iwlwifi: split the drivers for agn and legacy devices 3945/4965

Intel WiFi devices 3945 and 4965 now have their own driver in the folder

	drivers/net/wireless/iwlegacy

Add support to build these drivers independently of the driver for
AGN devices. Selecting the 3945 builds iwl3945.ko and iwl_legacy.ko,
and selecting the 4965 builds iwl4965.ko and iwl_legacy.ko. iwl-legacy.ko
contains code shared between both devices.

The 3945 is an ABG/BG device, with no support for 802.11n. The 4965 is a 2x3
ABGN device.

Signed-off-by: Meenakshi Venkataraman <meenakshi.venkataraman@intel.com>
Acked-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>

1 files changed, 0 insertions, 792 deletions

diff --git a/drivers/net/wireless/iwlwifi/iwl-4965-hw.h b/drivers/net/wireless/iwlwifi/iwl-4965-hw.h
deleted file mode 100644
index 9166794eda0d..000000000000
--- a/drivers/net/wireless/iwlwifi/iwl-4965-hw.h
+++ /dev/null
@@ -1,792 +0,0 @@
-/******************************************************************************
- *
- * This file is provided under a dual BSD/GPLv2 license.  When using or
- * redistributing this file, you may do so under either license.
- *
- * GPL LICENSE SUMMARY
- *
- * Copyright(c) 2005 - 2010 Intel Corporation. All rights reserved.
- *
- * This program is free software; you can redistribute it and/or modify
- * it under the terms of version 2 of the GNU General Public License as
- * published by the Free Software Foundation.
- *
- * This program is distributed in the hope that it will be useful, but
- * WITHOUT ANY WARRANTY; without even the implied warranty of
- * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the GNU
- * General Public License for more details.
- *
- * You should have received a copy of the GNU General Public License
- * along with this program; if not, write to the Free Software
- * Foundation, Inc., 51 Franklin Street, Fifth Floor, Boston, MA 02110,
- * USA
- *
- * The full GNU General Public License is included in this distribution
- * in the file called LICENSE.GPL.
- *
- * Contact Information:
- *  Intel Linux Wireless <ilw@linux.intel.com>
- * Intel Corporation, 5200 N.E. Elam Young Parkway, Hillsboro, OR 97124-6497
- *
- * BSD LICENSE
- *
- * Copyright(c) 2005 - 2010 Intel Corporation. All rights reserved.
- * All rights reserved.
- *
- * Redistribution and use in source and binary forms, with or without
- * modification, are permitted provided that the following conditions
- * are met:
- *
- *  * Redistributions of source code must retain the above copyright
- *    notice, this list of conditions and the following disclaimer.
- *  * Redistributions in binary form must reproduce the above copyright
- *    notice, this list of conditions and the following disclaimer in
- *    the documentation and/or other materials provided with the
- *    distribution.
- *  * Neither the name Intel Corporation nor the names of its
- *    contributors may be used to endorse or promote products derived
- *    from this software without specific prior written permission.
- *
- * THIS SOFTWARE IS PROVIDED BY THE COPYRIGHT HOLDERS AND CONTRIBUTORS
- * "AS IS" AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT
- * LIMITED TO, THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR
- * A PARTICULAR PURPOSE ARE DISCLAIMED. IN NO EVENT SHALL THE COPYRIGHT
- * OWNER OR CONTRIBUTORS BE LIABLE FOR ANY DIRECT, INDIRECT, INCIDENTAL,
- * SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES (INCLUDING, BUT NOT
- * LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES; LOSS OF USE,
- * DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER CAUSED AND ON ANY
- * THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT LIABILITY, OR TORT
- * (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY OUT OF THE USE
- * OF THIS SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGE.
- *
- *****************************************************************************/
-/*
- * Please use this file (iwl-4965-hw.h) only for hardware-related definitions.
- * Use iwl-commands.h for uCode API definitions.
- * Use iwl-dev.h for driver implementation definitions.
- */
-
-#ifndef __iwl_4965_hw_h__
-#define __iwl_4965_hw_h__
-
-#include "iwl-fh.h"
-
-/* EEPROM */
-#define IWL4965_EEPROM_IMG_SIZE			1024
-
-/*
- * uCode queue management definitions ...
