dt-bindings: gpio: pcf857x: Convert to json-schema

Convert the PCF857x-compatible I/O expanders Device Tree binding
documentation to json-schema.

Document missing compatible values, properties, and gpio hogs.

Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Rob Herring <robh@kernel.org>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>

1 files changed, 0 insertions, 69 deletions

diff --git a/Documentation/devicetree/bindings/gpio/gpio-pcf857x.txt b/Documentation/devicetree/bindings/gpio/gpio-pcf857x.txt
deleted file mode 100644
index a482455a205b..000000000000
--- a/Documentation/devicetree/bindings/gpio/gpio-pcf857x.txt
+++ /dev/null
@@ -1,69 +0,0 @@
-* PCF857x-compatible I/O expanders
-
-The PCF857x-compatible chips have "quasi-bidirectional" I/O lines that can be
-driven high by a pull-up current source or driven low to ground. This combines
-the direction and output level into a single bit per line, which can't be read
-back. We can't actually know at initialization time whether a line is configured
-(a) as output and driving the signal low/high, or (b) as input and reporting a
-low/high value, without knowing the last value written since the chip came out
-of reset (if any). The only reliable solution for setting up line direction is
-thus to do it explicitly.
-
-Required Properties:
-
-  - compatible: should be one of the following.
-    - "maxim,max7328": For the Maxim MAX7378
-    - "maxim,max7329": For the Maxim MAX7329
-    - "nxp,pca8574": For the NXP PCA8574
-    - "nxp,pca8575": For the NXP PCA8575
-    - "nxp,pca9670": For the NXP PCA9670
-    - "nxp,pca9671": For the NXP PCA9671
-    - "nxp,pca9672": For the NXP PCA9672
-    - "nxp,pca9673": For the NXP PCA9673
-    - "nxp,pca9674": For the NXP PCA9674
-    - "nxp,pca9675": For the NXP PCA9675
-    - "nxp,pcf8574": For the NXP PCF8574
-    - "nxp,pcf8574a": For the NXP PCF8574A
-    - "nxp,pcf8575": For the NXP PCF8575
-
-  - reg: I2C slave address.
-
-  - gpio-controller: Marks the device node as a gpio controller.
-  - #gpio-cells: Should be 2. The first cell is the GPIO number and the second
-    cell specifies GPIO flags, as defined in <dt-bindings/gpio/gpio.h>. Only the
-    GPIO_ACTIVE_HIGH and GPIO_ACTIVE_LOW flags are supported.
-
-Optional Properties:
-
-  - lines-initial-states: Bitmask that specifies the initial state of each
-  line. When a bit is set to zero, the corresponding line will be initialized to
-  the input (pulled-up) state. When the  bit is set to one, the line will be
-  initialized the low-level output state. If the property is not specified
-  all lines will be initialized to the input state.
-
-  The I/O expander can detect input state changes, and thus optionally act as
-  an interrupt controller. When the expander interrupt line is connected all the
-  following properties must be set. For more information please see the
-  interrupt controller device tree bindings documentation available at
-  Documentation/devicetree/bindings/interrupt-controller/interrupts.txt.
-
-  - interrupt-controller: Identifies the node as an interrupt controller.
-  - #interrupt-cells: Number of cells to encode an interrupt source, shall be 2.
-  - interrupts: Interrupt specifier for the controllers interrupt.
-
-
-Please refer to gpio.txt in this directory for details of the common GPIO
-bindings used by client devices.
-
-Example: PCF8575 I/O expander node
-
-	pcf8575: gpio@20 {
-		compatible = "nxp,pcf8575";
-		reg = <0x20>;
-		interrupt-parent = <&irqpin2>;
-		interrupts = <3 0>;
-		gpio-controller;
-		#gpio-cells = <2>;
-		interrupt-controller;
-		#interrupt-cells = <2>;
-	};