Merge tag 'pinctrl-v6.9-1' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-pinctrl

Pull pin control updates from Linus Walleij:
 "No core changes this time around.

  New drivers:

   - New driver for Renesas R8A779H0 also known as R-Car V4M.

   - New driver for the Awinic AW9523/B I2C GPIO expander. I found this
     living out-of-tree in OpenWrt as an upstream attempt had stalled on
     the finishing line, so I picked it up and finished the job.

  Improvements:

   - The Nomadik pin control driver was for years re-used out of tree
     for the ST STA chips, and now the IP was re-used in a MIPS
     automotive SoC called MobilEyeq5, so it has been split in pin
     control and GPIO drivers so the latter can be reused by MobilEyeq5.
     (Along with a long list of cleanups)

   - A lot of overall cleanup and tidying up"

* tag 'pinctrl-v6.9-1' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-pinctrl: (87 commits)
  drivers/gpio/nomadik: move dummy nmk_gpio_dbg_show_one() to header
  gpio: nomadik: remove BUG_ON() in nmk_gpio_populate_chip()
  dt-bindings: pinctrl: qcom: update compatible name for match with driver
  pinctrl: aw9523: Make the driver tristate
  pinctrl: nomadik: fix dereference of error pointer
  gpio: nomadik: Back out some managed resources
  pinctrl: aw9523: Add proper terminator
  pinctrl: core: comment that pinctrl_add_gpio_range() is deprecated
  pinctrl: pinmux: Suppress error message for -EPROBE_DEFER
  pinctrl: Add driver for Awinic AW9523/B I2C GPIO Expander
  dt-bindings: pinctrl: Add bindings for Awinic AW9523/AW9523B
  gpio: nomadik: Finish conversion to use firmware node APIs
  gpio: nomadik: fix Kconfig dependencies inbetween pinctrl & GPIO
  pinctrl: da9062: Add OF table
  dt-bindings: pinctrl: at91: add sam9x7
  pinctrl: ocelot: remove redundant assignment to variable ret
  gpio: nomadik: grab optional reset control and deassert it at probe
  gpio: nomadik: support mobileye,eyeq5-gpio
  gpio: nomadik: handle variadic GPIO count
  gpio: nomadik: support shared GPIO IRQs
  ...

