ixgbe: Reorder link flow control functions in ixgbe_common.c

We can avoid many of the forward declarations found in ixgbe_common.c by
just reordering things so this patch does that to help cleanup the code.

Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Tested-by: Ross Brattain <ross.b.brattain@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>

1 files changed, 282 insertions, 290 deletions

diff --git a/drivers/net/ethernet/intel/ixgbe/ixgbe_common.c b/drivers/net/ethernet/intel/ixgbe/ixgbe_common.c
index 9854d948f135..3035f1938f5b 100644
--- a/drivers/net/ethernet/intel/ixgbe/ixgbe_common.c
+++ b/drivers/net/ethernet/intel/ixgbe/ixgbe_common.c
@@ -47,13 +47,6 @@ static void ixgbe_lower_eeprom_clk(struct ixgbe_hw *hw, u32 *eec);
 static void ixgbe_release_eeprom(struct ixgbe_hw *hw);
 
 static s32 ixgbe_mta_vector(struct ixgbe_hw *hw, u8 *mc_addr);
-static s32 ixgbe_fc_autoneg_fiber(struct ixgbe_hw *hw);
-static s32 ixgbe_fc_autoneg_backplane(struct ixgbe_hw *hw);
-static s32 ixgbe_fc_autoneg_copper(struct ixgbe_hw *hw);
-static s32 ixgbe_device_supports_autoneg_fc(struct ixgbe_hw *hw);
-static s32 ixgbe_negotiate_fc(struct ixgbe_hw *hw, u32 adv_reg, u32 lp_reg,
-			      u32 adv_sym, u32 adv_asm, u32 lp_sym, u32 lp_asm);
-static s32 ixgbe_setup_fc(struct ixgbe_hw *hw, s32 packetbuf_num);
 static s32 ixgbe_poll_eerd_eewr_done(struct ixgbe_hw *hw, u32 ee_reg);
 static s32 ixgbe_read_eeprom_buffer_bit_bang(struct ixgbe_hw *hw, u16 offset,
 					     u16 words, u16 *data);
@@ -64,6 +57,216 @@ static s32 ixgbe_detect_eeprom_page_size_generic(struct ixgbe_hw *hw,
 static s32 ixgbe_disable_pcie_master(struct ixgbe_hw *hw);
 
