Merge drm/drm-next into drm-misc-next

Now that 4.19-rc1 is cut, backmerge it into -misc-next.

Signed-off-by: Sean Paul <seanpaul@chromium.org>

20 files changed, 173 insertions, 35 deletions

diff --git a/Documentation/devicetree/bindings/display/bridge/analogix_dp.txt b/Documentation/devicetree/bindings/display/bridge/analogix_dp.txt
index 0c7473dd0e51..027d76c27a41 100644
--- a/Documentation/devicetree/bindings/display/bridge/analogix_dp.txt
+++ b/Documentation/devicetree/bindings/display/bridge/analogix_dp.txt
@@ -15,8 +15,6 @@ Required properties for dp-controller:
 		from common clock binding: handle to dp clock.
 	-clock-names:
 		from common clock binding: Shall be "dp".
-	-interrupt-parent:
-		phandle to Interrupt combiner node.
 	-phys:
 		from general PHY binding: the phandle for the PHY device.
 	-phy-names:
diff --git a/Documentation/devicetree/bindings/display/bridge/anx7814.txt b/Documentation/devicetree/bindings/display/bridge/anx7814.txt
index b2a22c28c9b3..dbd7c84ee584 100644
--- a/Documentation/devicetree/bindings/display/bridge/anx7814.txt
+++ b/Documentation/devicetree/bindings/display/bridge/anx7814.txt
@@ -8,8 +8,6 @@ Required properties:
 
  - compatible		: "analogix,anx7814"
  - reg			: I2C address of the device
- - interrupt-parent	: Should be the phandle of the interrupt controller
-			  that services interrupts for this device
  - interrupts		: Should contain the INTP interrupt
  - hpd-gpios		: Which GPIO to use for hpd
  - pd-gpios		: Which GPIO to use for power down
diff --git a/Documentation/devicetree/bindings/display/bridge/megachips-stdpxxxx-ge-b850v3-fw.txt b/Documentation/devicetree/bindings/display/bridge/megachips-stdpxxxx-ge-b850v3-fw.txt
index aacc8b92968c..09e0a21f705e 100644
--- a/Documentation/devicetree/bindings/display/bridge/megachips-stdpxxxx-ge-b850v3-fw.txt
+++ b/Documentation/devicetree/bindings/display/bridge/megachips-stdpxxxx-ge-b850v3-fw.txt
@@ -19,8 +19,6 @@ hardware are EDID, HPD, and interrupts.
 stdp4028-ge-b850v3-fw required properties:
   - compatible : "megachips,stdp4028-ge-b850v3-fw"
   - reg : I2C bus address
-  - interrupt-parent : phandle of the interrupt controller that services
-    interrupts to the device
   - interrupts : one interrupt should be described here, as in
     <0 IRQ_TYPE_LEVEL_HIGH>
   - ports : One input port(reg = <0>) and one output port(reg = <1>)
diff --git a/Documentation/devicetree/bindings/display/bridge/sii902x.txt b/Documentation/devicetree/bindings/display/bridge/sii902x.txt
index 56a3e68ccb80..72d2dc6c3e6b 100644
--- a/Documentation/devicetree/bindings/display/bridge/sii902x.txt
+++ b/Documentation/devicetree/bindings/display/bridge/sii902x.txt
@@ -5,8 +5,8 @@ Required properties:
 	- reg: i2c address of the bridge
 
 Optional properties:
-	- interrupts-extended or interrupt-parent + interrupts: describe
-	  the interrupt line used to inform the host about hotplug events.
+	- interrupts: describe the interrupt line used to inform the host 
+	  about hotplug events.
 	- reset-gpios: OF device-tree gpio specification for RST_N pin.
 
