Merge tag 'armsoc-drivers' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc

Pull ARM SoC driver updates from Olof Johansson:
 "Various driver updates for platforms:

   - A larger set of work on Tegra 2/3 around memory controller and
     regulator features, some fuse cleanups, etc..

   - MMP platform drivers, in particular for USB PHY, and other smaller
     additions.

   - Samsung Exynos 5422 driver for DMC (dynamic memory configuration),
     and ASV (adaptive voltage), allowing the platform to run at more
     optimal operating points.

   - Misc refactorings and support for RZ/G2N and R8A774B1 from Renesas

   - Clock/reset control driver for TI/OMAP

   - Meson-A1 reset controller support

   - Qualcomm sdm845 and sda845 SoC IDs for socinfo"

* tag 'armsoc-drivers' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc: (150 commits)
  firmware: arm_scmi: Fix doorbell ring logic for !CONFIG_64BIT
  soc: fsl: add RCPM driver
  dt-bindings: fsl: rcpm: Add 'little-endian' and update Chassis definition
  memory: tegra: Consolidate registers definition into common header
  memory: tegra: Ensure timing control debug features are disabled
  memory: tegra: Introduce Tegra30 EMC driver
  memory: tegra: Do not handle error from wait_for_completion_timeout()
  memory: tegra: Increase handshake timeout on Tegra20
  memory: tegra: Print a brief info message about EMC timings
  memory: tegra: Pre-configure debug register on Tegra20
  memory: tegra: Include io.h instead of iopoll.h
  memory: tegra: Adapt for Tegra20 clock driver changes
  memory: tegra: Don't set EMC rate to maximum on probe for Tegra20
  memory: tegra: Add gr2d and gr3d to DRM IOMMU group
  memory: tegra: Set DMA mask based on supported address bits
  soc: at91: Add Atmel SFR SN (Serial Number) support
  memory: atmel-ebi: switch to SPDX license identifiers
  memory: atmel-ebi: move NUM_CS definition inside EBI driver
  soc: mediatek: Refactor bus protection control
  soc: mediatek: Refactor sram control
  ...

18 files changed, 3327 insertions, 222 deletions

diff --git a/drivers/memory/atmel-ebi.c b/drivers/memory/atmel-ebi.c
index 0322df9dc249..14386d0b5f57 100644
--- a/drivers/memory/atmel-ebi.c
+++ b/drivers/memory/atmel-ebi.c
@@ -1,12 +1,9 @@
+// SPDX-License-Identifier: GPL-2.0
 /*
  * EBI driver for Atmel chips
  * inspired by the fsl weim bus driver
  *
  * Copyright (C) 2013 Jean-Jacques Hiblot <jjhiblot@traphandler.com>
- *
- * This file is licensed under the terms of the GNU General Public
- * License version 2. This program is licensed "as is" without any
- * warranty of any kind, whether express or implied.
  */
 
 #include <linux/clk.h>
@@ -19,6 +16,8 @@
 #include <linux/regmap.h>
 #include <soc/at91/atmel-sfr.h>
 
+#define AT91_EBI_NUM_CS		8
+
 struct atmel_ebi_dev_config {
 	int cs;
 	struct atmel_smc_cs_conf smcconf;
@@ -314,7 +313,7 @@ static int atmel_ebi_dev_setup(struct atmel_ebi *ebi, struct device_node *np,
 		if (ret)
 			return ret;
 
-		if (cs >= AT91_MATRIX_EBI_NUM_CS ||
+		if (cs >= AT91_EBI_NUM_CS ||
 		    !(ebi->caps->available_cs & BIT(cs))) {
 			dev_err(dev, "invalid reg property in %pOF\n", np);
 			return -EINVAL;
@@ -344,7 +343,7 @@ static int atmel_ebi_dev_setup(struct atmel_ebi *ebi, struct device_node *np,
 		apply = true;
 
 	i = 0;
-	for_each_set_bit(cs, &cslines, AT91_MATRIX_EBI_NUM_CS) {
+	for_each_set_bit(cs, &cslines, AT91_EBI_NUM_CS) {
 		ebid->configs[i].cs = cs;
 
 		if (apply) {
diff --git a/drivers/memory/brcmstb_dpfe.c b/drivers/memory/brcmstb_dpfe.c
index 6827ed484750..82b415be18d1 100644
--- a/drivers/memory/brcmstb_dpfe.c
+++ b/drivers/memory/brcmstb_dpfe.c
@@ -127,7 +127,6 @@ enum dpfe_msg_fields {
 	MSG_COMMAND,
 	MSG_ARG_COUNT,
 	MSG_ARG0,
-	MSG_CHKSUM,
 	MSG_FIELD_MAX	= 16 /* Max number of arguments */
 };
 
@@ -180,7 +179,7 @@ struct dpfe_api {
 };
 
 /* Things we need for as long as we are active. */
-struct private_data {
+struct brcmstb_dpfe_priv {
 	void __iomem *regs;
 	void __iomem *dmem;
 	void __iomem *imem;
@@ -232,9 +231,13 @@ static struct attribute *dpfe_v3_attrs[] = {
 };
 ATTRIBUTE_GROUPS(dpfe_v3);
 
-/* API v2 firmware commands */
-static const struct dpfe_api dpfe_api_v2 = {
-	.version = 2,
+/*
+ * Old API v2 firmware commands, as defined in the rev 0.61 specification, we
+ * use a version set to 1 to denote that it is not compatible with the new API
+ * v2 and onwards.
+ */
+static const struct dpfe_api dpfe_api_old_v2 = {
+	.version = 1,
 	.fw_name = "dpfe.bin",
 	.sysfs_attrs = dpfe_v2_groups,
 	.command = {
@@ -243,21 +246,42 @@ static const struct dpfe_api dpfe_api_v2 = {
 			[MSG_COMMAND] = 1,
 			[MSG_ARG_COUNT] = 1,
 			[MSG_ARG0] = 1,
-			[MSG_CHKSUM] = 4,
 		},
 		[DPFE_CMD_GET_REFRESH] = {
 			[MSG_HEADER] = DPFE_MSG_TYPE_COMMAND,
 			[MSG_COMMAND] = 2,
 			[MSG_ARG_COUNT] = 1,
 			[MSG_ARG0] = 1,
-			[MSG_CHKSUM] = 5,
 		},
 		[DPFE_CMD_GET_VENDOR] = {
 			[MSG_HEADER] = DPFE_MSG_TYPE_COMMAND,
 			[MSG_COMMAND] = 2,
 			[MSG_ARG_COUNT] = 1,
 			[MSG_ARG0] = 2,
-			[MSG_CHKSUM] = 6,
+		},
+	}
+};
+
+/*
+ * API v2 firmware commands, as defined in the rev 0.8 specification, named new
+ * v2 here
+ */
+static const struct dpfe_api dpfe_api_new_v2 = {
+	.version = 2,
+	.fw_name = NULL, /* We expect the firmware to have been downloaded! */
+	.sysfs_attrs = dpfe_v2_groups,
+	.command = {
+		[DPFE_CMD_GET_INFO] = {
+			[MSG_HEADER] = DPFE_MSG_TYPE_COMMAND,
+			[MSG_COMMAND] = 0x101,
+		},
+		[DPFE_CMD_GET_REFRESH] = {
+			[MSG_HEADER] = DPFE_MSG_TYPE_COMMAND,
+			[MSG_COMMAND] = 0x201,
+		},
+		[DPFE_CMD_GET_VENDOR] = {
+			[MSG_HEADER] = DPFE_MSG_TYPE_COMMAND,
+			[MSG_COMMAND] = 0x202,
 		},
 	}
 };
@@ -273,49 +297,51 @@ static const struct dpfe_api dpfe_api_v3 = {
 			[MSG_COMMAND] = 0x0101,
 			[MSG_ARG_COUNT] = 1,
 			[MSG_ARG0] = 1,
-			[MSG_CHKSUM] = 0x104,
 		},
 		[DPFE_CMD_GET_REFRESH] = {
 			[MSG_HEADER] = DPFE_MSG_TYPE_COMMAND,
 			[MSG_COMMAND] = 0x0202,
 			[MSG_ARG_COUNT] = 0,
-			/*
-			 * This is a bit ugly. Without arguments, the checksum
-			 * follows right after the argument count and not at
-			 * offset MSG_CHKSUM.
-			 */
-			[MSG_ARG0] = 0x203,
 		},
 		/* There's no GET_VENDOR command in API v3. */
 	},
 };
 
-static bool is_dcpu_enabled(void __iomem *regs)
+static bool is_dcpu_enabled(struct brcmstb_dpfe_priv *priv)
 {
 	u32 val;
 
-	val = readl_relaxed(regs + REG_DCPU_RESET);
+	mutex_lock(&priv->lock);
+	val = readl_relaxed(priv->regs + REG_DCPU_RESET);
+	mutex_unlock(&priv->lock);
 
 	return !(val & DCPU_RESET_MASK);
 }
 
-static void __disable_dcpu(void __iomem *regs)
+static void __disable_dcpu(struct brcmstb_dpfe_priv *priv)
 {
 	u32 val;
 
-	if (!is_dcpu_enabled(regs))
+	if (!is_dcpu_enabled(priv))
 		return;
 
+	mutex_lock(&priv->lock);
+
 	/* Put DCPU in reset if it's running. */
-	val = readl_relaxed(regs + REG_DCPU_RESET);
+	val = readl_relaxed(priv->regs + REG_DCPU_RESET);
 	val |= (1 << DCPU_RESET_SHIFT);
-	writel_relaxed(val, regs + REG_DCPU_RESET);
+	writel_relaxed(val, priv->regs + REG_DCPU_RESET);
+
+	mutex_unlock(&priv->lock);
 }
 
-static void __enable_dcpu(void __iomem *regs)
+static void __enable_dcpu(struct brcmstb_dpfe_priv *priv)
 {
+	void __iomem *regs = priv->regs;
 	u32 val;
 
+	mutex_lock(&priv->lock);
+
 	/* Clear mailbox registers. */
 	writel_relaxed(0, regs + REG_TO_DCPU_MBOX);
 	writel_relaxed(0, regs + REG_TO_HOST_MBOX);
@@ -329,6 +355,8 @@ static void __enable_dcpu(void __iomem *regs)
 	val = readl_relaxed(regs + REG_DCPU_RESET);
 	val &= ~(1 << DCPU_RESET_SHIFT);
 	writel_relaxed(val, regs + REG_DCPU_RESET);
+
+	mutex_unlock(&priv->lock);
 }
 
 static unsigned int get_msg_chksum(const u32 msg[], unsigned int max)
@@ -343,7 +371,7 @@ static unsigned int get_msg_chksum(const u32 msg[], unsigned int max)
 	return sum;
 }
 
-static void __iomem *get_msg_ptr(struct private_data *priv, u32 response,
+static void __iomem *get_msg_ptr(struct brcmstb_dpfe_priv *priv, u32 response,
 				 char *buf, ssize_t *size)
 {
 	unsigned int msg_type;
@@ -382,7 +410,7 @@ static void __iomem *get_msg_ptr(struct private_data *priv, u32 response,
 	return ptr;
 }
 
-static void __finalize_command(struct private_data *priv)
+static void __finalize_command(struct brcmstb_dpfe_priv *priv)
 {
 	unsigned int release_mbox;
 
@@ -390,12 +418,12 @@ static void __finalize_command(struct private_data *priv)
 	 * It depends on the API version which MBOX register we have to write to
 	 * to signal we are done.
 	 */
-	release_mbox = (priv->dpfe_api->version < 3)
+	release_mbox = (priv->dpfe_api->version < 2)
 			? REG_TO_HOST_MBOX : REG_TO_DCPU_MBOX;
 	writel_relaxed(0, priv->regs + release_mbox);
 }
 
-static int __send_command(struct private_data *priv, unsigned int cmd,
+static int __send_command(struct brcmstb_dpfe_priv *priv, unsigned int cmd,
 			  u32 result[])
 {
 	const u32 *msg = priv->dpfe_api->command[cmd];
@@ -421,9 +449,17 @@ static int __send_command(struct private_data *priv, unsigned int cmd,
 		return -ETIMEDOUT;
 	}
 
+	/* Compute checksum over the message */
+	chksum_idx = msg[MSG_ARG_COUNT] + MSG_ARG_COUNT + 1;
+	chksum = get_msg_chksum(msg, chksum_idx);
+
 	/* Write command and arguments to message area */
-	for (i = 0; i < MSG_FIELD_MAX; i++)
-		writel_relaxed(msg[i], regs + DCPU_MSG_RAM(i));
+	for (i = 0; i < MSG_FIELD_MAX; i++) {
+		if (i == chksum_idx)
+			writel_relaxed(chksum, regs + DCPU_MSG_RAM(i));
+		else
+			writel_relaxed(msg[i], regs + DCPU_MSG_RAM(i));
+	}
 
 	/* Tell DCPU there is a command waiting */
 	writel_relaxed(1, regs + REG_TO_DCPU_MBOX);
@@ -517,7 +553,7 @@ static int __verify_firmware(struct init_data *init,
 
 /* Verify checksum by reading back the firmware from co-processor RAM. */
 static int __verify_fw_checksum(struct init_data *init,
-				struct private_data *priv,
+				struct brcmstb_dpfe_priv *priv,
 				const struct dpfe_firmware_header *header,
 				u32 checksum)
 {
@@ -571,26 +607,23 @@ static int __write_firmware(u32 __iomem *mem, const u32 *fw,
 	return 0;
 }
 
-static int brcmstb_dpfe_download_firmware(struct platform_device *pdev,
-					  struct init_data *init)
+static int brcmstb_dpfe_download_firmware(struct brcmstb_dpfe_priv *priv)
 {
 	const struct dpfe_firmware_header *header;
 	unsigned int dmem_size, imem_size;
-	struct device *dev = &pdev->dev;
+	struct device *dev = priv->dev;
 	bool is_big_endian = false;
-	struct private_data *priv;
 	const struct firmware *fw;
 	const u32 *dmem, *imem;
+	struct init_data init;
 	const void *fw_blob;
 	int ret;
 
-	priv = platform_get_drvdata(pdev);
-
 	/*
 	 * Skip downloading the firmware if the DCPU is already running and
 	 * responding to commands.
 	 */
-	if (is_dcpu_enabled(priv->regs)) {
+	if (is_dcpu_enabled(priv)) {
 		u32 response[MSG_FIELD_MAX];
 
 		ret = __send_command(priv, DPFE_CMD_GET_INFO, response);
@@ -606,20 +639,23 @@ static int brcmstb_dpfe_download_firmware(struct platform_device *pdev,
 	if (!priv->dpfe_api->fw_name)
 		return -ENODEV;
 
-	ret = request_firmware(&fw, priv->dpfe_api->fw_name, dev);
-	/* request_firmware() prints its own error messages. */
+	ret = firmware_request_nowarn(&fw, priv->dpfe_api->fw_name, dev);
+	/*
+	 * Defer the firmware download if the firmware file couldn't be found.
+	 * The root file system may not be available yet.
+	 */
 	if (ret)
-		return ret;
+		return (ret == -ENOENT) ? -EPROBE_DEFER : ret;
 
-	ret = __verify_firmware(init, fw);
+	ret = __verify_firmware(&init, fw);
 	if (ret)
 		return -EFAULT;
 
-	__disable_dcpu(priv->regs);
+	__disable_dcpu(priv);
 
-	is_big_endian = init->is_big_endian;
-	dmem_size = init->dmem_len;
-	imem_size = init->imem_len;
+	is_big_endian = init.is_big_endian;
+	dmem_size = init.dmem_len;
+	imem_size = init.imem_len;
 
 	/* At the beginning of the firmware blob is a header. */
 	header = (struct dpfe_firmware_header *)fw->data;
@@ -637,17 +673,17 @@ static int brcmstb_dpfe_download_firmware(struct platform_device *pdev,
 	if (ret)
 		return ret;
 
-	ret = __verify_fw_checksum(init, priv, header, init->chksum);
+	ret = __verify_fw_checksum(&init, priv, header, init.chksum);
 	if (ret)
 		return ret;
 
-	__enable_dcpu(priv->regs);
+	__enable_dcpu(priv);
 
 	return 0;
 }
 
 static ssize_t generic_show(unsigned int command, u32 response[],
-			    struct private_data *priv, char *buf)
+			    struct brcmstb_dpfe_priv *priv, char *buf)
 {
 	int ret;
 
@@ -665,7 +701,7 @@ static ssize_t show_info(struct device *dev, struct device_attribute *devattr,
 			 char *buf)
 {
 	u32 response[MSG_FIELD_MAX];
-	struct private_data *priv;
+	struct brcmstb_dpfe_priv *priv;
 	unsigned int info;
 	ssize_t ret;
 
@@ -688,7 +724,7 @@ static ssize_t show_refresh(struct device *dev,
 {
 	u32 response[MSG_FIELD_MAX];
 	void __iomem *info;
-	struct private_data *priv;
+	struct brcmstb_dpfe_priv *priv;
 	u8 refresh, sr_abort, ppre, thermal_offs, tuf;
 	u32 mr4;
 	ssize_t ret;
@@ -721,7 +757,7 @@ static ssize_t store_refresh(struct device *dev, struct device_attribute *attr,
 			  const char *buf, size_t count)
 {
 	u32 response[MSG_FIELD_MAX];
-	struct private_data *priv;
+	struct brcmstb_dpfe_priv *priv;
 	void __iomem *info;
 	unsigned long val;
 	int ret;
@@ -747,7 +783,7 @@ static ssize_t show_vendor(struct device *dev, struct device_attribute *devattr,
 			   char *buf)
 {
 	u32 response[MSG_FIELD_MAX];
-	struct private_data *priv;
+	struct brcmstb_dpfe_priv *priv;
 	void __iomem *info;
 	ssize_t ret;
 	u32 mr5, mr6, mr7, mr8, err;
@@ -778,7 +814,7 @@ static ssize_t show_dram(struct device *dev, struct device_attribute *devattr,
 			 char *buf)
 {
 	u32 response[MSG_FIELD_MAX];
-	struct private_data *priv;
+	struct brcmstb_dpfe_priv *priv;
 	ssize_t ret;
 	u32 mr4, mr5, mr6, mr7, mr8, err;
 
@@ -800,16 +836,15 @@ static ssize_t show_dram(struct device *dev, struct device_attribute *devattr,
 
 static int brcmstb_dpfe_resume(struct platform_device *pdev)
 {
-	struct init_data init;
+	struct brcmstb_dpfe_priv *priv = platform_get_drvdata(pdev);
 
-	return brcmstb_dpfe_download_firmware(pdev, &init);
+	return brcmstb_dpfe_download_firmware(priv);
 }
 
 static int brcmstb_dpfe_probe(struct platform_device *pdev)
 {
 	struct device *dev = &pdev->dev;
-	struct private_data *priv;
-	struct init_data init;
+	struct brcmstb_dpfe_priv *priv;
 	struct resource *res;
 	int ret;
 
@@ -817,6 +852,8 @@ static int brcmstb_dpfe_probe(struct platform_device *pdev)
 	if (!priv)
 		return -ENOMEM;
 
+	priv->dev = dev;
+
 	mutex_init(&priv->lock);
 	platform_set_drvdata(pdev, priv);
 
@@ -851,9 +888,10 @@ static int brcmstb_dpfe_probe(struct platform_device *pdev)
 		return -ENOENT;
 	}
 
-	ret = brcmstb_dpfe_download_firmware(pdev, &init);
+	ret = brcmstb_dpfe_download_firmware(priv);
 	if (ret) {
-		dev_err(dev, "Couldn't download firmware -- %d\n", ret);
+		if (ret != -EPROBE_DEFER)
+			dev_err(dev, "Couldn't download firmware -- %d\n", ret);
 		return ret;
 	}
 
@@ -867,7 +905,7 @@ static int brcmstb_dpfe_probe(struct platform_device *pdev)
 
 static int brcmstb_dpfe_remove(struct platform_device *pdev)
 {
-	struct private_data *priv = dev_get_drvdata(&pdev->dev);
+	struct brcmstb_dpfe_priv *priv = dev_get_drvdata(&pdev->dev);
 
 	sysfs_remove_groups(&pdev->dev.kobj, priv->dpfe_api->sysfs_attrs);
 
@@ -876,10 +914,10 @@ static int brcmstb_dpfe_remove(struct platform_device *pdev)
 
 static const struct of_device_id brcmstb_dpfe_of_match[] = {
 	/* Use legacy API v2 for a select number of chips */
-	{ .compatible = "brcm,bcm7268-dpfe-cpu", .data = &dpfe_api_v2 },
-	{ .compatible = "brcm,bcm7271-dpfe-cpu", .data = &dpfe_api_v2 },
-	{ .compatible = "brcm,bcm7278-dpfe-cpu", .data = &dpfe_api_v2 },
-	{ .compatible = "brcm,bcm7211-dpfe-cpu", .data = &dpfe_api_v2 },
+	{ .compatible = "brcm,bcm7268-dpfe-cpu", .data = &dpfe_api_old_v2 },
+	{ .compatible = "brcm,bcm7271-dpfe-cpu", .data = &dpfe_api_old_v2 },
+	{ .compatible = "brcm,bcm7278-dpfe-cpu", .data = &dpfe_api_old_v2 },
+	{ .compatible = "brcm,bcm7211-dpfe-cpu", .data = &dpfe_api_new_v2 },
 	/* API v3 is the default going forward */
 	{ .compatible = "brcm,dpfe-cpu", .data = &dpfe_api_v3 },
 	{}
diff --git a/drivers/memory/emif.c b/drivers/memory/emif.c
index 402c6bc8e621..9d9127bf2a59 100644
--- a/drivers/memory/emif.c
+++ b/drivers/memory/emif.c
@@ -1613,7 +1613,7 @@ static void emif_shutdown(struct platform_device *pdev)
 static int get_emif_reg_values(struct emif_data *emif, u32 freq,
 		struct emif_regs *regs)
 {
-	u32				cs1_used, ip_rev, phy_type;
+	u32				ip_rev, phy_type;
 	u32				cl, type;
 	const struct lpddr2_timings	*timings;
 	const struct lpddr2_min_tck	*min_tck;
@@ -1621,7 +1621,6 @@ static int get_emif_reg_values(struct emif_data *emif, u32 freq,
 	const struct lpddr2_addressing	*addressing;
 	struct emif_data		*emif_for_calc;
 	struct device			*dev;
-	const struct emif_custom_configs *custom_configs;
 
 	dev = emif->dev;
 	/*
@@ -1639,12 +1638,10 @@ static int get_emif_reg_values(struct emif_data *emif, u32 freq,
 
 	device_info	= emif_for_calc->plat_data->device_info;
 	type		= device_info->type;
-	cs1_used	= device_info->cs1_used;
 	ip_rev		= emif_for_calc->plat_data->ip_rev;
 	phy_type	= emif_for_calc->plat_data->phy_type;
 
 	min_tck		= emif_for_calc->plat_data->min_tck;
-	custom_configs	= emif_for_calc->plat_data->custom_configs;
 
 	set_ddr_clk_period(freq);
 
diff --git a/drivers/memory/jedec_ddr.h b/drivers/memory/jedec_ddr.h
index 4a21b5044ff8..e59ccbd982d0 100644
--- a/drivers/memory/jedec_ddr.h
+++ b/drivers/memory/jedec_ddr.h
@@ -29,6 +29,7 @@
 #define DDR_TYPE_LPDDR2_S4	3
 #define DDR_TYPE_LPDDR2_S2	4
 #define DDR_TYPE_LPDDR2_NVM	5
+#define DDR_TYPE_LPDDR3		6
 
