Merge git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-next-2.6

* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-next-2.6: (1429 commits)
  net: Allow dependancies of FDDI & Tokenring to be modular.
  igb: Fix build warning when DCA is disabled.
  net: Fix warning fallout from recent NAPI interface changes.
  gro: Fix potential use after free
  sfc: If AN is enabled, always read speed/duplex from the AN advertising bits
  sfc: When disabling the NIC, close the device rather than unregistering it
  sfc: SFT9001: Add cable diagnostics
  sfc: Add support for multiple PHY self-tests
  sfc: Merge top-level functions for self-tests
  sfc: Clean up PHY mode management in loopback self-test
  sfc: Fix unreliable link detection in some loopback modes
  sfc: Generate unique names for per-NIC workqueues
  802.3ad: use standard ethhdr instead of ad_header
  802.3ad: generalize out mac address initializer
  802.3ad: initialize ports LACPDU from const initializer
  802.3ad: remove typedef around ad_system
  802.3ad: turn ports is_individual into a bool
  802.3ad: turn ports is_enabled into a bool
  802.3ad: make ntt bool
  ixgbe: Fix set_ringparam in ixgbe to use the same memory pools.
  ...

Fixed trivial IPv4/6 address printing conflicts in fs/cifs/connect.c due
to the conversion to %pI (in this networking merge) and the addition of
doing IPv6 addresses (from the earlier merge of CIFS).

12 files changed, 999 insertions, 274 deletions

diff --git a/drivers/net/phy/Kconfig b/drivers/net/phy/Kconfig
index d55932acd887..de9cf5136fdc 100644
--- a/drivers/net/phy/Kconfig
+++ b/drivers/net/phy/Kconfig
@@ -66,6 +66,22 @@ config REALTEK_PHY
 	---help---
 	  Supports the Realtek 821x PHY.
 
+config NATIONAL_PHY
+	tristate "Drivers for National Semiconductor PHYs"
+	---help---
+	  Currently supports the DP83865 PHY.
+
+config STE10XP
+	depends on PHYLIB
+	tristate "Driver for STMicroelectronics STe10Xp PHYs"
+	---help---
+	  This is the driver for the STe100p and STe101p PHYs.
+
+config LSI_ET1011C_PHY
+	tristate "Driver for LSI ET1011C PHY"
+	---help---
+	  Supports the LSI ET1011C PHY.
+
 config FIXED_PHY
 	bool "Driver for MDIO Bus/PHY emulation with fixed speed/link PHYs"
 	depends on PHYLIB=y
@@ -84,10 +100,13 @@ config MDIO_BITBANG
 
 	  If in doubt, say N.
 
-config MDIO_OF_GPIO
+config MDIO_GPIO
 	tristate "Support for GPIO lib-based bitbanged MDIO buses"
-	depends on MDIO_BITBANG && OF_GPIO
+	depends on MDIO_BITBANG && GENERIC_GPIO
 	---help---
 	  Supports GPIO lib-based MDIO busses.
 
+	  To compile this driver as a module, choose M here: the module
+	  will be called mdio-gpio.
+
 endif # PHYLIB
diff --git a/drivers/net/phy/Makefile b/drivers/net/phy/Makefile
index eee329fa6f53..3a1bfefefbc3 100644
--- a/drivers/net/phy/Makefile
+++ b/drivers/net/phy/Makefile
@@ -13,6 +13,9 @@ obj-$(CONFIG_VITESSE_PHY)	+= vitesse.o
 obj-$(CONFIG_BROADCOM_PHY)	+= broadcom.o
 obj-$(CONFIG_ICPLUS_PHY)	+= icplus.o
 obj-$(CONFIG_REALTEK_PHY)	+= realtek.o
+obj-$(CONFIG_LSI_ET1011C_PHY)	+= et1011c.o
 obj-$(CONFIG_FIXED_PHY)		+= fixed.o
 obj-$(CONFIG_MDIO_BITBANG)	+= mdio-bitbang.o
-obj-$(CONFIG_MDIO_OF_GPIO)	+= mdio-ofgpio.o
+obj-$(CONFIG_MDIO_GPIO)		+= mdio-gpio.o
+obj-$(CONFIG_NATIONAL_PHY)	+= national.o
+obj-$(CONFIG_STE10XP)		+= ste10Xp.o
diff --git a/drivers/net/phy/broadcom.c b/drivers/net/phy/broadcom.c
index 4b4dc98ad165..190efc3301c6 100644
--- a/drivers/net/phy/broadcom.c
+++ b/drivers/net/phy/broadcom.c
@@ -17,6 +17,8 @@
 #include <linux/module.h>
 #include <linux/phy.h>
 
+#define PHY_ID_BCM50610		0x0143bd60
+
 #define MII_BCM54XX_ECR		0x10	/* BCM54xx extended control register */
 #define MII_BCM54XX_ECR_IM	0x1000	/* Interrupt mask */
 #define MII_BCM54XX_ECR_IF	0x0800	/* Interrupt force */
@@ -54,6 +56,21 @@
 #define MII_BCM54XX_SHD_DATA(x)	((x & 0x3ff) << 0)
 
 /*
+ * AUXILIARY CONTROL SHADOW ACCESS REGISTERS.  (PHY REG 0x18)
+ */
+#define MII_BCM54XX_AUXCTL_SHDWSEL_AUXCTL	0x0000
+#define MII_BCM54XX_AUXCTL_ACTL_TX_6DB		0x0400
+#define MII_BCM54XX_AUXCTL_ACTL_SMDSP_ENA	0x0800
+
+#define MII_BCM54XX_AUXCTL_MISC_WREN	0x8000
+#define MII_BCM54XX_AUXCTL_MISC_FORCE_AMDIX	0x0200
+#define MII_BCM54XX_AUXCTL_MISC_RDSEL_MISC	0x7000
+#define MII_BCM54XX_AUXCTL_SHDWSEL_MISC	0x0007
+
+#define MII_BCM54XX_AUXCTL_SHDWSEL_AUXCTL	0x0000
+
+
+/*
  * Broadcom LED source encodings.  These are used in BCM5461, BCM5481,
  * BCM5482, and possibly some others.
  */
@@ -88,6 +105,24 @@
 #define BCM5482_SHD_MODE_1000BX	0x0001	/* Enable 1000BASE-X registers */
 
 /*
+ * EXPANSION SHADOW ACCESS REGISTERS.  (PHY REG 0x15, 0x16, and 0x17)
+ */
+#define MII_BCM54XX_EXP_AADJ1CH0		0x001f
+#define  MII_BCM54XX_EXP_AADJ1CH0_SWP_ABCD_OEN	0x0200
+#define  MII_BCM54XX_EXP_AADJ1CH0_SWSEL_THPF	0x0100
+#define MII_BCM54XX_EXP_AADJ1CH3		0x601f
+#define  MII_BCM54XX_EXP_AADJ1CH3_ADCCKADJ	0x0002
+#define MII_BCM54XX_EXP_EXP08			0x0F08
+#define  MII_BCM54XX_EXP_EXP08_RJCT_2MHZ	0x0001
+#define  MII_BCM54XX_EXP_EXP08_EARLY_DAC_WAKE	0x0200
+#define MII_BCM54XX_EXP_EXP75			0x0f75
+#define  MII_BCM54XX_EXP_EXP75_VDACCTRL		0x003c
+#define MII_BCM54XX_EXP_EXP96			0x0f96
+#define  MII_BCM54XX_EXP_EXP96_MYST		0x0010
+#define MII_BCM54XX_EXP_EXP97			0x0f97
+#define  MII_BCM54XX_EXP_EXP97_MYST		0x0c0c
+
+/*
  * BCM5482: Secondary SerDes registers
  */
 #define BCM5482_SSD_1000BX_CTL		0x00	/* 1000BASE-X Control */
@@ -128,40 +163,93 @@ static int bcm54xx_shadow_write(struct phy_device *phydev, u16 shadow, u16 val)
 			 MII_BCM54XX_SHD_DATA(val));
 }
 