 Optional subnodes:
diff --git a/Documentation/devicetree/bindings/display/bridge/sii9234.txt b/Documentation/devicetree/bindings/display/bridge/sii9234.txt
index 88041ba23d56..a55bf77bd960 100644
--- a/Documentation/devicetree/bindings/display/bridge/sii9234.txt
+++ b/Documentation/devicetree/bindings/display/bridge/sii9234.txt
@@ -7,7 +7,7 @@ Required properties:
 	- iovcc18-supply : I/O Supply Voltage (1.8V)
 	- avcc12-supply : TMDS Analog Supply Voltage (1.2V)
 	- cvcc12-supply : Digital Core Supply Voltage (1.2V)
-	- interrupts, interrupt-parent: interrupt specifier of INT pin
+	- interrupts: interrupt specifier of INT pin
 	- reset-gpios: gpio specifier of RESET pin (active low)
 	- video interfaces: Device node can contain two video interface port
 			    nodes for HDMI encoder and connector according to [1].
diff --git a/Documentation/devicetree/bindings/display/bridge/sil-sii8620.txt b/Documentation/devicetree/bindings/display/bridge/sil-sii8620.txt
index 9409d9c6a260..b05052f7d62f 100644
--- a/Documentation/devicetree/bindings/display/bridge/sil-sii8620.txt
+++ b/Documentation/devicetree/bindings/display/bridge/sil-sii8620.txt
@@ -5,7 +5,7 @@ Required properties:
 	- reg: i2c address of the bridge
 	- cvcc10-supply: Digital Core Supply Voltage (1.0V)
 	- iovcc18-supply: I/O Supply Voltage (1.8V)
-	- interrupts, interrupt-parent: interrupt specifier of INT pin
+	- interrupts: interrupt specifier of INT pin
 	- reset-gpios: gpio specifier of RESET pin
 	- clocks, clock-names: specification and name of "xtal" clock
 	- video interfaces: Device node can contain video interface port
diff --git a/Documentation/devicetree/bindings/display/exynos/exynos7-decon.txt b/Documentation/devicetree/bindings/display/exynos/exynos7-decon.txt
index 9e2e7f6f7609..53912c99ec38 100644
--- a/Documentation/devicetree/bindings/display/exynos/exynos7-decon.txt
+++ b/Documentation/devicetree/bindings/display/exynos/exynos7-decon.txt
@@ -9,9 +9,6 @@ Required properties:
 
 - reg: physical base address and length of the DECON registers set.
 
-- interrupt-parent: should be the phandle of the decon controller's
-		parent interrupt controller.
-
 - interrupts: should contain a list of all DECON IP block interrupts in the
 		 order: FIFO Level, VSYNC, LCD_SYSTEM. The interrupt specifier
 		 format depends on the interrupt controller used.
diff --git a/Documentation/devicetree/bindings/display/exynos/exynos_dp.txt b/Documentation/devicetree/bindings/display/exynos/exynos_dp.txt
index ade5d8eebf85..9b6cba3f82af 100644
--- a/Documentation/devicetree/bindings/display/exynos/exynos_dp.txt
+++ b/Documentation/devicetree/bindings/display/exynos/exynos_dp.txt
@@ -25,8 +25,6 @@ Required properties for dp-controller:
 		from common clock binding: handle to dp clock.
 	-clock-names:
 		from common clock binding: Shall be "dp".
-	-interrupt-parent:
-		phandle to Interrupt combiner node.
 	-phys:
 		from general PHY binding: the phandle for the PHY device.
 	-phy-names:
diff --git a/Documentation/devicetree/bindings/display/exynos/samsung-fimd.txt b/Documentation/devicetree/bindings/display/exynos/samsung-fimd.txt
index 5837402c3ade..b3096421d42b 100644
--- a/Documentation/devicetree/bindings/display/exynos/samsung-fimd.txt
+++ b/Documentation/devicetree/bindings/display/exynos/samsung-fimd.txt
@@ -16,9 +16,6 @@ Required properties:
 
 - reg: physical base address and length of the FIMD registers set.
 