21 files changed, 560 insertions, 100 deletions

diff --git a/Documentation/devicetree/bindings/gpio/gpio-nmk.txt b/Documentation/devicetree/bindings/gpio/gpio-nmk.txt
deleted file mode 100644
index 8315ac7780ef..000000000000
--- a/Documentation/devicetree/bindings/gpio/gpio-nmk.txt
+++ /dev/null
@@ -1,31 +0,0 @@
-Nomadik GPIO controller
-
-Required properties:
-- compatible            : Should be "st,nomadik-gpio".
-- reg                   : Physical base address and length of the controller's registers.
-- interrupts            : The interrupt outputs from the controller.
-- #gpio-cells           : Should be two:
-                            The first cell is the pin number.
-                            The second cell is used to specify optional parameters:
-                              - bits[3:0] trigger type and level flags:
-                                  1 = low-to-high edge triggered.
-                                  2 = high-to-low edge triggered.
-                                  4 = active high level-sensitive.
-                                  8 = active low level-sensitive.
-- gpio-controller       : Marks the device node as a GPIO controller.
-- interrupt-controller  : Marks the device node as an interrupt controller.
-- gpio-bank             : Specifies which bank a controller owns.
-- st,supports-sleepmode : Specifies whether controller can sleep or not
-
-Example:
-
-                gpio1: gpio@8012e080 {
-                        compatible = "st,nomadik-gpio";
-                        reg =  <0x8012e080 0x80>;
-                        interrupts = <0 120 0x4>;
-                        #gpio-cells = <2>;
-                        gpio-controller;
-                        interrupt-controller;
-                        st,supports-sleepmode;
-                        gpio-bank = <1>;
-                };
diff --git a/Documentation/devicetree/bindings/gpio/st,nomadik-gpio.yaml b/Documentation/devicetree/bindings/gpio/st,nomadik-gpio.yaml
new file mode 100644
index 000000000000..38d37d8f7201
--- /dev/null
+++ b/Documentation/devicetree/bindings/gpio/st,nomadik-gpio.yaml
@@ -0,0 +1,95 @@
+# SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause)
+%YAML 1.2
+---
+$id: http://devicetree.org/schemas/gpio/st,nomadik-gpio.yaml#
+$schema: http://devicetree.org/meta-schemas/core.yaml#
+
+title: Nomadik GPIO controller
+
+description:
+  The Nomadik GPIO driver handles Nomadik SoC GPIO blocks. This block has also
+  been called ST STA2X11. On the Nomadik platform, this driver is intertwined
+  with pinctrl-nomadik.
+
+maintainers:
+  - Linus Walleij <linus.walleij@linaro.org>
+
+properties:
+  $nodename:
+    pattern: "^gpio@[0-9a-f]+$"
+
+  compatible:
+    enum:
+      - st,nomadik-gpio
+      - mobileye,eyeq5-gpio
+
+  reg:
+    maxItems: 1
+
+  interrupts:
+    maxItems: 1
+
+  "#gpio-cells":
+    const: 2
+
+  gpio-controller: true
+
+  interrupt-controller: true
+
+  "#interrupt-cells":
+    const: 2
+
+  gpio-bank:
+    description: System-wide GPIO bank index.
+    $ref: /schemas/types.yaml#/definitions/uint32
+
+  st,supports-sleepmode:
+    description: Whether the controller can sleep or not.
+    $ref: /schemas/types.yaml#/definitions/flag
+
+  clocks:
+    maxItems: 1
+
+  gpio-ranges:
+    maxItems: 1
+
+  ngpios:
+    minimum: 0
+    maximum: 32
+
+  resets:
+    maxItems: 1
+
+required:
+  - compatible
+  - reg
+  - interrupts
+  - "#gpio-cells"
+  - gpio-controller
+  - interrupt-controller
+  - gpio-bank
+
+unevaluatedProperties: false
+
+allOf:
+  - if:
+      properties:
+        compatible:
+          contains:
+            const: mobileye,eyeq5-gpio
+    then:
+      properties:
+        st,supports-sleepmode: false
+
+examples:
+  - |
+    gpio@8012e080 {
+        compatible = "st,nomadik-gpio";
+        reg =  <0x8012e080 0x80>;
+        interrupts = <0 120 0x4>;
+        #gpio-cells = <2>;
+        gpio-controller;
+        interrupt-controller;
+        st,supports-sleepmode;
+        gpio-bank = <1>;
+    };
diff --git a/Documentation/devicetree/bindings/pinctrl/amlogic,meson-pinctrl-a1.yaml b/Documentation/devicetree/bindings/pinctrl/amlogic,meson-pinctrl-a1.yaml
index c7df4cd34197..d9e0b2c48e84 100644
--- a/Documentation/devicetree/bindings/pinctrl/amlogic,meson-pinctrl-a1.yaml
+++ b/Documentation/devicetree/bindings/pinctrl/amlogic,meson-pinctrl-a1.yaml
@@ -24,7 +24,7 @@ required:
   - compatible
 
 patternProperties:
-  "^bank@[0-9a-z]+$":
+  "^bank@[0-9a-f]+$":
     $ref: amlogic,meson-pinctrl-common.yaml#/$defs/meson-gpio
 
     unevaluatedProperties: false
diff --git a/Documentation/devicetree/bindings/pinctrl/amlogic,meson-pinctrl-g12a-aobus.yaml b/Documentation/devicetree/bindings/pinctrl/amlogic,meson-pinctrl-g12a-aobus.yaml
index 0942ea60c6cd..108719bde0d0 100644
--- a/Documentation/devicetree/bindings/pinctrl/amlogic,meson-pinctrl-g12a-aobus.yaml
+++ b/Documentation/devicetree/bindings/pinctrl/amlogic,meson-pinctrl-g12a-aobus.yaml
@@ -21,7 +21,7 @@ required:
   - compatible
 
 patternProperties:
-  "^bank@[0-9a-z]+$":
+  "^bank@[0-9a-f]+$":
     $ref: amlogic,meson-pinctrl-common.yaml#/$defs/meson-gpio
 
     unevaluatedProperties: false
diff --git a/Documentation/devicetree/bindings/pinctrl/amlogic,meson-pinctrl-g12a-periphs.yaml b/Documentation/devicetree/bindings/pinctrl/amlogic,meson-pinctrl-g12a-periphs.yaml
index e3c8bde30559..dc277f2e2edf 100644
--- a/Documentation/devicetree/bindings/pinctrl/amlogic,meson-pinctrl-g12a-periphs.yaml
+++ b/Documentation/devicetree/bindings/pinctrl/amlogic,meson-pinctrl-g12a-periphs.yaml
@@ -21,7 +21,7 @@ required:
   - compatible
 
 patternProperties:
-  "^bank@[0-9a-z]+$":
+  "^bank@[0-9a-f]+$":
     $ref: amlogic,meson-pinctrl-common.yaml#/$defs/meson-gpio
 
