Merge tag 'v4.0-rc5' into next

Merge with the latest upstream to synchronize Synaptics changes
and bring in new infrastructure pieces.

Conflicts:
	drivers/input/mouse/synaptics.c

1 files changed, 130 insertions, 403 deletions

diff --git a/drivers/usb/gadget/udc/net2280.c b/drivers/usb/gadget/udc/net2280.c
index d6411e0a8e03..d2c0bf65e345 100644
--- a/drivers/usb/gadget/udc/net2280.c
+++ b/drivers/usb/gadget/udc/net2280.c
@@ -12,11 +12,7 @@
  * the Mass Storage, Serial, and Ethernet/RNDIS gadget drivers
  * as well as Gadget Zero and Gadgetfs.
  *
- * DMA is enabled by default.  Drivers using transfer queues might use
- * DMA chaining to remove IRQ latencies between transfers.  (Except when
- * short OUT transfers happen.)  Drivers can use the req->no_interrupt
- * hint to completely eliminate some IRQs, if a later IRQ is guaranteed
- * and DMA chaining is enabled.
+ * DMA is enabled by default.
  *
  * MSI is enabled by default.  The legacy IRQ is used if MSI couldn't
  * be enabled.
@@ -84,23 +80,6 @@ static const char *const ep_name[] = {
 	"ep-e", "ep-f", "ep-g", "ep-h",
 };
 
-/* use_dma -- general goodness, fewer interrupts, less cpu load (vs PIO)
- * use_dma_chaining -- dma descriptor queueing gives even more irq reduction
- *
- * The net2280 DMA engines are not tightly integrated with their FIFOs;
- * not all cases are (yet) handled well in this driver or the silicon.
- * Some gadget drivers work better with the dma support here than others.
- * These two parameters let you use PIO or more aggressive DMA.
- */
-static bool use_dma = true;
-static bool use_dma_chaining;
-static bool use_msi = true;
-
-/* "modprobe net2280 use_dma=n" etc */
-module_param(use_dma, bool, 0444);
-module_param(use_dma_chaining, bool, 0444);
-module_param(use_msi, bool, 0444);
-
 /* mode 0 == ep-{a,b,c,d} 1K fifo each
  * mode 1 == ep-{a,b} 2K fifo each, ep-{c,d} unavailable
  * mode 2 == ep-a 2K fifo, ep-{b,c} 1K each, ep-d unavailable
@@ -120,11 +99,6 @@ static bool enable_suspend;
 /* "modprobe net2280 enable_suspend=1" etc */
 module_param(enable_suspend, bool, 0444);
 
-/* force full-speed operation */
-static bool full_speed;
-module_param(full_speed, bool, 0444);
-MODULE_PARM_DESC(full_speed, "force full-speed mode -- for testing only!");
-
 #define	DIR_STRING(bAddress) (((bAddress) & USB_DIR_IN) ? "in" : "out")
 
 static char *type_string(u8 bmAttributes)
@@ -202,15 +176,6 @@ net2280_enable(struct usb_ep *_ep, const struct usb_endpoint_descriptor *desc)
 	/* set speed-dependent max packet; may kick in high bandwidth */
 	set_max_speed(ep, max);
 
-	/* FIFO lines can't go to different packets.  PIO is ok, so
-	 * use it instead of troublesome (non-bulk) multi-packet DMA.
-	 */
-	if (ep->dma && (max % 4) != 0 && use_dma_chaining) {
-		ep_dbg(ep->dev, "%s, no dma for maxpacket %d\n",
-			ep->ep.name, ep->ep.maxpacket);
-		ep->dma = NULL;
-	}
-
 	/* set type, direction, address; reset fifo counters */
 	writel(BIT(FIFO_FLUSH), &ep->regs->ep_stat);
 	tmp = (desc->bmAttributes & USB_ENDPOINT_XFERTYPE_MASK);
@@ -478,7 +443,7 @@ static int net2280_disable(struct usb_ep *_ep)
 	/* synch memory views with the device */
 	(void)readl(&ep->cfg->ep_cfg);
 
-	if (use_dma && !ep->dma && ep->num >= 1 && ep->num <= 4)
+	if (!ep->dma && ep->num >= 1 && ep->num <= 4)
 		ep->dma = &ep->dev->dma[ep->num - 1];
 
 	spin_unlock_irqrestore(&ep->dev->lock, flags);
@@ -610,9 +575,15 @@ static void out_flush(struct net2280_ep *ep)
 	u32	__iomem *statp;
 	u32	tmp;
 
-	ASSERT_OUT_NAKING(ep);
-
 	statp = &ep->regs->ep_stat;
+
+	tmp = readl(statp);
+	if (tmp & BIT(NAK_OUT_PACKETS)) {
+		ep_dbg(ep->dev, "%s %s %08x !NAK\n",
+			ep->ep.name, __func__, tmp);
+		writel(BIT(SET_NAK_OUT_PACKETS), &ep->regs->ep_rsp);
+	}
+
 	writel(BIT(DATA_OUT_PING_TOKEN_INTERRUPT) |
 		BIT(DATA_PACKET_RECEIVED_INTERRUPT),
 		statp);
@@ -747,8 +718,7 @@ static void fill_dma_desc(struct net2280_ep *ep,
 	req->valid = valid;
 	if (valid)
 		dmacount |= BIT(VALID_BIT);
-	if (likely(!req->req.no_interrupt || !use_dma_chaining))
-		dmacount |= BIT(DMA_DONE_INTERRUPT_ENABLE);
+	dmacount |= BIT(DMA_DONE_INTERRUPT_ENABLE);
 