 /* DDR IO width */
 #define DDR_IO_WIDTH_4		1
@@ -169,4 +170,64 @@ extern const struct lpddr2_timings
 	lpddr2_jedec_timings[NUM_DDR_TIMING_TABLE_ENTRIES];
 extern const struct lpddr2_min_tck lpddr2_jedec_min_tck;
 
+/*
+ * Structure for timings for LPDDR3 based on LPDDR2 plus additional fields.
+ * All parameters are in pico seconds(ps) excluding max_freq, min_freq which
+ * are in Hz.
+ */
+struct lpddr3_timings {
+	u32 max_freq;
+	u32 min_freq;
+	u32 tRFC;
+	u32 tRRD;
+	u32 tRPab;
+	u32 tRPpb;
+	u32 tRCD;
+	u32 tRC;
+	u32 tRAS;
+	u32 tWTR;
+	u32 tWR;
+	u32 tRTP;
+	u32 tW2W_C2C;
+	u32 tR2R_C2C;
+	u32 tWL;
+	u32 tDQSCK;
+	u32 tRL;
+	u32 tFAW;
+	u32 tXSR;
+	u32 tXP;
+	u32 tCKE;
+	u32 tCKESR;
+	u32 tMRD;
+};
+
+/*
+ * Min value for some parameters in terms of number of tCK cycles(nCK)
+ * Please set to zero parameters that are not valid for a given memory
+ * type
+ */
+struct lpddr3_min_tck {
+	u32 tRFC;
+	u32 tRRD;
+	u32 tRPab;
+	u32 tRPpb;
+	u32 tRCD;
+	u32 tRC;
+	u32 tRAS;
+	u32 tWTR;
+	u32 tWR;
+	u32 tRTP;
+	u32 tW2W_C2C;
+	u32 tR2R_C2C;
+	u32 tWL;
+	u32 tDQSCK;
+	u32 tRL;
+	u32 tFAW;
+	u32 tXSR;
+	u32 tXP;
+	u32 tCKE;
+	u32 tCKESR;
+	u32 tMRD;
+};
+
 #endif /* __JEDEC_DDR_H */
diff --git a/drivers/memory/of_memory.c b/drivers/memory/of_memory.c
index 46539b27a3fb..71f26eac7350 100644
--- a/drivers/memory/of_memory.c
+++ b/drivers/memory/of_memory.c
@@ -3,6 +3,7 @@
  * OpenFirmware helpers for memory drivers
  *
  * Copyright (C) 2012 Texas Instruments, Inc.
+ * Copyright (C) 2019 Samsung Electronics Co., Ltd.
  */
 
 #include <linux/device.h>
@@ -149,3 +150,151 @@ default_timings:
 	return lpddr2_jedec_timings;
 }
 EXPORT_SYMBOL(of_get_ddr_timings);
+
+/**
+ * of_lpddr3_get_min_tck() - extract min timing values for lpddr3
+ * @np: pointer to ddr device tree node
+ * @device: device requesting for min timing values
+ *
+ * Populates the lpddr3_min_tck structure by extracting data
+ * from device tree node. Returns a pointer to the populated
+ * structure. If any error in populating the structure, returns NULL.
+ */
+const struct lpddr3_min_tck *of_lpddr3_get_min_tck(struct device_node *np,
+						   struct device *dev)
+{
+	int			ret = 0;
+	struct lpddr3_min_tck	*min;
+
+	min = devm_kzalloc(dev, sizeof(*min), GFP_KERNEL);
+	if (!min)
+		goto default_min_tck;
+
+	ret |= of_property_read_u32(np, "tRFC-min-tck", &min->tRFC);
+	ret |= of_property_read_u32(np, "tRRD-min-tck", &min->tRRD);
+	ret |= of_property_read_u32(np, "tRPab-min-tck", &min->tRPab);
+	ret |= of_property_read_u32(np, "tRPpb-min-tck", &min->tRPpb);
+	ret |= of_property_read_u32(np, "tRCD-min-tck", &min->tRCD);
+	ret |= of_property_read_u32(np, "tRC-min-tck", &min->tRC);
+	ret |= of_property_read_u32(np, "tRAS-min-tck", &min->tRAS);
+	ret |= of_property_read_u32(np, "tWTR-min-tck", &min->tWTR);
+	ret |= of_property_read_u32(np, "tWR-min-tck", &min->tWR);
+	ret |= of_property_read_u32(np, "tRTP-min-tck", &min->tRTP);
+	ret |= of_property_read_u32(np, "tW2W-C2C-min-tck", &min->tW2W_C2C);
+	ret |= of_property_read_u32(np, "tR2R-C2C-min-tck", &min->tR2R_C2C);
+	ret |= of_property_read_u32(np, "tWL-min-tck", &min->tWL);
+	ret |= of_property_read_u32(np, "tDQSCK-min-tck", &min->tDQSCK);
+	ret |= of_property_read_u32(np, "tRL-min-tck", &min->tRL);
+	ret |= of_property_read_u32(np, "tFAW-min-tck", &min->tFAW);
+	ret |= of_property_read_u32(np, "tXSR-min-tck", &min->tXSR);
+	ret |= of_property_read_u32(np, "tXP-min-tck", &min->tXP);
+	ret |= of_property_read_u32(np, "tCKE-min-tck", &min->tCKE);
+	ret |= of_property_read_u32(np, "tCKESR-min-tck", &min->tCKESR);
+	ret |= of_property_read_u32(np, "tMRD-min-tck", &min->tMRD);
+
+	if (ret) {
+		dev_warn(dev, "%s: errors while parsing min-tck values\n",
+			 __func__);
+		devm_kfree(dev, min);
+		goto default_min_tck;
+	}
+
+	return min;
+
+default_min_tck:
+	dev_warn(dev, "%s: using default min-tck values\n", __func__);
+	return NULL;
+}
+EXPORT_SYMBOL(of_lpddr3_get_min_tck);
+
+static int of_lpddr3_do_get_timings(struct device_node *np,
+				    struct lpddr3_timings *tim)
+{
+	int ret;
+
+	/* The 'reg' param required since DT has changed, used as 'max-freq' */
+	ret = of_property_read_u32(np, "reg", &tim->max_freq);
+	ret |= of_property_read_u32(np, "min-freq", &tim->min_freq);
+	ret |= of_property_read_u32(np, "tRFC", &tim->tRFC);
+	ret |= of_property_read_u32(np, "tRRD", &tim->tRRD);
+	ret |= of_property_read_u32(np, "tRPab", &tim->tRPab);
+	ret |= of_property_read_u32(np, "tRPpb", &tim->tRPpb);
+	ret |= of_property_read_u32(np, "tRCD", &tim->tRCD);
+	ret |= of_property_read_u32(np, "tRC", &tim->tRC);
+	ret |= of_property_read_u32(np, "tRAS", &tim->tRAS);
+	ret |= of_property_read_u32(np, "tWTR", &tim->tWTR);
+	ret |= of_property_read_u32(np, "tWR", &tim->tWR);
+	ret |= of_property_read_u32(np, "tRTP", &tim->tRTP);
+	ret |= of_property_read_u32(np, "tW2W-C2C", &tim->tW2W_C2C);
+	ret |= of_property_read_u32(np, "tR2R-C2C", &tim->tR2R_C2C);
+	ret |= of_property_read_u32(np, "tFAW", &tim->tFAW);
+	ret |= of_property_read_u32(np, "tXSR", &tim->tXSR);
+	ret |= of_property_read_u32(np, "tXP", &tim->tXP);
+	ret |= of_property_read_u32(np, "tCKE", &tim->tCKE);
+	ret |= of_property_read_u32(np, "tCKESR", &tim->tCKESR);
+	ret |= of_property_read_u32(np, "tMRD", &tim->tMRD);
+
+	return ret;
+}
+
+/**
+ * of_lpddr3_get_ddr_timings() - extracts the lpddr3 timings and updates no of
+ * frequencies available.
+ * @np_ddr: Pointer to ddr device tree node
+ * @dev: Device requesting for ddr timings
+ * @device_type: Type of ddr
+ * @nr_frequencies: No of frequencies available for ddr
+ * (updated by this function)
+ *
+ * Populates lpddr3_timings structure by extracting data from device
+ * tree node. Returns pointer to populated structure. If any error
+ * while populating, returns NULL.
+ */
+const struct lpddr3_timings
+*of_lpddr3_get_ddr_timings(struct device_node *np_ddr, struct device *dev,
+			   u32 device_type, u32 *nr_frequencies)
+{
+	struct lpddr3_timings	*timings = NULL;
+	u32			arr_sz = 0, i = 0;
+	struct device_node	*np_tim;
+	char			*tim_compat = NULL;
+
+	switch (device_type) {
+	case DDR_TYPE_LPDDR3:
+		tim_compat = "jedec,lpddr3-timings";
+		break;
+	default:
+		dev_warn(dev, "%s: un-supported memory type\n", __func__);
+	}
+
+	for_each_child_of_node(np_ddr, np_tim)
+		if (of_device_is_compatible(np_tim, tim_compat))
+			arr_sz++;
+
+	if (arr_sz)
+		timings = devm_kcalloc(dev, arr_sz, sizeof(*timings),
+				       GFP_KERNEL);
+
+	if (!timings)
+		goto default_timings;
+
+	for_each_child_of_node(np_ddr, np_tim) {
+		if (of_device_is_compatible(np_tim, tim_compat)) {
+			if (of_lpddr3_do_get_timings(np_tim, &timings[i])) {
+				devm_kfree(dev, timings);
+				goto default_timings;
+			}
+			i++;
+		}
+	}
+
+	*nr_frequencies = arr_sz;
+
+	return timings;
+
+default_timings:
+	dev_warn(dev, "%s: failed to get timings\n", __func__);
+	*nr_frequencies = 0;
+	return NULL;
+}
+EXPORT_SYMBOL(of_lpddr3_get_ddr_timings);
diff --git a/drivers/memory/of_memory.h b/drivers/memory/of_memory.h
index b077cc836b0b..e39ecc4c733d 100644
--- a/drivers/memory/of_memory.h
+++ b/drivers/memory/of_memory.h
@@ -14,6 +14,11 @@ extern const struct lpddr2_min_tck *of_get_min_tck(struct device_node *np,
 extern const struct lpddr2_timings
 	*of_get_ddr_timings(struct device_node *np_ddr, struct device *dev,
 	u32 device_type, u32 *nr_frequencies);
+extern const struct lpddr3_min_tck
+	*of_lpddr3_get_min_tck(struct device_node *np, struct device *dev);
+extern const struct lpddr3_timings
+	*of_lpddr3_get_ddr_timings(struct device_node *np_ddr,
+	struct device *dev, u32 device_type, u32 *nr_frequencies);
 #else
 static inline const struct lpddr2_min_tck
 	*of_get_min_tck(struct device_node *np, struct device *dev)
@@ -27,6 +32,19 @@ static inline const struct lpddr2_timings
 {
 	return NULL;
 }
+
+static inline const struct lpddr3_min_tck
+	*of_lpddr3_get_min_tck(struct device_node *np, struct device *dev)
+{
+	return NULL;
+}
+
+static inline const struct lpddr3_timings
+	*of_lpddr3_get_ddr_timings(struct device_node *np_ddr,
+	struct device *dev, u32 device_type, u32 *nr_frequencies)
+{
+	return NULL;
+}
 #endif /* CONFIG_OF && CONFIG_DDR */
 
 #endif /* __LINUX_MEMORY_OF_REG_ */
diff --git a/drivers/memory/samsung/Kconfig b/drivers/memory/samsung/Kconfig
index 79ce7ea58903..e9c3ce92350c 100644
--- a/drivers/memory/samsung/Kconfig
+++ b/drivers/memory/samsung/Kconfig
@@ -7,6 +7,19 @@ config SAMSUNG_MC
 
