mfd/power: ab8500: Push data to power supply code

There is a slew of defines, structs and enums and even a
function call only relevant for the charging code that
still lives in <linux/mfd/abx500.h>. Push it down to the
"ab8500-bm.h" header in the power supply subsystem where
it is actually used.

Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Acked-by: Sebastian Reichel <sebastian.reichel@collabora.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>

1 files changed, 0 insertions, 276 deletions

diff --git a/include/linux/mfd/abx500.h b/include/linux/mfd/abx500.h
index 23040b6f1615..7f07cfe44753 100644
--- a/include/linux/mfd/abx500.h
+++ b/include/linux/mfd/abx500.h
@@ -28,282 +28,6 @@ struct abx500_init_settings {
 	u8 setting;
 };
 
-/* Battery driver related data */
-/*
- * ADC for the battery thermistor.
- * When using the ABx500_ADC_THERM_BATCTRL the battery ID resistor is combined
- * with a NTC resistor to both identify the battery and to measure its
- * temperature. Different phone manufactures uses different techniques to both
- * identify the battery and to read its temperature.
- */
-enum abx500_adc_therm {
-	ABx500_ADC_THERM_BATCTRL,
-	ABx500_ADC_THERM_BATTEMP,
-};
-
-/**
- * struct abx500_res_to_temp - defines one point in a temp to res curve. To
- * be used in battery packs that combines the identification resistor with a
- * NTC resistor.
- * @temp:			battery pack temperature in Celsius
- * @resist:			NTC resistor net total resistance
- */
-struct abx500_res_to_temp {
-	int temp;
-	int resist;
-};
-
-/**
- * struct abx500_v_to_cap - Table for translating voltage to capacity
- * @voltage:		Voltage in mV
- * @capacity:		Capacity in percent
- */
-struct abx500_v_to_cap {
-	int voltage;
-	int capacity;
-};
-
-/* Forward declaration */
-struct abx500_fg;
-
-/**
- * struct abx500_fg_parameters - Fuel gauge algorithm parameters, in seconds
- * if not specified
- * @recovery_sleep_timer:	Time between measurements while recovering
- * @recovery_total_time:	Total recovery time
- * @init_timer:			Measurement interval during startup
- * @init_discard_time:		Time we discard voltage measurement at startup
- * @init_total_time:		Total init time during startup
- * @high_curr_time:		Time current has to be high to go to recovery
- * @accu_charging:		FG accumulation time while charging
- * @accu_high_curr:		FG accumulation time in high current mode
- * @high_curr_threshold:	High current threshold, in mA
- * @lowbat_threshold:		Low battery threshold, in mV
- * @overbat_threshold:		Over battery threshold, in mV
- * @battok_falling_th_sel0	Threshold in mV for battOk signal sel0
- *				Resolution in 50 mV step.
- * @battok_raising_th_sel1	Threshold in mV for battOk signal sel1
- *				Resolution in 50 mV step.
- * @user_cap_limit		Capacity reported from user must be within this
- *				limit to be considered as sane, in percentage
- *				points.
- * @maint_thres			This is the threshold where we stop reporting
- *				battery full while in maintenance, in per cent
- * @pcut_enable:			Enable power cut feature in ab8505
- * @pcut_max_time:		Max time threshold
- * @pcut_flag_time:		Flagtime threshold
- * @pcut_max_restart:		Max number of restarts
- * @pcut_debounce_time:		Sets battery debounce time
- */
-struct abx500_fg_parameters {
-	int recovery_sleep_timer;
-	int recovery_total_time;
-	int init_timer;
-	int init_discard_time;
-	int init_total_time;
-	int high_curr_time;
-	int accu_charging;
-	int accu_high_curr;
-	int high_curr_threshold;
-	int lowbat_threshold;
-	int overbat_threshold;
-	int battok_falling_th_sel0;