 /**
+ *  ixgbe_device_supports_autoneg_fc - Check if phy supports autoneg flow
+ *  control
+ *  @hw: pointer to hardware structure
+ *
+ *  There are several phys that do not support autoneg flow control. This
+ *  function check the device id to see if the associated phy supports
+ *  autoneg flow control.
+ **/
+static s32 ixgbe_device_supports_autoneg_fc(struct ixgbe_hw *hw)
+{
+
+	switch (hw->device_id) {
+	case IXGBE_DEV_ID_X540T:
+		return 0;
+	case IXGBE_DEV_ID_82599_T3_LOM:
+		return 0;
+	default:
+		return IXGBE_ERR_FC_NOT_SUPPORTED;
+	}
+}
+
+/**
+ *  ixgbe_setup_fc - Set up flow control
+ *  @hw: pointer to hardware structure
+ *
+ *  Called at init time to set up flow control.
+ **/
+static s32 ixgbe_setup_fc(struct ixgbe_hw *hw, s32 packetbuf_num)
+{
+	s32 ret_val = 0;
+	u32 reg = 0, reg_bp = 0;
+	u16 reg_cu = 0;
+
+#ifdef CONFIG_DCB
+	if (hw->fc.requested_mode == ixgbe_fc_pfc) {
+		hw->fc.current_mode = hw->fc.requested_mode;
+		goto out;
+	}
+
+#endif /* CONFIG_DCB */
+	/* Validate the packetbuf configuration */
+	if (packetbuf_num < 0 || packetbuf_num > 7) {
+		hw_dbg(hw, "Invalid packet buffer number [%d], expected range is 0-7\n",
+		       packetbuf_num);
+		ret_val = IXGBE_ERR_INVALID_LINK_SETTINGS;
+		goto out;
+	}
+
+	/*
+	 * Validate the water mark configuration.  Zero water marks are invalid
+	 * because it causes the controller to just blast out fc packets.
+	 */
+	if (!hw->fc.low_water ||
+	    !hw->fc.high_water[packetbuf_num] ||
+	    !hw->fc.pause_time) {
+		hw_dbg(hw, "Invalid water mark configuration\n");
+		ret_val = IXGBE_ERR_INVALID_LINK_SETTINGS;
+		goto out;
+	}
+
+	/*
+	 * Validate the requested mode.  Strict IEEE mode does not allow
+	 * ixgbe_fc_rx_pause because it will cause us to fail at UNH.
+	 */
+	if (hw->fc.strict_ieee && hw->fc.requested_mode == ixgbe_fc_rx_pause) {
+		hw_dbg(hw, "ixgbe_fc_rx_pause not valid in strict IEEE mode\n");
+		ret_val = IXGBE_ERR_INVALID_LINK_SETTINGS;
+		goto out;
+	}
+
+	/*
+	 * 10gig parts do not have a word in the EEPROM to determine the
+	 * default flow control setting, so we explicitly set it to full.
+	 */
+	if (hw->fc.requested_mode == ixgbe_fc_default)
+		hw->fc.requested_mode = ixgbe_fc_full;
+
+	/*
+	 * Set up the 1G and 10G flow control advertisement registers so the
+	 * HW will be able to do fc autoneg once the cable is plugged in.  If
+	 * we link at 10G, the 1G advertisement is harmless and vice versa.
+	 */
+
+	switch (hw->phy.media_type) {
+	case ixgbe_media_type_fiber:
+	case ixgbe_media_type_backplane:
+		reg = IXGBE_READ_REG(hw, IXGBE_PCS1GANA);
+		reg_bp = IXGBE_READ_REG(hw, IXGBE_AUTOC);
+		break;
+
+	case ixgbe_media_type_copper:
+		hw->phy.ops.read_reg(hw, MDIO_AN_ADVERTISE,
+					MDIO_MMD_AN, &reg_cu);
+		break;
+
+	default:
+		;
+	}
+
+	/*
+	 * The possible values of fc.requested_mode are:
+	 * 0: Flow control is completely disabled
+	 * 1: Rx flow control is enabled (we can receive pause frames,
+	 *    but not send pause frames).
+	 * 2: Tx flow control is enabled (we can send pause frames but
+	 *    we do not support receiving pause frames).
+	 * 3: Both Rx and Tx flow control (symmetric) are enabled.
+#ifdef CONFIG_DCB
+	 * 4: Priority Flow Control is enabled.
+#endif
+	 * other: Invalid.
+	 */
+	switch (hw->fc.requested_mode) {
+	case ixgbe_fc_none:
+		/* Flow control completely disabled by software override. */
+		reg &= ~(IXGBE_PCS1GANA_SYM_PAUSE | IXGBE_PCS1GANA_ASM_PAUSE);
+		if (hw->phy.media_type == ixgbe_media_type_backplane)
+			reg_bp &= ~(IXGBE_AUTOC_SYM_PAUSE |
+				    IXGBE_AUTOC_ASM_PAUSE);
+		else if (hw->phy.media_type == ixgbe_media_type_copper)
+			reg_cu &= ~(IXGBE_TAF_SYM_PAUSE | IXGBE_TAF_ASM_PAUSE);
+		break;
+	case ixgbe_fc_rx_pause:
+		/*
+		 * Rx Flow control is enabled and Tx Flow control is
+		 * disabled by software override. Since there really
+		 * isn't a way to advertise that we are capable of RX
+		 * Pause ONLY, we will advertise that we support both
+		 * symmetric and asymmetric Rx PAUSE.  Later, we will
+		 * disable the adapter's ability to send PAUSE frames.
+		 */
+		reg |= (IXGBE_PCS1GANA_SYM_PAUSE | IXGBE_PCS1GANA_ASM_PAUSE);
+		if (hw->phy.media_type == ixgbe_media_type_backplane)
+			reg_bp |= (IXGBE_AUTOC_SYM_PAUSE |
+				   IXGBE_AUTOC_ASM_PAUSE);
+		else if (hw->phy.media_type == ixgbe_media_type_copper)
+			reg_cu |= (IXGBE_TAF_SYM_PAUSE | IXGBE_TAF_ASM_PAUSE);
+		break;
+	case ixgbe_fc_tx_pause:
+		/*
+		 * Tx Flow control is enabled, and Rx Flow control is
+		 * disabled by software override.
+		 */
+		reg |= (IXGBE_PCS1GANA_ASM_PAUSE);
+		reg &= ~(IXGBE_PCS1GANA_SYM_PAUSE);
+		if (hw->phy.media_type == ixgbe_media_type_backplane) {
+			reg_bp |= (IXGBE_AUTOC_ASM_PAUSE);
+			reg_bp &= ~(IXGBE_AUTOC_SYM_PAUSE);
+		} else if (hw->phy.media_type == ixgbe_media_type_copper) {
+			reg_cu |= (IXGBE_TAF_ASM_PAUSE);
+			reg_cu &= ~(IXGBE_TAF_SYM_PAUSE);
+		}
+		break;
+	case ixgbe_fc_full:
+		/* Flow control (both Rx and Tx) is enabled by SW override. */
+		reg |= (IXGBE_PCS1GANA_SYM_PAUSE | IXGBE_PCS1GANA_ASM_PAUSE);
+		if (hw->phy.media_type == ixgbe_media_type_backplane)
+			reg_bp |= (IXGBE_AUTOC_SYM_PAUSE |
+				   IXGBE_AUTOC_ASM_PAUSE);
+		else if (hw->phy.media_type == ixgbe_media_type_copper)
+			reg_cu |= (IXGBE_TAF_SYM_PAUSE | IXGBE_TAF_ASM_PAUSE);
+		break;
+#ifdef CONFIG_DCB
+	case ixgbe_fc_pfc:
+		goto out;
+		break;
+#endif /* CONFIG_DCB */
+	default:
+		hw_dbg(hw, "Flow control param set incorrectly\n");
+		ret_val = IXGBE_ERR_CONFIG;
+		goto out;
+		break;
+	}
+
+	if (hw->mac.type != ixgbe_mac_X540) {
+		/*
+		 * Enable auto-negotiation between the MAC & PHY;
+		 * the MAC will advertise clause 37 flow control.
+		 */
+		IXGBE_WRITE_REG(hw, IXGBE_PCS1GANA, reg);
+		reg = IXGBE_READ_REG(hw, IXGBE_PCS1GLCTL);
+
+		/* Disable AN timeout */
+		if (hw->fc.strict_ieee)
+			reg &= ~IXGBE_PCS1GLCTL_AN_1G_TIMEOUT_EN;
+
+		IXGBE_WRITE_REG(hw, IXGBE_PCS1GLCTL, reg);
+		hw_dbg(hw, "Set up FC; PCS1GLCTL = 0x%08X\n", reg);
+	}
+
+	/*
+	 * AUTOC restart handles negotiation of 1G and 10G on backplane
+	 * and copper. There is no need to set the PCS1GCTL register.
+	 *
+	 */
+	if (hw->phy.media_type == ixgbe_media_type_backplane) {
+		reg_bp |= IXGBE_AUTOC_AN_RESTART;
+		IXGBE_WRITE_REG(hw, IXGBE_AUTOC, reg_bp);
+	} else if ((hw->phy.media_type == ixgbe_media_type_copper) &&
+		    (ixgbe_device_supports_autoneg_fc(hw) == 0)) {
+		hw->phy.ops.write_reg(hw, MDIO_AN_ADVERTISE,
+				      MDIO_MMD_AN, reg_cu);
+	}
+
+	hw_dbg(hw, "Set up FC; IXGBE_AUTOC = 0x%08X\n", reg);
+out:
+	return ret_val;
+}
+
+/**
  *  ixgbe_start_hw_generic - Prepare hardware for Tx/Rx
  *  @hw: pointer to hardware structure
  *
@@ -2043,63 +2246,52 @@ out:
 }
 