 if SAMSUNG_MC
 
+config EXYNOS5422_DMC
+	tristate "EXYNOS5422 Dynamic Memory Controller driver"
+	depends on ARCH_EXYNOS || (COMPILE_TEST && HAS_IOMEM)
+	select DDR
+	depends on DEVFREQ_GOV_SIMPLE_ONDEMAND
+	depends on (PM_DEVFREQ && PM_DEVFREQ_EVENT)
+	help
+	  This adds driver for Exynos5422 DMC (Dynamic Memory Controller).
+	  The driver provides support for Dynamic Voltage and Frequency Scaling in
+	  DMC and DRAM. It also supports changing timings of DRAM running with
+	  different frequency. The timings are calculated based on DT memory
+	  information.
+
 config EXYNOS_SROM
 	bool "Exynos SROM controller driver" if COMPILE_TEST
 	depends on (ARM && ARCH_EXYNOS) || (COMPILE_TEST && HAS_IOMEM)
diff --git a/drivers/memory/samsung/Makefile b/drivers/memory/samsung/Makefile
index 00587be66211..ea071be21c44 100644
--- a/drivers/memory/samsung/Makefile
+++ b/drivers/memory/samsung/Makefile
@@ -1,2 +1,3 @@
 # SPDX-License-Identifier: GPL-2.0
+obj-$(CONFIG_EXYNOS5422_DMC)	+= exynos5422-dmc.o
 obj-$(CONFIG_EXYNOS_SROM)	+= exynos-srom.o
diff --git a/drivers/memory/samsung/exynos5422-dmc.c b/drivers/memory/samsung/exynos5422-dmc.c
new file mode 100644
index 000000000000..47dbf6d1789f
--- /dev/null
+++ b/drivers/memory/samsung/exynos5422-dmc.c
@@ -0,0 +1,1550 @@
+// SPDX-License-Identifier: GPL-2.0
+/*
+ * Copyright (c) 2019 Samsung Electronics Co., Ltd.
+ * Author: Lukasz Luba <l.luba@partner.samsung.com>
+ */
+
+#include <linux/clk.h>
+#include <linux/devfreq.h>
+#include <linux/devfreq-event.h>
+#include <linux/device.h>
+#include <linux/interrupt.h>
+#include <linux/io.h>
+#include <linux/mfd/syscon.h>
+#include <linux/module.h>
+#include <linux/of_device.h>
+#include <linux/pm_opp.h>
+#include <linux/platform_device.h>
+#include <linux/regmap.h>
+#include <linux/regulator/consumer.h>
+#include <linux/slab.h>
+#include "../jedec_ddr.h"
+#include "../of_memory.h"
+
+#define EXYNOS5_DREXI_TIMINGAREF		(0x0030)
+#define EXYNOS5_DREXI_TIMINGROW0		(0x0034)
+#define EXYNOS5_DREXI_TIMINGDATA0		(0x0038)
+#define EXYNOS5_DREXI_TIMINGPOWER0		(0x003C)
+#define EXYNOS5_DREXI_TIMINGROW1		(0x00E4)
+#define EXYNOS5_DREXI_TIMINGDATA1		(0x00E8)
+#define EXYNOS5_DREXI_TIMINGPOWER1		(0x00EC)
+#define CDREX_PAUSE				(0x2091c)
+#define CDREX_LPDDR3PHY_CON3			(0x20a20)
+#define CDREX_LPDDR3PHY_CLKM_SRC		(0x20700)
+#define EXYNOS5_TIMING_SET_SWI			BIT(28)
+#define USE_MX_MSPLL_TIMINGS			(1)
+#define USE_BPLL_TIMINGS			(0)
+#define EXYNOS5_AREF_NORMAL			(0x2e)
+
+#define DREX_PPCCLKCON		(0x0130)
+#define DREX_PEREV2CONFIG	(0x013c)
+#define DREX_PMNC_PPC		(0xE000)
+#define DREX_CNTENS_PPC		(0xE010)
+#define DREX_CNTENC_PPC		(0xE020)
+#define DREX_INTENS_PPC		(0xE030)
+#define DREX_INTENC_PPC		(0xE040)
+#define DREX_FLAG_PPC		(0xE050)
+#define DREX_PMCNT2_PPC		(0xE130)
+
+/*
+ * A value for register DREX_PMNC_PPC which should be written to reset
+ * the cycle counter CCNT (a reference wall clock). It sets zero to the
+ * CCNT counter.
+ */
+#define CC_RESET		BIT(2)
+
+/*
+ * A value for register DREX_PMNC_PPC which does the reset of all performance
+ * counters to zero.
+ */
+#define PPC_COUNTER_RESET	BIT(1)
+
+/*
+ * Enables all configured counters (including cycle counter). The value should
+ * be written to the register DREX_PMNC_PPC.
+ */
+#define PPC_ENABLE		BIT(0)
+
+/* A value for register DREX_PPCCLKCON which enables performance events clock.
+ * Must be written before first access to the performance counters register
+ * set, otherwise it could crash.
+ */
+#define PEREV_CLK_EN		BIT(0)
+
+/*
+ * Values which are used to enable counters, interrupts or configure flags of
+ * the performance counters. They configure counter 2 and cycle counter.
+ */
+#define PERF_CNT2		BIT(2)
+#define PERF_CCNT		BIT(31)
+
+/*
+ * Performance event types which are used for setting the preferred event
+ * to track in the counters.
+ * There is a set of different types, the values are from range 0 to 0x6f.
+ * These settings should be written to the configuration register which manages
+ * the type of the event (register DREX_PEREV2CONFIG).
+ */
+#define READ_TRANSFER_CH0	(0x6d)
+#define READ_TRANSFER_CH1	(0x6f)
+
+#define PERF_COUNTER_START_VALUE 0xff000000
+#define PERF_EVENT_UP_DOWN_THRESHOLD 900000000ULL
+
+/**
+ * struct dmc_opp_table - Operating level desciption
+ *
+ * Covers frequency and voltage settings of the DMC operating mode.
+ */
+struct dmc_opp_table {
+	u32 freq_hz;
+	u32 volt_uv;
+};
+
+/**
+ * struct exynos5_dmc - main structure describing DMC device
+ *
+ * The main structure for the Dynamic Memory Controller which covers clocks,
+ * memory regions, HW information, parameters and current operating mode.
+ */
+struct exynos5_dmc {
+	struct device *dev;
+	struct devfreq *df;
+	struct devfreq_simple_ondemand_data gov_data;
+	void __iomem *base_drexi0;
+	void __iomem *base_drexi1;
+	struct regmap *clk_regmap;
+	struct mutex lock;
+	unsigned long curr_rate;
+	unsigned long curr_volt;
+	unsigned long bypass_rate;
+	struct dmc_opp_table *opp;
+	struct dmc_opp_table opp_bypass;
+	int opp_count;
+	u32 timings_arr_size;
+	u32 *timing_row;
+	u32 *timing_data;
+	u32 *timing_power;
+	const struct lpddr3_timings *timings;
+	const struct lpddr3_min_tck *min_tck;
+	u32 bypass_timing_row;
+	u32 bypass_timing_data;
+	u32 bypass_timing_power;
+	struct regulator *vdd_mif;
+	struct clk *fout_spll;
+	struct clk *fout_bpll;
+	struct clk *mout_spll;
+	struct clk *mout_bpll;
+	struct clk *mout_mclk_cdrex;
+	struct clk *mout_mx_mspll_ccore;
+	struct clk *mx_mspll_ccore_phy;
+	struct clk *mout_mx_mspll_ccore_phy;
+	struct devfreq_event_dev **counter;
+	int num_counters;
+	u64 last_overflow_ts[2];
+	unsigned long load;
+	unsigned long total;
+	bool in_irq_mode;
+};
+
+#define TIMING_FIELD(t_name, t_bit_beg, t_bit_end) \
+	{ .name = t_name, .bit_beg = t_bit_beg, .bit_end = t_bit_end }
+
+#define TIMING_VAL2REG(timing, t_val)			\
+({							\
+		u32 __val;				\
+		__val = (t_val) << (timing)->bit_beg;	\
+		__val;					\
+})
+
+struct timing_reg {
+	char *name;
+	int bit_beg;
+	int bit_end;
+	unsigned int val;
+};
+
+static const struct timing_reg timing_row[] = {
+	TIMING_FIELD("tRFC", 24, 31),
+	TIMING_FIELD("tRRD", 20, 23),
+	TIMING_FIELD("tRP", 16, 19),
+	TIMING_FIELD("tRCD", 12, 15),
+	TIMING_FIELD("tRC", 6, 11),
+	TIMING_FIELD("tRAS", 0, 5),
+};
+
+static const struct timing_reg timing_data[] = {
+	TIMING_FIELD("tWTR", 28, 31),
+	TIMING_FIELD("tWR", 24, 27),
+	TIMING_FIELD("tRTP", 20, 23),
+	TIMING_FIELD("tW2W-C2C", 14, 14),
+	TIMING_FIELD("tR2R-C2C", 12, 12),
+	TIMING_FIELD("WL", 8, 11),
+	TIMING_FIELD("tDQSCK", 4, 7),
+	TIMING_FIELD("RL", 0, 3),
+};
+
+static const struct timing_reg timing_power[] = {
+	TIMING_FIELD("tFAW", 26, 31),
+	TIMING_FIELD("tXSR", 16, 25),
+	TIMING_FIELD("tXP", 8, 15),
+	TIMING_FIELD("tCKE", 4, 7),
+	TIMING_FIELD("tMRD", 0, 3),
+};
+
+#define TIMING_COUNT (ARRAY_SIZE(timing_row) + ARRAY_SIZE(timing_data) + \
+		      ARRAY_SIZE(timing_power))
+
+static int exynos5_counters_set_event(struct exynos5_dmc *dmc)
+{
+	int i, ret;
+
+	for (i = 0; i < dmc->num_counters; i++) {
+		if (!dmc->counter[i])
+			continue;
+		ret = devfreq_event_set_event(dmc->counter[i]);
+		if (ret < 0)
+			return ret;
+	}
+	return 0;
+}
+
+static int exynos5_counters_enable_edev(struct exynos5_dmc *dmc)
+{
+	int i, ret;
+
+	for (i = 0; i < dmc->num_counters; i++) {
+		if (!dmc->counter[i])
+			continue;
+		ret = devfreq_event_enable_edev(dmc->counter[i]);
+		if (ret < 0)
+			return ret;
+	}
+	return 0;
+}
+
+static int exynos5_counters_disable_edev(struct exynos5_dmc *dmc)
+{
+	int i, ret;
+
+	for (i = 0; i < dmc->num_counters; i++) {
+		if (!dmc->counter[i])
+			continue;
+		ret = devfreq_event_disable_edev(dmc->counter[i]);
+		if (ret < 0)
+			return ret;
+	}
+	return 0;
+}
+
+/**
+ * find_target_freq_id() - Finds requested frequency in local DMC configuration
+ * @dmc:	device for which the information is checked
+ * @target_rate:	requested frequency in KHz
+ *
+ * Seeks in the local DMC driver structure for the requested frequency value
+ * and returns index or error value.
+ */
+static int find_target_freq_idx(struct exynos5_dmc *dmc,
+				unsigned long target_rate)
+{
+	int i;
+
+	for (i = dmc->opp_count - 1; i >= 0; i--)
+		if (dmc->opp[i].freq_hz <= target_rate)
+			return i;
+
+	return -EINVAL;
+}
+
+/**
+ * exynos5_switch_timing_regs() - Changes bank register set for DRAM timings
+ * @dmc:	device for which the new settings is going to be applied
+ * @set:	boolean variable passing set value
+ *
+ * Changes the register set, which holds timing parameters.
+ * There is two register sets: 0 and 1. The register set 0
+ * is used in normal operation when the clock is provided from main PLL.
+ * The bank register set 1 is used when the main PLL frequency is going to be
+ * changed and the clock is taken from alternative, stable source.
+ * This function switches between these banks according to the
+ * currently used clock source.
+ */
+static void exynos5_switch_timing_regs(struct exynos5_dmc *dmc, bool set)
+{
+	unsigned int reg;
+	int ret;
+
+	ret = regmap_read(dmc->clk_regmap, CDREX_LPDDR3PHY_CON3, &reg);
+
+	if (set)
+		reg |= EXYNOS5_TIMING_SET_SWI;
+	else
+		reg &= ~EXYNOS5_TIMING_SET_SWI;
+
+	regmap_write(dmc->clk_regmap, CDREX_LPDDR3PHY_CON3, reg);
+}
+
+/**
+ * exynos5_init_freq_table() - Initialized PM OPP framework
+ * @dmc:	DMC device for which the frequencies are used for OPP init
+ * @profile:	devfreq device's profile
+ *
+ * Populate the devfreq device's OPP table based on current frequency, voltage.
+ */
+static int exynos5_init_freq_table(struct exynos5_dmc *dmc,
+				   struct devfreq_dev_profile *profile)
+{
+	int i, ret;
+	int idx;
+	unsigned long freq;
+
+	ret = dev_pm_opp_of_add_table(dmc->dev);
+	if (ret < 0) {
+		dev_err(dmc->dev, "Failed to get OPP table\n");
+		return ret;
+	}
+
+	dmc->opp_count = dev_pm_opp_get_opp_count(dmc->dev);
+
+	dmc->opp = devm_kmalloc_array(dmc->dev, dmc->opp_count,
+				      sizeof(struct dmc_opp_table), GFP_KERNEL);
+	if (!dmc->opp)
+		goto err_opp;
+
+	idx = dmc->opp_count - 1;
+	for (i = 0, freq = ULONG_MAX; i < dmc->opp_count; i++, freq--) {
+		struct dev_pm_opp *opp;
+
+		opp = dev_pm_opp_find_freq_floor(dmc->dev, &freq);
+		if (IS_ERR(opp))
+			goto err_opp;
+
+		dmc->opp[idx - i].freq_hz = freq;
+		dmc->opp[idx - i].volt_uv = dev_pm_opp_get_voltage(opp);
+
+		dev_pm_opp_put(opp);
+	}
+
+	return 0;
+
+err_opp:
+	dev_pm_opp_of_remove_table(dmc->dev);
+
+	return -EINVAL;
+}
+
+/**
+ * exynos5_set_bypass_dram_timings() - Low-level changes of the DRAM timings
+ * @dmc:	device for which the new settings is going to be applied
+ * @param:	DRAM parameters which passes timing data
+ *
+ * Low-level function for changing timings for DRAM memory clocking from
+ * 'bypass' clock source (fixed frequency @400MHz).
+ * It uses timing bank registers set 1.
+ */
+static void exynos5_set_bypass_dram_timings(struct exynos5_dmc *dmc)
+{
+	writel(EXYNOS5_AREF_NORMAL,
+	       dmc->base_drexi0 + EXYNOS5_DREXI_TIMINGAREF);
+
+	writel(dmc->bypass_timing_row,
+	       dmc->base_drexi0 + EXYNOS5_DREXI_TIMINGROW1);
+	writel(dmc->bypass_timing_row,
+	       dmc->base_drexi1 + EXYNOS5_DREXI_TIMINGROW1);
+	writel(dmc->bypass_timing_data,
+	       dmc->base_drexi0 + EXYNOS5_DREXI_TIMINGDATA1);
+	writel(dmc->bypass_timing_data,
+	       dmc->base_drexi1 + EXYNOS5_DREXI_TIMINGDATA1);
+	writel(dmc->bypass_timing_power,
+	       dmc->base_drexi0 + EXYNOS5_DREXI_TIMINGPOWER1);
+	writel(dmc->bypass_timing_power,
+	       dmc->base_drexi1 + EXYNOS5_DREXI_TIMINGPOWER1);
+}
+
+/**
+ * exynos5_dram_change_timings() - Low-level changes of the DRAM final timings
+ * @dmc:	device for which the new settings is going to be applied
+ * @target_rate:	target frequency of the DMC
+ *
+ * Low-level function for changing timings for DRAM memory operating from main
+ * clock source (BPLL), which can have different frequencies. Thus, each
+ * frequency must have corresponding timings register values in order to keep
+ * the needed delays.
+ * It uses timing bank registers set 0.
+ */
+static int exynos5_dram_change_timings(struct exynos5_dmc *dmc,
+				       unsigned long target_rate)
+{
+	int idx;
+
+	for (idx = dmc->opp_count - 1; idx >= 0; idx--)
+		if (dmc->opp[idx].freq_hz <= target_rate)
+			break;
+
+	if (idx < 0)
+		return -EINVAL;
+
+	writel(EXYNOS5_AREF_NORMAL,
+	       dmc->base_drexi0 + EXYNOS5_DREXI_TIMINGAREF);
+
+	writel(dmc->timing_row[idx],
+	       dmc->base_drexi0 + EXYNOS5_DREXI_TIMINGROW0);
+	writel(dmc->timing_row[idx],
+	       dmc->base_drexi1 + EXYNOS5_DREXI_TIMINGROW0);
+	writel(dmc->timing_data[idx],
+	       dmc->base_drexi0 + EXYNOS5_DREXI_TIMINGDATA0);
+	writel(dmc->timing_data[idx],
+	       dmc->base_drexi1 + EXYNOS5_DREXI_TIMINGDATA0);
+	writel(dmc->timing_power[idx],
+	       dmc->base_drexi0 + EXYNOS5_DREXI_TIMINGPOWER0);
+	writel(dmc->timing_power[idx],
+	       dmc->base_drexi1 + EXYNOS5_DREXI_TIMINGPOWER0);
+
+	return 0;
+}
+
+/**
+ * exynos5_dmc_align_target_voltage() - Sets the final voltage for the DMC
+ * @dmc:	device for which it is going to be set
+ * @target_volt:	new voltage which is chosen to be final
+ *
+ * Function tries to align voltage to the safe level for 'normal' mode.
+ * It checks the need of higher voltage and changes the value. The target
+ * voltage might be lower that currently set and still the system will be
+ * stable.
+ */
+static int exynos5_dmc_align_target_voltage(struct exynos5_dmc *dmc,
+					    unsigned long target_volt)
+{
+	int ret = 0;
+
+	if (dmc->curr_volt <= target_volt)
+		return 0;
+
+	ret = regulator_set_voltage(dmc->vdd_mif, target_volt,
+				    target_volt);
+	if (!ret)
+		dmc->curr_volt = target_volt;
+
+	return ret;
+}
+
+/**
+ * exynos5_dmc_align_bypass_voltage() - Sets the voltage for the DMC
+ * @dmc:	device for which it is going to be set
+ * @target_volt:	new voltage which is chosen to be final
+ *
+ * Function tries to align voltage to the safe level for the 'bypass' mode.
+ * It checks the need of higher voltage and changes the value.
+ * The target voltage must not be less than currently needed, because
+ * for current frequency the device might become unstable.
+ */
+static int exynos5_dmc_align_bypass_voltage(struct exynos5_dmc *dmc,
+					    unsigned long target_volt)
+{
+	int ret = 0;
+	unsigned long bypass_volt = dmc->opp_bypass.volt_uv;
+
+	target_volt = max(bypass_volt, target_volt);
+
+	if (dmc->curr_volt >= target_volt)
+		return 0;
+
+	ret = regulator_set_voltage(dmc->vdd_mif, target_volt,
+				    target_volt);
+	if (!ret)
+		dmc->curr_volt = target_volt;
+
+	return ret;
+}
+
+/**
+ * exynos5_dmc_align_bypass_dram_timings() - Chooses and sets DRAM timings
+ * @dmc:	device for which it is going to be set
+ * @target_rate:	new frequency which is chosen to be final
+ *
+ * Function changes the DRAM timings for the temporary 'bypass' mode.
+ */
+static int exynos5_dmc_align_bypass_dram_timings(struct exynos5_dmc *dmc,
+						 unsigned long target_rate)
+{
+	int idx = find_target_freq_idx(dmc, target_rate);
+
+	if (idx < 0)
+		return -EINVAL;
+
+	exynos5_set_bypass_dram_timings(dmc);
+
+	return 0;
+}
+
+/**
+ * exynos5_dmc_switch_to_bypass_configuration() - Switching to temporary clock
+ * @dmc:	DMC device for which the switching is going to happen
+ * @target_rate:	new frequency which is going to be set as a final
+ * @target_volt:	new voltage which is going to be set as a final
+ *
+ * Function configures DMC and clocks for operating in temporary 'bypass' mode.
+ * This mode is used only temporary but if required, changes voltage and timings
+ * for DRAM chips. It switches the main clock to stable clock source for the
+ * period of the main PLL reconfiguration.
+ */
+static int
+exynos5_dmc_switch_to_bypass_configuration(struct exynos5_dmc *dmc,
+					   unsigned long target_rate,
+					   unsigned long target_volt)
+{
+	int ret;
+
+	/*
+	 * Having higher voltage for a particular frequency does not harm
+	 * the chip. Use it for the temporary frequency change when one
+	 * voltage manipulation might be avoided.
+	 */
+	ret = exynos5_dmc_align_bypass_voltage(dmc, target_volt);
+	if (ret)
+		return ret;
+
+	/*
+	 * Longer delays for DRAM does not cause crash, the opposite does.
+	 */
+	ret = exynos5_dmc_align_bypass_dram_timings(dmc, target_rate);
+	if (ret)
+		return ret;
+
+	/*
+	 * Delays are long enough, so use them for the new coming clock.
+	 */
+	exynos5_switch_timing_regs(dmc, USE_MX_MSPLL_TIMINGS);
+
+	return ret;
+}
+
+/**
+ * exynos5_dmc_change_freq_and_volt() - Changes voltage and frequency of the DMC
+ * using safe procedure
+ * @dmc:	device for which the frequency is going to be changed
+ * @target_rate:	requested new frequency
+ * @target_volt:	requested voltage which corresponds to the new frequency
+ *
+ * The DMC frequency change procedure requires a few steps.
+ * The main requirement is to change the clock source in the clk mux
+ * for the time of main clock PLL locking. The assumption is that the
+ * alternative clock source set as parent is stable.
+ * The second parent's clock frequency is fixed to 400MHz, it is named 'bypass'
+ * clock. This requires alignment in DRAM timing parameters for the new
+ * T-period. There is two bank sets for keeping DRAM
+ * timings: set 0 and set 1. The set 0 is used when main clock source is
+ * chosen. The 2nd set of regs is used for 'bypass' clock. Switching between
+ * the two bank sets is part of the process.
+ * The voltage must also be aligned to the minimum required level. There is
+ * this intermediate step with switching to 'bypass' parent clock source.
+ * if the old voltage is lower, it requires an increase of the voltage level.
+ * The complexity of the voltage manipulation is hidden in low level function.
+ * In this function there is last alignment of the voltage level at the end.
+ */
+static int
+exynos5_dmc_change_freq_and_volt(struct exynos5_dmc *dmc,
+				 unsigned long target_rate,
+				 unsigned long target_volt)
+{
+	int ret;
+
+	ret = exynos5_dmc_switch_to_bypass_configuration(dmc, target_rate,
+							 target_volt);
+	if (ret)
+		return ret;
+
+	/*
+	 * Voltage is set at least to a level needed for this frequency,
+	 * so switching clock source is safe now.
+	 */
+	clk_prepare_enable(dmc->fout_spll);
+	clk_prepare_enable(dmc->mout_spll);
+	clk_prepare_enable(dmc->mout_mx_mspll_ccore);
+
+	ret = clk_set_parent(dmc->mout_mclk_cdrex, dmc->mout_mx_mspll_ccore);
+	if (ret)
+		goto disable_clocks;
+
+	/*
+	 * We are safe to increase the timings for current bypass frequency.
+	 * Thanks to this the settings will be ready for the upcoming clock
+	 * source change.
+	 */
+	exynos5_dram_change_timings(dmc, target_rate);
+
+	clk_set_rate(dmc->fout_bpll, target_rate);
+
+	exynos5_switch_timing_regs(dmc, USE_BPLL_TIMINGS);
+
+	ret = clk_set_parent(dmc->mout_mclk_cdrex, dmc->mout_bpll);
+	if (ret)
+		goto disable_clocks;
+
+	/*
+	 * Make sure if the voltage is not from 'bypass' settings and align to
+	 * the right level for power efficiency.
+	 */
+	ret = exynos5_dmc_align_target_voltage(dmc, target_volt);
+
+disable_clocks:
+	clk_disable_unprepare(dmc->mout_mx_mspll_ccore);
+	clk_disable_unprepare(dmc->mout_spll);
+	clk_disable_unprepare(dmc->fout_spll);
+
+	return ret;
+}
+
+/**
+ * exynos5_dmc_get_volt_freq() - Gets the frequency and voltage from the OPP
+ * table.
+ * @dmc:	device for which the frequency is going to be changed
+ * @freq:       requested frequency in KHz
+ * @target_rate:	returned frequency which is the same or lower than
+ *			requested
+ * @target_volt:	returned voltage which corresponds to the returned
+ *			frequency
+ *
+ * Function gets requested frequency and checks OPP framework for needed
+ * frequency and voltage. It populates the values 'target_rate' and
+ * 'target_volt' or returns error value when OPP framework fails.
+ */
+static int exynos5_dmc_get_volt_freq(struct exynos5_dmc *dmc,
+				     unsigned long *freq,
+				     unsigned long *target_rate,
+				     unsigned long *target_volt, u32 flags)
+{
+	struct dev_pm_opp *opp;
+
+	opp = devfreq_recommended_opp(dmc->dev, freq, flags);
+	if (IS_ERR(opp))
+		return PTR_ERR(opp);
+
+	*target_rate = dev_pm_opp_get_freq(opp);
+	*target_volt = dev_pm_opp_get_voltage(opp);
+	dev_pm_opp_put(opp);
+
+	return 0;
+}
+
+/**
+ * exynos5_dmc_target() - Function responsible for changing frequency of DMC
+ * @dev:	device for which the frequency is going to be changed
+ * @freq:	requested frequency in KHz
+ * @flags:	flags provided for this frequency change request
+ *
+ * An entry function provided to the devfreq framework which provides frequency
+ * change of the DMC. The function gets the possible rate from OPP table based
+ * on requested frequency. It calls the next function responsible for the
+ * frequency and voltage change. In case of failure, does not set 'curr_rate'
+ * and returns error value to the framework.
+ */
+static int exynos5_dmc_target(struct device *dev, unsigned long *freq,
+			      u32 flags)
+{
+	struct exynos5_dmc *dmc = dev_get_drvdata(dev);
+	unsigned long target_rate = 0;
+	unsigned long target_volt = 0;
+	int ret;
+
+	ret = exynos5_dmc_get_volt_freq(dmc, freq, &target_rate, &target_volt,
+					flags);
+
+	if (ret)
+		return ret;
+
+	if (target_rate == dmc->curr_rate)
+		return 0;
+
+	mutex_lock(&dmc->lock);
+
+	ret = exynos5_dmc_change_freq_and_volt(dmc, target_rate, target_volt);
+
+	if (ret) {
+		mutex_unlock(&dmc->lock);
+		return ret;
+	}
+
+	dmc->curr_rate = target_rate;
+
+	mutex_unlock(&dmc->lock);
+	return 0;
+}
+
+/**
+ * exynos5_counters_get() - Gets the performance counters values.
+ * @dmc:	device for which the counters are going to be checked
+ * @load_count:	variable which is populated with counter value
+ * @total_count:	variable which is used as 'wall clock' reference
+ *
+ * Function which provides performance counters values. It sums up counters for
+ * two DMC channels. The 'total_count' is used as a reference and max value.
+ * The ratio 'load_count/total_count' shows the busy percentage [0%, 100%].
+ */
+static int exynos5_counters_get(struct exynos5_dmc *dmc,
+				unsigned long *load_count,
+				unsigned long *total_count)
+{
+	unsigned long total = 0;
+	struct devfreq_event_data event;
+	int ret, i;
+
+	*load_count = 0;
+
+	/* Take into account only read+write counters, but stop all */
+	for (i = 0; i < dmc->num_counters; i++) {
+		if (!dmc->counter[i])
+			continue;
+
+		ret = devfreq_event_get_event(dmc->counter[i], &event);
+		if (ret < 0)
+			return ret;
+
+		*load_count += event.load_count;
+
+		if (total < event.total_count)
+			total = event.total_count;
+	}
+
+	*total_count = total;
+
+	return 0;
+}
+
+/**
+ * exynos5_dmc_start_perf_events() - Setup and start performance event counters
+ * @dmc:	device for which the counters are going to be checked
+ * @beg_value:	initial value for the counter
+ *
+ * Function which enables needed counters, interrupts and sets initial values
+ * then starts the counters.
+ */
+static void exynos5_dmc_start_perf_events(struct exynos5_dmc *dmc,
+					  u32 beg_value)
+{
+	/* Enable interrupts for counter 2 */
+	writel(PERF_CNT2, dmc->base_drexi0 + DREX_INTENS_PPC);
+	writel(PERF_CNT2, dmc->base_drexi1 + DREX_INTENS_PPC);
+
+	/* Enable counter 2 and CCNT  */
+	writel(PERF_CNT2 | PERF_CCNT, dmc->base_drexi0 + DREX_CNTENS_PPC);
+	writel(PERF_CNT2 | PERF_CCNT, dmc->base_drexi1 + DREX_CNTENS_PPC);
+
+	/* Clear overflow flag for all counters */
+	writel(PERF_CNT2 | PERF_CCNT, dmc->base_drexi0 + DREX_FLAG_PPC);
+	writel(PERF_CNT2 | PERF_CCNT, dmc->base_drexi1 + DREX_FLAG_PPC);
+
+	/* Reset all counters */
+	writel(CC_RESET | PPC_COUNTER_RESET, dmc->base_drexi0 + DREX_PMNC_PPC);
+	writel(CC_RESET | PPC_COUNTER_RESET, dmc->base_drexi1 + DREX_PMNC_PPC);
+
+	/*
+	 * Set start value for the counters, the number of samples that
+	 * will be gathered is calculated as: 0xffffffff - beg_value
+	 */
+	writel(beg_value, dmc->base_drexi0 + DREX_PMCNT2_PPC);
+	writel(beg_value, dmc->base_drexi1 + DREX_PMCNT2_PPC);
+
+	/* Start all counters */
+	writel(PPC_ENABLE, dmc->base_drexi0 + DREX_PMNC_PPC);
+	writel(PPC_ENABLE, dmc->base_drexi1 + DREX_PMNC_PPC);
+}
+
+/**
+ * exynos5_dmc_perf_events_calc() - Calculate utilization
+ * @dmc:	device for which the counters are going to be checked
+ * @diff_ts:	time between last interrupt and current one
+ *
+ * Function which calculates needed utilization for the devfreq governor.