-/*
- * Indirect register access functions for the Expansion Registers
- * and Secondary SerDes registers (when sec_serdes=1).
- */
-static int bcm54xx_exp_read(struct phy_device *phydev,
-			    int sec_serdes, u8 regnum)
+/* Indirect register access functions for the Expansion Registers */
+static int bcm54xx_exp_read(struct phy_device *phydev, u8 regnum)
 {
 	int val;
 
-	phy_write(phydev, MII_BCM54XX_EXP_SEL,
-		  (sec_serdes ? MII_BCM54XX_EXP_SEL_SSD :
-				MII_BCM54XX_EXP_SEL_ER) |
-		  regnum);
+	val = phy_write(phydev, MII_BCM54XX_EXP_SEL, regnum);
+	if (val < 0)
+		return val;
+
 	val = phy_read(phydev, MII_BCM54XX_EXP_DATA);
-	phy_write(phydev, MII_BCM54XX_EXP_SEL, regnum);
+
+	/* Restore default value.  It's O.K. if this write fails. */
+	phy_write(phydev, MII_BCM54XX_EXP_SEL, 0);
 
 	return val;
 }
 
-static int bcm54xx_exp_write(struct phy_device *phydev,
-			     int sec_serdes, u8 regnum, u16 val)
+static int bcm54xx_exp_write(struct phy_device *phydev, u16 regnum, u16 val)
 {
 	int ret;
 
-	phy_write(phydev, MII_BCM54XX_EXP_SEL,
-		  (sec_serdes ? MII_BCM54XX_EXP_SEL_SSD :
-				MII_BCM54XX_EXP_SEL_ER) |
-		  regnum);
+	ret = phy_write(phydev, MII_BCM54XX_EXP_SEL, regnum);
+	if (ret < 0)
+		return ret;
+
 	ret = phy_write(phydev, MII_BCM54XX_EXP_DATA, val);
-	phy_write(phydev, MII_BCM54XX_EXP_SEL, regnum);
+
+	/* Restore default value.  It's O.K. if this write fails. */
+	phy_write(phydev, MII_BCM54XX_EXP_SEL, 0);
 
 	return ret;
 }
 
+static int bcm54xx_auxctl_write(struct phy_device *phydev, u16 regnum, u16 val)
+{
+	return phy_write(phydev, MII_BCM54XX_AUX_CTL, regnum | val);
+}
+
+static int bcm50610_a0_workaround(struct phy_device *phydev)
+{
+	int err;
+
+	err = bcm54xx_auxctl_write(phydev,
+				   MII_BCM54XX_AUXCTL_SHDWSEL_AUXCTL,
+				   MII_BCM54XX_AUXCTL_ACTL_SMDSP_ENA |
+				   MII_BCM54XX_AUXCTL_ACTL_TX_6DB);
+	if (err < 0)
+		return err;
+
+	err = bcm54xx_exp_write(phydev, MII_BCM54XX_EXP_EXP08,
+				MII_BCM54XX_EXP_EXP08_RJCT_2MHZ	|
+				MII_BCM54XX_EXP_EXP08_EARLY_DAC_WAKE);
+	if (err < 0)
+		goto error;
+
+	err = bcm54xx_exp_write(phydev, MII_BCM54XX_EXP_AADJ1CH0,
+				MII_BCM54XX_EXP_AADJ1CH0_SWP_ABCD_OEN |
+				MII_BCM54XX_EXP_AADJ1CH0_SWSEL_THPF);
+	if (err < 0)
+		goto error;
+
+	err = bcm54xx_exp_write(phydev, MII_BCM54XX_EXP_AADJ1CH3,
+					MII_BCM54XX_EXP_AADJ1CH3_ADCCKADJ);
+	if (err < 0)
+		goto error;
+
+	err = bcm54xx_exp_write(phydev, MII_BCM54XX_EXP_EXP75,
+				MII_BCM54XX_EXP_EXP75_VDACCTRL);
+	if (err < 0)
+		goto error;
+
+	err = bcm54xx_exp_write(phydev, MII_BCM54XX_EXP_EXP96,
+				MII_BCM54XX_EXP_EXP96_MYST);
+	if (err < 0)
+		goto error;
+
+	err = bcm54xx_exp_write(phydev, MII_BCM54XX_EXP_EXP97,
+				MII_BCM54XX_EXP_EXP97_MYST);
+
+error:
+	bcm54xx_auxctl_write(phydev,
+			     MII_BCM54XX_AUXCTL_SHDWSEL_AUXCTL,
+			     MII_BCM54XX_AUXCTL_ACTL_TX_6DB);
+
+	return err;
+}
+
 static int bcm54xx_config_init(struct phy_device *phydev)
 {
 	int reg, err;
@@ -183,6 +271,13 @@ static int bcm54xx_config_init(struct phy_device *phydev)
 	err = phy_write(phydev, MII_BCM54XX_IMR, reg);
 	if (err < 0)
 		return err;
+
+	if (phydev->drv->phy_id == PHY_ID_BCM50610) {
+		err = bcm50610_a0_workaround(phydev);
+		if (err < 0)
+			return err;
+	}
+
 	return 0;
 }
 
@@ -205,18 +300,27 @@ static int bcm5482_config_init(struct phy_device *phydev)
 		/*
 		 * Enable SGMII slave mode and auto-detection
 		 */
-		reg = bcm54xx_exp_read(phydev, 1, BCM5482_SSD_SGMII_SLAVE);
-		bcm54xx_exp_write(phydev, 1, BCM5482_SSD_SGMII_SLAVE,
-				  reg |
-				  BCM5482_SSD_SGMII_SLAVE_EN |
-				  BCM5482_SSD_SGMII_SLAVE_AD);
+		reg = BCM5482_SSD_SGMII_SLAVE | MII_BCM54XX_EXP_SEL_SSD;
+		err = bcm54xx_exp_read(phydev, reg);
+		if (err < 0)
+			return err;
+		err = bcm54xx_exp_write(phydev, reg, err |
+					BCM5482_SSD_SGMII_SLAVE_EN |
+					BCM5482_SSD_SGMII_SLAVE_AD);
+		if (err < 0)
+			return err;
 
 		/*
 		 * Disable secondary SerDes powerdown
 		 */
-		reg = bcm54xx_exp_read(phydev, 1, BCM5482_SSD_1000BX_CTL);
-		bcm54xx_exp_write(phydev, 1, BCM5482_SSD_1000BX_CTL,
-				  reg & ~BCM5482_SSD_1000BX_CTL_PWRDOWN);
+		reg = BCM5482_SSD_1000BX_CTL | MII_BCM54XX_EXP_SEL_SSD;
+		err = bcm54xx_exp_read(phydev, reg);
+		if (err < 0)
+			return err;
+		err = bcm54xx_exp_write(phydev, reg,
+					err & ~BCM5482_SSD_1000BX_CTL_PWRDOWN);
+		if (err < 0)
+			return err;
 