 	/* td->dmadesc = previously set by caller */
 	td->dmaaddr = cpu_to_le32 (req->req.dma);
@@ -862,27 +832,11 @@ static void start_dma(struct net2280_ep *ep, struct net2280_request *req)
 	req->td->dmadesc = cpu_to_le32 (ep->td_dma);
 	fill_dma_desc(ep, req, 1);
 
-	if (!use_dma_chaining)
-		req->td->dmacount |= cpu_to_le32(BIT(END_OF_CHAIN));
+	req->td->dmacount |= cpu_to_le32(BIT(END_OF_CHAIN));
 
 	start_queue(ep, tmp, req->td_dma);
 }
 
-static inline void resume_dma(struct net2280_ep *ep)
-{
-	writel(readl(&ep->dma->dmactl) | BIT(DMA_ENABLE), &ep->dma->dmactl);
-
-	ep->dma_started = true;
-}
-
-static inline void ep_stop_dma(struct net2280_ep *ep)
-{
-	writel(readl(&ep->dma->dmactl) & ~BIT(DMA_ENABLE), &ep->dma->dmactl);
-	spin_stop_dma(ep->dma);
-
-	ep->dma_started = false;
-}
-
 static inline void
 queue_dma(struct net2280_ep *ep, struct net2280_request *req, int valid)
 {
@@ -973,10 +927,8 @@ net2280_queue(struct usb_ep *_ep, struct usb_request *_req, gfp_t gfp_flags)
 			return ret;
 	}
 
-#if 0
 	ep_vdbg(dev, "%s queue req %p, len %d buf %p\n",
 			_ep->name, _req, _req->length, _req->buf);
-#endif
 
 	spin_lock_irqsave(&dev->lock, flags);
 
@@ -984,24 +936,12 @@ net2280_queue(struct usb_ep *_ep, struct usb_request *_req, gfp_t gfp_flags)
 	_req->actual = 0;
 
 	/* kickstart this i/o queue? */
-	if (list_empty(&ep->queue) && !ep->stopped) {
-		/* DMA request while EP halted */
-		if (ep->dma &&
-		    (readl(&ep->regs->ep_rsp) & BIT(CLEAR_ENDPOINT_HALT)) &&
-			(dev->quirks & PLX_SUPERSPEED)) {
-			int valid = 1;
-			if (ep->is_in) {
-				int expect;
-				expect = likely(req->req.zero ||
-						((req->req.length %
-						  ep->ep.maxpacket) != 0));
-				if (expect != ep->in_fifo_validate)
-					valid = 0;
-			}
-			queue_dma(ep, req, valid);
-		}
+	if  (list_empty(&ep->queue) && !ep->stopped &&
+		!((dev->quirks & PLX_SUPERSPEED) && ep->dma &&
+		  (readl(&ep->regs->ep_rsp) & BIT(CLEAR_ENDPOINT_HALT)))) {
+
 		/* use DMA if the endpoint supports it, else pio */
-		else if (ep->dma)
+		if (ep->dma)
 			start_dma(ep, req);
 		else {
 			/* maybe there's no control data, just status ack */
@@ -1084,8 +1024,6 @@ dma_done(struct net2280_ep *ep,	struct net2280_request *req, u32 dmacount,
 	done(ep, req, status);
 }
 
-static void restart_dma(struct net2280_ep *ep);
-
 static void scan_dma_completions(struct net2280_ep *ep)
 {
 	/* only look at descriptors that were "naturally" retired,
@@ -1117,9 +1055,8 @@ static void scan_dma_completions(struct net2280_ep *ep)
 			dma_done(ep, req, tmp, 0);
 			break;
 		} else if (!ep->is_in &&
-				(req->req.length % ep->ep.maxpacket) != 0) {
-			if (ep->dev->quirks & PLX_SUPERSPEED)
-				return dma_done(ep, req, tmp, 0);
+			   (req->req.length % ep->ep.maxpacket) &&
+			   !(ep->dev->quirks & PLX_SUPERSPEED)) {
 
 			tmp = readl(&ep->regs->ep_stat);
 			/* AVOID TROUBLE HERE by not issuing short reads from
@@ -1150,67 +1087,15 @@ static void scan_dma_completions(struct net2280_ep *ep)
 static void restart_dma(struct net2280_ep *ep)
 {
 	struct net2280_request	*req;
-	u32			dmactl = dmactl_default;
 
 	if (ep->stopped)
 		return;
 	req = list_entry(ep->queue.next, struct net2280_request, queue);
 