+ * It prepares values for 'busy_time' and 'total_time' based on elapsed time
+ * between interrupts, which approximates utilization.
+ */
+static void exynos5_dmc_perf_events_calc(struct exynos5_dmc *dmc, u64 diff_ts)
+{
+	/*
+	 * This is a simple algorithm for managing traffic on DMC.
+	 * When there is almost no load the counters overflow every 4s,
+	 * no mater the DMC frequency.
+	 * The high load might be approximated using linear function.
+	 * Knowing that, simple calculation can provide 'busy_time' and
+	 * 'total_time' to the devfreq governor which picks up target
+	 * frequency.
+	 * We want a fast ramp up and slow decay in frequency change function.
+	 */
+	if (diff_ts < PERF_EVENT_UP_DOWN_THRESHOLD) {
+		/*
+		 * Set higher utilization for the simple_ondemand governor.
+		 * The governor should increase the frequency of the DMC.
+		 */
+		dmc->load = 70;
+		dmc->total = 100;
+	} else {
+		/*
+		 * Set low utilization for the simple_ondemand governor.
+		 * The governor should decrease the frequency of the DMC.
+		 */
+		dmc->load = 35;
+		dmc->total = 100;
+	}
+
+	dev_dbg(dmc->dev, "diff_ts=%llu\n", diff_ts);
+}
+
+/**
+ * exynos5_dmc_perf_events_check() - Checks the status of the counters
+ * @dmc:	device for which the counters are going to be checked
+ *
+ * Function which is called from threaded IRQ to check the counters state
+ * and to call approximation for the needed utilization.
+ */
+static void exynos5_dmc_perf_events_check(struct exynos5_dmc *dmc)
+{
+	u32 val;
+	u64 diff_ts, ts;
+
+	ts = ktime_get_ns();
+
+	/* Stop all counters */
+	writel(0, dmc->base_drexi0 + DREX_PMNC_PPC);
+	writel(0, dmc->base_drexi1 + DREX_PMNC_PPC);
+
+	/* Check the source in interrupt flag registers (which channel) */
+	val = readl(dmc->base_drexi0 + DREX_FLAG_PPC);
+	if (val) {
+		diff_ts = ts - dmc->last_overflow_ts[0];
+		dmc->last_overflow_ts[0] = ts;
+		dev_dbg(dmc->dev, "drex0 0xE050 val= 0x%08x\n",  val);
+	} else {
+		val = readl(dmc->base_drexi1 + DREX_FLAG_PPC);
+		diff_ts = ts - dmc->last_overflow_ts[1];
+		dmc->last_overflow_ts[1] = ts;
+		dev_dbg(dmc->dev, "drex1 0xE050 val= 0x%08x\n",  val);
+	}
+
+	exynos5_dmc_perf_events_calc(dmc, diff_ts);
+
+	exynos5_dmc_start_perf_events(dmc, PERF_COUNTER_START_VALUE);
+}
+
+/**
+ * exynos5_dmc_enable_perf_events() - Enable performance events
+ * @dmc:	device for which the counters are going to be checked
+ *
+ * Function which is setup needed environment and enables counters.
+ */
+static void exynos5_dmc_enable_perf_events(struct exynos5_dmc *dmc)
+{
+	u64 ts;
+
+	/* Enable Performance Event Clock */
+	writel(PEREV_CLK_EN, dmc->base_drexi0 + DREX_PPCCLKCON);
+	writel(PEREV_CLK_EN, dmc->base_drexi1 + DREX_PPCCLKCON);
+
+	/* Select read transfers as performance event2 */
+	writel(READ_TRANSFER_CH0, dmc->base_drexi0 + DREX_PEREV2CONFIG);
+	writel(READ_TRANSFER_CH1, dmc->base_drexi1 + DREX_PEREV2CONFIG);
+
+	ts = ktime_get_ns();
+	dmc->last_overflow_ts[0] = ts;
+	dmc->last_overflow_ts[1] = ts;
+
+	/* Devfreq shouldn't be faster than initialization, play safe though. */
+	dmc->load = 99;
+	dmc->total = 100;
+}
+
+/**
+ * exynos5_dmc_disable_perf_events() - Disable performance events
+ * @dmc:	device for which the counters are going to be checked
+ *
+ * Function which stops, disables performance event counters and interrupts.
+ */
+static void exynos5_dmc_disable_perf_events(struct exynos5_dmc *dmc)
+{
+	/* Stop all counters */
+	writel(0, dmc->base_drexi0 + DREX_PMNC_PPC);
+	writel(0, dmc->base_drexi1 + DREX_PMNC_PPC);
+
+	/* Disable interrupts for counter 2 */
+	writel(PERF_CNT2, dmc->base_drexi0 + DREX_INTENC_PPC);
+	writel(PERF_CNT2, dmc->base_drexi1 + DREX_INTENC_PPC);
+
+	/* Disable counter 2 and CCNT  */
+	writel(PERF_CNT2 | PERF_CCNT, dmc->base_drexi0 + DREX_CNTENC_PPC);
+	writel(PERF_CNT2 | PERF_CCNT, dmc->base_drexi1 + DREX_CNTENC_PPC);
+
+	/* Clear overflow flag for all counters */
+	writel(PERF_CNT2 | PERF_CCNT, dmc->base_drexi0 + DREX_FLAG_PPC);
+	writel(PERF_CNT2 | PERF_CCNT, dmc->base_drexi1 + DREX_FLAG_PPC);
+}
+
+/**
+ * exynos5_dmc_get_status() - Read current DMC performance statistics.
+ * @dev:	device for which the statistics are requested
+ * @stat:	structure which has statistic fields
+ *
+ * Function reads the DMC performance counters and calculates 'busy_time'
+ * and 'total_time'. To protect from overflow, the values are shifted right
+ * by 10. After read out the counters are setup to count again.
+ */
+static int exynos5_dmc_get_status(struct device *dev,
+				  struct devfreq_dev_status *stat)
+{
+	struct exynos5_dmc *dmc = dev_get_drvdata(dev);
+	unsigned long load, total;
+	int ret;
+
+	if (dmc->in_irq_mode) {
+		stat->current_frequency = dmc->curr_rate;
+		stat->busy_time = dmc->load;
+		stat->total_time = dmc->total;
+	} else {
+		ret = exynos5_counters_get(dmc, &load, &total);
+		if (ret < 0)
+			return -EINVAL;
+
+		/* To protect from overflow, divide by 1024 */
+		stat->busy_time = load >> 10;
+		stat->total_time = total >> 10;
+
+		ret = exynos5_counters_set_event(dmc);
+		if (ret < 0) {
+			dev_err(dev, "could not set event counter\n");
+			return ret;
+		}
+	}
+
+	return 0;
+}
+
+/**
+ * exynos5_dmc_get_cur_freq() - Function returns current DMC frequency
+ * @dev:	device for which the framework checks operating frequency
+ * @freq:	returned frequency value
+ *
+ * It returns the currently used frequency of the DMC. The real operating
+ * frequency might be lower when the clock source value could not be divided
+ * to the requested value.
+ */
+static int exynos5_dmc_get_cur_freq(struct device *dev, unsigned long *freq)
+{
+	struct exynos5_dmc *dmc = dev_get_drvdata(dev);
+
+	mutex_lock(&dmc->lock);
+	*freq = dmc->curr_rate;
+	mutex_unlock(&dmc->lock);
+
+	return 0;
+}
+
+/**
+ * exynos5_dmc_df_profile - Devfreq governor's profile structure
+ *
+ * It provides to the devfreq framework needed functions and polling period.
+ */
+static struct devfreq_dev_profile exynos5_dmc_df_profile = {
+	.target = exynos5_dmc_target,
+	.get_dev_status = exynos5_dmc_get_status,
+	.get_cur_freq = exynos5_dmc_get_cur_freq,
+};
+
+/**
+ * exynos5_dmc_align_initial_frequency() - Align initial frequency value
+ * @dmc:	device for which the frequency is going to be set
+ * @bootloader_init_freq:	initial frequency set by the bootloader in KHz
+ *
+ * The initial bootloader frequency, which is present during boot, might be
+ * different that supported frequency values in the driver. It is possible
+ * due to different PLL settings or used PLL as a source.
+ * This function provides the 'initial_freq' for the devfreq framework
+ * statistics engine which supports only registered values. Thus, some alignment
+ * must be made.
+ */
+static unsigned long
+exynos5_dmc_align_init_freq(struct exynos5_dmc *dmc,
+			    unsigned long bootloader_init_freq)
+{
+	unsigned long aligned_freq;
+	int idx;
+
+	idx = find_target_freq_idx(dmc, bootloader_init_freq);
+	if (idx >= 0)
+		aligned_freq = dmc->opp[idx].freq_hz;
+	else
+		aligned_freq = dmc->opp[dmc->opp_count - 1].freq_hz;
+
+	return aligned_freq;
+}
+
+/**
+ * create_timings_aligned() - Create register values and align with standard
+ * @dmc:	device for which the frequency is going to be set
+ * @idx:	speed bin in the OPP table
+ * @clk_period_ps:	the period of the clock, known as tCK
+ *
+ * The function calculates timings and creates a register value ready for
+ * a frequency transition. The register contains a few timings. They are
+ * shifted by a known offset. The timing value is calculated based on memory
+ * specyfication: minimal time required and minimal cycles required.
+ */
+static int create_timings_aligned(struct exynos5_dmc *dmc, u32 *reg_timing_row,
+				  u32 *reg_timing_data, u32 *reg_timing_power,
+				  u32 clk_period_ps)
+{
+	u32 val;
+	const struct timing_reg *reg;
+
+	if (clk_period_ps == 0)
+		return -EINVAL;
+
+	*reg_timing_row = 0;
+	*reg_timing_data = 0;
+	*reg_timing_power = 0;
+
+	val = dmc->timings->tRFC / clk_period_ps;
+	val += dmc->timings->tRFC % clk_period_ps ? 1 : 0;
+	val = max(val, dmc->min_tck->tRFC);
+	reg = &timing_row[0];
+	*reg_timing_row |= TIMING_VAL2REG(reg, val);
+
+	val = dmc->timings->tRRD / clk_period_ps;
+	val += dmc->timings->tRRD % clk_period_ps ? 1 : 0;
+	val = max(val, dmc->min_tck->tRRD);
+	reg = &timing_row[1];
+	*reg_timing_row |= TIMING_VAL2REG(reg, val);
+
+	val = dmc->timings->tRPab / clk_period_ps;
+	val += dmc->timings->tRPab % clk_period_ps ? 1 : 0;
+	val = max(val, dmc->min_tck->tRPab);
+	reg = &timing_row[2];
+	*reg_timing_row |= TIMING_VAL2REG(reg, val);
+
+	val = dmc->timings->tRCD / clk_period_ps;
+	val += dmc->timings->tRCD % clk_period_ps ? 1 : 0;
+	val = max(val, dmc->min_tck->tRCD);
+	reg = &timing_row[3];
+	*reg_timing_row |= TIMING_VAL2REG(reg, val);
+
+	val = dmc->timings->tRC / clk_period_ps;
+	val += dmc->timings->tRC % clk_period_ps ? 1 : 0;
+	val = max(val, dmc->min_tck->tRC);
+	reg = &timing_row[4];
+	*reg_timing_row |= TIMING_VAL2REG(reg, val);
+
+	val = dmc->timings->tRAS / clk_period_ps;
+	val += dmc->timings->tRAS % clk_period_ps ? 1 : 0;
+	val = max(val, dmc->min_tck->tRAS);
+	reg = &timing_row[5];
+	*reg_timing_row |= TIMING_VAL2REG(reg, val);
+
+	/* data related timings */
+	val = dmc->timings->tWTR / clk_period_ps;
+	val += dmc->timings->tWTR % clk_period_ps ? 1 : 0;
+	val = max(val, dmc->min_tck->tWTR);
+	reg = &timing_data[0];
+	*reg_timing_data |= TIMING_VAL2REG(reg, val);
+
+	val = dmc->timings->tWR / clk_period_ps;
+	val += dmc->timings->tWR % clk_period_ps ? 1 : 0;
+	val = max(val, dmc->min_tck->tWR);
+	reg = &timing_data[1];
+	*reg_timing_data |= TIMING_VAL2REG(reg, val);
+
+	val = dmc->timings->tRTP / clk_period_ps;
+	val += dmc->timings->tRTP % clk_period_ps ? 1 : 0;
+	val = max(val, dmc->min_tck->tRTP);
+	reg = &timing_data[2];
+	*reg_timing_data |= TIMING_VAL2REG(reg, val);
+
+	val = dmc->timings->tW2W_C2C / clk_period_ps;
+	val += dmc->timings->tW2W_C2C % clk_period_ps ? 1 : 0;
+	val = max(val, dmc->min_tck->tW2W_C2C);
+	reg = &timing_data[3];
+	*reg_timing_data |= TIMING_VAL2REG(reg, val);
+
+	val = dmc->timings->tR2R_C2C / clk_period_ps;
+	val += dmc->timings->tR2R_C2C % clk_period_ps ? 1 : 0;
+	val = max(val, dmc->min_tck->tR2R_C2C);
+	reg = &timing_data[4];
+	*reg_timing_data |= TIMING_VAL2REG(reg, val);
+
+	val = dmc->timings->tWL / clk_period_ps;
+	val += dmc->timings->tWL % clk_period_ps ? 1 : 0;
+	val = max(val, dmc->min_tck->tWL);
+	reg = &timing_data[5];
+	*reg_timing_data |= TIMING_VAL2REG(reg, val);
+
+	val = dmc->timings->tDQSCK / clk_period_ps;
+	val += dmc->timings->tDQSCK % clk_period_ps ? 1 : 0;
+	val = max(val, dmc->min_tck->tDQSCK);
+	reg = &timing_data[6];
+	*reg_timing_data |= TIMING_VAL2REG(reg, val);
+
+	val = dmc->timings->tRL / clk_period_ps;
+	val += dmc->timings->tRL % clk_period_ps ? 1 : 0;
+	val = max(val, dmc->min_tck->tRL);
+	reg = &timing_data[7];
+	*reg_timing_data |= TIMING_VAL2REG(reg, val);
+
+	/* power related timings */
+	val = dmc->timings->tFAW / clk_period_ps;
+	val += dmc->timings->tFAW % clk_period_ps ? 1 : 0;
+	val = max(val, dmc->min_tck->tXP);
+	reg = &timing_power[0];
+	*reg_timing_power |= TIMING_VAL2REG(reg, val);
+
+	val = dmc->timings->tXSR / clk_period_ps;
+	val += dmc->timings->tXSR % clk_period_ps ? 1 : 0;
+	val = max(val, dmc->min_tck->tXSR);
+	reg = &timing_power[1];
+	*reg_timing_power |= TIMING_VAL2REG(reg, val);
+
+	val = dmc->timings->tXP / clk_period_ps;
+	val += dmc->timings->tXP % clk_period_ps ? 1 : 0;
+	val = max(val, dmc->min_tck->tXP);
+	reg = &timing_power[2];
+	*reg_timing_power |= TIMING_VAL2REG(reg, val);
+
+	val = dmc->timings->tCKE / clk_period_ps;
+	val += dmc->timings->tCKE % clk_period_ps ? 1 : 0;
+	val = max(val, dmc->min_tck->tCKE);
+	reg = &timing_power[3];
+	*reg_timing_power |= TIMING_VAL2REG(reg, val);
+
+	val = dmc->timings->tMRD / clk_period_ps;
+	val += dmc->timings->tMRD % clk_period_ps ? 1 : 0;
+	val = max(val, dmc->min_tck->tMRD);
+	reg = &timing_power[4];
+	*reg_timing_power |= TIMING_VAL2REG(reg, val);
+
+	return 0;
+}
+
+/**
+ * of_get_dram_timings() - helper function for parsing DT settings for DRAM
+ * @dmc:        device for which the frequency is going to be set
+ *
+ * The function parses DT entries with DRAM information.
+ */
+static int of_get_dram_timings(struct exynos5_dmc *dmc)
+{
+	int ret = 0;
+	int idx;
+	struct device_node *np_ddr;
+	u32 freq_mhz, clk_period_ps;
+
+	np_ddr = of_parse_phandle(dmc->dev->of_node, "device-handle", 0);
+	if (!np_ddr) {
+		dev_warn(dmc->dev, "could not find 'device-handle' in DT\n");
+		return -EINVAL;
+	}
+
+	dmc->timing_row = devm_kmalloc_array(dmc->dev, TIMING_COUNT,
+					     sizeof(u32), GFP_KERNEL);
+	if (!dmc->timing_row)
+		return -ENOMEM;
+
+	dmc->timing_data = devm_kmalloc_array(dmc->dev, TIMING_COUNT,
+					      sizeof(u32), GFP_KERNEL);
+	if (!dmc->timing_data)
+		return -ENOMEM;
+
+	dmc->timing_power = devm_kmalloc_array(dmc->dev, TIMING_COUNT,
+					       sizeof(u32), GFP_KERNEL);
+	if (!dmc->timing_power)
+		return -ENOMEM;
+
+	dmc->timings = of_lpddr3_get_ddr_timings(np_ddr, dmc->dev,
+						 DDR_TYPE_LPDDR3,
+						 &dmc->timings_arr_size);
+	if (!dmc->timings) {
+		of_node_put(np_ddr);
+		dev_warn(dmc->dev, "could not get timings from DT\n");
+		return -EINVAL;
+	}
+
+	dmc->min_tck = of_lpddr3_get_min_tck(np_ddr, dmc->dev);
+	if (!dmc->min_tck) {
+		of_node_put(np_ddr);
+		dev_warn(dmc->dev, "could not get tck from DT\n");
+		return -EINVAL;
+	}
+
+	/* Sorted array of OPPs with frequency ascending */
+	for (idx = 0; idx < dmc->opp_count; idx++) {
+		freq_mhz = dmc->opp[idx].freq_hz / 1000000;
+		clk_period_ps = 1000000 / freq_mhz;
+
+		ret = create_timings_aligned(dmc, &dmc->timing_row[idx],
+					     &dmc->timing_data[idx],
+					     &dmc->timing_power[idx],
+					     clk_period_ps);
+	}
+
+	of_node_put(np_ddr);
+
+	/* Take the highest frequency's timings as 'bypass' */
+	dmc->bypass_timing_row = dmc->timing_row[idx - 1];
+	dmc->bypass_timing_data = dmc->timing_data[idx - 1];
+	dmc->bypass_timing_power = dmc->timing_power[idx - 1];
+
+	return ret;
+}
+
+/**
+ * exynos5_dmc_init_clks() - Initialize clocks needed for DMC operation.
+ * @dmc:	DMC structure containing needed fields
+ *
+ * Get the needed clocks defined in DT device, enable and set the right parents.
+ * Read current frequency and initialize the initial rate for governor.
+ */
+static int exynos5_dmc_init_clks(struct exynos5_dmc *dmc)
+{
+	int ret;
+	unsigned long target_volt = 0;
+	unsigned long target_rate = 0;
+	unsigned int tmp;
+
+	dmc->fout_spll = devm_clk_get(dmc->dev, "fout_spll");
+	if (IS_ERR(dmc->fout_spll))
+		return PTR_ERR(dmc->fout_spll);
+
+	dmc->fout_bpll = devm_clk_get(dmc->dev, "fout_bpll");
+	if (IS_ERR(dmc->fout_bpll))
+		return PTR_ERR(dmc->fout_bpll);
+
+	dmc->mout_mclk_cdrex = devm_clk_get(dmc->dev, "mout_mclk_cdrex");
+	if (IS_ERR(dmc->mout_mclk_cdrex))
+		return PTR_ERR(dmc->mout_mclk_cdrex);
+
+	dmc->mout_bpll = devm_clk_get(dmc->dev, "mout_bpll");
+	if (IS_ERR(dmc->mout_bpll))
+		return PTR_ERR(dmc->mout_bpll);
+
+	dmc->mout_mx_mspll_ccore = devm_clk_get(dmc->dev,
+						"mout_mx_mspll_ccore");
+	if (IS_ERR(dmc->mout_mx_mspll_ccore))
+		return PTR_ERR(dmc->mout_mx_mspll_ccore);
+
+	dmc->mout_spll = devm_clk_get(dmc->dev, "ff_dout_spll2");
+	if (IS_ERR(dmc->mout_spll)) {
+		dmc->mout_spll = devm_clk_get(dmc->dev, "mout_sclk_spll");
+		if (IS_ERR(dmc->mout_spll))
+			return PTR_ERR(dmc->mout_spll);
+	}
+
+	/*
+	 * Convert frequency to KHz values and set it for the governor.
+	 */
+	dmc->curr_rate = clk_get_rate(dmc->mout_mclk_cdrex);
+	dmc->curr_rate = exynos5_dmc_align_init_freq(dmc, dmc->curr_rate);
+	exynos5_dmc_df_profile.initial_freq = dmc->curr_rate;
+
+	ret = exynos5_dmc_get_volt_freq(dmc, &dmc->curr_rate, &target_rate,
+					&target_volt, 0);
+	if (ret)
+		return ret;
+
+	dmc->curr_volt = target_volt;
+
+	clk_set_parent(dmc->mout_mx_mspll_ccore, dmc->mout_spll);
+
+	dmc->bypass_rate = clk_get_rate(dmc->mout_mx_mspll_ccore);
+
+	clk_prepare_enable(dmc->fout_bpll);
+	clk_prepare_enable(dmc->mout_bpll);
+
+	/*
+	 * Some bootloaders do not set clock routes correctly.
+	 * Stop one path in clocks to PHY.
+	 */
+	regmap_read(dmc->clk_regmap, CDREX_LPDDR3PHY_CLKM_SRC, &tmp);
+	tmp &= ~(BIT(1) | BIT(0));
+	regmap_write(dmc->clk_regmap, CDREX_LPDDR3PHY_CLKM_SRC, tmp);
+
+	return 0;
+}
+
+/**
+ * exynos5_performance_counters_init() - Initializes performance DMC's counters
+ * @dmc:	DMC for which it does the setup
+ *
+ * Initialization of performance counters in DMC for estimating usage.
+ * The counter's values are used for calculation of a memory bandwidth and based
+ * on that the governor changes the frequency.
+ * The counters are not used when the governor is GOVERNOR_USERSPACE.
+ */
+static int exynos5_performance_counters_init(struct exynos5_dmc *dmc)
+{
+	int counters_size;
+	int ret, i;
+
+	dmc->num_counters = devfreq_event_get_edev_count(dmc->dev);
+	if (dmc->num_counters < 0) {
+		dev_err(dmc->dev, "could not get devfreq-event counters\n");
+		return dmc->num_counters;
+	}
+
+	counters_size = sizeof(struct devfreq_event_dev) * dmc->num_counters;
+	dmc->counter = devm_kzalloc(dmc->dev, counters_size, GFP_KERNEL);
+	if (!dmc->counter)
+		return -ENOMEM;
+
+	for (i = 0; i < dmc->num_counters; i++) {
+		dmc->counter[i] =
+			devfreq_event_get_edev_by_phandle(dmc->dev, i);
+		if (IS_ERR_OR_NULL(dmc->counter[i]))
+			return -EPROBE_DEFER;
+	}
+
+	ret = exynos5_counters_enable_edev(dmc);
+	if (ret < 0) {
+		dev_err(dmc->dev, "could not enable event counter\n");
+		return ret;
+	}
+
+	ret = exynos5_counters_set_event(dmc);
+	if (ret < 0) {
+		exynos5_counters_disable_edev(dmc);
+		dev_err(dmc->dev, "could not set event counter\n");
+		return ret;
+	}
+
+	return 0;
+}
+
+/**
+ * exynos5_dmc_set_pause_on_switching() - Controls a pause feature in DMC
+ * @dmc:	device which is used for changing this feature
+ * @set:	a boolean state passing enable/disable request
+ *
+ * There is a need of pausing DREX DMC when divider or MUX in clock tree
+ * changes its configuration. In such situation access to the memory is blocked
+ * in DMC automatically. This feature is used when clock frequency change
+ * request appears and touches clock tree.
+ */
+static inline int exynos5_dmc_set_pause_on_switching(struct exynos5_dmc *dmc)
+{
+	unsigned int val;
+	int ret;
+
+	ret = regmap_read(dmc->clk_regmap, CDREX_PAUSE, &val);
+	if (ret)
+		return ret;
+
+	val |= 1UL;
+	regmap_write(dmc->clk_regmap, CDREX_PAUSE, val);
+
+	return 0;
+}
+
+static irqreturn_t dmc_irq_thread(int irq, void *priv)
+{
+	int res;
+	struct exynos5_dmc *dmc = priv;
+
+	mutex_lock(&dmc->df->lock);
+
+	exynos5_dmc_perf_events_check(dmc);
+
+	res = update_devfreq(dmc->df);
+	if (res)
+		dev_warn(dmc->dev, "devfreq failed with %d\n", res);
+
+	mutex_unlock(&dmc->df->lock);
+
+	return IRQ_HANDLED;
+}
+
+/**
+ * exynos5_dmc_probe() - Probe function for the DMC driver
+ * @pdev:	platform device for which the driver is going to be initialized
+ *
+ * Initialize basic components: clocks, regulators, performance counters, etc.
+ * Read out product version and based on the information setup
+ * internal structures for the controller (frequency and voltage) and for DRAM
+ * memory parameters: timings for each operating frequency.
+ * Register new devfreq device for controlling DVFS of the DMC.
+ */
+static int exynos5_dmc_probe(struct platform_device *pdev)
+{
+	int ret = 0;
+	struct device *dev = &pdev->dev;
+	struct device_node *np = dev->of_node;
+	struct exynos5_dmc *dmc;
+	struct resource *res;
+	int irq[2];
+
+	dmc = devm_kzalloc(dev, sizeof(*dmc), GFP_KERNEL);
+	if (!dmc)
+		return -ENOMEM;
+
+	mutex_init(&dmc->lock);
+
+	dmc->dev = dev;
+	platform_set_drvdata(pdev, dmc);
+
+	res = platform_get_resource(pdev, IORESOURCE_MEM, 0);
+	dmc->base_drexi0 = devm_ioremap_resource(dev, res);
+	if (IS_ERR(dmc->base_drexi0))
+		return PTR_ERR(dmc->base_drexi0);
+
+	res = platform_get_resource(pdev, IORESOURCE_MEM, 1);
+	dmc->base_drexi1 = devm_ioremap_resource(dev, res);
+	if (IS_ERR(dmc->base_drexi1))
+		return PTR_ERR(dmc->base_drexi1);
+
+	dmc->clk_regmap = syscon_regmap_lookup_by_phandle(np,
+				"samsung,syscon-clk");
+	if (IS_ERR(dmc->clk_regmap))
+		return PTR_ERR(dmc->clk_regmap);
+
+	ret = exynos5_init_freq_table(dmc, &exynos5_dmc_df_profile);
+	if (ret) {
+		dev_warn(dev, "couldn't initialize frequency settings\n");
+		return ret;
+	}
+
+	dmc->vdd_mif = devm_regulator_get(dev, "vdd");
+	if (IS_ERR(dmc->vdd_mif)) {
+		ret = PTR_ERR(dmc->vdd_mif);
+		return ret;
+	}
+
+	ret = exynos5_dmc_init_clks(dmc);
+	if (ret)
+		return ret;
+
+	ret = of_get_dram_timings(dmc);
+	if (ret) {
+		dev_warn(dev, "couldn't initialize timings settings\n");
+		goto remove_clocks;
+	}
+
+	ret = exynos5_dmc_set_pause_on_switching(dmc);
+	if (ret) {
+		dev_warn(dev, "couldn't get access to PAUSE register\n");
+		goto remove_clocks;
+	}
+
+	/* There is two modes in which the driver works: polling or IRQ */
+	irq[0] = platform_get_irq_byname(pdev, "drex_0");
+	irq[1] = platform_get_irq_byname(pdev, "drex_1");
+	if (irq[0] > 0 && irq[1] > 0) {
+		ret = devm_request_threaded_irq(dev, irq[0], NULL,
+						dmc_irq_thread, IRQF_ONESHOT,
+						dev_name(dev), dmc);
+		if (ret) {
+			dev_err(dev, "couldn't grab IRQ\n");
+			goto remove_clocks;
+		}
+
+		ret = devm_request_threaded_irq(dev, irq[1], NULL,
+						dmc_irq_thread, IRQF_ONESHOT,
+						dev_name(dev), dmc);
+		if (ret) {
+			dev_err(dev, "couldn't grab IRQ\n");
+			goto remove_clocks;
+		}
+
+		/*
+		 * Setup default thresholds for the devfreq governor.
+		 * The values are chosen based on experiments.
+		 */
+		dmc->gov_data.upthreshold = 55;
+		dmc->gov_data.downdifferential = 5;
+
+		exynos5_dmc_enable_perf_events(dmc);
+
+		dmc->in_irq_mode = 1;
+	} else {
+		ret = exynos5_performance_counters_init(dmc);
+		if (ret) {
+			dev_warn(dev, "couldn't probe performance counters\n");
+			goto remove_clocks;
+		}
+
+		/*
+		 * Setup default thresholds for the devfreq governor.
+		 * The values are chosen based on experiments.
+		 */
+		dmc->gov_data.upthreshold = 30;
+		dmc->gov_data.downdifferential = 5;
+
+		exynos5_dmc_df_profile.polling_ms = 500;
+	}
+
+
+	dmc->df = devm_devfreq_add_device(dev, &exynos5_dmc_df_profile,
+					  DEVFREQ_GOV_SIMPLE_ONDEMAND,
+					  &dmc->gov_data);
+
+	if (IS_ERR(dmc->df)) {
+		ret = PTR_ERR(dmc->df);
+		goto err_devfreq_add;
+	}
+
+	if (dmc->in_irq_mode)
+		exynos5_dmc_start_perf_events(dmc, PERF_COUNTER_START_VALUE);
+
+	dev_info(dev, "DMC initialized\n");
+
+	return 0;
+
+err_devfreq_add:
+	if (dmc->in_irq_mode)
+		exynos5_dmc_disable_perf_events(dmc);
+	else
+		exynos5_counters_disable_edev(dmc);
+remove_clocks:
+	clk_disable_unprepare(dmc->mout_bpll);
+	clk_disable_unprepare(dmc->fout_bpll);
+
+	return ret;
+}
+
+/**
+ * exynos5_dmc_remove() - Remove function for the platform device
+ * @pdev:	platform device which is going to be removed
+ *
+ * The function relies on 'devm' framework function which automatically
+ * clean the device's resources. It just calls explicitly disable function for
+ * the performance counters.
+ */
+static int exynos5_dmc_remove(struct platform_device *pdev)
+{
+	struct exynos5_dmc *dmc = dev_get_drvdata(&pdev->dev);
+
+	if (dmc->in_irq_mode)
+		exynos5_dmc_disable_perf_events(dmc);
+	else
+		exynos5_counters_disable_edev(dmc);
+
+	clk_disable_unprepare(dmc->mout_bpll);
+	clk_disable_unprepare(dmc->fout_bpll);
+
+	dev_pm_opp_remove_table(dmc->dev);
+
+	return 0;
+}
+
+static const struct of_device_id exynos5_dmc_of_match[] = {
+	{ .compatible = "samsung,exynos5422-dmc", },
+	{ },
+};
+MODULE_DEVICE_TABLE(of, exynos5_dmc_of_match);
+
+static struct platform_driver exynos5_dmc_platdrv = {
+	.probe	= exynos5_dmc_probe,
+	.remove = exynos5_dmc_remove,
+	.driver = {
+		.name	= "exynos5-dmc",
+		.of_match_table = exynos5_dmc_of_match,
+	},
+};
+module_platform_driver(exynos5_dmc_platdrv);
+MODULE_DESCRIPTION("Driver for Exynos5422 Dynamic Memory Controller dynamic frequency and voltage change");
+MODULE_LICENSE("GPL v2");
+MODULE_AUTHOR("Lukasz Luba");
diff --git a/drivers/memory/tegra/Kconfig b/drivers/memory/tegra/Kconfig
index 4680124ddcab..fbfbaada61a2 100644
--- a/drivers/memory/tegra/Kconfig
+++ b/drivers/memory/tegra/Kconfig
@@ -17,6 +17,16 @@ config TEGRA20_EMC
 	  This driver is required to change memory timings / clock rate for
 	  external memory.
 