- * The first queue used for block-ack aggregation is #7 (4965 only).
- * All block-ack aggregation queues should map to Tx DMA/FIFO channel 7.
- */
-#define IWL49_FIRST_AMPDU_QUEUE	7
-
-/* Sizes and addresses for instruction and data memory (SRAM) in
- * 4965's embedded processor.  Driver access is via HBUS_TARG_MEM_* regs. */
-#define IWL49_RTC_INST_LOWER_BOUND		(0x000000)
-#define IWL49_RTC_INST_UPPER_BOUND		(0x018000)
-
-#define IWL49_RTC_DATA_LOWER_BOUND		(0x800000)
-#define IWL49_RTC_DATA_UPPER_BOUND		(0x80A000)
-
-#define IWL49_RTC_INST_SIZE  (IWL49_RTC_INST_UPPER_BOUND - \
-				IWL49_RTC_INST_LOWER_BOUND)
-#define IWL49_RTC_DATA_SIZE  (IWL49_RTC_DATA_UPPER_BOUND - \
-				IWL49_RTC_DATA_LOWER_BOUND)
-
-#define IWL49_MAX_INST_SIZE IWL49_RTC_INST_SIZE
-#define IWL49_MAX_DATA_SIZE IWL49_RTC_DATA_SIZE
-
-/* Size of uCode instruction memory in bootstrap state machine */
-#define IWL49_MAX_BSM_SIZE BSM_SRAM_SIZE
-
-static inline int iwl4965_hw_valid_rtc_data_addr(u32 addr)
-{
-	return (addr >= IWL49_RTC_DATA_LOWER_BOUND) &&
-	       (addr < IWL49_RTC_DATA_UPPER_BOUND);
-}
-
-/********************* START TEMPERATURE *************************************/
-
-/**
- * 4965 temperature calculation.
- *
- * The driver must calculate the device temperature before calculating
- * a txpower setting (amplifier gain is temperature dependent).  The
- * calculation uses 4 measurements, 3 of which (R1, R2, R3) are calibration
- * values used for the life of the driver, and one of which (R4) is the
- * real-time temperature indicator.
- *
- * uCode provides all 4 values to the driver via the "initialize alive"
- * notification (see struct iwl4965_init_alive_resp).  After the runtime uCode
- * image loads, uCode updates the R4 value via statistics notifications
- * (see STATISTICS_NOTIFICATION), which occur after each received beacon
- * when associated, or can be requested via REPLY_STATISTICS_CMD.
- *
- * NOTE:  uCode provides the R4 value as a 23-bit signed value.  Driver
- *        must sign-extend to 32 bits before applying formula below.
- *
- * Formula:
- *
- * degrees Kelvin = ((97 * 259 * (R4 - R2) / (R3 - R1)) / 100) + 8
- *
- * NOTE:  The basic formula is 259 * (R4-R2) / (R3-R1).  The 97/100 is
- * an additional correction, which should be centered around 0 degrees
- * Celsius (273 degrees Kelvin).  The 8 (3 percent of 273) compensates for
- * centering the 97/100 correction around 0 degrees K.
- *
- * Add 273 to Kelvin value to find degrees Celsius, for comparing current
- * temperature with factory-measured temperatures when calculating txpower
- * settings.
- */
-#define TEMPERATURE_CALIB_KELVIN_OFFSET 8
-#define TEMPERATURE_CALIB_A_VAL 259
-
-/* Limit range of calculated temperature to be between these Kelvin values */
-#define IWL_TX_POWER_TEMPERATURE_MIN  (263)
-#define IWL_TX_POWER_TEMPERATURE_MAX  (410)
-
-#define IWL_TX_POWER_TEMPERATURE_OUT_OF_RANGE(t) \
-	(((t) < IWL_TX_POWER_TEMPERATURE_MIN) || \
-	 ((t) > IWL_TX_POWER_TEMPERATURE_MAX))
-
-/********************* END TEMPERATURE ***************************************/
-
-/********************* START TXPOWER *****************************************/
-
-/**
- * 4965 txpower calculations rely on information from three sources:
- *
- *     1) EEPROM
- *     2) "initialize" alive notification
- *     3) statistics notifications
- *
- * EEPROM data consists of:
- *
- * 1)  Regulatory information (max txpower and channel usage flags) is provided
- *     separately for each channel that can possibly supported by 4965.
