Merge tag 'pinctrl-v5.9-1' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-pinctrl

Pull pin control updates from Linus Walleij:
 "This is the bulk of the pin control changes for the v5.9 kernel
  series:

  Core changes:

   - The GPIO patch "gpiolib: Introduce for_each_requested_gpio_in_range()
     macro" was put in an immutable branch and merged into the pinctrl
     tree as well. We see these changes also here.

   - Improved debug output for pins used as GPIO.

  New drivers:

   - Ocelot Sparx5 SoC driver.

   - Intel Emmitsburg SoC subdriver.

   - Intel Tiger Lake-H SoC subdriver.

   - Qualcomm PM660 SoC subdriver.

   - Renesas SH-PFC R8A774E1 subdriver.

  Driver improvements:

   - Linear improvement and cleanups of the Intel drivers for
     Cherryview, Lynxpoint, Baytrail etc. Improved locking among other
     things.

   - Renesas SH-PFC has added support for RPC pins, groups, and
     functions to r8a77970 and r8a77980.

   - The newere Freescale (now NXP) i.MX8 pin controllers have been
     modularized. This is driven by the Google Android GKI initiative I
     think.

   - Open drain support for pins on the Qualcomm IPQ4019.

   - The Ingenic driver can handle both edges IRQ detection.

   - A big slew of documentation fixes all over the place.

   - A few irqchip template conversions by yours truly.

* tag 'pinctrl-v5.9-1' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-pinctrl: (107 commits)
  dt-bindings: pinctrl: add bindings for MediaTek MT6779 SoC
  pinctrl: stmfx: Use irqchip template
  pinctrl: amd: Use irqchip template
  pinctrl: mediatek: fix build for tristate changes
  pinctrl: samsung: Use bank name as irqchip name
  pinctrl: core: print gpio in pins debugfs file
  pinctrl: mediatek: add mt6779 eint support
  pinctrl: mediatek: add pinctrl support for MT6779 SoC
  pinctrl: mediatek: avoid virtual gpio trying to set reg
  pinctrl: mediatek: update pinmux definitions for mt6779
  pinctrl: stm32: use the hwspin_lock_timeout_in_atomic() API
  pinctrl: mcp23s08: Use irqchip template
  pinctrl: sx150x: Use irqchip template
  dt-bindings: ingenic,pinctrl: Support pinmux/pinconf nodes
  pinctrl: intel: Add Intel Emmitsburg pin controller support
  pinctl: ti: iodelay: Replace HTTP links with HTTPS ones
  Revert "gpio: omap: handle pin config bias flags"
  pinctrl: single: Use fallthrough pseudo-keyword
  pinctrl: qcom: spmi-gpio: Use fallthrough pseudo-keyword
  pinctrl: baytrail: Use fallthrough pseudo-keyword
  ...

