1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
51
52
53
54
55
56
57
58
59
60
61
62
63
64
65
66
67
68
69
70
71
72
73
74
75
76
77
78
79
80
81
82
83
84
85
86
87
88
89
90
91
92
93
94
95
96
97
98
99
100
101
102
103
104
105
106
107
108
109
110
111
112
113
114
115
116
117
118
119
120
121
122
123
124
125
126
127
128
129
130
131
132
133
134
135
136
137
138
139
140
141
142
143
144
145
146
147
148
149
150
151
152
153
154
155
156
157
158
159
160
161
162
163
164
165
166
167
168
169
170
171
172
173
174
175
176
177
178
179
180
181
182
183
184
185
186
187
188
189
190
191
192
193
194
195
196
197
198
199
200
201
|
/*******************************************************************************
This is the driver for the GMAC on-chip Ethernet controller for ST SoCs.
DWC Ether MAC 10/100/1000 Universal version 3.41a has been used for
developing this code.
This contains the functions to handle the dma.
Copyright (C) 2007-2009 STMicroelectronics Ltd
This program is free software; you can redistribute it and/or modify it
under the terms and conditions of the GNU General Public License,
version 2, as published by the Free Software Foundation.
This program is distributed in the hope it will be useful, but WITHOUT
ANY WARRANTY; without even the implied warranty of MERCHANTABILITY or
FITNESS FOR A PARTICULAR PURPOSE. See the GNU General Public License for
more details.
You should have received a copy of the GNU General Public License along with
this program; if not, write to the Free Software Foundation, Inc.,
51 Franklin St - Fifth Floor, Boston, MA 02110-1301 USA.
The full GNU General Public License is included in this distribution in
the file called "COPYING".
Author: Giuseppe Cavallaro <peppe.cavallaro@st.com>
*******************************************************************************/
#include <asm/io.h>
#include "dwmac1000.h"
#include "dwmac_dma.h"
static int dwmac1000_dma_init(void __iomem *ioaddr, int pbl, int fb, int mb,
int burst_len, u32 dma_tx, u32 dma_rx, int atds)
{
u32 value = readl(ioaddr + DMA_BUS_MODE);
int limit;
/* DMA SW reset */
value |= DMA_BUS_MODE_SFT_RESET;
writel(value, ioaddr + DMA_BUS_MODE);
limit = 10;
while (limit--) {
if (!(readl(ioaddr + DMA_BUS_MODE) & DMA_BUS_MODE_SFT_RESET))
break;
mdelay(10);
}
if (limit < 0)
return -EBUSY;
/*
* Set the DMA PBL (Programmable Burst Length) mode
* Before stmmac core 3.50 this mode bit was 4xPBL, and
* post 3.5 mode bit acts as 8*PBL.
* For core rev < 3.5, when the core is set for 4xPBL mode, the
* DMA transfers the data in 4, 8, 16, 32, 64 & 128 beats
* depending on pbl value.
* For core rev > 3.5, when the core is set for 8xPBL mode, the
* DMA transfers the data in 8, 16, 32, 64, 128 & 256 beats
* depending on pbl value.
*/
value = DMA_BUS_MODE_PBL | ((pbl << DMA_BUS_MODE_PBL_SHIFT) |
(pbl << DMA_BUS_MODE_RPBL_SHIFT));
/* Set the Fixed burst mode */
if (fb)
value |= DMA_BUS_MODE_FB;
/* Mixed Burst has no effect when fb is set */
if (mb)
value |= DMA_BUS_MODE_MB;
#ifdef CONFIG_STMMAC_DA
value |= DMA_BUS_MODE_DA; /* Rx has priority over tx */
#endif
if (atds)
value |= DMA_BUS_MODE_ATDS;
writel(value, ioaddr + DMA_BUS_MODE);
/* In case of GMAC AXI configuration, program the DMA_AXI_BUS_MODE
* for supported bursts.
*
* Note: This is applicable only for revision GMACv3.61a. For
* older version this register is reserved and shall have no
* effect.
*
* Note:
* For Fixed Burst Mode: if we directly write 0xFF to this
* register using the configurations pass from platform code,
* this would ensure that all bursts supported by core are set
* and those which are not supported would remain ineffective.
