Merge tag 'pci-v4.12-changes' of git://git.kernel.org/pub/scm/linux/kernel/git/helgaas/pci

Pull PCI updates from Bjorn Helgaas:

 - add framework for supporting PCIe devices in Endpoint mode (Kishon
   Vijay Abraham I)

 - use non-postable PCI config space mappings when possible (Lorenzo
   Pieralisi)

 - clean up and unify mmap of PCI BARs (David Woodhouse)

 - export and unify Function Level Reset support (Christoph Hellwig)

 - avoid FLR for Intel 82579 NICs (Sasha Neftin)

 - add pci_request_irq() and pci_free_irq() helpers (Christoph Hellwig)

 - short-circuit config access failures for disconnected devices (Keith
   Busch)

 - remove D3 sleep delay when possible (Adrian Hunter)

 - freeze PME scan before suspending devices (Lukas Wunner)

 - stop disabling MSI/MSI-X in pci_device_shutdown() (Prarit Bhargava)

 - disable boot interrupt quirk for ASUS M2N-LR (Stefan Assmann)

 - add arch-specific alignment control to improve device passthrough by
   avoiding multiple BARs in a page (Yongji Xie)

 - add sysfs sriov_drivers_autoprobe to control VF driver binding
   (Bodong Wang)

 - allow slots below PCI-to-PCIe "reverse bridges" (Bjorn Helgaas)

 - fix crashes when unbinding host controllers that don't support
   removal (Brian Norris)

 - add driver for MicroSemi Switchtec management interface (Logan
   Gunthorpe)

 - add driver for Faraday Technology FTPCI100 host bridge (Linus
   Walleij)

 - add i.MX7D support (Andrey Smirnov)

 - use generic MSI support for Aardvark (Thomas Petazzoni)

 - make Rockchip driver modular (Brian Norris)

 - advertise 128-byte Read Completion Boundary support for Rockchip
   (Shawn Lin)

 - advertise PCI_EXP_LNKSTA_SLC for Rockchip root port (Shawn Lin)

 - convert atomic_t to refcount_t in HV driver (Elena Reshetova)

 - add CPU IRQ affinity in HV driver (K. Y. Srinivasan)

 - fix PCI bus removal in HV driver (Long Li)

 - add support for ThunderX2 DMA alias topology (Jayachandran C)

 - add ThunderX pass2.x 2nd node MCFG quirk (Tomasz Nowicki)

 - add ITE 8893 bridge DMA alias quirk (Jarod Wilson)

 - restrict Cavium ACS quirk only to CN81xx/CN83xx/CN88xx devices
   (Manish Jaggi)

* tag 'pci-v4.12-changes' of git://git.kernel.org/pub/scm/linux/kernel/git/helgaas/pci: (146 commits)
  PCI: Don't allow unbinding host controllers that aren't prepared
  ARM: DRA7: clockdomain: Change the CLKTRCTRL of CM_PCIE_CLKSTCTRL to SW_WKUP
  MAINTAINERS: Add PCI Endpoint maintainer
  Documentation: PCI: Add userguide for PCI endpoint test function
  tools: PCI: Add sample test script to invoke pcitest
  tools: PCI: Add a userspace tool to test PCI endpoint
  Documentation: misc-devices: Add Documentation for pci-endpoint-test driver
  misc: Add host side PCI driver for PCI test function device
  PCI: Add device IDs for DRA74x and DRA72x
  dt-bindings: PCI: dra7xx: Add DT bindings to enable unaligned access
  PCI: dwc: dra7xx: Workaround for errata id i870
  dt-bindings: PCI: dra7xx: Add DT bindings for PCI dra7xx EP mode
  PCI: dwc: dra7xx: Add EP mode support
  PCI: dwc: dra7xx: Facilitate wrapper and MSI interrupts to be enabled independently
  dt-bindings: PCI: Add DT bindings for PCI designware EP mode
  PCI: dwc: designware: Add EP mode support
  Documentation: PCI: Add binding documentation for pci-test endpoint function
  ixgbe: Use pcie_flr() instead of duplicating it
  IB/hfi1: Use pcie_flr() instead of duplicating it
  PCI: imx6: Fix spelling mistake: "contol" -> "control"
  ...