- *     40 MHz wide (.11n HT40) channels are listed separately from 20 MHz
- *     (legacy) channels.
- *
- *     See struct iwl4965_eeprom_channel for format, and struct iwl4965_eeprom
- *     for locations in EEPROM.
- *
- * 2)  Factory txpower calibration information is provided separately for
- *     sub-bands of contiguous channels.  2.4GHz has just one sub-band,
- *     but 5 GHz has several sub-bands.
- *
- *     In addition, per-band (2.4 and 5 Ghz) saturation txpowers are provided.
- *
- *     See struct iwl4965_eeprom_calib_info (and the tree of structures
- *     contained within it) for format, and struct iwl4965_eeprom for
- *     locations in EEPROM.
- *
- * "Initialization alive" notification (see struct iwl4965_init_alive_resp)
- * consists of:
- *
- * 1)  Temperature calculation parameters.
- *
- * 2)  Power supply voltage measurement.
- *
- * 3)  Tx gain compensation to balance 2 transmitters for MIMO use.
- *
- * Statistics notifications deliver:
- *
- * 1)  Current values for temperature param R4.
- */
-
-/**
- * To calculate a txpower setting for a given desired target txpower, channel,
- * modulation bit rate, and transmitter chain (4965 has 2 transmitters to
- * support MIMO and transmit diversity), driver must do the following:
- *
- * 1)  Compare desired txpower vs. (EEPROM) regulatory limit for this channel.
- *     Do not exceed regulatory limit; reduce target txpower if necessary.
- *
- *     If setting up txpowers for MIMO rates (rate indexes 8-15, 24-31),
- *     2 transmitters will be used simultaneously; driver must reduce the
- *     regulatory limit by 3 dB (half-power) for each transmitter, so the
- *     combined total output of the 2 transmitters is within regulatory limits.
- *
- *
- * 2)  Compare target txpower vs. (EEPROM) saturation txpower *reduced by
- *     backoff for this bit rate*.  Do not exceed (saturation - backoff[rate]);
- *     reduce target txpower if necessary.
- *
- *     Backoff values below are in 1/2 dB units (equivalent to steps in
- *     txpower gain tables):
- *
- *     OFDM 6 - 36 MBit:  10 steps (5 dB)
- *     OFDM 48 MBit:      15 steps (7.5 dB)
- *     OFDM 54 MBit:      17 steps (8.5 dB)
- *     OFDM 60 MBit:      20 steps (10 dB)
- *     CCK all rates:     10 steps (5 dB)
- *
- *     Backoff values apply to saturation txpower on a per-transmitter basis;
- *     when using MIMO (2 transmitters), each transmitter uses the same
- *     saturation level provided in EEPROM, and the same backoff values;
- *     no reduction (such as with regulatory txpower limits) is required.
- *
- *     Saturation and Backoff values apply equally to 20 Mhz (legacy) channel
- *     widths and 40 Mhz (.11n HT40) channel widths; there is no separate
- *     factory measurement for ht40 channels.
- *
- *     The result of this step is the final target txpower.  The rest of
- *     the steps figure out the proper settings for the device to achieve
- *     that target txpower.
- *
- *
- * 3)  Determine (EEPROM) calibration sub band for the target channel, by
- *     comparing against first and last channels in each sub band
- *     (see struct iwl4965_eeprom_calib_subband_info).
- *
- *
- * 4)  Linearly interpolate (EEPROM) factory calibration measurement sets,
- *     referencing the 2 factory-measured (sample) channels within the sub band.
- *
- *     Interpolation is based on difference between target channel's frequency
- *     and the sample channels' frequencies.  Since channel numbers are based
- *     on frequency (5 MHz between each channel number), this is equivalent
- *     to interpolating based on channel number differences.
- *
- *     Note that the sample channels may or may not be the channels at the
- *     edges of the sub band.  The target channel may be "outside" of the
- *     span of the sampled channels.