8 files changed, 483 insertions, 169 deletions

diff --git a/Documentation/devicetree/bindings/pinctrl/ingenic,pinctrl.txt b/Documentation/devicetree/bindings/pinctrl/ingenic,pinctrl.txt
deleted file mode 100644
index d9b2100c98e8..000000000000
--- a/Documentation/devicetree/bindings/pinctrl/ingenic,pinctrl.txt
+++ /dev/null
@@ -1,81 +0,0 @@
-Ingenic XBurst pin controller
-
-Please refer to pinctrl-bindings.txt in this directory for details of the
-common pinctrl bindings used by client devices, including the meaning of the
-phrase "pin configuration node".
-
-For the XBurst SoCs, pin control is tightly bound with GPIO ports. All pins may
-be used as GPIOs, multiplexed device functions are configured within the
-GPIO port configuration registers and it is typical to refer to pins using the
-naming scheme "PxN" where x is a character identifying the GPIO port with
-which the pin is associated and N is an integer from 0 to 31 identifying the
-pin within that GPIO port. For example PA0 is the first pin in GPIO port A, and
-PB31 is the last pin in GPIO port B. The jz4740, the x1000 and the x1830
-contains 4 GPIO ports, PA to PD, for a total of 128 pins. The jz4760, the
-jz4770 and the jz4780 contains 6 GPIO ports, PA to PF, for a total of 192 pins.
-
-
-Required properties:
---------------------
-
- - compatible: One of:
-    - "ingenic,jz4740-pinctrl"
-    - "ingenic,jz4725b-pinctrl"
-    - "ingenic,jz4760-pinctrl"
-    - "ingenic,jz4760b-pinctrl"
-    - "ingenic,jz4770-pinctrl"
-    - "ingenic,jz4780-pinctrl"
-    - "ingenic,x1000-pinctrl"
-    - "ingenic,x1000e-pinctrl"
-    - "ingenic,x1500-pinctrl"
-    - "ingenic,x1830-pinctrl"
- - reg: Address range of the pinctrl registers.
-
-
-Required properties for sub-nodes (GPIO chips):
------------------------------------------------
-
- - compatible: Must contain one of:
-    - "ingenic,jz4740-gpio"
-    - "ingenic,jz4760-gpio"
-    - "ingenic,jz4770-gpio"
-    - "ingenic,jz4780-gpio"
-    - "ingenic,x1000-gpio"
-    - "ingenic,x1830-gpio"
- - reg: The GPIO bank number.
- - interrupt-controller: Marks the device node as an interrupt controller.
- - interrupts: Interrupt specifier for the controllers interrupt.
- - #interrupt-cells: Should be 2. Refer to
-   ../interrupt-controller/interrupts.txt for more details.
- - gpio-controller: Marks the device node as a GPIO controller.
- - #gpio-cells: Should be 2. The first cell is the GPIO number and the second
-    cell specifies GPIO flags, as defined in <dt-bindings/gpio/gpio.h>. Only the
-    GPIO_ACTIVE_HIGH and GPIO_ACTIVE_LOW flags are supported.
- - gpio-ranges: Range of pins managed by the GPIO controller. Refer to
-   ../gpio/gpio.txt for more details.
-
-
-Example:
---------
-
-pinctrl: pin-controller@10010000 {
-	compatible = "ingenic,jz4740-pinctrl";
-	reg = <0x10010000 0x400>;
-	#address-cells = <1>;
-	#size-cells = <0>;
-
-	gpa: gpio@0 {
-		compatible = "ingenic,jz4740-gpio";
-		reg = <0>;
-
-		gpio-controller;
-		gpio-ranges = <&pinctrl 0 0 32>;
-		#gpio-cells = <2>;
-
-		interrupt-controller;
-		#interrupt-cells = <2>;
-
-		interrupt-parent = <&intc>;
-		interrupts = <28>;
-	};
-};
diff --git a/Documentation/devicetree/bindings/pinctrl/ingenic,pinctrl.yaml b/Documentation/devicetree/bindings/pinctrl/ingenic,pinctrl.yaml
new file mode 100644
index 000000000000..18163fb69ce7
--- /dev/null
+++ b/Documentation/devicetree/bindings/pinctrl/ingenic,pinctrl.yaml
@@ -0,0 +1,176 @@
+# SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause)
+%YAML 1.2
+---
+$id: http://devicetree.org/schemas/pinctrl/ingenic,pinctrl.yaml#
+$schema: http://devicetree.org/meta-schemas/core.yaml#
+
+title: Ingenic SoCs pin controller devicetree bindings
+
+description: >
