auxdisplay: Move panel.c to drivers/auxdisplay folder

It looks like panel.c belongs to auxdisplay subsystem.

Move it to drivers/auxdisplay folder.
No functional changes intended.

Acked-by: Geert Uytterhoeven <geert@linux-m68k.org>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

1 files changed, 0 insertions, 280 deletions

diff --git a/drivers/misc/Kconfig b/drivers/misc/Kconfig
index fb933b0b9297..2438466c15ac 100644
--- a/drivers/misc/Kconfig
+++ b/drivers/misc/Kconfig
@@ -492,286 +492,6 @@ config VEXPRESS_SYSCFG
 	  bus. System Configuration interface is one of the possible means
 	  of generating transactions on this bus.
 
-config PANEL
-	tristate "Parallel port LCD/Keypad Panel support"
-	depends on PARPORT
-	select CHARLCD
-	---help---
-	  Say Y here if you have an HD44780 or KS-0074 LCD connected to your
-	  parallel port. This driver also features 4 and 6-key keypads. The LCD
-	  is accessible through the /dev/lcd char device (10, 156), and the
-	  keypad through /dev/keypad (10, 185). This code can either be
-	  compiled as a module, or linked into the kernel and started at boot.
-	  If you don't understand what all this is about, say N.
-
-if PANEL
-
-config PANEL_PARPORT
-	int "Default parallel port number (0=LPT1)"
-	range 0 255
-	default "0"
-	---help---
-	  This is the index of the parallel port the panel is connected to. One
-	  driver instance only supports one parallel port, so if your keypad
-	  and LCD are connected to two separate ports, you have to start two
-	  modules with different arguments. Numbering starts with '0' for LPT1,
-	  and so on.
-
-config PANEL_PROFILE
-	int "Default panel profile (0-5, 0=custom)"
-	range 0 5
-	default "5"
-	---help---
-	  To ease configuration, the driver supports different configuration
-	  profiles for past and recent wirings. These profiles can also be
-	  used to define an approximative configuration, completed by a few
-	  other options. Here are the profiles :
-
-	    0 = custom (see further)
-	    1 = 2x16 parallel LCD, old keypad
-	    2 = 2x16 serial LCD (KS-0074), new keypad
-	    3 = 2x16 parallel LCD (Hantronix), no keypad
-	    4 = 2x16 parallel LCD (Nexcom NSA1045) with Nexcom's keypad
-	    5 = 2x40 parallel LCD (old one), with old keypad
-
-	  Custom configurations allow you to define how your display is
-	  wired to the parallel port, and how it works. This is only intended
-	  for experts.
-
-config PANEL_KEYPAD
-	depends on PANEL_PROFILE="0"
-	int "Keypad type (0=none, 1=old 6 keys, 2=new 6 keys, 3=Nexcom 4 keys)"
-	range 0 3
-	default 0
-	---help---
-	  This enables and configures a keypad connected to the parallel port.
-	  The keys will be read from character device 10,185. Valid values are :
-
-	    0 : do not enable this driver
-	    1 : old 6 keys keypad
-	    2 : new 6 keys keypad, as used on the server at www.ant-computing.com
-	    3 : Nexcom NSA1045's 4 keys keypad
-
-	  New profiles can be described in the driver source. The driver also
-	  supports simultaneous keys pressed when the keypad supports them.
-
-config PANEL_LCD
-	depends on PANEL_PROFILE="0"
-	int "LCD type (0=none, 1=custom, 2=old //, 3=ks0074, 4=hantronix, 5=Nexcom)"
-	range 0 5
-	default 0
-	---help---
-	   This enables and configures an LCD connected to the parallel port.
-	   The driver includes an interpreter for escape codes starting with
-	   '\e[L' which are specific to the LCD, and a few ANSI codes. The
-	   driver will be registered as character device 10,156, usually
-	   under the name '/dev/lcd'. There are a total of 6 supported types :
-
-	     0 : do not enable the driver
-	     1 : custom configuration and wiring (see further)
-	     2 : 2x16 & 2x40 parallel LCD (old wiring)
-	     3 : 2x16 serial LCD (KS-0074 based)
-	     4 : 2x16 parallel LCD (Hantronix wiring)
-	     5 : 2x16 parallel LCD (Nexcom wiring)
-
-	   When type '1' is specified, other options will appear to configure
-	   more precise aspects (wiring, dimensions, protocol, ...). Please note