-	if (!use_dma_chaining) {
-		start_dma(ep, req);
-		return;
-	}
-
-	/* the 2280 will be processing the queue unless queue hiccups after
-	 * the previous transfer:
-	 *  IN:   wanted automagic zlp, head doesn't (or vice versa)
-	 *        DMA_FIFO_VALIDATE doesn't init from dma descriptors.
-	 *  OUT:  was "usb-short", we must restart.
-	 */
-	if (ep->is_in && !req->valid) {
-		struct net2280_request	*entry, *prev = NULL;
-		int			reqmode, done = 0;
-
-		ep_dbg(ep->dev, "%s dma hiccup td %p\n", ep->ep.name, req->td);
-		ep->in_fifo_validate = likely(req->req.zero ||
-				(req->req.length % ep->ep.maxpacket) != 0);
-		if (ep->in_fifo_validate)
-			dmactl |= BIT(DMA_FIFO_VALIDATE);
-		list_for_each_entry(entry, &ep->queue, queue) {
-			__le32		dmacount;
-
-			if (entry == req)
-				continue;
-			dmacount = entry->td->dmacount;
-			if (!done) {
-				reqmode = likely(entry->req.zero ||
-				   (entry->req.length % ep->ep.maxpacket));
-				if (reqmode == ep->in_fifo_validate) {
-					entry->valid = 1;
-					dmacount |= valid_bit;
-					entry->td->dmacount = dmacount;
-					prev = entry;
-					continue;
-				} else {
-					/* force a hiccup */
-					prev->td->dmacount |= dma_done_ie;
-					done = 1;
-				}
-			}
-
-			/* walk the rest of the queue so unlinks behave */
-			entry->valid = 0;
-			dmacount &= ~valid_bit;
-			entry->td->dmacount = dmacount;
-			prev = entry;
-		}
-	}
-
-	writel(0, &ep->dma->dmactl);
-	start_queue(ep, dmactl, req->td_dma);
+	start_dma(ep, req);
 }
 
-static void abort_dma_228x(struct net2280_ep *ep)
+static void abort_dma(struct net2280_ep *ep)
 {
 	/* abort the current transfer */
 	if (likely(!list_empty(&ep->queue))) {
@@ -1222,19 +1107,6 @@ static void abort_dma_228x(struct net2280_ep *ep)
 	scan_dma_completions(ep);
 }
 
-static void abort_dma_338x(struct net2280_ep *ep)
-{
-	writel(BIT(DMA_ABORT), &ep->dma->dmastat);
-	spin_stop_dma(ep->dma);
-}
-
-static void abort_dma(struct net2280_ep *ep)
-{
-	if (ep->dev->quirks & PLX_LEGACY)
-		return abort_dma_228x(ep);
-	return abort_dma_338x(ep);
-}
-
 /* dequeue ALL requests */
 static void nuke(struct net2280_ep *ep)
 {
@@ -1306,25 +1178,6 @@ static int net2280_dequeue(struct usb_ep *_ep, struct usb_request *_req)
 			done(ep, req, -ECONNRESET);
 		}
 		req = NULL;
-
-	/* patch up hardware chaining data */
-	} else if (ep->dma && use_dma_chaining) {
-		if (req->queue.prev == ep->queue.next) {
-			writel(le32_to_cpu(req->td->dmadesc),
-				&ep->dma->dmadesc);
-			if (req->td->dmacount & dma_done_ie)
-				writel(readl(&ep->dma->dmacount) |
-						le32_to_cpu(dma_done_ie),
-					&ep->dma->dmacount);
-		} else {
-			struct net2280_request	*prev;
-
-			prev = list_entry(req->queue.prev,
-				struct net2280_request, queue);
-			prev->td->dmadesc = req->td->dmadesc;
-			if (req->td->dmacount & dma_done_ie)
-				prev->td->dmacount |= dma_done_ie;
-		}
 	}
 
 	if (req)
@@ -1512,10 +1365,10 @@ static int net2280_set_selfpowered(struct usb_gadget *_gadget, int value)
 	tmp = readl(&dev->usb->usbctl);
 	if (value) {
 		tmp |= BIT(SELF_POWERED_STATUS);
-		dev->selfpowered = 1;
+		_gadget->is_selfpowered = 1;
 	} else {
 		tmp &= ~BIT(SELF_POWERED_STATUS);
-		dev->selfpowered = 0;
+		_gadget->is_selfpowered = 0;
 	}
 	writel(tmp, &dev->usb->usbctl);
 	spin_unlock_irqrestore(&dev->lock, flags);
@@ -1604,14 +1457,11 @@ static ssize_t registers_show(struct device *_dev,
 
 	/* Main Control Registers */
 	t = scnprintf(next, size, "%s version " DRIVER_VERSION
-			", chiprev %04x, dma %s\n\n"
+			", chiprev %04x\n\n"
 			"devinit %03x fifoctl %08x gadget '%s'\n"
 			"pci irqenb0 %02x irqenb1 %08x "
 			"irqstat0 %04x irqstat1 %08x\n",
 			driver_name, dev->chiprev,
-			use_dma
-				? (use_dma_chaining ? "chaining" : "enabled")
-				: "disabled",
 			readl(&dev->regs->devinit),
 			readl(&dev->regs->fifoctl),
 			s,
@@ -1913,76 +1763,73 @@ static void defect7374_disable_data_eps(struct net2280 *dev)
 static void defect7374_enable_data_eps_zero(struct net2280 *dev)
 {
 	u32 tmp = 0, tmp_reg;
-	u32 fsmvalue, scratch;
+	u32 scratch;
 	int i;
 	unsigned char ep_sel;
 
 	scratch = get_idx_reg(dev->regs, SCRATCH);
-	fsmvalue = scratch & (0xf << DEFECT7374_FSM_FIELD);
+
+	WARN_ON((scratch & (0xf << DEFECT7374_FSM_FIELD))
+		== DEFECT7374_FSM_SS_CONTROL_READ);
+
 	scratch &= ~(0xf << DEFECT7374_FSM_FIELD);
 