     unevaluatedProperties: false
diff --git a/Documentation/devicetree/bindings/pinctrl/amlogic,meson8-pinctrl-aobus.yaml b/Documentation/devicetree/bindings/pinctrl/amlogic,meson8-pinctrl-aobus.yaml
index c1b03147e8ec..add83c676327 100644
--- a/Documentation/devicetree/bindings/pinctrl/amlogic,meson8-pinctrl-aobus.yaml
+++ b/Documentation/devicetree/bindings/pinctrl/amlogic,meson8-pinctrl-aobus.yaml
@@ -29,7 +29,7 @@ required:
   - compatible
 
 patternProperties:
-  "^bank@[0-9a-z]+$":
+  "^bank@[0-9a-f]+$":
     $ref: amlogic,meson-pinctrl-common.yaml#/$defs/meson-gpio
 
     unevaluatedProperties: false
diff --git a/Documentation/devicetree/bindings/pinctrl/amlogic,meson8-pinctrl-cbus.yaml b/Documentation/devicetree/bindings/pinctrl/amlogic,meson8-pinctrl-cbus.yaml
index 4ec85b8248fa..412bbcc276f3 100644
--- a/Documentation/devicetree/bindings/pinctrl/amlogic,meson8-pinctrl-cbus.yaml
+++ b/Documentation/devicetree/bindings/pinctrl/amlogic,meson8-pinctrl-cbus.yaml
@@ -29,7 +29,7 @@ required:
   - compatible
 
 patternProperties:
-  "^bank@[0-9a-z]+$":
+  "^bank@[0-9a-f]+$":
     $ref: amlogic,meson-pinctrl-common.yaml#/$defs/meson-gpio
 
     unevaluatedProperties: false
diff --git a/Documentation/devicetree/bindings/pinctrl/atmel,at91-pinctrl.txt b/Documentation/devicetree/bindings/pinctrl/atmel,at91-pinctrl.txt
index e8abbdad7b5d..0aa1a53012d6 100644
--- a/Documentation/devicetree/bindings/pinctrl/atmel,at91-pinctrl.txt
+++ b/Documentation/devicetree/bindings/pinctrl/atmel,at91-pinctrl.txt
@@ -20,6 +20,7 @@ such as pull-up, multi drive, etc.
 Required properties for iomux controller:
 - compatible: "atmel,at91rm9200-pinctrl" or "atmel,at91sam9x5-pinctrl"
 		or "atmel,sama5d3-pinctrl" or "microchip,sam9x60-pinctrl"
+		or "microchip,sam9x7-pinctrl", "microchip,sam9x60-pinctrl"
 - atmel,mux-mask: array of mask (periph per bank) to describe if a pin can be
   configured in this periph mode. All the periph and bank need to be describe.
 