-	   that those values changed from the 2.4 driver for better consistency.
-
-config PANEL_LCD_HEIGHT
-	depends on PANEL_PROFILE="0" && PANEL_LCD="1"
-	int "Number of lines on the LCD (1-2)"
-	range 1 2
-	default 2
-	---help---
-	  This is the number of visible character lines on the LCD in custom profile.
-	  It can either be 1 or 2.
-
-config PANEL_LCD_WIDTH
-	depends on PANEL_PROFILE="0" && PANEL_LCD="1"
-	int "Number of characters per line on the LCD (1-40)"
-	range 1 40
-	default 40
-	---help---
-	  This is the number of characters per line on the LCD in custom profile.
-	  Common values are 16,20,24,40.
-
-config PANEL_LCD_BWIDTH
-	depends on PANEL_PROFILE="0" && PANEL_LCD="1"
-	int "Internal LCD line width (1-40, 40 by default)"
-	range 1 40
-	default 40
-	---help---
-	  Most LCDs use a standard controller which supports hardware lines of 40
-	  characters, although sometimes only 16, 20 or 24 of them are really wired
-	  to the terminal. This results in some non-visible but addressable characters,
-	  and is the case for most parallel LCDs. Other LCDs, and some serial ones,
-	  however, use the same line width internally as what is visible. The KS0074
-	  for example, uses 16 characters per line for 16 visible characters per line.
-
-	  This option lets you configure the value used by your LCD in 'custom' profile.
-	  If you don't know, put '40' here.
-
-config PANEL_LCD_HWIDTH
-	depends on PANEL_PROFILE="0" && PANEL_LCD="1"
-	int "Hardware LCD line width (1-64, 64 by default)"
-	range 1 64
-	default 64
-	---help---
-	  Most LCDs use a single address bit to differentiate line 0 and line 1. Since
-	  some of them need to be able to address 40 chars with the lower bits, they
-	  often use the immediately superior power of 2, which is 64, to address the
-	  next line.
-
-	  If you don't know what your LCD uses, in doubt let 16 here for a 2x16, and
-	  64 here for a 2x40.
-
-config PANEL_LCD_CHARSET
-	depends on PANEL_PROFILE="0" && PANEL_LCD="1"
-	int "LCD character set (0=normal, 1=KS0074)"
-	range 0 1
-	default 0
-	---help---
-	  Some controllers such as the KS0074 use a somewhat strange character set
-	  where many symbols are at unusual places. The driver knows how to map
-	  'standard' ASCII characters to the character sets used by these controllers.
-	  Valid values are :
-
-	     0 : normal (untranslated) character set
-	     1 : KS0074 character set
-
-	  If you don't know, use the normal one (0).
-
-config PANEL_LCD_PROTO
-	depends on PANEL_PROFILE="0" && PANEL_LCD="1"
-	int "LCD communication mode (0=parallel 8 bits, 1=serial)"
-	range 0 1
-	default 0
-	---help---
-	  This driver now supports any serial or parallel LCD wired to a parallel
-	  port. But before assigning signals, the driver needs to know if it will
-	  be driving a serial LCD or a parallel one. Serial LCDs only use 2 wires
-	  (SDA/SCL), while parallel ones use 2 or 3 wires for the control signals
-	  (E, RS, sometimes RW), and 4 or 8 for the data. Use 0 here for a 8 bits
-	  parallel LCD, and 1 for a serial LCD.
-
-config PANEL_LCD_PIN_E
-	depends on PANEL_PROFILE="0" && PANEL_LCD="1" && PANEL_LCD_PROTO="0"
-        int "Parallel port pin number & polarity connected to the LCD E signal (-17...17) "
-	range -17 17
-	default 14
-	---help---
-	  This describes the number of the parallel port pin to which the LCD 'E'
-	  signal has been connected. It can be :
-
-	          0 : no connection (eg: connected to ground)
-	      1..17 : directly connected to any of these pins on the DB25 plug
-	    -1..-17 : connected to the same pin through an inverter (eg: transistor).
-
-	  Default for the 'E' pin in custom profile is '14' (AUTOFEED).
-
-config PANEL_LCD_PIN_RS
-	depends on PANEL_PROFILE="0" && PANEL_LCD="1" && PANEL_LCD_PROTO="0"
-        int "Parallel port pin number & polarity connected to the LCD RS signal (-17...17) "
-	range -17 17
-	default 17
-	---help---
-	  This describes the number of the parallel port pin to which the LCD 'RS'
-	  signal has been connected. It can be :
-