-- interrupt-parent: should be the phandle of the fimd controller's
-		parent interrupt controller.
-
 - interrupts: should contain a list of all FIMD IP block interrupts in the
 		 order: FIFO Level, VSYNC, LCD_SYSTEM. The interrupt specifier
 		 format depends on the interrupt controller used.
diff --git a/Documentation/devicetree/bindings/display/ht16k33.txt b/Documentation/devicetree/bindings/display/ht16k33.txt
index 8e5b30b87754..d5a8b070b467 100644
--- a/Documentation/devicetree/bindings/display/ht16k33.txt
+++ b/Documentation/devicetree/bindings/display/ht16k33.txt
@@ -4,8 +4,6 @@ Holtek ht16k33 RAM mapping 16*8 LED controller driver with keyscan
 Required properties:
 - compatible:		"holtek,ht16k33"
 - reg:			I2C slave address of the chip.
-- interrupt-parent:	A phandle pointing to the interrupt controller
-			serving the interrupt for this chip.
 - interrupts:		Interrupt specification for the key pressed interrupt.
 - refresh-rate-hz:	Display update interval in HZ.
 - debounce-delay-ms:	Debouncing interval time in milliseconds.
diff --git a/Documentation/devicetree/bindings/display/marvell,pxa2xx-lcdc.txt b/Documentation/devicetree/bindings/display/marvell,pxa2xx-lcdc.txt
index f79641bd5f18..45ffd6c41748 100644
--- a/Documentation/devicetree/bindings/display/marvell,pxa2xx-lcdc.txt
+++ b/Documentation/devicetree/bindings/display/marvell,pxa2xx-lcdc.txt
@@ -10,6 +10,9 @@ Required properties:
  - interrupts : framebuffer controller interrupt.
  - clocks: phandle to input clocks
 