+  Please refer to pinctrl-bindings.txt in this directory for details of the
+  common pinctrl bindings used by client devices, including the meaning of the
+  phrase "pin configuration node".
+
+  For the Ingenic SoCs, pin control is tightly bound with GPIO ports. All pins
+  may be used as GPIOs, multiplexed device functions are configured within the
+  GPIO port configuration registers and it is typical to refer to pins using the
+  naming scheme "PxN" where x is a character identifying the GPIO port with
+  which the pin is associated and N is an integer from 0 to 31 identifying the
+  pin within that GPIO port. For example PA0 is the first pin in GPIO port A,
+  and PB31 is the last pin in GPIO port B. The JZ4740, the X1000 and the X1830
+  contains 4 GPIO ports, PA to PD, for a total of 128 pins. The JZ4760, the
+  JZ4770 and the JZ4780 contains 6 GPIO ports, PA to PF, for a total of 192
+  pins.
+
+maintainers:
+  - Paul Cercueil <paul@crapouillou.net>
+
+properties:
+  nodename:
+    pattern: "^pinctrl@[0-9a-f]+$"
+
+  compatible:
+    oneOf:
+      - enum:
+        - ingenic,jz4740-pinctrl
+        - ingenic,jz4725b-pinctrl
+        - ingenic,jz4760-pinctrl
+        - ingenic,jz4770-pinctrl
+        - ingenic,jz4780-pinctrl
+        - ingenic,x1000-pinctrl
+        - ingenic,x1500-pinctrl
+        - ingenic,x1830-pinctrl
+      - items:
+        - const: ingenic,jz4760b-pinctrl
+        - const: ingenic,jz4760-pinctrl
+      - items:
+        - const: ingenic,x1000e-pinctrl
+        - const: ingenic,x1000-pinctrl
+
+  reg:
+    maxItems: 1
+
+  "#address-cells":
+    const: 1
+
+  "#size-cells":
+    const: 0
+
+patternProperties:
+  "^gpio@[0-9]$":
+    type: object
+    properties:
+      compatible:
+        enum:
+          - ingenic,jz4740-gpio
+          - ingenic,jz4725b-gpio
+          - ingenic,jz4760-gpio
+          - ingenic,jz4770-gpio
+          - ingenic,jz4780-gpio
+          - ingenic,x1000-gpio
+          - ingenic,x1500-gpio
+          - ingenic,x1830-gpio
+
+      reg:
+        items:
+          - description: The GPIO bank number
+
+      gpio-controller: true
+
+      "#gpio-cells":
+        const: 2
+
+      gpio-ranges:
+        maxItems: 1
+
+      interrupt-controller: true
+
+      "#interrupt-cells":
+        const: 2
+        description:
+          Refer to ../interrupt-controller/interrupts.txt for more details.
+
+      interrupts:
+        maxItems: 1
+
+    required:
+      - compatible
+      - reg
+      - gpio-controller
+      - "#gpio-cells"
+      - interrupts
+      - interrupt-controller
+      - "#interrupt-cells"
+
+    additionalProperties: false
+
+required:
+  - compatible
+  - reg
+  - "#address-cells"
+  - "#size-cells"
+
+additionalProperties:
+  anyOf:
+    - type: object
+      allOf:
+        - $ref: pincfg-node.yaml#
+        - $ref: pinmux-node.yaml#
+
+      properties:
+        phandle: true
+        function: true
+        groups: true
+        pins: true
+        bias-disable: true
+        bias-pull-up: true
+        bias-pull-down: true
+        output-low: true
+        output-high: true
+      additionalProperties: false
+
+    - type: object
+      properties:
+        phandle: true
+      additionalProperties:
+        type: object
+        allOf:
+          - $ref: pincfg-node.yaml#
+          - $ref: pinmux-node.yaml#
+
+        properties:
+          phandle: true
+          function: true
+          groups: true
+          pins: true
+          bias-disable: true
+          bias-pull-up: true
+          bias-pull-down: true
+          output-low: true
+          output-high: true
+        additionalProperties: false
+
+examples:
+  - |
+    pin-controller@10010000 {
+      compatible = "ingenic,jz4770-pinctrl";
+      reg = <0x10010000 0x600>;
+