+config TEGRA30_EMC
+	bool "NVIDIA Tegra30 External Memory Controller driver"
+	default y
+	depends on TEGRA_MC && ARCH_TEGRA_3x_SOC
+	help
+	  This driver is for the External Memory Controller (EMC) found on
+	  Tegra30 chips. The EMC controls the external DRAM on the board.
+	  This driver is required to change memory timings / clock rate for
+	  external memory.
+
 config TEGRA124_EMC
 	bool "NVIDIA Tegra124 External Memory Controller driver"
 	default y
diff --git a/drivers/memory/tegra/Makefile b/drivers/memory/tegra/Makefile
index 3971a6b7c487..3d23c4261104 100644
--- a/drivers/memory/tegra/Makefile
+++ b/drivers/memory/tegra/Makefile
@@ -11,5 +11,6 @@ tegra-mc-$(CONFIG_ARCH_TEGRA_210_SOC) += tegra210.o
 obj-$(CONFIG_TEGRA_MC) += tegra-mc.o
 
 obj-$(CONFIG_TEGRA20_EMC)  += tegra20-emc.o
+obj-$(CONFIG_TEGRA30_EMC)  += tegra30-emc.o
 obj-$(CONFIG_TEGRA124_EMC) += tegra124-emc.o
 obj-$(CONFIG_ARCH_TEGRA_186_SOC) += tegra186.o
diff --git a/drivers/memory/tegra/mc.c b/drivers/memory/tegra/mc.c
index 3d8d322511c5..ec8403557ed4 100644
--- a/drivers/memory/tegra/mc.c
+++ b/drivers/memory/tegra/mc.c
@@ -5,6 +5,7 @@
 
 #include <linux/clk.h>
 #include <linux/delay.h>
+#include <linux/dma-mapping.h>
 #include <linux/interrupt.h>
 #include <linux/kernel.h>
 #include <linux/module.h>
@@ -18,39 +19,6 @@
 
 #include "mc.h"
 
-#define MC_INTSTATUS 0x000
-
-#define MC_INTMASK 0x004
-
-#define MC_ERR_STATUS 0x08
-#define  MC_ERR_STATUS_TYPE_SHIFT 28
-#define  MC_ERR_STATUS_TYPE_INVALID_SMMU_PAGE (6 << MC_ERR_STATUS_TYPE_SHIFT)
-#define  MC_ERR_STATUS_TYPE_MASK (0x7 << MC_ERR_STATUS_TYPE_SHIFT)
-#define  MC_ERR_STATUS_READABLE (1 << 27)
-#define  MC_ERR_STATUS_WRITABLE (1 << 26)
-#define  MC_ERR_STATUS_NONSECURE (1 << 25)
-#define  MC_ERR_STATUS_ADR_HI_SHIFT 20
-#define  MC_ERR_STATUS_ADR_HI_MASK 0x3
-#define  MC_ERR_STATUS_SECURITY (1 << 17)
-#define  MC_ERR_STATUS_RW (1 << 16)
-
-#define MC_ERR_ADR 0x0c
-
-#define MC_GART_ERROR_REQ		0x30
-#define MC_DECERR_EMEM_OTHERS_STATUS	0x58
-#define MC_SECURITY_VIOLATION_STATUS	0x74
-
-#define MC_EMEM_ARB_CFG 0x90
-#define  MC_EMEM_ARB_CFG_CYCLES_PER_UPDATE(x)	(((x) & 0x1ff) << 0)
-#define  MC_EMEM_ARB_CFG_CYCLES_PER_UPDATE_MASK	0x1ff
-#define MC_EMEM_ARB_MISC0 0xd8
-
-#define MC_EMEM_ADR_CFG 0x54
-#define MC_EMEM_ADR_CFG_EMEM_NUMDEV BIT(0)
-
-#define MC_TIMING_CONTROL		0xfc
-#define MC_TIMING_UPDATE		BIT(0)
-
 static const struct of_device_id tegra_mc_of_match[] = {
 #ifdef CONFIG_ARCH_TEGRA_2x_SOC
 	{ .compatible = "nvidia,tegra20-mc-gart", .data = &tegra20_mc_soc },
@@ -307,7 +275,7 @@ static int tegra_mc_setup_latency_allowance(struct tegra_mc *mc)
 	return 0;
 }
 
-void tegra_mc_write_emem_configuration(struct tegra_mc *mc, unsigned long rate)
+int tegra_mc_write_emem_configuration(struct tegra_mc *mc, unsigned long rate)
 {
 	unsigned int i;
 	struct tegra_mc_timing *timing = NULL;
@@ -322,11 +290,13 @@ void tegra_mc_write_emem_configuration(struct tegra_mc *mc, unsigned long rate)
 	if (!timing) {
 		dev_err(mc->dev, "no memory timing registered for rate %lu\n",
 			rate);
-		return;
+		return -EINVAL;
 	}
 
 	for (i = 0; i < mc->soc->num_emem_regs; ++i)
 		mc_writel(mc, timing->emem_data[i], mc->soc->emem_regs[i]);
+
+	return 0;
 }
 
 unsigned int tegra_mc_get_emem_device_count(struct tegra_mc *mc)
@@ -626,6 +596,7 @@ static int tegra_mc_probe(struct platform_device *pdev)
 	struct resource *res;
 	struct tegra_mc *mc;
 	void *isr;
+	u64 mask;
 	int err;
 
 	mc = devm_kzalloc(&pdev->dev, sizeof(*mc), GFP_KERNEL);
@@ -637,6 +608,14 @@ static int tegra_mc_probe(struct platform_device *pdev)
 	mc->soc = of_device_get_match_data(&pdev->dev);
 	mc->dev = &pdev->dev;
 
+	mask = DMA_BIT_MASK(mc->soc->num_address_bits);
+
+	err = dma_coerce_mask_and_coherent(&pdev->dev, mask);
+	if (err < 0) {
+		dev_err(&pdev->dev, "failed to set DMA mask: %d\n", err);
+		return err;
+	}
+
 	/* length of MC tick in nanoseconds */
 	mc->tick = 30;
 
@@ -658,6 +637,9 @@ static int tegra_mc_probe(struct platform_device *pdev)
 	} else
 #endif
 	{
+		/* ensure that debug features are disabled */
+		mc_writel(mc, 0x00000000, MC_TIMING_CONTROL_DBG);
+
 		err = tegra_mc_setup_latency_allowance(mc);
 		if (err < 0) {
 			dev_err(&pdev->dev,
diff --git a/drivers/memory/tegra/mc.h b/drivers/memory/tegra/mc.h
index f9353494b708..957c6eb74ff9 100644
--- a/drivers/memory/tegra/mc.h
+++ b/drivers/memory/tegra/mc.h
@@ -6,20 +6,76 @@
 #ifndef MEMORY_TEGRA_MC_H
 #define MEMORY_TEGRA_MC_H
 
+#include <linux/bits.h>
 #include <linux/io.h>
 #include <linux/types.h>
 
 #include <soc/tegra/mc.h>
 
-#define MC_INT_DECERR_MTS (1 << 16)
-#define MC_INT_SECERR_SEC (1 << 13)
-#define MC_INT_DECERR_VPR (1 << 12)
-#define MC_INT_INVALID_APB_ASID_UPDATE (1 << 11)
-#define MC_INT_INVALID_SMMU_PAGE (1 << 10)
-#define MC_INT_ARBITRATION_EMEM (1 << 9)
-#define MC_INT_SECURITY_VIOLATION (1 << 8)
-#define MC_INT_INVALID_GART_PAGE (1 << 7)
-#define MC_INT_DECERR_EMEM (1 << 6)
+#define MC_INTSTATUS					0x00
+#define MC_INTMASK					0x04
+#define MC_ERR_STATUS					0x08
+#define MC_ERR_ADR					0x0c
+#define MC_GART_ERROR_REQ				0x30
+#define MC_EMEM_ADR_CFG					0x54
+#define MC_DECERR_EMEM_OTHERS_STATUS			0x58
+#define MC_SECURITY_VIOLATION_STATUS			0x74
+#define MC_EMEM_ARB_CFG					0x90
+#define MC_EMEM_ARB_OUTSTANDING_REQ			0x94
+#define MC_EMEM_ARB_TIMING_RCD				0x98
+#define MC_EMEM_ARB_TIMING_RP				0x9c
+#define MC_EMEM_ARB_TIMING_RC				0xa0
+#define MC_EMEM_ARB_TIMING_RAS				0xa4
+#define MC_EMEM_ARB_TIMING_FAW				0xa8
+#define MC_EMEM_ARB_TIMING_RRD				0xac
+#define MC_EMEM_ARB_TIMING_RAP2PRE			0xb0
+#define MC_EMEM_ARB_TIMING_WAP2PRE			0xb4
+#define MC_EMEM_ARB_TIMING_R2R				0xb8
+#define MC_EMEM_ARB_TIMING_W2W				0xbc
+#define MC_EMEM_ARB_TIMING_R2W				0xc0
+#define MC_EMEM_ARB_TIMING_W2R				0xc4
+#define MC_EMEM_ARB_DA_TURNS				0xd0
+#define MC_EMEM_ARB_DA_COVERS				0xd4
+#define MC_EMEM_ARB_MISC0				0xd8
+#define MC_EMEM_ARB_MISC1				0xdc
+#define MC_EMEM_ARB_RING1_THROTTLE			0xe0
+#define MC_EMEM_ARB_OVERRIDE				0xe8
+#define MC_TIMING_CONTROL_DBG				0xf8
+#define MC_TIMING_CONTROL				0xfc
+
+#define MC_INT_DECERR_MTS				BIT(16)
+#define MC_INT_SECERR_SEC				BIT(13)
+#define MC_INT_DECERR_VPR				BIT(12)
+#define MC_INT_INVALID_APB_ASID_UPDATE			BIT(11)
+#define MC_INT_INVALID_SMMU_PAGE			BIT(10)
+#define MC_INT_ARBITRATION_EMEM				BIT(9)
+#define MC_INT_SECURITY_VIOLATION			BIT(8)
+#define MC_INT_INVALID_GART_PAGE			BIT(7)
+#define MC_INT_DECERR_EMEM				BIT(6)
+
+#define MC_ERR_STATUS_TYPE_SHIFT			28
+#define MC_ERR_STATUS_TYPE_INVALID_SMMU_PAGE		(0x6 << 28)
+#define MC_ERR_STATUS_TYPE_MASK				(0x7 << 28)
+#define MC_ERR_STATUS_READABLE				BIT(27)
+#define MC_ERR_STATUS_WRITABLE				BIT(26)
+#define MC_ERR_STATUS_NONSECURE				BIT(25)
+#define MC_ERR_STATUS_ADR_HI_SHIFT			20
+#define MC_ERR_STATUS_ADR_HI_MASK			0x3
+#define MC_ERR_STATUS_SECURITY				BIT(17)
+#define MC_ERR_STATUS_RW				BIT(16)
+
+#define MC_EMEM_ADR_CFG_EMEM_NUMDEV			BIT(0)
+
+#define MC_EMEM_ARB_CFG_CYCLES_PER_UPDATE(x)		((x) & 0x1ff)
+#define MC_EMEM_ARB_CFG_CYCLES_PER_UPDATE_MASK		0x1ff
+
+#define MC_EMEM_ARB_OUTSTANDING_REQ_MAX_MASK		0x1ff
+#define MC_EMEM_ARB_OUTSTANDING_REQ_HOLDOFF_OVERRIDE	BIT(30)
+#define MC_EMEM_ARB_OUTSTANDING_REQ_LIMIT_ENABLE	BIT(31)
+
+#define MC_EMEM_ARB_OVERRIDE_EACK_MASK			0x3
+
+#define MC_TIMING_UPDATE				BIT(0)
 
 static inline u32 mc_readl(struct tegra_mc *mc, unsigned long offset)
 {
diff --git a/drivers/memory/tegra/tegra114.c b/drivers/memory/tegra/tegra114.c
index ac8351b5beeb..48ef01c3ff90 100644
--- a/drivers/memory/tegra/tegra114.c
+++ b/drivers/memory/tegra/tegra114.c
@@ -909,16 +909,18 @@ static const struct tegra_smmu_swgroup tegra114_swgroups[] = {
 	{ .name = "tsec",      .swgroup = TEGRA_SWGROUP_TSEC,      .reg = 0x294 },
 };
 