- *
- *     Driver may choose the pair (for 2 Tx chains) of measurements (see
- *     struct iwl4965_eeprom_calib_ch_info) for which the actual measured
- *     txpower comes closest to the desired txpower.  Usually, though,
- *     the middle set of measurements is closest to the regulatory limits,
- *     and is therefore a good choice for all txpower calculations (this
- *     assumes that high accuracy is needed for maximizing legal txpower,
- *     while lower txpower configurations do not need as much accuracy).
- *
- *     Driver should interpolate both members of the chosen measurement pair,
- *     i.e. for both Tx chains (radio transmitters), unless the driver knows
- *     that only one of the chains will be used (e.g. only one tx antenna
- *     connected, but this should be unusual).  The rate scaling algorithm
- *     switches antennas to find best performance, so both Tx chains will
- *     be used (although only one at a time) even for non-MIMO transmissions.
- *
- *     Driver should interpolate factory values for temperature, gain table
- *     index, and actual power.  The power amplifier detector values are
- *     not used by the driver.
- *
- *     Sanity check:  If the target channel happens to be one of the sample
- *     channels, the results should agree with the sample channel's
- *     measurements!
- *
- *
- * 5)  Find difference between desired txpower and (interpolated)
- *     factory-measured txpower.  Using (interpolated) factory gain table index
- *     (shown elsewhere) as a starting point, adjust this index lower to
- *     increase txpower, or higher to decrease txpower, until the target
- *     txpower is reached.  Each step in the gain table is 1/2 dB.
- *
- *     For example, if factory measured txpower is 16 dBm, and target txpower
- *     is 13 dBm, add 6 steps to the factory gain index to reduce txpower
- *     by 3 dB.
- *
- *
- * 6)  Find difference between current device temperature and (interpolated)
- *     factory-measured temperature for sub-band.  Factory values are in
- *     degrees Celsius.  To calculate current temperature, see comments for
- *     "4965 temperature calculation".
- *
- *     If current temperature is higher than factory temperature, driver must
- *     increase gain (lower gain table index), and vice verse.
- *
- *     Temperature affects gain differently for different channels:
- *
- *     2.4 GHz all channels:  3.5 degrees per half-dB step
- *     5 GHz channels 34-43:  4.5 degrees per half-dB step
- *     5 GHz channels >= 44:  4.0 degrees per half-dB step
- *
- *     NOTE:  Temperature can increase rapidly when transmitting, especially
- *            with heavy traffic at high txpowers.  Driver should update
- *            temperature calculations often under these conditions to
- *            maintain strong txpower in the face of rising temperature.
- *
- *
- * 7)  Find difference between current power supply voltage indicator
- *     (from "initialize alive") and factory-measured power supply voltage
- *     indicator (EEPROM).
- *
- *     If the current voltage is higher (indicator is lower) than factory
- *     voltage, gain should be reduced (gain table index increased) by:
- *
- *     (eeprom - current) / 7
- *
- *     If the current voltage is lower (indicator is higher) than factory
- *     voltage, gain should be increased (gain table index decreased) by:
- *
- *     2 * (current - eeprom) / 7
- *
- *     If number of index steps in either direction turns out to be > 2,
- *     something is wrong ... just use 0.
- *
- *     NOTE:  Voltage compensation is independent of band/channel.
- *
- *     NOTE:  "Initialize" uCode measures current voltage, which is assumed
- *            to be constant after this initial measurement.  Voltage
- *            compensation for txpower (number of steps in gain table)
- *            may be calculated once and used until the next uCode bootload.
- *
- *
- * 8)  If setting up txpowers for MIMO rates (rate indexes 8-15, 24-31),
- *     adjust txpower for each transmitter chain, so txpower is balanced
- *     between the two chains.  There are 5 pairs of tx_atten[group][chain]
- *     values in "initialize alive", one pair for each of 5 channel ranges:
- *
- *     Group 0:  5 GHz channel 34-43
- *     Group 1:  5 GHz channel 44-70
- *     Group 2:  5 GHz channel 71-124
- *     Group 3:  5 GHz channel 125-200
- *     Group 4:  2.4 GHz all channels
- *
- *     Add the tx_atten[group][chain] value to the index for the target chain.