 		/*
 		 * Select 1000BASE-X register set (primary SerDes)
@@ -335,7 +439,8 @@ static struct phy_driver bcm5411_driver = {
 	.phy_id		= 0x00206070,
 	.phy_id_mask	= 0xfffffff0,
 	.name		= "Broadcom BCM5411",
-	.features	= PHY_GBIT_FEATURES,
+	.features	= PHY_GBIT_FEATURES |
+			  SUPPORTED_Pause | SUPPORTED_Asym_Pause,
 	.flags		= PHY_HAS_MAGICANEG | PHY_HAS_INTERRUPT,
 	.config_init	= bcm54xx_config_init,
 	.config_aneg	= genphy_config_aneg,
@@ -349,7 +454,8 @@ static struct phy_driver bcm5421_driver = {
 	.phy_id		= 0x002060e0,
 	.phy_id_mask	= 0xfffffff0,
 	.name		= "Broadcom BCM5421",
-	.features	= PHY_GBIT_FEATURES,
+	.features	= PHY_GBIT_FEATURES |
+			  SUPPORTED_Pause | SUPPORTED_Asym_Pause,
 	.flags		= PHY_HAS_MAGICANEG | PHY_HAS_INTERRUPT,
 	.config_init	= bcm54xx_config_init,
 	.config_aneg	= genphy_config_aneg,
@@ -363,7 +469,8 @@ static struct phy_driver bcm5461_driver = {
 	.phy_id		= 0x002060c0,
 	.phy_id_mask	= 0xfffffff0,
 	.name		= "Broadcom BCM5461",
-	.features	= PHY_GBIT_FEATURES,
+	.features	= PHY_GBIT_FEATURES |
+			  SUPPORTED_Pause | SUPPORTED_Asym_Pause,
 	.flags		= PHY_HAS_MAGICANEG | PHY_HAS_INTERRUPT,
 	.config_init	= bcm54xx_config_init,
 	.config_aneg	= genphy_config_aneg,
@@ -377,7 +484,8 @@ static struct phy_driver bcm5464_driver = {
 	.phy_id		= 0x002060b0,
 	.phy_id_mask	= 0xfffffff0,
 	.name		= "Broadcom BCM5464",
-	.features	= PHY_GBIT_FEATURES,
+	.features	= PHY_GBIT_FEATURES |
+			  SUPPORTED_Pause | SUPPORTED_Asym_Pause,
 	.flags		= PHY_HAS_MAGICANEG | PHY_HAS_INTERRUPT,
 	.config_init	= bcm54xx_config_init,
 	.config_aneg	= genphy_config_aneg,
@@ -391,7 +499,8 @@ static struct phy_driver bcm5481_driver = {
 	.phy_id		= 0x0143bca0,
 	.phy_id_mask	= 0xfffffff0,
 	.name		= "Broadcom BCM5481",
-	.features	= PHY_GBIT_FEATURES,
+	.features	= PHY_GBIT_FEATURES |
+			  SUPPORTED_Pause | SUPPORTED_Asym_Pause,
 	.flags		= PHY_HAS_MAGICANEG | PHY_HAS_INTERRUPT,
 	.config_init	= bcm54xx_config_init,
 	.config_aneg	= bcm5481_config_aneg,
@@ -405,7 +514,8 @@ static struct phy_driver bcm5482_driver = {
 	.phy_id		= 0x0143bcb0,
 	.phy_id_mask	= 0xfffffff0,
 	.name		= "Broadcom BCM5482",
-	.features	= PHY_GBIT_FEATURES,
+	.features	= PHY_GBIT_FEATURES |
+			  SUPPORTED_Pause | SUPPORTED_Asym_Pause,
 	.flags		= PHY_HAS_MAGICANEG | PHY_HAS_INTERRUPT,
 	.config_init	= bcm5482_config_init,
 	.config_aneg	= genphy_config_aneg,
@@ -415,6 +525,36 @@ static struct phy_driver bcm5482_driver = {
 	.driver 	= { .owner = THIS_MODULE },
 };
 
+static struct phy_driver bcm50610_driver = {
+	.phy_id		= PHY_ID_BCM50610,
+	.phy_id_mask	= 0xfffffff0,
+	.name		= "Broadcom BCM50610",
+	.features	= PHY_GBIT_FEATURES |
+			  SUPPORTED_Pause | SUPPORTED_Asym_Pause,
+	.flags		= PHY_HAS_MAGICANEG | PHY_HAS_INTERRUPT,
+	.config_init	= bcm54xx_config_init,
+	.config_aneg	= genphy_config_aneg,
+	.read_status	= genphy_read_status,
+	.ack_interrupt	= bcm54xx_ack_interrupt,
+	.config_intr	= bcm54xx_config_intr,
+	.driver 	= { .owner = THIS_MODULE },
+};
+
+static struct phy_driver bcm57780_driver = {
+	.phy_id		= 0x03625d90,
+	.phy_id_mask	= 0xfffffff0,
+	.name		= "Broadcom BCM57780",
+	.features	= PHY_GBIT_FEATURES |
+			  SUPPORTED_Pause | SUPPORTED_Asym_Pause,
+	.flags		= PHY_HAS_MAGICANEG | PHY_HAS_INTERRUPT,
+	.config_init	= bcm54xx_config_init,
+	.config_aneg	= genphy_config_aneg,
+	.read_status	= genphy_read_status,
+	.ack_interrupt	= bcm54xx_ack_interrupt,
+	.config_intr	= bcm54xx_config_intr,
+	.driver 	= { .owner = THIS_MODULE },
+};
+
 static int __init broadcom_init(void)
 {
 	int ret;
@@ -437,8 +577,18 @@ static int __init broadcom_init(void)
 	ret = phy_driver_register(&bcm5482_driver);
 	if (ret)
 		goto out_5482;
+	ret = phy_driver_register(&bcm50610_driver);
+	if (ret)
+		goto out_50610;
+	ret = phy_driver_register(&bcm57780_driver);
+	if (ret)
+		goto out_57780;
 	return ret;
 
+out_57780:
+	phy_driver_unregister(&bcm50610_driver);
+out_50610:
+	phy_driver_unregister(&bcm5482_driver);
 out_5482:
 	phy_driver_unregister(&bcm5481_driver);
 out_5481:
@@ -455,6 +605,8 @@ out_5411:
 