@@ -120,6 +121,7 @@ Some requirements for using atmel,at91rm9200-pinctrl binding:
 For each bank the required properties are:
 - compatible: "atmel,at91sam9x5-gpio" or "atmel,at91rm9200-gpio" or
   "microchip,sam9x60-gpio"
+  or "microchip,sam9x7-gpio", "microchip,sam9x60-gpio", "atmel,at91rm9200-gpio"
 - reg: physical base address and length of the controller's registers
 - interrupts: interrupt outputs from the controller
 - interrupt-controller: marks the device node as an interrupt controller
diff --git a/Documentation/devicetree/bindings/pinctrl/awinic,aw9523-pinctrl.yaml b/Documentation/devicetree/bindings/pinctrl/awinic,aw9523-pinctrl.yaml
new file mode 100644
index 000000000000..98c310a3c63c
--- /dev/null
+++ b/Documentation/devicetree/bindings/pinctrl/awinic,aw9523-pinctrl.yaml
@@ -0,0 +1,139 @@
+# SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause)
+%YAML 1.2
+---
+$id: http://devicetree.org/schemas/pinctrl/awinic,aw9523-pinctrl.yaml#
+$schema: http://devicetree.org/meta-schemas/core.yaml#
+
+title: Awinic AW9523/AW9523B I2C GPIO Expander
+
+maintainers:
+  - AngeloGioacchino Del Regno <angelogioacchino.delregno@somainline.org>
+
+description: |
+  The Awinic AW9523/AW9523B I2C GPIO Expander featuring 16 multi-function
+  I/O, 256 steps PWM mode and interrupt support.
+
+properties:
+  compatible:
+    const: awinic,aw9523-pinctrl
+
+  reg:
+    maxItems: 1
+
+  '#gpio-cells':
+    description: |
+      Specifying the pin number and flags, as defined in
+      include/dt-bindings/gpio/gpio.h
+    const: 2
+
+  gpio-controller: true
+
+  gpio-ranges:
+    maxItems: 1
+
+  interrupt-controller: true
+
+  interrupts:
+    maxItems: 1
+    description: Specifies the INTN pin IRQ.
+
+  '#interrupt-cells':
+    description:
+      Specifies the PIN numbers and Flags, as defined in defined in
+      include/dt-bindings/interrupt-controller/irq.h
+    const: 2
+
+  reset-gpios:
+    maxItems: 1
+
+# PIN CONFIGURATION NODES
+patternProperties:
+  '-pins$':
+    type: object
+    description:
+      Pinctrl node's client devices use subnodes for desired pin configuration.
+      Client device subnodes use below standard properties.
+    $ref: /schemas/pinctrl/pincfg-node.yaml
+
+    properties:
+      pins:
+        description:
+          List of gpio pins affected by the properties specified in
+          this subnode.
+        items:
+          pattern: "^gpio([0-9]|1[0-5])$"
+        minItems: 1
+        maxItems: 16
+
+      function:
+        description:
+          Specify the alternative function to be configured for the
+          specified pins.
+
+        enum: [ gpio, pwm ]
+
+      bias-disable: true
+      bias-pull-down: true
+      bias-pull-up: true
+      drive-open-drain: true
+      drive-push-pull: true
+      input-enable: true
+      input-disable: true
+      output-high: true
+      output-low: true
+
+    required:
+      - pins
+      - function
+
+    additionalProperties: false
+
+required:
+  - compatible
+  - reg
+  - gpio-controller
+  - '#gpio-cells'
+  - gpio-ranges
+
+additionalProperties: false
+
+examples:
+  # Example configuration to drive pins for a keyboard matrix
+  - |
+    #include <dt-bindings/gpio/gpio.h>
+    #include <dt-bindings/interrupt-controller/irq.h>
+
+    i2c {
+        #address-cells = <1>;
+        #size-cells = <0>;
+
+        aw9523: gpio-expander@58 {
+                compatible = "awinic,aw9523-pinctrl";
+                reg = <0x58>;
+                interrupt-parent = <&tlmm>;
+                interrupts = <50 IRQ_TYPE_EDGE_FALLING>;
+                gpio-controller;
+                #gpio-cells = <2>;
+                gpio-ranges = <&tlmm 0 0 16>;
+                interrupt-controller;
+                #interrupt-cells = <2>;
+                reset-gpios = <&tlmm 51 GPIO_ACTIVE_HIGH>;
+
+                keyboard-matrix-col-pins {
+                        pins = "gpio8", "gpio9", "gpio10", "gpio11",
+                               "gpio12", "gpio13", "gpio14", "gpio15";
+                        function = "gpio";
+                        input-disable;
+                        output-low;
+                };
+
+                keyboard-matrix-row-pins {
+                        pins = "gpio0", "gpio1", "gpio2", "gpio3",
+                               "gpio4", "gpio5", "gpio6", "gpio7";
+                        function = "gpio";
+                        bias-pull-up;
+                        drive-open-drain;
+                        input-enable;
+                };
+        };
+    };
diff --git a/Documentation/devicetree/bindings/pinctrl/cirrus,madera.yaml b/Documentation/devicetree/bindings/pinctrl/cirrus,madera.yaml
index bb61a30321a1..482acda88e73 100644
--- a/Documentation/devicetree/bindings/pinctrl/cirrus,madera.yaml
+++ b/Documentation/devicetree/bindings/pinctrl/cirrus,madera.yaml
@@ -93,7 +93,8 @@ properties:
 
           input-schmitt-disable: true
 
-          input-debounce: true
+          input-debounce:
+            maxItems: 1
 
           output-low: true
 
diff --git a/Documentation/devicetree/bindings/pinctrl/cypress,cy8c95x0.yaml b/Documentation/devicetree/bindings/pinctrl/cypress,cy8c95x0.yaml
index 7f30ec2f1e54..700ac86c26b6 100644
--- a/Documentation/devicetree/bindings/pinctrl/cypress,cy8c95x0.yaml
+++ b/Documentation/devicetree/bindings/pinctrl/cypress,cy8c95x0.yaml
@@ -45,7 +45,8 @@ properties:
     maxItems: 1
 
   gpio-reserved-ranges:
-    maxItems: 1
+    minItems: 1
+    maxItems: 60
 
   vdd-supply:
     description:
@@ -85,6 +86,8 @@ patternProperties:
 