- *     The values are signed, but are in pairs of 0 and a non-negative number,
- *     so as to reduce gain (if necessary) of the "hotter" channel.  This
- *     avoids any need to double-check for regulatory compliance after
- *     this step.
- *
- *
- * 9)  If setting up for a CCK rate, lower the gain by adding a CCK compensation
- *     value to the index:
- *
- *     Hardware rev B:  9 steps (4.5 dB)
- *     Hardware rev C:  5 steps (2.5 dB)
- *
- *     Hardware rev for 4965 can be determined by reading CSR_HW_REV_WA_REG,
- *     bits [3:2], 1 = B, 2 = C.
- *
- *     NOTE:  This compensation is in addition to any saturation backoff that
- *            might have been applied in an earlier step.
- *
- *
- * 10) Select the gain table, based on band (2.4 vs 5 GHz).
- *
- *     Limit the adjusted index to stay within the table!
- *
- *
- * 11) Read gain table entries for DSP and radio gain, place into appropriate
- *     location(s) in command (struct iwl4965_txpowertable_cmd).
- */
-
-/**
- * When MIMO is used (2 transmitters operating simultaneously), driver should
- * limit each transmitter to deliver a max of 3 dB below the regulatory limit
- * for the device.  That is, use half power for each transmitter, so total
- * txpower is within regulatory limits.
- *
- * The value "6" represents number of steps in gain table to reduce power 3 dB.
- * Each step is 1/2 dB.
- */
-#define IWL_TX_POWER_MIMO_REGULATORY_COMPENSATION (6)
-
-/**
- * CCK gain compensation.
- *
- * When calculating txpowers for CCK, after making sure that the target power
- * is within regulatory and saturation limits, driver must additionally
- * back off gain by adding these values to the gain table index.
- *
- * Hardware rev for 4965 can be determined by reading CSR_HW_REV_WA_REG,
- * bits [3:2], 1 = B, 2 = C.
- */
-#define IWL_TX_POWER_CCK_COMPENSATION_B_STEP (9)
-#define IWL_TX_POWER_CCK_COMPENSATION_C_STEP (5)
-
-/*
- * 4965 power supply voltage compensation for txpower
- */
-#define TX_POWER_IWL_VOLTAGE_CODES_PER_03V   (7)
-
-/**
- * Gain tables.
- *
- * The following tables contain pair of values for setting txpower, i.e.
- * gain settings for the output of the device's digital signal processor (DSP),
- * and for the analog gain structure of the transmitter.
- *
- * Each entry in the gain tables represents a step of 1/2 dB.  Note that these
- * are *relative* steps, not indications of absolute output power.  Output
- * power varies with temperature, voltage, and channel frequency, and also
- * requires consideration of average power (to satisfy regulatory constraints),
- * and peak power (to avoid distortion of the output signal).
- *
- * Each entry contains two values:
- * 1)  DSP gain (or sometimes called DSP attenuation).  This is a fine-grained
- *     linear value that multiplies the output of the digital signal processor,
- *     before being sent to the analog radio.
- * 2)  Radio gain.  This sets the analog gain of the radio Tx path.
- *     It is a coarser setting, and behaves in a logarithmic (dB) fashion.
- *
- * EEPROM contains factory calibration data for txpower.  This maps actual
- * measured txpower levels to gain settings in the "well known" tables
- * below ("well-known" means here that both factory calibration *and* the
- * driver work with the same table).
- *
- * There are separate tables for 2.4 GHz and 5 GHz bands.  The 5 GHz table
- * has an extension (into negative indexes), in case the driver needs to
- * boost power setting for high device temperatures (higher than would be
- * present during factory calibration).  A 5 Ghz EEPROM index of "40"
- * corresponds to the 49th entry in the table used by the driver.