 static void __exit broadcom_exit(void)
 {
+	phy_driver_unregister(&bcm57780_driver);
+	phy_driver_unregister(&bcm50610_driver);
 	phy_driver_unregister(&bcm5482_driver);
 	phy_driver_unregister(&bcm5481_driver);
 	phy_driver_unregister(&bcm5464_driver);
diff --git a/drivers/net/phy/et1011c.c b/drivers/net/phy/et1011c.c
new file mode 100644
index 000000000000..b031fa21f1aa
--- /dev/null
+++ b/drivers/net/phy/et1011c.c
@@ -0,0 +1,113 @@
+/*
+ * drivers/net/phy/et1011c.c
+ *
+ * Driver for LSI ET1011C PHYs
+ *
+ * Author: Chaithrika U S
+ *
+ * Copyright (c) 2008 Texas Instruments
+ *
+ * This program is free software; you can redistribute  it and/or modify it
+ * under  the terms of  the GNU General  Public License as published by the
+ * Free Software Foundation;  either version 2 of the  License, or (at your
+ * option) any later version.
+ *
+ */
+#include <linux/kernel.h>
+#include <linux/string.h>
+#include <linux/errno.h>
+#include <linux/unistd.h>
+#include <linux/slab.h>
+#include <linux/interrupt.h>
+#include <linux/init.h>
+#include <linux/delay.h>
+#include <linux/netdevice.h>
+#include <linux/etherdevice.h>
+#include <linux/skbuff.h>
+#include <linux/spinlock.h>
+#include <linux/mm.h>
+#include <linux/module.h>
+#include <linux/mii.h>
+#include <linux/ethtool.h>
+#include <linux/phy.h>
+#include <linux/io.h>
+#include <linux/uaccess.h>
+#include <asm/irq.h>
+
+#define ET1011C_STATUS_REG	(0x1A)
+#define ET1011C_CONFIG_REG	(0x16)
+#define ET1011C_SPEED_MASK		(0x0300)
+#define ET1011C_GIGABIT_SPEED		(0x0200)
+#define ET1011C_TX_FIFO_MASK		(0x3000)
+#define ET1011C_TX_FIFO_DEPTH_8		(0x0000)
+#define ET1011C_TX_FIFO_DEPTH_16	(0x1000)
+#define ET1011C_INTERFACE_MASK		(0x0007)
+#define ET1011C_GMII_INTERFACE		(0x0002)
+#define ET1011C_SYS_CLK_EN		(0x01 << 4)
+
+
+MODULE_DESCRIPTION("LSI ET1011C PHY driver");
+MODULE_AUTHOR("Chaithrika U S");
+MODULE_LICENSE("GPL");
+
+static int et1011c_config_aneg(struct phy_device *phydev)
+{
+	int ctl = 0;
+	ctl = phy_read(phydev, MII_BMCR);
+	if (ctl < 0)
+		return ctl;
+	ctl &= ~(BMCR_FULLDPLX | BMCR_SPEED100 | BMCR_SPEED1000 |
+		 BMCR_ANENABLE);
+	/* First clear the PHY */
+	phy_write(phydev, MII_BMCR, ctl | BMCR_RESET);
+
+	return genphy_config_aneg(phydev);
+}
+
+static int et1011c_read_status(struct phy_device *phydev)
+{
+	int ret;
+	u32 val;
+	static int speed;
+	ret = genphy_read_status(phydev);
+
+	if (speed != phydev->speed) {
+		speed = phydev->speed;
+		val = phy_read(phydev, ET1011C_STATUS_REG);
+		if ((val & ET1011C_SPEED_MASK) ==
+					ET1011C_GIGABIT_SPEED) {
+			val = phy_read(phydev, ET1011C_CONFIG_REG);
+			val &= ~ET1011C_TX_FIFO_MASK;
+			phy_write(phydev, ET1011C_CONFIG_REG, val\
+					| ET1011C_GMII_INTERFACE\
+					| ET1011C_SYS_CLK_EN\
+					| ET1011C_TX_FIFO_DEPTH_16);
+
+		}
+	}
+	return ret;
+}
+
+static struct phy_driver et1011c_driver = {
+	.phy_id		= 0x0282f014,
+	.name		= "ET1011C",
+	.phy_id_mask	= 0xfffffff0,
+	.features	= (PHY_BASIC_FEATURES | SUPPORTED_1000baseT_Full),
+	.flags		= PHY_POLL,
+	.config_aneg	= et1011c_config_aneg,
+	.read_status	= et1011c_read_status,
+	.driver 	= { .owner = THIS_MODULE,},
+};
+
+static int __init et1011c_init(void)
+{
+	return phy_driver_register(&et1011c_driver);
+}
+
+static void __exit et1011c_exit(void)
+{
+	phy_driver_unregister(&et1011c_driver);
+}
+
+module_init(et1011c_init);
+module_exit(et1011c_exit);
diff --git a/drivers/net/phy/mdio-gpio.c b/drivers/net/phy/mdio-gpio.c
new file mode 100644
index 000000000000..a439ebeb4319
--- /dev/null
+++ b/drivers/net/phy/mdio-gpio.c
@@ -0,0 +1,296 @@
+/*
+ * GPIO based MDIO bitbang driver.
+ * Supports OpenFirmware.
+ *
+ * Copyright (c) 2008 CSE Semaphore Belgium.
+ *  by Laurent Pinchart <laurentp@cse-semaphore.com>
+ *
+ * Copyright (C) 2008, Paulius Zaleckas <paulius.zaleckas@teltonika.lt>
+ *
+ * Based on earlier work by
+ *
+ * Copyright (c) 2003 Intracom S.A.
+ *  by Pantelis Antoniou <panto@intracom.gr>
+ *
+ * 2005 (c) MontaVista Software, Inc.
+ * Vitaly Bordug <vbordug@ru.mvista.com>
+ *
+ * This file is licensed under the terms of the GNU General Public License
+ * version 2. This program is licensed "as is" without any warranty of any
+ * kind, whether express or implied.
+ */
+
+#include <linux/module.h>
+#include <linux/slab.h>
+#include <linux/init.h>
+#include <linux/interrupt.h>
+#include <linux/platform_device.h>
+#include <linux/gpio.h>
+#include <linux/mdio-gpio.h>
+
+#ifdef CONFIG_OF_GPIO
+#include <linux/of_gpio.h>
+#include <linux/of_platform.h>
+#endif
+
+struct mdio_gpio_info {
+	struct mdiobb_ctrl ctrl;
+	int mdc, mdio;
+};
+
+static void mdio_dir(struct mdiobb_ctrl *ctrl, int dir)
+{
+	struct mdio_gpio_info *bitbang =
+		container_of(ctrl, struct mdio_gpio_info, ctrl);
+
+	if (dir)
+		gpio_direction_output(bitbang->mdio, 1);
+	else
+		gpio_direction_input(bitbang->mdio);
+}
+
+static int mdio_get(struct mdiobb_ctrl *ctrl)
+{
+	struct mdio_gpio_info *bitbang =
+		container_of(ctrl, struct mdio_gpio_info, ctrl);
+
+	return gpio_get_value(bitbang->mdio);
+}
+
+static void mdio_set(struct mdiobb_ctrl *ctrl, int what)
+{
+	struct mdio_gpio_info *bitbang =
+		container_of(ctrl, struct mdio_gpio_info, ctrl);
+
+	gpio_set_value(bitbang->mdio, what);
+}
+
+static void mdc_set(struct mdiobb_ctrl *ctrl, int what)
+{
+	struct mdio_gpio_info *bitbang =
+		container_of(ctrl, struct mdio_gpio_info, ctrl);
+
+	gpio_set_value(bitbang->mdc, what);
+}
+
+static struct mdiobb_ops mdio_gpio_ops = {
+	.owner = THIS_MODULE,
+	.set_mdc = mdc_set,
+	.set_mdio_dir = mdio_dir,
+	.set_mdio_data = mdio_set,
+	.get_mdio_data = mdio_get,
+};
+
+static int __devinit mdio_gpio_bus_init(struct device *dev,
+					struct mdio_gpio_platform_data *pdata,
+					int bus_id)
+{
+	struct mii_bus *new_bus;
+	struct mdio_gpio_info *bitbang;
+	int ret = -ENOMEM;
+	int i;
+
+	bitbang = kzalloc(sizeof(*bitbang), GFP_KERNEL);
+	if (!bitbang)
+		goto out;
+
+	bitbang->ctrl.ops = &mdio_gpio_ops;
+	bitbang->mdc = pdata->mdc;
+	bitbang->mdio = pdata->mdio;
+
+	new_bus = alloc_mdio_bitbang(&bitbang->ctrl);
+	if (!new_bus)
+		goto out_free_bitbang;
+
+	new_bus->name = "GPIO Bitbanged MDIO",
+
+	ret = -ENODEV;
+
+	new_bus->phy_mask = pdata->phy_mask;
+	new_bus->irq = pdata->irqs;
+	new_bus->parent = dev;
+
+	if (new_bus->phy_mask == ~0)
+		goto out_free_bus;
+
+	for (i = 0; i < PHY_MAX_ADDR; i++)
+		if (!new_bus->irq[i])
+			new_bus->irq[i] = PHY_POLL;
+
+	snprintf(new_bus->id, MII_BUS_ID_SIZE, "%x", bus_id);
+
+	if (gpio_request(bitbang->mdc, "mdc"))
+		goto out_free_bus;
+
+	if (gpio_request(bitbang->mdio, "mdio"))
+		goto out_free_mdc;
+
+	dev_set_drvdata(dev, new_bus);
+
+	ret = mdiobus_register(new_bus);
+	if (ret)
+		goto out_free_all;
+
+	return 0;
+
+out_free_all:
+	dev_set_drvdata(dev, NULL);
+	gpio_free(bitbang->mdio);
+out_free_mdc:
+	gpio_free(bitbang->mdc);
+out_free_bus:
+	free_mdio_bitbang(new_bus);
+out_free_bitbang:
+	kfree(bitbang);
+out:
+	return ret;
+}
+
+static void __devexit mdio_gpio_bus_destroy(struct device *dev)
+{
+	struct mii_bus *bus = dev_get_drvdata(dev);
+	struct mdio_gpio_info *bitbang = bus->priv;
+
+	mdiobus_unregister(bus);
+	free_mdio_bitbang(bus);
+	dev_set_drvdata(dev, NULL);
+	gpio_free(bitbang->mdc);
+	gpio_free(bitbang->mdio);
+	kfree(bitbang);
+}
+
+static int __devinit mdio_gpio_probe(struct platform_device *pdev)
+{
+	struct mdio_gpio_platform_data *pdata = pdev->dev.platform_data;
+
+	if (!pdata)
+		return -ENODEV;
+
+	return mdio_gpio_bus_init(&pdev->dev, pdata, pdev->id);
+}
+
+static int __devexit mdio_gpio_remove(struct platform_device *pdev)
+{
+	mdio_gpio_bus_destroy(&pdev->dev);
+
+	return 0;
+}
+
+#ifdef CONFIG_OF_GPIO
+static void __devinit add_phy(struct mdio_gpio_platform_data *pdata,
+			      struct device_node *np)
+{
+	const u32 *data;
+	int len, id, irq;
+
+	data = of_get_property(np, "reg", &len);
+	if (!data || len != 4)
+		return;
+
+	id = *data;