 /**
- *  ixgbe_fc_autoneg - Configure flow control
+ *  ixgbe_negotiate_fc - Negotiate flow control
  *  @hw: pointer to hardware structure
+ *  @adv_reg: flow control advertised settings
+ *  @lp_reg: link partner's flow control settings
+ *  @adv_sym: symmetric pause bit in advertisement
+ *  @adv_asm: asymmetric pause bit in advertisement
+ *  @lp_sym: symmetric pause bit in link partner advertisement
+ *  @lp_asm: asymmetric pause bit in link partner advertisement
  *
- *  Compares our advertised flow control capabilities to those advertised by
- *  our link partner, and determines the proper flow control mode to use.
+ *  Find the intersection between advertised settings and link partner's
+ *  advertised settings
  **/
-void ixgbe_fc_autoneg(struct ixgbe_hw *hw)
+static s32 ixgbe_negotiate_fc(struct ixgbe_hw *hw, u32 adv_reg, u32 lp_reg,
+			      u32 adv_sym, u32 adv_asm, u32 lp_sym, u32 lp_asm)
 {
-	s32 ret_val = IXGBE_ERR_FC_NOT_NEGOTIATED;
-	ixgbe_link_speed speed;
-	bool link_up;
-
-	/*
-	 * AN should have completed when the cable was plugged in.
-	 * Look for reasons to bail out.  Bail out if:
-	 * - FC autoneg is disabled, or if
-	 * - link is not up.
-	 *
-	 * Since we're being called from an LSC, link is already known to be up.
-	 * So use link_up_wait_to_complete=false.
-	 */
-	if (hw->fc.disable_fc_autoneg)
-		goto out;
-
-	hw->mac.ops.check_link(hw, &speed, &link_up, false);
-	if (!link_up)
-		goto out;
-
-	switch (hw->phy.media_type) {
-	/* Autoneg flow control on fiber adapters */
-	case ixgbe_media_type_fiber:
-		if (speed == IXGBE_LINK_SPEED_1GB_FULL)
-			ret_val = ixgbe_fc_autoneg_fiber(hw);
-		break;
-
-	/* Autoneg flow control on backplane adapters */
-	case ixgbe_media_type_backplane:
-		ret_val = ixgbe_fc_autoneg_backplane(hw);
-		break;
-
-	/* Autoneg flow control on copper adapters */
-	case ixgbe_media_type_copper:
-		if (ixgbe_device_supports_autoneg_fc(hw) == 0)
-			ret_val = ixgbe_fc_autoneg_copper(hw);
-		break;
-
-	default:
-		break;
-	}
+	if ((!(adv_reg)) ||  (!(lp_reg)))
+		return IXGBE_ERR_FC_NOT_NEGOTIATED;
 