+      #address-cells = <1>;
+      #size-cells = <0>;
+
+      gpio@0 {
+        compatible = "ingenic,jz4770-gpio";
+        reg = <0>;
+
+        gpio-controller;
+        gpio-ranges = <&pinctrl 0 0 32>;
+        #gpio-cells = <2>;
+
+        interrupt-controller;
+        #interrupt-cells = <2>;
+
+        interrupt-parent = <&intc>;
+        interrupts = <17>;
+      };
+    };
diff --git a/Documentation/devicetree/bindings/pinctrl/mediatek,mt6779-pinctrl.yaml b/Documentation/devicetree/bindings/pinctrl/mediatek,mt6779-pinctrl.yaml
new file mode 100644
index 000000000000..152c151c27ad
--- /dev/null
+++ b/Documentation/devicetree/bindings/pinctrl/mediatek,mt6779-pinctrl.yaml
@@ -0,0 +1,202 @@
+# SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause)
+%YAML 1.2
+---
+$id: http://devicetree.org/schemas/pinctrl/mediatek,mt6779-pinctrl.yaml#
+$schema: http://devicetree.org/meta-schemas/core.yaml#
+
+title: Mediatek MT6779 Pin Controller Device Tree Bindings
+
+maintainers:
+  - Andy Teng <andy.teng@mediatek.com>
+
+description: |+
+  The pin controller node should be the child of a syscon node with the
+  required property:
+  - compatible: "syscon"
+
+properties:
+  compatible:
+    const: mediatek,mt6779-pinctrl
+
+  reg:
+    minItems: 9
+    maxItems: 9
+
+  reg-names:
+    items:
+      - const: "gpio"
+      - const: "iocfg_rm"
+      - const: "iocfg_br"
+      - const: "iocfg_lm"
+      - const: "iocfg_lb"
+      - const: "iocfg_rt"
+      - const: "iocfg_lt"
+      - const: "iocfg_tl"
+      - const: "eint"
+
+  gpio-controller: true
+
+  "#gpio-cells":
+    const: 2
+    description: |
+      Number of cells in GPIO specifier. Since the generic GPIO
+      binding is used, the amount of cells must be specified as 2. See the below
+      mentioned gpio binding representation for description of particular cells.
+
+  gpio-ranges:
+    minItems: 1
+    maxItems: 5
+    description: |
+      GPIO valid number range.
+
+  interrupt-controller: true
+
+  interrupts:
+    maxItems: 1
+    description: |
+      Specifies the summary IRQ.
+
+  "#interrupt-cells":
+    const: 2
+
+required:
+  - compatible
+  - reg
+  - reg-names
+  - gpio-controller
+  - "#gpio-cells"
+  - gpio-ranges
+  - interrupt-controller
+  - interrupts
+  - "#interrupt-cells"
+
+patternProperties:
+  '-[0-9]*$':
+    type: object
+    patternProperties:
+      '-pins*$':
+        type: object
+        description: |
+          A pinctrl node should contain at least one subnodes representing the
+          pinctrl groups available on the machine. Each subnode will list the
+          pins it needs, and how they should be configured, with regard to muxer
+          configuration, pullups, drive strength, input enable/disable and input schmitt.
+        $ref: "/schemas/pinctrl/pincfg-node.yaml"
+
+        properties:
+          pinmux:
+            description:
+              integer array, represents gpio pin number and mux setting.
+              Supported pin number and mux varies for different SoCs, and are defined
+              as macros in boot/dts/<soc>-pinfunc.h directly.
+
+          bias-disable: true
+
+          bias-pull-up: true
+
+          bias-pull-down: true
+
+          input-enable: true
+
+          input-disable: true
+
+          output-low: true
+
+          output-high: true
+
+          input-schmitt-enable: true
+
+          input-schmitt-disable: true
+
+          mediatek,pull-up-adv:
+            description: |
+              Pull up setings for 2 pull resistors, R0 and R1. User can
+              configure those special pins. Valid arguments are described as below:
+              0: (R1, R0) = (0, 0) which means R1 disabled and R0 disabled.
+              1: (R1, R0) = (0, 1) which means R1 disabled and R0 enabled.