-	/*See if firmware needs to set up for workaround*/
-	if (fsmvalue != DEFECT7374_FSM_SS_CONTROL_READ) {
-		ep_warn(dev, "Operate Defect 7374 workaround soft this time");
-		ep_warn(dev, "It will operate on cold-reboot and SS connect");
-
-		/*GPEPs:*/
-		tmp = ((0 << ENDPOINT_NUMBER) | BIT(ENDPOINT_DIRECTION) |
-		       (2 << OUT_ENDPOINT_TYPE) | (2 << IN_ENDPOINT_TYPE) |
-		       ((dev->enhanced_mode) ?
-		       BIT(OUT_ENDPOINT_ENABLE) : BIT(ENDPOINT_ENABLE)) |
-		       BIT(IN_ENDPOINT_ENABLE));
-
-		for (i = 1; i < 5; i++)
-			writel(tmp, &dev->ep[i].cfg->ep_cfg);
-
-		/* CSRIN, PCIIN, STATIN, RCIN*/
-		tmp = ((0 << ENDPOINT_NUMBER) | BIT(ENDPOINT_ENABLE));
-		writel(tmp, &dev->dep[1].dep_cfg);
-		writel(tmp, &dev->dep[3].dep_cfg);
-		writel(tmp, &dev->dep[4].dep_cfg);
-		writel(tmp, &dev->dep[5].dep_cfg);
-
-		/*Implemented for development and debug.
-		 * Can be refined/tuned later.*/
-		for (ep_sel = 0; ep_sel <= 21; ep_sel++) {
-			/* Select an endpoint for subsequent operations: */
-			tmp_reg = readl(&dev->plregs->pl_ep_ctrl);
-			writel(((tmp_reg & ~0x1f) | ep_sel),
-			       &dev->plregs->pl_ep_ctrl);
-
-			if (ep_sel == 1) {
-				tmp =
-				    (readl(&dev->plregs->pl_ep_ctrl) |
-				     BIT(CLEAR_ACK_ERROR_CODE) | 0);
-				writel(tmp, &dev->plregs->pl_ep_ctrl);
-				continue;
-			}
+	ep_warn(dev, "Operate Defect 7374 workaround soft this time");
+	ep_warn(dev, "It will operate on cold-reboot and SS connect");
 
-			if (ep_sel == 0 || (ep_sel > 9 && ep_sel < 14) ||
-					ep_sel == 18  || ep_sel == 20)
-				continue;
+	/*GPEPs:*/
+	tmp = ((0 << ENDPOINT_NUMBER) | BIT(ENDPOINT_DIRECTION) |
+			(2 << OUT_ENDPOINT_TYPE) | (2 << IN_ENDPOINT_TYPE) |
+			((dev->enhanced_mode) ?
+			 BIT(OUT_ENDPOINT_ENABLE) : BIT(ENDPOINT_ENABLE)) |
+			BIT(IN_ENDPOINT_ENABLE));
 
-			tmp = (readl(&dev->plregs->pl_ep_cfg_4) |
-				 BIT(NON_CTRL_IN_TOLERATE_BAD_DIR) | 0);
-			writel(tmp, &dev->plregs->pl_ep_cfg_4);
+	for (i = 1; i < 5; i++)
+		writel(tmp, &dev->ep[i].cfg->ep_cfg);
 
-			tmp = readl(&dev->plregs->pl_ep_ctrl) &
-				~BIT(EP_INITIALIZED);
-			writel(tmp, &dev->plregs->pl_ep_ctrl);
+	/* CSRIN, PCIIN, STATIN, RCIN*/
+	tmp = ((0 << ENDPOINT_NUMBER) | BIT(ENDPOINT_ENABLE));
+	writel(tmp, &dev->dep[1].dep_cfg);
+	writel(tmp, &dev->dep[3].dep_cfg);
+	writel(tmp, &dev->dep[4].dep_cfg);
+	writel(tmp, &dev->dep[5].dep_cfg);
+
+	/*Implemented for development and debug.
+	 * Can be refined/tuned later.*/
+	for (ep_sel = 0; ep_sel <= 21; ep_sel++) {
+		/* Select an endpoint for subsequent operations: */
+		tmp_reg = readl(&dev->plregs->pl_ep_ctrl);
+		writel(((tmp_reg & ~0x1f) | ep_sel),
+				&dev->plregs->pl_ep_ctrl);
 
+		if (ep_sel == 1) {
+			tmp =
+				(readl(&dev->plregs->pl_ep_ctrl) |
+				 BIT(CLEAR_ACK_ERROR_CODE) | 0);
+			writel(tmp, &dev->plregs->pl_ep_ctrl);
+			continue;
 		}
 