-static const unsigned int tegra114_group_display[] = {
+static const unsigned int tegra114_group_drm[] = {
 	TEGRA_SWGROUP_DC,
 	TEGRA_SWGROUP_DCB,
+	TEGRA_SWGROUP_G2,
+	TEGRA_SWGROUP_NV,
 };
 
 static const struct tegra_smmu_group_soc tegra114_groups[] = {
 	{
-		.name = "display",
-		.swgroups = tegra114_group_display,
-		.num_swgroups = ARRAY_SIZE(tegra114_group_display),
+		.name = "drm",
+		.swgroups = tegra114_group_drm,
+		.num_swgroups = ARRAY_SIZE(tegra114_group_drm),
 	},
 };
 
diff --git a/drivers/memory/tegra/tegra124.c b/drivers/memory/tegra/tegra124.c
index 5d0ccb2be206..493b5dc3a4b3 100644
--- a/drivers/memory/tegra/tegra124.c
+++ b/drivers/memory/tegra/tegra124.c
@@ -10,26 +10,6 @@
 
 #include "mc.h"
 
-#define MC_EMEM_ARB_CFG				0x90
-#define MC_EMEM_ARB_OUTSTANDING_REQ		0x94
-#define MC_EMEM_ARB_TIMING_RCD			0x98
-#define MC_EMEM_ARB_TIMING_RP			0x9c
-#define MC_EMEM_ARB_TIMING_RC			0xa0
-#define MC_EMEM_ARB_TIMING_RAS			0xa4
-#define MC_EMEM_ARB_TIMING_FAW			0xa8
-#define MC_EMEM_ARB_TIMING_RRD			0xac
-#define MC_EMEM_ARB_TIMING_RAP2PRE		0xb0
-#define MC_EMEM_ARB_TIMING_WAP2PRE		0xb4
-#define MC_EMEM_ARB_TIMING_R2R			0xb8
-#define MC_EMEM_ARB_TIMING_W2W			0xbc
-#define MC_EMEM_ARB_TIMING_R2W			0xc0
-#define MC_EMEM_ARB_TIMING_W2R			0xc4
-#define MC_EMEM_ARB_DA_TURNS			0xd0
-#define MC_EMEM_ARB_DA_COVERS			0xd4
-#define MC_EMEM_ARB_MISC0			0xd8
-#define MC_EMEM_ARB_MISC1			0xdc
-#define MC_EMEM_ARB_RING1_THROTTLE		0xe0
-
 static const struct tegra_mc_client tegra124_mc_clients[] = {
 	{
 		.id = 0x00,
@@ -974,16 +954,18 @@ static const struct tegra_smmu_swgroup tegra124_swgroups[] = {
 	{ .name = "vi",        .swgroup = TEGRA_SWGROUP_VI,        .reg = 0x280 },
 };
 
-static const unsigned int tegra124_group_display[] = {
+static const unsigned int tegra124_group_drm[] = {
 	TEGRA_SWGROUP_DC,
 	TEGRA_SWGROUP_DCB,
+	TEGRA_SWGROUP_GPU,
+	TEGRA_SWGROUP_VIC,
 };
 
 static const struct tegra_smmu_group_soc tegra124_groups[] = {
 	{
-		.name = "display",
-		.swgroups = tegra124_group_display,
-		.num_swgroups = ARRAY_SIZE(tegra124_group_display),
+		.name = "drm",
+		.swgroups = tegra124_group_drm,
+		.num_swgroups = ARRAY_SIZE(tegra124_group_drm),
 	},
 };
 
diff --git a/drivers/memory/tegra/tegra20-emc.c b/drivers/memory/tegra/tegra20-emc.c
index 9ee5bef49e47..1b23b1c34476 100644
--- a/drivers/memory/tegra/tegra20-emc.c
+++ b/drivers/memory/tegra/tegra20-emc.c
@@ -6,10 +6,11 @@
  */
 
 #include <linux/clk.h>
+#include <linux/clk/tegra.h>
 #include <linux/completion.h>
 #include <linux/err.h>
 #include <linux/interrupt.h>
-#include <linux/iopoll.h>
+#include <linux/io.h>
 #include <linux/kernel.h>
 #include <linux/module.h>
 #include <linux/of.h>
@@ -21,6 +22,7 @@
 
 #define EMC_INTSTATUS				0x000
 #define EMC_INTMASK				0x004
+#define EMC_DBG					0x008
 #define EMC_TIMING_CONTROL			0x028
 #define EMC_RC					0x02c
 #define EMC_RFC					0x030
@@ -79,6 +81,12 @@
 #define EMC_REFRESH_OVERFLOW_INT		BIT(3)
 #define EMC_CLKCHANGE_COMPLETE_INT		BIT(4)
 
+#define EMC_DBG_READ_MUX_ASSEMBLY		BIT(0)
+#define EMC_DBG_WRITE_MUX_ACTIVE		BIT(1)
+#define EMC_DBG_FORCE_UPDATE			BIT(2)
+#define EMC_DBG_READ_DQM_CTRL			BIT(9)
+#define EMC_DBG_CFG_PRIORITY			BIT(24)
+
 static const u16 emc_timing_registers[] = {
 	EMC_RC,
 	EMC_RFC,
@@ -137,9 +145,6 @@ struct tegra_emc {
 	struct device *dev;
 	struct completion clk_handshake_complete;
 	struct notifier_block clk_nb;
-	struct clk *backup_clk;
-	struct clk *emc_mux;
-	struct clk *pll_m;
 	struct clk *clk;
 	void __iomem *regs;
 
@@ -219,7 +224,7 @@ static int emc_prepare_timing_change(struct tegra_emc *emc, unsigned long rate)
 
 static int emc_complete_timing_change(struct tegra_emc *emc, bool flush)
 {
-	long timeout;
+	unsigned long timeout;
 
 	dev_dbg(emc->dev, "%s: flush %d\n", __func__, flush);
 
@@ -231,14 +236,10 @@ static int emc_complete_timing_change(struct tegra_emc *emc, bool flush)
 	}
 
 	timeout = wait_for_completion_timeout(&emc->clk_handshake_complete,
-					      usecs_to_jiffies(100));
+					      msecs_to_jiffies(100));
 	if (timeout == 0) {
 		dev_err(emc->dev, "EMC-CAR handshake failed\n");
 		return -EIO;
-	} else if (timeout < 0) {
-		dev_err(emc->dev, "failed to wait for EMC-CAR handshake: %ld\n",
-			timeout);
-		return timeout;
 	}
 
 	return 0;
@@ -363,6 +364,13 @@ static int tegra_emc_load_timings_from_dt(struct tegra_emc *emc,
 	sort(emc->timings, emc->num_timings, sizeof(*timing), cmp_timings,
 	     NULL);
 
+	dev_info(emc->dev,
+		 "got %u timings for RAM code %u (min %luMHz max %luMHz)\n",
+		 emc->num_timings,
+		 tegra_read_ram_code(),
+		 emc->timings[0].rate / 1000000,
+		 emc->timings[emc->num_timings - 1].rate / 1000000);
+
 	return 0;
 }
 
@@ -398,7 +406,7 @@ tegra_emc_find_node_by_ram_code(struct device *dev)
 static int emc_setup_hw(struct tegra_emc *emc)
 {
 	u32 intmask = EMC_REFRESH_OVERFLOW_INT | EMC_CLKCHANGE_COMPLETE_INT;
-	u32 emc_cfg;
+	u32 emc_cfg, emc_dbg;
 
 	emc_cfg = readl_relaxed(emc->regs + EMC_CFG_2);
 
@@ -421,42 +429,53 @@ static int emc_setup_hw(struct tegra_emc *emc)
 	writel_relaxed(intmask, emc->regs + EMC_INTMASK);
 	writel_relaxed(intmask, emc->regs + EMC_INTSTATUS);
 
+	/* ensure that unwanted debug features are disabled */
+	emc_dbg = readl_relaxed(emc->regs + EMC_DBG);
+	emc_dbg |= EMC_DBG_CFG_PRIORITY;
+	emc_dbg &= ~EMC_DBG_READ_MUX_ASSEMBLY;
+	emc_dbg &= ~EMC_DBG_WRITE_MUX_ACTIVE;
+	emc_dbg &= ~EMC_DBG_FORCE_UPDATE;
+	writel_relaxed(emc_dbg, emc->regs + EMC_DBG);
+
 	return 0;
 }
 
-static int emc_init(struct tegra_emc *emc, unsigned long rate)
+static long emc_round_rate(unsigned long rate,
+			   unsigned long min_rate,
+			   unsigned long max_rate,
+			   void *arg)
 {
-	int err;
+	struct emc_timing *timing = NULL;
+	struct tegra_emc *emc = arg;
+	unsigned int i;
 
-	err = clk_set_parent(emc->emc_mux, emc->backup_clk);
-	if (err) {
-		dev_err(emc->dev,
-			"failed to reparent to backup source: %d\n", err);
-		return err;
-	}
+	min_rate = min(min_rate, emc->timings[emc->num_timings - 1].rate);
 
-	err = clk_set_rate(emc->pll_m, rate);
-	if (err) {
-		dev_err(emc->dev,
-			"failed to change pll_m rate: %d\n", err);
-		return err;
-	}
+	for (i = 0; i < emc->num_timings; i++) {
+		if (emc->timings[i].rate < rate && i != emc->num_timings - 1)
+			continue;
 
-	err = clk_set_parent(emc->emc_mux, emc->pll_m);
-	if (err) {
-		dev_err(emc->dev,
-			"failed to reparent to pll_m: %d\n", err);
-		return err;
+		if (emc->timings[i].rate > max_rate) {
+			i = max(i, 1u) - 1;
+
+			if (emc->timings[i].rate < min_rate)
+				break;
+		}
+
+		if (emc->timings[i].rate < min_rate)
+			continue;
+
+		timing = &emc->timings[i];
+		break;
 	}
 
-	err = clk_set_rate(emc->clk, rate);
-	if (err) {
-		dev_err(emc->dev,
-			"failed to change emc rate: %d\n", err);
-		return err;
+	if (!timing) {
+		dev_err(emc->dev, "no timing for rate %lu min %lu max %lu\n",
+			rate, min_rate, max_rate);
+		return -EINVAL;
 	}
 
-	return 0;
+	return timing->rate;
 }
 
 static int tegra_emc_probe(struct platform_device *pdev)
@@ -515,57 +534,26 @@ static int tegra_emc_probe(struct platform_device *pdev)
 		return err;
 	}
 
+	tegra20_clk_set_emc_round_callback(emc_round_rate, emc);
+
 	emc->clk = devm_clk_get(&pdev->dev, "emc");
 	if (IS_ERR(emc->clk)) {
 		err = PTR_ERR(emc->clk);
 		dev_err(&pdev->dev, "failed to get emc clock: %d\n", err);
-		return err;
-	}
-
-	emc->pll_m = clk_get_sys(NULL, "pll_m");
-	if (IS_ERR(emc->pll_m)) {
-		err = PTR_ERR(emc->pll_m);
-		dev_err(&pdev->dev, "failed to get pll_m clock: %d\n", err);
-		return err;
-	}
-
-	emc->backup_clk = clk_get_sys(NULL, "pll_p");
-	if (IS_ERR(emc->backup_clk)) {
-		err = PTR_ERR(emc->backup_clk);
-		dev_err(&pdev->dev, "failed to get pll_p clock: %d\n", err);
-		goto put_pll_m;
-	}
-
-	emc->emc_mux = clk_get_parent(emc->clk);
-	if (IS_ERR(emc->emc_mux)) {
-		err = PTR_ERR(emc->emc_mux);
-		dev_err(&pdev->dev, "failed to get emc_mux clock: %d\n", err);
-		goto put_backup;
+		goto unset_cb;
 	}
 
 	err = clk_notifier_register(emc->clk, &emc->clk_nb);
 	if (err) {
 		dev_err(&pdev->dev, "failed to register clk notifier: %d\n",
 			err);
-		goto put_backup;
-	}
-
-	/* set DRAM clock rate to maximum */
-	err = emc_init(emc, emc->timings[emc->num_timings - 1].rate);
-	if (err) {
-		dev_err(&pdev->dev, "failed to initialize EMC clock rate: %d\n",
-			err);
-		goto unreg_notifier;
+		goto unset_cb;
 	}
 
 	return 0;
 
-unreg_notifier:
-	clk_notifier_unregister(emc->clk, &emc->clk_nb);
-put_backup:
-	clk_put(emc->backup_clk);
-put_pll_m:
-	clk_put(emc->pll_m);
+unset_cb:
+	tegra20_clk_set_emc_round_callback(NULL, NULL);
 