-out:
-	if (ret_val == 0) {
-		hw->fc.fc_was_autonegged = true;
+	if ((adv_reg & adv_sym) && (lp_reg & lp_sym)) {
+		/*
+		 * Now we need to check if the user selected Rx ONLY
+		 * of pause frames.  In this case, we had to advertise
+		 * FULL flow control because we could not advertise RX
+		 * ONLY. Hence, we must now check to see if we need to
+		 * turn OFF the TRANSMISSION of PAUSE frames.
+		 */
+		if (hw->fc.requested_mode == ixgbe_fc_full) {
+			hw->fc.current_mode = ixgbe_fc_full;
+			hw_dbg(hw, "Flow Control = FULL.\n");
+		} else {
+			hw->fc.current_mode = ixgbe_fc_rx_pause;
+			hw_dbg(hw, "Flow Control=RX PAUSE frames only\n");
+		}
+	} else if (!(adv_reg & adv_sym) && (adv_reg & adv_asm) &&
+		   (lp_reg & lp_sym) && (lp_reg & lp_asm)) {
+		hw->fc.current_mode = ixgbe_fc_tx_pause;
+		hw_dbg(hw, "Flow Control = TX PAUSE frames only.\n");
+	} else if ((adv_reg & adv_sym) && (adv_reg & adv_asm) &&
+		   !(lp_reg & lp_sym) && (lp_reg & lp_asm)) {
+		hw->fc.current_mode = ixgbe_fc_rx_pause;
+		hw_dbg(hw, "Flow Control = RX PAUSE frames only.\n");
 	} else {
-		hw->fc.fc_was_autonegged = false;
-		hw->fc.current_mode = hw->fc.requested_mode;
+		hw->fc.current_mode = ixgbe_fc_none;
+		hw_dbg(hw, "Flow Control = NONE.\n");
 	}
+	return 0;
 }
 