+Optional properties:
+ - lcd-supply: A phandle to a power regulator that controls the LCD voltage.
+
 Required nodes:
  - port: connection to the LCD panel (see video-interfaces.txt)
 	 This node must have its properties bus-width and remote-endpoint set.
diff --git a/Documentation/devicetree/bindings/display/marvell,pxa300-gcu.txt b/Documentation/devicetree/bindings/display/marvell,pxa300-gcu.txt
new file mode 100644
index 000000000000..9cfae5c4e8ec
--- /dev/null
+++ b/Documentation/devicetree/bindings/display/marvell,pxa300-gcu.txt
@@ -0,0 +1,17 @@
+PXA3xx GCU Controller
+---------------------
+
+Required properties:
+ - compatible : "marvell,pxa300-gcu"
+ - reg : should contain the register range (address and length).
+ - interrupts : Controller interrupt.
+ - clocks: phandle to the PXA specific input clock.
+
+Example for PXA300:
+
+	display-controller@54000000 {
+		compatible = "marvell,pxa300-gcu";
+		reg = <0x54000000 0x1000>;
+		interrupts = <39>;
+		clocks = <&clks CLK_PXA300_GCU>;
+	};
diff --git a/Documentation/devicetree/bindings/display/mediatek/mediatek,disp.txt b/Documentation/devicetree/bindings/display/mediatek/mediatek,disp.txt
index 383183a89164..8469de510001 100644
--- a/Documentation/devicetree/bindings/display/mediatek/mediatek,disp.txt
+++ b/Documentation/devicetree/bindings/display/mediatek/mediatek,disp.txt
@@ -40,7 +40,7 @@ Required properties (all function blocks):
 	"mediatek,<chip>-dpi"        - DPI controller, see mediatek,dpi.txt
 	"mediatek,<chip>-disp-mutex" - display mutex
 	"mediatek,<chip>-disp-od"    - overdrive
-  the supported chips are mt2701 and mt8173.
+  the supported chips are mt2701, mt2712 and mt8173.
 - reg: Physical base address and length of the function block register space
 - interrupts: The interrupt signal from the function block (required, except for
   merge and split function blocks).
diff --git a/Documentation/devicetree/bindings/display/msm/dpu.txt b/Documentation/devicetree/bindings/display/msm/dpu.txt
new file mode 100644
index 000000000000..ad2e8830324e
--- /dev/null
+++ b/Documentation/devicetree/bindings/display/msm/dpu.txt
@@ -0,0 +1,131 @@
+Qualcomm Technologies, Inc. DPU KMS
+
+Description:
+
+Device tree bindings for MSM Mobile Display Subsytem(MDSS) that encapsulates
+sub-blocks like DPU display controller, DSI and DP interfaces etc.
+The DPU display controller is found in SDM845 SoC.
+
+MDSS:
+Required properties:
+- compatible: "qcom,sdm845-mdss"
+- reg: physical base address and length of contoller's registers.
+- reg-names: register region names. The following region is required:
+  * "mdss"
+- power-domains: a power domain consumer specifier according to
+  Documentation/devicetree/bindings/power/power_domain.txt
+- clocks: list of clock specifiers for clocks needed by the device.
+- clock-names: device clock names, must be in same order as clocks property.
+  The following clocks are required:
+  * "iface"
+  * "bus"
+  * "core"
+- interrupts: interrupt signal from MDSS.
+- interrupt-controller: identifies the node as an interrupt controller.
+- #interrupt-cells: specifies the number of cells needed to encode an interrupt
+  source, should be 1.
+- iommus: phandle of iommu device node.
+- #address-cells: number of address cells for the MDSS children. Should be 1.
+- #size-cells: Should be 1.
+- ranges: parent bus address space is the same as the child bus address space.
+
+Optional properties:
+- assigned-clocks: list of clock specifiers for clocks needing rate assignment
+- assigned-clock-rates: list of clock frequencies sorted in the same order as
+  the assigned-clocks property.
+
+MDP:
+Required properties:
+- compatible: "qcom,sdm845-dpu"
+- reg: physical base address and length of controller's registers.
+- reg-names : register region names. The following region is required:
+  * "mdp"
+  * "vbif"
+- clocks: list of clock specifiers for clocks needed by the device.
+- clock-names: device clock names, must be in same order as clocks property.
+  The following clocks are required.
+  * "bus"
+  * "iface"
+  * "core"
+  * "vsync"