 	return err;
 }
diff --git a/drivers/memory/tegra/tegra30-emc.c b/drivers/memory/tegra/tegra30-emc.c
new file mode 100644
index 000000000000..6929980bf907
--- /dev/null
+++ b/drivers/memory/tegra/tegra30-emc.c
@@ -0,0 +1,1232 @@
+// SPDX-License-Identifier: GPL-2.0+
+/*
+ * Tegra30 External Memory Controller driver
+ *
+ * Based on downstream driver from NVIDIA and tegra124-emc.c
+ * Copyright (C) 2011-2014 NVIDIA Corporation
+ *
+ * Author: Dmitry Osipenko <digetx@gmail.com>
+ * Copyright (C) 2019 GRATE-DRIVER project
+ */
+
+#include <linux/clk.h>
+#include <linux/clk/tegra.h>
+#include <linux/completion.h>
+#include <linux/delay.h>
+#include <linux/err.h>
+#include <linux/interrupt.h>
+#include <linux/io.h>
+#include <linux/iopoll.h>
+#include <linux/kernel.h>
+#include <linux/module.h>
+#include <linux/of_platform.h>
+#include <linux/platform_device.h>
+#include <linux/sort.h>
+#include <linux/types.h>
+
+#include <soc/tegra/fuse.h>
+
+#include "mc.h"
+
+#define EMC_INTSTATUS				0x000
+#define EMC_INTMASK				0x004
+#define EMC_DBG					0x008
+#define EMC_CFG					0x00c
+#define EMC_REFCTRL				0x020
+#define EMC_TIMING_CONTROL			0x028
+#define EMC_RC					0x02c
+#define EMC_RFC					0x030
+#define EMC_RAS					0x034
+#define EMC_RP					0x038
+#define EMC_R2W					0x03c
+#define EMC_W2R					0x040
+#define EMC_R2P					0x044
+#define EMC_W2P					0x048
+#define EMC_RD_RCD				0x04c
+#define EMC_WR_RCD				0x050
+#define EMC_RRD					0x054
+#define EMC_REXT				0x058
+#define EMC_WDV					0x05c
+#define EMC_QUSE				0x060
+#define EMC_QRST				0x064
+#define EMC_QSAFE				0x068
+#define EMC_RDV					0x06c
+#define EMC_REFRESH				0x070
+#define EMC_BURST_REFRESH_NUM			0x074
+#define EMC_PDEX2WR				0x078
+#define EMC_PDEX2RD				0x07c
+#define EMC_PCHG2PDEN				0x080
+#define EMC_ACT2PDEN				0x084
+#define EMC_AR2PDEN				0x088
+#define EMC_RW2PDEN				0x08c
+#define EMC_TXSR				0x090
+#define EMC_TCKE				0x094
+#define EMC_TFAW				0x098
+#define EMC_TRPAB				0x09c
+#define EMC_TCLKSTABLE				0x0a0
+#define EMC_TCLKSTOP				0x0a4
+#define EMC_TREFBW				0x0a8
+#define EMC_QUSE_EXTRA				0x0ac
+#define EMC_ODT_WRITE				0x0b0
+#define EMC_ODT_READ				0x0b4
+#define EMC_WEXT				0x0b8
+#define EMC_CTT					0x0bc
+#define EMC_MRS_WAIT_CNT			0x0c8
+#define EMC_MRS					0x0cc
+#define EMC_EMRS				0x0d0
+#define EMC_SELF_REF				0x0e0
+#define EMC_MRW					0x0e8
+#define EMC_XM2DQSPADCTRL3			0x0f8
+#define EMC_FBIO_SPARE				0x100
+#define EMC_FBIO_CFG5				0x104
+#define EMC_FBIO_CFG6				0x114
+#define EMC_CFG_RSV				0x120
+#define EMC_AUTO_CAL_CONFIG			0x2a4
+#define EMC_AUTO_CAL_INTERVAL			0x2a8
+#define EMC_AUTO_CAL_STATUS			0x2ac
+#define EMC_STATUS				0x2b4
+#define EMC_CFG_2				0x2b8
+#define EMC_CFG_DIG_DLL				0x2bc
+#define EMC_CFG_DIG_DLL_PERIOD			0x2c0
+#define EMC_CTT_DURATION			0x2d8
+#define EMC_CTT_TERM_CTRL			0x2dc
+#define EMC_ZCAL_INTERVAL			0x2e0
+#define EMC_ZCAL_WAIT_CNT			0x2e4
+#define EMC_ZQ_CAL				0x2ec
+#define EMC_XM2CMDPADCTRL			0x2f0
+#define EMC_XM2DQSPADCTRL2			0x2fc
+#define EMC_XM2DQPADCTRL2			0x304
+#define EMC_XM2CLKPADCTRL			0x308
+#define EMC_XM2COMPPADCTRL			0x30c
+#define EMC_XM2VTTGENPADCTRL			0x310
+#define EMC_XM2VTTGENPADCTRL2			0x314
+#define EMC_XM2QUSEPADCTRL			0x318
+#define EMC_DLL_XFORM_DQS0			0x328
+#define EMC_DLL_XFORM_DQS1			0x32c
+#define EMC_DLL_XFORM_DQS2			0x330
+#define EMC_DLL_XFORM_DQS3			0x334
+#define EMC_DLL_XFORM_DQS4			0x338
+#define EMC_DLL_XFORM_DQS5			0x33c
+#define EMC_DLL_XFORM_DQS6			0x340
+#define EMC_DLL_XFORM_DQS7			0x344
+#define EMC_DLL_XFORM_QUSE0			0x348
+#define EMC_DLL_XFORM_QUSE1			0x34c
+#define EMC_DLL_XFORM_QUSE2			0x350
+#define EMC_DLL_XFORM_QUSE3			0x354
+#define EMC_DLL_XFORM_QUSE4			0x358
+#define EMC_DLL_XFORM_QUSE5			0x35c
+#define EMC_DLL_XFORM_QUSE6			0x360
+#define EMC_DLL_XFORM_QUSE7			0x364
+#define EMC_DLL_XFORM_DQ0			0x368
+#define EMC_DLL_XFORM_DQ1			0x36c
+#define EMC_DLL_XFORM_DQ2			0x370
+#define EMC_DLL_XFORM_DQ3			0x374
+#define EMC_DLI_TRIM_TXDQS0			0x3a8
+#define EMC_DLI_TRIM_TXDQS1			0x3ac
+#define EMC_DLI_TRIM_TXDQS2			0x3b0
+#define EMC_DLI_TRIM_TXDQS3			0x3b4
+#define EMC_DLI_TRIM_TXDQS4			0x3b8
+#define EMC_DLI_TRIM_TXDQS5			0x3bc
+#define EMC_DLI_TRIM_TXDQS6			0x3c0
+#define EMC_DLI_TRIM_TXDQS7			0x3c4
+#define EMC_STALL_THEN_EXE_BEFORE_CLKCHANGE	0x3c8
+#define EMC_STALL_THEN_EXE_AFTER_CLKCHANGE	0x3cc
+#define EMC_UNSTALL_RW_AFTER_CLKCHANGE		0x3d0
+#define EMC_SEL_DPD_CTRL			0x3d8
+#define EMC_PRE_REFRESH_REQ_CNT			0x3dc
+#define EMC_DYN_SELF_REF_CONTROL		0x3e0
+#define EMC_TXSRDLL				0x3e4
+
+#define EMC_STATUS_TIMING_UPDATE_STALLED	BIT(23)
+
+#define EMC_MODE_SET_DLL_RESET			BIT(8)
+#define EMC_MODE_SET_LONG_CNT			BIT(26)
+
+#define EMC_SELF_REF_CMD_ENABLED		BIT(0)
+
+#define DRAM_DEV_SEL_ALL			(0 << 30)
+#define DRAM_DEV_SEL_0				(2 << 30)
+#define DRAM_DEV_SEL_1				(1 << 30)
+#define DRAM_BROADCAST(num) \
+	((num) > 1 ? DRAM_DEV_SEL_ALL : DRAM_DEV_SEL_0)
+
+#define EMC_ZQ_CAL_CMD				BIT(0)
+#define EMC_ZQ_CAL_LONG				BIT(4)
+#define EMC_ZQ_CAL_LONG_CMD_DEV0 \
+	(DRAM_DEV_SEL_0 | EMC_ZQ_CAL_LONG | EMC_ZQ_CAL_CMD)
+#define EMC_ZQ_CAL_LONG_CMD_DEV1 \
+	(DRAM_DEV_SEL_1 | EMC_ZQ_CAL_LONG | EMC_ZQ_CAL_CMD)
+
+#define EMC_DBG_READ_MUX_ASSEMBLY		BIT(0)
+#define EMC_DBG_WRITE_MUX_ACTIVE		BIT(1)
+#define EMC_DBG_FORCE_UPDATE			BIT(2)
+#define EMC_DBG_CFG_PRIORITY			BIT(24)
+
+#define EMC_CFG5_QUSE_MODE_SHIFT		13
+#define EMC_CFG5_QUSE_MODE_MASK			(7 << EMC_CFG5_QUSE_MODE_SHIFT)
+
+#define EMC_CFG5_QUSE_MODE_INTERNAL_LPBK	2
+#define EMC_CFG5_QUSE_MODE_PULSE_INTERN		3
+
+#define EMC_SEL_DPD_CTRL_QUSE_DPD_ENABLE	BIT(9)
+
+#define EMC_XM2COMPPADCTRL_VREF_CAL_ENABLE	BIT(10)
+
+#define EMC_XM2QUSEPADCTRL_IVREF_ENABLE		BIT(4)
+
+#define EMC_XM2DQSPADCTRL2_VREF_ENABLE		BIT(5)
+#define EMC_XM2DQSPADCTRL3_VREF_ENABLE		BIT(5)
+
+#define EMC_AUTO_CAL_STATUS_ACTIVE		BIT(31)
+
+#define	EMC_FBIO_CFG5_DRAM_TYPE_MASK		0x3
+
+#define EMC_MRS_WAIT_CNT_SHORT_WAIT_MASK	0x3ff
+#define EMC_MRS_WAIT_CNT_LONG_WAIT_SHIFT	16
+#define EMC_MRS_WAIT_CNT_LONG_WAIT_MASK \
+	(0x3ff << EMC_MRS_WAIT_CNT_LONG_WAIT_SHIFT)
+
+#define EMC_REFCTRL_DEV_SEL_MASK		0x3
+#define EMC_REFCTRL_ENABLE			BIT(31)
+#define EMC_REFCTRL_ENABLE_ALL(num) \
+	(((num) > 1 ? 0 : 2) | EMC_REFCTRL_ENABLE)
+#define EMC_REFCTRL_DISABLE_ALL(num)		((num) > 1 ? 0 : 2)
+
+#define EMC_CFG_PERIODIC_QRST			BIT(21)
+#define EMC_CFG_DYN_SREF_ENABLE			BIT(28)
+
+#define EMC_CLKCHANGE_REQ_ENABLE		BIT(0)
+#define EMC_CLKCHANGE_PD_ENABLE			BIT(1)
+#define EMC_CLKCHANGE_SR_ENABLE			BIT(2)
+
+#define EMC_TIMING_UPDATE			BIT(0)
+
+#define EMC_REFRESH_OVERFLOW_INT		BIT(3)
+#define EMC_CLKCHANGE_COMPLETE_INT		BIT(4)
+
+enum emc_dram_type {
+	DRAM_TYPE_DDR3,
+	DRAM_TYPE_DDR1,
+	DRAM_TYPE_LPDDR2,
+	DRAM_TYPE_DDR2,
+};
+
+enum emc_dll_change {
+	DLL_CHANGE_NONE,
+	DLL_CHANGE_ON,
+	DLL_CHANGE_OFF
+};
+
+static const u16 emc_timing_registers[] = {
+	[0] = EMC_RC,
+	[1] = EMC_RFC,
+	[2] = EMC_RAS,
+	[3] = EMC_RP,
+	[4] = EMC_R2W,
+	[5] = EMC_W2R,
+	[6] = EMC_R2P,
+	[7] = EMC_W2P,
+	[8] = EMC_RD_RCD,
+	[9] = EMC_WR_RCD,
+	[10] = EMC_RRD,
+	[11] = EMC_REXT,
+	[12] = EMC_WEXT,
+	[13] = EMC_WDV,
+	[14] = EMC_QUSE,
+	[15] = EMC_QRST,
+	[16] = EMC_QSAFE,
+	[17] = EMC_RDV,
+	[18] = EMC_REFRESH,
+	[19] = EMC_BURST_REFRESH_NUM,
+	[20] = EMC_PRE_REFRESH_REQ_CNT,
+	[21] = EMC_PDEX2WR,
+	[22] = EMC_PDEX2RD,
+	[23] = EMC_PCHG2PDEN,
+	[24] = EMC_ACT2PDEN,
+	[25] = EMC_AR2PDEN,
+	[26] = EMC_RW2PDEN,
+	[27] = EMC_TXSR,
+	[28] = EMC_TXSRDLL,
+	[29] = EMC_TCKE,
+	[30] = EMC_TFAW,
+	[31] = EMC_TRPAB,
+	[32] = EMC_TCLKSTABLE,
+	[33] = EMC_TCLKSTOP,
+	[34] = EMC_TREFBW,
+	[35] = EMC_QUSE_EXTRA,
+	[36] = EMC_FBIO_CFG6,
+	[37] = EMC_ODT_WRITE,
+	[38] = EMC_ODT_READ,
+	[39] = EMC_FBIO_CFG5,
+	[40] = EMC_CFG_DIG_DLL,
+	[41] = EMC_CFG_DIG_DLL_PERIOD,
+	[42] = EMC_DLL_XFORM_DQS0,
+	[43] = EMC_DLL_XFORM_DQS1,
+	[44] = EMC_DLL_XFORM_DQS2,
+	[45] = EMC_DLL_XFORM_DQS3,
+	[46] = EMC_DLL_XFORM_DQS4,
+	[47] = EMC_DLL_XFORM_DQS5,
+	[48] = EMC_DLL_XFORM_DQS6,
+	[49] = EMC_DLL_XFORM_DQS7,
+	[50] = EMC_DLL_XFORM_QUSE0,
+	[51] = EMC_DLL_XFORM_QUSE1,
+	[52] = EMC_DLL_XFORM_QUSE2,
+	[53] = EMC_DLL_XFORM_QUSE3,
+	[54] = EMC_DLL_XFORM_QUSE4,
+	[55] = EMC_DLL_XFORM_QUSE5,
+	[56] = EMC_DLL_XFORM_QUSE6,
+	[57] = EMC_DLL_XFORM_QUSE7,
+	[58] = EMC_DLI_TRIM_TXDQS0,
+	[59] = EMC_DLI_TRIM_TXDQS1,
+	[60] = EMC_DLI_TRIM_TXDQS2,
+	[61] = EMC_DLI_TRIM_TXDQS3,
+	[62] = EMC_DLI_TRIM_TXDQS4,
+	[63] = EMC_DLI_TRIM_TXDQS5,
+	[64] = EMC_DLI_TRIM_TXDQS6,
+	[65] = EMC_DLI_TRIM_TXDQS7,
+	[66] = EMC_DLL_XFORM_DQ0,
+	[67] = EMC_DLL_XFORM_DQ1,
+	[68] = EMC_DLL_XFORM_DQ2,
+	[69] = EMC_DLL_XFORM_DQ3,
+	[70] = EMC_XM2CMDPADCTRL,
+	[71] = EMC_XM2DQSPADCTRL2,
+	[72] = EMC_XM2DQPADCTRL2,
+	[73] = EMC_XM2CLKPADCTRL,
+	[74] = EMC_XM2COMPPADCTRL,
+	[75] = EMC_XM2VTTGENPADCTRL,
+	[76] = EMC_XM2VTTGENPADCTRL2,
+	[77] = EMC_XM2QUSEPADCTRL,
+	[78] = EMC_XM2DQSPADCTRL3,
+	[79] = EMC_CTT_TERM_CTRL,
+	[80] = EMC_ZCAL_INTERVAL,
+	[81] = EMC_ZCAL_WAIT_CNT,
+	[82] = EMC_MRS_WAIT_CNT,
+	[83] = EMC_AUTO_CAL_CONFIG,
+	[84] = EMC_CTT,
+	[85] = EMC_CTT_DURATION,
+	[86] = EMC_DYN_SELF_REF_CONTROL,
+	[87] = EMC_FBIO_SPARE,
+	[88] = EMC_CFG_RSV,
+};
+
+struct emc_timing {
+	unsigned long rate;
+
+	u32 data[ARRAY_SIZE(emc_timing_registers)];
+
+	u32 emc_auto_cal_interval;
+	u32 emc_mode_1;
+	u32 emc_mode_2;
+	u32 emc_mode_reset;
+	u32 emc_zcal_cnt_long;
+	bool emc_cfg_periodic_qrst;
+	bool emc_cfg_dyn_self_ref;
+};
+
+struct tegra_emc {
+	struct device *dev;
+	struct tegra_mc *mc;
+	struct completion clk_handshake_complete;
+	struct notifier_block clk_nb;
+	struct clk *clk;
+	void __iomem *regs;
+	unsigned int irq;
+
+	struct emc_timing *timings;
+	unsigned int num_timings;
+
+	u32 mc_override;
+	u32 emc_cfg;
+
+	u32 emc_mode_1;
+	u32 emc_mode_2;
+	u32 emc_mode_reset;
+
+	bool vref_cal_toggle : 1;
+	bool zcal_long : 1;
+	bool dll_on : 1;
+	bool prepared : 1;
+	bool bad_state : 1;
+};
+
+static irqreturn_t tegra_emc_isr(int irq, void *data)
+{
+	struct tegra_emc *emc = data;
+	u32 intmask = EMC_REFRESH_OVERFLOW_INT | EMC_CLKCHANGE_COMPLETE_INT;
+	u32 status;
+
+	status = readl_relaxed(emc->regs + EMC_INTSTATUS) & intmask;
+	if (!status)
+		return IRQ_NONE;
+
+	/* notify about EMC-CAR handshake completion */
+	if (status & EMC_CLKCHANGE_COMPLETE_INT)
+		complete(&emc->clk_handshake_complete);
+
+	/* notify about HW problem */
+	if (status & EMC_REFRESH_OVERFLOW_INT)
+		dev_err_ratelimited(emc->dev,
+				    "refresh request overflow timeout\n");
+
+	/* clear interrupts */
+	writel_relaxed(status, emc->regs + EMC_INTSTATUS);
+
+	return IRQ_HANDLED;
+}
+
+static struct emc_timing *emc_find_timing(struct tegra_emc *emc,
+					  unsigned long rate)
+{
+	struct emc_timing *timing = NULL;
+	unsigned int i;
+
+	for (i = 0; i < emc->num_timings; i++) {
+		if (emc->timings[i].rate >= rate) {
+			timing = &emc->timings[i];
+			break;
+		}
+	}
+
+	if (!timing) {
+		dev_err(emc->dev, "no timing for rate %lu\n", rate);
+		return NULL;
+	}
+
+	return timing;
+}
+
+static bool emc_dqs_preset(struct tegra_emc *emc, struct emc_timing *timing,
+			   bool *schmitt_to_vref)
+{
+	bool preset = false;
+	u32 val;
+
+	if (timing->data[71] & EMC_XM2DQSPADCTRL2_VREF_ENABLE) {
+		val = readl_relaxed(emc->regs + EMC_XM2DQSPADCTRL2);
+
+		if (!(val & EMC_XM2DQSPADCTRL2_VREF_ENABLE)) {
+			val |= EMC_XM2DQSPADCTRL2_VREF_ENABLE;
+			writel_relaxed(val, emc->regs + EMC_XM2DQSPADCTRL2);
+
+			preset = true;
+		}
+	}
+
+	if (timing->data[78] & EMC_XM2DQSPADCTRL3_VREF_ENABLE) {
+		val = readl_relaxed(emc->regs + EMC_XM2DQSPADCTRL3);
+
+		if (!(val & EMC_XM2DQSPADCTRL3_VREF_ENABLE)) {
+			val |= EMC_XM2DQSPADCTRL3_VREF_ENABLE;
+			writel_relaxed(val, emc->regs + EMC_XM2DQSPADCTRL3);
+
+			preset = true;
+		}
+	}
+
+	if (timing->data[77] & EMC_XM2QUSEPADCTRL_IVREF_ENABLE) {
+		val = readl_relaxed(emc->regs + EMC_XM2QUSEPADCTRL);
+
+		if (!(val & EMC_XM2QUSEPADCTRL_IVREF_ENABLE)) {
+			val |= EMC_XM2QUSEPADCTRL_IVREF_ENABLE;
+			writel_relaxed(val, emc->regs + EMC_XM2QUSEPADCTRL);
+
+			*schmitt_to_vref = true;
+			preset = true;
+		}
+	}
+
+	return preset;
+}
+
+static int emc_seq_update_timing(struct tegra_emc *emc)
+{
+	u32 val;
+	int err;
+
+	writel_relaxed(EMC_TIMING_UPDATE, emc->regs + EMC_TIMING_CONTROL);
+
+	err = readl_relaxed_poll_timeout_atomic(emc->regs + EMC_STATUS, val,
+				!(val & EMC_STATUS_TIMING_UPDATE_STALLED),
+				1, 200);
+	if (err) {
+		dev_err(emc->dev, "failed to update timing: %d\n", err);
+		return err;
+	}
+
+	return 0;
+}
+
+static int emc_prepare_mc_clk_cfg(struct tegra_emc *emc, unsigned long rate)
+{
+	struct tegra_mc *mc = emc->mc;
+	unsigned int misc0_index = 16;
+	unsigned int i;
+	bool same;
+
+	for (i = 0; i < mc->num_timings; i++) {
+		if (mc->timings[i].rate != rate)
+			continue;
+
+		if (mc->timings[i].emem_data[misc0_index] & BIT(27))
+			same = true;
+		else
+			same = false;
+
+		return tegra20_clk_prepare_emc_mc_same_freq(emc->clk, same);
+	}
+
+	return -EINVAL;
+}
+
+static int emc_prepare_timing_change(struct tegra_emc *emc, unsigned long rate)
+{
+	struct emc_timing *timing = emc_find_timing(emc, rate);
+	enum emc_dll_change dll_change;
+	enum emc_dram_type dram_type;
+	bool schmitt_to_vref = false;
+	unsigned int pre_wait = 0;
+	bool qrst_used = false;
+	unsigned int dram_num;
+	unsigned int i;
+	u32 fbio_cfg5;
+	u32 emc_dbg;
+	u32 val;
+	int err;
+
+	if (!timing || emc->bad_state)
+		return -EINVAL;
+
+	dev_dbg(emc->dev, "%s: using timing rate %lu for requested rate %lu\n",
+		__func__, timing->rate, rate);
+
+	emc->bad_state = true;
+
+	err = emc_prepare_mc_clk_cfg(emc, rate);
+	if (err) {
+		dev_err(emc->dev, "mc clock preparation failed: %d\n", err);
+		return err;
+	}
+
+	emc->vref_cal_toggle = false;
+	emc->mc_override = mc_readl(emc->mc, MC_EMEM_ARB_OVERRIDE);
+	emc->emc_cfg = readl_relaxed(emc->regs + EMC_CFG);
+	emc_dbg = readl_relaxed(emc->regs + EMC_DBG);
+
+	if (emc->dll_on == !!(timing->emc_mode_1 & 0x1))
+		dll_change = DLL_CHANGE_NONE;
+	else if (timing->emc_mode_1 & 0x1)
+		dll_change = DLL_CHANGE_ON;
+	else
+		dll_change = DLL_CHANGE_OFF;
+
+	emc->dll_on = !!(timing->emc_mode_1 & 0x1);
+
+	if (timing->data[80] && !readl_relaxed(emc->regs + EMC_ZCAL_INTERVAL))
+		emc->zcal_long = true;
+	else
+		emc->zcal_long = false;
+
+	fbio_cfg5 = readl_relaxed(emc->regs + EMC_FBIO_CFG5);
+	dram_type = fbio_cfg5 & EMC_FBIO_CFG5_DRAM_TYPE_MASK;
+
+	dram_num = tegra_mc_get_emem_device_count(emc->mc);
+
+	/* disable dynamic self-refresh */
+	if (emc->emc_cfg & EMC_CFG_DYN_SREF_ENABLE) {
+		emc->emc_cfg &= ~EMC_CFG_DYN_SREF_ENABLE;
+		writel_relaxed(emc->emc_cfg, emc->regs + EMC_CFG);
+
+		pre_wait = 5;
+	}
+
+	/* update MC arbiter settings */
+	val = mc_readl(emc->mc, MC_EMEM_ARB_OUTSTANDING_REQ);
+	if (!(val & MC_EMEM_ARB_OUTSTANDING_REQ_HOLDOFF_OVERRIDE) ||
+	    ((val & MC_EMEM_ARB_OUTSTANDING_REQ_MAX_MASK) > 0x50)) {
+
+		val = MC_EMEM_ARB_OUTSTANDING_REQ_LIMIT_ENABLE |
+		      MC_EMEM_ARB_OUTSTANDING_REQ_HOLDOFF_OVERRIDE | 0x50;
+		mc_writel(emc->mc, val, MC_EMEM_ARB_OUTSTANDING_REQ);
+		mc_writel(emc->mc, MC_TIMING_UPDATE, MC_TIMING_CONTROL);
+	}
+
+	if (emc->mc_override & MC_EMEM_ARB_OVERRIDE_EACK_MASK)
+		mc_writel(emc->mc,
+			  emc->mc_override & ~MC_EMEM_ARB_OVERRIDE_EACK_MASK,
+			  MC_EMEM_ARB_OVERRIDE);
+
+	/* check DQ/DQS VREF delay */
+	if (emc_dqs_preset(emc, timing, &schmitt_to_vref)) {
+		if (pre_wait < 3)
+			pre_wait = 3;
+	}
+
+	if (pre_wait) {
+		err = emc_seq_update_timing(emc);
+		if (err)
+			return err;
+
+		udelay(pre_wait);
+	}
+
+	/* disable auto-calibration if VREF mode is switching */
+	if (timing->emc_auto_cal_interval) {
+		val = readl_relaxed(emc->regs + EMC_XM2COMPPADCTRL);
+		val ^= timing->data[74];
+
+		if (val & EMC_XM2COMPPADCTRL_VREF_CAL_ENABLE) {
+			writel_relaxed(0, emc->regs + EMC_AUTO_CAL_INTERVAL);
+
+			err = readl_relaxed_poll_timeout_atomic(
+				emc->regs + EMC_AUTO_CAL_STATUS, val,
+				!(val & EMC_AUTO_CAL_STATUS_ACTIVE), 1, 300);
+			if (err) {
+				dev_err(emc->dev,
+					"failed to disable auto-cal: %d\n",
+					err);
+				return err;
+			}
+
+			emc->vref_cal_toggle = true;
+		}
+	}
+
+	/* program shadow registers */
+	for (i = 0; i < ARRAY_SIZE(timing->data); i++) {
+		/* EMC_XM2CLKPADCTRL should be programmed separately */
+		if (i != 73)
+			writel_relaxed(timing->data[i],
+				       emc->regs + emc_timing_registers[i]);
+	}
+
+	err = tegra_mc_write_emem_configuration(emc->mc, timing->rate);
+	if (err)
+		return err;
+
+	/* DDR3: predict MRS long wait count */
+	if (dram_type == DRAM_TYPE_DDR3 && dll_change == DLL_CHANGE_ON) {
+		u32 cnt = 512;
+
+		if (emc->zcal_long)
+			cnt -= dram_num * 256;
+
+		val = timing->data[82] & EMC_MRS_WAIT_CNT_SHORT_WAIT_MASK;
+		if (cnt < val)
+			cnt = val;
+
+		val = timing->data[82] & ~EMC_MRS_WAIT_CNT_LONG_WAIT_MASK;
+		val |= (cnt << EMC_MRS_WAIT_CNT_LONG_WAIT_SHIFT) &
+			EMC_MRS_WAIT_CNT_LONG_WAIT_MASK;
+
+		writel_relaxed(val, emc->regs + EMC_MRS_WAIT_CNT);
+	}
+
+	/* disable interrupt since read access is prohibited after stalling */
+	disable_irq(emc->irq);
+
+	/* this read also completes the writes */
+	val = readl_relaxed(emc->regs + EMC_SEL_DPD_CTRL);
+
+	if (!(val & EMC_SEL_DPD_CTRL_QUSE_DPD_ENABLE) && schmitt_to_vref) {
+		u32 cur_mode, new_mode;
+
+		cur_mode = fbio_cfg5 & EMC_CFG5_QUSE_MODE_MASK;
+		cur_mode >>= EMC_CFG5_QUSE_MODE_SHIFT;
+
+		new_mode = timing->data[39] & EMC_CFG5_QUSE_MODE_MASK;
+		new_mode >>= EMC_CFG5_QUSE_MODE_SHIFT;
+
+		if ((cur_mode != EMC_CFG5_QUSE_MODE_PULSE_INTERN &&
+		     cur_mode != EMC_CFG5_QUSE_MODE_INTERNAL_LPBK) ||
+		    (new_mode != EMC_CFG5_QUSE_MODE_PULSE_INTERN &&
+		     new_mode != EMC_CFG5_QUSE_MODE_INTERNAL_LPBK))
+			qrst_used = true;
+	}
+
+	/* flow control marker 1 */
+	writel_relaxed(0x1, emc->regs + EMC_STALL_THEN_EXE_BEFORE_CLKCHANGE);
+
+	/* enable periodic reset */
+	if (qrst_used) {
+		writel_relaxed(emc_dbg | EMC_DBG_WRITE_MUX_ACTIVE,
+			       emc->regs + EMC_DBG);
+		writel_relaxed(emc->emc_cfg | EMC_CFG_PERIODIC_QRST,
+			       emc->regs + EMC_CFG);
+		writel_relaxed(emc_dbg, emc->regs + EMC_DBG);
+	}
+
+	/* disable auto-refresh to save time after clock change */
+	writel_relaxed(EMC_REFCTRL_DISABLE_ALL(dram_num),
+		       emc->regs + EMC_REFCTRL);
+
+	/* turn off DLL and enter self-refresh on DDR3 */
+	if (dram_type == DRAM_TYPE_DDR3) {
+		if (dll_change == DLL_CHANGE_OFF)
+			writel_relaxed(timing->emc_mode_1,
+				       emc->regs + EMC_EMRS);
+
+		writel_relaxed(DRAM_BROADCAST(dram_num) |
+			       EMC_SELF_REF_CMD_ENABLED,
+			       emc->regs + EMC_SELF_REF);
+	}
+
+	/* flow control marker 2 */
+	writel_relaxed(0x1, emc->regs + EMC_STALL_THEN_EXE_AFTER_CLKCHANGE);
+
+	/* enable write-active MUX, update unshadowed pad control */
+	writel_relaxed(emc_dbg | EMC_DBG_WRITE_MUX_ACTIVE, emc->regs + EMC_DBG);
+	writel_relaxed(timing->data[73], emc->regs + EMC_XM2CLKPADCTRL);
+
+	/* restore periodic QRST and disable write-active MUX */
+	val = !!(emc->emc_cfg & EMC_CFG_PERIODIC_QRST);
+	if (qrst_used || timing->emc_cfg_periodic_qrst != val) {
+		if (timing->emc_cfg_periodic_qrst)
+			emc->emc_cfg |= EMC_CFG_PERIODIC_QRST;
+		else
+			emc->emc_cfg &= ~EMC_CFG_PERIODIC_QRST;
+
+		writel_relaxed(emc->emc_cfg, emc->regs + EMC_CFG);
+	}
+	writel_relaxed(emc_dbg, emc->regs + EMC_DBG);
+
+	/* exit self-refresh on DDR3 */
+	if (dram_type == DRAM_TYPE_DDR3)
+		writel_relaxed(DRAM_BROADCAST(dram_num),
+			       emc->regs + EMC_SELF_REF);
+
+	/* set DRAM-mode registers */
+	if (dram_type == DRAM_TYPE_DDR3) {
+		if (timing->emc_mode_1 != emc->emc_mode_1)
+			writel_relaxed(timing->emc_mode_1,
+				       emc->regs + EMC_EMRS);
+
+		if (timing->emc_mode_2 != emc->emc_mode_2)
+			writel_relaxed(timing->emc_mode_2,
+				       emc->regs + EMC_EMRS);
+
+		if (timing->emc_mode_reset != emc->emc_mode_reset ||
+		    dll_change == DLL_CHANGE_ON) {
+			val = timing->emc_mode_reset;
+			if (dll_change == DLL_CHANGE_ON) {
+				val |= EMC_MODE_SET_DLL_RESET;
+				val |= EMC_MODE_SET_LONG_CNT;
+			} else {
+				val &= ~EMC_MODE_SET_DLL_RESET;
+			}
+			writel_relaxed(val, emc->regs + EMC_MRS);
+		}
+	} else {
+		if (timing->emc_mode_2 != emc->emc_mode_2)
+			writel_relaxed(timing->emc_mode_2,
+				       emc->regs + EMC_MRW);
+
+		if (timing->emc_mode_1 != emc->emc_mode_1)
+			writel_relaxed(timing->emc_mode_1,
+				       emc->regs + EMC_MRW);
+	}
+
+	emc->emc_mode_1 = timing->emc_mode_1;
+	emc->emc_mode_2 = timing->emc_mode_2;
+	emc->emc_mode_reset = timing->emc_mode_reset;
+
+	/* issue ZCAL command if turning ZCAL on */
+	if (emc->zcal_long) {
+		writel_relaxed(EMC_ZQ_CAL_LONG_CMD_DEV0,
+			       emc->regs + EMC_ZQ_CAL);
+
+		if (dram_num > 1)
+			writel_relaxed(EMC_ZQ_CAL_LONG_CMD_DEV1,
+				       emc->regs + EMC_ZQ_CAL);
+	}
+
+	/* re-enable auto-refresh */
+	writel_relaxed(EMC_REFCTRL_ENABLE_ALL(dram_num),
+		       emc->regs + EMC_REFCTRL);
+
+	/* flow control marker 3 */
+	writel_relaxed(0x1, emc->regs + EMC_UNSTALL_RW_AFTER_CLKCHANGE);
+
+	reinit_completion(&emc->clk_handshake_complete);
+
+	/* interrupt can be re-enabled now */
+	enable_irq(emc->irq);
+
+	emc->bad_state = false;
+	emc->prepared = true;
+
+	return 0;
+}
+
+static int emc_complete_timing_change(struct tegra_emc *emc,
+				      unsigned long rate)
+{
+	struct emc_timing *timing = emc_find_timing(emc, rate);
+	unsigned long timeout;
+	int ret;
+
+	timeout = wait_for_completion_timeout(&emc->clk_handshake_complete,
+					      msecs_to_jiffies(100));
+	if (timeout == 0) {
+		dev_err(emc->dev, "emc-car handshake failed\n");
+		emc->bad_state = true;
+		return -EIO;
+	}
+
+	/* restore auto-calibration */
+	if (emc->vref_cal_toggle)
+		writel_relaxed(timing->emc_auto_cal_interval,
+			       emc->regs + EMC_AUTO_CAL_INTERVAL);
+
+	/* restore dynamic self-refresh */
+	if (timing->emc_cfg_dyn_self_ref) {
+		emc->emc_cfg |= EMC_CFG_DYN_SREF_ENABLE;
+		writel_relaxed(emc->emc_cfg, emc->regs + EMC_CFG);
+	}
+
+	/* set number of clocks to wait after each ZQ command */
+	if (emc->zcal_long)
+		writel_relaxed(timing->emc_zcal_cnt_long,
+			       emc->regs + EMC_ZCAL_WAIT_CNT);
+
+	udelay(2);
+	/* update restored timing */
+	ret = emc_seq_update_timing(emc);
+	if (ret)
+		emc->bad_state = true;
+
+	/* restore early ACK */
+	mc_writel(emc->mc, emc->mc_override, MC_EMEM_ARB_OVERRIDE);
+
+	emc->prepared = false;
+
+	return ret;
+}
+
+static int emc_unprepare_timing_change(struct tegra_emc *emc,
+				       unsigned long rate)
+{
+	if (emc->prepared && !emc->bad_state) {
+		/* shouldn't ever happen in practice */
+		dev_err(emc->dev, "timing configuration can't be reverted\n");
+		emc->bad_state = true;
+	}
+
+	return 0;
+}
+
+static int emc_clk_change_notify(struct notifier_block *nb,
+				 unsigned long msg, void *data)
+{
+	struct tegra_emc *emc = container_of(nb, struct tegra_emc, clk_nb);
+	struct clk_notifier_data *cnd = data;
+	int err;
+
+	switch (msg) {
+	case PRE_RATE_CHANGE:
+		err = emc_prepare_timing_change(emc, cnd->new_rate);
+		break;
+
+	case ABORT_RATE_CHANGE:
+		err = emc_unprepare_timing_change(emc, cnd->old_rate);
+		break;
+
+	case POST_RATE_CHANGE:
+		err = emc_complete_timing_change(emc, cnd->new_rate);
+		break;
+
+	default:
+		return NOTIFY_DONE;
+	}
+
+	return notifier_from_errno(err);
+}
+
+static int load_one_timing_from_dt(struct tegra_emc *emc,
+				   struct emc_timing *timing,
+				   struct device_node *node)
+{
+	u32 value;
+	int err;
+
+	err = of_property_read_u32(node, "clock-frequency", &value);
+	if (err) {
+		dev_err(emc->dev, "timing %pOF: failed to read rate: %d\n",
+			node, err);
+		return err;
+	}
+
+	timing->rate = value;
+
+	err = of_property_read_u32_array(node, "nvidia,emc-configuration",
+					 timing->data,
+					 ARRAY_SIZE(emc_timing_registers));
+	if (err) {
+		dev_err(emc->dev,
+			"timing %pOF: failed to read emc timing data: %d\n",
+			node, err);
+		return err;
+	}
+
+#define EMC_READ_BOOL(prop, dtprop) \
+	timing->prop = of_property_read_bool(node, dtprop);
+
+#define EMC_READ_U32(prop, dtprop) \
+	err = of_property_read_u32(node, dtprop, &timing->prop); \
+	if (err) { \
+		dev_err(emc->dev, \
+			"timing %pOFn: failed to read " #prop ": %d\n", \
+			node, err); \
+		return err; \
+	}
+
+	EMC_READ_U32(emc_auto_cal_interval, "nvidia,emc-auto-cal-interval")
+	EMC_READ_U32(emc_mode_1, "nvidia,emc-mode-1")
+	EMC_READ_U32(emc_mode_2, "nvidia,emc-mode-2")
+	EMC_READ_U32(emc_mode_reset, "nvidia,emc-mode-reset")
+	EMC_READ_U32(emc_zcal_cnt_long, "nvidia,emc-zcal-cnt-long")
+	EMC_READ_BOOL(emc_cfg_dyn_self_ref, "nvidia,emc-cfg-dyn-self-ref")
+	EMC_READ_BOOL(emc_cfg_periodic_qrst, "nvidia,emc-cfg-periodic-qrst")
+
+#undef EMC_READ_U32
+#undef EMC_READ_BOOL
+
+	dev_dbg(emc->dev, "%s: %pOF: rate %lu\n", __func__, node, timing->rate);
+
+	return 0;
+}
+
+static int cmp_timings(const void *_a, const void *_b)
+{
+	const struct emc_timing *a = _a;
+	const struct emc_timing *b = _b;
+
+	if (a->rate < b->rate)
+		return -1;
+
+	if (a->rate > b->rate)
+		return 1;
+
+	return 0;
+}
+
+static int emc_check_mc_timings(struct tegra_emc *emc)
+{
+	struct tegra_mc *mc = emc->mc;
+	unsigned int i;
+
+	if (emc->num_timings != mc->num_timings) {
+		dev_err(emc->dev, "emc/mc timings number mismatch: %u %u\n",
+			emc->num_timings, mc->num_timings);
+		return -EINVAL;
+	}
+
+	for (i = 0; i < mc->num_timings; i++) {
+		if (emc->timings[i].rate != mc->timings[i].rate) {
+			dev_err(emc->dev,
+				"emc/mc timing rate mismatch: %lu %lu\n",
+				emc->timings[i].rate, mc->timings[i].rate);
+			return -EINVAL;
+		}
+	}
+
+	return 0;
+}
+
+static int emc_load_timings_from_dt(struct tegra_emc *emc,
+				    struct device_node *node)
+{
+	struct device_node *child;
+	struct emc_timing *timing;
+	int child_count;
+	int err;
+
+	child_count = of_get_child_count(node);
+	if (!child_count) {
+		dev_err(emc->dev, "no memory timings in: %pOF\n", node);
+		return -EINVAL;
+	}
+
+	emc->timings = devm_kcalloc(emc->dev, child_count, sizeof(*timing),
+				    GFP_KERNEL);
+	if (!emc->timings)
+		return -ENOMEM;
+
+	emc->num_timings = child_count;
+	timing = emc->timings;
+
+	for_each_child_of_node(node, child) {
+		err = load_one_timing_from_dt(emc, timing++, child);
+		if (err) {
+			of_node_put(child);
+			return err;
+		}
+	}
+
+	sort(emc->timings, emc->num_timings, sizeof(*timing), cmp_timings,
+	     NULL);
+
+	err = emc_check_mc_timings(emc);
+	if (err)
+		return err;
+
+	dev_info(emc->dev,
+		 "got %u timings for RAM code %u (min %luMHz max %luMHz)\n",
+		 emc->num_timings,
+		 tegra_read_ram_code(),
+		 emc->timings[0].rate / 1000000,
+		 emc->timings[emc->num_timings - 1].rate / 1000000);
+
+	return 0;
+}
+
+static struct device_node *emc_find_node_by_ram_code(struct device *dev)
+{
+	struct device_node *np;
+	u32 value, ram_code;
+	int err;
+
+	ram_code = tegra_read_ram_code();
+
+	for_each_child_of_node(dev->of_node, np) {
+		err = of_property_read_u32(np, "nvidia,ram-code", &value);
+		if (err || value != ram_code)
+			continue;
+
+		return np;
+	}
+
+	dev_err(dev, "no memory timings for RAM code %u found in device-tree\n",
+		ram_code);
+
+	return NULL;
+}
+
+static int emc_setup_hw(struct tegra_emc *emc)
+{
+	u32 intmask = EMC_REFRESH_OVERFLOW_INT | EMC_CLKCHANGE_COMPLETE_INT;
+	u32 fbio_cfg5, emc_cfg, emc_dbg;
+	enum emc_dram_type dram_type;
+
+	fbio_cfg5 = readl_relaxed(emc->regs + EMC_FBIO_CFG5);
+	dram_type = fbio_cfg5 & EMC_FBIO_CFG5_DRAM_TYPE_MASK;
+
+	emc_cfg = readl_relaxed(emc->regs + EMC_CFG_2);
+
+	/* enable EMC and CAR to handshake on PLL divider/source changes */
+	emc_cfg |= EMC_CLKCHANGE_REQ_ENABLE;
+
+	/* configure clock change mode accordingly to DRAM type */
+	switch (dram_type) {
+	case DRAM_TYPE_LPDDR2:
+		emc_cfg |= EMC_CLKCHANGE_PD_ENABLE;
+		emc_cfg &= ~EMC_CLKCHANGE_SR_ENABLE;
+		break;
+
+	default:
+		emc_cfg &= ~EMC_CLKCHANGE_SR_ENABLE;
+		emc_cfg &= ~EMC_CLKCHANGE_PD_ENABLE;
+		break;
+	}
+
+	writel_relaxed(emc_cfg, emc->regs + EMC_CFG_2);
+
+	/* initialize interrupt */
+	writel_relaxed(intmask, emc->regs + EMC_INTMASK);
+	writel_relaxed(0xffffffff, emc->regs + EMC_INTSTATUS);
+
+	/* ensure that unwanted debug features are disabled */
+	emc_dbg = readl_relaxed(emc->regs + EMC_DBG);
+	emc_dbg |= EMC_DBG_CFG_PRIORITY;
+	emc_dbg &= ~EMC_DBG_READ_MUX_ASSEMBLY;
+	emc_dbg &= ~EMC_DBG_WRITE_MUX_ACTIVE;
+	emc_dbg &= ~EMC_DBG_FORCE_UPDATE;
+	writel_relaxed(emc_dbg, emc->regs + EMC_DBG);
+
+	return 0;
+}
+
+static long emc_round_rate(unsigned long rate,
+			   unsigned long min_rate,
+			   unsigned long max_rate,
+			   void *arg)
+{
+	struct emc_timing *timing = NULL;
+	struct tegra_emc *emc = arg;
+	unsigned int i;
+
+	min_rate = min(min_rate, emc->timings[emc->num_timings - 1].rate);
+
+	for (i = 0; i < emc->num_timings; i++) {
+		if (emc->timings[i].rate < rate && i != emc->num_timings - 1)
+			continue;
+
+		if (emc->timings[i].rate > max_rate) {
+			i = max(i, 1u) - 1;
+
+			if (emc->timings[i].rate < min_rate)
+				break;
+		}
+
+		if (emc->timings[i].rate < min_rate)
+			continue;
+
+		timing = &emc->timings[i];
+		break;
+	}
+
+	if (!timing) {
+		dev_err(emc->dev, "no timing for rate %lu min %lu max %lu\n",
+			rate, min_rate, max_rate);
+		return -EINVAL;
+	}
+
+	return timing->rate;
+}
+
+static int tegra_emc_probe(struct platform_device *pdev)
+{
+	struct platform_device *mc;
+	struct device_node *np;
+	struct tegra_emc *emc;
+	int err;
+
+	if (of_get_child_count(pdev->dev.of_node) == 0) {
+		dev_info(&pdev->dev,
+			 "device-tree node doesn't have memory timings\n");
+		return 0;
+	}
+
+	np = of_parse_phandle(pdev->dev.of_node, "nvidia,memory-controller", 0);
+	if (!np) {
+		dev_err(&pdev->dev, "could not get memory controller node\n");
+		return -ENOENT;
+	}
+
+	mc = of_find_device_by_node(np);
+	of_node_put(np);
+	if (!mc)
+		return -ENOENT;
+
+	np = emc_find_node_by_ram_code(&pdev->dev);
+	if (!np)
+		return -EINVAL;
+
+	emc = devm_kzalloc(&pdev->dev, sizeof(*emc), GFP_KERNEL);
+	if (!emc) {
+		of_node_put(np);
+		return -ENOMEM;
+	}
+
+	emc->mc = platform_get_drvdata(mc);
+	if (!emc->mc)
+		return -EPROBE_DEFER;
+
+	init_completion(&emc->clk_handshake_complete);
+	emc->clk_nb.notifier_call = emc_clk_change_notify;
+	emc->dev = &pdev->dev;
+
+	err = emc_load_timings_from_dt(emc, np);
+	of_node_put(np);
+	if (err)
+		return err;
+
+	emc->regs = devm_platform_ioremap_resource(pdev, 0);
+	if (IS_ERR(emc->regs))
+		return PTR_ERR(emc->regs);
+
+	err = emc_setup_hw(emc);
+	if (err)
+		return err;
+
+	err = platform_get_irq(pdev, 0);
+	if (err < 0) {
+		dev_err(&pdev->dev, "interrupt not specified: %d\n", err);
+		return err;
+	}
+	emc->irq = err;
+
+	err = devm_request_irq(&pdev->dev, emc->irq, tegra_emc_isr, 0,
+			       dev_name(&pdev->dev), emc);
+	if (err) {
+		dev_err(&pdev->dev, "failed to request irq: %d\n", err);
+		return err;
+	}
+
+	tegra20_clk_set_emc_round_callback(emc_round_rate, emc);
+
+	emc->clk = devm_clk_get(&pdev->dev, "emc");
+	if (IS_ERR(emc->clk)) {
+		err = PTR_ERR(emc->clk);
+		dev_err(&pdev->dev, "failed to get emc clock: %d\n", err);
+		goto unset_cb;
+	}
+
+	err = clk_notifier_register(emc->clk, &emc->clk_nb);
+	if (err) {
+		dev_err(&pdev->dev, "failed to register clk notifier: %d\n",
+			err);
+		goto unset_cb;
+	}
+
+	platform_set_drvdata(pdev, emc);
+
+	return 0;
+
+unset_cb:
+	tegra20_clk_set_emc_round_callback(NULL, NULL);
+
+	return err;
+}
+
+static int tegra_emc_suspend(struct device *dev)
+{
+	struct tegra_emc *emc = dev_get_drvdata(dev);
+
+	/*
+	 * Suspending in a bad state will hang machine. The "prepared" var
+	 * shall be always false here unless it's a kernel bug that caused
+	 * suspending in a wrong order.
+	 */
+	if (WARN_ON(emc->prepared) || emc->bad_state)
+		return -EINVAL;
+
+	emc->bad_state = true;
+
+	return 0;
+}
+
+static int tegra_emc_resume(struct device *dev)
+{
+	struct tegra_emc *emc = dev_get_drvdata(dev);
+
+	emc_setup_hw(emc);
+	emc->bad_state = false;
+
+	return 0;
+}
+
+static const struct dev_pm_ops tegra_emc_pm_ops = {
+	.suspend = tegra_emc_suspend,
+	.resume = tegra_emc_resume,
+};
+
+static const struct of_device_id tegra_emc_of_match[] = {
+	{ .compatible = "nvidia,tegra30-emc", },
+	{},
+};
+
+static struct platform_driver tegra_emc_driver = {
+	.probe = tegra_emc_probe,
+	.driver = {
+		.name = "tegra30-emc",
+		.of_match_table = tegra_emc_of_match,
+		.pm = &tegra_emc_pm_ops,
+		.suppress_bind_attrs = true,
+	},
+};
+
+static int __init tegra_emc_init(void)
+{
+	return platform_driver_register(&tegra_emc_driver);
+}
+subsys_initcall(tegra_emc_init);
diff --git a/drivers/memory/tegra/tegra30.c b/drivers/memory/tegra/tegra30.c
index 14788fc2f9e8..fcdd812eed80 100644
--- a/drivers/memory/tegra/tegra30.c
+++ b/drivers/memory/tegra/tegra30.c
@@ -10,6 +10,27 @@
 