-		/* Set FSM to focus on the first Control Read:
-		 * - Tip: Connection speed is known upon the first
-		 * setup request.*/
-		scratch |= DEFECT7374_FSM_WAITING_FOR_CONTROL_READ;
-		set_idx_reg(dev->regs, SCRATCH, scratch);
+		if (ep_sel == 0 || (ep_sel > 9 && ep_sel < 14) ||
+				ep_sel == 18  || ep_sel == 20)
+			continue;
+
+		tmp = (readl(&dev->plregs->pl_ep_cfg_4) |
+				BIT(NON_CTRL_IN_TOLERATE_BAD_DIR) | 0);
+		writel(tmp, &dev->plregs->pl_ep_cfg_4);
+
+		tmp = readl(&dev->plregs->pl_ep_ctrl) &
+			~BIT(EP_INITIALIZED);
+		writel(tmp, &dev->plregs->pl_ep_ctrl);
 
-	} else{
-		ep_warn(dev, "Defect 7374 workaround soft will NOT operate");
-		ep_warn(dev, "It will operate on cold-reboot and SS connect");
 	}
+
+	/* Set FSM to focus on the first Control Read:
+	 * - Tip: Connection speed is known upon the first
+	 * setup request.*/
+	scratch |= DEFECT7374_FSM_WAITING_FOR_CONTROL_READ;
+	set_idx_reg(dev->regs, SCRATCH, scratch);
+
 }
 
 /* keeping it simple:
@@ -2033,21 +1880,13 @@ static void usb_reset_228x(struct net2280 *dev)
 static void usb_reset_338x(struct net2280 *dev)
 {
 	u32 tmp;
-	u32 fsmvalue;
 
 	dev->gadget.speed = USB_SPEED_UNKNOWN;
 	(void)readl(&dev->usb->usbctl);
 
 	net2280_led_init(dev);
 
-	fsmvalue = get_idx_reg(dev->regs, SCRATCH) &
-			(0xf << DEFECT7374_FSM_FIELD);
-
-	/* See if firmware needs to set up for workaround: */
-	if (fsmvalue != DEFECT7374_FSM_SS_CONTROL_READ) {
-		ep_info(dev, "%s: Defect 7374 FsmValue 0x%08x\n", __func__,
-		     fsmvalue);
-	} else {
+	if (dev->bug7734_patched) {
 		/* disable automatic responses, and irqs */
 		writel(0, &dev->usb->stdrsp);
 		writel(0, &dev->regs->pciirqenb0);
@@ -2064,7 +1903,7 @@ static void usb_reset_338x(struct net2280 *dev)
 
 	writel(~0, &dev->regs->irqstat0), writel(~0, &dev->regs->irqstat1);
 
-	if (fsmvalue == DEFECT7374_FSM_SS_CONTROL_READ) {
+	if (dev->bug7734_patched) {
 		/* reset, and enable pci */
 		tmp = readl(&dev->regs->devinit) |
 		    BIT(PCI_ENABLE) |
@@ -2093,10 +1932,6 @@ static void usb_reset(struct net2280 *dev)
 static void usb_reinit_228x(struct net2280 *dev)
 {
 	u32	tmp;
-	int	init_dma;
-
-	/* use_dma changes are ignored till next device re-init */
-	init_dma = use_dma;
 
 	/* basic endpoint init */
 	for (tmp = 0; tmp < 7; tmp++) {
@@ -2108,8 +1943,7 @@ static void usb_reinit_228x(struct net2280 *dev)
 
 		if (tmp > 0 && tmp <= 4) {
 			ep->fifo_size = 1024;
-			if (init_dma)
-				ep->dma = &dev->dma[tmp - 1];
+			ep->dma = &dev->dma[tmp - 1];
 		} else
 			ep->fifo_size = 64;
 		ep->regs = &dev->epregs[tmp];
@@ -2133,17 +1967,12 @@ static void usb_reinit_228x(struct net2280 *dev)
 
 static void usb_reinit_338x(struct net2280 *dev)
 {
-	int init_dma;
 	int i;
 	u32 tmp, val;
-	u32 fsmvalue;
 	static const u32 ne[9] = { 0, 1, 2, 3, 4, 1, 2, 3, 4 };
 	static const u32 ep_reg_addr[9] = { 0x00, 0xC0, 0x00, 0xC0, 0x00,
 						0x00, 0xC0, 0x00, 0xC0 };
 
-	/* use_dma changes are ignored till next device re-init */
-	init_dma = use_dma;
-
 	/* basic endpoint init */
 	for (i = 0; i < dev->n_ep; i++) {
 		struct net2280_ep *ep = &dev->ep[i];
@@ -2152,7 +1981,7 @@ static void usb_reinit_338x(struct net2280 *dev)
 		ep->dev = dev;
 		ep->num = i;
 
-		if (i > 0 && i <= 4 && init_dma)
+		if (i > 0 && i <= 4)
 			ep->dma = &dev->dma[i - 1];
 
 		if (dev->enhanced_mode) {
@@ -2177,14 +2006,7 @@ static void usb_reinit_338x(struct net2280 *dev)
 	dev->ep[0].stopped = 0;
 
