TLP length < threshold. + + Example usage of perf:: + + $# perf stat -e hisi_pcie0_core0/rx_mrd_flux,thr_len=0x4,thr_mode=1/ sleep 5 + +4. TLP Length filter + + When counting bandwidth, the data can be composed of certain parts of TLP + packets. You can specify it through "len_mode": + + - 2'b00: Reserved (Do not use this since the behaviour is undefined) + - 2'b01: Bandwidth of TLP payloads + - 2'b10: Bandwidth of TLP headers + - 2'b11: Bandwidth of both TLP payloads and headers + + For example, "len_mode=2" means only counting the bandwidth of TLP headers + and "len_mode=3" means the final bandwidth data is composed of both TLP + headers and payloads. Default value if not specified is 2'b11. + + Example usage of perf:: - $# perf stat -e hisi_pcie0_0/rx_mrd_flux,thr_len=0x4,thr_mode=1/ sleep 5 + $# perf stat -e hisi_pcie0_core0/rx_mrd_flux,len_mode=0x1/ sleep 5 |