ath10k: fix block comments style

Fix output from checkpatch.pl like:
 Block comments use a trailing */ on a separate lin

Signed-off-by: Marcin Rokicki <marcin.rokicki@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>

1 files changed, 27 insertions, 16 deletions

diff --git a/drivers/net/wireless/ath/ath10k/mac.c b/drivers/net/wireless/ath/ath10k/mac.c
index ddabec8022f4..9dc06832b7f1 100644
--- a/drivers/net/wireless/ath/ath10k/mac.c
+++ b/drivers/net/wireless/ath/ath10k/mac.c
@@ -457,7 +457,8 @@ static int ath10k_clear_vdev_key(struct ath10k_vif *arvif,
 
 	for (;;) {
 		/* since ath10k_install_key we can't hold data_lock all the
-		 * time, so we try to remove the keys incrementally */
+		 * time, so we try to remove the keys incrementally
+		 */
 		spin_lock_bh(&ar->data_lock);
 		i = 0;
 		list_for_each_entry(peer, &ar->peers, list) {
@@ -609,7 +610,8 @@ static u8 ath10k_parse_mpdudensity(u8 mpdudensity)
 	case 2:
 	case 3:
 	/* Our lower layer calculations limit our precision to
-	   1 microsecond */
+	 * 1 microsecond
+	 */
 		return 1;
 	case 4:
 		return 2;
@@ -978,7 +980,8 @@ static int ath10k_monitor_vdev_start(struct ath10k *ar, int vdev_id)
 	arg.channel.band_center_freq2 = chandef->center_freq2;
 
 	/* TODO setup this dynamically, what in case we
-	   don't have any vifs? */
+	 * don't have any vifs?
+	 */
 	arg.channel.mode = chan_to_phymode(chandef);
 	arg.channel.chan_radar =
 			!!(channel->flags & IEEE80211_CHAN_RADAR);
@@ -2373,9 +2376,10 @@ static int ath10k_peer_assoc_qos_ap(struct ath10k *ar,
 		}
 
 		/* TODO setup this based on STA listen interval and
-		   beacon interval. Currently we don't know
-		   sta->listen_interval - mac80211 patch required.
-		   Currently use 10 seconds */
+		 * beacon interval. Currently we don't know
+		 * sta->listen_interval - mac80211 patch required.
+		 * Currently use 10 seconds
+		 */
 		ret = ath10k_wmi_set_ap_ps_param(ar, arvif->vdev_id, sta->addr,
 						 WMI_AP_PS_PEER_PARAM_AGEOUT_TIME,
 						 10);
@@ -2480,7 +2484,8 @@ static void ath10k_peer_assoc_h_vht(struct ath10k *ar,
 	/* Workaround: Some Netgear/Linksys 11ac APs set Rx A-MPDU factor to
 	 * zero in VHT IE. Using it would result in degraded throughput.
 	 * arg->peer_max_mpdu at this point contains HT max_mpdu so keep
-	 * it if VHT max_mpdu is smaller. */
+	 * it if VHT max_mpdu is smaller.
+	 */
 	arg->peer_max_mpdu = max(arg->peer_max_mpdu,
 				 (1U << (IEEE80211_HT_MAX_AMPDU_FACTOR +
 					ampdu_factor)) - 1);
@@ -2793,7 +2798,8 @@ static void ath10k_bss_assoc(struct ieee80211_hw *hw,
 	}
 
 	/* ap_sta must be accessed only within rcu section which must be left
-	 * before calling ath10k_setup_peer_smps() which might sleep. */
+	 * before calling ath10k_setup_peer_smps() which might sleep.
+	 */
 	ht_cap = ap_sta->ht_cap;
 	vht_cap = ap_sta->vht_cap;
 
@@ -3064,7 +3070,8 @@ static int ath10k_update_channel_list(struct ath10k *ar)
 
 			/* FIXME: why use only legacy modes, why not any
 			 * HT/VHT modes? Would that even make any
-			 * difference? */
+			 * difference?
+			 */
 			if (channel->band == NL80211_BAND_2GHZ)
 				ch->mode = MODE_11G;
 			else
@@ -3128,7 +3135,8 @@ static void ath10k_regd_update(struct ath10k *ar)
 	}
 
 	/* Target allows setting up per-band regdomain but ath_common provides
-	 * a combined one only */
+	 * a combined one only
+	 */
 	ret = ath10k_wmi_pdev_set_regdomain(ar,
 					    regpair->reg_domain,
 					    regpair->reg_domain, /* 2ghz */
@@ -3677,7 +3685,8 @@ void ath10k_offchan_tx_work(struct work_struct *work)
 	 * never transmitted. We delete the peer upon tx completion.
 	 * It is unlikely that a peer for offchannel tx will already be
 	 * present. However it may be in some rare cases so account for that.
-	 * Otherwise we might remove a legitimate peer and break stuff. */
+	 * Otherwise we might remove a legitimate peer and break stuff.
+	 */
 
 	for (;;) {
 		skb = skb_dequeue(&ar->offchan_tx_queue);
@@ -5717,7 +5726,8 @@ static int ath10k_set_key(struct ieee80211_hw *hw, enum set_key_cmd cmd,
 	}
 
 	/* the peer should not disappear in mid-way (unless FW goes awry) since
-	 * we already hold conf_mutex. we just make sure its there now. */
+	 * we already hold conf_mutex. we just make sure its there now.
+	 */
 	spin_lock_bh(&ar->data_lock);
 	peer = ath10k_peer_find(ar, arvif->vdev_id, peer_addr);
 	spin_unlock_bh(&ar->data_lock);
@@ -5729,8 +5739,7 @@ static int ath10k_set_key(struct ieee80211_hw *hw, enum set_key_cmd cmd,
 			ret = -EOPNOTSUPP;
 			goto exit;
 		} else {
-			/* if the peer doesn't exist there is no key to disable
-			 * anymore */
+			/* if the peer doesn't exist there is no key to disable anymore */
 			goto exit;
 		}
 	}
@@ -6589,7 +6598,8 @@ static void ath10k_flush(struct ieee80211_hw *hw, struct ieee80211_vif *vif,
 	long time_left;
 
 	/* mac80211 doesn't care if we really xmit queued frames or not
-	 * we'll collect those frames either way if we stop/delete vdevs */
+	 * we'll collect those frames either way if we stop/delete vdevs
+	 */
 	if (drop)
 		return;
 
@@ -6640,7 +6650,8 @@ static void ath10k_reconfig_complete(struct ieee80211_hw *hw,
 	mutex_lock(&ar->conf_mutex);
 
 	/* If device failed to restart it will be in a different state, e.g.
-	 * ATH10K_STATE_WEDGED */
+	 * ATH10K_STATE_WEDGED
+	 */
 	if (ar->state == ATH10K_STATE_RESTARTED) {
 		ath10k_info(ar, "device successfully recovered\n");
 		ar->state = ATH10K_STATE_ON;