       bias-disable: true
 
+      input-enable: true
+
       output-high: true
 
       output-low: true
@@ -133,6 +136,23 @@ examples:
         interrupts = <GIC_SPI 94 IRQ_TYPE_LEVEL_HIGH>;
         interrupt-controller;
         vdd-supply = <&p3v3>;
-        gpio-reserved-ranges = <5 1>;
+        gpio-reserved-ranges = <1 2>, <6 1>, <10 1>, <15 1>;
+
+        pinctrl-0 = <&U62160_pins>, <&U62160_ipins>;
+        pinctrl-names = "default";
+
+        U62160_pins: cfg-pins {
+          pins = "gp03", "gp16", "gp20", "gp50", "gp51";
+          function = "gpio";
+          input-enable;
+          bias-pull-up;
+        };
+
+        U62160_ipins: icfg-pins {
+          pins = "gp04", "gp17", "gp21", "gp52", "gp53";
+          function = "gpio";
+          input-enable;
+          bias-pull-up;
+        };
       };
     };
diff --git a/Documentation/devicetree/bindings/pinctrl/mobileye,eyeq5-pinctrl.yaml b/Documentation/devicetree/bindings/pinctrl/mobileye,eyeq5-pinctrl.yaml
new file mode 100644
index 000000000000..5f00604bf48c
--- /dev/null
+++ b/Documentation/devicetree/bindings/pinctrl/mobileye,eyeq5-pinctrl.yaml
@@ -0,0 +1,242 @@
+# SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause)
+%YAML 1.2
+---
+$id: http://devicetree.org/schemas/pinctrl/mobileye,eyeq5-pinctrl.yaml#
+$schema: http://devicetree.org/meta-schemas/core.yaml#
+
+title: Mobileye EyeQ5 pin controller
+
+description: >
+  The EyeQ5 pin controller handles the two pin banks of the system. It belongs
+  to a system-controller block called OLB.
+
+  Pin control is about bias (pull-down, pull-up), drive strength and muxing. Pin
+  muxing supports two functions for each pin: first is GPIO, second is
+  pin-dependent.
+
+  Pins and groups are bijective.
+
+maintainers:
+  - Grégory Clement <gregory.clement@bootlin.com>
+  - Théo Lebrun <theo.lebrun@bootlin.com>
+  - Vladimir Kondratiev <vladimir.kondratiev@mobileye.com>
+
+$ref: pinctrl.yaml#
+
+properties:
+  compatible:
+    enum:
+      - mobileye,eyeq5-pinctrl
+
+  reg:
+    maxItems: 1
+
+patternProperties:
+  "-pins?$":
+    type: object
+    description: Pin muxing configuration.
+    $ref: pinmux-node.yaml#
+    additionalProperties: false
+    properties:
+      pins: true
+      function:
+        enum: [gpio,
+               # Bank A
+               timer0, timer1, timer2, timer5, uart0, uart1, can0, can1, spi0,
+               spi1, refclk0,
+               # Bank B
+               timer3, timer4, timer6, uart2, can2, spi2, spi3, mclk0]
+      bias-disable: true
+      bias-pull-down: true
+      bias-pull-up: true
+      drive-strength: true
+    required:
+      - pins
+      - function
+    allOf:
+      - if:
+          properties:
+            function:
+              const: gpio
+        then:
+          properties:
+            pins:
+              items: # PA0 - PA28, PB0 - PB22
+                pattern: '^(P(A|B)1?[0-9]|PA2[0-8]|PB2[0-2])$'
+      - if:
+          properties:
+            function:
+              const: timer0
+        then:
+          properties:
+            pins:
+              items:
+                enum: [PA0, PA1]
+      - if:
+          properties:
+            function:
+              const: timer1
+        then:
+          properties:
+            pins:
+              items:
+                enum: [PA2, PA3]
+      - if:
+          properties:
+            function:
+              const: timer2
+        then:
+          properties:
+            pins:
+              items:
+                enum: [PA4, PA5]
+      - if:
+          properties:
+            function:
+              const: timer5
+        then:
+          properties:
+            pins:
+              items:
+                enum: [PA6, PA7, PA8, PA9]
+      - if:
+          properties:
+            function:
+              const: uart0
+        then:
+          properties:
+            pins:
+              items:
+                enum: [PA10, PA11]
+      - if:
+          properties:
+            function:
+              const: uart1
+        then:
+          properties:
+            pins:
+              items:
+                enum: [PA12, PA13]
+      - if:
+          properties:
+            function:
+              const: can0
+        then:
+          properties:
+            pins:
+              items:
+                enum: [PA14, PA15]
+      - if:
+          properties:
+            function:
+              const: can1
+        then:
+          properties:
+            pins:
+              items:
+                enum: [PA16, PA17]
+      - if:
+          properties:
+            function:
+              const: spi0
+        then:
+          properties:
+            pins:
+              items:
+                enum: [PA18, PA19, PA20, PA21, PA22]
+      - if:
+          properties:
+            function:
+              const: spi1
+        then:
+          properties:
+            pins:
+              items:
+                enum: [PA23, PA24, PA25, PA26, PA27]
+      - if:
+          properties:
+            function:
+              const: refclk0
+        then:
+          properties:
+            pins:
+              items:
+                enum: [PA28]
+      - if:
+          properties:
+            function:
+              const: timer3
+        then:
+          properties:
+            pins:
+              items:
+                enum: [PB0, PB1]
+      - if:
+          properties:
+            function:
+              const: timer4
+        then:
+          properties:
+            pins:
+              items:
+                enum: [PB2, PB3]
+      - if:
+          properties:
+            function:
+              const: timer6
+        then:
+          properties:
+            pins:
+              items:
+                enum: [PB4, PB5, PB6, PB7]
+      - if:
+          properties:
+            function:
+              const: uart2
+        then:
+          properties:
+            pins:
+              items:
+                enum: [PB8, PB9]
+      - if:
+          properties:
+            function:
+              const: can2
+        then:
+          properties:
+            pins:
+              items:
+                enum: [PB10, PB11]
+      - if:
+          properties:
+            function:
+              const: spi2
+        then:
+          properties:
+            pins:
+              items:
+                enum: [PB12, PB13, PB14, PB15, PB16]
+      - if:
+          properties:
+            function:
+              const: spi3
+        then:
+          properties:
+            pins:
+              items:
+                enum: [PB17, PB18, PB19, PB20, PB21]
+      - if:
+          properties:
+            function:
+              const: mclk0
+        then:
+          properties:
+            pins:
+              items:
+                enum: [PB22]
+
+required:
+  - compatible
+  - reg
+
+additionalProperties: false
diff --git a/Documentation/devicetree/bindings/pinctrl/nuvoton,npcm845-pinctrl.yaml b/Documentation/devicetree/bindings/pinctrl/nuvoton,npcm845-pinctrl.yaml
index 3e8472898800..b55d9c316659 100644
--- a/Documentation/devicetree/bindings/pinctrl/nuvoton,npcm845-pinctrl.yaml
+++ b/Documentation/devicetree/bindings/pinctrl/nuvoton,npcm845-pinctrl.yaml
@@ -152,7 +152,6 @@ patternProperties:
         description:
           Debouncing periods in microseconds, one period per interrupt
           bank found in the controller
-        $ref: /schemas/types.yaml#/definitions/uint32-array
         minItems: 1
         maxItems: 4
 