+	pdata->phy_mask &= ~(1 << id);
+
+	irq = of_irq_to_resource(np, 0, NULL);
+	if (irq)
+		pdata->irqs[id] = irq;
+}
+
+static int __devinit mdio_ofgpio_probe(struct of_device *ofdev,
+                                        const struct of_device_id *match)
+{
+	struct device_node *np = NULL;
+	struct mdio_gpio_platform_data *pdata;
+
+	pdata = kzalloc(sizeof(*pdata), GFP_KERNEL);
+	if (!pdata)
+		return -ENOMEM;
+
+	pdata->mdc = of_get_gpio(ofdev->node, 0);
+	pdata->mdio = of_get_gpio(ofdev->node, 1);
+
+	if (pdata->mdc < 0 || pdata->mdio < 0)
+		goto out_free;
+
+	while ((np = of_get_next_child(ofdev->node, np)))
+		if (!strcmp(np->type, "ethernet-phy"))
+			add_phy(pdata, np);
+
+	return mdio_gpio_bus_init(&ofdev->dev, pdata, pdata->mdc);
+
+out_free:
+	kfree(pdata);
+	return -ENODEV;
+}
+
+static int __devexit mdio_ofgpio_remove(struct of_device *ofdev)
+{
+	mdio_gpio_bus_destroy(&ofdev->dev);
+	kfree(ofdev->dev.platform_data);
+
+	return 0;
+}
+
+static struct of_device_id mdio_ofgpio_match[] = {
+	{
+		.compatible = "virtual,mdio-gpio",
+	},
+	{},
+};
+
+static struct of_platform_driver mdio_ofgpio_driver = {
+	.name = "mdio-gpio",
+	.match_table = mdio_ofgpio_match,
+	.probe = mdio_ofgpio_probe,
+	.remove = __devexit_p(mdio_ofgpio_remove),
+};
+
+static inline int __init mdio_ofgpio_init(void)
+{
+	return of_register_platform_driver(&mdio_ofgpio_driver);
+}
+
+static inline void __exit mdio_ofgpio_exit(void)
+{
+	of_unregister_platform_driver(&mdio_ofgpio_driver);
+}
+#else
+static inline int __init mdio_ofgpio_init(void) { return 0; }
+static inline void __exit mdio_ofgpio_exit(void) { }
+#endif /* CONFIG_OF_GPIO */
+
+static struct platform_driver mdio_gpio_driver = {
+	.probe = mdio_gpio_probe,
+	.remove = __devexit_p(mdio_gpio_remove),
+	.driver		= {
+		.name	= "mdio-gpio",
+		.owner	= THIS_MODULE,
+	},
+};
+
+static int __init mdio_gpio_init(void)
+{
+	int ret;
+
+	ret = mdio_ofgpio_init();
+	if (ret)
+		return ret;
+
+	ret = platform_driver_register(&mdio_gpio_driver);
+	if (ret)
+		mdio_ofgpio_exit();
+
+	return ret;
+}
+module_init(mdio_gpio_init);
+
+static void __exit mdio_gpio_exit(void)
+{
+	platform_driver_unregister(&mdio_gpio_driver);
+	mdio_ofgpio_exit();
+}
+module_exit(mdio_gpio_exit);
+
+MODULE_ALIAS("platform:mdio-gpio");
+MODULE_AUTHOR("Laurent Pinchart, Paulius Zaleckas");
+MODULE_LICENSE("GPL");
+MODULE_DESCRIPTION("Generic driver for MDIO bus emulation using GPIO");
diff --git a/drivers/net/phy/mdio-ofgpio.c b/drivers/net/phy/mdio-ofgpio.c
deleted file mode 100644
index 2ff97754e574..000000000000
--- a/drivers/net/phy/mdio-ofgpio.c
+++ /dev/null
@@ -1,204 +0,0 @@
-/*
- * OpenFirmware GPIO based MDIO bitbang driver.
- *
- * Copyright (c) 2008 CSE Semaphore Belgium.
- *  by Laurent Pinchart <laurentp@cse-semaphore.com>
- *
- * Based on earlier work by
- *
- * Copyright (c) 2003 Intracom S.A.
- *  by Pantelis Antoniou <panto@intracom.gr>
- *
- * 2005 (c) MontaVista Software, Inc.
- * Vitaly Bordug <vbordug@ru.mvista.com>
- *
- * This file is licensed under the terms of the GNU General Public License
- * version 2. This program is licensed "as is" without any warranty of any
- * kind, whether express or implied.
- */
-
-#include <linux/module.h>
-#include <linux/slab.h>
-#include <linux/init.h>
-#include <linux/interrupt.h>
-#include <linux/mdio-bitbang.h>
-#include <linux/of_gpio.h>
-#include <linux/of_platform.h>
-
-struct mdio_gpio_info {
-	struct mdiobb_ctrl ctrl;
-	int mdc, mdio;
-};
-
-static void mdio_dir(struct mdiobb_ctrl *ctrl, int dir)
-{
-	struct mdio_gpio_info *bitbang =
-		container_of(ctrl, struct mdio_gpio_info, ctrl);
-
-	if (dir)
-		gpio_direction_output(bitbang->mdio, 1);
-	else
-		gpio_direction_input(bitbang->mdio);
-}
-
-static int mdio_read(struct mdiobb_ctrl *ctrl)
-{
-	struct mdio_gpio_info *bitbang =
-		container_of(ctrl, struct mdio_gpio_info, ctrl);
-
-	return gpio_get_value(bitbang->mdio);
-}
-
-static void mdio(struct mdiobb_ctrl *ctrl, int what)
-{
-	struct mdio_gpio_info *bitbang =
-		container_of(ctrl, struct mdio_gpio_info, ctrl);
-
-	gpio_set_value(bitbang->mdio, what);
-}
-
-static void mdc(struct mdiobb_ctrl *ctrl, int what)
-{
-	struct mdio_gpio_info *bitbang =
-		container_of(ctrl, struct mdio_gpio_info, ctrl);
-
-	gpio_set_value(bitbang->mdc, what);
-}
-
-static struct mdiobb_ops mdio_gpio_ops = {
-	.owner = THIS_MODULE,
-	.set_mdc = mdc,
-	.set_mdio_dir = mdio_dir,
-	.set_mdio_data = mdio,
-	.get_mdio_data = mdio_read,
-};
-
-static int __devinit mdio_ofgpio_bitbang_init(struct mii_bus *bus,
-                                         struct device_node *np)
-{
-	struct mdio_gpio_info *bitbang = bus->priv;
-
-	bitbang->mdc = of_get_gpio(np, 0);
-	bitbang->mdio = of_get_gpio(np, 1);
-
-	if (bitbang->mdc < 0 || bitbang->mdio < 0)
-		return -ENODEV;
-
-	snprintf(bus->id, MII_BUS_ID_SIZE, "%x", bitbang->mdc);
-	return 0;
-}
-
-static void __devinit add_phy(struct mii_bus *bus, struct device_node *np)
-{
-	const u32 *data;
-	int len, id, irq;
-
-	data = of_get_property(np, "reg", &len);
-	if (!data || len != 4)
-		return;
-
-	id = *data;
-	bus->phy_mask &= ~(1 << id);
-
-	irq = of_irq_to_resource(np, 0, NULL);
-	if (irq != NO_IRQ)
-		bus->irq[id] = irq;
-}
-
-static int __devinit mdio_ofgpio_probe(struct of_device *ofdev,
-                                        const struct of_device_id *match)
-{
-	struct device_node *np = NULL;
-	struct mii_bus *new_bus;
-	struct mdio_gpio_info *bitbang;
-	int ret = -ENOMEM;
-	int i;
-
-	bitbang = kzalloc(sizeof(struct mdio_gpio_info), GFP_KERNEL);
-	if (!bitbang)
-		goto out;
-
-	bitbang->ctrl.ops = &mdio_gpio_ops;
-
-	new_bus = alloc_mdio_bitbang(&bitbang->ctrl);
-	if (!new_bus)
-		goto out_free_bitbang;
-
-	new_bus->name = "GPIO Bitbanged MII",
-
-	ret = mdio_ofgpio_bitbang_init(new_bus, ofdev->node);
-	if (ret)
-		goto out_free_bus;
-
-	new_bus->phy_mask = ~0;
-	new_bus->irq = kmalloc(sizeof(int) * PHY_MAX_ADDR, GFP_KERNEL);
-	if (!new_bus->irq)
-		goto out_free_bus;
-
-	for (i = 0; i < PHY_MAX_ADDR; i++)
-		new_bus->irq[i] = -1;
-
-	while ((np = of_get_next_child(ofdev->node, np)))
-		if (!strcmp(np->type, "ethernet-phy"))
-			add_phy(new_bus, np);
-
-	new_bus->parent = &ofdev->dev;
-	dev_set_drvdata(&ofdev->dev, new_bus);
-
-	ret = mdiobus_register(new_bus);
-	if (ret)
-		goto out_free_irqs;
-
-	return 0;
-
-out_free_irqs:
-	dev_set_drvdata(&ofdev->dev, NULL);
-	kfree(new_bus->irq);
-out_free_bus:
-	free_mdio_bitbang(new_bus);
-out_free_bitbang:
-	kfree(bitbang);
-out:
-	return ret;
-}
-
-static int mdio_ofgpio_remove(struct of_device *ofdev)
-{
-	struct mii_bus *bus = dev_get_drvdata(&ofdev->dev);
-	struct mdio_gpio_info *bitbang = bus->priv;
-
-	mdiobus_unregister(bus);
-	kfree(bus->irq);
-	free_mdio_bitbang(bus);
-	dev_set_drvdata(&ofdev->dev, NULL);
-	kfree(bitbang);
-
-	return 0;
-}
-
-static struct of_device_id mdio_ofgpio_match[] = {
-	{
-		.compatible = "virtual,mdio-gpio",
-	},
-	{},
-};
-
-static struct of_platform_driver mdio_ofgpio_driver = {
-	.name = "mdio-gpio",
-	.match_table = mdio_ofgpio_match,
-	.probe = mdio_ofgpio_probe,
-	.remove = mdio_ofgpio_remove,
-};
-
-static int mdio_ofgpio_init(void)
-{
-	return of_register_platform_driver(&mdio_ofgpio_driver);
-}
-
-static void mdio_ofgpio_exit(void)
-{
-	of_unregister_platform_driver(&mdio_ofgpio_driver);
-}
-
-module_init(mdio_ofgpio_init);
-module_exit(mdio_ofgpio_exit);
diff --git a/drivers/net/phy/mdio_bus.c b/drivers/net/phy/mdio_bus.c
index 289fc267edf3..11adf6ed4628 100644
--- a/drivers/net/phy/mdio_bus.c
+++ b/drivers/net/phy/mdio_bus.c
@@ -63,7 +63,9 @@ EXPORT_SYMBOL(mdiobus_alloc);
 static void mdiobus_release(struct device *d)
 {
 	struct mii_bus *bus = to_mii_bus(d);
-	BUG_ON(bus->state != MDIOBUS_RELEASED);
+	BUG_ON(bus->state != MDIOBUS_RELEASED &&
+	       /* for compatibility with error handling in drivers */
+	       bus->state != MDIOBUS_ALLOCATED);
 	kfree(bus);
 }
 