 	/* Link layer set up */
-	fsmvalue = get_idx_reg(dev->regs, SCRATCH) &
-				(0xf << DEFECT7374_FSM_FIELD);
-
-	/* See if driver needs to set up for workaround: */
-	if (fsmvalue != DEFECT7374_FSM_SS_CONTROL_READ)
-		ep_info(dev, "%s: Defect 7374 FsmValue %08x\n",
-						__func__, fsmvalue);
-	else {
+	if (dev->bug7734_patched) {
 		tmp = readl(&dev->usb_ext->usbctl2) &
 		    ~(BIT(U1_ENABLE) | BIT(U2_ENABLE) | BIT(LTM_ENABLE));
 		writel(tmp, &dev->usb_ext->usbctl2);
@@ -2291,15 +2113,8 @@ static void ep0_start_228x(struct net2280 *dev)
 
 static void ep0_start_338x(struct net2280 *dev)
 {
-	u32 fsmvalue;
-
-	fsmvalue = get_idx_reg(dev->regs, SCRATCH) &
-			(0xf << DEFECT7374_FSM_FIELD);
 
-	if (fsmvalue != DEFECT7374_FSM_SS_CONTROL_READ)
-		ep_info(dev, "%s: Defect 7374 FsmValue %08x\n", __func__,
-		     fsmvalue);
-	else
+	if (dev->bug7734_patched)
 		writel(BIT(CLEAR_NAK_OUT_PACKETS_MODE) |
 		       BIT(SET_EP_HIDE_STATUS_PHASE),
 		       &dev->epregs[0].ep_rsp);
@@ -2382,16 +2197,12 @@ static int net2280_start(struct usb_gadget *_gadget,
 	if (retval)
 		goto err_func;
 
-	/* Enable force-full-speed testing mode, if desired */
-	if (full_speed && (dev->quirks & PLX_LEGACY))
-		writel(BIT(FORCE_FULL_SPEED_MODE), &dev->usb->xcvrdiag);
-
-	/* ... then enable host detection and ep0; and we're ready
+	/* enable host detection and ep0; and we're ready
 	 * for set_configuration as well as eventual disconnect.
 	 */
 	net2280_led_active(dev, 1);
 
-	if (dev->quirks & PLX_SUPERSPEED)
+	if ((dev->quirks & PLX_SUPERSPEED) && !dev->bug7734_patched)
 		defect7374_enable_data_eps_zero(dev);
 
 	ep0_start(dev);
@@ -2444,10 +2255,6 @@ static int net2280_stop(struct usb_gadget *_gadget)
 
 	net2280_led_active(dev, 0);
 
-	/* Disable full-speed test mode */
-	if (dev->quirks & PLX_LEGACY)
-		writel(0, &dev->usb->xcvrdiag);
-
 	device_remove_file(&dev->pdev->dev, &dev_attr_function);
 	device_remove_file(&dev->pdev->dev, &dev_attr_queues);
 
@@ -2478,10 +2285,10 @@ static void handle_ep_small(struct net2280_ep *ep)
 	/* ack all, and handle what we care about */
 	t = readl(&ep->regs->ep_stat);
 	ep->irqs++;
-#if 0
+
 	ep_vdbg(ep->dev, "%s ack ep_stat %08x, req %p\n",
-			ep->ep.name, t, req ? &req->req : 0);
-#endif
+			ep->ep.name, t, req ? &req->req : NULL);
+
 	if (!ep->is_in || (ep->dev->quirks & PLX_2280))
 		writel(t & ~BIT(NAK_OUT_PACKETS), &ep->regs->ep_stat);
 	else
@@ -2717,6 +2524,7 @@ static void defect7374_workaround(struct net2280 *dev, struct usb_ctrlrequest r)
 		 * run after the next USB connection.
 		 */
 		scratch |= DEFECT7374_FSM_NON_SS_CONTROL_READ;
+		dev->bug7734_patched = 1;
 		goto restore_data_eps;
 	}
 
@@ -2730,6 +2538,7 @@ static void defect7374_workaround(struct net2280 *dev, struct usb_ctrlrequest r)
 		if ((state >= (ACK_GOOD_NORMAL << STATE)) &&
 			(state <= (ACK_GOOD_MORE_ACKS_TO_COME << STATE))) {
 			scratch |= DEFECT7374_FSM_SS_CONTROL_READ;
+			dev->bug7734_patched = 1;
 			break;
 		}
 
@@ -2766,80 +2575,19 @@ restore_data_eps:
 	return;
 }
 
-static void ep_stall(struct net2280_ep *ep, int stall)
+static void ep_clear_seqnum(struct net2280_ep *ep)
 {
 	struct net2280 *dev = ep->dev;
 	u32 val;
 	static const u32 ep_pl[9] = { 0, 3, 4, 7, 8, 2, 5, 6, 9 };
 