+              2: (R1, R0) = (1, 0) which means R1 enabled and R0 disabled.
+              3: (R1, R0) = (1, 1) which means R1 enabled and R0 enabled.
+            $ref: /schemas/types.yaml#/definitions/uint32
+            enum: [0, 1, 2, 3]
+
+          mediatek,pull-down-adv:
+            description: |
+              Pull down settings for 2 pull resistors, R0 and R1. User can
+              configure those special pins. Valid arguments are described as below:
+              0: (R1, R0) = (0, 0) which means R1 disabled and R0 disabled.
+              1: (R1, R0) = (0, 1) which means R1 disabled and R0 enabled.
+              2: (R1, R0) = (1, 0) which means R1 enabled and R0 disabled.
+              3: (R1, R0) = (1, 1) which means R1 enabled and R0 enabled.
+            $ref: /schemas/types.yaml#/definitions/uint32
+            enum: [0, 1, 2, 3]
+
+        required:
+          - pinmux
+
+        additionalProperties: false
+
+additionalProperties: false
+
+examples:
+  - |
+    #include <dt-bindings/interrupt-controller/irq.h>
+    #include <dt-bindings/interrupt-controller/arm-gic.h>
+    #include <dt-bindings/pinctrl/mt6779-pinfunc.h>
+
+    soc {
+        #address-cells = <2>;
+        #size-cells = <2>;
+
+        pio: pinctrl@10005000 {
+            compatible = "mediatek,mt6779-pinctrl";
+            reg = <0 0x10005000 0 0x1000>,
+                <0 0x11c20000 0 0x1000>,
+                <0 0x11d10000 0 0x1000>,
+                <0 0x11e20000 0 0x1000>,
+                <0 0x11e70000 0 0x1000>,
+                <0 0x11ea0000 0 0x1000>,
+                <0 0x11f20000 0 0x1000>,
+                <0 0x11f30000 0 0x1000>,
+                <0 0x1000b000 0 0x1000>;
+            reg-names = "gpio", "iocfg_rm",
+              "iocfg_br", "iocfg_lm",
+              "iocfg_lb", "iocfg_rt",
+              "iocfg_lt", "iocfg_tl",
+              "eint";
+            gpio-controller;
+            #gpio-cells = <2>;
+            gpio-ranges = <&pio 0 0 210>;
+            interrupt-controller;
+            #interrupt-cells = <2>;
+            interrupts = <GIC_SPI 204 IRQ_TYPE_LEVEL_HIGH>;
+
+            mmc0_pins_default: mmc0-0 {
+                cmd-dat-pins {
+                    pinmux = <PINMUX_GPIO168__FUNC_MSDC0_DAT0>,
+                        <PINMUX_GPIO172__FUNC_MSDC0_DAT1>,
+                        <PINMUX_GPIO169__FUNC_MSDC0_DAT2>,
+                        <PINMUX_GPIO177__FUNC_MSDC0_DAT3>,
+                        <PINMUX_GPIO170__FUNC_MSDC0_DAT4>,
+                        <PINMUX_GPIO173__FUNC_MSDC0_DAT5>,
+                        <PINMUX_GPIO171__FUNC_MSDC0_DAT6>,
+                        <PINMUX_GPIO174__FUNC_MSDC0_DAT7>,
+                        <PINMUX_GPIO167__FUNC_MSDC0_CMD>;
+                    input-enable;
+                    mediatek,pull-up-adv = <1>;
+                };
+                clk-pins {
+                    pinmux = <PINMUX_GPIO176__FUNC_MSDC0_CLK>;
+                    mediatek,pull-down-adv = <2>;
+                };
+                rst-pins {
+                    pinmux = <PINMUX_GPIO178__FUNC_MSDC0_RSTB>;
+                    mediatek,pull-up-adv = <0>;
+                };
+            };
+        };
+
+        mmc0 {
+           pinctrl-0 = <&mmc0_pins_default>;
+           pinctrl-names = "default";
+        };
+    };
diff --git a/Documentation/devicetree/bindings/pinctrl/qcom,ipq4019-pinctrl.txt b/Documentation/devicetree/bindings/pinctrl/qcom,ipq4019-pinctrl.txt
index 84be0f2c6f3b..0861afeccfc9 100644
--- a/Documentation/devicetree/bindings/pinctrl/qcom,ipq4019-pinctrl.txt
+++ b/Documentation/devicetree/bindings/pinctrl/qcom,ipq4019-pinctrl.txt
@@ -44,7 +44,8 @@ information about e.g. the mux function.
 