-	int battok_raising_th_sel1;
-	int user_cap_limit;
-	int maint_thres;
-	bool pcut_enable;
-	u8 pcut_max_time;
-	u8 pcut_flag_time;
-	u8 pcut_max_restart;
-	u8 pcut_debounce_time;
-};
-
-/**
- * struct abx500_charger_maximization - struct used by the board config.
- * @use_maxi:		Enable maximization for this battery type
- * @maxi_chg_curr:	Maximum charger current allowed
- * @maxi_wait_cycles:	cycles to wait before setting charger current
- * @charger_curr_step	delta between two charger current settings (mA)
- */
-struct abx500_maxim_parameters {
-	bool ena_maxi;
-	int chg_curr;
-	int wait_cycles;
-	int charger_curr_step;
-};
-
-/**
- * struct abx500_battery_type - different batteries supported
- * @name:			battery technology
- * @resis_high:			battery upper resistance limit
- * @resis_low:			battery lower resistance limit
- * @charge_full_design:		Maximum battery capacity in mAh
- * @nominal_voltage:		Nominal voltage of the battery in mV
- * @termination_vol:		max voltage upto which battery can be charged
- * @termination_curr		battery charging termination current in mA
- * @recharge_cap		battery capacity limit that will trigger a new
- *				full charging cycle in the case where maintenan-
- *				-ce charging has been disabled
- * @normal_cur_lvl:		charger current in normal state in mA
- * @normal_vol_lvl:		charger voltage in normal state in mV
- * @maint_a_cur_lvl:		charger current in maintenance A state in mA
- * @maint_a_vol_lvl:		charger voltage in maintenance A state in mV
- * @maint_a_chg_timer_h:	charge time in maintenance A state
- * @maint_b_cur_lvl:		charger current in maintenance B state in mA
- * @maint_b_vol_lvl:		charger voltage in maintenance B state in mV
- * @maint_b_chg_timer_h:	charge time in maintenance B state
- * @low_high_cur_lvl:		charger current in temp low/high state in mA
- * @low_high_vol_lvl:		charger voltage in temp low/high state in mV'
- * @battery_resistance:		battery inner resistance in mOhm.
- * @n_r_t_tbl_elements:		number of elements in r_to_t_tbl
- * @r_to_t_tbl:			table containing resistance to temp points
- * @n_v_cap_tbl_elements:	number of elements in v_to_cap_tbl
- * @v_to_cap_tbl:		Voltage to capacity (in %) table
- * @n_batres_tbl_elements	number of elements in the batres_tbl
- * @batres_tbl			battery internal resistance vs temperature table
- */
-struct abx500_battery_type {
-	int name;
-	int resis_high;
-	int resis_low;
-	int charge_full_design;
-	int nominal_voltage;
-	int termination_vol;
-	int termination_curr;
-	int recharge_cap;
-	int normal_cur_lvl;
-	int normal_vol_lvl;
-	int maint_a_cur_lvl;
-	int maint_a_vol_lvl;
-	int maint_a_chg_timer_h;
-	int maint_b_cur_lvl;
-	int maint_b_vol_lvl;
-	int maint_b_chg_timer_h;
-	int low_high_cur_lvl;
-	int low_high_vol_lvl;
-	int battery_resistance;
-	int n_temp_tbl_elements;
-	const struct abx500_res_to_temp *r_to_t_tbl;
-	int n_v_cap_tbl_elements;
-	const struct abx500_v_to_cap *v_to_cap_tbl;
-	int n_batres_tbl_elements;
-	const struct batres_vs_temp *batres_tbl;
-};
-
-/**
- * struct abx500_bm_capacity_levels - abx500 capacity level data
- * @critical:		critical capacity level in percent
- * @low:		low capacity level in percent
- * @normal:		normal capacity level in percent
- * @high:		high capacity level in percent
- * @full:		full capacity level in percent
- */
-struct abx500_bm_capacity_levels {
-	int critical;
-	int low;
-	int normal;
-	int high;
-	int full;
-};
-
-/**
- * struct abx500_bm_charger_parameters - Charger specific parameters
- * @usb_volt_max:	maximum allowed USB charger voltage in mV