4 files changed, 195 insertions, 16 deletions

diff --git a/Documentation/devicetree/bindings/pci/designware-pcie.txt b/Documentation/devicetree/bindings/pci/designware-pcie.txt
index 1392c705ceca..b2480dd38c11 100644
--- a/Documentation/devicetree/bindings/pci/designware-pcie.txt
+++ b/Documentation/devicetree/bindings/pci/designware-pcie.txt
@@ -6,30 +6,40 @@ Required properties:
 - reg-names: Must be "config" for the PCIe configuration space.
     (The old way of getting the configuration address space from "ranges"
     is deprecated and should be avoided.)
+- num-lanes: number of lanes to use
+RC mode:
 - #address-cells: set to <3>
 - #size-cells: set to <2>
 - device_type: set to "pci"
 - ranges: ranges for the PCI memory and I/O regions
 - #interrupt-cells: set to <1>
-- interrupt-map-mask and interrupt-map: standard PCI properties
-	to define the mapping of the PCIe interface to interrupt
+- interrupt-map-mask and interrupt-map: standard PCI
+	properties to define the mapping of the PCIe interface to interrupt
 	numbers.
-- num-lanes: number of lanes to use
+EP mode:
+- num-ib-windows: number of inbound address translation
+        windows
+- num-ob-windows: number of outbound address translation
+        windows
 
 Optional properties:
-- num-viewport: number of view ports configured in hardware.  If a platform
-  does not specify it, the driver assumes 2.
 - num-lanes: number of lanes to use (this property should be specified unless
   the link is brought already up in BIOS)
 - reset-gpio: gpio pin number of power good signal
-- bus-range: PCI bus numbers covered (it is recommended for new devicetrees to
-  specify this property, to keep backwards compatibility a range of 0x00-0xff
-  is assumed if not present)
 - clocks: Must contain an entry for each entry in clock-names.
 	See ../clocks/clock-bindings.txt for details.
 - clock-names: Must include the following entries:
 	- "pcie"
 	- "pcie_bus"
+RC mode:
+- num-viewport: number of view ports configured in
+  hardware. If a platform does not specify it, the driver assumes 2.
+- bus-range: PCI bus numbers covered (it is recommended
+  for new devicetrees to specify this property, to keep backwards
+  compatibility a range of 0x00-0xff is assumed if not present)
+EP mode:
+- max-functions: maximum number of functions that can be
+  configured
 
 Example configuration:
 