-	if (stall) {
-		writel(BIT(SET_ENDPOINT_HALT) |
-		       /* BIT(SET_NAK_PACKETS) | */
-		       BIT(CLEAR_CONTROL_STATUS_PHASE_HANDSHAKE),
-		       &ep->regs->ep_rsp);
-		ep->is_halt = 1;
-	} else {
-		if (dev->gadget.speed == USB_SPEED_SUPER) {
-			/*
-			 * Workaround for SS SeqNum not cleared via
-			 * Endpoint Halt (Clear) bit. select endpoint
-			 */
-			val = readl(&dev->plregs->pl_ep_ctrl);
-			val = (val & ~0x1f) | ep_pl[ep->num];
-			writel(val, &dev->plregs->pl_ep_ctrl);
-
-			val |= BIT(SEQUENCE_NUMBER_RESET);
-			writel(val, &dev->plregs->pl_ep_ctrl);
-		}
-		val = readl(&ep->regs->ep_rsp);
-		val |= BIT(CLEAR_ENDPOINT_HALT) |
-			BIT(CLEAR_ENDPOINT_TOGGLE);
-		writel(val,
-		       /* | BIT(CLEAR_NAK_PACKETS),*/
-		       &ep->regs->ep_rsp);
-		ep->is_halt = 0;
-		val = readl(&ep->regs->ep_rsp);
-	}
-}
-
-static void ep_stdrsp(struct net2280_ep *ep, int value, int wedged)
-{
-	/* set/clear, then synch memory views with the device */
-	if (value) {
-		ep->stopped = 1;
-		if (ep->num == 0)
-			ep->dev->protocol_stall = 1;
-		else {
-			if (ep->dma)
-				ep_stop_dma(ep);
-			ep_stall(ep, true);
-		}
-
-		if (wedged)
-			ep->wedged = 1;
-	} else {
-		ep->stopped = 0;
-		ep->wedged = 0;
-
-		ep_stall(ep, false);
+	val = readl(&dev->plregs->pl_ep_ctrl) & ~0x1f;
+	val |= ep_pl[ep->num];
+	writel(val, &dev->plregs->pl_ep_ctrl);
+	val |= BIT(SEQUENCE_NUMBER_RESET);
+	writel(val, &dev->plregs->pl_ep_ctrl);
 
-		/* Flush the queue */
-		if (!list_empty(&ep->queue)) {
-			struct net2280_request *req =
-			    list_entry(ep->queue.next, struct net2280_request,
-				       queue);
-			if (ep->dma)
-				resume_dma(ep);
-			else {
-				if (ep->is_in)
-					write_fifo(ep, &req->req);
-				else {
-					if (read_fifo(ep, req))
-						done(ep, req, 0);
-				}
-			}
-		}
-	}
+	return;
 }
 
 static void handle_stat0_irqs_superspeed(struct net2280 *dev,
@@ -2863,7 +2611,7 @@ static void handle_stat0_irqs_superspeed(struct net2280 *dev,
 		switch (r.bRequestType) {
 		case (USB_DIR_IN | USB_TYPE_STANDARD | USB_RECIP_DEVICE):
 			status = dev->wakeup_enable ? 0x02 : 0x00;
-			if (dev->selfpowered)
+			if (dev->gadget.is_selfpowered)
 				status |= BIT(0);
 			status |= (dev->u1_enable << 2 | dev->u2_enable << 3 |
 							dev->ltm_enable << 4);
@@ -2940,7 +2688,12 @@ static void handle_stat0_irqs_superspeed(struct net2280 *dev,
 			if (w_value != USB_ENDPOINT_HALT)
 				goto do_stall3;
 			ep_vdbg(dev, "%s clear halt\n", e->ep.name);
-			ep_stall(e, false);
+			/*
+			 * Workaround for SS SeqNum not cleared via
+			 * Endpoint Halt (Clear) bit. select endpoint
+			 */
+			ep_clear_seqnum(e);
+			clear_halt(e);
 			if (!list_empty(&e->queue) && e->td_dma)
 				restart_dma(e);
 			allow_status(ep);
@@ -2998,7 +2751,14 @@ static void handle_stat0_irqs_superspeed(struct net2280 *dev,
 			e = get_ep_by_addr(dev,	w_index);
 			if (!e || (w_value != USB_ENDPOINT_HALT))
 				goto do_stall3;
-			ep_stdrsp(e, true, false);
+			ep->stopped = 1;
+			if (ep->num == 0)
+				ep->dev->protocol_stall = 1;
+			else {
+				if (ep->dma)
+					abort_dma(ep);
+				set_halt(ep);
+			}
 			allow_status_338x(ep);
 			break;
 
@@ -3026,7 +2786,7 @@ do_stall3:
 				r.bRequestType, r.bRequest, tmp);
 		dev->protocol_stall = 1;
 		/* TD 9.9 Halt Endpoint test. TD 9.22 Set feature test */
-		ep_stall(ep, true);
+		set_halt(ep);
 	}
 
 next_endpoints3:
@@ -3091,9 +2851,7 @@ static void handle_stat0_irqs(struct net2280 *dev, u32 stat)
 		}
 		ep->stopped = 0;
 		dev->protocol_stall = 0;
-		if (dev->quirks & PLX_SUPERSPEED)
-			ep->is_halt = 0;
-		else{
+		if (!(dev->quirks & PLX_SUPERSPEED)) {
 			if (ep->dev->quirks & PLX_2280)
 				tmp = BIT(FIFO_OVERFLOW) |
 				    BIT(FIFO_UNDERFLOW);
@@ -3120,7 +2878,7 @@ static void handle_stat0_irqs(struct net2280 *dev, u32 stat)
 		cpu_to_le32s(&u.raw[0]);
 		cpu_to_le32s(&u.raw[1]);
 
-		if (dev->quirks & PLX_SUPERSPEED)
+		if ((dev->quirks & PLX_SUPERSPEED) && !dev->bug7734_patched)
 			defect7374_workaround(dev, u.r);
 
 		tmp = 0;
@@ -3423,17 +3181,12 @@ static void handle_stat1_irqs(struct net2280 *dev, u32 stat)
 				continue;
 		}
 