+- interrupts: interrupt line from DPU to MDSS.
+- ports: contains the list of output ports from DPU device. These ports connect
+  to interfaces that are external to the DPU hardware, such as DSI, DP etc.
+
+  Each output port contains an endpoint that describes how it is connected to an
+  external interface. These are described by the standard properties documented
+  here:
+	Documentation/devicetree/bindings/graph.txt
+	Documentation/devicetree/bindings/media/video-interfaces.txt
+
+	Port 0 -> DPU_INTF1 (DSI1)
+	Port 1 -> DPU_INTF2 (DSI2)
+
+Optional properties:
+- assigned-clocks: list of clock specifiers for clocks needing rate assignment
+- assigned-clock-rates: list of clock frequencies sorted in the same order as
+  the assigned-clocks property.
+
+Example:
+
+	mdss: mdss@ae00000 {
+		compatible = "qcom,sdm845-mdss";
+		reg = <0xae00000 0x1000>;
+		reg-names = "mdss";
+
+		power-domains = <&clock_dispcc 0>;
+
+		clocks = <&gcc GCC_DISP_AHB_CLK>, <&gcc GCC_DISP_AXI_CLK>,
+			 <&clock_dispcc DISP_CC_MDSS_MDP_CLK>;
+		clock-names = "iface", "bus", "core";
+
+		assigned-clocks = <&clock_dispcc DISP_CC_MDSS_MDP_CLK>;
+		assigned-clock-rates = <300000000>;
+
+		interrupts = <GIC_SPI 83 IRQ_TYPE_LEVEL_HIGH>;
+		interrupt-controller;
+		#interrupt-cells = <1>;
+
+		iommus = <&apps_iommu 0>;
+
+		#address-cells = <2>;
+		#size-cells = <1>;
+		ranges = <0 0 0xae00000 0xb2008>;
+
+		mdss_mdp: mdp@ae01000 {
+			compatible = "qcom,sdm845-dpu";
+			reg = <0 0x1000 0x8f000>, <0 0xb0000 0x2008>;
+			reg-names = "mdp", "vbif";
+
+			clocks = <&clock_dispcc DISP_CC_MDSS_AHB_CLK>,
+				 <&clock_dispcc DISP_CC_MDSS_AXI_CLK>,
+				 <&clock_dispcc DISP_CC_MDSS_MDP_CLK>,
+				 <&clock_dispcc DISP_CC_MDSS_VSYNC_CLK>;
+			clock-names = "iface", "bus", "core", "vsync";
+
+			assigned-clocks = <&clock_dispcc DISP_CC_MDSS_MDP_CLK>,
+					  <&clock_dispcc DISP_CC_MDSS_VSYNC_CLK>;
+			assigned-clock-rates = <0 0 300000000 19200000>;
+
+			interrupts = <0 IRQ_TYPE_LEVEL_HIGH>;
+
+			ports {
+				#address-cells = <1>;
+				#size-cells = <0>;
+
+				port@0 {
+					reg = <0>;
+					dpu_intf1_out: endpoint {
+						remote-endpoint = <&dsi0_in>;
+					};
+				};
+
+				port@1 {
+					reg = <1>;
+					dpu_intf2_out: endpoint {
+						remote-endpoint = <&dsi1_in>;
+					};
+				};
+			};
+		};
+	};
diff --git a/Documentation/devicetree/bindings/display/msm/dsi.txt b/Documentation/devicetree/bindings/display/msm/dsi.txt
index 518e9cdf0d4b..dfc743219bd8 100644
--- a/Documentation/devicetree/bindings/display/msm/dsi.txt
+++ b/Documentation/devicetree/bindings/display/msm/dsi.txt
@@ -43,8 +43,6 @@ Optional properties:
   the master link of the 2-DSI panel.
 - qcom,sync-dual-dsi: Boolean value indicating if the DSI controller is
   driving a 2-DSI panel whose 2 links need receive command simultaneously.
-- interrupt-parent: phandle to the MDP block if the interrupt signal is routed
-  through MDP block
 - pinctrl-names: the pin control state names; should contain "default"
 - pinctrl-0: the default pinctrl state (active)
 - pinctrl-n: the "sleep" pinctrl state
@@ -121,6 +119,20 @@ Required properties:
 Optional properties:
 - qcom,dsi-phy-regulator-ldo-mode: Boolean value indicating if the LDO mode PHY
   regulator is wanted.
+- qcom,mdss-mdp-transfer-time-us:	Specifies the dsi transfer time for command mode
+					panels in microseconds. Driver uses this number to adjust
+					the clock rate according to the expected transfer time.
+					Increasing this value would slow down the mdp processing
+					and can result in slower performance.
+					Decreasing this value can speed up the mdp processing,
+					but this can also impact power consumption.
+					As a rule this time should not be higher than the time
+					that would be expected with the processing at the
+					dsi link rate since anyways this would be the maximum
+					transfer time that could be achieved.
+					If ping pong split is enabled, this time should not be higher
+					than two times the dsi link rate time.
+					If the property is not specified, then the default value is 14000 us.
 