-	          0 : no connection (eg: connected to ground)
-	      1..17 : directly connected to any of these pins on the DB25 plug
-	    -1..-17 : connected to the same pin through an inverter (eg: transistor).
-
-	  Default for the 'RS' pin in custom profile is '17' (SELECT IN).
-
-config PANEL_LCD_PIN_RW
-	depends on PANEL_PROFILE="0" && PANEL_LCD="1" && PANEL_LCD_PROTO="0"
-        int "Parallel port pin number & polarity connected to the LCD RW signal (-17...17) "
-	range -17 17
-	default 16
-	---help---
-	  This describes the number of the parallel port pin to which the LCD 'RW'
-	  signal has been connected. It can be :
-
-	          0 : no connection (eg: connected to ground)
-	      1..17 : directly connected to any of these pins on the DB25 plug
-	    -1..-17 : connected to the same pin through an inverter (eg: transistor).
-
-	  Default for the 'RW' pin in custom profile is '16' (INIT).
-
-config PANEL_LCD_PIN_SCL
-	depends on PANEL_PROFILE="0" && PANEL_LCD="1" && PANEL_LCD_PROTO!="0"
-        int "Parallel port pin number & polarity connected to the LCD SCL signal (-17...17) "
-	range -17 17
-	default 1
-	---help---
-	  This describes the number of the parallel port pin to which the serial
-	  LCD 'SCL' signal has been connected. It can be :
-
-	          0 : no connection (eg: connected to ground)
-	      1..17 : directly connected to any of these pins on the DB25 plug
-	    -1..-17 : connected to the same pin through an inverter (eg: transistor).
-
-	  Default for the 'SCL' pin in custom profile is '1' (STROBE).
-
-config PANEL_LCD_PIN_SDA
-	depends on PANEL_PROFILE="0" && PANEL_LCD="1" && PANEL_LCD_PROTO!="0"
-        int "Parallel port pin number & polarity connected to the LCD SDA signal (-17...17) "
-	range -17 17
-	default 2
-	---help---
-	  This describes the number of the parallel port pin to which the serial
-	  LCD 'SDA' signal has been connected. It can be :
-
-	          0 : no connection (eg: connected to ground)
-	      1..17 : directly connected to any of these pins on the DB25 plug
-	    -1..-17 : connected to the same pin through an inverter (eg: transistor).
-
-	  Default for the 'SDA' pin in custom profile is '2' (D0).
-
-config PANEL_LCD_PIN_BL
-	depends on PANEL_PROFILE="0" && PANEL_LCD="1"
-        int "Parallel port pin number & polarity connected to the LCD backlight signal (-17...17) "
-	range -17 17
-	default 0
-	---help---
-	  This describes the number of the parallel port pin to which the LCD 'BL' signal
-          has been connected. It can be :
-
-	          0 : no connection (eg: connected to ground)
-	      1..17 : directly connected to any of these pins on the DB25 plug
-	    -1..-17 : connected to the same pin through an inverter (eg: transistor).
-
-	  Default for the 'BL' pin in custom profile is '0' (uncontrolled).
-
-config PANEL_CHANGE_MESSAGE
-	bool "Change LCD initialization message ?"
-	default "n"
-	---help---
-	  This allows you to replace the boot message indicating the kernel version
-	  and the driver version with a custom message. This is useful on appliances
-	  where a simple 'Starting system' message can be enough to stop a customer
-	  from worrying.
-
-	  If you say 'Y' here, you'll be able to choose a message yourself. Otherwise,
-	  say 'N' and keep the default message with the version.
-
-config PANEL_BOOT_MESSAGE
-	depends on PANEL_CHANGE_MESSAGE="y"
-	string "New initialization message"
-	default ""
-	---help---
-	  This allows you to replace the boot message indicating the kernel version
-	  and the driver version with a custom message. This is useful on appliances
-	  where a simple 'Starting system' message can be enough to stop a customer
-	  from worrying.
-
-	  An empty message will only clear the display at driver init time. Any other
-	  printf()-formatted message is valid with newline and escape codes.
-
-endif # PANEL
-
 config ASPEED_LPC_CTRL
 	depends on (ARCH_ASPEED || COMPILE_TEST) && REGMAP && MFD_SYSCON
 	tristate "Aspeed ast2400/2500 HOST LPC to BMC bridge control"