*
* For Non Fixed Burst Mode: provide the maximum value of the
* burst length. Any burst equal or below the provided burst
* length would be allowed to perform.
*/
writel(burst_len, ioaddr + DMA_AXI_BUS_MODE);
/* Mask interrupts by writing to CSR7 */
writel(DMA_INTR_DEFAULT_MASK, ioaddr + DMA_INTR_ENA);
/* RX/TX descriptor base address lists must be written into
* DMA CSR3 and CSR4, respectively
*/
writel(dma_tx, ioaddr + DMA_TX_BASE_ADDR);
writel(dma_rx, ioaddr + DMA_RCV_BASE_ADDR);
return 0;
}
static void dwmac1000_dma_operation_mode(void __iomem *ioaddr, int txmode,
int rxmode)
{
u32 csr6 = readl(ioaddr + DMA_CONTROL);
if (txmode == SF_DMA_MODE) {
pr_debug("GMAC: enable TX store and forward mode\n");
/* Transmit COE type 2 cannot be done in cut-through mode. */
csr6 |= DMA_CONTROL_TSF;
/* Operating on second frame increase the performance
* especially when transmit store-and-forward is used.
*/
csr6 |= DMA_CONTROL_OSF;
} else {
pr_debug("GMAC: disabling TX SF (threshold %d)\n", txmode);
csr6 &= ~DMA_CONTROL_TSF;
csr6 &= DMA_CONTROL_TC_TX_MASK;
/* Set the transmit threshold */
if (txmode <= 32)
csr6 |= DMA_CONTROL_TTC_32;
else if (txmode <= 64)
csr6 |= DMA_CONTROL_TTC_64;
else if (txmode <= 128)
csr6 |= DMA_CONTROL_TTC_128;
else if (txmode <= 192)
csr6 |= DMA_CONTROL_TTC_192;
else
csr6 |= DMA_CONTROL_TTC_256;
}
if (rxmode == SF_DMA_MODE) {
pr_debug("GMAC: enable RX store and forward mode\n");
csr6 |= DMA_CONTROL_RSF;
} else {
pr_debug("GMAC: disable RX SF mode (threshold %d)\n", rxmode);
csr6 &= ~DMA_CONTROL_RSF;
csr6 &= DMA_CONTROL_TC_RX_MASK;
if (rxmode <= 32)
csr6 |= DMA_CONTROL_RTC_32;
else if (rxmode <= 64)
csr6 |= DMA_CONTROL_RTC_64;
else if (rxmode <= 96)
csr6 |= DMA_CONTROL_RTC_96;
else
csr6 |= DMA_CONTROL_RTC_128;
}
writel(csr6, ioaddr + DMA_CONTROL);
}
static void dwmac1000_dump_dma_regs(void __iomem *ioaddr)
{
int i;
pr_info(" DMA registers\n");
for (i = 0; i < 22; i++) {
if ((i < 9) || (i > 17)) {
int offset = i * 4;
pr_err("\t Reg No. %d (offset 0x%x): 0x%08x\n", i,
(DMA_BUS_MODE + offset),
readl(ioaddr + DMA_BUS_MODE + offset));
}
}
}
static unsigned int dwmac1000_get_hw_feature(void __iomem *ioaddr)
{
return readl(ioaddr + DMA_HW_FEATURE);
}
static void dwmac1000_rx_watchdog(void __iomem *ioaddr, u32 riwt)
{
writel(riwt, ioaddr + DMA_RX_WATCHDOG);
}
const struct stmmac_dma_ops dwmac1000_dma_ops = {
.init = dwmac1000_dma_init,
.dump_regs = dwmac1000_dump_dma_regs,
.dma_mode = dwmac1000_dma_operation_mode,
.enable_dma_transmission = dwmac_enable_dma_transmission,
.enable_dma_irq = dwmac_enable_dma_irq,
.disable_dma_irq = dwmac_disable_dma_irq,
.start_tx = dwmac_dma_start_tx,
.stop_tx = dwmac_dma_stop_tx,
.start_rx = dwmac_dma_start_rx,
.stop_rx = dwmac_dma_stop_rx,
.dma_interrupt = dwmac_dma_interrupt,
.get_hw_feature = dwmac1000_get_hw_feature,
.rx_watchdog = dwmac1000_rx_watchdog,
};
|