 /**
@@ -2202,241 +2394,63 @@ static s32 ixgbe_fc_autoneg_copper(struct ixgbe_hw *hw)
 }
 
 /**
- *  ixgbe_negotiate_fc - Negotiate flow control
- *  @hw: pointer to hardware structure
- *  @adv_reg: flow control advertised settings
- *  @lp_reg: link partner's flow control settings
- *  @adv_sym: symmetric pause bit in advertisement
- *  @adv_asm: asymmetric pause bit in advertisement
- *  @lp_sym: symmetric pause bit in link partner advertisement
- *  @lp_asm: asymmetric pause bit in link partner advertisement
- *
- *  Find the intersection between advertised settings and link partner's
- *  advertised settings
- **/
-static s32 ixgbe_negotiate_fc(struct ixgbe_hw *hw, u32 adv_reg, u32 lp_reg,
-			      u32 adv_sym, u32 adv_asm, u32 lp_sym, u32 lp_asm)
-{
-	if ((!(adv_reg)) ||  (!(lp_reg)))
-		return IXGBE_ERR_FC_NOT_NEGOTIATED;
-
-	if ((adv_reg & adv_sym) && (lp_reg & lp_sym)) {
-		/*
-		 * Now we need to check if the user selected Rx ONLY
-		 * of pause frames.  In this case, we had to advertise
-		 * FULL flow control because we could not advertise RX
-		 * ONLY. Hence, we must now check to see if we need to
-		 * turn OFF the TRANSMISSION of PAUSE frames.
-		 */
-		if (hw->fc.requested_mode == ixgbe_fc_full) {
-			hw->fc.current_mode = ixgbe_fc_full;
-			hw_dbg(hw, "Flow Control = FULL.\n");
-		} else {
-			hw->fc.current_mode = ixgbe_fc_rx_pause;
-			hw_dbg(hw, "Flow Control=RX PAUSE frames only\n");
-		}
-	} else if (!(adv_reg & adv_sym) && (adv_reg & adv_asm) &&
-		   (lp_reg & lp_sym) && (lp_reg & lp_asm)) {
-		hw->fc.current_mode = ixgbe_fc_tx_pause;
-		hw_dbg(hw, "Flow Control = TX PAUSE frames only.\n");
-	} else if ((adv_reg & adv_sym) && (adv_reg & adv_asm) &&
-		   !(lp_reg & lp_sym) && (lp_reg & lp_asm)) {
-		hw->fc.current_mode = ixgbe_fc_rx_pause;
-		hw_dbg(hw, "Flow Control = RX PAUSE frames only.\n");
-	} else {
-		hw->fc.current_mode = ixgbe_fc_none;
-		hw_dbg(hw, "Flow Control = NONE.\n");
-	}
-	return 0;
-}
-
-/**
- *  ixgbe_setup_fc - Set up flow control
+ *  ixgbe_fc_autoneg - Configure flow control
  *  @hw: pointer to hardware structure
  *
- *  Called at init time to set up flow control.
+ *  Compares our advertised flow control capabilities to those advertised by
+ *  our link partner, and determines the proper flow control mode to use.
  **/
-static s32 ixgbe_setup_fc(struct ixgbe_hw *hw, s32 packetbuf_num)
+void ixgbe_fc_autoneg(struct ixgbe_hw *hw)
 {
-	s32 ret_val = 0;
-	u32 reg = 0, reg_bp = 0;
-	u16 reg_cu = 0;
-
-#ifdef CONFIG_DCB
-	if (hw->fc.requested_mode == ixgbe_fc_pfc) {
-		hw->fc.current_mode = hw->fc.requested_mode;
-		goto out;
-	}
-
-#endif /* CONFIG_DCB */
-	/* Validate the packetbuf configuration */
-	if (packetbuf_num < 0 || packetbuf_num > 7) {
-		hw_dbg(hw, "Invalid packet buffer number [%d], expected range "
-		       "is 0-7\n", packetbuf_num);
-		ret_val = IXGBE_ERR_INVALID_LINK_SETTINGS;
-		goto out;
-	}
+	s32 ret_val = IXGBE_ERR_FC_NOT_NEGOTIATED;
+	ixgbe_link_speed speed;
+	bool link_up;
 
