Merge branch 'i2c/for-next' of git://git.kernel.org/pub/scm/linux/kernel/git/wsa/linux

Pull more i2c updates from Wolfram Sang:
 "I2C has two more new drivers: Altera FPGA and STM32F7"

* 'i2c/for-next' of git://git.kernel.org/pub/scm/linux/kernel/git/wsa/linux:
  i2c: i2c-stm32f7: add driver
  i2c: i2c-stm32f4: use generic definition of speed enum
  dt-bindings: i2c-stm32: Document the STM32F7 I2C bindings
  i2c: altera: Add Altera I2C Controller driver
  dt-bindings: i2c: Add Altera I2C Controller

2 files changed, 65 insertions, 3 deletions

diff --git a/Documentation/devicetree/bindings/i2c/i2c-altera.txt b/Documentation/devicetree/bindings/i2c/i2c-altera.txt
new file mode 100644
index 000000000000..767664f448ec
--- /dev/null
+++ b/Documentation/devicetree/bindings/i2c/i2c-altera.txt
@@ -0,0 +1,39 @@
+* Altera I2C Controller
+* This is Altera's synthesizable logic block I2C Controller for use
+* in Altera's FPGAs.
+
+Required properties :
+ - compatible : should be "altr,softip-i2c-v1.0"
+ - reg        : Offset and length of the register set for the device
+ - interrupts : <IRQ> where IRQ is the interrupt number.
+ - clocks     : phandle to input clock.
+ - #address-cells = <1>;
+ - #size-cells = <0>;
+
+Recommended properties :
+ - clock-frequency : desired I2C bus clock frequency in Hz.
+
+Optional properties :
+ - fifo-size : Size of the RX and TX FIFOs in bytes.
+ - Child nodes conforming to i2c bus binding
+
+Example :
+
+	i2c@100080000 {
+		compatible = "altr,softip-i2c-v1.0";
+		reg = <0x00000001 0x00080000 0x00000040>;
+		interrupt-parent = <&intc>;
+		interrupts = <0 43 4>;
+		clocks = <&clk_0>;
+		clock-frequency = <100000>;
+		#address-cells = <1>;
+		#size-cells = <0>;
+		fifo-size = <4>;
+
+		eeprom@51 {
+			compatible = "atmel,24c32";
+			reg = <0x51>;
+			pagesize = <32>;
+		};
+	};
+
diff --git a/Documentation/devicetree/bindings/i2c/i2c-stm32.txt b/Documentation/devicetree/bindings/i2c/i2c-stm32.txt
index 78eaf7b718ed..3b5489966634 100644
--- a/Documentation/devicetree/bindings/i2c/i2c-stm32.txt
+++ b/Documentation/devicetree/bindings/i2c/i2c-stm32.txt
@@ -1,7 +1,9 @@
 * I2C controller embedded in STMicroelectronics STM32 I2C platform
 
 Required properties :
-- compatible : Must be "st,stm32f4-i2c"
+- compatible : Must be one of the following
+  - "st,stm32f4-i2c"
+  - "st,stm32f7-i2c"
 - reg : Offset and length of the register set for the device
 - interrupts : Must contain the interrupt id for I2C event and then the
   interrupt id for I2C error.
@@ -14,8 +16,16 @@ Required properties :
 
 Optional properties :
 - clock-frequency : Desired I2C bus clock frequency in Hz. If not specified,
-  the default 100 kHz frequency will be used. As only Normal and Fast modes
-  are supported, possible values are 100000 and 400000.
+  the default 100 kHz frequency will be used.
+  For STM32F4 SoC Standard-mode and Fast-mode are supported, possible values are
+  100000 and 400000.
+  For STM32F7 SoC, Standard-mode, Fast-mode and Fast-mode Plus are supported,
+  possible values are 100000, 400000 and 1000000.
+- i2c-scl-rising-time-ns : Only for STM32F7, I2C SCL Rising time for the board
+  (default: 25)
+- i2c-scl-falling-time-ns : Only for STM32F7, I2C SCL Falling time for the board
+  (default: 10)
+  I2C Timings are derived from these 2 values
 
 Example :
 
@@ -31,3 +41,16 @@ Example :
 		pinctrl-0 = <&i2c1_sda_pin>, <&i2c1_scl_pin>;
 		pinctrl-names = "default";
 	};
+
+	i2c@40005400 {
+		compatible = "st,stm32f7-i2c";
+		#address-cells = <1>;
+		#size-cells = <0>;
+		reg = <0x40005400 0x400>;
+		interrupts = <31>,
+			     <32>;
+		resets = <&rcc STM32F7_APB1_RESET(I2C1)>;
+		clocks = <&rcc 1 CLK_I2C1>;
+		pinctrl-0 = <&i2c1_sda_pin>, <&i2c1_scl_pin>;
+		pinctrl-names = "default";
+	};