@@ -160,7 +159,6 @@ patternProperties:
         description: |
           0: Low rate
           1: High rate
-        $ref: /schemas/types.yaml#/definitions/uint32
         enum: [0, 1]
 
       drive-strength:
diff --git a/Documentation/devicetree/bindings/pinctrl/nuvoton,wpcm450-pinctrl.yaml b/Documentation/devicetree/bindings/pinctrl/nuvoton,wpcm450-pinctrl.yaml
index 7b7f840ffc4c..08442c880f07 100644
--- a/Documentation/devicetree/bindings/pinctrl/nuvoton,wpcm450-pinctrl.yaml
+++ b/Documentation/devicetree/bindings/pinctrl/nuvoton,wpcm450-pinctrl.yaml
@@ -103,7 +103,8 @@ patternProperties:
         items:
           pattern: "^gpio1?[0-9]{1,2}$"
 
-      input-debounce: true
+      input-debounce:
+        maxItems: 1
 
     additionalProperties: false
 
diff --git a/Documentation/devicetree/bindings/pinctrl/nvidia,tegra234-pinmux-aon.yaml b/Documentation/devicetree/bindings/pinctrl/nvidia,tegra234-pinmux-aon.yaml
index f3deda9f7127..db8224dfba2c 100644
--- a/Documentation/devicetree/bindings/pinctrl/nvidia,tegra234-pinmux-aon.yaml
+++ b/Documentation/devicetree/bindings/pinctrl/nvidia,tegra234-pinmux-aon.yaml
@@ -10,18 +10,21 @@ maintainers:
   - Thierry Reding <thierry.reding@gmail.com>
   - Jon Hunter <jonathanh@nvidia.com>
 
-$ref: nvidia,tegra234-pinmux-common.yaml
-
 properties:
   compatible:
     const: nvidia,tegra234-pinmux-aon
 
+  reg:
+    maxItems: 1
+
 patternProperties:
   "^pinmux(-[a-z0-9-]+)?$":
     type: object
 
     # pin groups
     additionalProperties:
+      $ref: nvidia,tegra234-pinmux-common.yaml
+
       properties:
         nvidia,pins:
           items:
diff --git a/Documentation/devicetree/bindings/pinctrl/nvidia,tegra234-pinmux-common.yaml b/Documentation/devicetree/bindings/pinctrl/nvidia,tegra234-pinmux-common.yaml
index 4f9de78085e5..8cf9e4c915ff 100644
--- a/Documentation/devicetree/bindings/pinctrl/nvidia,tegra234-pinmux-common.yaml
+++ b/Documentation/devicetree/bindings/pinctrl/nvidia,tegra234-pinmux-common.yaml
@@ -10,57 +10,43 @@ maintainers:
   - Thierry Reding <thierry.reding@gmail.com>
   - Jon Hunter <jonathanh@nvidia.com>
 