 	/*
-	 * Validate the water mark configuration.  Zero water marks are invalid
-	 * because it causes the controller to just blast out fc packets.
+	 * AN should have completed when the cable was plugged in.
+	 * Look for reasons to bail out.  Bail out if:
+	 * - FC autoneg is disabled, or if
+	 * - link is not up.
+	 *
+	 * Since we're being called from an LSC, link is already known to be up.
+	 * So use link_up_wait_to_complete=false.
 	 */
-	if (!hw->fc.low_water ||
-	    !hw->fc.high_water[packetbuf_num] ||
-	    !hw->fc.pause_time) {
-		hw_dbg(hw, "Invalid water mark configuration\n");
-		ret_val = IXGBE_ERR_INVALID_LINK_SETTINGS;
+	if (hw->fc.disable_fc_autoneg)
 		goto out;
-	}
 
-	/*
-	 * Validate the requested mode.  Strict IEEE mode does not allow
-	 * ixgbe_fc_rx_pause because it will cause us to fail at UNH.
-	 */
-	if (hw->fc.strict_ieee && hw->fc.requested_mode == ixgbe_fc_rx_pause) {
-		hw_dbg(hw, "ixgbe_fc_rx_pause not valid in strict "
-		       "IEEE mode\n");
-		ret_val = IXGBE_ERR_INVALID_LINK_SETTINGS;
+	hw->mac.ops.check_link(hw, &speed, &link_up, false);
+	if (!link_up)
 		goto out;
-	}
-
-	/*
-	 * 10gig parts do not have a word in the EEPROM to determine the
-	 * default flow control setting, so we explicitly set it to full.
-	 */
-	if (hw->fc.requested_mode == ixgbe_fc_default)
-		hw->fc.requested_mode = ixgbe_fc_full;
-
-	/*
-	 * Set up the 1G and 10G flow control advertisement registers so the
-	 * HW will be able to do fc autoneg once the cable is plugged in.  If
-	 * we link at 10G, the 1G advertisement is harmless and vice versa.
-	 */
 
 	switch (hw->phy.media_type) {
+	/* Autoneg flow control on fiber adapters */
 	case ixgbe_media_type_fiber:
+		if (speed == IXGBE_LINK_SPEED_1GB_FULL)
+			ret_val = ixgbe_fc_autoneg_fiber(hw);
+		break;
+
+	/* Autoneg flow control on backplane adapters */
 	case ixgbe_media_type_backplane:
-		reg = IXGBE_READ_REG(hw, IXGBE_PCS1GANA);
-		reg_bp = IXGBE_READ_REG(hw, IXGBE_AUTOC);
+		ret_val = ixgbe_fc_autoneg_backplane(hw);
 		break;
 