@@ -83,8 +85,7 @@ static struct class mdio_bus_class = {
  */
 int mdiobus_register(struct mii_bus *bus)
 {
-	int i;
-	int err = 0;
+	int i, err;
 
 	if (NULL == bus || NULL == bus->name ||
 			NULL == bus->read ||
@@ -97,7 +98,7 @@ int mdiobus_register(struct mii_bus *bus)
 	bus->dev.parent = bus->parent;
 	bus->dev.class = &mdio_bus_class;
 	bus->dev.groups = NULL;
-	memcpy(bus->dev.bus_id, bus->id, MII_BUS_ID_SIZE);
+	dev_set_name(&bus->dev, bus->id);
 
 	err = device_register(&bus->dev);
 	if (err) {
@@ -116,16 +117,23 @@ int mdiobus_register(struct mii_bus *bus)
 			struct phy_device *phydev;
 
 			phydev = mdiobus_scan(bus, i);
-			if (IS_ERR(phydev))
+			if (IS_ERR(phydev)) {
 				err = PTR_ERR(phydev);
+				goto error;
+			}
 		}
 	}
 
-	if (!err)
-		bus->state = MDIOBUS_REGISTERED;
-
+	bus->state = MDIOBUS_REGISTERED;
 	pr_info("%s: probed\n", bus->name);
+	return 0;
 
+error:
+	while (--i >= 0) {
+		if (bus->phy_map[i])
+			device_unregister(&bus->phy_map[i]->dev);
+	}
+	device_del(&bus->dev);
 	return err;
 }
 EXPORT_SYMBOL(mdiobus_register);
@@ -192,7 +200,7 @@ struct phy_device *mdiobus_scan(struct mii_bus *bus, int addr)
 
 	phydev->dev.parent = bus->parent;
 	phydev->dev.bus = &mdio_bus_type;
-	snprintf(phydev->dev.bus_id, BUS_ID_SIZE, PHY_ID_FMT, bus->id, addr);
+	dev_set_name(&phydev->dev, PHY_ID_FMT, bus->id, addr);
 
 	phydev->bus = bus;
 
@@ -285,9 +293,12 @@ static int mdio_bus_suspend(struct device * dev, pm_message_t state)
 {
 	int ret = 0;
 	struct device_driver *drv = dev->driver;
+	struct phy_driver *phydrv = to_phy_driver(drv);
+	struct phy_device *phydev = to_phy_device(dev);
 
-	if (drv && drv->suspend)
-		ret = drv->suspend(dev, state);
+	if ((!device_may_wakeup(phydev->dev.parent)) &&
+		(phydrv && phydrv->suspend))
+			ret = phydrv->suspend(phydev);
 
 	return ret;
 }
@@ -296,9 +307,12 @@ static int mdio_bus_resume(struct device * dev)
 {
 	int ret = 0;
 	struct device_driver *drv = dev->driver;
+	struct phy_driver *phydrv = to_phy_driver(drv);
+	struct phy_device *phydev = to_phy_device(dev);
 
-	if (drv && drv->resume)
-		ret = drv->resume(dev);
+	if ((!device_may_wakeup(phydev->dev.parent)) &&
+		(phydrv && phydrv->resume))
+		ret = phydrv->resume(phydev);
 