diff --git a/Documentation/devicetree/bindings/pci/faraday,ftpci100.txt b/Documentation/devicetree/bindings/pci/faraday,ftpci100.txt
new file mode 100644
index 000000000000..35d4a979bb7b
--- /dev/null
+++ b/Documentation/devicetree/bindings/pci/faraday,ftpci100.txt
@@ -0,0 +1,129 @@
+Faraday Technology FTPCI100 PCI Host Bridge
+
+This PCI bridge is found inside that Cortina Systems Gemini SoC platform and
+is a generic IP block from Faraday Technology. It exists in two variants:
+plain and dual PCI. The plain version embeds a cascading interrupt controller
+into the host bridge. The dual version routes the interrupts to the host
+chips interrupt controller.
+
+The host controller appear on the PCI bus with vendor ID 0x159b (Faraday
+Technology) and product ID 0x4321.
+
+Mandatory properties:
+
+- compatible: ranging from specific to generic, should be one of
+  "cortina,gemini-pci", "faraday,ftpci100"
+  "cortina,gemini-pci-dual", "faraday,ftpci100-dual"
+  "faraday,ftpci100"
+  "faraday,ftpci100-dual"
+- reg: memory base and size for the host bridge
+- #address-cells: set to <3>
+- #size-cells: set to <2>
+- #interrupt-cells: set to <1>
+- bus-range: set to <0x00 0xff>
+- device_type, set to "pci"
+- ranges: see pci.txt
+- interrupt-map-mask: see pci.txt
+- interrupt-map: see pci.txt
+- dma-ranges: three ranges for the inbound memory region. The ranges must
+  be aligned to a 1MB boundary, and may be 1MB, 2MB, 4MB, 8MB, 16MB, 32MB, 64MB,
+  128MB, 256MB, 512MB, 1GB or 2GB in size. The memory should be marked as
+  pre-fetchable.
+
+Mandatory subnodes:
+- For "faraday,ftpci100" a node representing the interrupt-controller inside the
+  host bridge is mandatory. It has the following mandatory properties:
+  - interrupt: see interrupt-controller/interrupts.txt
+  - interrupt-parent: see interrupt-controller/interrupts.txt
+  - interrupt-controller: see interrupt-controller/interrupts.txt
+  - #address-cells: set to <0>
+  - #interrupt-cells: set to <1>
+
+I/O space considerations:
+
+The plain variant has 128MiB of non-prefetchable memory space, whereas the
+"dual" variant has 64MiB. Take this into account when describing the ranges.
+
+Interrupt map considerations:
+
+The "dual" variant will get INT A, B, C, D from the system interrupt controller
+and should point to respective interrupt in that controller in its
+interrupt-map.
+
+The code which is the only documentation of how the Faraday PCI (the non-dual
+variant) interrupts assigns the default interrupt mapping/swizzling has
+typically been like this, doing the swizzling on the interrupt controller side
+rather than in the interconnect:
+
+interrupt-map-mask = <0xf800 0 0 7>;
+interrupt-map =
+	<0x4800 0 0 1 &pci_intc 0>, /* Slot 9 */
+	<0x4800 0 0 2 &pci_intc 1>,
+	<0x4800 0 0 3 &pci_intc 2>,
+	<0x4800 0 0 4 &pci_intc 3>,
+	<0x5000 0 0 1 &pci_intc 1>, /* Slot 10 */
+	<0x5000 0 0 2 &pci_intc 2>,
+	<0x5000 0 0 3 &pci_intc 3>,
+	<0x5000 0 0 4 &pci_intc 0>,
+	<0x5800 0 0 1 &pci_intc 2>, /* Slot 11 */
+	<0x5800 0 0 2 &pci_intc 3>,
+	<0x5800 0 0 3 &pci_intc 0>,
+	<0x5800 0 0 4 &pci_intc 1>,
+	<0x6000 0 0 1 &pci_intc 3>, /* Slot 12 */
+	<0x6000 0 0 2 &pci_intc 0>,
+	<0x6000 0 0 3 &pci_intc 1>,
+	<0x6000 0 0 4 &pci_intc 2>;
+
+Example:
+
+pci@50000000 {
+	compatible = "cortina,gemini-pci", "faraday,ftpci100";
+	reg = <0x50000000 0x100>;
+	interrupts = <8 IRQ_TYPE_LEVEL_HIGH>, /* PCI A */
+			<26 IRQ_TYPE_LEVEL_HIGH>, /* PCI B */
+			<27 IRQ_TYPE_LEVEL_HIGH>, /* PCI C */
+			<28 IRQ_TYPE_LEVEL_HIGH>; /* PCI D */
+	#address-cells = <3>;
+	#size-cells = <2>;
+	#interrupt-cells = <1>;
+
+	bus-range = <0x00 0xff>;
+	ranges = /* 1MiB I/O space 0x50000000-0x500fffff */
+		 <0x01000000 0 0          0x50000000 0 0x00100000>,
+		 /* 128MiB non-prefetchable memory 0x58000000-0x5fffffff */
+		 <0x02000000 0 0x58000000 0x58000000 0 0x08000000>;
+
+	/* DMA ranges */
+	dma-ranges =
+	/* 128MiB at 0x00000000-0x07ffffff */
+	<0x02000000 0 0x00000000 0x00000000 0 0x08000000>,
+	/* 64MiB at 0x00000000-0x03ffffff */
+	<0x02000000 0 0x00000000 0x00000000 0 0x04000000>,
+	/* 64MiB at 0x00000000-0x03ffffff */
+	<0x02000000 0 0x00000000 0x00000000 0 0x04000000>;
+
+	interrupt-map-mask = <0xf800 0 0 7>;
+	interrupt-map =
+		<0x4800 0 0 1 &pci_intc 0>, /* Slot 9 */
+		<0x4800 0 0 2 &pci_intc 1>,
+		<0x4800 0 0 3 &pci_intc 2>,
+		<0x4800 0 0 4 &pci_intc 3>,
+		<0x5000 0 0 1 &pci_intc 1>, /* Slot 10 */
+		<0x5000 0 0 2 &pci_intc 2>,
+		<0x5000 0 0 3 &pci_intc 3>,
+		<0x5000 0 0 4 &pci_intc 0>,
+		<0x5800 0 0 1 &pci_intc 2>, /* Slot 11 */
+		<0x5800 0 0 2 &pci_intc 3>,
+		<0x5800 0 0 3 &pci_intc 0>,
+		<0x5800 0 0 4 &pci_intc 1>,
+		<0x6000 0 0 1 &pci_intc 3>, /* Slot 12 */
+		<0x6000 0 0 2 &pci_intc 0>,
+		<0x6000 0 0 3 &pci_intc 0>,
+		<0x6000 0 0 4 &pci_intc 0>;
+	pci_intc: interrupt-controller {
+		interrupt-parent = <&intcon>;
+		interrupt-controller;
+		#address-cells = <0>;
+		#interrupt-cells = <1>;
+	};
+};
diff --git a/Documentation/devicetree/bindings/pci/fsl,imx6q-pcie.txt b/Documentation/devicetree/bindings/pci/fsl,imx6q-pcie.txt
index 83aeb1f5a645..e3d5680875b1 100644
--- a/Documentation/devicetree/bindings/pci/fsl,imx6q-pcie.txt
+++ b/Documentation/devicetree/bindings/pci/fsl,imx6q-pcie.txt
@@ -4,7 +4,11 @@ This PCIe host controller is based on the Synopsis Designware PCIe IP
 and thus inherits all the common properties defined in designware-pcie.txt.
 
