Merge tag 'gpio-v4.2-1' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-gpio

Pull gpio updates from Linus Walleij:
 "This is the big bulk of GPIO changes queued for the v4.2 kernel
  series:

   - a big set of cleanups to the aged sysfs interface from Johan
     Hovold.  To get these in, v4.1-rc3 was merged into the tree as the
     first patch in that series had to go into stable.  This makes the
     locking much more fine-grained (get rid of the "big GPIO lock(s)"
     and store states in the GPIO descriptors.

   - rename gpiod_[g|s]et_array() to gpiod_[g|s]et_array_value() to
     avoid confusions.

   - New drivers for:
      * NXP LPC18xx (currently LPC1850)
      * NetLogic XLP
      * Broadcom STB SoC's
      * Axis ETRAXFS
      * Zynq Ultrascale+ (subdriver)

   - ACPI:
      * make it possible to retrieve GpioInt resources from a GPIO
        device using acpi_dev_gpio_irq_get()
      * merge some dependent I2C changes exploiting this.
      * support the ARM X-Gene GPIO standby driver.

   - make it possible for the generic GPIO driver to read back the value
     set registers to reflect current status.

   - loads of OMAP IRQ handling fixes.

   - incremental improvements to Kona, max732x, OMAP, MXC, RCAR,
     PCA953x, STP-XWAY, PCF857x, Crystalcove, TB10x.

   - janitorial (constification, checkpatch cleanups)"

* tag 'gpio-v4.2-1' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-gpio: (71 commits)
  gpio: Fix checkpatch.pl issues
  gpio: pcf857x: handle only enabled irqs
  gpio / ACPI: Return -EPROBE_DEFER if the gpiochip was not found
  GPIO / ACPI: export acpi_gpiochip_request(free)_interrupts for module use
  gpio: improve error reporting on own descriptors
  gpio: promote own request failure to pr_err()
  gpio: Added support to Zynq Ultrascale+ MPSoC
  gpio: add ETRAXFS GPIO driver
  fix documentation after renaming gpiod_set_array to gpiod_set_array_value
  gpio: Add GPIO support for Broadcom STB SoCs
  gpio: xgene: add ACPI support for APM X-Gene GPIO standby driver
  gpio: tb10x: Drop unneeded free_irq() call
  gpio: crystalcove: set IRQCHIP_SKIP_SET_WAKE for the irqchip
  gpio: stp-xway: Use the of_property_read_u32 helper
  gpio: pcf857x: Check for irq_set_irq_wake() failures
  gpio-stp-xway: Fix enabling the highest bit of the PHY LEDs
  gpio: Prevent an integer overflow in the pca953x driver
  gpio: omap: rework omap_gpio_irq_startup to handle current pin state properly
  gpio: omap: rework omap_gpio_request to touch only gpio specific registers
  gpio: omap: rework omap_x_irq_shutdown to touch only irqs specific registers
  ...

1 files changed, 47 insertions, 0 deletions

diff --git a/Documentation/devicetree/bindings/gpio/gpio-xlp.txt b/Documentation/devicetree/bindings/gpio/gpio-xlp.txt
new file mode 100644
index 000000000000..262ee4ddf2cb
--- /dev/null
+++ b/Documentation/devicetree/bindings/gpio/gpio-xlp.txt
@@ -0,0 +1,47 @@
+Netlogic XLP Family GPIO
+========================
+
+This GPIO driver is used for following Netlogic XLP SoCs:
+	XLP832, XLP316, XLP208, XLP980, XLP532
+
+Required properties:
+-------------------
+
+- compatible: Should be one of the following:
+  - "netlogic,xlp832-gpio": For Netlogic XLP832
+  - "netlogic,xlp316-gpio": For Netlogic XLP316
+  - "netlogic,xlp208-gpio": For Netlogic XLP208
+  - "netlogic,xlp980-gpio": For Netlogic XLP980
+  - "netlogic,xlp532-gpio": For Netlogic XLP532
+- reg: Physical base address and length of the controller's registers.
+- #gpio-cells: Should be two. The first cell is the pin number and the second
+  cell is used to specify optional parameters (currently unused).
+- gpio-controller: Marks the device node as a GPIO controller.
+- nr-gpios: Number of GPIO pins supported by the controller.
+- interrupt-cells: Should be two. The first cell is the GPIO Number. The
+  second cell is used to specify flags. The following subset of flags is
+  supported:
+  - trigger type:
+	1 = low to high edge triggered.
+	2 = high to low edge triggered.
+	4 = active high level-sensitive.
+	8 = active low level-sensitive.
+- interrupts: Interrupt number for this device.
+- interrupt-parent: phandle of the parent interrupt controller.
+- interrupt-controller: Identifies the node as an interrupt controller.
+
+Example:
+
+	gpio: xlp_gpio@34000 {
+		compatible = "netlogic,xlp316-gpio";
+		reg = <0 0x34100 0x1000
+		       0 0x35100 0x1000>;
+		#gpio-cells = <2>;
+		gpio-controller;
+		nr-gpios = <57>;
+
+		#interrupt-cells = <2>;
+		interrupt-parent = <&pic>;
+		interrupts = <39>;
+		interrupt-controller;
+	};