-properties:
-  reg:
-    items:
-      - description: pinmux registers
-
-patternProperties:
-  "^pinmux(-[a-z0-9-]+)?$":
-    type: object
-
-    # pin groups
-    additionalProperties:
-      $ref: nvidia,tegra-pinmux-common.yaml
-      # We would typically use unevaluatedProperties here but that has the
-      # downside that all the properties in the common bindings become valid
-      # for all chip generations. In this case, however, we want the per-SoC
-      # bindings to be able to override which of the common properties are
-      # allowed, since not all pinmux generations support the same sets of
-      # properties. This way, the common bindings define the format of the
-      # properties but the per-SoC bindings define which of them apply to a
-      # given chip.
-      additionalProperties: false
-      properties:
-        nvidia,function:
-          enum: [ gp, uartc, i2c8, spi2, i2c2, can1, can0, rsvd0, eth0, eth2,
-                  eth1, dp, eth3, i2c4, i2c7, i2c9, eqos, pe2, pe1, pe0, pe3,
-                  pe4, pe5, pe6, pe7, pe8, pe9, pe10, qspi0, qspi1, qpsi,
-                  sdmmc1, sce, soc, gpio, hdmi, ufs0, spi3, spi1, uartb, uarte,
-                  usb, extperiph2, extperiph1, i2c3, vi0, i2c5, uarta, uartd,
-                  i2c1, i2s4, i2s6, aud, spi5, touch, uartj, rsvd1, wdt, tsc,
-                  dmic3, led, vi0_alt, i2s5, nv, extperiph3, extperiph4, spi4,
-                  ccla, i2s1, i2s2, i2s3, i2s8, rsvd2, dmic5, dca, displayb,
-                  displaya, vi1, dcb, dmic1, dmic4, i2s7, dmic2, dspk0, rsvd3,
-                  tsc_alt, istctrl, vi1_alt, dspk1, igpu ]
+$ref: nvidia,tegra-pinmux-common.yaml
 
-        # out of the common properties, only these are allowed for Tegra234
-        nvidia,pins: true
-        nvidia,pull: true
-        nvidia,tristate: true
-        nvidia,schmitt: true
-        nvidia,enable-input: true
-        nvidia,open-drain: true
-        nvidia,lock: true
-        nvidia,drive-type: true
-        nvidia,io-hv: true
-
-      required:
-        - nvidia,pins
+properties:
+  nvidia,function:
+    enum: [ gp, uartc, i2c8, spi2, i2c2, can1, can0, rsvd0, eth0, eth2,
+            eth1, dp, eth3, i2c4, i2c7, i2c9, eqos, pe2, pe1, pe0, pe3,
+            pe4, pe5, pe6, pe7, pe8, pe9, pe10, qspi0, qspi1, qpsi,
+            sdmmc1, sce, soc, gpio, hdmi, ufs0, spi3, spi1, uartb, uarte,
+            usb, extperiph2, extperiph1, i2c3, vi0, i2c5, uarta, uartd,
+            i2c1, i2s4, i2s6, aud, spi5, touch, uartj, rsvd1, wdt, tsc,
+            dmic3, led, vi0_alt, i2s5, nv, extperiph3, extperiph4, spi4,
+            ccla, i2s1, i2s2, i2s3, i2s8, rsvd2, dmic5, dca, displayb,
+            displaya, vi1, dcb, dmic1, dmic4, i2s7, dmic2, dspk0, rsvd3,
+            tsc_alt, istctrl, vi1_alt, dspk1, igpu ]
+
+  # out of the common properties, only these are allowed for Tegra234
+  nvidia,pins: true
+  nvidia,pull: true
+  nvidia,tristate: true
+  nvidia,schmitt: true
+  nvidia,enable-input: true
+  nvidia,open-drain: true
+  nvidia,lock: true
+  nvidia,drive-type: true
+  nvidia,io-hv: true
 
 required:
-  - compatible
-  - reg
+  - nvidia,pins
+
+# We would typically use unevaluatedProperties here but that has the
+# downside that all the properties in the common bindings become valid
+# for all chip generations. In this case, however, we want the per-SoC
+# bindings to be able to override which of the common properties are
+# allowed, since not all pinmux generations support the same sets of
+# properties. This way, the common bindings define the format of the
+# properties but the per-SoC bindings define which of them apply to a
+# given chip.
+additionalProperties: false
 
