pinctrl: Pass all configs to driver on pin_config_set()

When setting pin configuration in the pinctrl framework, pin_config_set() or
pin_config_group_set() is called in a loop to set one configuration at a time
for the specified pin or group.

This patch 1) removes the loop and 2) changes the API to pass the whole pin
config array to the driver.  It is now up to the driver to loop through the
configs.  This allows the driver to potentially combine configs and reduce the
number of writes to pin config registers.

All c files changed have been build-tested to verify the change compiles and
that the corresponding .o is successfully generated.

Signed-off-by: Sherman Yin <syin@broadcom.com>
Reviewed-by: Christian Daudt <csd@broadcom.com>
Reviewed-by: Matt Porter <matt.porter@linaro.org>
Tested-by: Stephen Warren <swarren@nvidia.com>
Acked-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>

1 files changed, 25 insertions, 18 deletions

diff --git a/drivers/pinctrl/pinctrl-bcm2835.c b/drivers/pinctrl/pinctrl-bcm2835.c
index a1c88b30f71f..c05c1ef2cc3c 100644
--- a/drivers/pinctrl/pinctrl-bcm2835.c
+++ b/drivers/pinctrl/pinctrl-bcm2835.c
@@ -893,28 +893,35 @@ static int bcm2835_pinconf_get(struct pinctrl_dev *pctldev,
 }
 
 static int bcm2835_pinconf_set(struct pinctrl_dev *pctldev,
-			unsigned pin, unsigned long config)
+			unsigned pin, unsigned long *configs,
+			unsigned num_configs)
 {
 	struct bcm2835_pinctrl *pc = pinctrl_dev_get_drvdata(pctldev);
-	enum bcm2835_pinconf_param param = BCM2835_PINCONF_UNPACK_PARAM(config);
-	u16 arg = BCM2835_PINCONF_UNPACK_ARG(config);
+	enum bcm2835_pinconf_param param;
+	u16 arg;
 	u32 off, bit;
+	int i;
 
-	if (param != BCM2835_PINCONF_PARAM_PULL)
-		return -EINVAL;
-
-	off = GPIO_REG_OFFSET(pin);
-	bit = GPIO_REG_SHIFT(pin);
-
-	bcm2835_gpio_wr(pc, GPPUD, arg & 3);
-	/*
-	 * Docs say to wait 150 cycles, but not of what. We assume a
-	 * 1 MHz clock here, which is pretty slow...
-	 */
-	udelay(150);
-	bcm2835_gpio_wr(pc, GPPUDCLK0 + (off * 4), BIT(bit));
-	udelay(150);
-	bcm2835_gpio_wr(pc, GPPUDCLK0 + (off * 4), 0);
+	for (i = 0; i < num_configs; i++) {
+		param = BCM2835_PINCONF_UNPACK_PARAM(configs[i]);
+		arg = BCM2835_PINCONF_UNPACK_ARG(configs[i]);
+
+		if (param != BCM2835_PINCONF_PARAM_PULL)
+			return -EINVAL;
+
+		off = GPIO_REG_OFFSET(pin);
+		bit = GPIO_REG_SHIFT(pin);
+
+		bcm2835_gpio_wr(pc, GPPUD, arg & 3);
+		/*
+		 * Docs say to wait 150 cycles, but not of what. We assume a
+		 * 1 MHz clock here, which is pretty slow...
+		 */
+		udelay(150);
+		bcm2835_gpio_wr(pc, GPPUDCLK0 + (off * 4), BIT(bit));
+		udelay(150);
+		bcm2835_gpio_wr(pc, GPPUDCLK0 + (off * 4), 0);
+	} /* for each config */
 
 	return 0;
 }