+	/* Autoneg flow control on copper adapters */
 	case ixgbe_media_type_copper:
-		hw->phy.ops.read_reg(hw, MDIO_AN_ADVERTISE,
-					MDIO_MMD_AN, &reg_cu);
+		if (ixgbe_device_supports_autoneg_fc(hw) == 0)
+			ret_val = ixgbe_fc_autoneg_copper(hw);
 		break;
 
 	default:
-		;
-	}
-
-	/*
-	 * The possible values of fc.requested_mode are:
-	 * 0: Flow control is completely disabled
-	 * 1: Rx flow control is enabled (we can receive pause frames,
-	 *    but not send pause frames).
-	 * 2: Tx flow control is enabled (we can send pause frames but
-	 *    we do not support receiving pause frames).
-	 * 3: Both Rx and Tx flow control (symmetric) are enabled.
-#ifdef CONFIG_DCB
-	 * 4: Priority Flow Control is enabled.
-#endif
-	 * other: Invalid.
-	 */
-	switch (hw->fc.requested_mode) {
-	case ixgbe_fc_none:
-		/* Flow control completely disabled by software override. */
-		reg &= ~(IXGBE_PCS1GANA_SYM_PAUSE | IXGBE_PCS1GANA_ASM_PAUSE);
-		if (hw->phy.media_type == ixgbe_media_type_backplane)
-			reg_bp &= ~(IXGBE_AUTOC_SYM_PAUSE |
-				    IXGBE_AUTOC_ASM_PAUSE);
-		else if (hw->phy.media_type == ixgbe_media_type_copper)
-			reg_cu &= ~(IXGBE_TAF_SYM_PAUSE | IXGBE_TAF_ASM_PAUSE);
-		break;
-	case ixgbe_fc_rx_pause:
-		/*
-		 * Rx Flow control is enabled and Tx Flow control is
-		 * disabled by software override. Since there really
-		 * isn't a way to advertise that we are capable of RX
-		 * Pause ONLY, we will advertise that we support both
-		 * symmetric and asymmetric Rx PAUSE.  Later, we will
-		 * disable the adapter's ability to send PAUSE frames.
-		 */
-		reg |= (IXGBE_PCS1GANA_SYM_PAUSE | IXGBE_PCS1GANA_ASM_PAUSE);
-		if (hw->phy.media_type == ixgbe_media_type_backplane)
-			reg_bp |= (IXGBE_AUTOC_SYM_PAUSE |
-				   IXGBE_AUTOC_ASM_PAUSE);
-		else if (hw->phy.media_type == ixgbe_media_type_copper)
-			reg_cu |= (IXGBE_TAF_SYM_PAUSE | IXGBE_TAF_ASM_PAUSE);
-		break;
-	case ixgbe_fc_tx_pause:
-		/*
-		 * Tx Flow control is enabled, and Rx Flow control is
-		 * disabled by software override.
-		 */
-		reg |= (IXGBE_PCS1GANA_ASM_PAUSE);
-		reg &= ~(IXGBE_PCS1GANA_SYM_PAUSE);
-		if (hw->phy.media_type == ixgbe_media_type_backplane) {
-			reg_bp |= (IXGBE_AUTOC_ASM_PAUSE);
-			reg_bp &= ~(IXGBE_AUTOC_SYM_PAUSE);
-		} else if (hw->phy.media_type == ixgbe_media_type_copper) {
-			reg_cu |= (IXGBE_TAF_ASM_PAUSE);
-			reg_cu &= ~(IXGBE_TAF_SYM_PAUSE);
-		}
-		break;
-	case ixgbe_fc_full:
-		/* Flow control (both Rx and Tx) is enabled by SW override. */
-		reg |= (IXGBE_PCS1GANA_SYM_PAUSE | IXGBE_PCS1GANA_ASM_PAUSE);
-		if (hw->phy.media_type == ixgbe_media_type_backplane)
-			reg_bp |= (IXGBE_AUTOC_SYM_PAUSE |
-				   IXGBE_AUTOC_ASM_PAUSE);
-		else if (hw->phy.media_type == ixgbe_media_type_copper)
-			reg_cu |= (IXGBE_TAF_SYM_PAUSE | IXGBE_TAF_ASM_PAUSE);
-		break;
-#ifdef CONFIG_DCB
-	case ixgbe_fc_pfc:
-		goto out;
-		break;
-#endif /* CONFIG_DCB */
-	default:
-		hw_dbg(hw, "Flow control param set incorrectly\n");
-		ret_val = IXGBE_ERR_CONFIG;
-		goto out;
 		break;
 	}
 