 #include "mc.h"
 
+static const unsigned long tegra30_mc_emem_regs[] = {
+	MC_EMEM_ARB_CFG,
+	MC_EMEM_ARB_OUTSTANDING_REQ,
+	MC_EMEM_ARB_TIMING_RCD,
+	MC_EMEM_ARB_TIMING_RP,
+	MC_EMEM_ARB_TIMING_RC,
+	MC_EMEM_ARB_TIMING_RAS,
+	MC_EMEM_ARB_TIMING_FAW,
+	MC_EMEM_ARB_TIMING_RRD,
+	MC_EMEM_ARB_TIMING_RAP2PRE,
+	MC_EMEM_ARB_TIMING_WAP2PRE,
+	MC_EMEM_ARB_TIMING_R2R,
+	MC_EMEM_ARB_TIMING_W2W,
+	MC_EMEM_ARB_TIMING_R2W,
+	MC_EMEM_ARB_TIMING_W2R,
+	MC_EMEM_ARB_DA_TURNS,
+	MC_EMEM_ARB_DA_COVERS,
+	MC_EMEM_ARB_MISC0,
+	MC_EMEM_ARB_RING1_THROTTLE,
+};
+
 static const struct tegra_mc_client tegra30_mc_clients[] = {
 	{
 		.id = 0x00,
@@ -931,16 +952,19 @@ static const struct tegra_smmu_swgroup tegra30_swgroups[] = {
 	{ .name = "isp",  .swgroup = TEGRA_SWGROUP_ISP,  .reg = 0x258 },
 };
 
-static const unsigned int tegra30_group_display[] = {
+static const unsigned int tegra30_group_drm[] = {
 	TEGRA_SWGROUP_DC,
 	TEGRA_SWGROUP_DCB,
+	TEGRA_SWGROUP_G2,
+	TEGRA_SWGROUP_NV,
+	TEGRA_SWGROUP_NV2,
 };
 
 static const struct tegra_smmu_group_soc tegra30_groups[] = {
 	{
-		.name = "display",
-		.swgroups = tegra30_group_display,
-		.num_swgroups = ARRAY_SIZE(tegra30_group_display),
+		.name = "drm",
+		.swgroups = tegra30_group_drm,
+		.num_swgroups = ARRAY_SIZE(tegra30_group_drm),
 	},
 };
 
@@ -994,6 +1018,8 @@ const struct tegra_mc_soc tegra30_mc_soc = {
 	.atom_size = 16,
 	.client_id_mask = 0x7f,
 	.smmu = &tegra30_smmu_soc,
+	.emem_regs = tegra30_mc_emem_regs,
+	.num_emem_regs = ARRAY_SIZE(tegra30_mc_emem_regs),
 	.intmask = MC_INT_INVALID_SMMU_PAGE | MC_INT_SECURITY_VIOLATION |
 		   MC_INT_DECERR_EMEM,
 	.reset_ops = &tegra_mc_reset_ops_common,