drm/omap: squash omapdrm sub-modules into one

At the moment we have three different modules: omapdss-base, omapdss,
omapdrm. This setup is finally obsolete, as the last omapdrm specific
panel has been converted to DRM panel.

We can thus remove omapdss-base and omapdss, and just compile everything
into omapdrm.ko.

Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Reviewed-by: Sebastian Reichel <sebastian.reichel@collabora.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20201215104657.802264-51-tomi.valkeinen@ti.com

1 files changed, 118 insertions, 1 deletions

diff --git a/drivers/gpu/drm/omapdrm/Kconfig b/drivers/gpu/drm/omapdrm/Kconfig
index cea3f44ea6d4..e7281da5bc6a 100644
--- a/drivers/gpu/drm/omapdrm/Kconfig
+++ b/drivers/gpu/drm/omapdrm/Kconfig
@@ -5,12 +5,129 @@ config DRM_OMAP
 	depends on ARCH_OMAP2PLUS || ARCH_MULTIPLATFORM
 	select OMAP2_DSS
 	select DRM_KMS_HELPER
+	select VIDEOMODE_HELPERS
+	select HDMI
 	default n
 	help
 	  DRM display driver for OMAP2/3/4 based boards.
 
 if DRM_OMAP
 
-source "drivers/gpu/drm/omapdrm/dss/Kconfig"
+config OMAP2_DSS_DEBUG
+	bool "Debug support"
+	default n
+	help
+	  This enables printing of debug messages. Alternatively, debug messages
+	  can also be enabled by setting CONFIG_DYNAMIC_DEBUG and then setting
+	  appropriate flags in <debugfs>/dynamic_debug/control.
+
+config OMAP2_DSS_DEBUGFS
+	bool "Debugfs filesystem support"
+	depends on DEBUG_FS
+	default n
+	help
+	  This enables debugfs for OMAPDSS at <debugfs>/omapdss. This enables
+	  querying about clock configuration and register configuration of dss,
+	  dispc, dsi, hdmi and rfbi.
+
+config OMAP2_DSS_COLLECT_IRQ_STATS
+	bool "Collect DSS IRQ statistics"
+	depends on OMAP2_DSS_DEBUGFS
+	default n
+	help
+	  Collect DSS IRQ statistics, printable via debugfs.
+
+	  The statistics can be found from
+	  <debugfs>/omapdss/dispc_irq for DISPC interrupts, and
+	  <debugfs>/omapdss/dsi_irq for DSI interrupts.
+
+config OMAP2_DSS_DPI
+	bool "DPI support"
+	default y
+	help
+	  DPI Interface. This is the Parallel Display Interface.
+
+config OMAP2_DSS_VENC
+	bool "VENC support"
+	default y
+	help
+	  OMAP Video Encoder support for S-Video and composite TV-out.
+
+config OMAP2_DSS_HDMI_COMMON
+	bool
+
+config OMAP4_DSS_HDMI
+	bool "HDMI support for OMAP4"
+	default y
+	select OMAP2_DSS_HDMI_COMMON
+	help
+	  HDMI support for OMAP4 based SoCs.
+
+config OMAP4_DSS_HDMI_CEC
+	bool "Enable HDMI CEC support for OMAP4"
+	depends on OMAP4_DSS_HDMI
+	select CEC_CORE
+	default y
+	help
+	  When selected the HDMI transmitter will support the CEC feature.
+
+config OMAP5_DSS_HDMI
+	bool "HDMI support for OMAP5"
+	default n
+	select OMAP2_DSS_HDMI_COMMON
+	help
+	  HDMI Interface for OMAP5 and similar cores. This adds the High
+	  Definition Multimedia Interface. See http://www.hdmi.org/ for HDMI
+	  specification.
+
+config OMAP2_DSS_SDI
+	bool "SDI support"
+	default n
+	help
+	  SDI (Serial Display Interface) support.
+
+	  SDI is a high speed one-way display serial bus between the host
+	  processor and a display.
+
+config OMAP2_DSS_DSI
+	bool "DSI support"
+	default n
+	select DRM_MIPI_DSI
+	help
+	  MIPI DSI (Display Serial Interface) support.
+
+	  DSI is a high speed half-duplex serial interface between the host
+	  processor and a peripheral, such as a display or a framebuffer chip.
+
+	  See http://www.mipi.org/ for DSI specifications.
+
+config OMAP2_DSS_MIN_FCK_PER_PCK
+	int "Minimum FCK/PCK ratio (for scaling)"
+	range 0 32
+	default 0
+	help
+	  This can be used to adjust the minimum FCK/PCK ratio.
+
+	  With this you can make sure that DISPC FCK is at least
+	  n x PCK. Video plane scaling requires higher FCK than
+	  normally.
+
+	  If this is set to 0, there's no extra constraint on the
+	  DISPC FCK. However, the FCK will at minimum be
+	  2xPCK (if active matrix) or 3xPCK (if passive matrix).
+
+	  Max FCK is 173MHz, so this doesn't work if your PCK
+	  is very high.
+
+config OMAP2_DSS_SLEEP_AFTER_VENC_RESET
+	bool "Sleep 20ms after VENC reset"
+	default y
+	help
+	  There is a 20ms sleep after VENC reset which seemed to fix the
+	  reset. The reason for the bug is unclear, and it's also unclear
+	  on what platforms this happens.
+
+	  This option enables the sleep, and is enabled by default. You can
+	  disable the sleep if it doesn't cause problems on your platform.
 
 endif