- * @usb_curr_max:	maximum allowed USB charger current in mA
- * @ac_volt_max:	maximum allowed AC charger voltage in mV
- * @ac_curr_max:	maximum allowed AC charger current in mA
- */
-struct abx500_bm_charger_parameters {
-	int usb_volt_max;
-	int usb_curr_max;
-	int ac_volt_max;
-	int ac_curr_max;
-};
-
-/**
- * struct abx500_bm_data - abx500 battery management data
- * @temp_under		under this temp, charging is stopped
- * @temp_low		between this temp and temp_under charging is reduced
- * @temp_high		between this temp and temp_over charging is reduced
- * @temp_over		over this temp, charging is stopped
- * @temp_now		present battery temperature
- * @temp_interval_chg	temperature measurement interval in s when charging
- * @temp_interval_nochg	temperature measurement interval in s when not charging
- * @main_safety_tmr_h	safety timer for main charger
- * @usb_safety_tmr_h	safety timer for usb charger
- * @bkup_bat_v		voltage which we charge the backup battery with
- * @bkup_bat_i		current which we charge the backup battery with
- * @no_maintenance	indicates that maintenance charging is disabled
- * @capacity_scaling    indicates whether capacity scaling is to be used
- * @abx500_adc_therm	placement of thermistor, batctrl or battemp adc
- * @chg_unknown_bat	flag to enable charging of unknown batteries
- * @enable_overshoot	flag to enable VBAT overshoot control
- * @auto_trig		flag to enable auto adc trigger
- * @fg_res		resistance of FG resistor in 0.1mOhm
- * @n_btypes		number of elements in array bat_type
- * @batt_id		index of the identified battery in array bat_type
- * @interval_charging	charge alg cycle period time when charging (sec)
- * @interval_not_charging charge alg cycle period time when not charging (sec)
- * @temp_hysteresis	temperature hysteresis
- * @gnd_lift_resistance	Battery ground to phone ground resistance (mOhm)
- * @n_chg_out_curr		number of elements in array chg_output_curr
- * @n_chg_in_curr		number of elements in array chg_input_curr
- * @chg_output_curr	charger output current level map
- * @chg_input_curr		charger input current level map
- * @maxi		maximization parameters
- * @cap_levels		capacity in percent for the different capacity levels
- * @bat_type		table of supported battery types
- * @chg_params		charger parameters
- * @fg_params		fuel gauge parameters
- */
-struct abx500_bm_data {
-	int temp_under;
-	int temp_low;
-	int temp_high;
-	int temp_over;
-	int temp_now;
-	int temp_interval_chg;
-	int temp_interval_nochg;
-	int main_safety_tmr_h;
-	int usb_safety_tmr_h;
-	int bkup_bat_v;
-	int bkup_bat_i;
-	bool autopower_cfg;
-	bool ac_enabled;
-	bool usb_enabled;
-	bool no_maintenance;
-	bool capacity_scaling;
-	bool chg_unknown_bat;
-	bool enable_overshoot;
-	bool auto_trig;
-	enum abx500_adc_therm adc_therm;
-	int fg_res;
-	int n_btypes;
-	int batt_id;
-	int interval_charging;
-	int interval_not_charging;
-	int temp_hysteresis;
-	int gnd_lift_resistance;
-	int n_chg_out_curr;
-	int n_chg_in_curr;
-	int *chg_output_curr;
-	int *chg_input_curr;
-	const struct abx500_maxim_parameters *maxi;
-	const struct abx500_bm_capacity_levels *cap_levels;
-	struct abx500_battery_type *bat_type;
-	const struct abx500_bm_charger_parameters *chg_params;
-	const struct abx500_fg_parameters *fg_params;
-};
-
-enum {
-	NTC_EXTERNAL = 0,
-	NTC_INTERNAL,
-};
-
-int ab8500_bm_of_probe(struct device *dev,
-		       struct device_node *np,
-		       struct abx500_bm_data *bm);
-
 int abx500_set_register_interruptible(struct device *dev, u8 bank, u8 reg,
 	u8 value);
 int abx500_get_register_interruptible(struct device *dev, u8 bank, u8 reg,