 	return ret;
 }
diff --git a/drivers/net/phy/national.c b/drivers/net/phy/national.c
new file mode 100644
index 000000000000..6c636eb72089
--- /dev/null
+++ b/drivers/net/phy/national.c
@@ -0,0 +1,155 @@
+/*
+ * drivers/net/phy/national.c
+ *
+ * Driver for National Semiconductor PHYs
+ *
+ * Author: Stuart Menefy <stuart.menefy@st.com>
+ * Maintainer: Giuseppe Cavallaro <peppe.cavallaro@st.com>
+ *
+ * Copyright (c) 2008 STMicroelectronics Limited
+ *
+ * This program is free software; you can redistribute  it and/or modify it
+ * under  the terms of  the GNU General  Public License as published by the
+ * Free Software Foundation;  either version 2 of the  License, or (at your
+ * option) any later version.
+ *
+ */
+
+#include <linux/kernel.h>
+#include <linux/module.h>
+#include <linux/mii.h>
+#include <linux/ethtool.h>
+#include <linux/phy.h>
+#include <linux/netdevice.h>
+
+/* DP83865 phy identifier values */
+#define DP83865_PHY_ID	0x20005c7a
+
+#define DP83865_INT_MASK_REG 0x15
+#define DP83865_INT_MASK_STATUS 0x14
+
+#define DP83865_INT_REMOTE_FAULT 0x0008
+#define DP83865_INT_ANE_COMPLETED 0x0010
+#define DP83865_INT_LINK_CHANGE	0xe000
+#define DP83865_INT_MASK_DEFAULT (DP83865_INT_REMOTE_FAULT | \
+				DP83865_INT_ANE_COMPLETED | \
+				DP83865_INT_LINK_CHANGE)
+
+/* Advanced proprietary configuration */
+#define NS_EXP_MEM_CTL	0x16
+#define NS_EXP_MEM_DATA	0x1d
+#define NS_EXP_MEM_ADD	0x1e
+
+#define LED_CTRL_REG 0x13
+#define AN_FALLBACK_AN 0x0001
+#define AN_FALLBACK_CRC 0x0002
+#define AN_FALLBACK_IE 0x0004
+#define ALL_FALLBACK_ON (AN_FALLBACK_AN |  AN_FALLBACK_CRC | AN_FALLBACK_IE)
+
+enum hdx_loopback {
+	hdx_loopback_on = 0,
+	hdx_loopback_off = 1,
+};
+
+static u8 ns_exp_read(struct phy_device *phydev, u16 reg)
+{
+	phy_write(phydev, NS_EXP_MEM_ADD, reg);
+	return phy_read(phydev, NS_EXP_MEM_DATA);
+}
+
+static void ns_exp_write(struct phy_device *phydev, u16 reg, u8 data)
+{
+	phy_write(phydev, NS_EXP_MEM_ADD, reg);
+	phy_write(phydev, NS_EXP_MEM_DATA, data);
+}
+
+static int ns_config_intr(struct phy_device *phydev)
+{
+	int err;
+
+	if (phydev->interrupts == PHY_INTERRUPT_ENABLED)
+		err = phy_write(phydev, DP83865_INT_MASK_REG,
+				DP83865_INT_MASK_DEFAULT);
+	else
+		err = phy_write(phydev, DP83865_INT_MASK_REG, 0);
+
+	return err;
+}
+
+static int ns_ack_interrupt(struct phy_device *phydev)
+{
+	int ret = phy_read(phydev, DP83865_INT_MASK_STATUS);
+	if (ret < 0)
+		return ret;
+
+	return 0;
+}
+
+static void ns_giga_speed_fallback(struct phy_device *phydev, int mode)
+{
+	int bmcr = phy_read(phydev, MII_BMCR);
+
+	phy_write(phydev, MII_BMCR, (bmcr | BMCR_PDOWN));
+
+	/* Enable 8 bit expended memory read/write (no auto increment) */
+	phy_write(phydev, NS_EXP_MEM_CTL, 0);
+	phy_write(phydev, NS_EXP_MEM_ADD, 0x1C0);
+	phy_write(phydev, NS_EXP_MEM_DATA, 0x0008);
+	phy_write(phydev, MII_BMCR, (bmcr & ~BMCR_PDOWN));
+	phy_write(phydev, LED_CTRL_REG, mode);
+	return;
+}
+
+static void ns_10_base_t_hdx_loopack(struct phy_device *phydev, int disable)
+{
+	if (disable)
+		ns_exp_write(phydev, 0x1c0, ns_exp_read(phydev, 0x1c0) | 1);
+	else
+		ns_exp_write(phydev, 0x1c0,
+			     ns_exp_read(phydev, 0x1c0) & 0xfffe);
+
+	printk(KERN_DEBUG "DP83865 PHY: 10BASE-T HDX loopback %s\n",
+	       (ns_exp_read(phydev, 0x1c0) & 0x0001) ? "off" : "on");
+
+	return;
+}
+
+static int ns_config_init(struct phy_device *phydev)
+{
+	ns_giga_speed_fallback(phydev, ALL_FALLBACK_ON);
+	/* In the latest MAC or switches design, the 10 Mbps loopback
+	   is desired to be turned off. */
+	ns_10_base_t_hdx_loopack(phydev, hdx_loopback_off);
+	return ns_ack_interrupt(phydev);
+}
+
+static struct phy_driver dp83865_driver = {
+	.phy_id = DP83865_PHY_ID,
+	.phy_id_mask = 0xfffffff0,
+	.name = "NatSemi DP83865",
+	.features = PHY_GBIT_FEATURES | SUPPORTED_Pause | SUPPORTED_Asym_Pause,
+	.flags = PHY_HAS_INTERRUPT,
+	.config_init = ns_config_init,
+	.config_aneg = genphy_config_aneg,
+	.read_status = genphy_read_status,
+	.ack_interrupt = ns_ack_interrupt,
+	.config_intr = ns_config_intr,
+	.driver = {.owner = THIS_MODULE,}
+};
+
+static int __init ns_init(void)
+{
+	return phy_driver_register(&dp83865_driver);
+}
+
+static void __exit ns_exit(void)
+{
+	phy_driver_unregister(&dp83865_driver);
+}
+
+MODULE_DESCRIPTION("NatSemi PHY driver");
+MODULE_AUTHOR("Stuart Menefy");
+MODULE_LICENSE("GPL");
+
+module_init(ns_init);
+module_exit(ns_exit);
diff --git a/drivers/net/phy/phy.c b/drivers/net/phy/phy.c
index df4e6257d4a7..e4ede6080c9d 100644
--- a/drivers/net/phy/phy.c
+++ b/drivers/net/phy/phy.c
@@ -45,7 +45,7 @@
  */
 void phy_print_status(struct phy_device *phydev)
 {
-	pr_info("PHY: %s - Link is %s", phydev->dev.bus_id,
+	pr_info("PHY: %s - Link is %s", dev_name(&phydev->dev),
 			phydev->link ? "Up" : "Down");
 	if (phydev->link)
 		printk(" - %d/%s", phydev->speed,
diff --git a/drivers/net/phy/phy_device.c b/drivers/net/phy/phy_device.c
index 25acbbde4a60..e35460165bf7 100644
--- a/drivers/net/phy/phy_device.c
+++ b/drivers/net/phy/phy_device.c
@@ -74,7 +74,7 @@ int phy_register_fixup(const char *bus_id, u32 phy_uid, u32 phy_uid_mask,
 	if (!fixup)
 		return -ENOMEM;
 
-	strncpy(fixup->bus_id, bus_id, BUS_ID_SIZE);
+	strlcpy(fixup->bus_id, bus_id, sizeof(fixup->bus_id));
 	fixup->phy_uid = phy_uid;
 	fixup->phy_uid_mask = phy_uid_mask;
 	fixup->run = run;
@@ -109,7 +109,7 @@ EXPORT_SYMBOL(phy_register_fixup_for_id);
  */
 static int phy_needs_fixup(struct phy_device *phydev, struct phy_fixup *fixup)
 {
-	if (strcmp(fixup->bus_id, phydev->dev.bus_id) != 0)
+	if (strcmp(fixup->bus_id, dev_name(&phydev->dev)) != 0)
 		if (strcmp(fixup->bus_id, PHY_ANY_ID) != 0)
 			return 0;
 
@@ -232,7 +232,7 @@ struct phy_device * get_phy_device(struct mii_bus *bus, int addr)
 		return NULL;
 
 	/*
-	 * Broken hardware is sometimes missing the pull down resistor on the
+	 * Broken hardware is sometimes missing the pull-up resistor on the
 	 * MDIO line, which results in reads to non-existent devices returning
 	 * 0 rather than 0xffff. Catch this here and treat 0 as a non-existent
 	 * device as well.
@@ -517,23 +517,6 @@ int genphy_setup_forced(struct phy_device *phydev)
 	
 	err = phy_write(phydev, MII_BMCR, ctl);
 
-	if (err < 0)
-		return err;
-
-	/*
-	 * Run the fixups on this PHY, just in case the
-	 * board code needs to change something after a reset
-	 */
-	err = phy_scan_fixups(phydev);
-
-	if (err < 0)
-		return err;
-
-	/* We just reset the device, so we'd better configure any
-	 * settings the PHY requires to operate */
-	if (phydev->drv->config_init)
-		err = phydev->drv->config_init(phydev);
-
 	return err;
 }
 
@@ -779,7 +762,35 @@ static int genphy_config_init(struct phy_device *phydev)
 
 	return 0;
 }
+int genphy_suspend(struct phy_device *phydev)
+{
+	int value;
 
+	mutex_lock(&phydev->lock);
+
+	value = phy_read(phydev, MII_BMCR);
+	phy_write(phydev, MII_BMCR, (value | BMCR_PDOWN));
+
+	mutex_unlock(&phydev->lock);
+
+	return 0;
+}
+EXPORT_SYMBOL(genphy_suspend);
+
+int genphy_resume(struct phy_device *phydev)
+{
+	int value;
+
+	mutex_lock(&phydev->lock);
+
+	value = phy_read(phydev, MII_BMCR);
+	phy_write(phydev, MII_BMCR, (value & ~BMCR_PDOWN));
+
+	mutex_unlock(&phydev->lock);
+
+	return 0;
+}
+EXPORT_SYMBOL(genphy_resume);
 