-	if (hw->mac.type != ixgbe_mac_X540) {
-		/*
-		 * Enable auto-negotiation between the MAC & PHY;
-		 * the MAC will advertise clause 37 flow control.
-		 */
-		IXGBE_WRITE_REG(hw, IXGBE_PCS1GANA, reg);
-		reg = IXGBE_READ_REG(hw, IXGBE_PCS1GLCTL);
-
-		/* Disable AN timeout */
-		if (hw->fc.strict_ieee)
-			reg &= ~IXGBE_PCS1GLCTL_AN_1G_TIMEOUT_EN;
-
-		IXGBE_WRITE_REG(hw, IXGBE_PCS1GLCTL, reg);
-		hw_dbg(hw, "Set up FC; PCS1GLCTL = 0x%08X\n", reg);
-	}
-
-	/*
-	 * AUTOC restart handles negotiation of 1G and 10G on backplane
-	 * and copper. There is no need to set the PCS1GCTL register.
-	 *
-	 */
-	if (hw->phy.media_type == ixgbe_media_type_backplane) {
-		reg_bp |= IXGBE_AUTOC_AN_RESTART;
-		IXGBE_WRITE_REG(hw, IXGBE_AUTOC, reg_bp);
-	} else if ((hw->phy.media_type == ixgbe_media_type_copper) &&
-		    (ixgbe_device_supports_autoneg_fc(hw) == 0)) {
-		hw->phy.ops.write_reg(hw, MDIO_AN_ADVERTISE,
-				      MDIO_MMD_AN, reg_cu);
-	}
-
-	hw_dbg(hw, "Set up FC; IXGBE_AUTOC = 0x%08X\n", reg);
 out:
-	return ret_val;
+	if (ret_val == 0) {
+		hw->fc.fc_was_autonegged = true;
+	} else {
+		hw->fc.fc_was_autonegged = false;
+		hw->fc.current_mode = hw->fc.requested_mode;
+	}
 }
 
 /**
@@ -3207,28 +3221,6 @@ wwn_prefix_out:
 }
 
 /**
- *  ixgbe_device_supports_autoneg_fc - Check if phy supports autoneg flow
- *  control
- *  @hw: pointer to hardware structure
- *
- *  There are several phys that do not support autoneg flow control. This
- *  function check the device id to see if the associated phy supports
- *  autoneg flow control.
- **/
-static s32 ixgbe_device_supports_autoneg_fc(struct ixgbe_hw *hw)
-{
-
-	switch (hw->device_id) {
-	case IXGBE_DEV_ID_X540T:
-		return 0;
-	case IXGBE_DEV_ID_82599_T3_LOM:
-		return 0;
-	default:
-		return IXGBE_ERR_FC_NOT_SUPPORTED;
-	}
-}
-
-/**
  *  ixgbe_set_mac_anti_spoofing - Enable/Disable MAC anti-spoofing
  *  @hw: pointer to hardware structure
  *  @enable: enable or disable switch for anti-spoofing