Merge tag 'armsoc-devicetree' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc

Pull ARM/arm64 Devicetree updates from Olof Johansson:
 "As usual, device tree updates is the bulk of our material in this
  merge window. This time around, 559 patches affecting both 32- and
  64-bit platforms.

  Changes are too many to list individually, but some of the larger
  ones:

  New platform/SoC support:

   - Automotive:
     + Renesas R-Car D3 (R8A77995)
     + TI DT76x
     + MediaTek mt2712e
   - Communication-oriented:
     + Qualcomm IPQ8074
     + Broadcom Stingray
     + Marvell Armada 8080
   - Set top box:
     + Uniphier PXs3

  Besides some vendor reference boards for the SoC above, there are also
  several new boards/machines:

   - TI AM335x Moxa UC-8100-ME-T open platform
   - TI AM57xx Beaglebone X15 Rev C
   - Microchip/Atmel sama5d27 SoM1 EK
   - Broadcom Raspberry Pi Zero W
   - Gemini-based D-Link DIR-685 router
   - Freescale i.MX6:
     + Toradex Apalis module + Apalis and Ixora carrier boards
     + Engicam GEAM6UL Starter Kit
   - Freescale i.MX53-based Beckhoff CX9020 Embedded PC
   - Mediatek mt7623-based BananaPi R2
   - Several Allwinner-based single-board computers:
  + Cubietruck plus
  + Bananapi M3, M2M and M64
  + NanoPi A64
  + A64-OLinuXino
  + Pine64
   - Rockchip RK3328 Pine64/Rock64 board support
   - Rockchip RK3399 boards:
  + RK3399 Sapphire module on Excavator carrier (RK3399 reference design)
  + Theobroma Systems RK3399-Q7 SoM
   - ZTE ZX296718 PCBOX Board"

* tag 'armsoc-devicetree' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (559 commits)
  ARM: dts: at91: at91sam9g45: add AC97
  arm64: dts: marvell: mcbin: enable more networking ports
  arm64: dts: marvell: add a reference to the sysctrl syscon in the ppv2 node
  arm64: dts: marvell: add TX interrupts for PPv2.2
  arm64: dts: uniphier: add PXs3 SoC support
  ARM: dts: uniphier: add pinctrl groups of ethernet phy mode
  ARM: dts: uniphier: fix size of sdctrl nodes
  ARM: dts: uniphier: add AIDET nodes
  arm64: dts: uniphier: fix size of sdctrl node
  arm64: dts: uniphier: add AIDET nodes
  Revert "ARM: dts: sun8i: h3: Enable dwmac-sun8i on the Beelink X2"
  arm64: dts: uniphier: add reset controller node of analog amplifier
  arm64: dts: marvell: add Device Tree files for Armada-8KP
  arm64: dts: rockchip: add Haikou baseboard with RK3399-Q7 SoM
  arm64: dts: rockchip: add RK3399-Q7 (Puma) SoM
  dt-bindings: add rk3399-q7 SoM
  ARM: dts: rockchip: enable usb for rv1108-evb
  ARM: dts: rockchip: add usb nodes for rv1108 SoCs
  dt-bindings: update grf-binding for rv1108 SoCs
  ARM: dts: aspeed-g4: fix AHB window size of the SMC controllers
  ...

1 files changed, 28 insertions, 11 deletions

diff --git a/arch/arm/boot/dts/at91-sama5d2_xplained.dts b/arch/arm/boot/dts/at91-sama5d2_xplained.dts
index 2e2c3d1a1fa2..c7e9ccf2bc87 100644
--- a/arch/arm/boot/dts/at91-sama5d2_xplained.dts
+++ b/arch/arm/boot/dts/at91-sama5d2_xplained.dts
@@ -68,7 +68,7 @@
 
 	ahb {
 		usb0: gadget@00300000 {
-			atmel,vbus-gpio = <&pioA 31 GPIO_ACTIVE_HIGH>;
+			atmel,vbus-gpio = <&pioA PIN_PA31 GPIO_ACTIVE_HIGH>;
 			pinctrl-names = "default";
 			pinctrl-0 = <&pinctrl_usba_vbus>;
 			status = "okay";
@@ -76,8 +76,8 @@
 