- */
-#define MIN_TX_GAIN_INDEX		(0)  /* highest gain, lowest idx, 2.4 */
-#define MIN_TX_GAIN_INDEX_52GHZ_EXT	(-9) /* highest gain, lowest idx, 5 */
-
-/**
- * 2.4 GHz gain table
- *
- * Index    Dsp gain   Radio gain
- *   0        110         0x3f      (highest gain)
- *   1        104         0x3f
- *   2         98         0x3f
- *   3        110         0x3e
- *   4        104         0x3e
- *   5         98         0x3e
- *   6        110         0x3d
- *   7        104         0x3d
- *   8         98         0x3d
- *   9        110         0x3c
- *  10        104         0x3c
- *  11         98         0x3c
- *  12        110         0x3b
- *  13        104         0x3b
- *  14         98         0x3b
- *  15        110         0x3a
- *  16        104         0x3a
- *  17         98         0x3a
- *  18        110         0x39
- *  19        104         0x39
- *  20         98         0x39
- *  21        110         0x38
- *  22        104         0x38
- *  23         98         0x38
- *  24        110         0x37
- *  25        104         0x37
- *  26         98         0x37
- *  27        110         0x36
- *  28        104         0x36
- *  29         98         0x36
- *  30        110         0x35
- *  31        104         0x35
- *  32         98         0x35
- *  33        110         0x34
- *  34        104         0x34
- *  35         98         0x34
- *  36        110         0x33
- *  37        104         0x33
- *  38         98         0x33
- *  39        110         0x32
- *  40        104         0x32
- *  41         98         0x32
- *  42        110         0x31
- *  43        104         0x31
- *  44         98         0x31
- *  45        110         0x30
- *  46        104         0x30
- *  47         98         0x30
- *  48        110          0x6
- *  49        104          0x6
- *  50         98          0x6
- *  51        110          0x5
- *  52        104          0x5
- *  53         98          0x5
- *  54        110          0x4
- *  55        104          0x4
- *  56         98          0x4
- *  57        110          0x3
- *  58        104          0x3
- *  59         98          0x3
- *  60        110          0x2
- *  61        104          0x2
- *  62         98          0x2
- *  63        110          0x1
- *  64        104          0x1
- *  65         98          0x1
- *  66        110          0x0
- *  67        104          0x0
- *  68         98          0x0
- *  69         97            0
- *  70         96            0
- *  71         95            0
- *  72         94            0
- *  73         93            0
- *  74         92            0
- *  75         91            0
- *  76         90            0
- *  77         89            0
- *  78         88            0
- *  79         87            0
- *  80         86            0
- *  81         85            0
- *  82         84            0
- *  83         83            0
- *  84         82            0
- *  85         81            0
- *  86         80            0
- *  87         79            0
- *  88         78            0
- *  89         77            0
- *  90         76            0
- *  91         75            0
- *  92         74            0
- *  93         73            0
- *  94         72            0
- *  95         71            0
- *  96         70            0
- *  97         69            0
- *  98         68            0
- */
-
-/**
- * 5 GHz gain table
- *
- * Index    Dsp gain   Radio gain
- *  -9 	      123         0x3F      (highest gain)
- *  -8 	      117         0x3F
- *  -7        110         0x3F
- *  -6        104         0x3F
- *  -5         98         0x3F
- *  -4        110         0x3E
- *  -3        104         0x3E
- *  -2         98         0x3E
- *  -1        110         0x3D
- *   0        104         0x3D
- *   1         98         0x3D
- *   2        110         0x3C
- *   3        104         0x3C
- *   4         98         0x3C
- *   5        110         0x3B
- *   6        104         0x3B
- *   7         98         0x3B
- *   8        110         0x3A
- *   9        104         0x3A
- *  10         98         0x3A
- *  11        110         0x39
- *  12        104         0x39
- *  13         98         0x39
- *  14        110         0x38
- *  15        104         0x38
- *  16         98         0x38
- *  17        110         0x37
- *  18        104         0x37
- *  19         98         0x37
- *  20        110         0x36
- *  21        104         0x36
- *  22         98         0x36
- *  23        110         0x35
- *  24        104         0x35
- *  25         98         0x35