 [1] Documentation/devicetree/bindings/clock/clock-bindings.txt
 [2] Documentation/devicetree/bindings/graph.txt
@@ -171,6 +183,8 @@ Example:
 		qcom,master-dsi;
 		qcom,sync-dual-dsi;
 
+		qcom,mdss-mdp-transfer-time-us = <12000>;
+
 		pinctrl-names = "default", "sleep";
 		pinctrl-0 = <&dsi_active>;
 		pinctrl-1 = <&dsi_suspend>;
diff --git a/Documentation/devicetree/bindings/display/msm/edp.txt b/Documentation/devicetree/bindings/display/msm/edp.txt
index 95ce19ca7bc5..eff9daff418c 100644
--- a/Documentation/devicetree/bindings/display/msm/edp.txt
+++ b/Documentation/devicetree/bindings/display/msm/edp.txt
@@ -25,10 +25,6 @@ Required properties:
 - panel-hpd-gpios: GPIO pin used for eDP hpd.
 
 
-Optional properties:
-- interrupt-parent: phandle to the MDP block if the interrupt signal is routed
-  through MDP block
-
 Example:
 	mdss_edp: qcom,mdss_edp@fd923400 {
 			compatible = "qcom,mdss-edp";
diff --git a/Documentation/devicetree/bindings/display/msm/mdp5.txt b/Documentation/devicetree/bindings/display/msm/mdp5.txt
index 1b31977a68ba..4e11338548aa 100644
--- a/Documentation/devicetree/bindings/display/msm/mdp5.txt
+++ b/Documentation/devicetree/bindings/display/msm/mdp5.txt
@@ -41,8 +41,6 @@ Required properties:
 - reg-names: The names of register regions. The following regions are required:
   * "mdp_phys"
 - interrupts: Interrupt line from MDP5 to MDSS interrupt controller.
-- interrupt-parent: phandle to the MDSS block
-  through MDP block
 - clocks: device clocks. See ../clocks/clock-bindings.txt for details.
 - clock-names: the following clocks are required.
 -   * "bus"
diff --git a/Documentation/devicetree/bindings/display/renesas,du.txt b/Documentation/devicetree/bindings/display/renesas,du.txt
index 7c6854bd0a04..ec9d34be2ff7 100644
--- a/Documentation/devicetree/bindings/display/renesas,du.txt
+++ b/Documentation/devicetree/bindings/display/renesas,du.txt
@@ -19,7 +19,6 @@ Required Properties:
 
   - reg: the memory-mapped I/O registers base address and length
 
-  - interrupt-parent: phandle of the parent interrupt controller.
   - interrupts: Interrupt specifiers for the DU interrupts.
 
   - clocks: A list of phandles + clock-specifier pairs, one for each entry in
diff --git a/Documentation/devicetree/bindings/display/sm501fb.txt b/Documentation/devicetree/bindings/display/sm501fb.txt
index 9d9f0098092b..1c79c267a57f 100644
--- a/Documentation/devicetree/bindings/display/sm501fb.txt
+++ b/Documentation/devicetree/bindings/display/sm501fb.txt
@@ -9,8 +9,6 @@ Required properties:
     - First entry: System Configuration register
     - Second entry: IO space (Display Controller register)
 - interrupts : SMI interrupt to the cpu should be described here.
-- interrupt-parent : the phandle for the interrupt controller that
-  services interrupts for this device.
 
 Optional properties:
 - mode : select a video mode:
diff --git a/Documentation/devicetree/bindings/display/tilcdc/tilcdc.txt b/Documentation/devicetree/bindings/display/tilcdc/tilcdc.txt
index 6fddb4f4f71a..7bf1bb444812 100644
--- a/Documentation/devicetree/bindings/display/tilcdc/tilcdc.txt
+++ b/Documentation/devicetree/bindings/display/tilcdc/tilcdc.txt
@@ -8,8 +8,6 @@ Required properties:
  - reg: base address and size of the LCDC device
 
 Recommended properties:
- - interrupt-parent: the phandle for the interrupt controller that
-   services interrupts for this device.
  - ti,hwmods: Name of the hwmod associated to the LCDC
 
 Optional properties:
@@ -36,7 +34,7 @@ Optional nodes:
 
  - port/ports: to describe a connection to an external encoder. The
    binding follows Documentation/devicetree/bindings/graph.txt and
-   suppors a single port with a single endpoint.
+   supports a single port with a single endpoint.
 
  - See also Documentation/devicetree/bindings/display/tilcdc/panel.txt and
    Documentation/devicetree/bindings/display/tilcdc/tfp410.txt for connecting