 The following generic properties as defined in pinctrl-bindings.txt are valid
 to specify in a pin configuration subnode:
- pins, function, bias-disable, bias-pull-down, bias-pull-up, drive-strength.
+ pins, function, bias-disable, bias-pull-down, bias-pull-up, drive-open-drain,
+ drive-strength.
 
 Non-empty subnodes must specify the 'pins' property.
 Note that not all properties are valid for all pins.
diff --git a/Documentation/devicetree/bindings/pinctrl/qcom,pmic-gpio.txt b/Documentation/devicetree/bindings/pinctrl/qcom,pmic-gpio.txt
index 7be5de8d253f..c3d1914381ae 100644
--- a/Documentation/devicetree/bindings/pinctrl/qcom,pmic-gpio.txt
+++ b/Documentation/devicetree/bindings/pinctrl/qcom,pmic-gpio.txt
@@ -23,6 +23,8 @@ PMIC's from Qualcomm.
 		    "qcom,pmi8994-gpio"
 		    "qcom,pmi8998-gpio"
 		    "qcom,pms405-gpio"
+		    "qcom,pm660-gpio"
+		    "qcom,pm660l-gpio"
 		    "qcom,pm8150-gpio"
 		    "qcom,pm8150b-gpio"
 		    "qcom,pm6150-gpio"
diff --git a/Documentation/devicetree/bindings/pinctrl/renesas,pfc-pinctrl.txt b/Documentation/devicetree/bindings/pinctrl/renesas,pfc-pinctrl.txt
index 1b8e8b4a6379..d75476e24514 100644
--- a/Documentation/devicetree/bindings/pinctrl/renesas,pfc-pinctrl.txt
+++ b/Documentation/devicetree/bindings/pinctrl/renesas,pfc-pinctrl.txt
@@ -21,6 +21,7 @@ Required Properties:
     - "renesas,pfc-r8a774a1": for R8A774A1 (RZ/G2M) compatible pin-controller.
     - "renesas,pfc-r8a774b1": for R8A774B1 (RZ/G2N) compatible pin-controller.
     - "renesas,pfc-r8a774c0": for R8A774C0 (RZ/G2E) compatible pin-controller.
+    - "renesas,pfc-r8a774e1": for R8A774E1 (RZ/G2H) compatible pin-controller.
     - "renesas,pfc-r8a7778": for R8A7778 (R-Car M1) compatible pin-controller.
     - "renesas,pfc-r8a7779": for R8A7779 (R-Car H1) compatible pin-controller.
     - "renesas,pfc-r8a7790": for R8A7790 (R-Car H2) compatible pin-controller.
diff --git a/Documentation/devicetree/bindings/pinctrl/renesas,rza2-pinctrl.txt b/Documentation/devicetree/bindings/pinctrl/renesas,rza2-pinctrl.txt
deleted file mode 100644
index a63ccd476cda..000000000000
--- a/Documentation/devicetree/bindings/pinctrl/renesas,rza2-pinctrl.txt
+++ /dev/null
@@ -1,87 +0,0 @@
-Renesas RZ/A2 combined Pin and GPIO controller
-
-The Renesas SoCs of the RZ/A2 series feature a combined Pin and GPIO controller.
-Pin multiplexing and GPIO configuration is performed on a per-pin basis.
-Each port features up to 8 pins, each of them configurable for GPIO
-function (port mode) or in alternate function mode.
-Up to 8 different alternate function modes exist for each single pin.
-
-Pin controller node
--------------------
-
-Required properties:
-  - compatible: shall be:
-    - "renesas,r7s9210-pinctrl": for RZ/A2M
-  - reg
-    Address base and length of the memory area where the pin controller
-    hardware is mapped to.
-  - gpio-controller
-    This pin controller also controls pins as GPIO
-  - #gpio-cells
-    Must be 2
-  - gpio-ranges
-    Expresses the total number of GPIO ports/pins in this SoC
-
-Example: Pin controller node for RZ/A2M SoC (r7s9210)
-
-	pinctrl: pin-controller@fcffe000 {
-		compatible = "renesas,r7s9210-pinctrl";
-		reg = <0xfcffe000 0x1000>;
-
-		gpio-controller;
-		#gpio-cells = <2>;
-		gpio-ranges = <&pinctrl 0 0 176>;
-	};
-
-Sub-nodes
----------
-
-The child nodes of the pin controller designate pins to be used for
-specific peripheral functions or as GPIO.
-
-- Pin multiplexing sub-nodes:
-  A pin multiplexing sub-node describes how to configure a set of
-  (or a single) pin in some desired alternate function mode.
-  The values for the pinmux properties are a combination of port name, pin
-  number and the desired function index. Use the RZA2_PINMUX macro located
-  in include/dt-bindings/pinctrl/r7s9210-pinctrl.h to easily define these.
-  For assigning GPIO pins, use the macro RZA2_PIN also in r7s9210-pinctrl.h
-  to express the desired port pin.
-
-  Required properties:
-    - pinmux:
-      integer array representing pin number and pin multiplexing configuration.
-      When a pin has to be configured in alternate function mode, use this
-      property to identify the pin by its global index, and provide its
-      alternate function configuration number along with it.