- *  26        110         0x34
- *  27        104         0x34
- *  28         98         0x34
- *  29        110         0x33
- *  30        104         0x33
- *  31         98         0x33
- *  32        110         0x32
- *  33        104         0x32
- *  34         98         0x32
- *  35        110         0x31
- *  36        104         0x31
- *  37         98         0x31
- *  38        110         0x30
- *  39        104         0x30
- *  40         98         0x30
- *  41        110         0x25
- *  42        104         0x25
- *  43         98         0x25
- *  44        110         0x24
- *  45        104         0x24
- *  46         98         0x24
- *  47        110         0x23
- *  48        104         0x23
- *  49         98         0x23
- *  50        110         0x22
- *  51        104         0x18
- *  52         98         0x18
- *  53        110         0x17
- *  54        104         0x17
- *  55         98         0x17
- *  56        110         0x16
- *  57        104         0x16
- *  58         98         0x16
- *  59        110         0x15
- *  60        104         0x15
- *  61         98         0x15
- *  62        110         0x14
- *  63        104         0x14
- *  64         98         0x14
- *  65        110         0x13
- *  66        104         0x13
- *  67         98         0x13
- *  68        110         0x12
- *  69        104         0x08
- *  70         98         0x08
- *  71        110         0x07
- *  72        104         0x07
- *  73         98         0x07
- *  74        110         0x06
- *  75        104         0x06
- *  76         98         0x06
- *  77        110         0x05
- *  78        104         0x05
- *  79         98         0x05
- *  80        110         0x04
- *  81        104         0x04
- *  82         98         0x04
- *  83        110         0x03
- *  84        104         0x03
- *  85         98         0x03
- *  86        110         0x02
- *  87        104         0x02
- *  88         98         0x02
- *  89        110         0x01
- *  90        104         0x01
- *  91         98         0x01
- *  92        110         0x00
- *  93        104         0x00
- *  94         98         0x00
- *  95         93         0x00
- *  96         88         0x00
- *  97         83         0x00
- *  98         78         0x00
- */
-
-
-/**
- * Sanity checks and default values for EEPROM regulatory levels.
- * If EEPROM values fall outside MIN/MAX range, use default values.
- *
- * Regulatory limits refer to the maximum average txpower allowed by
- * regulatory agencies in the geographies in which the device is meant
- * to be operated.  These limits are SKU-specific (i.e. geography-specific),
- * and channel-specific; each channel has an individual regulatory limit
- * listed in the EEPROM.
- *
- * Units are in half-dBm (i.e. "34" means 17 dBm).
- */
-#define IWL_TX_POWER_DEFAULT_REGULATORY_24   (34)
-#define IWL_TX_POWER_DEFAULT_REGULATORY_52   (34)
-#define IWL_TX_POWER_REGULATORY_MIN          (0)
-#define IWL_TX_POWER_REGULATORY_MAX          (34)
-
-/**
- * Sanity checks and default values for EEPROM saturation levels.
- * If EEPROM values fall outside MIN/MAX range, use default values.
- *
- * Saturation is the highest level that the output power amplifier can produce
- * without significant clipping distortion.  This is a "peak" power level.
- * Different types of modulation (i.e. various "rates", and OFDM vs. CCK)
- * require differing amounts of backoff, relative to their average power output,
- * in order to avoid clipping distortion.
- *
- * Driver must make sure that it is violating neither the saturation limit,
- * nor the regulatory limit, when calculating Tx power settings for various
- * rates.
- *
- * Units are in half-dBm (i.e. "38" means 19 dBm).
- */
-#define IWL_TX_POWER_DEFAULT_SATURATION_24   (38)
-#define IWL_TX_POWER_DEFAULT_SATURATION_52   (38)
-#define IWL_TX_POWER_SATURATION_MIN          (20)
-#define IWL_TX_POWER_SATURATION_MAX          (50)
-
-/**
- * Channel groups used for Tx Attenuation calibration (MIMO tx channel balance)
- * and thermal Txpower calibration.
- *
- * When calculating txpower, driver must compensate for current device
- * temperature; higher temperature requires higher gain.  Driver must calculate
- * current temperature (see "4965 temperature calculation"), then compare vs.
- * factory calibration temperature in EEPROM; if current temperature is higher
- * than factory temperature, driver must *increase* gain by proportions shown
- * in table below.  If current temperature is lower than factory, driver must
- * *decrease* gain.