 		usb1: ohci@00400000 {
 			num-ports = <3>;
-			atmel,vbus-gpio = <0 /* &pioA 41 GPIO_ACTIVE_HIGH */
-					   &pioA 42 GPIO_ACTIVE_HIGH
+			atmel,vbus-gpio = <0 /* &pioA PIN_PB9 GPIO_ACTIVE_HIGH */
+					   &pioA PIN_PB10 GPIO_ACTIVE_HIGH
 					   0
 					  >;
 			pinctrl-names = "default";
@@ -127,7 +127,7 @@
 				ethernet-phy@1 {
 					reg = <0x1>;
 					interrupt-parent = <&pioA>;
-					interrupts = <73 IRQ_TYPE_LEVEL_LOW>;
+					interrupts = <PIN_PC9 IRQ_TYPE_LEVEL_LOW>;
 				};
 			};
 
@@ -160,9 +160,9 @@
 					compatible = "active-semi,act8945a";
 					reg = <0x5b>;
 					active-semi,vsel-high;
-					active-semi,chglev-gpios = <&pioA 12 GPIO_ACTIVE_HIGH>;
-					active-semi,lbo-gpios = <&pioA 72 GPIO_ACTIVE_LOW>;
-					active-semi,irq_gpios = <&pioA 45 GPIO_ACTIVE_LOW>;
+					active-semi,chglev-gpios = <&pioA PIN_PA12 GPIO_ACTIVE_HIGH>;
+					active-semi,lbo-gpios = <&pioA PIN_PC8 GPIO_ACTIVE_LOW>;
+					active-semi,irq_gpios = <&pioA PIN_PB13 GPIO_ACTIVE_LOW>;
 					active-semi,input-voltage-threshold-microvolt = <6600>;
 					active-semi,precondition-timeout = <40>;
 					active-semi,total-timeout = <3>;
@@ -355,6 +355,14 @@
 					bias-pull-up;
 				};
 
+				pinctrl_classd_default: classd_default {
+					pinmux = <PIN_PB1__CLASSD_R0>,
+						 <PIN_PB2__CLASSD_R1>,
+						 <PIN_PB3__CLASSD_R2>,
+						 <PIN_PB4__CLASSD_R3>;
+					bias-pull-up;
+				};
+
 				pinctrl_flx0_default: flx0_default {
 					pinmux = <PIN_PB28__FLEXCOM0_IO0>,
 						 <PIN_PB29__FLEXCOM0_IO1>;
@@ -488,6 +496,14 @@
 
 			};
 
+			classd: classd@fc048000 {
+				pinctrl-names = "default";
+				pinctrl-0 = <&pinctrl_classd_default>;
+				atmel,pwm-type = "diff";
+				atmel,non-overlap-time = <10>;
+				status = "okay";
+			};
+
 			can1: can@fc050000 {
 				pinctrl-names = "default";
 				pinctrl-0 = <&pinctrl_can1_default>;
@@ -504,7 +520,7 @@
 
 		bp1 {
 			label = "PB_USER";
-			gpios = <&pioA 41 GPIO_ACTIVE_LOW>;
+			gpios = <&pioA PIN_PB9 GPIO_ACTIVE_LOW>;
 			linux,code = <0x104>;
 		};
 	};
@@ -517,17 +533,18 @@
 
 		red {
 			label = "red";
-			gpios = <&pioA 38 GPIO_ACTIVE_LOW>;
+			gpios = <&pioA PIN_PB6 GPIO_ACTIVE_LOW>;
 		};
 
+
 		green {
 			label = "green";
-			gpios = <&pioA 37 GPIO_ACTIVE_LOW>;
+			gpios = <&pioA PIN_PB5 GPIO_ACTIVE_LOW>;
 		};
 
 		blue {
 			label = "blue";
-			gpios = <&pioA 32 GPIO_ACTIVE_LOW>;
+			gpios = <&pioA PIN_PB0 GPIO_ACTIVE_LOW>;
 			linux,default-trigger = "heartbeat";
 		};
 	};