diff options
| -rw-r--r-- | arch/arm/boot/dts/am335x-pepper.dts | 2 | ||||
| -rw-r--r-- | arch/arm/boot/dts/dra7.dtsi | 3 | ||||
| -rw-r--r-- | arch/arm/boot/dts/dra76-evm.dts | 1 | ||||
| -rw-r--r-- | arch/arm/boot/dts/logicpd-som-lv-35xx-devkit.dts | 17 | ||||
| -rw-r--r-- | arch/arm/boot/dts/logicpd-som-lv-37xx-devkit.dts | 249 | ||||
| -rw-r--r-- | arch/arm/boot/dts/logicpd-som-lv-baseboard.dtsi | 256 | ||||
| -rw-r--r-- | arch/arm/boot/dts/logicpd-som-lv.dtsi | 27 | ||||
| -rw-r--r-- | arch/arm/boot/dts/logicpd-torpedo-35xx-devkit.dts | 17 | ||||
| -rw-r--r-- | arch/arm/boot/dts/logicpd-torpedo-37xx-devkit.dts | 411 | ||||
| -rw-r--r-- | arch/arm/boot/dts/logicpd-torpedo-baseboard.dtsi | 395 | ||||
| -rw-r--r-- | arch/arm/boot/dts/logicpd-torpedo-som.dtsi | 84 | ||||
| -rw-r--r-- | arch/arm/boot/dts/omap3-n900.dts | 4 |
12 files changed, 735 insertions, 731 deletions
diff --git a/arch/arm/boot/dts/am335x-pepper.dts b/arch/arm/boot/dts/am335x-pepper.dts index 03c7d77023c6..9fb7426070ce 100644 --- a/arch/arm/boot/dts/am335x-pepper.dts +++ b/arch/arm/boot/dts/am335x-pepper.dts @@ -139,7 +139,7 @@ &audio_codec { status = "okay"; - gpio-reset = <&gpio1 16 GPIO_ACTIVE_LOW>; + reset-gpios = <&gpio1 16 GPIO_ACTIVE_LOW>; AVDD-supply = <&ldo3_reg>; IOVDD-supply = <&ldo3_reg>; DRVDD-supply = <&ldo3_reg>; diff --git a/arch/arm/boot/dts/dra7.dtsi b/arch/arm/boot/dts/dra7.dtsi index a1d7178a3966..3c8c0d743dd0 100644 --- a/arch/arm/boot/dts/dra7.dtsi +++ b/arch/arm/boot/dts/dra7.dtsi @@ -1561,6 +1561,7 @@ dr_mode = "otg"; snps,dis_u3_susphy_quirk; snps,dis_u2_susphy_quirk; + snps,dis_metastability_quirk; }; }; @@ -1929,6 +1930,8 @@ clocks = <&dss_clkctrl DRA7_DSS_CORE_CLKCTRL 9>, <&dss_clkctrl DRA7_DSS_CORE_CLKCTRL 10>; clock-names = "fck", "sys_clk"; + dmas = <&sdma_xbar 76>; + dma-names = "audio_tx"; }; }; diff --git a/arch/arm/boot/dts/dra76-evm.dts b/arch/arm/boot/dts/dra76-evm.dts index b024a65c6e27..f64aab450315 100644 --- a/arch/arm/boot/dts/dra76-evm.dts +++ b/arch/arm/boot/dts/dra76-evm.dts @@ -148,6 +148,7 @@ compatible = "ti,tps65917"; reg = <0x58>; ti,system-power-controller; + ti,palmas-override-powerhold; interrupt-controller; #interrupt-cells = <2>; diff --git a/arch/arm/boot/dts/logicpd-som-lv-35xx-devkit.dts b/arch/arm/boot/dts/logicpd-som-lv-35xx-devkit.dts new file mode 100644 index 000000000000..32d0dc371fc3 --- /dev/null +++ b/arch/arm/boot/dts/logicpd-som-lv-35xx-devkit.dts @@ -0,0 +1,17 @@ +/* + * This program is free software; you can redistribute it and/or modify + * it under the terms of the GNU General Public License version 2 as + * published by the Free Software Foundation. + */ + +/dts-v1/; + +#include "omap34xx.dtsi" +#include "logicpd-som-lv.dtsi" +#include "logicpd-som-lv-baseboard.dtsi" +#include "omap-gpmc-smsc9221.dtsi" + +/ { + model = "LogicPD Zoom OMAP35xx SOM-LV Development Kit"; + compatible = "logicpd,dm3730-som-lv-devkit", "ti,omap3"; +}; diff --git a/arch/arm/boot/dts/logicpd-som-lv-37xx-devkit.dts b/arch/arm/boot/dts/logicpd-som-lv-37xx-devkit.dts index 2fa5eb4bd402..24283739526c 100644 --- a/arch/arm/boot/dts/logicpd-som-lv-37xx-devkit.dts +++ b/arch/arm/boot/dts/logicpd-som-lv-37xx-devkit.dts @@ -8,257 +8,10 @@ #include "omap36xx.dtsi" #include "logicpd-som-lv.dtsi" +#include "logicpd-som-lv-baseboard.dtsi" #include "omap-gpmc-smsc9221.dtsi" / { model = "LogicPD Zoom DM3730 SOM-LV Development Kit"; compatible = "logicpd,dm3730-som-lv-devkit", "ti,omap3630", "ti,omap3"; - - gpio_keys { - compatible = "gpio-keys"; - pinctrl-names = "default"; - pinctrl-0 = <&gpio_key_pins>; - - sysboot2 { - label = "gpio3"; - gpios = <&gpio4 15 GPIO_ACTIVE_LOW>; /* gpio_111 / uP_GPIO_3 */ - linux,code = <BTN_0>; - wakeup-source; - }; - }; - - sound { - compatible = "ti,omap-twl4030"; - ti,model = "omap3logic"; - ti,mcbsp = <&mcbsp2>; - }; - - leds { - compatible = "gpio-leds"; - pinctrl-names = "default"; - pinctrl-0 = <&led_pins &led_pins_wkup>; - - led1 { - label = "led1"; - gpios = <&gpio5 5 GPIO_ACTIVE_LOW>; /* gpio133 */ - linux,default-trigger = "cpu0"; - }; - - led2 { - label = "led2"; - gpios = <&gpio1 11 GPIO_ACTIVE_LOW>; /* gpio11 */ - linux,default-trigger = "none"; - }; - }; -}; - -&vaux1 { - regulator-min-microvolt = <3000000>; - regulator-max-microvolt = <3000000>; -}; - -&vaux4 { - regulator-min-microvolt = <1800000>; - regulator-max-microvolt = <1800000>; -}; - -&mcbsp2 { - status = "okay"; -}; - -&charger { - ti,bb-uvolt = <3200000>; - ti,bb-uamp = <150>; -}; - -&gpmc { - ranges = <0 0 0x30000000 0x1000000 /* CS0: 16MB for NAND */ - 1 0 0x2c000000 0x1000000>; /* CS1: 16MB for LAN9221 */ - - ethernet@gpmc { - pinctrl-names = "default"; - pinctrl-0 = <&lan9221_pins>; - interrupt-parent = <&gpio5>; - interrupts = <24 IRQ_TYPE_LEVEL_LOW>; /* gpio_152 */ - reg = <1 0 0xff>; - }; -}; - -&vpll2 { - regulator-always-on; -}; - -&dss { - status = "ok"; - vdds_dsi-supply = <&vpll2>; - vdda_video-supply = <&video_reg>; - pinctrl-names = "default"; - pinctrl-0 = <&dss_dpi_pins1>; - port { - dpi_out: endpoint { - remote-endpoint = <&lcd_in>; - data-lines = <16>; - }; - }; -}; - -/ { - aliases { - display0 = &lcd0; - }; - - video_reg: video_reg { - compatible = "regulator-fixed"; - regulator-name = "fixed-supply"; - regulator-min-microvolt = <3300000>; - regulator-max-microvolt = <3300000>; - }; - - lcd0: display@0 { - compatible = "panel-dpi"; - label = "28"; - status = "okay"; - /* default-on; */ - pinctrl-names = "default"; - pinctrl-0 = <&lcd_enable_pin>; - enable-gpios = <&gpio5 27 GPIO_ACTIVE_HIGH>; /* gpio155, lcd INI */ - port { - lcd_in: endpoint { - remote-endpoint = <&dpi_out>; - }; - }; - - panel-timing { - clock-frequency = <9000000>; - hactive = <480>; - vactive = <272>; - hfront-porch = <3>; - hback-porch = <2>; - hsync-len = <42>; - vback-porch = <3>; - vfront-porch = <2>; - vsync-len = <11>; - hsync-active = <1>; - vsync-active = <1>; - de-active = <1>; - pixelclk-active = <0>; - }; - }; - - bl: backlight { - compatible = "pwm-backlight"; - pinctrl-names = "default"; - pinctrl-0 = <&backlight_pins>; - pwms = <&twl_pwm 0 5000000>; - brightness-levels = <0 10 20 30 40 50 60 70 80 90 100>; - default-brightness-level = <7>; - enable-gpios = <&gpio1 8 GPIO_ACTIVE_HIGH>; /* gpio_8 */ - }; -}; - -&mmc1 { - interrupts-extended = <&intc 83 &omap3_pmx_core 0x11a>; - pinctrl-names = "default"; - pinctrl-0 = <&mmc1_pins>; - wp-gpios = <&gpio4 30 GPIO_ACTIVE_HIGH>; /* gpio_126 */ - cd-gpios = <&gpio4 14 IRQ_TYPE_LEVEL_LOW>; /* gpio_110 */ - vmmc-supply = <&vmmc1>; - bus-width = <4>; - cap-power-off-card; -}; - -&omap3_pmx_core { - gpio_key_pins: pinmux_gpio_key_pins { - pinctrl-single,pins = < - OMAP3_CORE1_IOPAD(0x212e, PIN_INPUT_PULLUP | MUX_MODE4) /* cam_xclkb.gpio_111 / uP_GPIO_3*/ - >; - }; - - led_pins: pinmux_led_pins { - pinctrl-single,pins = < - OMAP3_CORE1_IOPAD(0x215e, PIN_OUTPUT_PULLUP | MUX_MODE4) /* sdmmc2_dat1.gpio_133 / uP_GPIO_0 */ - >; - }; - - lan9221_pins: pinmux_lan9221_pins { - pinctrl-single,pins = < - OMAP3_CORE1_IOPAD(0x2184, PIN_INPUT_PULLUP | MUX_MODE4) /* mcbsp4_clkx.gpio_152 */ - >; - }; - - mmc1_pins: pinmux_mmc1_pins { - pinctrl-single,pins = < - OMAP3_CORE1_IOPAD(0x2144, PIN_OUTPUT | MUX_MODE0) /* sdmmc1_clk.sdmmc1_clk */ - OMAP3_CORE1_IOPAD(0x2146, PIN_INPUT | MUX_MODE0) /* sdmmc1_cmd.sdmmc1_cmd */ - OMAP3_CORE1_IOPAD(0x2148, PIN_INPUT | MUX_MODE0) /* sdmmc1_dat0.sdmmc1_dat0 */ - OMAP3_CORE1_IOPAD(0x214a, PIN_INPUT | MUX_MODE0) /* sdmmc1_dat1.sdmmc1_dat1 */ - OMAP3_CORE1_IOPAD(0x214c, PIN_INPUT | MUX_MODE0) /* sdmmc1_dat2.sdmmc1_dat2 */ - OMAP3_CORE1_IOPAD(0x214e, PIN_INPUT | MUX_MODE0) /* sdmmc1_dat3.sdmmc1_dat3 */ - OMAP3_CORE1_IOPAD(0x2132, PIN_INPUT_PULLUP | MUX_MODE4) /* cam_strobe.gpio_126 */ - OMAP3_CORE1_IOPAD(0x212c, PIN_INPUT_PULLUP | MUX_MODE4) /* cam_d11.gpio_110 */ - >; - }; - - lcd_enable_pin: pinmux_lcd_enable_pin { - pinctrl-single,pins = < - OMAP3_CORE1_IOPAD(0x218a, PIN_OUTPUT | PIN_OFF_OUTPUT_LOW | MUX_MODE4) /* mcbsp4_fs.gpio_155 */ - >; - }; - - dss_dpi_pins1: pinmux_dss_dpi_pins1 { - pinctrl-single,pins = < - OMAP3_CORE1_IOPAD(0x20d4, PIN_OUTPUT_PULLDOWN | PIN_OFF_OUTPUT_LOW | MUX_MODE0) /* dss_pclk.dss_pclk */ - OMAP3_CORE1_IOPAD(0x20d6, PIN_OUTPUT_PULLDOWN | PIN_OFF_OUTPUT_LOW | MUX_MODE0) /* dss_hsync.dss_hsync */ - OMAP3_CORE1_IOPAD(0x20d8, PIN_OUTPUT_PULLDOWN | PIN_OFF_OUTPUT_LOW | MUX_MODE0) /* dss_vsync.dss_vsync */ - OMAP3_CORE1_IOPAD(0x20da, PIN_OUTPUT_PULLDOWN | PIN_OFF_OUTPUT_LOW | MUX_MODE0) /* dss_acbias.dss_acbias */ - - OMAP3_CORE1_IOPAD(0x20dc, PIN_OUTPUT_PULLDOWN | PIN_OFF_OUTPUT_LOW | MUX_MODE0) /* dss_data0.dss_data0 */ - OMAP3_CORE1_IOPAD(0x20de, PIN_OUTPUT_PULLDOWN | PIN_OFF_OUTPUT_LOW | MUX_MODE0) /* dss_data1.dss_data1 */ - OMAP3_CORE1_IOPAD(0x20e0, PIN_OUTPUT_PULLDOWN | PIN_OFF_OUTPUT_LOW | MUX_MODE0) /* dss_data2.dss_data2 */ - OMAP3_CORE1_IOPAD(0x20e2, PIN_OUTPUT_PULLDOWN | PIN_OFF_OUTPUT_LOW | MUX_MODE0) /* dss_data3.dss_data3 */ - OMAP3_CORE1_IOPAD(0x20e4, PIN_OUTPUT_PULLDOWN | PIN_OFF_OUTPUT_LOW | MUX_MODE0) /* dss_data4.dss_data4 */ - OMAP3_CORE1_IOPAD(0x20e6, PIN_OUTPUT_PULLDOWN | PIN_OFF_OUTPUT_LOW | MUX_MODE0) /* dss_data5.dss_data5 */ - OMAP3_CORE1_IOPAD(0x20e8, PIN_OUTPUT_PULLDOWN | PIN_OFF_OUTPUT_LOW | MUX_MODE0) /* dss_data6.dss_data6 */ - OMAP3_CORE1_IOPAD(0x20ea, PIN_OUTPUT_PULLDOWN | PIN_OFF_OUTPUT_LOW | MUX_MODE0) /* dss_data7.dss_data7 */ - OMAP3_CORE1_IOPAD(0x20ec, PIN_OUTPUT_PULLDOWN | PIN_OFF_OUTPUT_LOW | MUX_MODE0) /* dss_data8.dss_data8 */ - OMAP3_CORE1_IOPAD(0x20ee, PIN_OUTPUT_PULLDOWN | PIN_OFF_OUTPUT_LOW | MUX_MODE0) /* dss_data9.dss_data9 */ - OMAP3_CORE1_IOPAD(0x20f0, PIN_OUTPUT_PULLDOWN | PIN_OFF_OUTPUT_LOW | MUX_MODE0) /* dss_data10.dss_data10 */ - OMAP3_CORE1_IOPAD(0x20f2, PIN_OUTPUT_PULLDOWN | PIN_OFF_OUTPUT_LOW | MUX_MODE0) /* dss_data11.dss_data11 */ - OMAP3_CORE1_IOPAD(0x20f4, PIN_OUTPUT_PULLDOWN | PIN_OFF_OUTPUT_LOW | MUX_MODE0) /* dss_data12.dss_data12 */ - OMAP3_CORE1_IOPAD(0x20f6, PIN_OUTPUT_PULLDOWN | PIN_OFF_OUTPUT_LOW | MUX_MODE0) /* dss_data13.dss_data13 */ - OMAP3_CORE1_IOPAD(0x20f8, PIN_OUTPUT_PULLDOWN | PIN_OFF_OUTPUT_LOW | MUX_MODE0) /* dss_data14.dss_data14 */ - OMAP3_CORE1_IOPAD(0x20fa, PIN_OUTPUT_PULLDOWN | PIN_OFF_OUTPUT_LOW | MUX_MODE0) /* dss_data15.dss_data15 */ - >; - }; -}; - -&omap3_pmx_wkup { - led_pins_wkup: pinmux_led_pins_wkup { - pinctrl-single,pins = < - OMAP3_WKUP_IOPAD(0x2a24, PIN_OUTPUT_PULLUP | MUX_MODE4) /* jtag_emu0.gpio_11 / uP_GPIO_1 */ - >; - }; - - backlight_pins: pinmux_backlight_pins { - pinctrl-single,pins = < - OMAP3_WKUP_IOPAD(0x2a16, PIN_OUTPUT | PIN_OFF_OUTPUT_LOW | MUX_MODE4) /* sys_boot6.gpio_8 */ - >; - }; -}; - - -&uart1 { - interrupts-extended = <&intc 72 &omap3_pmx_core OMAP3_UART1_RX>; -}; - -/* Wired to the tps65950 on the SOM, only the USB connector is on the devkit */ -&usb_otg_hs { - pinctrl-names = "default"; - pinctrl-0 = <&hsusb_otg_pins>; - interface-type = <0>; - usb-phy = <&usb2_phy>; - phys = <&usb2_phy>; - phy-names = "usb2-phy"; - mode = <3>; - power = <50>; }; diff --git a/arch/arm/boot/dts/logicpd-som-lv-baseboard.dtsi b/arch/arm/boot/dts/logicpd-som-lv-baseboard.dtsi new file mode 100644 index 000000000000..4990ed90dcea --- /dev/null +++ b/arch/arm/boot/dts/logicpd-som-lv-baseboard.dtsi @@ -0,0 +1,256 @@ +/* + * This program is free software; you can redistribute it and/or modify + * it under the terms of the GNU General Public License version 2 as + * published by the Free Software Foundation. + */ + +/ { + gpio_keys { + compatible = "gpio-keys"; + pinctrl-names = "default"; + pinctrl-0 = <&gpio_key_pins>; + + sysboot2 { + label = "gpio3"; + gpios = <&gpio4 15 GPIO_ACTIVE_LOW>; /* gpio_111 / uP_GPIO_3 */ + linux,code = <BTN_0>; + wakeup-source; + }; + }; + + sound { + compatible = "ti,omap-twl4030"; + ti,model = "omap3logic"; + ti,mcbsp = <&mcbsp2>; + }; + + leds { + compatible = "gpio-leds"; + pinctrl-names = "default"; + pinctrl-0 = <&led_pins &led_pins_wkup>; + + led1 { + label = "led1"; + gpios = <&gpio5 5 GPIO_ACTIVE_LOW>; /* gpio133 */ + linux,default-trigger = "cpu0"; + }; + + led2 { + label = "led2"; + gpios = <&gpio1 11 GPIO_ACTIVE_LOW>; /* gpio11 */ + linux,default-trigger = "none"; + }; + }; +}; + +&vaux1 { + regulator-min-microvolt = <3000000>; + regulator-max-microvolt = <3000000>; +}; + +&vaux4 { + regulator-min-microvolt = <1800000>; + regulator-max-microvolt = <1800000>; +}; + +&mcbsp2 { + status = "okay"; +}; + +&charger { + ti,bb-uvolt = <3200000>; + ti,bb-uamp = <150>; +}; + +&gpmc { + ranges = <0 0 0x30000000 0x1000000 /* CS0: 16MB for NAND */ + 1 0 0x2c000000 0x1000000 /* CS1: 16MB for LAN9221 */ + 2 0 0x10000000 0x2000000>; /* CS2: 32MB for NOR */ + + ethernet@gpmc { + pinctrl-names = "default"; + pinctrl-0 = <&lan9221_pins>; + interrupt-parent = <&gpio5>; + interrupts = <24 IRQ_TYPE_LEVEL_LOW>; /* gpio_152 */ + reg = <1 0 0xff>; + }; +}; + +&vpll2 { + regulator-always-on; +}; + +&dss { + status = "ok"; + vdds_dsi-supply = <&vpll2>; + vdda_video-supply = <&video_reg>; + pinctrl-names = "default"; + pinctrl-0 = <&dss_dpi_pins1>; + port { + dpi_out: endpoint { + remote-endpoint = <&lcd_in>; + data-lines = <16>; + }; + }; +}; + +/ { + aliases { + display0 = &lcd0; + }; + + video_reg: video_reg { + compatible = "regulator-fixed"; + regulator-name = "fixed-supply"; + regulator-min-microvolt = <3300000>; + regulator-max-microvolt = <3300000>; + }; + + lcd0: display@0 { + compatible = "panel-dpi"; + label = "28"; + status = "okay"; + /* default-on; */ + pinctrl-names = "default"; + pinctrl-0 = <&lcd_enable_pin>; + enable-gpios = <&gpio5 27 GPIO_ACTIVE_HIGH>; /* gpio155, lcd INI */ + port { + lcd_in: endpoint { + remote-endpoint = <&dpi_out>; + }; + }; + + panel-timing { + clock-frequency = <9000000>; + hactive = <480>; + vactive = <272>; + hfront-porch = <3>; + hback-porch = <2>; + hsync-len = <42>; + vback-porch = <3>; + vfront-porch = <2>; + vsync-len = <11>; + hsync-active = <1>; + vsync-active = <1>; + de-active = <1>; + pixelclk-active = <0>; + }; + }; + + bl: backlight { + compatible = "pwm-backlight"; + pinctrl-names = "default"; + pinctrl-0 = <&backlight_pins>; + pwms = <&twl_pwm 0 5000000>; + brightness-levels = <0 10 20 30 40 50 60 70 80 90 100>; + default-brightness-level = <7>; + enable-gpios = <&gpio1 8 GPIO_ACTIVE_HIGH>; /* gpio_8 */ + }; +}; + +&mmc1 { + interrupts-extended = <&intc 83 &omap3_pmx_core 0x11a>; + pinctrl-names = "default"; + pinctrl-0 = <&mmc1_pins>; + wp-gpios = <&gpio4 30 GPIO_ACTIVE_HIGH>; /* gpio_126 */ + cd-gpios = <&gpio4 14 IRQ_TYPE_LEVEL_LOW>; /* gpio_110 */ + vmmc-supply = <&vmmc1>; + bus-width = <4>; + cap-power-off-card; +}; + +&omap3_pmx_core { + gpio_key_pins: pinmux_gpio_key_pins { + pinctrl-single,pins = < + OMAP3_CORE1_IOPAD(0x212e, PIN_INPUT_PULLUP | MUX_MODE4) /* cam_xclkb.gpio_111 / uP_GPIO_3*/ + >; + }; + + led_pins: pinmux_led_pins { + pinctrl-single,pins = < + OMAP3_CORE1_IOPAD(0x215e, PIN_OUTPUT_PULLUP | MUX_MODE4) /* sdmmc2_dat1.gpio_133 / uP_GPIO_0 */ + >; + }; + + lan9221_pins: pinmux_lan9221_pins { + pinctrl-single,pins = < + OMAP3_CORE1_IOPAD(0x2184, PIN_INPUT_PULLUP | MUX_MODE4) /* mcbsp4_clkx.gpio_152 */ + >; + }; + + mmc1_pins: pinmux_mmc1_pins { + pinctrl-single,pins = < + OMAP3_CORE1_IOPAD(0x2144, PIN_OUTPUT | MUX_MODE0) /* sdmmc1_clk.sdmmc1_clk */ + OMAP3_CORE1_IOPAD(0x2146, PIN_INPUT | MUX_MODE0) /* sdmmc1_cmd.sdmmc1_cmd */ + OMAP3_CORE1_IOPAD(0x2148, PIN_INPUT | MUX_MODE0) /* sdmmc1_dat0.sdmmc1_dat0 */ + OMAP3_CORE1_IOPAD(0x214a, PIN_INPUT | MUX_MODE0) /* sdmmc1_dat1.sdmmc1_dat1 */ + OMAP3_CORE1_IOPAD(0x214c, PIN_INPUT | MUX_MODE0) /* sdmmc1_dat2.sdmmc1_dat2 */ + OMAP3_CORE1_IOPAD(0x214e, PIN_INPUT | MUX_MODE0) /* sdmmc1_dat3.sdmmc1_dat3 */ + OMAP3_CORE1_IOPAD(0x2132, PIN_INPUT_PULLUP | MUX_MODE4) /* cam_strobe.gpio_126 */ + OMAP3_CORE1_IOPAD(0x212c, PIN_INPUT_PULLUP | MUX_MODE4) /* cam_d11.gpio_110 */ + >; + }; + + lcd_enable_pin: pinmux_lcd_enable_pin { + pinctrl-single,pins = < + OMAP3_CORE1_IOPAD(0x218a, PIN_OUTPUT | PIN_OFF_OUTPUT_LOW | MUX_MODE4) /* mcbsp4_fs.gpio_155 */ + >; + }; + + dss_dpi_pins1: pinmux_dss_dpi_pins1 { + pinctrl-single,pins = < + OMAP3_CORE1_IOPAD(0x20d4, PIN_OUTPUT_PULLDOWN | PIN_OFF_OUTPUT_LOW | MUX_MODE0) /* dss_pclk.dss_pclk */ + OMAP3_CORE1_IOPAD(0x20d6, PIN_OUTPUT_PULLDOWN | PIN_OFF_OUTPUT_LOW | MUX_MODE0) /* dss_hsync.dss_hsync */ + OMAP3_CORE1_IOPAD(0x20d8, PIN_OUTPUT_PULLDOWN | PIN_OFF_OUTPUT_LOW | MUX_MODE0) /* dss_vsync.dss_vsync */ + OMAP3_CORE1_IOPAD(0x20da, PIN_OUTPUT_PULLDOWN | PIN_OFF_OUTPUT_LOW | MUX_MODE0) /* dss_acbias.dss_acbias */ + + OMAP3_CORE1_IOPAD(0x20dc, PIN_OUTPUT_PULLDOWN | PIN_OFF_OUTPUT_LOW | MUX_MODE0) /* dss_data0.dss_data0 */ + OMAP3_CORE1_IOPAD(0x20de, PIN_OUTPUT_PULLDOWN | PIN_OFF_OUTPUT_LOW | MUX_MODE0) /* dss_data1.dss_data1 */ + OMAP3_CORE1_IOPAD(0x20e0, PIN_OUTPUT_PULLDOWN | PIN_OFF_OUTPUT_LOW | MUX_MODE0) /* dss_data2.dss_data2 */ + OMAP3_CORE1_IOPAD(0x20e2, PIN_OUTPUT_PULLDOWN | PIN_OFF_OUTPUT_LOW | MUX_MODE0) /* dss_data3.dss_data3 */ + OMAP3_CORE1_IOPAD(0x20e4, PIN_OUTPUT_PULLDOWN | PIN_OFF_OUTPUT_LOW | MUX_MODE0) /* dss_data4.dss_data4 */ + OMAP3_CORE1_IOPAD(0x20e6, PIN_OUTPUT_PULLDOWN | PIN_OFF_OUTPUT_LOW | MUX_MODE0) /* dss_data5.dss_data5 */ + OMAP3_CORE1_IOPAD(0x20e8, PIN_OUTPUT_PULLDOWN | PIN_OFF_OUTPUT_LOW | MUX_MODE0) /* dss_data6.dss_data6 */ + OMAP3_CORE1_IOPAD(0x20ea, PIN_OUTPUT_PULLDOWN | PIN_OFF_OUTPUT_LOW | MUX_MODE0) /* dss_data7.dss_data7 */ + OMAP3_CORE1_IOPAD(0x20ec, PIN_OUTPUT_PULLDOWN | PIN_OFF_OUTPUT_LOW | MUX_MODE0) /* dss_data8.dss_data8 */ + OMAP3_CORE1_IOPAD(0x20ee, PIN_OUTPUT_PULLDOWN | PIN_OFF_OUTPUT_LOW | MUX_MODE0) /* dss_data9.dss_data9 */ + OMAP3_CORE1_IOPAD(0x20f0, PIN_OUTPUT_PULLDOWN | PIN_OFF_OUTPUT_LOW | MUX_MODE0) /* dss_data10.dss_data10 */ + OMAP3_CORE1_IOPAD(0x20f2, PIN_OUTPUT_PULLDOWN | PIN_OFF_OUTPUT_LOW | MUX_MODE0) /* dss_data11.dss_data11 */ + OMAP3_CORE1_IOPAD(0x20f4, PIN_OUTPUT_PULLDOWN | PIN_OFF_OUTPUT_LOW | MUX_MODE0) /* dss_data12.dss_data12 */ + OMAP3_CORE1_IOPAD(0x20f6, PIN_OUTPUT_PULLDOWN | PIN_OFF_OUTPUT_LOW | MUX_MODE0) /* dss_data13.dss_data13 */ + OMAP3_CORE1_IOPAD(0x20f8, PIN_OUTPUT_PULLDOWN | PIN_OFF_OUTPUT_LOW | MUX_MODE0) /* dss_data14.dss_data14 */ + OMAP3_CORE1_IOPAD(0x20fa, PIN_OUTPUT_PULLDOWN | PIN_OFF_OUTPUT_LOW | MUX_MODE0) /* dss_data15.dss_data15 */ + >; + }; +}; + +&omap3_pmx_wkup { + led_pins_wkup: pinmux_led_pins_wkup { + pinctrl-single,pins = < + OMAP3_WKUP_IOPAD(0x2a24, PIN_OUTPUT_PULLUP | MUX_MODE4) /* jtag_emu0.gpio_11 / uP_GPIO_1 */ + >; + }; + + backlight_pins: pinmux_backlight_pins { + pinctrl-single,pins = < + OMAP3_WKUP_IOPAD(0x2a16, PIN_OUTPUT | PIN_OFF_OUTPUT_LOW | MUX_MODE4) /* sys_boot6.gpio_8 */ + >; + }; +}; + + +&uart1 { + interrupts-extended = <&intc 72 &omap3_pmx_core OMAP3_UART1_RX>; +}; + +/* Wired to the tps65950 on the SOM, only the USB connector is on the devkit */ +&usb_otg_hs { + pinctrl-names = "default"; + pinctrl-0 = <&hsusb_otg_pins>; + interface-type = <0>; + usb-phy = <&usb2_phy>; + phys = <&usb2_phy>; + phy-names = "usb2-phy"; + mode = <3>; + power = <50>; +}; diff --git a/arch/arm/boot/dts/logicpd-som-lv.dtsi b/arch/arm/boot/dts/logicpd-som-lv.dtsi index 29cb804d10cc..c1aa7a4518fb 100644 --- a/arch/arm/boot/dts/logicpd-som-lv.dtsi +++ b/arch/arm/boot/dts/logicpd-som-lv.dtsi @@ -67,33 +67,6 @@ gpmc,device-width = <2>; #address-cells = <1>; #size-cells = <1>; - - /* u-boot uses mtdparts=omap2-nand.0:512k(x-loader),1920k(u-boot),128k(u-boot-env),4m(kernel),-(fs) */ - - x-loader@0 { - label = "x-loader"; - reg = <0 0x80000>; - }; - - bootloaders@80000 { - label = "u-boot"; - reg = <0x80000 0x1e0000>; - }; - - bootloaders_env@260000 { - label = "u-boot-env"; - reg = <0x260000 0x20000>; - }; - - kernel@280000 { - label = "kernel"; - reg = <0x280000 0x400000>; - }; - - filesystem@680000 { - label = "fs"; - reg = <0x680000 0>; /* 0 = MTDPART_SIZ_FULL */ - }; }; }; diff --git a/arch/arm/boot/dts/logicpd-torpedo-35xx-devkit.dts b/arch/arm/boot/dts/logicpd-torpedo-35xx-devkit.dts new file mode 100644 index 000000000000..d7cb659656ce --- /dev/null +++ b/arch/arm/boot/dts/logicpd-torpedo-35xx-devkit.dts @@ -0,0 +1,17 @@ +/* + * This program is free software; you can redistribute it and/or modify + * it under the terms of the GNU General Public License version 2 as + * published by the Free Software Foundation. + */ + +/dts-v1/; + +#include "omap34xx.dtsi" +#include "logicpd-torpedo-som.dtsi" +#include "logicpd-torpedo-baseboard.dtsi" +#include "omap-gpmc-smsc9221.dtsi" + +/ { + model = "LogicPD Zoom OMAP35xx Torpedo Development Kit"; + compatible = "logicpd,dm3730-torpedo-devkit", "ti,omap3"; +}; diff --git a/arch/arm/boot/dts/logicpd-torpedo-37xx-devkit.dts b/arch/arm/boot/dts/logicpd-torpedo-37xx-devkit.dts index b4575bbaf085..234afd6d60ec 100644 --- a/arch/arm/boot/dts/logicpd-torpedo-37xx-devkit.dts +++ b/arch/arm/boot/dts/logicpd-torpedo-37xx-devkit.dts @@ -9,396 +9,69 @@ #include "omap36xx.dtsi" #include "logicpd-torpedo-som.dtsi" #include "omap-gpmc-smsc9221.dtsi" +#include "logicpd-torpedo-baseboard.dtsi" / { model = "LogicPD Zoom DM3730 Torpedo + Wireless Development Kit"; compatible = "logicpd,dm3730-torpedo-devkit", "ti,omap3630", "ti,omap3"; - gpio_keys { - compatible = "gpio-keys"; - pinctrl-names = "default"; - pinctrl-0 = <&gpio_key_pins &gpio_key_pins_wkup>; - - sysboot2 { - label = "sysboot2"; - gpios = <&gpio1 2 GPIO_ACTIVE_LOW>; /* gpio2 */ - linux,code = <BTN_0>; - wakeup-source; - }; - - sysboot5 { - label = "sysboot5"; - gpios = <&gpio1 7 GPIO_ACTIVE_LOW>; /* gpio7 */ - linux,code = <BTN_1>; - wakeup-source; - }; - - gpio1 { - label = "gpio1"; - gpios = <&gpio6 21 GPIO_ACTIVE_LOW>; /* gpio181 */ - linux,code = <BTN_2>; - wakeup-source; - }; - - gpio2 { - label = "gpio2"; - gpios = <&gpio6 18 GPIO_ACTIVE_LOW>; /* gpio178 */ - linux,code = <BTN_3>; - wakeup-source; - }; - }; - - sound { - compatible = "ti,omap-twl4030"; - ti,model = "omap3logic"; - ti,mcbsp = <&mcbsp2>; - }; - - leds { - compatible = "gpio-leds"; - pinctrl-names = "default"; - pinctrl-0 = <&led_pins>; - - led1 { - label = "led1"; - gpios = <&gpio6 20 GPIO_ACTIVE_HIGH>; /* gpio180 */ - linux,default-trigger = "cpu0"; - }; - - led2 { - label = "led2"; - gpios = <&gpio6 19 GPIO_ACTIVE_HIGH>; /* gpio179 */ - linux,default-trigger = "none"; - }; - }; - - pwm10: dmtimer-pwm { - compatible = "ti,omap-dmtimer-pwm"; - pinctrl-names = "default"; - pinctrl-0 = <&pwm_pins>; - ti,timers = <&timer10>; - #pwm-cells = <3>; - }; - -}; - -&vaux1 { - regulator-min-microvolt = <3000000>; - regulator-max-microvolt = <3000000>; -}; - -&vaux4 { - regulator-min-microvolt = <1800000>; - regulator-max-microvolt = <1800000>; -}; - -&mcbsp2 { - status = "okay"; -}; - -&charger { - ti,bb-uvolt = <3200000>; - ti,bb-uamp = <150>; -}; - -&gpmc { - ranges = <0 0 0x30000000 0x1000000 /* CS0: 16MB for NAND */ - 1 0 0x2c000000 0x1000000>; /* CS1: 16MB for LAN9221 */ - - ethernet@gpmc { - pinctrl-names = "default"; - pinctrl-0 = <&lan9221_pins>; - interrupt-parent = <&gpio5>; - interrupts = <1 IRQ_TYPE_LEVEL_LOW>; /* gpio129 */ - reg = <1 0 0xff>; - }; -}; - -&vpll2 { - regulator-always-on; -}; - -&dss { - status = "ok"; - vdds_dsi-supply = <&vpll2>; - vdda_video-supply = <&video_reg>; - pinctrl-names = "default"; - pinctrl-0 = <&dss_dpi_pins1>; - port { - dpi_out: endpoint { - remote-endpoint = <&lcd_in>; - data-lines = <16>; - }; - }; -}; - -/ { - aliases { - display0 = &lcd0; - }; - - video_reg: video_reg { - pinctrl-names = "default"; - pinctrl-0 = <&panel_pwr_pins>; + wl12xx_vmmc: wl12xx_vmmc { compatible = "regulator-fixed"; - regulator-name = "fixed-supply"; - regulator-min-microvolt = <3300000>; - regulator-max-microvolt = <3300000>; - gpio = <&gpio5 27 GPIO_ACTIVE_HIGH>; /* gpio155, lcd INI */ - }; - - lcd0: display { - compatible = "panel-dpi"; - label = "15"; - status = "okay"; - /* default-on; */ - pinctrl-names = "default"; - - port { - lcd_in: endpoint { - remote-endpoint = <&dpi_out>; - }; - }; - - panel-timing { - clock-frequency = <9000000>; - hactive = <480>; - vactive = <272>; - hfront-porch = <3>; - hback-porch = <2>; - hsync-len = <42>; - vback-porch = <3>; - vfront-porch = <4>; - vsync-len = <11>; - hsync-active = <0>; - vsync-active = <0>; - de-active = <1>; - pixelclk-active = <1>; - }; - }; - - bl: backlight { - compatible = "pwm-backlight"; - pinctrl-names = "default"; - pinctrl-0 = <&backlight_pins>; - pwms = <&pwm10 0 5000000 0>; - brightness-levels = <0 10 20 30 40 50 60 70 80 90 100>; - default-brightness-level = <7>; - enable-gpios = <&gpio5 26 GPIO_ACTIVE_HIGH>; /* gpio_154 */ + regulator-name = "vwl1271"; + regulator-min-microvolt = <1800000>; + regulator-max-microvolt = <1800000>; + gpio = <&gpio5 29 0>; /* gpio157 */ + startup-delay-us = <70000>; + enable-active-high; + vin-supply = <&vmmc2>; }; }; -&mmc1 { - interrupts-extended = <&intc 83 &omap3_pmx_core 0x11a>; +/* + * Only found on the wireless SOM. For the SOM without wireless, the pins for + * MMC3 can be routed with jumpers to the second MMC slot on the devkit and + * gpio157 is not connected. So this should be OK to keep common for now, + * probably device tree overlays is the way to go with the various SOM and + * jumpering combinations for the long run. + */ +&mmc3 { + interrupts-extended = <&intc 94 &omap3_pmx_core2 0x46>; + pinctrl-0 = <&mmc3_pins &mmc3_core2_pins>; pinctrl-names = "default"; - pinctrl-0 = <&mmc1_pins &mmc1_cd>; - cd-gpios = <&gpio4 31 GPIO_ACTIVE_LOW>; /* gpio127 */ - vmmc-supply = <&vmmc1>; + vmmc-supply = <&wl12xx_vmmc>; + non-removable; bus-width = <4>; cap-power-off-card; + #address-cells = <1>; + #size-cells = <0>; + wlcore: wlcore@2 { + compatible = "ti,wl1283"; + reg = <2>; + interrupt-parent = <&gpio5>; + interrupts = <24 IRQ_TYPE_LEVEL_HIGH>; /* gpio 152 */ + ref-clock-frequency = <26000000>; + tcxo-clock-frequency = <26000000>; + }; }; &omap3_pmx_core { - gpio_key_pins: pinmux_gpio_key_pins { - pinctrl-single,pins = < - OMAP3_CORE1_IOPAD(0x21d6, PIN_INPUT_PULLUP | MUX_MODE4) /* mcspi2_clk.gpio_178 */ - OMAP3_CORE1_IOPAD(0x21dc, PIN_INPUT_PULLUP | MUX_MODE4) /* mcspi2_cs0.gpio_181 */ - >; - }; - - pwm_pins: pinmux_pwm_pins { - pinctrl-single,pins = < - OMAP3_CORE1_IOPAD(0x20B8, PIN_OUTPUT | PIN_OFF_OUTPUT_LOW | MUX_MODE3) /* gpmc_ncs5.gpt_10_pwm_evt */ - >; - }; - - led_pins: pinmux_led_pins { + mmc3_pins: pinmux_mm3_pins { pinctrl-single,pins = < - OMAP3_CORE1_IOPAD(0x21d8, PIN_OUTPUT | MUX_MODE4) /* gpio_179 */ - OMAP3_CORE1_IOPAD(0x21da, PIN_OUTPUT | MUX_MODE4) /* gpio_180 */ - >; - }; - - mmc1_pins: pinmux_mmc1_pins { - pinctrl-single,pins = < - OMAP3_CORE1_IOPAD(0x2144, PIN_OUTPUT | MUX_MODE0) /* sdmmc1_clk.sdmmc1_clk */ - OMAP3_CORE1_IOPAD(0x2146, PIN_INPUT | MUX_MODE0) /* sdmmc1_cmd.sdmmc1_cmd */ - OMAP3_CORE1_IOPAD(0x2148, PIN_INPUT | MUX_MODE0) /* sdmmc1_dat0.sdmmc1_dat0 */ - OMAP3_CORE1_IOPAD(0x214a, PIN_INPUT | MUX_MODE0) /* sdmmc1_dat1.sdmmc1_dat1 */ - OMAP3_CORE1_IOPAD(0x214c, PIN_INPUT | MUX_MODE0) /* sdmmc1_dat2.sdmmc1_dat2 */ - OMAP3_CORE1_IOPAD(0x214e, PIN_INPUT | MUX_MODE0) /* sdmmc1_dat3.sdmmc1_dat3 */ - >; - }; - - tsc2004_pins: pinmux_tsc2004_pins { - pinctrl-single,pins = < - OMAP3_CORE1_IOPAD(0x2186, PIN_INPUT | MUX_MODE4) /* mcbsp4_dr.gpio_153 */ - >; - }; - - backlight_pins: pinmux_backlight_pins { - pinctrl-single,pins = < - OMAP3_CORE1_IOPAD(0x2188, PIN_OUTPUT | PIN_OFF_OUTPUT_LOW | MUX_MODE4) /* mcbsp4_dx.gpio_154 */ - >; - }; - - isp_pins: pinmux_isp_pins { - pinctrl-single,pins = < - OMAP3_CORE1_IOPAD(0x210c, PIN_INPUT | MUX_MODE0) /* cam_hs.cam_hs */ - OMAP3_CORE1_IOPAD(0x210e, PIN_INPUT | MUX_MODE0) /* cam_vs.cam_vs */ - OMAP3_CORE1_IOPAD(0x2110, PIN_INPUT | MUX_MODE0) /* cam_xclka.cam_xclka */ - OMAP3_CORE1_IOPAD(0x2112, PIN_INPUT | MUX_MODE0) /* cam_pclk.cam_pclk */ - - OMAP3_CORE1_IOPAD(0x2116, PIN_INPUT | MUX_MODE0) /* cam_d0.cam_d0 */ - OMAP3_CORE1_IOPAD(0x2118, PIN_INPUT | MUX_MODE0) /* cam_d1.cam_d1 */ - OMAP3_CORE1_IOPAD(0x211a, PIN_INPUT | MUX_MODE0) /* cam_d2.cam_d2 */ - OMAP3_CORE1_IOPAD(0x211c, PIN_INPUT | MUX_MODE0) /* cam_d3.cam_d3 */ - OMAP3_CORE1_IOPAD(0x211e, PIN_INPUT | MUX_MODE0) /* cam_d4.cam_d4 */ - OMAP3_CORE1_IOPAD(0x2120, PIN_INPUT | MUX_MODE0) /* cam_d5.cam_d5 */ - OMAP3_CORE1_IOPAD(0x2122, PIN_INPUT | MUX_MODE0) /* cam_d6.cam_d6 */ - OMAP3_CORE1_IOPAD(0x2124, PIN_INPUT | MUX_MODE0) /* cam_d7.cam_d7 */ - >; - }; - - panel_pwr_pins: pinmux_panel_pwr_pins { - pinctrl-single,pins = < - OMAP3_CORE1_IOPAD(0x218a, PIN_OUTPUT | PIN_OFF_OUTPUT_LOW | MUX_MODE4) /* mcbsp4_fs.gpio_155 */ - >; - }; - - dss_dpi_pins1: pinmux_dss_dpi_pins1 { - pinctrl-single,pins = < - OMAP3_CORE1_IOPAD(0x20d4, PIN_OUTPUT_PULLDOWN | PIN_OFF_OUTPUT_LOW | MUX_MODE0) /* dss_pclk.dss_pclk */ - OMAP3_CORE1_IOPAD(0x20d6, PIN_OUTPUT_PULLDOWN | PIN_OFF_OUTPUT_LOW | MUX_MODE0) /* dss_hsync.dss_hsync */ - OMAP3_CORE1_IOPAD(0x20d8, PIN_OUTPUT_PULLDOWN | PIN_OFF_OUTPUT_LOW | MUX_MODE0) /* dss_vsync.dss_vsync */ - OMAP3_CORE1_IOPAD(0x20da, PIN_OUTPUT_PULLDOWN | PIN_OFF_OUTPUT_LOW | MUX_MODE0) /* dss_acbias.dss_acbias */ - - OMAP3_CORE1_IOPAD(0x20e8, PIN_OUTPUT_PULLDOWN | PIN_OFF_OUTPUT_LOW | MUX_MODE0) /* dss_data6.dss_data6 */ - OMAP3_CORE1_IOPAD(0x20ea, PIN_OUTPUT_PULLDOWN | PIN_OFF_OUTPUT_LOW | MUX_MODE0) /* dss_data7.dss_data7 */ - OMAP3_CORE1_IOPAD(0x20ec, PIN_OUTPUT_PULLDOWN | PIN_OFF_OUTPUT_LOW | MUX_MODE0) /* dss_data8.dss_data8 */ - OMAP3_CORE1_IOPAD(0x20ee, PIN_OUTPUT_PULLDOWN | PIN_OFF_OUTPUT_LOW | MUX_MODE0) /* dss_data9.dss_data9 */ - OMAP3_CORE1_IOPAD(0x20f0, PIN_OUTPUT_PULLDOWN | PIN_OFF_OUTPUT_LOW | MUX_MODE0) /* dss_data10.dss_data10 */ - OMAP3_CORE1_IOPAD(0x20f2, PIN_OUTPUT_PULLDOWN | PIN_OFF_OUTPUT_LOW | MUX_MODE0) /* dss_data11.dss_data11 */ - OMAP3_CORE1_IOPAD(0x20f4, PIN_OUTPUT_PULLDOWN | PIN_OFF_OUTPUT_LOW | MUX_MODE0) /* dss_data12.dss_data12 */ - OMAP3_CORE1_IOPAD(0x20f6, PIN_OUTPUT_PULLDOWN | PIN_OFF_OUTPUT_LOW | MUX_MODE0) /* dss_data13.dss_data13 */ - OMAP3_CORE1_IOPAD(0x20f8, PIN_OUTPUT_PULLDOWN | PIN_OFF_OUTPUT_LOW | MUX_MODE0) /* dss_data14.dss_data14 */ - OMAP3_CORE1_IOPAD(0x20fa, PIN_OUTPUT_PULLDOWN | PIN_OFF_OUTPUT_LOW | MUX_MODE0) /* dss_data15.dss_data15 */ - OMAP3_CORE1_IOPAD(0x20fc, PIN_OUTPUT_PULLDOWN | PIN_OFF_OUTPUT_LOW | MUX_MODE0) /* dss_data16.dss_data16 */ - OMAP3_CORE1_IOPAD(0x20fe, PIN_OUTPUT_PULLDOWN | PIN_OFF_OUTPUT_LOW | MUX_MODE0) /* dss_data17.dss_data17 */ - - OMAP3_CORE1_IOPAD(0x2100, PIN_OUTPUT_PULLDOWN | PIN_OFF_OUTPUT_LOW | MUX_MODE3) /* dss_data18.dss_data0 */ - OMAP3_CORE1_IOPAD(0x2102, PIN_OUTPUT_PULLDOWN | PIN_OFF_OUTPUT_LOW | MUX_MODE3) /* dss_data19.dss_data1 */ - OMAP3_CORE1_IOPAD(0x2104, PIN_OUTPUT_PULLDOWN | PIN_OFF_OUTPUT_LOW | MUX_MODE3) /* dss_data20.dss_data2 */ - OMAP3_CORE1_IOPAD(0x2106, PIN_OUTPUT_PULLDOWN | PIN_OFF_OUTPUT_LOW | MUX_MODE3) /* dss_data21.dss_data3 */ - OMAP3_CORE1_IOPAD(0x2108, PIN_OUTPUT_PULLDOWN | PIN_OFF_OUTPUT_LOW | MUX_MODE3) /* dss_data22.dss_data4 */ - OMAP3_CORE1_IOPAD(0x210a, PIN_OUTPUT_PULLDOWN | PIN_OFF_OUTPUT_LOW | MUX_MODE3) /* dss_data23.dss_data5 */ + OMAP3_CORE1_IOPAD(0x2164, PIN_INPUT_PULLUP | MUX_MODE3) /* sdmmc2_dat4.sdmmc3_dat0 */ + OMAP3_CORE1_IOPAD(0x2166, PIN_INPUT_PULLUP | MUX_MODE3) /* sdmmc2_dat5.sdmmc3_dat1 */ + OMAP3_CORE1_IOPAD(0x2168, PIN_INPUT_PULLUP | MUX_MODE3) /* sdmmc2_dat6.sdmmc3_dat2 */ + OMAP3_CORE1_IOPAD(0x216a, PIN_INPUT_PULLUP | MUX_MODE3) /* sdmmc2_dat6.sdmmc3_dat3 */ + OMAP3_CORE1_IOPAD(0x2184, PIN_INPUT_PULLUP | MUX_MODE4) /* mcbsp4_clkx.gpio_152 */ + OMAP3_CORE1_IOPAD(0x218e, PIN_OUTPUT | MUX_MODE4) /* mcbsp1_fsr.gpio_157 */ >; }; }; -&omap3_pmx_wkup { - gpio_key_pins_wkup: pinmux_gpio_key_pins_wkup { - pinctrl-single,pins = < - OMAP3_WKUP_IOPAD(0x2a0a, PIN_INPUT_PULLUP | MUX_MODE4) /* sys_boot0.gpio_2 */ - OMAP3_WKUP_IOPAD(0x2a14, PIN_INPUT_PULLUP | MUX_MODE4) /* sys_boot5.gpio_7 */ - >; - }; - - lan9221_pins: pinmux_lan9221_pins { - pinctrl-single,pins = < - OMAP3_WKUP_IOPAD(0x2a5a, PIN_INPUT | MUX_MODE4) /* reserved.gpio_129 */ - >; - }; - - mmc1_cd: pinmux_mmc1_cd { +&omap3_pmx_core2 { + mmc3_core2_pins: pinmux_mmc3_core2_pins { pinctrl-single,pins = < - OMAP3_WKUP_IOPAD(0x2a54, PIN_INPUT_PULLUP | MUX_MODE4) /* reserved.gpio_127 */ + OMAP3630_CORE2_IOPAD(0x25d8, PIN_INPUT_PULLUP | MUX_MODE2) /* etk_clk.sdmmc3_clk */ + OMAP3630_CORE2_IOPAD(0x25da, PIN_INPUT_PULLUP | MUX_MODE2) /* etk_ctl.sdmmc3_cmd */ >; }; }; - -&i2c2 { - mt9p031@48 { - compatible = "aptina,mt9p031"; - reg = <0x48>; - clocks = <&isp 0>; - vaa-supply = <&vaux4>; - vdd-supply = <&vaux4>; - vdd_io-supply = <&vaux4>; - port { - mt9p031_out: endpoint { - input-clock-frequency = <24000000>; - pixel-clock-frequency = <72000000>; - remote-endpoint = <&ccdc_ep>; - }; - }; - }; -}; - -&i2c3 { - touchscreen: tsc2004@48 { - compatible = "ti,tsc2004"; - reg = <0x48>; - vio-supply = <&vaux1>; - pinctrl-names = "default"; - pinctrl-0 = <&tsc2004_pins>; - interrupts-extended = <&gpio5 25 IRQ_TYPE_EDGE_RISING>; /* gpio 153 */ - - touchscreen-fuzz-x = <4>; - touchscreen-fuzz-y = <7>; - touchscreen-fuzz-pressure = <2>; - touchscreen-size-x = <4096>; - touchscreen-size-y = <4096>; - touchscreen-max-pressure = <2048>; - - ti,x-plate-ohms = <280>; - ti,esd-recovery-timeout-ms = <8000>; - }; -}; - -&mcspi1 { - at25@0 { - compatible = "atmel,at25"; - reg = <0>; - spi-max-frequency = <5000000>; - spi-cpha; - spi-cpol; - - pagesize = <64>; - size = <32768>; - address-width = <16>; - }; -}; - -&isp { - pinctrl-names = "default"; - pinctrl-0 = <&isp_pins>; - ports { - port@0 { - reg = <0>; - ccdc_ep: endpoint { - remote-endpoint = <&mt9p031_out>; - bus-width = <8>; - hsync-active = <1>; - vsync-active = <1>; - pclk-sample = <0>; - }; - }; - }; -}; - -&uart1 { - interrupts-extended = <&intc 72 &omap3_pmx_core OMAP3_UART1_RX>; -}; - -/* Wired to the tps65950 on the SOM, only the USB connector is on the devkit */ -&usb_otg_hs { - pinctrl-names = "default"; - pinctrl-0 = <&hsusb_otg_pins>; - interface-type = <0>; - usb-phy = <&usb2_phy>; - phys = <&usb2_phy>; - phy-names = "usb2-phy"; - mode = <3>; - power = <50>; -}; diff --git a/arch/arm/boot/dts/logicpd-torpedo-baseboard.dtsi b/arch/arm/boot/dts/logicpd-torpedo-baseboard.dtsi new file mode 100644 index 000000000000..86c5644f558c --- /dev/null +++ b/arch/arm/boot/dts/logicpd-torpedo-baseboard.dtsi @@ -0,0 +1,395 @@ +/* + * This program is free software; you can redistribute it and/or modify + * it under the terms of the GNU General Public License version 2 as + * published by the Free Software Foundation. + */ + +/ { + gpio_keys { + compatible = "gpio-keys"; + pinctrl-names = "default"; + pinctrl-0 = <&gpio_key_pins &gpio_key_pins_wkup>; + + sysboot2 { + label = "sysboot2"; + gpios = <&gpio1 2 GPIO_ACTIVE_LOW>; /* gpio2 */ + linux,code = <BTN_0>; + wakeup-source; + }; + + sysboot5 { + label = "sysboot5"; + gpios = <&gpio1 7 GPIO_ACTIVE_LOW>; /* gpio7 */ + linux,code = <BTN_1>; + wakeup-source; + }; + + gpio1 { + label = "gpio1"; + gpios = <&gpio6 21 GPIO_ACTIVE_LOW>; /* gpio181 */ + linux,code = <BTN_2>; + wakeup-source; + }; + + gpio2 { + label = "gpio2"; + gpios = <&gpio6 18 GPIO_ACTIVE_LOW>; /* gpio178 */ + linux,code = <BTN_3>; + wakeup-source; + }; + }; + + sound { + compatible = "ti,omap-twl4030"; + ti,model = "omap3logic"; + ti,mcbsp = <&mcbsp2>; + }; + + leds { + compatible = "gpio-leds"; + pinctrl-names = "default"; + pinctrl-0 = <&led_pins>; + + led1 { + label = "led1"; + gpios = <&gpio6 20 GPIO_ACTIVE_HIGH>; /* gpio180 */ + linux,default-trigger = "cpu0"; + }; + + led2 { + label = "led2"; + gpios = <&gpio6 19 GPIO_ACTIVE_HIGH>; /* gpio179 */ + linux,default-trigger = "none"; + }; + }; + + pwm10: dmtimer-pwm { + compatible = "ti,omap-dmtimer-pwm"; + pinctrl-names = "default"; + pinctrl-0 = <&pwm_pins>; + ti,timers = <&timer10>; + #pwm-cells = <3>; + }; + +}; + +&vaux1 { + regulator-min-microvolt = <3000000>; + regulator-max-microvolt = <3000000>; +}; + +&vaux4 { + regulator-min-microvolt = <1800000>; + regulator-max-microvolt = <1800000>; +}; + +&mcbsp2 { + status = "okay"; +}; + +&charger { + ti,bb-uvolt = <3200000>; + ti,bb-uamp = <150>; +}; + +&gpmc { + ranges = <0 0 0x30000000 0x1000000 /* CS0: 16MB for NAND */ + 1 0 0x2c000000 0x1000000>; /* CS1: 16MB for LAN9221 */ + + ethernet@gpmc { + pinctrl-names = "default"; + pinctrl-0 = <&lan9221_pins>; + interrupt-parent = <&gpio5>; + interrupts = <1 IRQ_TYPE_LEVEL_LOW>; /* gpio129 */ + reg = <1 0 0xff>; + }; +}; + +&vpll2 { + regulator-always-on; +}; + +&dss { + status = "ok"; + vdds_dsi-supply = <&vpll2>; + vdda_video-supply = <&video_reg>; + pinctrl-names = "default"; + pinctrl-0 = <&dss_dpi_pins1>; + port { + dpi_out: endpoint { + remote-endpoint = <&lcd_in>; + data-lines = <16>; + }; + }; +}; + +/ { + aliases { + display0 = &lcd0; + }; + + video_reg: video_reg { + pinctrl-names = "default"; + pinctrl-0 = <&panel_pwr_pins>; + compatible = "regulator-fixed"; + regulator-name = "fixed-supply"; + regulator-min-microvolt = <3300000>; + regulator-max-microvolt = <3300000>; + gpio = <&gpio5 27 GPIO_ACTIVE_HIGH>; /* gpio155, lcd INI */ + }; + + lcd0: display { + compatible = "panel-dpi"; + label = "15"; + status = "okay"; + /* default-on; */ + pinctrl-names = "default"; + + port { + lcd_in: endpoint { + remote-endpoint = <&dpi_out>; + }; + }; + + panel-timing { + clock-frequency = <9000000>; + hactive = <480>; + vactive = <272>; + hfront-porch = <3>; + hback-porch = <2>; + hsync-len = <42>; + vback-porch = <3>; + vfront-porch = <4>; + vsync-len = <11>; + hsync-active = <0>; + vsync-active = <0>; + de-active = <1>; + pixelclk-active = <1>; + }; + }; + + bl: backlight { + compatible = "pwm-backlight"; + pinctrl-names = "default"; + pinctrl-0 = <&backlight_pins>; + pwms = <&pwm10 0 5000000 0>; + brightness-levels = <0 10 20 30 40 50 60 70 80 90 100>; + default-brightness-level = <7>; + enable-gpios = <&gpio5 26 GPIO_ACTIVE_HIGH>; /* gpio_154 */ + }; +}; + +&mmc1 { + interrupts-extended = <&intc 83 &omap3_pmx_core 0x11a>; + pinctrl-names = "default"; + pinctrl-0 = <&mmc1_pins &mmc1_cd>; + cd-gpios = <&gpio4 31 GPIO_ACTIVE_LOW>; /* gpio127 */ + vmmc-supply = <&vmmc1>; + bus-width = <4>; + cap-power-off-card; +}; + +&omap3_pmx_core { + gpio_key_pins: pinmux_gpio_key_pins { + pinctrl-single,pins = < + OMAP3_CORE1_IOPAD(0x21d6, PIN_INPUT_PULLUP | MUX_MODE4) /* mcspi2_clk.gpio_178 */ + OMAP3_CORE1_IOPAD(0x21dc, PIN_INPUT_PULLUP | MUX_MODE4) /* mcspi2_cs0.gpio_181 */ + >; + }; + + pwm_pins: pinmux_pwm_pins { + pinctrl-single,pins = < + OMAP3_CORE1_IOPAD(0x20B8, PIN_OUTPUT | PIN_OFF_OUTPUT_LOW | MUX_MODE3) /* gpmc_ncs5.gpt_10_pwm_evt */ + >; + }; + + led_pins: pinmux_led_pins { + pinctrl-single,pins = < + OMAP3_CORE1_IOPAD(0x21d8, PIN_OUTPUT | MUX_MODE4) /* gpio_179 */ + OMAP3_CORE1_IOPAD(0x21da, PIN_OUTPUT | MUX_MODE4) /* gpio_180 */ + >; + }; + + mmc1_pins: pinmux_mmc1_pins { + pinctrl-single,pins = < + OMAP3_CORE1_IOPAD(0x2144, PIN_OUTPUT | MUX_MODE0) /* sdmmc1_clk.sdmmc1_clk */ + OMAP3_CORE1_IOPAD(0x2146, PIN_INPUT | MUX_MODE0) /* sdmmc1_cmd.sdmmc1_cmd */ + OMAP3_CORE1_IOPAD(0x2148, PIN_INPUT | MUX_MODE0) /* sdmmc1_dat0.sdmmc1_dat0 */ + OMAP3_CORE1_IOPAD(0x214a, PIN_INPUT | MUX_MODE0) /* sdmmc1_dat1.sdmmc1_dat1 */ + OMAP3_CORE1_IOPAD(0x214c, PIN_INPUT | MUX_MODE0) /* sdmmc1_dat2.sdmmc1_dat2 */ + OMAP3_CORE1_IOPAD(0x214e, PIN_INPUT | MUX_MODE0) /* sdmmc1_dat3.sdmmc1_dat3 */ + >; + }; + + tsc2004_pins: pinmux_tsc2004_pins { + pinctrl-single,pins = < + OMAP3_CORE1_IOPAD(0x2186, PIN_INPUT | MUX_MODE4) /* mcbsp4_dr.gpio_153 */ + >; + }; + + backlight_pins: pinmux_backlight_pins { + pinctrl-single,pins = < + OMAP3_CORE1_IOPAD(0x2188, PIN_OUTPUT | PIN_OFF_OUTPUT_LOW | MUX_MODE4) /* mcbsp4_dx.gpio_154 */ + >; + }; + + isp_pins: pinmux_isp_pins { + pinctrl-single,pins = < + OMAP3_CORE1_IOPAD(0x210c, PIN_INPUT | MUX_MODE0) /* cam_hs.cam_hs */ + OMAP3_CORE1_IOPAD(0x210e, PIN_INPUT | MUX_MODE0) /* cam_vs.cam_vs */ + OMAP3_CORE1_IOPAD(0x2110, PIN_INPUT | MUX_MODE0) /* cam_xclka.cam_xclka */ + OMAP3_CORE1_IOPAD(0x2112, PIN_INPUT | MUX_MODE0) /* cam_pclk.cam_pclk */ + + OMAP3_CORE1_IOPAD(0x2116, PIN_INPUT | MUX_MODE0) /* cam_d0.cam_d0 */ + OMAP3_CORE1_IOPAD(0x2118, PIN_INPUT | MUX_MODE0) /* cam_d1.cam_d1 */ + OMAP3_CORE1_IOPAD(0x211a, PIN_INPUT | MUX_MODE0) /* cam_d2.cam_d2 */ + OMAP3_CORE1_IOPAD(0x211c, PIN_INPUT | MUX_MODE0) /* cam_d3.cam_d3 */ + OMAP3_CORE1_IOPAD(0x211e, PIN_INPUT | MUX_MODE0) /* cam_d4.cam_d4 */ + OMAP3_CORE1_IOPAD(0x2120, PIN_INPUT | MUX_MODE0) /* cam_d5.cam_d5 */ + OMAP3_CORE1_IOPAD(0x2122, PIN_INPUT | MUX_MODE0) /* cam_d6.cam_d6 */ + OMAP3_CORE1_IOPAD(0x2124, PIN_INPUT | MUX_MODE0) /* cam_d7.cam_d7 */ + >; + }; + + panel_pwr_pins: pinmux_panel_pwr_pins { + pinctrl-single,pins = < + OMAP3_CORE1_IOPAD(0x218a, PIN_OUTPUT | PIN_OFF_OUTPUT_LOW | MUX_MODE4) /* mcbsp4_fs.gpio_155 */ + >; + }; + + dss_dpi_pins1: pinmux_dss_dpi_pins1 { + pinctrl-single,pins = < + OMAP3_CORE1_IOPAD(0x20d4, PIN_OUTPUT_PULLDOWN | PIN_OFF_OUTPUT_LOW | MUX_MODE0) /* dss_pclk.dss_pclk */ + OMAP3_CORE1_IOPAD(0x20d6, PIN_OUTPUT_PULLDOWN | PIN_OFF_OUTPUT_LOW | MUX_MODE0) /* dss_hsync.dss_hsync */ + OMAP3_CORE1_IOPAD(0x20d8, PIN_OUTPUT_PULLDOWN | PIN_OFF_OUTPUT_LOW | MUX_MODE0) /* dss_vsync.dss_vsync */ + OMAP3_CORE1_IOPAD(0x20da, PIN_OUTPUT_PULLDOWN | PIN_OFF_OUTPUT_LOW | MUX_MODE0) /* dss_acbias.dss_acbias */ + + OMAP3_CORE1_IOPAD(0x20e8, PIN_OUTPUT_PULLDOWN | PIN_OFF_OUTPUT_LOW | MUX_MODE0) /* dss_data6.dss_data6 */ + OMAP3_CORE1_IOPAD(0x20ea, PIN_OUTPUT_PULLDOWN | PIN_OFF_OUTPUT_LOW | MUX_MODE0) /* dss_data7.dss_data7 */ + OMAP3_CORE1_IOPAD(0x20ec, PIN_OUTPUT_PULLDOWN | PIN_OFF_OUTPUT_LOW | MUX_MODE0) /* dss_data8.dss_data8 */ + OMAP3_CORE1_IOPAD(0x20ee, PIN_OUTPUT_PULLDOWN | PIN_OFF_OUTPUT_LOW | MUX_MODE0) /* dss_data9.dss_data9 */ + OMAP3_CORE1_IOPAD(0x20f0, PIN_OUTPUT_PULLDOWN | PIN_OFF_OUTPUT_LOW | MUX_MODE0) /* dss_data10.dss_data10 */ + OMAP3_CORE1_IOPAD(0x20f2, PIN_OUTPUT_PULLDOWN | PIN_OFF_OUTPUT_LOW | MUX_MODE0) /* dss_data11.dss_data11 */ + OMAP3_CORE1_IOPAD(0x20f4, PIN_OUTPUT_PULLDOWN | PIN_OFF_OUTPUT_LOW | MUX_MODE0) /* dss_data12.dss_data12 */ + OMAP3_CORE1_IOPAD(0x20f6, PIN_OUTPUT_PULLDOWN | PIN_OFF_OUTPUT_LOW | MUX_MODE0) /* dss_data13.dss_data13 */ + OMAP3_CORE1_IOPAD(0x20f8, PIN_OUTPUT_PULLDOWN | PIN_OFF_OUTPUT_LOW | MUX_MODE0) /* dss_data14.dss_data14 */ + OMAP3_CORE1_IOPAD(0x20fa, PIN_OUTPUT_PULLDOWN | PIN_OFF_OUTPUT_LOW | MUX_MODE0) /* dss_data15.dss_data15 */ + OMAP3_CORE1_IOPAD(0x20fc, PIN_OUTPUT_PULLDOWN | PIN_OFF_OUTPUT_LOW | MUX_MODE0) /* dss_data16.dss_data16 */ + OMAP3_CORE1_IOPAD(0x20fe, PIN_OUTPUT_PULLDOWN | PIN_OFF_OUTPUT_LOW | MUX_MODE0) /* dss_data17.dss_data17 */ + + OMAP3_CORE1_IOPAD(0x2100, PIN_OUTPUT_PULLDOWN | PIN_OFF_OUTPUT_LOW | MUX_MODE3) /* dss_data18.dss_data0 */ + OMAP3_CORE1_IOPAD(0x2102, PIN_OUTPUT_PULLDOWN | PIN_OFF_OUTPUT_LOW | MUX_MODE3) /* dss_data19.dss_data1 */ + OMAP3_CORE1_IOPAD(0x2104, PIN_OUTPUT_PULLDOWN | PIN_OFF_OUTPUT_LOW | MUX_MODE3) /* dss_data20.dss_data2 */ + OMAP3_CORE1_IOPAD(0x2106, PIN_OUTPUT_PULLDOWN | PIN_OFF_OUTPUT_LOW | MUX_MODE3) /* dss_data21.dss_data3 */ + OMAP3_CORE1_IOPAD(0x2108, PIN_OUTPUT_PULLDOWN | PIN_OFF_OUTPUT_LOW | MUX_MODE3) /* dss_data22.dss_data4 */ + OMAP3_CORE1_IOPAD(0x210a, PIN_OUTPUT_PULLDOWN | PIN_OFF_OUTPUT_LOW | MUX_MODE3) /* dss_data23.dss_data5 */ + >; + }; +}; + +&omap3_pmx_wkup { + gpio_key_pins_wkup: pinmux_gpio_key_pins_wkup { + pinctrl-single,pins = < + OMAP3_WKUP_IOPAD(0x2a0a, PIN_INPUT_PULLUP | MUX_MODE4) /* sys_boot0.gpio_2 */ + OMAP3_WKUP_IOPAD(0x2a14, PIN_INPUT_PULLUP | MUX_MODE4) /* sys_boot5.gpio_7 */ + >; + }; + + lan9221_pins: pinmux_lan9221_pins { + pinctrl-single,pins = < + OMAP3_WKUP_IOPAD(0x2a5a, PIN_INPUT | MUX_MODE4) /* reserved.gpio_129 */ + >; + }; + + mmc1_cd: pinmux_mmc1_cd { + pinctrl-single,pins = < + OMAP3_WKUP_IOPAD(0x2a54, PIN_INPUT_PULLUP | MUX_MODE4) /* reserved.gpio_127 */ + >; + }; +}; + +&i2c2 { + mt9p031@48 { + compatible = "aptina,mt9p031"; + reg = <0x48>; + clocks = <&isp 0>; + vaa-supply = <&vaux4>; + vdd-supply = <&vaux4>; + vdd_io-supply = <&vaux4>; + port { + mt9p031_out: endpoint { + input-clock-frequency = <24000000>; + pixel-clock-frequency = <72000000>; + remote-endpoint = <&ccdc_ep>; + }; + }; + }; +}; + +&i2c3 { + touchscreen: tsc2004@48 { + compatible = "ti,tsc2004"; + reg = <0x48>; + vio-supply = <&vaux1>; + pinctrl-names = "default"; + pinctrl-0 = <&tsc2004_pins>; + interrupts-extended = <&gpio5 25 IRQ_TYPE_EDGE_RISING>; /* gpio 153 */ + + touchscreen-fuzz-x = <4>; + touchscreen-fuzz-y = <7>; + touchscreen-fuzz-pressure = <2>; + touchscreen-size-x = <4096>; + touchscreen-size-y = <4096>; + touchscreen-max-pressure = <2048>; + + ti,x-plate-ohms = <280>; + ti,esd-recovery-timeout-ms = <8000>; + }; +}; + +&mcspi1 { + at25@0 { + compatible = "atmel,at25"; + reg = <0>; + spi-max-frequency = <5000000>; + spi-cpha; + spi-cpol; + + pagesize = <64>; + size = <32768>; + address-width = <16>; + }; +}; + +&isp { + pinctrl-names = "default"; + pinctrl-0 = <&isp_pins>; + ports { + port@0 { + reg = <0>; + ccdc_ep: endpoint { + remote-endpoint = <&mt9p031_out>; + bus-width = <8>; + hsync-active = <1>; + vsync-active = <1>; + pclk-sample = <0>; + }; + }; + }; +}; + +&uart1 { + interrupts-extended = <&intc 72 &omap3_pmx_core OMAP3_UART1_RX>; +}; + +/* Wired to the tps65950 on the SOM, only the USB connector is on the devkit */ +&usb_otg_hs { + pinctrl-names = "default"; + pinctrl-0 = <&hsusb_otg_pins>; + interface-type = <0>; + usb-phy = <&usb2_phy>; + phys = <&usb2_phy>; + phy-names = "usb2-phy"; + mode = <3>; + power = <50>; +}; diff --git a/arch/arm/boot/dts/logicpd-torpedo-som.dtsi b/arch/arm/boot/dts/logicpd-torpedo-som.dtsi index 6d89736c7b44..b50b796e15c7 100644 --- a/arch/arm/boot/dts/logicpd-torpedo-som.dtsi +++ b/arch/arm/boot/dts/logicpd-torpedo-som.dtsi @@ -30,17 +30,6 @@ linux,default-trigger = "none"; }; }; - - wl12xx_vmmc: wl12xx_vmmc { - compatible = "regulator-fixed"; - regulator-name = "vwl1271"; - regulator-min-microvolt = <1800000>; - regulator-max-microvolt = <1800000>; - gpio = <&gpio5 29 0>; /* gpio157 */ - startup-delay-us = <70000>; - enable-active-high; - vin-supply = <&vmmc2>; - }; }; &gpmc { @@ -73,33 +62,6 @@ gpmc,device-width = <2>; #address-cells = <1>; #size-cells = <1>; - - /* u-boot uses mtdparts=omap2-nand.0:512k(x-loader),1920k(u-boot),128k(u-boot-env),4m(kernel),-(fs) */ - - x-loader@0 { - label = "x-loader"; - reg = <0 0x80000>; - }; - - bootloaders@80000 { - label = "u-boot"; - reg = <0x80000 0x1e0000>; - }; - - bootloaders_env@260000 { - label = "u-boot-env"; - reg = <0x260000 0x20000>; - }; - - kernel@280000 { - label = "kernel"; - reg = <0x280000 0x400000>; - }; - - filesystem@680000 { - label = "fs"; - reg = <0x680000 0>; /* 0 = MTDPART_SIZ_FULL */ - }; }; }; @@ -131,44 +93,7 @@ }; }; -/* - * Only found on the wireless SOM. For the SOM without wireless, the pins for - * MMC3 can be routed with jumpers to the second MMC slot on the devkit and - * gpio157 is not connected. So this should be OK to keep common for now, - * probably device tree overlays is the way to go with the various SOM and - * jumpering combinations for the long run. - */ -&mmc3 { - interrupts-extended = <&intc 94 &omap3_pmx_core2 0x46>; - pinctrl-0 = <&mmc3_pins &mmc3_core2_pins>; - pinctrl-names = "default"; - vmmc-supply = <&wl12xx_vmmc>; - non-removable; - bus-width = <4>; - cap-power-off-card; - #address-cells = <1>; - #size-cells = <0>; - wlcore: wlcore@2 { - compatible = "ti,wl1283"; - reg = <2>; - interrupt-parent = <&gpio5>; - interrupts = <24 IRQ_TYPE_LEVEL_HIGH>; /* gpio 152 */ - ref-clock-frequency = <26000000>; - tcxo-clock-frequency = <26000000>; - }; -}; - &omap3_pmx_core { - mmc3_pins: pinmux_mm3_pins { - pinctrl-single,pins = < - OMAP3_CORE1_IOPAD(0x2164, PIN_INPUT_PULLUP | MUX_MODE3) /* sdmmc2_dat4.sdmmc3_dat0 */ - OMAP3_CORE1_IOPAD(0x2166, PIN_INPUT_PULLUP | MUX_MODE3) /* sdmmc2_dat5.sdmmc3_dat1 */ - OMAP3_CORE1_IOPAD(0x2168, PIN_INPUT_PULLUP | MUX_MODE3) /* sdmmc2_dat6.sdmmc3_dat2 */ - OMAP3_CORE1_IOPAD(0x216a, PIN_INPUT_PULLUP | MUX_MODE3) /* sdmmc2_dat6.sdmmc3_dat3 */ - OMAP3_CORE1_IOPAD(0x2184, PIN_INPUT_PULLUP | MUX_MODE4) /* mcbsp4_clkx.gpio_152 */ - OMAP3_CORE1_IOPAD(0x218e, PIN_OUTPUT | MUX_MODE4) /* mcbsp1_fsr.gpio_157 */ - >; - }; mcbsp2_pins: pinmux_mcbsp2_pins { pinctrl-single,pins = < OMAP3_CORE1_IOPAD(0x213c, PIN_INPUT | MUX_MODE0) /* mcbsp2_fsx */ @@ -224,15 +149,6 @@ pinctrl-0 = <&mcspi1_pins>; }; -&omap3_pmx_core2 { - mmc3_core2_pins: pinmux_mmc3_core2_pins { - pinctrl-single,pins = < - OMAP3630_CORE2_IOPAD(0x25d8, PIN_INPUT_PULLUP | MUX_MODE2) /* etk_clk.sdmmc3_clk */ - OMAP3630_CORE2_IOPAD(0x25da, PIN_INPUT_PULLUP | MUX_MODE2) /* etk_ctl.sdmmc3_cmd */ - >; - }; -}; - #include "twl4030.dtsi" #include "twl4030_omap3.dtsi" diff --git a/arch/arm/boot/dts/omap3-n900.dts b/arch/arm/boot/dts/omap3-n900.dts index 669c51c00c00..5362139d5312 100644 --- a/arch/arm/boot/dts/omap3-n900.dts +++ b/arch/arm/boot/dts/omap3-n900.dts @@ -558,7 +558,7 @@ tlv320aic3x: tlv320aic3x@18 { compatible = "ti,tlv320aic3x"; reg = <0x18>; - gpio-reset = <&gpio2 28 GPIO_ACTIVE_HIGH>; /* 60 */ + reset-gpios = <&gpio2 28 GPIO_ACTIVE_LOW>; /* 60 */ ai3x-gpio-func = < 0 /* AIC3X_GPIO1_FUNC_DISABLED */ 5 /* AIC3X_GPIO2_FUNC_DIGITAL_MIC_INPUT */ @@ -575,7 +575,7 @@ tlv320aic3x_aux: tlv320aic3x@19 { compatible = "ti,tlv320aic3x"; reg = <0x19>; - gpio-reset = <&gpio2 28 GPIO_ACTIVE_HIGH>; /* 60 */ + reset-gpios = <&gpio2 28 GPIO_ACTIVE_LOW>; /* 60 */ AVDD-supply = <&vmmc2>; DRVDD-supply = <&vmmc2>; |