-additionalProperties: true
 ...
diff --git a/Documentation/devicetree/bindings/pinctrl/nvidia,tegra234-pinmux.yaml b/Documentation/devicetree/bindings/pinctrl/nvidia,tegra234-pinmux.yaml
index 17b865ecfcda..f5a3a881dec4 100644
--- a/Documentation/devicetree/bindings/pinctrl/nvidia,tegra234-pinmux.yaml
+++ b/Documentation/devicetree/bindings/pinctrl/nvidia,tegra234-pinmux.yaml
@@ -10,18 +10,21 @@ maintainers:
   - Thierry Reding <thierry.reding@gmail.com>
   - Jon Hunter <jonathanh@nvidia.com>
 
-$ref: nvidia,tegra234-pinmux-common.yaml
-
 properties:
   compatible:
     const: nvidia,tegra234-pinmux
 
+  reg:
+    maxItems: 1
+
 patternProperties:
   "^pinmux(-[a-z0-9-]+)?$":
     type: object
 
     # pin groups
     additionalProperties:
+      $ref: nvidia,tegra234-pinmux-common.yaml
+
       properties:
         nvidia,pins:
           items:
diff --git a/Documentation/devicetree/bindings/pinctrl/pincfg-node.yaml b/Documentation/devicetree/bindings/pinctrl/pincfg-node.yaml
index be81ed22a036..d0af21a564b4 100644
--- a/Documentation/devicetree/bindings/pinctrl/pincfg-node.yaml
+++ b/Documentation/devicetree/bindings/pinctrl/pincfg-node.yaml
@@ -97,7 +97,7 @@ properties:
     description: disable schmitt-trigger mode
 
   input-debounce:
-    $ref: /schemas/types.yaml#/definitions/uint32
+    $ref: /schemas/types.yaml#/definitions/uint32-array
     description: Takes the debounce time in usec as argument or 0 to disable
       debouncing
 
diff --git a/Documentation/devicetree/bindings/pinctrl/qcom,sm4450-tlmm.yaml b/Documentation/devicetree/bindings/pinctrl/qcom,sm4450-tlmm.yaml
index bb08ca5a1509..bb675c8ec220 100644
--- a/Documentation/devicetree/bindings/pinctrl/qcom,sm4450-tlmm.yaml
+++ b/Documentation/devicetree/bindings/pinctrl/qcom,sm4450-tlmm.yaml
@@ -17,7 +17,7 @@ allOf:
 
 properties:
   compatible:
-    const: qcom,sm4450-pinctrl
+    const: qcom,sm4450-tlmm
 
   reg:
     maxItems: 1
diff --git a/Documentation/devicetree/bindings/pinctrl/renesas,pfc.yaml b/Documentation/devicetree/bindings/pinctrl/renesas,pfc.yaml
index 181cd1676c0a..5d84364d1358 100644
--- a/Documentation/devicetree/bindings/pinctrl/renesas,pfc.yaml
+++ b/Documentation/devicetree/bindings/pinctrl/renesas,pfc.yaml
@@ -46,6 +46,7 @@ properties:
       - renesas,pfc-r8a779a0    # R-Car V3U
       - renesas,pfc-r8a779f0    # R-Car S4-8
       - renesas,pfc-r8a779g0    # R-Car V4H
+      - renesas,pfc-r8a779h0    # R-Car V4M
       - renesas,pfc-sh73a0      # SH-Mobile AG5
 
   reg:
diff --git a/Documentation/devicetree/bindings/pinctrl/xlnx,zynq-pinctrl.yaml b/Documentation/devicetree/bindings/pinctrl/xlnx,pinctrl-zynq.yaml
index d2676f92ef5b..de6c10ba36c4 100644
--- a/Documentation/devicetree/bindings/pinctrl/xlnx,zynq-pinctrl.yaml
+++ b/Documentation/devicetree/bindings/pinctrl/xlnx,pinctrl-zynq.yaml
@@ -1,7 +1,7 @@
 # SPDX-License-Identifier: GPL-2.0-only OR BSD-2-Clause
 %YAML 1.2
 ---
-$id: http://devicetree.org/schemas/pinctrl/xlnx,zynq-pinctrl.yaml#
+$id: http://devicetree.org/schemas/pinctrl/xlnx,pinctrl-zynq.yaml#
 $schema: http://devicetree.org/meta-schemas/core.yaml#
 
 title: Xilinx Zynq Pinctrl
@@ -28,7 +28,7 @@ description: |
 
 properties:
   compatible:
-    const: xlnx,zynq-pinctrl
+    const: xlnx,pinctrl-zynq
 
   reg:
     description: Specifies the base address and size of the SLCR space.
@@ -181,7 +181,7 @@ examples:
   - |
     #include <dt-bindings/pinctrl/pinctrl-zynq.h>
     pinctrl0: pinctrl@700 {
-       compatible = "xlnx,zynq-pinctrl";
+       compatible = "xlnx,pinctrl-zynq";
        reg = <0x700 0x200>;
        syscon = <&slcr>;