 Required properties:
-- compatible: "fsl,imx6q-pcie", "fsl,imx6sx-pcie", "fsl,imx6qp-pcie"
+- compatible:
+	- "fsl,imx6q-pcie"
+	- "fsl,imx6sx-pcie",
+	- "fsl,imx6qp-pcie"
+	- "fsl,imx7d-pcie"
 - reg: base address and length of the PCIe controller
 - interrupts: A list of interrupt outputs of the controller. Must contain an
   entry for each entry in the interrupt-names property.
@@ -34,6 +38,14 @@ Additional required properties for imx6sx-pcie:
 - clock names: Must include the following additional entries:
 	- "pcie_inbound_axi"
 
+Additional required properties for imx7d-pcie:
+- power-domains: Must be set to a phandle pointing to PCIE_PHY power domain
+- resets: Must contain phandles to PCIe-related reset lines exposed by SRC
+  IP block
+- reset-names: Must contain the following entires:
+	       - "pciephy"
+	       - "apps"
+
 Example:
 
 	pcie@0x01000000 {
diff --git a/Documentation/devicetree/bindings/pci/ti-pci.txt b/Documentation/devicetree/bindings/pci/ti-pci.txt
index 60e25161f351..6a07c96227e0 100644
--- a/Documentation/devicetree/bindings/pci/ti-pci.txt
+++ b/Documentation/devicetree/bindings/pci/ti-pci.txt
@@ -1,17 +1,22 @@
 TI PCI Controllers
 
 PCIe Designware Controller
- - compatible: Should be "ti,dra7-pcie""
- - reg : Two register ranges as listed in the reg-names property
- - reg-names : The first entry must be "ti-conf" for the TI specific registers
-	       The second entry must be "rc-dbics" for the designware pcie
-	       registers
-	       The third entry must be "config" for the PCIe configuration space
+ - compatible: Should be "ti,dra7-pcie" for RC
+	       Should be "ti,dra7-pcie-ep" for EP
  - phys : list of PHY specifiers (used by generic PHY framework)
  - phy-names : must be "pcie-phy0", "pcie-phy1", "pcie-phyN".. based on the
 	       number of PHYs as specified in *phys* property.
  - ti,hwmods : Name of the hwmod associated to the pcie, "pcie<X>",
 	       where <X> is the instance number of the pcie from the HW spec.
+ - num-lanes as specified in ../designware-pcie.txt
+
+HOST MODE
+=========
+ - reg : Two register ranges as listed in the reg-names property
+ - reg-names : The first entry must be "ti-conf" for the TI specific registers
+	       The second entry must be "rc-dbics" for the DesignWare PCIe
+	       registers
+	       The third entry must be "config" for the PCIe configuration space
  - interrupts : Two interrupt entries must be specified. The first one is for
 		main interrupt line and the second for MSI interrupt line.
  - #address-cells,
@@ -19,13 +24,36 @@ PCIe Designware Controller
    #interrupt-cells,
    device_type,
    ranges,
-   num-lanes,
    interrupt-map-mask,
    interrupt-map : as specified in ../designware-pcie.txt
 
+DEVICE MODE
+===========
+ - reg : Four register ranges as listed in the reg-names property
+ - reg-names : "ti-conf" for the TI specific registers
+	       "ep_dbics" for the standard configuration registers as
+		they are locally accessed within the DIF CS space
+	       "ep_dbics2" for the standard configuration registers as
+		they are locally accessed within the DIF CS2 space
+	       "addr_space" used to map remote RC address space
+ - interrupts : one interrupt entries must be specified for main interrupt.
+ - num-ib-windows : number of inbound address translation windows
+ - num-ob-windows : number of outbound address translation windows
+ - ti,syscon-unaligned-access: phandle to the syscon DT node. The 1st argument
+			       should contain the register offset within syscon
+			       and the 2nd argument should contain the bit field
+			       for setting the bit to enable unaligned
+			       access.
+
 Optional Property:
  - gpios : Should be added if a gpio line is required to drive PERST# line
 
+NOTE: Two DT nodes may be added for each PCI controller; one for host
+mode and another for device mode. So in order for PCI to
+work in host mode, EP mode DT node should be disabled and in order to PCI to
+work in EP mode, host mode DT node should be disabled. Host mode and EP
+mode are mutually exclusive.
+
 Example:
 axi {
 	compatible = "simple-bus";