-      When multiple pins are required to be configured as part of the same
-      alternate function they shall be specified as members of the same
-      argument list of a single "pinmux" property.
-      Helper macros to ease assembling the pin index from its position
-      (port where it sits on and pin number) and alternate function identifier
-      are provided by the pin controller header file at:
-      <dt-bindings/pinctrl/r7s9210-pinctrl.h>
-      Integers values in "pinmux" argument list are assembled as:
-      ((PORT * 8 + PIN) | MUX_FUNC << 16)
-
-  Example: Board specific pins configuration
-
-	&pinctrl {
-		/* Serial Console */
-		scif4_pins: serial4 {
-			pinmux = <RZA2_PINMUX(PORT9, 0, 4)>,	/* TxD4 */
-				 <RZA2_PINMUX(PORT9, 1, 4)>;	/* RxD4 */
-		};
-	};
-
-  Example: Assigning a GPIO:
-
-	leds {
-		status = "okay";
-		compatible = "gpio-leds";
-
-		led0 {
-			/* P6_0 */
-			gpios = <&pinctrl RZA2_PIN(PORT6, 0) GPIO_ACTIVE_HIGH>;
-		};
-	};
diff --git a/Documentation/devicetree/bindings/pinctrl/renesas,rza2-pinctrl.yaml b/Documentation/devicetree/bindings/pinctrl/renesas,rza2-pinctrl.yaml
new file mode 100644
index 000000000000..b7911a994f3a
--- /dev/null
+++ b/Documentation/devicetree/bindings/pinctrl/renesas,rza2-pinctrl.yaml
@@ -0,0 +1,100 @@
+# SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause)
+%YAML 1.2
+---
+$id: http://devicetree.org/schemas/pinctrl/renesas,rza2-pinctrl.yaml#
+$schema: http://devicetree.org/meta-schemas/core.yaml#
+
+title: Renesas RZ/A2 combined Pin and GPIO controller
+
+maintainers:
+  - Chris Brandt <chris.brandt@renesas.com>
+  - Geert Uytterhoeven <geert+renesas@glider.be>
+
+description:
+  The Renesas SoCs of the RZ/A2 series feature a combined Pin and GPIO
+  controller.
+  Pin multiplexing and GPIO configuration is performed on a per-pin basis.
+  Each port features up to 8 pins, each of them configurable for GPIO function
+  (port mode) or in alternate function mode.
+  Up to 8 different alternate function modes exist for each single pin.
+
+properties:
+  compatible:
+    const: "renesas,r7s9210-pinctrl" # RZ/A2M
+
+  reg:
+    maxItems: 1
+
+  gpio-controller: true
+
+  '#gpio-cells':
+    const: 2
+    description:
+      The first cell contains the global GPIO port index, constructed using the
+      RZA2_PIN() helper macro in r7s9210-pinctrl.h.
+      E.g. "RZA2_PIN(PORT6, 0)" for P6_0.
+
+  gpio-ranges:
+    maxItems: 1
+
+patternProperties:
+  "^.*$":
+    if:
+      type: object
+    then:
+      allOf:
+        - $ref: pincfg-node.yaml#
+        - $ref: pinmux-node.yaml#
+      description:
+        The child nodes of the pin controller designate pins to be used for
+        specific peripheral functions or as GPIO.
+
+        A pin multiplexing sub-node describes how to configure a set of
+        (or a single) pin in some desired alternate function mode.
+        The values for the pinmux properties are a combination of port name,
+        pin number and the desired function index. Use the RZA2_PINMUX macro
+        located in include/dt-bindings/pinctrl/r7s9210-pinctrl.h to easily
+        define these.
+        For assigning GPIO pins, use the macro RZA2_PIN also in
+        to express the desired port pin.
+
+      properties:
+        phandle: true
+
+        pinmux:
+          description:
+            Values are constructed from GPIO port number, pin number, and
+            alternate function configuration number using the RZA2_PINMUX()
+            helper macro in r7s9210-pinctrl.h.
+
+      required:
+        - pinmux
+
+      additionalProperties: false
+
+required:
+  - compatible
+  - reg
+  - gpio-controller
+  - '#gpio-cells'
+  - gpio-ranges
+
+additionalProperties: false
+
+examples:
+  - |
+    #include <dt-bindings/pinctrl/r7s9210-pinctrl.h>
+    pinctrl: pin-controller@fcffe000 {
+            compatible = "renesas,r7s9210-pinctrl";
+            reg = <0xfcffe000 0x1000>;
+
+            gpio-controller;
+            #gpio-cells = <2>;
+            gpio-ranges = <&pinctrl 0 0 176>;
+
+            /* Serial Console */
+            scif4_pins: serial4 {
+                    pinmux = <RZA2_PINMUX(PORT9, 0, 4)>, /* TxD4 */
+                             <RZA2_PINMUX(PORT9, 1, 4)>; /* RxD4 */
+            };
+    };