- *
- * Different frequency ranges require different compensation, as shown below.
- */
-/* Group 0, 5.2 GHz ch 34-43:  4.5 degrees per 1/2 dB. */
-#define CALIB_IWL_TX_ATTEN_GR1_FCH 34
-#define CALIB_IWL_TX_ATTEN_GR1_LCH 43
-
-/* Group 1, 5.3 GHz ch 44-70:  4.0 degrees per 1/2 dB. */
-#define CALIB_IWL_TX_ATTEN_GR2_FCH 44
-#define CALIB_IWL_TX_ATTEN_GR2_LCH 70
-
-/* Group 2, 5.5 GHz ch 71-124:  4.0 degrees per 1/2 dB. */
-#define CALIB_IWL_TX_ATTEN_GR3_FCH 71
-#define CALIB_IWL_TX_ATTEN_GR3_LCH 124
-
-/* Group 3, 5.7 GHz ch 125-200:  4.0 degrees per 1/2 dB. */
-#define CALIB_IWL_TX_ATTEN_GR4_FCH 125
-#define CALIB_IWL_TX_ATTEN_GR4_LCH 200
-
-/* Group 4, 2.4 GHz all channels:  3.5 degrees per 1/2 dB. */
-#define CALIB_IWL_TX_ATTEN_GR5_FCH 1
-#define CALIB_IWL_TX_ATTEN_GR5_LCH 20
-
-enum {
-	CALIB_CH_GROUP_1 = 0,
-	CALIB_CH_GROUP_2 = 1,
-	CALIB_CH_GROUP_3 = 2,
-	CALIB_CH_GROUP_4 = 3,
-	CALIB_CH_GROUP_5 = 4,
-	CALIB_CH_GROUP_MAX
-};
-
-/********************* END TXPOWER *****************************************/
-
-
-/**
- * Tx/Rx Queues
- *
- * Most communication between driver and 4965 is via queues of data buffers.
- * For example, all commands that the driver issues to device's embedded
- * controller (uCode) are via the command queue (one of the Tx queues).  All
- * uCode command responses/replies/notifications, including Rx frames, are
- * conveyed from uCode to driver via the Rx queue.
- *
- * Most support for these queues, including handshake support, resides in
- * structures in host DRAM, shared between the driver and the device.  When
- * allocating this memory, the driver must make sure that data written by
- * the host CPU updates DRAM immediately (and does not get "stuck" in CPU's
- * cache memory), so DRAM and cache are consistent, and the device can
- * immediately see changes made by the driver.
- *
- * 4965 supports up to 16 DRAM-based Tx queues, and services these queues via
- * up to 7 DMA channels (FIFOs).  Each Tx queue is supported by a circular array
- * in DRAM containing 256 Transmit Frame Descriptors (TFDs).
- */
-#define IWL49_NUM_FIFOS 	7
-#define IWL49_CMD_FIFO_NUM	4
-#define IWL49_NUM_QUEUES	16
-#define IWL49_NUM_AMPDU_QUEUES	8
-
-
-/**
- * struct iwl4965_schedq_bc_tbl
- *
- * Byte Count table
- *
- * Each Tx queue uses a byte-count table containing 320 entries:
- * one 16-bit entry for each of 256 TFDs, plus an additional 64 entries that
- * duplicate the first 64 entries (to avoid wrap-around within a Tx window;
- * max Tx window is 64 TFDs).
- *
- * When driver sets up a new TFD, it must also enter the total byte count
- * of the frame to be transmitted into the corresponding entry in the byte
- * count table for the chosen Tx queue.  If the TFD index is 0-63, the driver
- * must duplicate the byte count entry in corresponding index 256-319.
- *
- * padding puts each byte count table on a 1024-byte boundary;
- * 4965 assumes tables are separated by 1024 bytes.
- */
-struct iwl4965_scd_bc_tbl {
-	__le16 tfd_offset[TFD_QUEUE_BC_SIZE];
-	u8 pad[1024 - (TFD_QUEUE_BC_SIZE) * sizeof(__le16)];
-} __packed;
-
-#endif /* !__iwl_4965_hw_h__ */