 /**
  * phy_probe - probe and init a PHY device
@@ -855,7 +866,6 @@ int phy_driver_register(struct phy_driver *new_driver)
 {
 	int retval;
 
-	memset(&new_driver->driver, 0, sizeof(new_driver->driver));
 	new_driver->driver.name = new_driver->name;
 	new_driver->driver.bus = &mdio_bus_type;
 	new_driver->driver.probe = phy_probe;
@@ -890,6 +900,8 @@ static struct phy_driver genphy_driver = {
 	.features	= 0,
 	.config_aneg	= genphy_config_aneg,
 	.read_status	= genphy_read_status,
+	.suspend	= genphy_suspend,
+	.resume		= genphy_resume,
 	.driver		= {.owner= THIS_MODULE, },
 };
 
diff --git a/drivers/net/phy/smsc.c b/drivers/net/phy/smsc.c
index 73baa7a3bb0e..c05d38d46350 100644
--- a/drivers/net/phy/smsc.c
+++ b/drivers/net/phy/smsc.c
@@ -126,6 +126,27 @@ static struct phy_driver lan8700_driver = {
 	.driver		= { .owner = THIS_MODULE, }
 };
 
+static struct phy_driver lan911x_int_driver = {
+	.phy_id		= 0x0007c0d0, /* OUI=0x00800f, Model#=0x0d */
+	.phy_id_mask	= 0xfffffff0,
+	.name		= "SMSC LAN911x Internal PHY",
+
+	.features	= (PHY_BASIC_FEATURES | SUPPORTED_Pause
+				| SUPPORTED_Asym_Pause),
+	.flags		= PHY_HAS_INTERRUPT | PHY_HAS_MAGICANEG,
+
+	/* basic functions */
+	.config_aneg	= genphy_config_aneg,
+	.read_status	= genphy_read_status,
+	.config_init	= smsc_phy_config_init,
+
+	/* IRQ related */
+	.ack_interrupt	= smsc_phy_ack_interrupt,
+	.config_intr	= smsc_phy_config_intr,
+
+	.driver		= { .owner = THIS_MODULE, }
+};
+
 static int __init smsc_init(void)
 {
 	int ret;
@@ -142,8 +163,14 @@ static int __init smsc_init(void)
 	if (ret)
 		goto err3;
 
+	ret = phy_driver_register (&lan911x_int_driver);
+	if (ret)
+		goto err4;
+
 	return 0;
 
+err4:
+	phy_driver_unregister (&lan8700_driver);
 err3:
 	phy_driver_unregister (&lan8187_driver);
 err2:
@@ -154,6 +181,7 @@ err1:
 
 static void __exit smsc_exit(void)
 {
+	phy_driver_unregister (&lan911x_int_driver);
 	phy_driver_unregister (&lan8700_driver);
 	phy_driver_unregister (&lan8187_driver);
 	phy_driver_unregister (&lan83c185_driver);
diff --git a/drivers/net/phy/ste10Xp.c b/drivers/net/phy/ste10Xp.c
new file mode 100644
index 000000000000..6bdb0d53aaf9
--- /dev/null
+++ b/drivers/net/phy/ste10Xp.c
@@ -0,0 +1,137 @@
+/*
+ * drivers/net/phy/ste10Xp.c
+ *
+ * Driver for STMicroelectronics STe10Xp PHYs
+ *
+ * Author: Giuseppe Cavallaro <peppe.cavallaro@st.com>
+ *
+ * Copyright (c) 2008 STMicroelectronics Limited
+ *
+ * This program is free software; you can redistribute  it and/or modify it
+ * under  the terms of  the GNU General  Public License as published by the
+ * Free Software Foundation;  either version 2 of the  License, or (at your
+ * option) any later version.
+ *
+ */
+
+#include <linux/module.h>
+#include <linux/init.h>
+#include <linux/sched.h>
+#include <linux/kernel.h>
+#include <linux/moduleparam.h>
+#include <linux/interrupt.h>
+#include <linux/netdevice.h>
+#include <linux/ethtool.h>
+#include <linux/mii.h>
+#include <linux/phy.h>
+
+#define MII_XCIIS   	0x11	/* Configuration Info IRQ & Status Reg */
+#define MII_XIE     	0x12	/* Interrupt Enable Register */
+#define MII_XIE_DEFAULT_MASK 0x0070 /* ANE complete, Remote Fault, Link Down */
+
+#define STE101P_PHY_ID		0x00061c50
+#define STE100P_PHY_ID       	0x1c040011
+
+static int ste10Xp_config_init(struct phy_device *phydev)
+{
+	int value, err;
+
+	/* Software Reset PHY */
+	value = phy_read(phydev, MII_BMCR);
+	if (value < 0)
+		return value;
+
+	value |= BMCR_RESET;
+	err = phy_write(phydev, MII_BMCR, value);
+	if (err < 0)
+		return err;
+
+	do {
+		value = phy_read(phydev, MII_BMCR);
+	} while (value & BMCR_RESET);
+
+	return 0;
+}
+
+static int ste10Xp_config_intr(struct phy_device *phydev)
+{
+	int err, value;
+
+	if (phydev->interrupts == PHY_INTERRUPT_ENABLED) {
+		/* Enable all STe101P interrupts (PR12) */
+		err = phy_write(phydev, MII_XIE, MII_XIE_DEFAULT_MASK);
+		/* clear any pending interrupts */
+		if (err == 0) {
+			value = phy_read(phydev, MII_XCIIS);
+			if (value < 0)
+				err = value;
+		}
+	} else
+		err = phy_write(phydev, MII_XIE, 0);
+
+	return err;
+}
+
+static int ste10Xp_ack_interrupt(struct phy_device *phydev)
+{
+	int err = phy_read(phydev, MII_XCIIS);
+	if (err < 0)
+		return err;
+
+	return 0;
+}
+
+static struct phy_driver ste101p_pdriver = {
+	.phy_id = STE101P_PHY_ID,
+	.phy_id_mask = 0xfffffff0,
+	.name = "STe101p",
+	.features = PHY_BASIC_FEATURES | SUPPORTED_Pause,
+	.flags = PHY_HAS_INTERRUPT,
+	.config_init = ste10Xp_config_init,
+	.config_aneg = genphy_config_aneg,
+	.read_status = genphy_read_status,
+	.ack_interrupt = ste10Xp_ack_interrupt,
+	.config_intr = ste10Xp_config_intr,
+	.suspend = genphy_suspend,
+	.resume = genphy_resume,
+	.driver = {.owner = THIS_MODULE,}
+};
+
+static struct phy_driver ste100p_pdriver = {
+	.phy_id = STE100P_PHY_ID,
+	.phy_id_mask = 0xffffffff,
+	.name = "STe100p",
+	.features = PHY_BASIC_FEATURES | SUPPORTED_Pause,
+	.flags = PHY_HAS_INTERRUPT,
+	.config_init = ste10Xp_config_init,
+	.config_aneg = genphy_config_aneg,
+	.read_status = genphy_read_status,
+	.ack_interrupt = ste10Xp_ack_interrupt,
+	.config_intr = ste10Xp_config_intr,
+	.suspend = genphy_suspend,
+	.resume = genphy_resume,
+	.driver = {.owner = THIS_MODULE,}
+};
+
+static int __init ste10Xp_init(void)
+{
+	int retval;
+
+	retval = phy_driver_register(&ste100p_pdriver);
+	if (retval < 0)
+		return retval;
+	return phy_driver_register(&ste101p_pdriver);
+}
+
+static void __exit ste10Xp_exit(void)
+{
+	phy_driver_unregister(&ste100p_pdriver);
+	phy_driver_unregister(&ste101p_pdriver);
+}
+
+module_init(ste10Xp_init);
+module_exit(ste10Xp_exit);
+
+MODULE_DESCRIPTION("STMicroelectronics STe10Xp PHY driver");
+MODULE_AUTHOR("Giuseppe Cavallaro <peppe.cavallaro@st.com>");
+MODULE_LICENSE("GPL");