-		/* chaining should stop on abort, short OUT from fifo,
-		 * or (stat0 codepath) short OUT transfer.
-		 */
-		if (!use_dma_chaining) {
-			if (!(tmp & BIT(DMA_TRANSACTION_DONE_INTERRUPT))) {
-				ep_dbg(ep->dev, "%s no xact done? %08x\n",
-					ep->ep.name, tmp);
-				continue;
-			}
-			stop_dma(ep->dma);
+		if (!(tmp & BIT(DMA_TRANSACTION_DONE_INTERRUPT))) {
+			ep_dbg(ep->dev, "%s no xact done? %08x\n",
+				ep->ep.name, tmp);
+			continue;
 		}
+		stop_dma(ep->dma);
 
 		/* OUT transfers terminate when the data from the
 		 * host is in our memory.  Process whatever's done.
@@ -3448,30 +3201,9 @@ static void handle_stat1_irqs(struct net2280 *dev, u32 stat)
 		scan_dma_completions(ep);
 
 		/* disable dma on inactive queues; else maybe restart */
-		if (list_empty(&ep->queue)) {
-			if (use_dma_chaining)
-				stop_dma(ep->dma);
-		} else {
+		if (!list_empty(&ep->queue)) {
 			tmp = readl(&dma->dmactl);
-			if (!use_dma_chaining || (tmp & BIT(DMA_ENABLE)) == 0)
-				restart_dma(ep);
-			else if (ep->is_in && use_dma_chaining) {
-				struct net2280_request	*req;
-				__le32			dmacount;
-
-				/* the descriptor at the head of the chain
-				 * may still have VALID_BIT clear; that's
-				 * used to trigger changing DMA_FIFO_VALIDATE
-				 * (affects automagic zlp writes).
-				 */
-				req = list_entry(ep->queue.next,
-						struct net2280_request, queue);
-				dmacount = req->td->dmacount;
-				dmacount &= cpu_to_le32(BIT(VALID_BIT) |
-						DMA_BYTE_COUNT_MASK);
-				if (dmacount && (dmacount & valid_bit) == 0)
-					restart_dma(ep);
-			}
+			restart_dma(ep);
 		}
 		ep->irqs++;
 	}
@@ -3556,7 +3288,7 @@ static void net2280_remove(struct pci_dev *pdev)
 	}
 	if (dev->got_irq)
 		free_irq(pdev->irq, dev);
-	if (use_msi && dev->quirks & PLX_SUPERSPEED)
+	if (dev->quirks & PLX_SUPERSPEED)
 		pci_disable_msi(pdev);
 	if (dev->regs)
 		iounmap(dev->regs);
@@ -3581,9 +3313,6 @@ static int net2280_probe(struct pci_dev *pdev, const struct pci_device_id *id)
 	void			__iomem *base = NULL;
 	int			retval, i;
 
-	if (!use_dma)
-		use_dma_chaining = 0;
-
 	/* alloc, and start init */
 	dev = kzalloc(sizeof(*dev), GFP_KERNEL);
 	if (dev == NULL) {
@@ -3663,9 +3392,12 @@ static int net2280_probe(struct pci_dev *pdev, const struct pci_device_id *id)
 		fsmvalue = get_idx_reg(dev->regs, SCRATCH) &
 					(0xf << DEFECT7374_FSM_FIELD);
 		/* See if firmware needs to set up for workaround: */
-		if (fsmvalue == DEFECT7374_FSM_SS_CONTROL_READ)
+		if (fsmvalue == DEFECT7374_FSM_SS_CONTROL_READ) {
+			dev->bug7734_patched = 1;
 			writel(0, &dev->usb->usbctl);
-	} else{
+		} else
+			dev->bug7734_patched = 0;
+	} else {
 		dev->enhanced_mode = 0;
 		dev->n_ep = 7;
 		/* put into initial config, link up all endpoints */
@@ -3682,7 +3414,7 @@ static int net2280_probe(struct pci_dev *pdev, const struct pci_device_id *id)
 		goto done;
 	}
 
-	if (use_msi && (dev->quirks & PLX_SUPERSPEED))
+	if (dev->quirks & PLX_SUPERSPEED)
 		if (pci_enable_msi(pdev))
 			ep_err(dev, "Failed to enable MSI mode\n");
 
@@ -3741,9 +3473,7 @@ static int net2280_probe(struct pci_dev *pdev, const struct pci_device_id *id)
 	ep_info(dev, "%s\n", driver_desc);
 	ep_info(dev, "irq %d, pci mem %p, chip rev %04x\n",
 			pdev->irq, base, dev->chiprev);
-	ep_info(dev, "version: " DRIVER_VERSION "; dma %s %s\n",
-		use_dma	? (use_dma_chaining ? "chaining" : "enabled")
-			: "disabled",
+	ep_info(dev, "version: " DRIVER_VERSION "; %s\n",
 		dev->enhanced_mode ? "enhanced mode" : "legacy mode");
 	retval = device_create_file(&pdev->dev, &dev_attr_registers);
 	if (retval)
@@ -3776,9 +3506,6 @@ static void net2280_shutdown(struct pci_dev *pdev)
 	/* disable the pullup so the host will think we're gone */
 	writel(0, &dev->usb->usbctl);
 
-	/* Disable full-speed test mode */
-	if (dev->quirks & PLX_LEGACY)
-		writel(0, &dev->usb->xcvrdiag);
 }